MAX6897PALT+T - Maxim Integrated

General Description

The MAX6895–MAX6899 is a family of small, low-pow-

er, voltage-monitoring circuits with sequencing

capability. These miniature devices offer tremendous

flexibility with an adjustable threshold capable of monitor-

ing down to 0.5V and an external capacitor-adjustable time

delay. These devices are ideal for use in power-supply

sequencing, reset sequencing, and power-switching

applications. Multiple devices can be cascaded for complex

sequencing applications.

A high-impedance input with a 0.5V threshold allows an

external resistive divider to set the monitored threshold.

The output asserts (OUT = high or OUT = low) when

the input voltage rises above the 0.5V threshold and

the enable input is asserted (ENABLE = high or

ENABLE = low). When the voltage at the input falls

below 0.5V or when the enable input is deassert-

ed (ENABLE = low or ENABLE = high), the output

deasserts (OUT = low or OUT = high). All devices

provide a capacitor-programmable delay time from when

the input rises above 0.5V to when the output is assert-

ed. The MAX689_A versions provide the same capaci-

tor-adjustable delay from when enable is asserted to

when the output asserts. The MAX689_P devices have

a 1µs propagation delay from when enable is asserted

to when the output asserts.

The MAX6895A/P offers an active-high enable input

and an active-high push-pull output. The MAX6896A/P

offers an active-low enable input and an active-low

push-pull output. The MAX6897A/P offers an active-

high enable input and an active-high open-drain

out-put. Finally, the MAX6898A/P offers an active-low

enable input and an active-low open-drain output. The

MAX6899A/P offers an active-low enable with an active-

high push-pull output.

All devices operate from a 1.5V to 5.5V supply volt-

age and are fully specified over the -40°C to +125°C

operating temperature range. These devices are

available in ultra-small 6-pin µDFN (1.0mm x 1.5mm) and

thin SOT23 (1.60mm x 2.90mm) packages.

Applications

Features

●1.8% Accurate Adjustable Threshold Over

Temperature

● Operate from VCC of 1.5V to 5.5V

● Capacitor-Adjustable Delay

● Active-High/-Low Enable Input Options

● Active-High/-Low Output Options

● Open-Drain (28V Tolerant)/Push-Pull Output

Options

● Low Supply Current (10µA, typ)

● Fully Specified from -40°C to +125°C

● Ultra-Small 6-Pin µDFN Package or Thin SOT23

Package

●Automotive

●Medical Equipment

●Intelligent Instruments

●Portable Equipment

●Computers/Servers

●Critical µP Monitoring

●Set-Top Boxes

●Telecom

19-3673; Rev 10; 3/14

Note: All devices are specified over the -40°C to +125°C

operating temperature range.

+Denotes a lead(Pb)-free/RoHS-compliant package.

/V denotes an automotive qualified part; T = Tape and reel.

Typical Operating Circuit and Selector Guide appear at end

of data sheet.

Ordering Information continued at end of data sheet.

Pin Configurations continued at end of data sheet.

PART PIN-PACKAGE TOP MARK

MAX6895AALT+ 6 µDFN +AW

MAX6895AAZT+ 6 Thin SOT23 +AADK

MAX6895PALT+T 6 µDFN +AX

MAX6895PAZT+ 6 Thin SOT23 +AADL

MAX6896AALT+ 6 µDFN +AY

MAX6896AAZT+ 6 Thin SOT23 +AADO

MAX6896AAZT/V+T 6 Thin SOT23 +AATA

MAX6896PALT+T 6 µDFN +AZ

MAX6896PAZT+ 6 Thin SOT23 +AADP

MAX6896PAZT/V+T 6 Thin SOT23 —

1 2 3

6 5 4

OUT

( ) FOR MAX6899 ONLY.

