DATA SHEET TFT COLOR LCD MODULE NL10276AC30-03L 38 cm (15.0 inches), 1024 x 768 pixels, fullcolor, High luminance, Wide viewing angle, multiscan function, built-in CRT interface board DESCRIPTION The NL10276AC30-03L is a TFT (thin film transistor) active-matrix color liquid crystal display (LCD) comprising an amorphous silicon TFT attached to each signal electrode, a driving circuit, CRT interface board, and a backlight. The NL10276AC30-03L has a built-in backlight with an inverter. The 38 cm (15.0 inch) diagonal display area contains 1024 x 768 pixels and can display fullcolor (more than 16 million colors simultaneously). Also, it has a wide viewing angle and multiscan function. FEATURES * High luminance (350 cd/m2 typ.) * Wide viewing angle * Multi-scan function: e.g., XGA, SVGA, VGA, VGATEXT, MAC * Low reflection * Incorporated edge-type backlight (Individually two * CRT interface board lamps into two lamp holders, inverter) Auto recognition of input signal: Analog RGB signals, synchronous signals (Hsync, Vsyn, composite) * Lamp holders replaceable (Part No.: 150LHS13) * Approved by UL1950 Third Edition and CSA-C22.2 No.950-95 Digital control: e.g. brightness, display position On-Screen Display (OSD) Free supply voltage sequence Application with the OSD function might conflict with Corresponds to DDCI and DDC2B patents in Europe and/or the U.S.A Corresponds to VESA DPMS If you apply the OSD function, please do so in accordance with the patent regulations of your location. VESA: Video Electronics Standards Association DPMS: Display Power Management Signaling DDC1: Display Data Channel 1 DDC2B: Display Data Channel 2B APPLICATIONS * Desktop PCs * Engineering workstations * Monitors for process controllers The information in this document is subject to change without notice. Please confirm the delivery specification before starting to design your system. Document No. EN0512EJ1V0DS00 (1st edition) Date Published October 2000 P CP(N) Printed in Japan (c) 2000 NL10276AC30-03L STRUCTURE AND FUNCTION A color TFT (thin film transistor) LCD module is comprised of a TFT liquid crystal panel structure, LSIs for driving the TFT array, and a backlight assembly. The TFT panel structure is created by sandwiching liquid crystal material in the narrow gap between a TFT array glass substrate and a color filter glass substrate. After the driver LSIs are connected to the panel, the backlight assembly is attached to the back side of the panel. RGB (red, green, blue) data signals from a source system are modulated into a form suitable for active-matrix addressing by the onboard signal processor and sent to the driver LSIs, which in turn address the individual TFT cells. Acting as an electro-optical switch, each TFT cell regulates light transmission from the backlight assembly when activated by the data source. By regulating the amount of light passing through the array of red, green, and blue dots, color images are created with clarity. CHARACTERISTICS (at room temperature) Items 2 Description Display area 304.128 (H) x 228.096 (V) mm Drive system a-Si TFT active matrix Display colors Fullcolor Number of pixels 1024 (H) x 768 (V) Pixel arrangement RGB vertical stripe Pixel pitch 0.297 (H) x 0.297 (V) mm Module size 350.0 (H) x 265.0 (V) x 22.5 (D) mm (typ.) Weight 1680 g (typ.) Contrast ratio 250:1 (typ.) Viewing angle (more than the contrast ratio of 10:1) * * Horizontal: 55 (typ., left side, right side) Vertical: 45 (typ., up side, down side) Designed viewing direction * * Optimum gray-scale ( = 2.2): perpendicular Best contrast angle: down side 5 Color gamut 40% (typ., at center, to NTSC) Response time 15 ms (typ.), "white 100%" to "black 10%" Luminance 350 cd/m (typ.) Signal system Analog RGB signals, synchronous signals (Hsync and Vsync or composite) Backlight Edge light type: four cold cathode fluorescent lamps with an inverter Lamp holder: 150LHS13 Inverter: 150PW131 Supply voltage 12 V, 12 V (logic/LCD driving, backlight) Power consumption 28.2 W (typ.) 2 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L BLOCK DIAGRAM I/F LCD module R G B HS/CS Vsync AIF Sync. Signal PLL CLK Timing Controller OSD LEDON LEDOFF SEL UP DOWN EXIT LEFT RIGHT RESET MENUSEL AMP Control signal Signal recognition Control signal H-driver ON/OFF 3072 lines V-driver LCD panel DC/DC converter VDD (+12 V) 768 lines H: 1024 x 3 (R, G, B) V: 768 Brightness control VDDB (+12 V) GNDB Inverter Backlight GND HS: Hsync CS: Composite synchronous signal Note: Neither GND nor GNDB is connected to Frame. These should be connected in customer equipment. Data Sheet EN0512EJ1V0DS00 3 NL10276AC30-03L GENERAL SPECIFICATIONS Item Description Unit Module size 350 0.6 (H) x 265.0 0.6 (V) x 23.5 (max.) (D) mm Display area 304.128 (H) x 228.096 (V) [Diagonal 38 cm (15.0)] mm Number of dots 1024 x 3 (H) x 768 (V) dots Pixel pitch 0.297 (H) x 0.297 (V) mm Dot pitch 0.099 (H) x 0.297 (V) mm RGB (Red, Green, Blue) vertical stripe - Full color color 1680 (typ.) 1730 (max.) g Pixel arrangement Display colors Weight ABSOLUTE MAXIMUM RATINGS Parameter Symbol Rating Unit VDD -0.3 to +14 V VDDB -0.3 to +14 V Logic input voltage VIn1 -0.3 to +5.5 V R,G,B input voltage VIn2 -6.0 to +6.0 V Storage temp. Tst -20 to +60 C Operating temp. Top 0 to +50 C Module surface % Ta 40C Supply voltage Relative humidity (RH) 95 Note 2 85 Absolute humidity Note 2 Absolute humidity shall not exceed Ta = 50C, RH = 85 % Ta = 25C Ta = 25C VDD = 12 V - 40 < Ta 50C g/m 3 Notes: 1. Measured at the display area (including self-heat.) 2. No condensation 4 Remarks Data Sheet EN0512EJ1V0DS00 Ta > 50C Note 1 NL10276AC30-03L ELECTRICAL CHARACTERISTICS (1) Logic, LCD Driving, Backlight (Ta = 25C) Item Symbol Min. Typ. Max. Unit VDD 10.8 12.0 13.2 V Logic and LCD driving VDDB 10.8 12.0 13.2 V Backlight Logic input "L" voltage VIL 0 - 0.8 V - Logic input "H" voltage VIH 2.2 - 5.25 V Logic output "L" voltage VOL - - 0.4 V Logic output "H" voltage VOH 2.4 - - V Logic input "L" current 1 IOL1 - - 3.0 A Logic input "H" current 1 IOH1 -1.0 - - A Logic output "L" current IIL -1.0 - - A Logic output "H" current I1H - - 1.0 A Supply current IDD - 