PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610
RX
248
Amplifier Built-in Robust
Photoelectric Sensor
SERIES
Marked
Conforming to EMC Directive
(Excluding RX2, RX3 and RX4)
Advanced Sensor
Technology
Automatic Interference Prevention Function
(Retroreflective and Diffuse Reflective Type Sensors Only)
Two sensors can be mounted side by side because of the automatic interference
prevention function. (Excluding the RX2 models)
Test Input
Convenient for operation check before
start-up. (Excluding the RX2 models)
The sensor operation is checked by inter-
rupting the emission repeatedly and confirm-
ing that the output changes accordingly.
Waterproof
The sensor can be hosed down
because of its IP67 construction. The
equipment on which the sensor is
mounted can be washed without any
problem.
Robust
The enclosure is robust as it is made of
die-cast zinc alloy.
OFF
ON
OFF
ON
Test input
Sensing
output Normal Abnormal
Note: However, take care that if it is exposed to
water splashes during operation, it may
detect a water drop itself.
There is no problem
even if the beam of the adjoining sensor is incident.
Amplifier Built-in Type RX
249
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
RX
APPLICATIONS
Detecting person entering
stacker crane path Sensing transparent sheet
Confirming car position at parking garage
RX-M50
RX-PRV500
RX3-M10
Detecting engines Counting cans Sensing machine tools
RX-M10
RX4-M5
RX3... Intelligent Type
Self-diagnosis function for internal
circuit
In addition to the beam intensity
check, the built-in microcomputer
self-diagnoses the internal circuit and
detects a circuit failure, should it
occur.
RX... Standard Type
Wide variety
RX2... DC 2-wire Type
Wiring reduced by 1/3
Wiring can be completed by using
only two, instead of three wires.
Power supply cost: reduced to 1/30 or less
Current consumption: 1mA or less
An additional power supply for the
sensors is not required.
Thru-beam type
Diffuse reflective type
Retroreflective type
Longest range: 50m
Standard (Infrared).........................
Long sensing range (Infrared).......
Visible light (Red)............................
Visible light (Green)..................
10m
50m
2m
500mm
Longest range: 700mm
Long sensing range (Infrared)....
Wide-view (Infrared)...................
Visible light (Red).......................
Sensing object
700mm
300mm
200mm
Longest range: 5m
For specular object sensing
(with polarizing filters, red) ..
For transparent object sensing
(with polarizing filters, red) .....
Long sensing range
(Infrared) .............................. 0.1 to 5m
0.1 to 3m
500mm
Two wires
Additional
power
supply
Wiring is time-consuming
for the 3-wire sensors
and an additional power
supply is required.
PLC
2-wire type
Wiring is simple
with only two wires.
PLC
3-wire type
Receiving
element
Amplifier
circuit
Output
circuit
Oscillation
circuit
Emitting element
Output wire
Receiving
element failure
Emitting LED
failure
Sensing output
wire disconnected
Output transistor
failure
6
14
3
Indication of abnormal conditions
• Operation indicator (red) blinks.
• Self-diagnosis output is ON.
Amplifier
failure
AMP Emitting circuit
failure
5
2
1
5
23
6
6
Micro-
computer
The following parts 1 to 6 are monitored
constantly.
RX4... Heavy Duty Type
Durable against oil
IP67g (JEM) protection has been
achieved by fluorine resin coating on
the enclosure and by using oil resis-
tant protective tube. This sensor can
be used in a harsh environment.
Cover
(Polyethersulphone)
Oil
resistant
protective
tube
Lens:
Polyalylate
Enclosure:
Fluorine
resin coating
Oil resistant
cable
IP67g (JEM)
RX2-PRVM2
Type Appearance Sensing range Model No.