VCC CDELAY

ENABLE

(ENABLE)

INGND

MAX6895

MAX6897

MAX6899

µDFN

TOP VIEW

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Pin Congurations

Ordering Information

µDFN

Junction-to-Ambient Thermal Resistance (θJA)......... 477°C/W

Junction-to-Case Thermal Resistance (θJC)................122C/W

Thin SOT23

Junction-to-Ambient Thermal Resistance (θJA)..........110°C/W

Junction-to-Case Thermal Resistance (θJC).................50°C/W

VCC, ENABLE, ENABLE, IN ...................................-0.3V to +6V

OUT, OUT (push-pull) ............................... -0.3V to (VCC + 0.3V)

OUT, OUT (open-drain) .........................................-0.3V to +30V

CDELAY ................................................... -0.3V to (VCC + 0.3V)

Output Current (all pins) ................................................... ±20mA

Continuous Power Dissipation (TA = +70°C)

6-Pin µDFN (derate 2.1mW/°C above +70°C) .........167.7mW

6-Pin Thin SOT23 (derate 9.1mW/°C above +70°C) ....727.3mW

Operating Temperature Range ......................... -40°C to +125°C

Storage Temperature Range ............................ -65°C to +150°C

Junction Temperature ...................................................... +150°C

Lead Temperature (soldering, 10s) .................................+300°C

Soldering Temperature (reflow) .......................................+260°C

(VCC = 1.5V to 5.5V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V and TA = +25°C, unless

otherwise noted.) (Note 2)

Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four layer

board. For detailed information on package thermal considerations refer to www.maximintegrated.com/thermal-tutorial.

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

SUPPLY

Operating Voltage Range VCC 1.5 5.5 V

Undervoltage Lockout (Note 3) UVLO VCC falling 1.20 1.35 V

VCC Supply Current ICC VCC = 3.3V, no load 10 20 µA

Threshold Voltage VTH VIN rising, 1.5V < VCC < 5.5V 0.491 0.5 0.509 V

Hysteresis VHYST VIN falling 5 mV

Input Current (Note 4) IIN VIN = 0V or VCC -15 +15 nA

CDELAY

Delay Charge Current ICD 200 250 300 nA

Delay Threshold VTCD CDELAY rising 0.95 1.00 1.05 V

CDELAY Pulldown Resistance RCDELAY 130 500 Ω

ENABLE/ENABLE

Input Low Voltage VIL 0.4 V

Input High Voltage VIH 1.4 V

Input Leakage Current ILEAK ENABLE, ENABLE = VCC or GND -100 +100 nA

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Electrical Characteristics

Package Thermal Characteristics (Note 1)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these

or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect

device reliability.

Absolute Maximum Ratings

Note 2: All devices are production tested at TA = +25°C. Limits over temperature are guaranteed by design.

Note 3: When VCC falls below the UVLO threshold, the outputs will deassert (OUT goes low, OUT goes high). When VCC falls

below 1.2V, the out cannot be determined.

Note 4: Guaranteed by design.

Note 5: During the initial power-up, VCC must exceed 1.5V for at least 2ms before the output is guaranteed to be in the correct

state.

(VCC = 1.5V to 5.5V, TA = -40°C to +125°C, unless otherwise specified. Typical values are at VCC = 3.3V and TA = +25°C, unless

otherwise noted.) (Note 2)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

OUT/OUT

Output Low Voltage (Open-Drain

or Push-Pull) VOL

VCC ≥ 1.2V, ISINK = 90µA,

MAX6895/MAX6897/MAX6899 only 0.3

VCC ≥ 2.25V, ISINK = 0.5mA 0.3

VCC ≥ 4.5V, ISINK = 1mA 0.4

Output High Voltage (Push-Pull) VOH

VCC ≥ 2.25V, ISOURCE = 500µA 0.8 x

VCC V

VCC ≥ 4.5V, ISOURCE = 800µA 0.8 x

VCC

Output Open-Drain Leakage

Current ILKG Output high impedance, VOUT = 28V 1 µA

TIMING

IN to OUT/OUT Propagation

Delay

tDELAY VIN rising CCDELAY = 0µF 40 µs

CCDELAY = 0.047µF 190 ms

tDL VIN falling 16 µs

Startup Delay (Note 5) 2 ms

ENABLE/ENABLE Minimum

Input Pulse Width tPW 1 µs

ENABLE/ENABLE Glitch

Rejection 100 ns

ENABLE/ENABLE to OUT/OUT

Delay tOFF From device enabled to device disabled 150 ns

ENABLE/ENABLE to OUT/OUT

Delay

tPROPP From device disabled to device enabled

(P version) 150 ns

tPROPA

From device disabled

to device enabled

(A version)

CCDELAY = 0µF 20 µs

CCDELAY = 0.047µF 190 ms

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Electrical Characteristics (continued)

(VCC = 3.3V and TA = +25°C, unless otherwise noted.)