620 Note 900 mA VDD = 12.0 V - 185 200 mA Power-saving mode VDD = 12.0 V - 1700 1850 mA VDDB = 12.0 V (Max. luminance) - 20 30 mA Power-saving mode VDDB = 12.0 V Min. Typ. Max. Unit 0 (black) 0.7 (white) *A Vp-p DC input level (black) -0.5 - +2.5 V Sync level -0.2 0.3 *B (0.6) Vp-p - - 1.4 Vp-p Supply voltage IDDB Remarks DDCDAT DDCDAT HS/CS, Vsync Note: Checker flag pattern (In EIAJ ED-2522) (2) Video Signal (R, G, B) Input (Ta = 25C) Items Maximum amplitude (black - white) *A + *B Remarks Note - G terminal (sync on green) - Note: Needs to adjust contrast ratio if the input level is beyond 0.7 Vp-p. Remark: You may see noise on the display if input video sinal have noise. And the frequency is bad characteristics, the display becomes blurry indication. Data Sheet EN0512EJ1V0DS00 5 NL10276AC30-03L Power Supply Design (1) Note that the supply voltage must not be applied while the control signals (SEL, UP, DOWN, EXIT, LEFT, RIGHT, and RESET) are connected to GND. Otherwise, the module may malfunction. (2) If the power supply voltage is applied while UP and DOWN are connected to GND, the input control signals become ineffective and all key inputs are neglected. To reset this mode, turn off the power once and then turn on the power while UP and DOWN are connected to GND. The mode will be released. (3) Do not change the MENUSEL setting while the module is being operated. MENUSEL selection (hierarchical type or toggle type) is continuously set during the power supply voltage is applied. (4) Inverter current wave The inverter current wave is as follows. 1700 (mA) 0 (mA) Duty Luminance control frequency Maximum luminance control: 100% (Duty) Minimam luminance control: 20% (Duty) Luminance control frequency = Input Vsync frequency x K Input Vsync frequency 75 Hz: K = 4.6 Input Vsync frequency > 75 Hz: K = 3.6 Please set up like above diagram. (5) Ripple of supply voltage Supply voltage VDD (for logic and LCD driver) VDDB (for backlight) 100 mVp-p 200 mVp-p Acceptable range Remark: The acceptable range of ripple voltage includes spike noise. Example of the power supply connection a) Separate the power supply Power VDD Power VDDB b) Put in the filter Power Filter* VDD Filter* VDDB Filter* (reference value) L = 10 H to 100 H C = 10 F to 100 F 6 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (6) Fuses Supply voltage Part No. Supplier Ratings Remarks VDD CCFINTE3.15 KOA 60VDC/3.15A - VDDB 1 ICP-S2.3 T104 ROHM 72VDC/2.3A 1 or 2 is used. 2 CCP2E40H KOA 72VDC/2.0A Note 1 Note: Please design power-supply capacity for the more than 1.5 times of the fuse rating from the safety point of view. In case where the capacity is under the 1.5 times of the rating, the LCD module should be enough evaluated about safety in the case of the short circuit. INTERFACE PIN CONNECTIONS (1) Logic and LCD driving CN1 Part No.: 1-353119-4 Adaptable socket: 1-353068-4 Supplier: Tyco Electronics AMP K.K. Pin No. Symbols Pin No. Symbols 1 B 8 Vsync 2 BGND 9 GND 3 G 10 HS/CS 4 GGND 11 GND 5 R 12 DDCCLK 6 RGND 13 N.C. 7 GND 14 DDCDAT Figure from socket view 1 2 * * * * * * 13 14 Note: N.C. (No connection) must be open. Data Sheet EN0512EJ1V0DS00 7 NL10276AC30-03L CN3 Part No.: DF14A-25P-1.25H Adaptable socket: DF14-25S-1.25C (Gold-Plated terminals) Supplier: Hirose Electric Co., Ltd. Pin No. Symbols Pin No. Symbols 1 LEDON 14 EXIT 2 LEDOFF 15 GND 3 GND 16 N.C. 4 N.C. 17 GND 5 N.C. 18 GND 6 RIGHT 19 MENUSEL 7 LEFT 20 N.C. 8 RESET 21 N.C. 9 N.C. 22 N.C. 10 GND 23 GND 11 SEL 24 N.C. 12 UP 25 N.C. 13 DOWN Figure from socket view 1 2 * * * 24 25 Note: N.C. (No connection) must be open. CN5 Part No.: IL-Z-8PL-SMTY Adaptable socket: IL-Z-8S-S125C3 Supplier: Japan Aviation Electronics Industry, Limited (JAE) Pin No. Symbols Pin No. Symbols 1 VDD 5 GND 2 VDD 6 GND 3 VDD 7 GND 4 VDD 8 GND Figure from socket view 8 8 Data Sheet EN0512EJ1V0DS00 7 * * * * * 2 1 NL10276AC30-03L (2) Backlight CN201 Part No.: IL-Z-11PL1-SMTY Adaptable socket: IL-Z-11S-S125C3 Supplier: Japan Aviation Electronics Industry, Limited (JAE) Pin No. Symbols Pin No. Symbols 1 VDDB 7 N.C. 2 VDDB 8 N.C. 3 VDDB 9 N.C. 4 GNDB 10 N.C. 5 GNDB 11 N.C. 6 GNDB Figure from socket view 11 10 * * * 2 1 Note: N.C. (No connection) must be open. Rear view 1 CN1 14 1 1 11 CN201 CN3 25 8 CN5 1 Data Sheet EN0512EJ1V0DS00 9 NL10276AC30-03L (3) PIN FUNCTIONS Symbol I/O Logic HS/CS Input Negative/ Positive Horizontal synchronous signal input or composite synchronous signal input (TTL level), positive/negative auto recognition Vsync Input Negative/ Positive Vertical synchronous signal input (TTL level), positive/negative auto recognition, clock input for DDC1 R Input - Red video signal input (0.7 Vp-p, input impedance 75 ) G Input - Green video signal input (0.7 Vp-p, input impedance 75 ) B Input - Blue video signal input (0.7 Vp-p, input impedance 75 ) LEDON Output Positive Indicator for LED power on "H": LED select; "L": Other status LEDOFF Output Positive Indicator for power saving mode "H": Power saving mode select; "L": Other status DDCCLK Input Positive CLK for DDC2B DDCDAT Input/ Output Positive Data for DDC1/2B Read/Write SEL Input Negative Control function select signal (TTL level) SEL is pulled up in the module. Details of the functions are mentioned in CONTROL FUNCTIONS, Page 14. "H" or "open": SEL off; "L": SEL on UP Input Negative Control signal (TTL level) The signal increases the value of the selected function. UP is pulled up in the module. "H" or "open": UP off; "L": UP on DOWN Input Negative Control signal (TTL level) The signal decreases the value of the selected function. DOWN is pulled up in the module. "H" or "open": DOWN off; "L" : DOWN on EXIT Input Negative Control function exit signal (TTL level) EXIT is pulled up in the module. "H" or "open": EXIT off; "L": EXIT on Input Negative Control signal (TTL level) The signal increases the value of the selected function. RIGHT is pulled up in the module. "H" or "open": RIGHT off; "L": RIGHT on Input Negative Control signal (TTL level) The signal decreases the value of the selected function. LEFT is pulled up in the module. "H" or "open": LEFT off; "L": LEFT on Input Negative Control signal (TTL level) The signal initializes the selected function. RESET is pulled up in the module. "H" or "open": RESET off; "L": RESET on Input - RIGHT LEFT Note 1 Note 1 RESET Note 1 MENUSEL 10 Description OSD menu select signal (TTL level) MENUSEL is pulled up in the module. "H or open": Hierarchical type "L": Toggle type For details, see Page 11, OSD Menu Select. Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L Symbol I/O Logic Description VDD - - Power supply for logic and LCD driving +12 V (10%) VDDB - - Power supply for backlight +12 V (10%) GND - - Ground for system RGND GGND BGND - - Ground for R, G, B analog data GNDB - - Ground for backlight Note: This terminal becomes effective only when the value of Button Sel is 7. Detail of the functions is mentioned in page 27, INITIAL VALUE CHANGE FUNCTIONS. Remarks 1: Neither GND nor GNDB is connected to Frame. These should be connected in customerequipment. 2: 12 V for backlight should be started up within 300 ms, othernise, the protection circuit makes the backlight turn off. (4) OSD MENU SELECT OSD menu type Hierarchical type Toggle type MENUSEL "H" or "open" "L" How to adjust For details, see page 27, INITIAL VALUE CHANGE FUCNTIONS. For details, see page 27, INITIAL VALUE CHANGE FUCNTIONS. MENU Auto Adjust Brightness Clock Position Contrast Notes: 1. If the OSD menu type is changed, the adjustment values become default. Then, it takes 5 seconds to display the changed menu after the supply voltage is input again. Indicators for both LEDON and LEDOFF are "ON" during the 5 seconds. 2. The initial value of the Contrast ratio is as follows. Hierarchical type : 128:1 (typ.) Toggle type : 100:1 (typ.) Data Sheet EN0512EJ1V0DS00 11 NL10276AC30-03L (5) Equivalent Circuit Symbol R, G, B I/O Equivalent circuit Input Input 75 HS/CS, Vsync Input 10k Input LEDON LEDOFF Output RN2306 (Toshiba) Or equivalent Output Example of LED circuit LCD module Output R (330 ) LED LEDON LEDOFF R (330 ) SEL UP DOWN SW EXIT RIGHT LEFT RESET MENUSEL 12 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L INPUT SIGNALS (1) Synchronous Signal This module is corresponding to the synchronous signals below. Synchronous signal Auto recognition mode HS/CS Vsync Sync. on Green Input Input Input or no input Composite synchronous mode Input (cs) No input Input or no input Sync. on Green mode No input No input Input Input (HS) No input Input or no input No input Input Input or no input No Input No input No input Separate synchronous signal mode (HS, Vsync) Power-saving mode Notes: 1. Power-saving mode corresponds to VESA DPMS. 2.y The module recognizes the Sync on Green signal automatically, when the FUNC in SOG Sel of Sel Data is "Y". Refer to Page 27, Initial Value Chance Functions. (2) Preset Timing The fourteen kinds of timings below are already programmed in this module. The input synchronous signals are automatically recognized. Display size Vsync (Hz) Hsync (kHz) SYSTEM CLK (MHz) V Pulse (H) V B.Porch (H) H Pulse (CLK) H B.Porch (CLK) Sync Logic V, H 1 640 x 400 56.432 24.830 21.053 8 25 96 48 -,- Note 2 640 x 480 59.992 31.469 25.175 2 33 96 48 -,- VGA 3 720 x 400 70.087 31.469 28.322 2 35 108 45 +,- VGA TXT 4 800 x 600 60.317 37.879 40.000 4 23 128 88 +,+ VESA 5 640 x 480 66.667 35.000 30.240 3 39 64 96 S on G 6 640 x 480 75.000 37.500 31.500 3 16 64 120 -,- VESA 7 720 x 400 85.039 37.927 35.500 3 42 36 144 +,- VESA 8 640 x 480 85.008 43.269 36.000 3 25 48 112 -,- Note 9 1024 x 768 60.004 48.363 65.000 6 29 136 160 -,- VESA 10 800 x 600 75.000 46.875 49.500 3 21 80 160 +,+ VESA 11 832 x 624 74.565 49.735 57.283 3 39 64 224 S on G 12 800 x 600 85.061 53.674 56.250 3 27 64 152 +,+ Note 13 1024 x 768 70.069 56.476 75.000 6 29 136 144 +,+ VESA 14 1024 x 768 75.029 60.023 78.750 3 28 96 176 +,+ VESA 3UHVHW No. Remarks Macintosh Macintosh Note: Out of specification. Data Sheet EN0512EJ1V0DS00 13 NL10276AC30-03L Remarks 1: Even if the one of preset timing is entered, a little adjustment of the functions such as horizontal period, CLK delay and display position is required. The adjusted values are memorized in every preset Number. 2: This module recognizes the synchronous signals with near preset timing of the frequency of HS, Vsync, even if the signals other than the preset timing that were entered. For instance, it is displayed with presetting number 6 in the case of 640 x 480 dot; HS: 37.861kHz; Vsync: 72.809 Hz. Please note that using other than the preset timings may cause incorrect magnification ratios, unfitness of control functions, or other display problems. 3: The display color scale may be different between Sync on Green input and the others. CONTROL FUNCTIONS (1) Expansion Modes Expansion mode is a function by which expand the screen size in different resolutions. For example, the VGA signal has 640 x 480 pixels. But if the display data can be expanded to 1.6 times vertically and horizontally, the VGA screen image can be displayed fully on a screen with XGA resolution. This module automatically recognizes the timing shown in Preset Timing as an expansion mode. Please adopt this mode after evaluating display quality, because the appearance in expansion mode may degrade in some cases. The following table shows display magnifications for each mode. Magnifications Input Signals 14 Number of Pixels Vertical Horizontal XGA 1024 x 768 1.0 1.0 SVGA 800 x 600 1.25 1.25 VGA 640 x 480 1.6 1.6 VGA text 720 x 400 1.92 / 1.6 hierarchical/toggle 1.42 MAC 832 x 624 1.2 1.2 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L Display Image (a) SVGA mode (800 x 600) XGA (1024 x 768) Black display area Horizontal: x 1.25 (1000 pixels) Vertical: x 1.25 (750 pixels) (b) VGA mode (640 x 480) Horizontal: x 1.6 (1024 pixels) Vertical: x 1.6 (768 pixels) (c) VGA text mode (720 x 400) (i) Hierarchical type select XGA (1024 x 768) Black display area Horizontal: x 1.42 (1022 pixels) Vertical: x 1.92 (768 pixels) (ii) Toggle type select XGA (1024 x 768) Black display area Horizontal: x 1.42 (1022 pixels) Vertical: x 1.6 (640 pixels) (d) 832 x 624 MAC mode (832 x 624) XGA (1024 x 768) Black display area Horizontal: x 1.2 (998 