User's Guide
SNVA614BJanuary 2012Revised January 2014
AN-2205 LM25118 Evaluation Board
1 Introduction
The LM25118 Evaluation Board is designed to provide the design engineer with a fully functional,
Emulated Current Mode Control, buck-boost power converter to evaluate the LM25118 controller IC. The
evaluation board provides a 12 V output with 3 A of output current capability. The evaluation board’s wide
input voltage range is from 42 V to 5 V, with operation down to 3 V with some component changes. The
evaluation board operates at 300 kHz, a good compromise between conversion efficiency, tradeoffs
between buck and buck-boost mode requirements, and converter size. The printed circuit board consists
of 4 layers with 2 ounce copper top and bottom, and 1 ounce copper on internal layers. The board is
constructed with FR4 material. This user' guide contains the evaluation board schematic, bill-of-materials
(BOM) and a quick setup procedure. For more complete circuit and design information, see the
LM25118/LM25118Q Wide Voltage Range Buck-Boost Controller (SNVS726) data sheet and quick start.
The performance of the evaluation board is as follows:
Input Range: 42 V to less than 5 V at Full Current
Operation to 3 V at Reduced Current and Appropriate Adjustments*
Output Voltage: 12 V
Output Current: 0 to 3 A
Frequency of Operation: 300 kHz
Board Size: 3.45 X 2.65 inches
Load Regulation: 1%
Line Regulation: 0.1%
Over-Current Limiting
Operation with VIN Greater or Less than VOUT
*Operation at full current to around 3 V is possible with current limit sense resistor, UVLO threshold, and
corresponding Cramp adjustment. Additional input capacitance may be required. For more details, see the
LM25118/LM25118Q Wide Voltage Range Buck-Boost Controller (SNVS726) data sheet.
2 IC Features
Integrated High and Low Side Driver
Internal High Voltage Bias Regulator
Wide Input Voltage Range: 5 V to 42 V
Emulated Current Mode Control
Single Inductor Architecture
VOUT Operation below and above VIN
Single Resistor Sets Oscillator Frequency
Oscillator Synchronization Capability
Programmable Soft-Start
Ultra Low (<10 µA) Shutdown Current
Enable Input
Wide Bandwidth Error Amplifier
All trademarks are the property of their respective owners.
1
SNVA614BJanuary 2012Revised January 2014 AN-2205 LM25118 Evaluation Board
Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated
(8) FB
VIN (1) (16) VCC
RT (3)
(18) HB
VOUT
AGND (6)
PGND (14)
DAP (EP)
(13) CSG
RAMP (5)
SS (7)
(12) CS
(15) LO
(10) VOUT
(19) HO
(20) HS
(9) COMP
LM25118MH
VIN (5V to 42V)
EN (4)
SYNC (11)
VCCX (17)
UVLO (2)
Package
www.ti.com
Adjustable Output Voltage 1.23 V 38 V
1.5% Feedback Reference Accuracy
Thermal Shutdown
No VIN to VOUT Connection during Fault Protection
3 Package
HTSSOP-20EP (Exposed Pad)
4 Application Circuit
See the detailed LM25118EVAL schematic at Figure 17.
2AN-2205 LM25118 Evaluation Board SNVA614BJanuary 2012Revised January 2014
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
www.ti.com
Efficiency
5 Efficiency
Figure 1. Efficiency
Figure 1 illustrates the efficiency of the converter vs. input voltage and output current. These curves
highlight the high efficiency of the converter, especially considering the simplicity of design offered by a
non synchronous implementation. Note the discontinuity in the curves at approximately 17 V and 13 V
which represent mode transition boundaries. The lower efficiencies in the buck-boost region reflect
additional losses at higher input and inductor currents. The decrease in efficiency at higher input voltages
represents higher switching losses.
6 Air Flow
Prolonged operation without airflow at low input voltage and at at full power will cause the MOSFET’s and
Diodes to overheat. A fan with a minimum of 200 LFM should always be provided. Figure 2 illustrates the
temperature rise of various components with no airflow. The ambient was 25°C, and VIN was 8 V.
Figure 2. Temperature vs Load Current With No Airflow 25°C Ambient
3
SNVA614BJanuary 2012Revised January 2014 AN-2205 LM25118 Evaluation Board
Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated
Powering Up
www.ti.com
7 Powering Up
Connecting the IC’s enable pin to ground will allow powering up the source supply with a minimal output
load. Set the current limit of the source supply to provide about 1.5 times the anticipated wattage of the
load. Note that input currents become very high at low input voltages, which requires an appropriate input
supply. As you remove the connection from the enable pin to ground, immediately check for 12 V at the
output.
A quick efficiency check is the best way to confirm that everything is operating properly. If something is
amiss, you can be reasonable sure that it will affect the efficiency adversely. Few parameters can be
incorrect in a switching power supply without creating losses and potentially damaging heat.