ENABLE TURN-ON/OFF DELAY

(MAX6895A)

MAX6895 toc09

40µs/div

OUT

2V/div

ENABLE

2V/div

ENABLE TURN-ON/OFF

(MAX6896P)

MAX6895 toc08

100ns/div

VOUT

2V/div

VENABLE

2V/div

MAXIMUM TRANSIENT DURATION

vs. INPUT OVERDRIVE

MAX6895 toc07

VOVERDRIVE (mV)

MAXIMUM TRANSIENT DURATION (µs)

908070605040302010

100

200

300

400

500

600

0 100

RESET

OCCURS

OUTPUT HIGH VOLTAGE

vs. SOURCE CURRENT

MAX6895 toc06

ISOURCE (mA)

VOH (V)

181612 144 6 8 102

0.5

1.0

1.5

2.0

2.5

3.0

3.5

4.0

4.5

5.0

0 20

VCC = 5V

VCC = 3V

VCC = 1.5V

OUTPUT LOW VOLTAGE

vs. SINK CURRENT

MAX6895 toc05

ISINK (mA)

VOL (V)

5.55.04.54.03.53.02.52.01.51.00.5

0.3

0.6

0.9

1.2

1.5

0 6.0

VCC = 5V

VCC = 3V

VCC = 1.5V

OUT DELAY

vs. CCDELAY

MAX6895 toc04

CCDELAY (nF)

tDELAY (ms)

900800600 700200 300 400 500100

500

1000

1500

2000

2500

3000

3500

4000

4500

5000

0 1000

IN THRESHOLD

vs. TEMPERATURE

MAX6895 toc03

TEMPERATURE (C)

VTH (V)

1109565 80-10 5 20 35 50-25

0.4992

0.4994

0.4996

0.4998

0.5000

0.5002

0.5004

0.5006

0.5008

0.5010

0.4990

-40 125

SUPPLY CURRENT

vs. TEMPERATURE

MAX6895 toc02

TEMPERATURE (°C)

ICC (µA)

1109565 80-10 5 20 35 50-25

-40 125

VCC = 5V

VCC = 3V

VCC = 1.5V

SUPPLY CURRENT

vs. SUPPLY VOLTAGE

MAX6895 toc01

VCC (V)

ICC (µA)

5.04.53.5 4.01.0 1.5 2.0 2.5 3.00.5

0 5.5

Maxim Integrated

│

www.maximintegrated.com

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Typical Operating Characteristics

NAME FUNCTION

MAX6895/

MAX6897

MAX6896/

MAX6898 MAX6899

µDFN THIN

SOT23 µDFN THIN

SOT23

1 1 — — — — ENABLE

Active-High Logic-Enable Input. Drive ENABLE low to

immediately deassert the output to its false state (OUT =

low or OUT = high) independent of VIN. With VIN above

VTH, drive ENABLE high to assert the output to its true

state (OUT = high or OUT = low) after the adjustable

delay period (MAX689_A) or a 150ns propagation delay

(MAX689_P).

— — 1 1 1 1 ENABLE

Active-Low Logic-Enable Input. Drive ENABLE high to

immediately deassert the output to its false state (OUT =

low or OUT = high) independent of VIN. With VIN above

VTH, drive ENABLE low to assert the output to its true

state (OUT = high or OUT = low) after the adjustable

delay period (MAX689_A) or a 150ns propagation delay

(MAX689_P).

2 2 2 2 2 2 GND Ground

333333 IN

High-Impedance Monitor Input. Connect IN to an

external resistive divider to set the desired monitored

threshold. The output changes state when VIN rises

above 0.5V and when VIN falls below 0.495V.

4 4 — — 4 4 OUT

Active-High Sequencer/Monitor Output, Push-Pull

(MAX6895/MAX6899) or Open-Drain (MAX6897). OUT

is asserted to its true state (OUT = high) when VIN

is above VTH and the enable input is in its true state

(ENABLE = high or ENABLE = low) for the capacitor-

adjusted delay period. OUT is deasserted to its false

state (OUT = low) immediately after VIN drops below

VTH - 5mV or the enable input is in its false state

(ENABLE = low or ENABLE = high). The open-drain

version requires an external pullup resistor.

