HSHM-H088FR7-8CPX-TG30 - 3M

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering inform at io n call

800-225-5373

3M™ MetPak™ HSHM Press-Fit Header

2 mm Type FR, 88 Signal Contacts, 8 Rows, Straight HSHM Series

Physical

Performance

Environmental

MetPak is a trademark of 3M Company.

Insulation

Material: High Temperature Thermoplastic (LCP)

Flammability: UL 94V-0

Contact

Material: Copper Alloy

Plating: See Ordering Informatio n

Mechanical

Normal Force (Nominal): 0.57 N [ 58 g ] Signal, 0.74 N [ 75 g ] Shield

Engagement Force (Nominal): 0.32 N [ 33 g [ Signal, 0.22 N [ 22 g ] Shield

Separation Force (Nominal): 0.20 N [ 20 g ] Signal, 0.20 N [ 20 g ] Shield

Wipe (Nominal, Shortest Contact): 2.67 mm [ 0.105 in. ] Sign al, 1.57 mm [ 0.062 in ] Shield

Durability: 250 cycles with TR40B pl ating

Application: This module is not suitable for stand-alone use, (Refer to IEC-61076-4-101)

Electrical Data Rate:5 Gb/s

Characteristic Impedance: 50 Ω Single-ended, 100 Ω Differential

Current Rating (Fully Loaded): 1 A at 70° C Signal

Insulation Resistance: 104 MΩ at 100 VDC

Withstanding Voltage: 750VRMS

Temperature Rating: -55°C to +125°C

Date Modified: March 27, 2007

• Up to 5 Gb/s data rates

• Low crosstalk at high frequencies

• 50/100 Ω (single-ended /differential) impedance

• Modular/scalable format IEC 61076-4-101

• 101 mated lines per linear inch

• End-to-end stackable with 8 row 3M ™ MetPak™

CP2, HM and HSHM headers

• See Regulatory Information Appendix (RIA)

for chemical compliance information

TS-2062-02

Sheet 1 of 3

UL File No.: E68080

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

denotes s hield column (tail o nly) om itted for the row

differential pair part

ROW F

ROW E

ROW D

ROW C

ROW B

ROW A

ROW Z

Pin pos iti o ns

Shield positions

12345678910

1234567891011

Row differential configuration

shown with prot ect i ve c a ps *

* Caps to be removed after press-fit installation process

DIM A = Pin mating length

DIM B = Shield tail length

DIM C = Pin tail length

Coaxial, column diff erential and stripline configuration

shown with protective caps*

HSHM-HXXXXX-8XPX-XXXXX

REV X XXYY

HSHM-HXXXXX-8XPX-XXXXX

REV X XXYY

1.50

.059

18.00

.709

2.00

.079

2.00

.079

2.00

.079

2.00

.079

20.00

.787

ROW G

ROW H

ROW I

24.92

.981

21.40

.843

15.00

.591 5.00

.197

13.40

.528

4.50

.177

DIM C

DIM A

DI M B

Interstitial

ground

contacts

Signal

contacts

3M™ MetPak™ HSHM Press-Fit Header

2 mm Type FR, 88 Signal Contacts, 8 Rows, Straight HSHM Series

Ordering Information

0 0.0 0.00

mm ±3 ±0.3 ±0.13

[inch]

Tolerance Unless Noted

[ ] Dimensions for Reference Only

HSHM - H088FRX - 8CPX - XXXXX

High Speed Option:

1 =Row differential applications

4 =Coaxial and column differential applicat ions

7 =Stripline application (75 Ω)

Plating μm [ μ″ ]:

TG30 = 0.76 [ 30 ] Min. Au Contact Area

2.54 [ 100 ] Min. SnPb Terminal Area (RIA E2 & C2 apply)

1.27 [ 50 ] Min. Ni All over

TR40B = 0.127 [ 5 ] Min. Hard Au Contact Area, Lubricated

1.02 [ 40 ] Min. PdNi Contact Area

0.10 [ 4 ] Min. Pd Strike Contact Area

2.54 [ 100 ] Min. SnPb Terminal Area (RIA E2 & C2 apply)

1.27 [ 50 ] Min. Ni all over

(Rows I and Z not loaded)

Standard Configuration

DIM A = 5.3 mm for rows A through H

For non-standard configurations

contact sales representative TS-2062-02

Sheet 2 of 3

Interconnect Solutions

http://www.3M.com/interconnects/

3M is a trademark of 3M Company.