Infrared
Long sensing range
Red
Green
Red (with polarizing filters)
Infrared (long sensing range)
Infrared
Wide-view
Red
Infrared
Red
(with polarizing filters)
Infrared
Infrared
Red (with polarizing filters)
Infrared
Infrared
RX-M10
RX-M50
RX-M2R
RX-500G
RX-PRVM3
RX-PRV500
RX-RVM5
RX-D700
RX-D300
RX-D200R
RX2-M5
RX2-PRVM2
RX2-D300
RX3-M10
RX3-PRVM3
RX3-PRV500
RX3-D700
RX4-M5
RX4-M5-C3
RX4-M5-C5
10m
50m
2m
500mm
0.1 to 3m (Note)
500mm (Note)
0.1 to 5m (Note)
700mm
300mm
200mm
5m
0.1 to 2m (Note)
300mm
10m
0.1 to 3m (Note)
500mm (Note)
700mm
5m
250
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
ORDER GUIDE
For mark
sensing
For transparent
object sensing
For transparent
object sensing
2m cable length
3m cable length
5m cable length
RX (Standard type)
Thru-beam
Retroreflective
Diffuse reflective
Thru-beam
Retroreflective
Diffuse reflective
Thru-beam
Retroreflective
Diffuse reflective
Thru-beam
RX2 (DC 2-wire type)
RX3 (Intelligent type)
RX4 (Heavy
duty type)
Note: The sensing range of the retroreflective type sensor is specified for the RF-230 reflector. Further, the sensing range of RX-PRVM3, RX-RVM5, RX2-PRVM2
and RX3-PRVM3 is the possible setting range for the reflector. The sensor can detect an object less than 0.1m away.
Reflector ReflectorSensor
Setting range
of the reflector
Actual sensing range
of the sensor
Reflector cannot
be placed
in this range 0.1m
3m RX-RVM5: 5m
RX2-PRVM2: 2m
5m cable length type
5m cable length models are available (Standard: 2m). When ordering this type, add suffix ‘-C5’ to the model No. (Excluding RX-4)
(e.g.) 5m cable length type of RX-M10 is ‘RX-M10-C5’.
Description
Sensing range: 2.7m [RX-M10 and RX3-M10]
1.4m [RX2-M5]
Min. sensing object: "8mm
Sensing range: 1.9m [RX-M10 and RX3-M10]
1m [RX2-M5]
Min. sensing object: "6mm
Sensing range: 0.4m [RX-M10 and RX3-M10]
0.2m [RX2-M5]
Min. sensing object: 0.55mm
Sensing range: 3.8m [RX-M10 and RX3-M10]
1.9m [RX2-M5]
Min. sensing object: "8mm
Sensing range: 2.8m [RX-M10 and RX3-M10]
1.4m [RX2-M5]
Min. sensing object: "6mm
Sensing range: 0.8m [RX-M10 and RX3-M10]
0.4m [RX2-M5]
Min. sensing object: 15mm
Sensing range: 7m [RX-M10 and RX3-M10]
3.5m [RX2-M5]
Min. sensing object: "8mm
Sensing range: 4.9m [RX-M10 and RX3-M10]
2.5m [RX2-M5]
Min. sensing object: "6mm
Sensing range: 2.6m [RX-M10 and RX3-M10]
1.3m [RX2-M5]
Min. sensing object: 35mm
Sensing range: 0.2 to 1.5m [RX-RVM5]
0.4 to 1m [RX-PRVM3 and RX3-PRVM3]
Min. sensing object: "30mm
Sensing range: 0.1 to 3.8m [RX-RVM5]
0.1 to 2m [RX-PRVM3 and RX3-PRVM3]
0.1 to 1.3m [RX2-PRVM2]
250mm [RX-PRV500 and RX3-PRV500]
Min. sensing object: "35mm
Protective mounting bracket for RF-210
It protects the reflector from damage and maintains alignment.
For RF-220
For RF-230
This tape can be used in place of the reflector by cutting it to a suitable size.
• Size: 100100mm
• Sensing range: 3m (at 5050mm)
(There may be a slight variation depending on the product.)
Length 500mm
1,000mm
PT-RX1000
CHX-SC2
251
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
OPTIONS
OS-RX-055
(
Slit size 0.55mm
)
OS-RX-505
(
Slit size 50.5mm
)
OS-RX-15
(
Slit size 15mm
)
OS-RX-51
(
Slit size 51mm
)
OS-RX-35
(
Slit size 35mm
)
OS-RX-53
(
Slit size 53mm
)
RF-210
RF-220
MS-RF21-1
MS-RF22
MS-RF23
RF-T110
PT-RX500
Designation Model No. Description
Slit mask
For RX-M10,
RX2-M5 and
RX3-M10 only
Reflector
For retro-
reflective type
sensor only
Reflector
mounting
bracket
Reflective tape
(For RX-RVM5 only)
Protective tube
Sensor checker
(Note)
()
()
Cable is protected from external forces.