8 Over Current Protection
The evaluation board is configured with over-current protection. The output current is limited to
approximately 4.5 A in the buck-boost mode The 4.5 A value allows for component tolerances to specify a
3 A output current. Note this current will be almost double, or about 7 A in buck mode (VIN greater than
17 V) due to the difference in peak inductor currents in the two different modes.
Figure 3. Short Circuit Current
9 VCCX
A place for a jumper between VOUT and VCCX is provided on the PC board. If operation below about 5 V
is required, connect the jumper to allow VCCX to power the converter (the exact voltage depends on the
gate drive requirements of the switching FETs). The converter does require a minimum VIN of 5 V to
initially start. When running, the input voltage can decrease to below 5 V at reduced current with VCCX
connected to VOUT. Note that this design uses a current limit value to specify a full 3 A of output current
at a minimum VIN of 5 V. For operation lower than 5 V, the current limit resistor, UVLO threshold, and
ramp capacitor must be re-calculated. Caution: make sure the input supply can source the required input
current. Operation at low VIN at full power may overheat and damage the MOSFET’s and Diodes supplied
on the board. Note there is a limit of 14 V applied to VCCX. Never exceed this value if operating VCCX
from an external source, or operating the board with VOUT greater than 12 V. To prevent oscillation,
connect and additional 100 uF or greater electrolytic capacitor across VIN for input voltages less than 5 V.
10 Mode Transition
With VOUT set at 12 V, the LM25118 applications board will operate in the buck mode with VIN greater than
about 17 V. As VIN is reduced below 17 V, the converter begins to operate in a soft buck-boost mode. As
VIN is decreased below 14 V, the converter smoothly transitions to a pure buck-boost mode. This method
of mode transition insures a smooth, glitch free operation as VIN is varied over the transition region.
4AN-2205 LM25118 Evaluation Board SNVA614BJanuary 2012Revised January 2014
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
www.ti.com
Mode Transition
Figure 4. Mode Transition
Figure 4 illustrates soft mode transition. The boost switch pulse-width is relatively narrow compared to the
buck switch waveform. The boost switch pulse-width will gradually increase as VIN decreases, and will
eventually match and lock to the buck switch waveform. At this point, the converter enters full buck-boost
operation.
5
SNVA614BJanuary 2012Revised January 2014 AN-2205 LM25118 Evaluation Board
Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated
Typical Waveforms
www.ti.com
11 Typical Waveforms
Note: All waveforms refer to Rev B design.
Figure 5. VIN = 10 V, IOUT = 1 A, illustrating Figure 6. VIN = 18 V, IOUT = 3 A Illustrating
Buck-Boost Operation Buck Operation
CH1: VSW = 20V/div; CH2: Q1 = 20V/div; CH1: VSW = 20V/div; CH2: Q1 = 20V/div;
CH3: Q2 = 10V/div; CH4: IL= 5A/div CH3: Q2 = 10V/div; CH4: IL= 2A/div
Figure 7. Buck Mode Transient Response Figure 8. Buck-Boost Mode Transient Response
CH2: VOUTripple (ac coupled); CH4: IOUT CH2: VOUTripple (ac coupled); CH4: IOUT
6AN-2205 LM25118 Evaluation Board SNVA614BJanuary 2012Revised January 2014
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
www.ti.com
Typical Waveforms
Figure 9. Start Up Waveforms
CH1: VIN; CH2: VOUT;
CH3: VCC; CH4: VUVLO
7
SNVA614BJanuary 2012Revised January 2014 AN-2205 LM25118 Evaluation Board
Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated
Bill of Materials
www.ti.com
12 Bill of Materials
Quant Designator Description Manufacturer PartNumber
ity
5 C1, C2, C3, C4, C5 CAP, CERM, 2.2uF, 100V, +/-20%, X7R, 1812 TDK C4532X7R2A225M
3 C6, C16, C17 CAP, CERM, 0.1uF, 100V, +/-10%, X7R, 0603 MuRata GRM188R72A104KA35D
2 C7, C8 CAP, AL, 180uF, 16V, +/-20%, 0.026 ohm, SMD Nippon Chemi-Con APXH160ARA181MJ80G
2 C9, C10 CAP, CERM, 47uF, 16V, +/-10%, X5R, 1210 MuRata GRM32ER61C476KE15L
2 C11, C12 CAP, CERM, 0.47uF, 25V, +/-10%, X7R, 1206 AVX 12063C474KAT2A