— — 4 4 — — OUT

Active-Low Sequencer/Monitor Output, Push-Pull

(MAX6896) or Open-Drain (MAX6898). OUT is asserted

to its true state (OUT = low) when VIN is above VTH

and the enable input is in its true state (ENABLE = high

or ENABLE = low) after the CDELAY adjusted timeout

period. OUT is deasserted to its false state (OUT =

high) immediately after VIN drops below VTH - 5mV or

the enable input is in its false state (ENABLE = low or

ENABLE = high). The open-drain version requires an

external pullup resistor.

5 6 5 6 5 6 CDELAY

Capacitor-Adjustable Delay. Connect an external

capacitor (CCDELAY) from CDELAY to GND to set the

IN to OUT (and ENABLE to OUT or ENABLE to OUT

for A version devices) delay period. tDELAY = (CCDELAY

x 4.0 x 106) + 40µs. There is a fixed short delay (40µs,

typ) for the output deasserting when VIN falls below

VTH.

656565 VCC

Supply Voltage Input. Connect a 1.5V to 5.5V supply

to VCC to power the device. For noisy systems, bypass

with a 0.1µF ceramic capacitor to GND.

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Pin Description

Detailed Description

The MAX6895–MAX6899 is a family of ultra-small, low-

power, sequencing/supervisory circuits. These devices

provide adjustable voltage monitoring for inputs down to

0.5V. They are ideal for use in power-supply sequenc-

ing, reset sequencing, and power-switching applica-

tions. Multiple devices can be cascaded for complex

sequencing applications.

Voltage monitoring is performed through a high-imped-

ance input (IN) with an internally fixed 0.5V threshold.

When the voltage at IN falls below 0.5V or when the

enable input is deasserted (ENABLE = low or ENABLE =

high), the output deasserts (OUT goes low or OUT goes

high). When VIN rises above 0.5V and the enable input is

asserted (ENABLE = high or ENABLE = low), the output

asserts (OUT goes high or OUT goes low) after a capaci-

tor-programmable time delay.

With VIN above 0.5V, the enable input can be used to

turn the output on or off. After the enable input is assert-

ed, the output turns on with a capacitor-programmable

delay period (A version) or with a 150ns propagation

delay (P version). Tables 1, 2, and 3 detail the out-

put state depending on the various input and enable

conditions.

Supply Input (VCC)

The device operates with a VCC supply voltage from

1.5V to 5.5V. To maintain a 1.8% accurate threshold,

VCC must be above 1.5V. When VCC falls below the

UVLO threshold, the output deasserts. When VCC falls

below 1.2V the output state cannot be determined. For

noisy systems, connect a 0.1µF ceramic capacitor from

VCC to GND as close to the device as possible. For the

push-pull active-high output option, a 100kΩ external

pulldown resistor to ground ensures the correct logic

state for VCC down to 0.

Table 3. MAX6899 Output

Table 2. MAX6896/MAX6898 Output

Table 1. MAX6895/MAX6897 Output

Figure 1. MAX6895/MAX6899 Functional Diagram

IN ENABLE OUT

VIN < VTH Low Low

VIN < VTH High Low

VIN > VTH Low High

VIN > VTH High Low

IN ENABLE OUT

VIN < VTH Low

OUT = VCC (MAX6896)

OUT = high impedance

(MAX6898)

VIN < VTH High

OUT = VCC (MAX6896)

OUT = high impedance

(MAX6898)

VIN > VTH Low Low

VIN > VTH High

OUT = VCC (MAX6896)

OUT = high impedance

(MAX6898)

IN ENABLE OUT

VIN < VTH Low Low

VIN < VTH High Low

VIN > VTH Low Low

VIN > VTH High

OUT = VCC

(MAX6895)

OUT = high

Impedance

(MAX6897)

MAX6895

MAX6899

LOGIC

1.0V

250nA

0.5V

OUT

CDELAY GND

ENABLE (MAX6895)

ENABLE (MAX6899) VCC

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Monitor Input (IN)

Connect the center point of a resistive divider to IN to

monitor external voltages (see R1 and R2 of the Typical

Operating Circuit). IN has a rising threshold of VTH =

0.5V and a falling threshold of 0.495V (5mV hysteresis).