For technical, sales or ordering information call

800-225-5373

3M™ MetPak™ HSHM Press-Fit Header

2 mm Type FR, 88 Signal Contacts, 8 Rows, Straight HSHM Series

TS-2062-02

Sheet 3 of 3

FINISHED HOLE DIA. ("D") Cu. THICKNESS SnPb THICKNESS DRILLED HOLE DIA.

0.45 7 - 0.559 [.01 80 - .0 22 0] 0.025 - 0.0 45 [.0010 - . 0 018] 0.008 -0.018 [.0003 - .0007] 0.584 - 0.625 [.0230 - .0246]

HOLE PLATING TABLE mm [i n.]

Re c ommen ded PC B ho le mounting patt e r n for co axial,

colu m n diff erential and stri pline applications Recommended PCB hole mounting pattern for row

differenti al app l icatio ns

(Same geometry as lef t view wit hou t the grou nd vias)

Pl ated thru hole s

See hole platin g table

lO0.10 MAB

O2.00 +0.05

ABCDE A

ABCDE 1

FGH

3.00

20.00

2.00

1.00

2.00

O DIM. D

6.00

lO0.10 A B

Regulatory Information Appendix

3M Electronic Solutions Division/Interconnect

EUROPE

Appendix E1: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product is RoHS Compliant 2005/95/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/

EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E2: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC

This product contains lead in the compliant pin area in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/747/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision 2005/618/

EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in writing, this

information represents 3M’s best knowledge and belief based upon information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E3: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment as

amended by Commission Decision 2005/618/EC.

This product contains lead in the solder tail area in excess of the maximum concentration value allowed.

Unless otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon

information provided by third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix E4: European Union RoHS

Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical & Electronic Equipment, as

amended by EU Commission Decision 2005/618/EC.

This product contains decaBDE in the insulating material in excess of the maximum concentration value allowed but is

compliant by exemption under EU Commission Decision 2005/17/EC.

“RoHS Compliant 2005/95/EC” means that the product or part (“Product”) does not contain any of the substances in

excess of the maximum concentration values in EU Directive 2002/95/EC, as amended by Commission Decision

2005/618/EC, unless the substance is in an application that is exempt under EU RoHS. Unless otherwise stated by 3M in

writing, this information represents 3M’s best knowledge and belief based upon information provided by third party

suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

RIA-2217-B

CHINA

Appendix C1: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits

for Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,

means that the product or part does not contain any of the following substances in excess of the following maximum

concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent chromium,

polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless otherwise

stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information provided by

third party suppliers to 3M.

In the event any product is proven not to conform with 3M’s Regulatory Information Appendix, then 3M’s entire liability

and Buyer’s exclusive remedy will be in accordance with the Warranty stated below.

Appendix C2: China RoHS

Electronic Industry Standard of the People’s Republic of China, SJ/T11363-2006, Requirements for Concentration Limits

for Certain Hazardous Substances in Electronic Information Products.

This symbol, per Marking for the Control of Pollution Caused by Electronic Information Products, SJ/T11364-2006,

means that the product or part does contain a substance, as detailed in the chart below, in excess of the following

maximum concentration values in any homogeneous material: (a) 0.1% (by weight) for lead, mercury, hexavalent

chromium, polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium. Unless

otherwise stated by 3M in writing, this information represents 3M’s best knowledge and belief based upon information

provided by third party suppliers to 3M.

The numerical reference in the symbol above should not be construed as a representation regarding the product’s life or an

extension of a product warranty. The product warranty is stated below. In the event any product is proven not to conform

with 3M’s Regulatory Information Appendix, then 3M’s entire liability and Buyer’s exclusive remedy will be in

accordance with the product Warranty stated below.

Important Notice

All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the

accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended

application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s

current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in

writing, by an authorized officer of 3M.

Warranty; Limited Remedy; Limited Liability.

This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER

WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to

replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any

indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of the legal theory asserted.

Electronic Solutions Division

6801 River Place Blvd.

Austin, TX 78726-9000

800/225-5373

www.3M.com/interconnects RIA-2217-B

Name and Content of Hazardous Substances or Elements