PATENT NUMBERS
5713755 / 5961339
DO NOT
SCALE FROM
THIS PRINT
"A"
"A"
RHLE-50-D
No OF POS x .100 [2.54]
.200
REF
5.08
.020
REF
0.51
.100
REF
2.54
2
MAX SWAY
({No of POS - 1} x .100 [2.54])
.005 [.13]
C-132-12-XXX
+.008 [.20]
-.005 [.13]
01
C1
.144 3.66
.259 6.57
90°
±3°
.146 3.70
SECTION "A"-"A"
C7
C8
.008 x .056 REF
[.20 x 1.42]
.0625 1.588
.050 1.27 .050 1.27
(No OF POS x .1000) - .2000
[2.540] [5.080]
SM-A10H
LC-08-TM-01
C4
-A & -LC OPTION
FIGURE 2
C5
"R"
.152 3.86
"S"
.225 5.72
MPP-02
FIGURE 3
(-P: PICK AND PLACE PAD)
AVAILABLE ON POSITIONS 03 THRU 50
NOTE: "R" = USE MEASURED DIM (REF)
"S" = {("R" - .225 [5.72])/2}
.020 [.51]
C2
C10
.2559 6.500
.028
±.010
[.71
.25]
"S"
(SEE NOTE)
"R" (SEE NOTE)
K-500-300
FIGURE 4
-K: POLYMIDE FILM PAD
AVAILABLE ON POS 03 THRU 50
NOTE: "R" = USE MEASURED DIM (REF)
"S" = {("R" - .2559 [6.500])/2}
.020 [.51]
.280 7.11
.149 3.78
C9
HLE-1XX-02-XXX-DV-XX-XX-XX
No OF POSITIONS
-02 THRU -50
(PER ROW)
ROW SPECIFICATION
-DV: DOUBLE VERTICAL
(USE RHLE-50-D)
LEAD STYLE
-02: SURFACE MOUNT
(USE C-132-12-X)
PLATING SPECIFICATION
-G: GOLD (USE C-132-12-G)
-S: SELECTIVE GOLD
(USE C-132-12-S)
-F: SELECTIVE FLASH GOLD
(USE C-132-12-F)
-L: SELECTIVE LIGHT GOLD
(USE C-132-12-L)
-H: HEAVY GOLD
(USE C-132-12-H)
-STL: SELECTIVE TIN/LEAD
(USE C-132-12-STL)
-SM SELECTIVE GOLD/MATTE TIN TAIL
(USE C-132-12-S)
-FM SELECTIVE FLASH GOLD/MATTE TIN TAIL
(USE C-132-12-F)
-LM LIGHT GOLD/MATTE TIN TAIL
(USE C-132-12-L)
OPTION
-TR: TAPE & REEL
(2 - 29 POSITIONS ONLY)
OPTION
-P: PICK & PLACE PAD
(POS -03 THRU -50 ONLY)
-A: ALIGNMENT PIN (4 POS MIN)
-LC: LOCKING CLIP (2 POS MIN)
-K: POLYAMIDE FILM PAD (AVAILABLE
ON POS -03 THRU -50; .005 [.13]
THICKNESS WITH SILICONE ADHESIVE)
(SEE FIG. 1)
OPTION
-BE: BOTTOM ENTRY
(USE RHLE-50-DBE)(SEE FIG. 5)
(LEAVE BLANK FOR STANDARD)
FIGURE 5
-BE OPTION
(SAME AS FIG. 1 UNLESS OTHERWISE STATED)
RHLE-50-DBE
TUBE VIEWS
PT-1-24-01-64
PT-1-24-10-63
SEE TABLE 2
FIGURE 1
HLE-116-02-XXX-DV SHOWN
C6
C3
C
02
AC
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 3
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
[2.54] .100 TIGER BEAM SOCKET ASSEMBLY
BY:
HLE-1XX-02-XXX-DV-XX-XX-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
ED MESSER
12/19/98
1
1
SHEET SCALE: 1:1
BODY: VECTRA E130i
CONTACT: BeCu
c:\enterprisevault\DWG\MISC\MKTG\HLE-1XX-02-XXX-DV-XX-XX-XX-MKT.SLDDRW
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.
2. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 [.05]
OFF THE SURFACE OF THE PART.
3. PULL OUT FORCE FOR -LC, -A, & CONTACT IS 12 oz MIN.
4. COPLANARITY: SEE TABLE 2.
5. BURR ALLOWANCE: .003 [.08] MAX
6. CUT ASSEMBLIES AFTER FILL. CUT FLASH TO BE .010 MAX WITH NO FLASH
ALLOWED IN HOLES OR EXTENDING BELOW LEADS. WILL LOSE A POSITION
FOR EVERY CUT MADE ON A SOCKET STRIP.
7. TUBE POSITIONS 03 THRU 50. LAYER PACKAGE POSITION 02.
8. ENDWALL THICKNESS: .030+/-.005[.76+/-.13] TO BE MEASURED FROM BOTTOM VIEW.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail: info@SAMTEC.com code: 55322
REVISION AC