pixels) Vertical: x 1.2 (748 pixels) Data Sheet EN0512EJ1V0DS00 15 NL10276AC30-03L (2) DDC Function This function corresponds to VESA DDCTM and EDIDTM (Structure Version 1). Follow the specifications of the IC when you write data. (VCLK is fixed on "H.") Write a data into the necessary addresses in advance when using this function. Data "55H" in address "00H" and "FFH" in other address have already been programmed upon shipping. The input equivalent circuit diagram is as follows. EDID: Extended Display Identification Data Internal circuit diagram Vsync VCLK DDCCLK SCL DDCDAT SDA Product: Microchip Technology, Inc. 24LC21A or equivalent (3) DPMS This function corresponds to the VESA DPMSTM standard. VESA DPMS Standard NL10276AC30-03L Signal State Power-saving Horizontal Vertical Recovery-time Power-saving Video Recoverytime On Pulses Pulses Active None Not applicable None Not applicable Standby No pulses Pulses Blanked Minimum Short Maximum Short Suspend Pulses No pulses Blanked Substantial Longer Maximum Short Off No pulses No pulses Blanked Maximum System dependent Maximum Short Remark: The power consumption of power saving mode is different between Sync. On Green and others. The power consumption of Sync on Green is higher than others because of synchronous separation circuit. 16 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (4) Control Function Items No. Form Function items 1 Auto adjust Clock and position auto adjust 2 Brightness Brightness of backlight control 3 Clock 4 5 6 Position Contrast Color Level H. Size Horizontal display period adjust Clock Phase CLK phase adjust H. Position Horizontal position adjust V. Position Vertical position adjust W, R, G, B White level of video signals; synchronous color and each color control W White level of video signal synchronous color control W, R, G, B Color level of video signals; synchronous color and each color control W Color level of video signal synchronous color control 7 Information Video signal information Display multi scan function, Hsync and Vsync frequency 8 OSD Position OSD position adjust The display position of OSD can be moved. 9 Config Sync on Green signal. Response or non response to Sync on Green signal is selected. When non response is selected (see Page 27, Initial Value Change Functions), config is not displayed. 10 All Reset Reset to initial value. The values in No. 1 to No. 6, No. 8 and No. 9 are returned to the initial values. Remarks 1: 1 In order to achieve the best picture quality, the above functions should be adjusted by setting the SEL, UP, DOWN, LEFT, RIGHT, RESET, and EXIT signals. clock and position adjusted values are memorized every display modes. 2 The memorized values are not affected even if the power is switched off. But the selected value is not memorized if a selected mode is not completed. 2: The auto-adjusted values may not become the optimal values for the best picture quality by customer equipment and display screens. And the Auto adjust function does not work correctly when both Sync On Green signal and separate synchronous signals are input in this module. In that case, please adjust each function (clock and position). 3: Screen may be disturbed only a moment when each adjusted value is changed. Data Sheet EN0512EJ1V0DS00 17 NL10276AC30-03L (5) Control Function Flow Chart (a) Hierarchical type (Number of adjust switch is 4:SEL; UP; DOWN; EXIT) For details, see page 27, Initial Value Change Functions - 6. Sel Data, Button Sel. Start (SEL): OSD opens (EXIT): OSD closes MENU Auto Adjust Brightness Clock Position Contrast (SEL) (EXIT), (SEL) Auto Adjust (DOWN) (UP) No Yes (UP), (DOWN) (EXIT) Auto Adjust No MENU Auto Adjust Brightness Clock Position Contrast (UP), (DOWN) (SEL): Auto Adjust Yes (EXIT): OSD closes (SEL) (EXIT) (UP), (DOWN) Brightness (DOWN) (UP) (SEL) (SEL), (EXIT) Reset Brightness No Yes (UP), (DOWN)) (UP), (DOWN)) Continued on next page 18 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (UP), (DOWN)) (UP), (DOWN)) Reset Brightness (DOWN) (EXIT): Cancel (UP) No MENU Auto Adjust Brightness Clock Position Contrast (SEL): Initialize Yes (EXIT): OSD closes (SEL) (EXIT) (UP) H. Size (DOWN) Clock Phase (UP) (UP), (DOWN) (SEL) (EXIT) (UP) / (DOWN) (SEL): Reset H. Size H. Size Clock Phase This operation which is the same as H. Size adjusts. H. Size (UP), (DOWN) MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (UP) Clock Phase (EXIT): OSD closes (SEL) (EXIT) (DOWN) (EXIT) H. Position This operation is the same as Clock phase adjustment. V. Position Continued on next page Data Sheet EN0512EJ1V0DS00 19 NL10276AC30-03L (DOWN) (UP) MENU Auto Adjust Brightness Clock Position Contrast (EXIT): OSD closes (SEL) (EXIT) [S-Cnt Sel is ON] (SEL), (UP), (DOWN), (EXIT) (DOWN) (UP) Contrast W R G B For details, see page 27, Initial Value Change Functions - 6. Sel Data. [S-Cnt Sel is OFF] (UP) / (DOWN) Contrast W * MENU Color Level Information OSD Position Config All Reset (EXIT): OSD closes (SEL) (EXIT) [S-Lvl Sel is ON] (SEL), (UP), (DOWN), (EXIT) (DOWN) (UP) Color Level W R G B Color Level W For details, see page 27, Initial Value Change Functions - 6. Sel Data. [S-Cnt Sel is OFF] (UP) / (DOWN) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) Continued on next page 20 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (DOWN) (UP) (SEL) (EXIT) Information 1024 x 788 Hf 60.0 kHz Vf 75.0 Hz * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (EXIT): OSD closes (SEL) (EXIT) (UP) / (DOWN): OSD Position select OSD Position Center Center/LeftUp/RightUp/ LeftDown/RightDown (SEL): Reset OSD Position (EXIT): OSD closes (SEL) (EXIT) (UP) / (DOWN): Select "Sync on Green" acceptability [ON/OFF] Sync on Green OFF (SEL): Reset Sync on Green (EXIT): OSD closes * Config is not indicated when SoG Sel MENU "N" of page 27, Initial Value Change Functions - 6. Sel Data is selected. (SEL) (EXIT) All Reset No Yes (UP), (DOWN) (EXIT) (UP), (DOWN) All Reset (SEL): All reset No Yes Data Sheet EN0512EJ1V0DS00 21 NL10276AC30-03L (b) Hierarchical type (Number of adjust switch is 7:SEL; UP, DOWN; EXIT; LEFT; RIGHT; RESET) For details, see page 27, Initial Value