1 C13 CAP, CERM, 0.1uF, 100V, +/-10%, X7R, 0805 Kemet C0805C104K1RACTU
1 C15 CAP, CERM, 2200pF, 100V, +/-10%, X7R, 0603 MuRata GRM188R72A222KA01D
1 C18 CAP, CERM, 330pF, 100V, +/-5%, C0G/NP0, 0603 MuRata GRM1885C2A331JA01D
2 C20, C21 CAP, CERM, 1uF, 25V, +/-10%, X7R, 0805 MuRata GRM219R71E105KA88D
1 C22 (Rev A) CAP, CERM, 4700pF, 100V, +/-10%, X7R, 0603 TDK C1608X7R2A472K
1 C22 (Rev B) CAP, CERM, 0.1uF, 100V, +/-10%, X7R, 0603 TDK C1608X7S2A104K
1 D2 Diode, Schottky, 35V, 10A, DPAK ON Semiconductor MBRD1035CTLT4G
1 D3 Diode, Schottky, 100V, 20A, DDPAK Vishay VB40100C-E3/4W
4 J1, J2, J3, J4 Terminal, Turret, TH, Double Keystone 1503-2
1 L1 Inductor, Shielded E Core, Ferrite, 10uH, 18A, Coilcraft SER2915H-103KL
0.00186 ohm, SMD
2 Q1, Q2 MOSFET, N-CH, 75V, 12A, PowerPAK SO-8 Vishay-Siliconix SI7148DP
1 R2 RES, 75.0k ohm, 1%, 0.125W, 0805 Vishay-Dale CRCW080575K0FKEA
1 R3 RES, 1.00Meg ohm, 1%, 0.125W, 0805 Vishay-Dale CRCW08051M00FKEA
1 R4 RES, 0 ohm, 5%, 0.25W, 1206 Vishay-Dale CRCW12060000Z0EA
1 R5 RES, 0 ohm, 5%, 0.1W, 0603 Vishay-Dale CRCW06030000Z0EA
1 R6 RES, 0.015 ohm, 1%, 2W, 3008 Susumu Co Ltd RL7520WT-R015-G
1 R8 RES, 2.67k ohm, 1%, 0.1W, 0603 Vishay-Dale CRCW06032K67FKEA
1 R9 RES, 10.0 ohm, 1%, 0.1W, 0603 Vishay-Dale CRCW060310R0FKEA
1 R10 RES, 10.0k ohm, 1%, 0.1W, 0603 Vishay-Dale CRCW060310K0FKEA
1 R11 RES, 29.4k ohm, 0.1%, 0.1W, 0603 Yageo America RT0603BRD0729K4L
1 R12 (Rev A) RES, 16.2k ohm, 1%, 0.1W, 0603 Vishay-Dale CRCW060316K2FKEA
1 R12 (Rev B) RES, 18.2k ohm, 1%, 0.1W, 0603 Panasonic ERJ-3EKF1822V
1 R14 RES, 309 ohm, 1%, 0.1W, 0603 Vishay-Dale CRCW0603309RFKEA
2 TP1, TP9 Test Point, TH, Multipurpose, Black Keystone 5011
1 TP2 Test Point, TH, Multipurpose, Red Keystone 5010
2 TP3, TP4, TP7, TP8 Test Point, TH, Multipurpose, White Keystone 5012
1 U1 Wide Voltage Range Buck-Boost Controller, 20-pin Texas Insturments LM25118MH/NOPB
TSSOP-EP, Pb-Free
0 C14, C19, R7, R13 DNP
0 D1 Diode, Schottky, 100V, 0.2A, SOD-123 ST BAT41ZFILM
Microelectronics
0 R1 RES, 0 ohm, 5%, 0.125W, 0805 Vishay-Dale CRCW08050000Z0EA
8AN-2205 LM25118 Evaluation Board SNVA614BJanuary 2012Revised January 2014
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
www.ti.com
Printed Circuit Board Layout
13 Printed Circuit Board Layout
Figure 10. Top Layer as Viewed from Top Figure 11. Copper Layer 1 (Top) as Viewed from Top
Figure 12. Copper Layer 2 (Mid-Layer 1) as Viewed Figure 13. Copper Layer 3 (Mid-Layer 2) as Viewed
from Top from Top
9
SNVA614BJanuary 2012Revised January 2014 AN-2205 LM25118 Evaluation Board
Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated
Printed Circuit Board Layout
www.ti.com
Figure 14. Copper Layer4 (Bottom) as Viewed from Figure 15. Bottom Layer as Viewed from Top
Top
Figure 16. Drill Guide and Board Dimensions as Viewed from Top
10 AN-2205 LM25118 Evaluation Board SNVA614BJanuary 2012Revised January 2014
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
www.ti.com
Evaluation Board
14 Evaluation Board
Figure 17. Evaluation Board Schematic
11
SNVA614BJanuary 2012Revised January 2014 AN-2205 LM25118 Evaluation Board
Submit Documentation Feedback Copyright © 2012–2014, Texas Instruments Incorporated
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
Important Notice for Users of EVMs for RF Products in Japan
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1. 電波法施行規則第6条第1項第1号に基づく平成18328日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
2. 実験局の免許を取得後ご使用いただく。
3. 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
   上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
3. Since the EVM is not a completed product, it may not meet all applicable regulatory and safety compliance standards (such as UL,
CSA, VDE, CE, RoHS and WEEE) which may normally be associated with similar items. You assume full responsibility to determine
and/or assure compliance with any such standards and related certifications as may be applicable. You will employ reasonable
safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even if the EVM should fail to
perform as described or expected.
4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM25118EVAL/NOPB