It does not rust as it is made of stainless
steel.
It is useful for beam alignment of thru-beam type sensors. The
optimum receiver position is given by indicators, as well as, an
audio signal.
Slit on emitter
Slit on receiver
Slit on both sides
Slit on emitter
Slit on receiver
Slit on both sides
Slit on emitter
Slit on receiver
Slit on both sides
Slit mask
Fitted on the front
face of the sensor
with one-touch.
Slit size
OS-RX-15
~~~~ ~~~
ab
Reflector
RF-210 RF-220
MS-RF22 MS-RF23
12.8mm
33.3mm 11mm
Reflector mounting bracket
MS-RF21-1
Protective tube
Protective tube
Sensor checker
Note: Refer to P.378lfor details of the sensor checker CHX-SC2.
35.3mm 8.3mm
42.3mm
Two M3 (length 12mm) screws
with washers are attached.
Two M3 (length 8mm)
screws with washers
are attached. Two M4 (length 10mm)
screws with washers
are attached.
LEVEL
POWER
CHX-SC2
Sensor checker
Sensing range
Sensing object
Hysteresis
Repeatability
(perpendicular to sensing axis)
Supply voltage
Current consumption
Sensing output
Utilization category
Output operation
Short-circuit protection
Self-diagnosis output
Output operation
Short-circuit protection
Response time
Test input
Operation indicator
Stability indicator
Emitting indicator
Sensitivity adjuster
Automatic interference prevention function
Pollution degree
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
EMC
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Emitting element
Material
Cable
Cable extension
Weight
Accessories
10m 50m 2m 500mm
0.1 to 3m (Note 1)
500mm (Note 1)
0.1 to 5m (Note 1)
700mm (Note 2) 300mm (Note 2) 200mm (Note 2)
"10mm or more opaque object (Note 3)
15% or less of operation distance
0.5mm or less 1mm or less
0.2mm or less
1mm or less
0.5mm or less
12 to 24V DC10% Ripple P-P 10% or less
Emitter: 20mA or less (RX-M50: 25mA or less), Receiver: 25mA or less
40mA or less
NPN open-collector transistor
Maximum sink current: 100mA
Applied voltage: 30V DC or less (between sensing output and 0V)
Residual voltage: 1.5V or less (at 100mA sink current)
0.4V or less (at 16mA sink current)
DC-12 or DC-13
Switchable either Light-ON or Dark-ON
Incorporated
NPN open-collector transistor
Maximum sink current: 50mA
Applied voltage: 30V DC or less (between self-diagnosis output and 0V)
Residual voltage: 1V or less (at 50mA sink current)
0.4V or less (at 16mA sink current)
ON under unstable sensing condition
1ms or less
Incorporated
Red LED (lights up when the sensing output is ON)
Green LED (lights up under stable light received condition or stable dark condition)
Red LED (lights up during beam emission) Continuously variable adjuster
Incorporated (Two units of sensors can be mounted closely.)
3 (Industrial environment)
IP67 (IEC)
25 to60C (No dew condensation or icing allowed), Storage:30 to70C
35 to 85% RH, Storage: 35 to 85% RH
Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face
Emission: EN50081-2, Immunity: EN50082-2
1,000V AC for one min. between all supply terminals connected together and enclosure
20M, or more, with 250V DC megger between all supply terminals connected together and enclosure
10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each
500m/s2acceleration (50G approx.) in X, Y and Z directions for three times each
Red LED (modulated) Infrared LED (modulated)
Enclosure: Die-cast zinc alloy, Indicator cover: Polyethersulphone, Lens: Polycarbonate (retroreflective type: Acrylic)
0.15mm25-core oil, heat and cold resistant cabtyre cable, 2m long
Extension up to total 100m is possible with 0.3mm2, or more, cable (thru-beam type: both emitter and receiver).
Emitter: 70g approx. (RX-M50: 75g approx.) 75g approx.
Receiver: 70g approx. (RX-M50: 75g approx.)
252
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SPECIFICATIONS
Standard type
Environmental resistance
Item Model No.