Change Functions - 6. Sel Data, Button Sel. Start (SEL): MENU open MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (EXIT): OSD closes (SEL) (EXIT), (SEL) Auto Adjust (UP) No Yes (LEFT), (RIGHT), (UP), (DOWN) (LEFT), (RIGHT), (UP), (DOWN) (EXIT) Auto Adjust No MENU Auto Adjust Brightness Clock Position Contrast (SEL): Auto Adjust Yes (EXIT): OSD closes (SEL) (EXIT) (LEFT), (RIGHT) Brightness (DOWN) (UP) (RESET) (SEL), (EXIT) Reset Brightness No Yes (LEFT), (RIGHT), (UP), (DOWN) (LEFT), (RIGHT), (UP), (DOWN) Continued on next page 22 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (LEFT), (RIGHT), (UP), (DOWN) (LEFT), (RIGHT), (UP), (DOWN) (DOWN) (UP) Reset Brightness No Yes (EXIT): OSD closes MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (EXIT): Cancel (SEL): Initialize (EXIT) (SEL) (LEFT) / (RIGHT) (RESET): Reset H. Size H. Size (UP) Clock Phase (UP), (DOWN) (EXIT) H. Size (UP), (DOWN) (LEFT) / (RIGHT) (RESET): Reset Clock Phase Clock Phase MENU Auto Adjust Brightness Clock Position Contrast (EXIT): OSD closes (SEL) (EXIT) Position (DOWN) (UP) (LEFT) / (RIGHT) / (UP) / (DOWN) (RESET): Reset Position [H. Position and V. Position] Continued on next page Data Sheet EN0512EJ1V0DS00 23 NL10276AC30-03L (DOWN) (UP) MENU Auto Adjust Brightness Clock Position Contrast (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) [S-Cnt Sel is ON] (SEL), (UP), (DOWN), (LEFT) / (RIGHT), (EXIT), (RESET) Contrast W R G B For details, see page 27, Initial Value Change Functions - 6. Sel Data. [S-Cnt Sel is OFF] (RIGHT), (UP) / (LEFT), (DOWN) Contrast W * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) Color Level W R G B Color Level W [S-Cnt Sel is ON] (SEL), (UP), (DOWN), (LEFT) / (RIGHT), (EXIT), (RESET) For details, see page 27, Initial Value Change Functions - 6. Sel Data. [S-Cnt Sel is OFF] (RIGHT), (UP) / (LEFT), (DOWN) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) (EXIT): OSD closes (SEL) (EXIT) Continued on next page 24 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (DOWN) (UP) (SEL) (EXIT) Information 1024 x 788 Hf 60.0 kHz Vf 75.0 Hz * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (DOWN) (UP) * MENU Color Level Information OSD Position Config All Reset (EXIT): OSD closes (SEL) (EXIT) (LEFT) / (RIGHT) / (UP) / (DOWN): OSD Position selects OSD Position Center Center/LeftUp/RightUp/ LeftDown/RightDown (SEL): Reset Position (SEL): Reset OSD Position (EXIT): OSD closes (SEL) (EXIT) (LEFT) / (LIGHT) / (UP) / (DOWN): Sync on Green select [ON/OFF] Sync on Green OFF (SEL): Reset Sync on Green (EXIT): OSD closes * Config is not indicated, when SoG Sel selected MENU "N" is selected (see Initial Value Change Functions - 6. Sel Data.) (SEL) (EXIT) All Reset No Yes (LEFT), (RIGHT), (UP), (DOWN) (EXIT) All Reset No (LEFT), (RIGHT), (UP), (DOWN) (SEL): Initialized Yes Notes: 1. The value of the selected signals of the LEFT, RIGHT, UP, and DOWN keys is continuously increased or decreased if the input signal is held for more than approximately one second. If it's held less than one second, the value is increased or decreased by one value. 2.y The RESET signal initializes the value selected by the SEL key. "All Reset" function initializes all the values. 3. No key input for more than ten seconds will be regarded as "time out". 4. Contrast W is synchronous with Contrast R, Contrast G, and Contrast B. 5. Color Level W is synchronous with Color Level R, Color Level G, and Color Level B. Data Sheet EN0512EJ1V0DS00 25 NL10276AC30-03L (c) Toggle type (SEL, UP, DOWN, and EXIT) (UP), (DOWN): + or - (EXIT): Initialize Start (SEL) (UP), (DOWN) (EXIT) (SEL) (UP), (DOWN) (EXIT) (SEL) (UP), (DOWN) (EXIT) (SEL) (UP), (DOWN) (EXIT) (SEL) (UP), (DOWN) (EXIT) (SEL) (UP), (DOWN) (EXIT) (SEL) All RESET Press Reset Key Over 2 Seconds (EXIT) (SEL) OSD closes Notes: 1. The value of the selected signals by the UP and DOWN key is continuously increased or decreased when the UP or DOWN key is pushed for more than about one second. 2.y The RESET signal initializes the value selected by the SEL key. The All Reset function initializes all the values. 3. No key input for more than five seconds will be regarded as "time out." 4. EXIT is connected to GND for more than approximately two seconds. 26 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (6) Initial Value Change Functions This module can change initial values, OSD items, and so on in customers. The changed initial value becomes the initial value in each preset timing, and is applicable when the value is reset too (including All Reset). * How to transpose to initial value change mode. Hierarchical type: Connect SET and UP to GND at the same time during the OSD function is "information". Toggle type: Connect SEL to GND while UP is connected to GND during the OSD function is "All Reset". * Operation SEL, UP, DOWN, and EXIT * How to return to normal mode Connect EXIT to GND or turn off the Power supply when OSD closes. Both LEDON and LEDOFF become "H" when this mode is operating. No. 1 Items Function items Compatible It becomes valid when the Toggle menu type only is selected. YES Sync on Green The initial value of contrast (RGB synchronous) becomes 128. NO: No Sync on Green The initial value of contrast (RGB synchronous) becomes 100. Initial value: NO 2 Brightness The maximum value of brightness of the backlight can be changed. Initial value: 100 3 Color Level The initial value of the color level can be changed. Initial value: 128 4 Contrast The initial value of contrast can be changed. Initial value: 128 (When NO is selected by Compatible in the toggle menu type, the initial value of RGB synchronous only is 100. As for RGB synchronous, this clause setup value becomes valid as the initial value regardless of the selection state of Compatible.) 