When VIN rises above VTH and ENABLE is high (or

ENABLE is low) OUT goes high (OUT goes low) after

the programmed tDELAY period. When VIN falls below

0.495V, OUT goes low (OUT goes high) after a 16µs

delay. IN has a maximum input current of 15nA so

large-value resistors are permitted without adding sig-

nificant error to the resistive divider.

Adjustable Delay (CDELAY)

When VIN rises above VTH with ENABLE high (ENABLE

low), the internal 250nA current source begins charging

an external capacitor connected from CDELAY to GND.

When the voltage at CDELAY reaches 1V, the output

asserts (OUT goes high or OUT goes low). When the

output asserts, CCDELAY is immediately discharged.

Adjust the delay (tDELAY) from when VIN rises above

VTH (with ENABLE high or ENABLE low) to OUT going

high (OUT going low) according to the equation:

tDELAY = CCDELAY x 4.0 x 106 + 40µs

where CCDELAY is the external capacitor from CDELAY

to GND.

For adjustable delay devices (A version), when VIN >

0.5V and ENABLE goes from low to high (ENABLE

goes from high to low) the output asserts after a tDELAY

period. For nonadjustable delay devices (P version)

there is a 1µs propagation delay from when the enable

input is asserted to when the output asserts. Figures 2

through 5 show the timing diagrams for the adjustable and

fixed delay versions, respectively.

Figure 2. MAX6895A/MAX6897A Timing Diagram

VCC

VUVLO

VTH VTH

tPROPA

tDL tOFF

tDELAY

t < tPROPA

tPROPA

ENABLE

OUT

t > tPW

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Figure 4. MAX6895P/MAX6897P Timing Diagram

Figure 3. MAX6896A/MAX6898A Timing Diagram

VCC

VUVLO

tPROPP tDL tOFF

tDELAY

t > tPW

tPROPP

ENABLE

OUT

VCC

VUVLO

tPROPA

tDL tOFF

tDELAY

t < tPROPA

tPROPA

ENABLE

OUT

t > tPW

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Figure 6. MAX6899A Timing Diagram

Figure 5. MAX6896P/MAX6898P Timing Diagram

VCC

VUVLO

VTH VTH

tPROPA

tDL tOFF

tDELAY

t < tPROPA

tPROPA

ENABLE

OUT

t > tPW

VCC

VUVLO

tPROPP tDL tOFF

tDELAY

t > tPW

tPROPP

ENABLE

OUT

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Enable Input (ENABLE or ENABLE)

The MAX6895/MAX6897 offer an active-high enable input

(ENABLE), while the MAX6896/MAX6898/MAX6899 offer

an active-low enable input (ENABLE). With VIN above

VTH, drive ENABLE high (ENABLE low) to force OUT high

(OUT low) after the adjustable delay time (A versions).

For P version devices, when VIN > 0.5V and enable is

asserted, the output asserts after typically 150ns.

The enable input has logic-high and logic-low voltage

thresholds of 1.4V and 0.4V, respectively. For both ver-

sions, when VIN > 0.5V, drive ENABLE low (ENABLE

high) to force OUT low (OUT high) within 150ns typ.

Output (OUT or OUT)

The MAX6895/MAX6899 offer an active-high, push-pull

output (OUT), and the MAX6896 offers an active-low

push-pull output (OUT). The MAX6897 offers an active-

high open-drain output (OUT), and the MAX6898 offers

an active-low open-drain output (OUT).

Push-pull output devices are referenced to VCC. Open-

drain outputs can be pulled up to 28V.

Applications Information

Input Threshold

The MAX6895–MAX6899 monitor the voltage on IN

with an external resistive divider (see R1 and R2 in the

Typical Operating Circuit). Connect R1 and R2 as close

to IN as possible. R1 and R2 can have very high values

to minimize current consumption due to low IN leakage

currents (±15nA max). Set R2 to some conveniently high

value (1MΩ, for example) and calculate R1 based on the

desired monitored voltage using the following formula:

MONITOR

R1 R2 1

V−



= ×





where VMONITOR is the desired monitored voltage and

VIN is the detector input threshold (0.5V).

