THICK FILM CHIP JUMPER RESISTOR THICK FILM CHIP JUMPER RESISTOR FEATURES Miniature and light weight. Suit for reflow and wave flow solder. Stable electrical capability, high reliability. Low assembly cost, suit for automatic SMT equipment. Superior mechanical and frequency characteristics. RoHS compliant ROHS TYPE DESIGNATION EXAMPLE R S 0 3 0 0 0 Thick film chip fixed resistor Code Code Tolerance Normal Power Series S Upgraded Power Series Packing Style Tape & Reel 10m T G 20m B 50m Code Packing Style Code Code C L -4A Type Code Power rating series C F J T Power Rating Series Code Product Code Resistance Tolerance Code J Resistance Value Code Type 01 0201 02 0402 03 0603 05 0805 06 1206 1210 1210 10 2010 12 2512 000 Jumper is expressed by 000 Lead-free Level Code Code Lead-free Level ( 100ppm) No Terminal Lead-free Marking ( pb content in terminal 100ppm) Bulk Case Case L G 12 ( 1000ppm) Low Lead ( pb content in resistor body 1000ppm) ( 100ppm) Low Lead ( pb content in resistor body 100ppm) Rated current code Code (A) Rated Current No For Normal Spec Marking -2A 2 -3A 3 -4A 4 -5A 5 -6A 6 -7A 7 -8A 8 -9A 9 -AA 10 -BA 11 -CA 12 -DA 13 -EA 14 -FA 15 -GA 16 CONSTRUCTION AND DIMENSION L a W t b TYPE L unit:mm W t a b 0201 0.60 0.05 0.30 0.05 0.23 0.05 0.10 0.05 0.15 0.05 0402 1.00 0.10 0.50 0.10 0.30 0.10 0.20 0.10 0.25 0.10 0603 1.60 0.15 0.80 0.15 0.40 0.10 0.30 0.20 0.30 0.20 0805 2.00 0.20 1.25 0.15 0.50 0.10 0.30 0.20 0.40 0.20 1206 3.20 0.20 1.60 0.15 0.55 0.10 0.50 0.20 0.50 0.20 1210 3.20 0.20 2.50 0.20 0.55 0.10 0.50 0.20 0.50 0.20 2010 5.00 0.20 2.50 0.20 0.55 0.10 0.60 0.20 0.60 0.20 2512 6.40 0.20 3.20 0.20 0.55 0.10 0.60 0.20 0.60 0.20 13 THICK FILM CHIP JUMPER RESISTOR APPEARANCE , The surface of resistor is covered with Protective Coating which hard to fade, and the surface of coating should avoid unevenness. The terminal part is covered equable , the plating is hard to fade, and should avoid unevenness, flaw, pinhole and discoloration. With a clear mark , the resistor body is crack-free. REFERENCE STANDARD GB/T 5729-2003 GB/T 9546-1995 DERATING CURVE Percent ratedload - 55 100 70 75 50 25 155 -55 -50 - 25 0 25 50 75 100 Ambient temperature 70 ( For resistors operated in ambient over 70 ( 125 150 175 ) ) ,rated load (power rating or current rating) shall be derated in accordance with the above figure. RATINGS Item Rated Current Max.Overload Current 0201 0402 0603 0805 1206 1210 2010 2512 0.5A 1A 1A 2A 2A 2A 2A 2A 1A 2A 3A 5A 5A 5A 5A 5A Resistance Tolerance Operating Temperature Range F( 0201: -55 ~+125 10m ),G( 0402 20m 0603 70 Rated Temperature 14 ),J( 0805 50m 1206 Special type chip jumper Refer to type designation 2 2 times Rated current ) 1210 2010 2512 -55 ~+155 CHARACTERISTICS Item Bending Strength Temperature Cycling Short Time Overload Steady state humidity 70 Load Life GB/T 5729-2003 Test Methods (GB/T 5729-2003) Specifications No mechanical damage R 50m (J ) R 20m (G ) R 10m (F ) 0201 1812 (Bending Distance): 0402 0603 0805 1206 2010 2512 