5 LCD Data Note 1 Mode Number of page 13 PRESET TIMINGS is displayed. HSE The initial value of the Double Value can be changed. Delay The value of the CLK delay can be changed. (Initial value can not be changed.) Initial value: 0 VD The initial value of the up/down position of the display position can be changed. HD The initial value of the left/right position of the display position can be changed. Auto Adjust Par. Delay Note 2 Note 2 Par. HD Automatic adjustment The compensation value of Delay of the auto adjust can be changed. Valid range: 0 to 255 The compensation value of the horizontal position of the auto adjust can be changed. Valid range: 0 to 127 Continue to next page Data Sheet EN0512EJ1V0DS00 27 NL10276AC30-03L No. Form Function Items 5 LCD Data LCD Reset The values set in No. 5 LCD Data, are returned to the NEC factory values. 6 Sel Data S - Lvl Sel RGB individual adjustment can be made impossible in the adjustment of color level. In that case, the adjustment items are not displayed on the menu. ON : Individual adjustment is available. OFF : Individual adjustment is impossible Initial value: ON. S - Cnt Sel RGB individual adjustment can be made impossible in the adjustment of contrast. In that case, the adjustment items are not displayed on the menu. ON : Individual adjustment is available. OFF : Individual adjustment is impossible Initial value: ON. SOG Sel Select or nonselect of Sync on Green and display or nondisplay of the select menu can be selected. When nondisplay selected, Config is not displayed. * FUNC (Y: For Sync on Green select) (N: For Sync on Green nonselect) * MENU (Y: Select MENU display) (N: Select MENU nondisplay) Initial value (Y/N) * Effective only when the hierarchical menu type is selected. It becomes invalid when the toggle menu type is selected. MENU Sel Two kinds of B (Blue) and S (transparency) can be selected as the background color of the OSD menu. Initial value: B Button Sel 4 (SEL, UP, DOWN, and EXIT) or 7 (SEL, UP, DOWN, RIGHT, LEFT, EXIT, and RESET) as the numbers of the adjustment switches are selected. Initial value: 4 PSOSD Sel Display or no display for Power Save OSD can be selected. (For details, see page 29, Information Display by OSD) ON: Display Initial value: OFF OFF: No display 7 Information Input signal information is displayed. 8 OSD Position The initial value of the OSD display position can be changed. C: Center UL: Upper left UR: Upper right DL: Down left DR: Down right Initial value: C 9 Used Time * P. ON: Normal mode * P. OFF: Power saving mode Used time is recorded every five minutes. But it is not recorded when the power supply is cut off within five minutes. 10 Full Reset All values are returned to NEC factory values (default). It takes about seven seconds. Remark: Selected adjustment item is displayed with OSD. Remark: All adjustment values are returned to NEC factory values (default) when menu type is changed. Notes 1: * The values of No. 5 LCD Data are memorized in every preset timing. * Data except Auto Adjust of No. 5 LCD Data is saved at the moment when it is returned in the top menu. But it is not saved if the power supply is cut off before completion. It is saved after auto adjust is finished in case of the Auto Adjust. 2: Evaluate compensation value of Par. Delay and Par. HD of No. 5 LCD Data. 28 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L Flow chart of initial value change mode and OSD image Start (SEL): Main MENU open Compatible (EXIT): OSD closes Brightness Color Level Contrast (SEL) LCD Data Sel Data (EXIT) Compatible - No + Compatible mode selects (SEL)(RESET) (LEFT)(RIGHT)(UP)(DOWN) (LEFT)(RIGHT)(UP)(DOWN) (DOWN) (UP) (EXIT) Compatible - Yes + (SEL)(RESET) Reset Compatible No Yes (SEL)(EXIT) Reset compatible unselect (LEFT)(RIGHT)(UP)(DOWN) (LEFT)(RIGHT)(UP)(DOWN) Reset Compatible No Yes (SEL) Reset compatible unselect (EXIT) Reset compatible unselect Continued on next page Data Sheet EN0512EJ1V0DS00 29 NL10276AC30-03L (DOWN) (UP) (EXIT): OSD closes Compatible Brightness Color Level Contrast LCD Data Sel Data (SEL) (EXIT) Brightness Brightness value setting (UP)(RIGHT): Data increase (DOWN)(LEFT): Data decrease (DOWN) (UP) - 100 + (SEL)(RESET) Reset Brightness No (SEL)(RESET) Reset compatible unselect Yes (LEFT)(RIGHT)(UP)(DOWN) (LEFT)(RIGHT)(UP)(DOWN) Reset Brightness No Yes (EXIT) Reset compatible unselect (EXIT): OSD closes Compatible Brightness Color Level Contrast LCD Data Sel Data (SEL) R Level G Level B Level 128 128 128 (EXIT) Color level menu (SEL) (DOWN) (UP) (SEL) Reset compatible select (EXIT) Initial value setting of R Color Level (DOWN) (UP) R Color Level - 128 + (UP)(RIGHT): Data increase (DOWN)(LEFT): Data decrease (SEL)(RESET): The operation is the same as that operation of the Brightness screen. Continued on next page 30 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (DOWN) (UP) R Level G Level B Level 128 128 128 Color level menu (EXIT): To main menu (SEL) (EXIT) (DOWN) (UP) Initial value setting of G Color Level G Color Level (DOWN) (UP) - 128 + R Level G Level B Level 128 128 128 (UP)(RIGHT): Data increase (DOWN)(LEFT): Data decrease (SEL)(RESET): The operation is the same as that of the Brightness screen. Color level menu (EXIT): To main menu (SEL) (EXIT) Initial value setting of B Color Level B Color Level - 128 + (UP)(RIGHT): Data increase (DOWN)(LEFT): Data decrease (SEL)(RESET): The operation is the same as that of the Brightness screen. (EXIT): OSD closes Compatible Brightness Color Level Contrast LCD Data Sel Data (SEL) (EXIT) Contrast Sub Cnt.R Sub Cnt.G Sub Cnt.B 128 128 128 128 Contrast menu The next operation is the same as that of the Color level. (DOWN) (UP) Continued on next page Data Sheet EN0512EJ1V0DS00 31 NL10276AC30-03L (DOWN) (UP) (EXIT): OSD closes Compatible Brightness Color Level Contrast LCD Data Sel Data (SEL) Mode (DOWN) (UP) HSE Delay VD HD Auto Adjust (EXIT) 9 1344 0 34 290 Contrast menu The next operation is the same as that of the Color level. (DOWN) (UP) Mode HSE Delay VD HD Auto Adjust 9 1344 0 34 290 (SEL) (SEL)(EXIT) Auto Adjust screen Auto Adjust (DOWN) (UP) No Yes (LEFT)(RIGHT)(UP)(DOWN) (LEFT)(RIGHT)(UP)(DOWN) Auto Adjust No Par Delay Par HD LCD Reset 103 4 Yes (SEL) Auto Adjust select (EXIT) Auto Adjust unselect The continuation menu The next operation is the same as that of the Color level. (DOWN) (UP) Continued on next page 32 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (DOWN) (UP) (DOWN) (UP) Par.Delay Par.HD LCD Reset 103 4 (SEL) (SEL)(EXIT) LCD Reset screen LCD Reset No Yes (LEFT)(RIGHT)(UP)(DOWN) (LEFT)(RIGHT)(UP)(DOWN) (SEL) LCD Reset selects LCD Reset No (EXIT) LCD Reset unselect Yes (EXIT): OSD closes Compatible Brightness Color Level Contrast LCD Data Sel Data (SEL) (EXIT) (DOWN) (UP) S-Lv Sel ON S-Cnt Sel ON SOG Sel Y/N MENU Color B Button Sel 4 PSOSD Sel OFF Information OSD Position Used Time Full Reset SEL Data menu The next operation is the same as that of the Color level. (EXIT): OSD closes (SEL) (EXIT) (DOWN) (UP) Information Information screen 1024x768 Hf 48.4kHz Uf 60.1 Hz Continued on next page Data Sheet EN0512EJ1V0DS00 33 NL10276AC30-03L (DOWN) (UP) Information OSD Position Used Time Full Reset (EXIT): OSD closes (SEL) (EXIT) (DOWN) (UP) OSD Position - Information OSD Position Used Time Full Reset C + (EXIT): OSD closes (SEL) (EXIT) (DOWN) (UP) These information indicate the used time of LCD module. Used Time P.ON P.OFF Information OSD Position Used Time Full Reset OSD position select screen (UP)(RIGHT): The screen position moves in the center and the four corner of the display. (DOWN)(LEFT): The screen position returns to the position of before. (SEL)(RESET): The operation is the same as that of the Brightness screen. 198h30m 3h30m (EXIT): OSD closes (SEL) Full Reset No (SEL)(EXIT) Full reset screen Yes Full Reset (SEL) Full reset select No (EXIT) Full reset unselect Yes Remark: There is no Time out in the OSD function. 34 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (7) Information Display by OSD (a) Power save: The frequency of horizontal and vertical synchronous signal is displayed for four seconds at a Power Save mode switchover. Power Save Hf 0.0 kHz Vf 0.0 Hz * It is displayed when the horizontal synchronous signal frequency (Hf) and vertical synchronous signal frequency (Vf) are as follows: (1) Hf < 10 KHz (2) Vf < 40 Hz (3) (1) and (2) * It is not displayed when the "Power Save OSD no display" form is selected (See page 27, Initial Value Change Functions 6. Sel Data, PSOSD Sel). (b) Out of Range: Each frequency is displayed for four seconds when the horizontal or vertical synchronous signal is off from the corresponding range. Out of Range Hf 64.0 kHz Vf 60.0 Hz * It is displayed when the horizontal synchronous signal frequency (Hf) and vertical synchronous signal frequency (Vf) are as follows: (1) 10 KHz Hf < 23 KHz or 61.5 KHz < Hf (2) 40 Hz Vf < 50 Hz or 200 Hz < Vf (3) (1) and (2) either Hf or Vf is in It is not displayed when Power Save mode. * Display or no display for Out of Range cannot be selected. (c) Disable: It is displayed for four seconds that the switches for adjustment are disabled. Key Disable Data Sheet EN0512EJ1V0DS00 35 NL10276AC30-03L (8) Input Signal and Display Position - XGA Standard Timing Pixels D (0, 0) D (1, 0) D (2, 0) *** *** D (1023, 0) D (1, 1) D 2, 1) *** *** D (1023, 1) D (0, 2) D (1, 2) D (2, 2) *** *** D (1023, 2) * * * * * * * * * * * * D (0, 767) D (1, 767) D (2, 767) D (0, 1) * * * * V Pulse *** *** V B. Porch Vsync 1 line Hsync XGA mode (VD = "35") 0 1 R G B 2 3 4 5 *** 35 Invalid 36 37 Valid D (0, X), D (1, X), D (2, X) H Pulse H B. Porch Hsync 1 clk CLK XGA mode (HD = "296") 0 1 2 3 4 5 *** 296 297 298 tda R G B Invalid Valid D (X, 0), D (X, 1), D (X, 2) Note: The tda should be more than 4 ns. 36 Data Sheet EN0512EJ1V0DS00 D (1023, 767) NL10276AC30-03L OPTICAL CHARACTERISTICS (Ta = 25C, VDD = 12 V, VDDB = 12 V, Note 1) Item Symbol Condition Min. Typ. Max. Unit Remark CR = 2.2 viewing angle x+ = 0, x- = 0, y- = 0, White/Black, at center 80 250 - - Note 2 Lumax White, at center 220 350 - cd/m - White - - 1.30 - Symbol Condition Min. Typ. Max. Unit Remark Contrast ratio CR Best contrast angle x+ = 0, x- = 0, y- = 5 White/Black, at center - 300 - - Note 2 Color gamut C x+ = 0, x- = 0, y+ = 0, y- = 0 at center, to NTSC 35 40 - % - x+ CR > 10, White/Black y = 0 50 55 - deg. Note 5 50 55 - deg. CR > 10, White/Black x = 0 35 45 - deg. 30 45 - deg. Ton White (100%) to Black (10%) - 15 40 ms Note 6 Toff Black (0%) to White (90%) - 40 50 - Maximum luminance: 100% - 20 to 100 - % - Contrast ratio Luminance Luminance uniformity 2 Note 3 Note 4 Reference data (Ta = 25C, VDD = 12 V, VDDB = 12 V, Note 1) Item Viewing angle range x- y+ y- Response time Luminance control range Notes: 1. The luminance is measured after the module has been working for 20 minutes, with all pixels in white. The typical value is measured after luminance saturation. Display mode: VESA XGA-75 Hz RGB input voltage: 0.7 V p-p Contrast level: Default (128) 2. The contrast ratio is calculated by using the following formula. Contrast ratio (CR) = Luminance with all pixels in white Luminance with all pixels in black 3. The luminance is measured after the module has been working for 20 minutes, with all pixels in white. The typical value is measured after luminance saturation, more than one hour after powered-on. The timing is SXGA standard mode, preset No. 9. 50 cm Photodetector (TOPCON BM5-A) 1 LCD module Data Sheet EN0512EJ1V0DS00 37 NL10276AC30-03L 4. Luminance uniformity is calculated by using the following formula. Maximum luminance Luminance uniformity = Minimum luminance The luminance is measured at or near the five points shown below. Column 171 512 1 853 2 128 Row 3 4 384 5 640 5. Definitions of viewing angles are as follows. Perpendicular 12 o'clock x- y+ Left Upper x+ y- Right Lower 6. Definitions of response time is as follows. The photodetector output signal is measured when the luminance changes from white to black or from black to white. White 100% 90% Luminance range Black 10% 0% Ton 38 Toff Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L RELIABILITY TESTS Test item Test conditions Judgment High temperature/humidity operation 50 2C, RH = 85% 240 hours; Display data is black. Note 1 Heat cycle (operation) <1> 0C 3C 1 hour 55C 3C 1 hour <2> 50 cycles, 4 hours/cycle <3> Display data is black. Note 1 Thermal shock (nonoperation) <1> -20C 3C 30 minutes 60C 3C 30 minutes <2> 100 cycles <3> Temperature transition time is within 5 minutes. Note 1 Vibration (nonoperation) <1> 5-100 Hz, 19.6 m/s (2G) <2> 1 minute/cycle, X, Y, Z direction <3> 50 times each direction Mechanical shock (nonoperation) <1> 294 m/s (30G), 11 ms X, Y, Z direction <2> 3 times each direction Notes 1, 2 ESD (operation) 150 pF, 150 , 10 KV 9 places on a panel 10 times each place at one-second intervals Note 1 15 kinds of dust (JIS-Z 8901) Hourly 15 seconds stir, 8 times repeat Note 1 Dust (operation) 2 2 Notes 1, 2 Note 3 Notes: 1. Display function is checked by the same condition as the LCD module outgoing inspection. 