Figure 7. MAX6899P Timing Diagram

VCC

VUVLO

tPROPP tDL tOFF

tDELAY

t > tPW

tPROPP

ENABLE

OUT

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Pullup Resistor Values

(MAX6897/MAX6898)

The exact value of the pullup resistors for the open-drain

outputs is not critical, but some consideration should be

made to ensure the proper logic levels when the device

is sinking current. For example, if VCC = 2.25V and the

pullup voltage is 28V, you would try to keep the sink current

less than 0.5mA as shown in the Electrical Characteristics

table. As a result, the pullup resistor should be greater

than 56kΩ. For a 12V pullup, the resistor should be larger

than 24kΩ. It should be noted that the ability to sink cur-

rent is dependent on the VCC supply voltage.

Typical Application Circuits

Figures 8, 9, 10 show typical applications for the

MAX6895–MAX6899. Figure 8 shows the MAX6895

used with a p-channel MOSFET in an overvoltage pro-

tection circuit. Figure 9 shows the MAX6895 in a low-

voltage sequencing application using an n-channel

MOSFET. Figure 10 shows the MAX6895 used in a mul-

tiple-output sequencing application.

Using an n-Channel Device for Sequencing

In higher power applications, using an n-channel device

reduces the loss across the MOSFETs as it offers a

lower drain-to-source on-resistance. However, an n-

channel MOSFET requires a sufficient VGS voltage to

fully enhance it for a low RDS_ON. The application in

Figure 9 shows the MAX6895 in a switch sequencing

application using an n-channel MOSFET.

Similarly, if a higher voltage is present in the system, the

open-drain version can be used in the same manner.

Figure 9. Low-Voltage Sequencing Using an n-Channel

MOSFET

Figure 8. Overvoltage Protection

MAX6895

ENABLE

GND

VCC

5V BUS

OUT

CDELAY

CCDELAY

1.2V INPUT

1.2V OUTPUT

MONITORED

3.3V

MAX6897

ENABLE

GND

VCC

3.3V ALWAYS ON

OUT

0 TO 28V

RPULLUP

CDELAY

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Figure 10. Multiple-Output Sequencing

CCDELAY CCDELAY

GND GND GND GND

OUT

IN IN IN IN

VCC

ENABLE ENABLE ENABLE ENABLE

DC-DC

3.3V

5V BUS

SYSTEM

ENABLE

2.5V 1.8V 1.2V

DC-DC DC-DC DC-DC

CCDELAY CCDELAY

MAX6895 MAX6895 MAX6895 MAX6895

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Note: All devices are specified over the -40°C to +125°C operating

temperature range.

+Denotes a lead(Pb)-free/RoHS-compliant package.

/V denotes an automotive qualified part; T = Tape and reel.

*Future product—contact factory for availability.

PART ENABLE INPUT OUTPUT INPUT (IN) DELAY ENABLE DELAY

MAX6895AALT+T Active-High Active-High, Push-Pull Capacitor Adjustable Capacitor Adjustable

MAX6895AAZT+T Active-High Active-High, Push-Pull Capacitor Adjustable Capacitor Adjustable

MAX6895PALT+T Active-High Active-High, Push-Pull Capacitor Adjustable 150ns Delay

MAX6895PAZT+T Active-High Active-High, Push-Pull Capacitor Adjustable 150ns Delay

MAX6896AALT+T Active-Low Active-Low, Push-Pull Capacitor Adjustable Capacitor Adjustable

MAX6896AAZT+T Active-Low Active-Low, Push-Pull Capacitor Adjustable Capacitor Adjustable

MAX6896PALT+T Active-Low Active-Low, Push-Pull Capacitor Adjustable 150ns Delay

MAX6896PAZT+T Active-Low Active-Low, Push-Pull Capacitor Adjustable 150ns Delay

MAX6897AALT+T Active-High Active-High, Open-Drain Capacitor Adjustable Capacitor Adjustable

MAX6897AAZT+T Active-High Active-High, Open-Drain Capacitor Adjustable Capacitor Adjustable

MAX6897PALT+T Active-High Active-High, Open-Drain Capacitor Adjustable 150ns Delay

MAX6897PAZT+T Active-High Active-High, Open-Drain Capacitor Adjustable 150ns Delay

MAX6898AALT+T Active-Low Active-Low, Open-Drain Capacitor Adjustable Capacitor Adjustable

MAX6898AAZT+T Active-Low Active-Low, Open-Drain Capacitor Adjustable Capacitor Adjustable

