●Allspecificationsinthiscatalogandproductionstatusofproductsaresubjecttochangewithoutnotice.Priortothepurchase,pleasecontactNECTokinforupdatedproductdata.
●Pleaserequestforaspecificationsheetfordetailedproductdatapriortothepurchase.
●Beforeusingtheproductinthiscatalog,pleaseread"Precautions"andothersafetyprecautionslistedintheprintedversioncatalog.
06.09.01P0766EDMN01VOL05E
13
ConductivePolymertype
PS/LSeries
QPERFORMANCECHARACTERISTICS Test Conditions : Conform to IEC 60384-1
at 85℃
at 105℃
at 85℃
at 120 Hz
at 100 kHz
Reflow soldering method 240℃,
10 sec.Max.
10V
8V
13V
16V
12.8V
20V
4V
3.3V
5.2V
6.3V
5V
8V
2.5V
2V
3.3V
Lower than initial
specification
Parts shall be temperature cycled
over a temperature range of -55 to
+105℃, five times continuously as
follow.
Step 1: -55 ℃, 30±3min.
Step 2: room temp. , 10 to 15min.
Step 3: 105 ℃, 30±3min.
Step 4: room temp, 10 to 15min.
at 40℃
at 90 to 95% RH
500 hour
at 85℃
at rated voltage
1000 hour
Strength : 4.9N
Time : 10±0.5sec.
(two directions)
Lower than initial
specification
Lower than initial
specification
PERFORMANCE TEST CONDITION
Operating temperature
Rated voltage (V.dc)
Derated voltage (V.dc)
Surge voltage (V.dc)
Capacitance
Capacitance tolerance
DC Leakage Current (L.C)
Dissipation Factor
Equivalent Series Resistance
-55℃ to +105℃
ITEM
Surge voltage test
2.2 μF to 1000 μF
L.C
Refer to Standard Ratings
Refer to Standard Ratings
Refer to Standard Ratings
at 120 Hz
±20%
l
0
= 1% / 1000 hour
Visual:
There shall be no evidence of mechanical damage
Refer to Standard Ratings
from +30% to -20%
Refer to Standard Ratings
at 85℃: rated voltage
at 105℃: derated voltage
Lower than initial
specification
Lower than 1.5 times initial
specification
Endurance Ⅰ
Lower than initial
specification
Refer to Standard Ratings Lower than 3 times initial
specification
Endurance Ⅱ
Damp heat
Failure Rate
Terminal Strength
Lower than 1.5 times initial
specification
Voltage:
Rated voltage for 5min.
Temperature : 85±2℃
Applied voltage : Surge voltage
Series resistance : 33 ohm
Duration of surge : 30±5 sec
Time between surge : 5.5min.
Number of cycle : 1000
0.1C • V(μA) or 3mA (J case:10μA) , whichever is greater
Lower than initial
specification
Lower than initial
specification
Capacitance change DF(%)
Rapid change of
temperature
Resistance to Soldering
heat
Characteristic
at high and low
temperature
Lower than 1.3 times initial
specification
-55℃
+105℃
from 0 to –20%
from 0 to +50%
Lower than initial
specification
Refer to Standard Ratings
Lower than initial
specification
Lower than 1.5 times
initial specification
Lower than 10 times
initial specification
Step 1: 25±2℃
Step 2: -55 ℃
Step 3: 25±2℃
Step 4: 105 ℃
0
-3
0
-3
0
-3
0
-3
Permissible ripple current Refer to Ratings Table at 100 kHz
Conform to IEC60384-1 Conform to IEC60384-1Other
at 105℃
at Derated voltage
1000 hour
————
Derate voltage at 85℃ at more
*1
[U
T
]=[U
R
]‒ [U
R
]‒[U
C
]
20
Reference:Deratedvoltage(85to105°C)
[U
T
]:Deratedvoltageatoperatingtemperature
[U
R
]:Ratedvoltage
[U
C
]:Deratedvoltageat105°C
T :Ambienttemperature
(T‒85)
*1: Refer to the page 47 “NOTES ON USING NeoCapacitor/2. Mounting/(1) Refl ow soldering/(b) Temperature and time”