Testing Temperature

Luminus core board products are typically measured in such a

way that the characteristics reported agree with how the

devices will actually perform when incorporated into a system.

This measurement is accomplished by mounting the devices on

a 40ºC heat sink and allowing the device to reach thermal

equilibrium while fully powered. Only after the device reaches

equilibrium are the measurements taken. This method of

measurement ensures that Luminus Big Chip LEDs perform in

Every Luminus LED is fully tested to ensure that it meets the high quality standards expected from Luminus’ products.

Photonic Lattice Technology

Luminus’ photonic lattice technology enables large area LED

chips with uniform brightness over the entire LED chip surface.

The optical power and brightness produced by these large

monolithic chips enable solutions which replace arc and

halogen lamps where arrays of traditional high power LEDs

Packaging Technology

Thermal management is critical in high power LED applications.

With a thermal resistance from junction to case of

0.64º C/W. Luminus SST-90 LEDs have the lowest thermal

resistance of any LED on the market. This allows the LED to be

driven at higher current densities while maintaining a low

junction temperature, thereby resulting in brighter solutions

Luminus Big Chip LEDs™ benet from a suite of innovations in the elds of chip technology, packaging and thermal management. These

breakthroughs allow illumination engineers and designers to achieve solutions that are high brightness and high eciency.

SST-90 RGB LEDs are specied for luminous ux and wavelength at a drive current of 3.15 A (0.35 A/mm2) and placed into one of the

following luminous ux (FF) and wavelength (WW) bins:

Note 1: Luminus maintains a +/- 6% tolerance on ux measurements.

Note 2: Only specic bins are available for large order, contact Luminus sales team for more information.

Note 1: WNNX nomenclature corresponds to the following:

The part number SST-90-W65S-F11-N3-G4 refers to a 6500K standard CRI white, SST-90 emitter, with a ux range from 950 to 1,000

lumens and a chromaticity value within the box dened by the four points (0.313, 0.338), (0.321, 0.348), (0.322, 0.336), (0.312, 0.328).

All SST-90 products are packaged and labeled with their respective bin as outlined in the tables and charts from pages 3 to 8. When

shipped, each package will only contain one bin. The part number designation is as follows:

Note 2: Some ux and chromaticity/ wavelength bins may have limited availability. Application specic bin kits, consisting of multiple bins, may be

available. For ordering information, please refer to page 21 and reference the PDS-001692: SST-90 Binning & Labeling document.

Note 1: Recommended mounting screw: M3 or #4

Note 2: All dimensions in millimeters

Note 3: All anode pads on board are interconnected. All cathode pads on board are interconnected

Devices assumes no liability for errors that may appear in this document, and no liability otherwise arising from the application or use of the product or

information contained herein. None of the information provided herein should be considered to be a representation of the tness or suitability of the

product for any particular application or as any other form of warranty. Luminus Devices’ product warranties are limited to only such warranties as

accompany a purchase contract or purchase order for such products. Nothing herein is to be construed as constituting an additional warranty. No

information contained in this publication may be considered as a waiver by Luminus Devices of any intellectual property rights that Luminus Devices

may have in such information. Big Chip LEDs™ is a registered trademark of Luminus Devices, Inc., all rights reserved.

This product is protected by U.S. Patents 6,831,302; 7,074,631; 7,083,993; 7,084,434; 7,098,589; 7,105,861; 7,138,666; 7,166,870; 7,166,871; 7,170,100;

7,196,354; 7,211,831; 7,262,550; 7,274,043; 7,301,271; 7,341,880; 7,344,903; 7,345,416; 7,348,603; 7,388,233; 7,391,059 Patents Pending in the U.S. and

other countries.

Note 1: HH100 - denotes a bin kit comprising of all red ux and wavelength bins as specied on page 5

JG200 - denotes a bin kit comprising of all green ux and wavelength bins as specied on page 5

KF300 - denotes a bin kit comprising of all blue ux and wavelength bins as specied on page 5

Note 2: For ordering information on all available bin kits, please see PDS-001692: SST-90 Binning & Labeling document