MAX6898PALT+T Active-Low Active-Low, Open-Drain Capacitor Adjustable 150ns Delay

MAX6898PAZT+T Active-Low Active-Low, Open-Drain Capacitor Adjustable 150ns Delay

MAX6899AALT+T Active-Low Active-High, Push-Pull Capacitor Adjustable Capacitor Adjustable

MAX6899AAZT+T Active-Low Active-High, Push-Pull Capacitor Adjustable Capacitor Adjustable

MAX6899PALT+T Active-Low Active-High, Push-Pull Capacitor Adjustable 150ns Delay

MAX6899PAZT+T Active-Low Active-High, Push-Pull Capacitor Adjustable 150ns Delay

PART PIN-PACKAGE TOP MARK

MAX6897AALT+ 6 µDFN +BA

MAX6897AAZT+ 6 Thin SOT23 +AADQ

MAX6897AAZT/V+* 6 Thin SOT23 —

MAX6897AAZT/V+T* 6 Thin SOT23 —

MAX6897PALT+T 6 µDFN +BB

MAX6897PAZT+ 6 Thin SOT23 +AADR

MAX6898AALT+ 6 µDFN +BD

MAX6898AAZT+ 6 Thin SOT23 +AADS

MAX6898AAZT/V+* 6 Thin SOT23 —

MAX6898AAZT/V+T* 6 Thin SOT23 —

MAX6898PALT+T 6 µDFN +BC

MAX6898PAZT+ 6 Thin SOT23 +AADT

MAX6899AALT+ 6 µDFN +LO

MAX6899AAZT+ 6 Thin SOT23 +AADM

MAX6899PALT+T 6 µDFN +LP

MAX6899PAZT+ 6 Thin SOT23 +AADN

MAX6895

ENABLE

GND

VCC

OUT

1.5V TO 5.5V

0.1µF

CDELAY

CCDELAY

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Typical Operating Circuit

Ordering Information (continued)

Selector Guide

PACKAGE

TYPE

PACKAGE

CODE

OUTLINE NO.

LAND

PATTERN NO.

6 µDFN L611+1

21-0147 90-0080

6 Thin SOT23 Z6+1 21-0114 90-0242

1 2 3

6 5 4

OUTVCC CDELAY

ENABLE INGND

MAX6896

MAX6898

µDFN

TOP VIEW

THIN SOT23

TOP VIEW

MAX6895

MAX6897

2GND

ENABLE

3 OUT

CDELAY

VCC

THIN SOT23

TOP VIEW

MAX6896

MAX6898

MAX6899

2GND

ENABLE

3OUT

(OUT)

( ) FOR MAX6899 ONLY.

CDELAY

VCC

www.maximintegrated.com Maxim Integrated

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Package Information

For the latest package outline information and land patterns

(footprints), go to www.maximintegrated.com/packages. Note

that a “+”, “#”, or “-” in the package code indicates RoHS status

only. Package drawings may show a different suffix character, but

the drawing pertains to the package regardless of RoHS status.

Chip Information

PROCESS: BiCMOS

Pin Congurations (continued)

REVISION

NUMBER

REVISION

DATE DESCRIPTION PAGES

CHANGED

5 10/07 — 1, 13, 18

6 11/09 Corrected Absolute Maximum Ratings and made style corrections to Electrical

Characteristics and TOC8 and TOC9 2–5

7 7/10 Revised Figures 3, 4, and 6 7–9

8 7/11 Added automotive packages for MAX6896A and MAX6896P; added top mark to

MAX6896AAZT/V+1 in the Ordering Information table 1

9 12/13 Added automotive packages for MAX6897 in the Ordering Information table 13

10 3/14 Added automotive packages for MAX6898 in the Ordering Information table 13

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses

are implied. Maxim Integrated reserves the right to change the circuitry and specications without notice at any time. The parametric values (min and max limits)

shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.

│

MAX6895–MAX6899 Ultra-Small, Adjustable Sequencing/

Supervisory Circuits

Revision History

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

MAX6896AAZT/V+T MAX6897PAZT+T MAX6896PAZT+T MAX6895AALT+T MAX6895AAZT+T MAX6895PALT+T

MAX6896AALT+T MAX6896AAZT+T MAX6896PALT+T MAX6897AALT+T MAX6897AAZT+T MAX6897PALT+T

MAX6898AALT+T MAX6898AAZT+T MAX6898PALT+T MAX6899AALT+T MAX6899AAZT+T MAX6899PALT+T