2. Physical damage. 3. Discharge points are shown in the following figure. Data Sheet EN0512EJ1V0DS00 39 NL10276AC30-03L GENERAL CAUTIONS Because the following figures and statements are very important, please be sure you understand their contents completely. CAUTION This figure is a warning that you will get hurt and/or the module will be damaged if you make a mistake in operation. This figure is a warning that you will get an electric shock if you make a mistake in operation. This figure is a warning that you will get hurt if you make a mistake in operation. CAUTION Do not touch an inverter on which there is a caution label while the LCD module is in operation, because of dangerous high voltage. (1) Caution when taking out the module Pick up the pouch only, when removing the module from a carrier box. (2) Cautions for handling the module a) As the electrostatic discharges may break the LCD module, handle the LCD module with care against electrostaic discharges. b) As the LCD panel and backlight element are made from fragile glass material, impulse and c) As the surface of polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for pressure to the LCD module should be avoided. cleaning. d) Do not pull the interface connectors in or out while the LCD module is operating. e) Put the module display side down on a flat horizontal plane. f) Handle connectors and cables with care. g)y The torque to mounting screw should never exceed 0.392 N*m (4 kgf*cm). h)y Do not give the stress to interface connectors. The module may become function deficiency by a contact defective and damages. Pay attention to handling at the time of matching connector connection and in the connection condition. (3) Cautions regarding atmosphere a) Dew drop atmosphere should be avoided. b) Do not store and/or operate the LCD module in a high-temperature and/or high-humidity atmosphere. Storage in an electro-conductive polymer packing pouch and in a relatively low-temperature atmosphere is recommended. c) This module uses cold cathode fluorescent lamps. The life time of the lamps is shortened conspicuously at low temperatures. d) Do not operate the LCD module in high magnetic field. (4) Cautions about the module characteristics a) Do not apply a fixed pattern data signals to theLCD module at product aging. Applying a fixed pattern for a long time may cause image sticking. 40 Data Sheet EN0512EJ1V0DS00 NL10276AC30-03L (5) Other cautions a) Do not disassemble and/or reassemble the LCD module. b) Do not readjust variable resistor or switch, etc. c) When returning the module for repair, etc., please pack the module so it will not be broken. We recommend using the original shipping packages. The liquid crystal display has the following specific characteristics. These are neither defects nor malfunctions. The display condition of the LCD module may be affected by the ambient temperature. The LCD module has cold cathode tube for backlight. Optical characteristics, like luminance or uniformity, will change over time. Uneven brightness and/or small spots may be noticed, depending on different display patterns. Data Sheet EN0512EJ1V0DS00 41 MAX 23.5 TYP 22.5 15.6 0.3 4 -2.7 0.3 2 5 0.3 5 0.2 4 2 10 0.3 2 3 304.128 (ACTIVE AREA) 2 6 0.3 4 -3.4 0.3 OUTLINE DRAWINGS 340 0.3 308.8 0.3 (BEZEL OPENING) Front View (Unit in mm) 42 350 0.6 2 2 4 - 3.5 0.1 6 0.3 265 0.6 212 0.3 232.7 0.3 (BEZEL OPENING) 197 97.8 0.7 204 0.3 DETAIL A DETAIL B 2 5 2 SEC B-B DETAIL B 6 0.3 31 0.3 5 0.3 B 2 SEC A-A DETAIL A 5.1 0.2 3.1 +0.2 -0 0.4 0.2 * The torque for mounting screws should never exceed 0.392 N*m (4 Kg*cm). * Tolerances of dimensions not shown is 0.5 mm. 4.5 0.2 3.1 +0.2 -0 2 0.4 0.2 5 0.3 2 6 0.3 B A NL10276AC30-03L A 18.6 0.3 8 -R4.4 8 0.2 5 2 Data Sheet EN0512EJ1V0DS00 ACTIVE AREA CENTER 228.096 (ACTIVE AREA) 170 0.7 9.5 171.2 Max23.5 TYP22.5 4-3.4 0.3 4-2.7 0.3 62.8 1 130.6 1 31 Printed Circuit Board FPC 6.2 54 US 0.3 Inverter 6.7 81.1 153 1 126.1 1 199 1 231 14 CN3 65 A 1 8 CN5 0.3 A A 35.7 A 0 C 3 L 13.5 5 0 A 7 6 3 14.7 22 Material Information Light guide:>PMMA< 0 59 1 1.5 A 1 0 53 43 DETAIL A 20 104 80 11.8 16 104 5.5 8.3 4.3 1.6 16 13.4 42 * The torque for mounting screws should never exceed 0.392 N*m (4 Kg*cm). * Tolerances of the dimensions not shown are 0.5 mm. 13.8 16 20 8.5 4 7.9 9 6 7.6 1 78 CN201 11 THE TFT COLOR LCD PANEL CONTAINS COLD CATHODE FLOURESCENT LAMPS. PLEASE FOLLOW LOCAL ORDINANCES OR REGULATIONS FOR ITS DISPOSAL 108.7 1 27.8 1 32.7 1 233 1 45 223.8 139.8 1 130 138 see DETAIL A NL10276AC30-03L 29 Data Sheet EN0512EJ1V0DS00 CAUTION 7.6 13.9 C MADE IN JAPAN 85 00. 4. 10/ E170632 2.2 14 CN1 1 20 SERIAL: B0410036* PANEL: A100892018301 54.5 1 5 48.6 MODEL NL10276BC30-04D 9.7 13.5 4 7.5 24 C Max23.5 TYP22.5 Rear View (Unit in mm) 15.7 1/iieaec$&eiie/ No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its e l e c t r o n i c components, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC electronic component, customers must incorporate sufficient safety measures in its design, such as redundancy, firecontainment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard," "Special," and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific a p p l i c a t i o n . T h e r e c o m m e n d e d applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical e q u i p m e n t ( n o t specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. (Note) (1) "NEC" as used in this statement means NEC Corporation and also includes its majorityowned subsidiaries. (2) "NEC electronic component products" means any electronic component product developed or manufactured by or for NEC (as defined above). DATA SHEET DE0202