1mm (duration):10S 1S -55 No mechanical damage R 50m (J ) R 20m (G ) R 10m (F ) 30 ~ 2 ~3 1210 3mm ~125 30 5 -55 30min ~normal temperature 2min~3min ~125 30min 5 cycles No mechanical damage R 50m (J ) R 20m (G ) R 10m (F ) 5S Apply Max. overload current for 5 seconds No mechanical damage R 100m (J ) R 40m (G ) R 20m (F ) 40 40 No mechanical damage 70 2 ,1000 70 2 ,1000h,Rated current 1.5h on/0.5h off R 100m (J ) R 40m (G ) R 20m (F ) 2 2 90 90 ~95 ~95 RH 1000 RH 1000h , 1.5 / 0.5 No mechanical damage Endurance at upper temperature Resistance to Solvent Insulation Resistance Resistance to Soldering Heat R 100m (J ) R 40m (G ) R 20m (F ) 0201 type chip resistor should be exposed at 125 2 in the test chamber for 1000 hours. 0402 0603 0805 1206 1210 2010 2512 type chip resistor should be exposed at 155 2 in the test chamber for 1000 hours. No mechanical damage R 50m (J ) R 20m (G ) R 10m (F ) 1000M 10h 1h Dip in chloroethylene for 10h 100V , 1 , . Apply DC 100V between substrate and termination for 1 minute, then check insulation resistance . Min No mechanical damage R 50m (J ) R 20m (G ) R 10m (F ) Solderability 95% 95% Cover Min Adhesion No mechanical damage 1h. 270 5 10s 1s 240 5 2s 0.5s 5N 10s 1s Applying 5N for 10s 15 1s THICK FILM CHIP JUMPER RESISTOR PACKAGING Tape and reel 0201 Paper taping 0402 0603 0805 1206 1210: unit:mm TYPE A B W F E 0201 0.70 0.1 0.40 0.1 8.0 0.20 3.5 0.05 1.75 0.1 0402 1.20 0.1 0.70 0.1 8.0 0.20 3.5 0.05 1.75 0.1 0603 1.85 0.1 1.10 0.1 8.0 0.20 3.5 0.05 1.75 0.1 0805 2.35 0.1 1.65 0.1 8.0 0.20 3.5 0.05 1.75 0.1 1206 3.50 0.2 1.90 0.2 8.0 0.20 3.5 0.05 1.75 0.1 1210 3.50 0.2 2.80 0.2 8.0 0.20 3.5 0.05 1.75 0.1 TYPE P P0 P1 D0 T T1:0.28 0.04 T:0.42 0.05 0201 2.0 0.05 4.0 0.1 2.0 0.05 1.5 0.1 0402 2.0 0.05 4.0 0.1 2.0 0.05 1.5 0.1 0.42 0.05 0603 4.0 0.1 4.0 0.1 2.0 0.05 1.5 0.1 0.60 0.1 0805 4.0 0.1 4.0 0.1 2.0 0.05 1.5 0.1 0.75 0.1 1206 4.0 0.1 4.0 0.1 2.0 0.05 1.5 0.1 0.75 0.1 1210 4.0 0.1 4.0 0.1 2.0 0.05 1.5 0.1 0.75 0.1 Remark:For 0201type,T1 refers to the hole depth of paper carrier tape,T refers to the thickness of the paper carrier tape. 16 Embossed taping P0 D0 E B0 F W A0 D1 P P1 K0 A0 K0 t B0 t TYPE A0 B0 W F E t 2010 5.50 0.15 2.82 0.15 12.00 0.10 5.50 0.10 1.75 0.10 0.25 0.05 2512 6.78 0.15 3.45 0.15 12.00 0.10 5.50 0.10 1.75 0.10 0.25 0.05 TYPE P P0 P1 D0 D1 K0 2010 4.00 0.10 4.00 0.10 2.00 0.05 1.50+0.10/-0 1.50 0.10 0.84 0.10 2512 4.00 0.10 4.00 0.10 2.00 0.05 1.50+0.10/-0 1.50 0.10 0.81 0.10 Reel B C M D A W T 17 THICK FILM CHIP JUMPER RESISTOR TYPE M W T A B C D 0201 0402 9.5 178 0603 2.0 0805 2.0 12.5 1.0 1.5 13.0 15.5 0.5 1.5 0.5 13.0 21.0 58.0 0.5 0.5 2.0 13.0 21.0 57.0 0.5 0.5 2.0 1206 1210 2010 178 2.0 2.0 0.5 2512 Bulk case unit:mm 12 31 36 110 PACKAGING QUANTITY Packaging style Tape and reel Type 0201 0402 0603 0805 1206 1210 PCS Quantity 10000 5000 2010 2512 4000 Bulk Bulk case 0201 0402 0603 0805 1206 1210 2010 2512 50000 25000 10000 5000 1500 1000 18 0201 0402 50000 0603 0805 1206 10000 1210 2010 2512 4000