Type
Thru-beam Retroreflective Diffuse reflective
Infrared
Red (with polarizing filters)
Infrared
Red Green Wide-view Red
RX-M10 RX-M50 RX-M2R RX-500G
RX-PRVM3
RX-PRV500
RX-RVM5 RX-D700 RX-D300
RX-D200R
Long sens-
ing range
For transparent
object sensing
Infrared
Long sensing
range
Notes: 1) The sensing range and the setting object for the retroreflective type sensor are
specified for the RF-230 reflector. Further, the sensing range of RX-PRVM3 and
RX-RVM5 is the possible setting range for the reflector. The sensor can detect an
object less than 0.1m away.
Notes: 2) The sensing range of the diffuse reflective type sensor is specified for white non-
glossy paper (200200mm) as the object.
Notes: 3)
If slit masks (optional) are fitted on RX-M10, an object of 0.55mm can be detected.
Reflector ReflectorSensor
Setting range
of the reflector
0.1m
5m (RX-PRVM3: 3m)
Actual sensing range
of the sensor
Reflector cannot
be placed
in this range
"50mm or
more opaque,
translucent or
specular object
(Note 1)
"50mm or
more opaque,
translucent or
transparent object
(Note 1)
"50mm or
more opaque
or translucent
object
(Note 1)
Opaque, translucent or
transparent object
MS-RX-1 (Sensor mounting bracket): 2 sets
Adjusting screwdriver: 1 No.
MS-RX-1 (Sensor mounting bracket): 1 set
RF-230 (Reflector): 1 No.
Adjusting screwdriver: 1 No.
MS-RX-1 (Sensor mounting bracket): 1 set
Adjusting screwdriver: 1 No.
Infrared LED
(modulated) Red LED
(modulated) Green LED
(modulated) Red LED
(modulated)
Emitter: 0.15mm
2
3-core oil, heat and cold resistant cabtyre cable, 2m long
Receiver: 0.15mm
2
4-core oil, heat and cold resistant cabtyre cable, 2m long
()
5m 0.1 to 2m (Note 1) 300mm (Note 2)
"10mm or more opaque object (Note 3) Opaque, translucent or transparent object
15% or less of operation distance
0.5mm or less 1mm or less 0.5mm or less
12 to 24V DC10% Ripple P-P 10% or less
Emitter: 8mA or less, Receiver: 0.8mA or less (Note 4)
1mA or less (Note 4)
Non contact DC 2-wire type
Load current: 5 to 100mA
Residual voltage: 4V or less (Note 5)
Switchable either Light-ON or Dark-ON
Incorporated
3ms or less
Red LED (lights up when the output is ON)
Green LED Light-ON mode: lights up under stable light received condition
Dark-ON mode: lights up under stable dark condition
Red LED (lights up during beam emission)
Continuously variable adjuster
IP67 (IEC)
20 to60C (No dew condensation or icing allowed), Storage:30 to70C
35 to 85% RH, Storage: 35 to 85% RH
Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face
Power line: 240Vp, 10ms cycle, and 0.5!s pulse width; Radiation: 300Vp, 10ms cycle, and 0.5!s pulse width (with noise simulator)
1,000V AC for one min. between all supply terminals connected together and enclosure
20M, or more, with 250V DC megger between all supply terminals connected together and enclosure
10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each
500m/s2acceleration (50G approx.) in X, Y and Z directions for three times each
Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated)
Enclosure: Die-cast zinc alloy, Indicator cover: Polyethersulphone, Lens: Polycarbonate (RX2-PRVM2: Acrylic)
0.15mm22-core oil, heat and cold resistant cabtyre cable, 2m long
(Note 5)
Emitter: 70g approx., Receiver: 70g approx.
75g approx. 70g approx.
Sensing range
Sensing object
Hysteresis
Repeatability
(perpendicular to sensing axis)
Supply voltage
Current consumption
Sensing output
Output operation
Short-circuit protection
Response time
Operation indicator
Stability indicator
Emitting indicator
Sensitivity adjuster
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
Noise immunity
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Emitting element
Material
Cable
Cable extension
Weight
Accessories
253
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SPECIFICATIONS
DC 2-wire type
Type
Item Model No.
Thru-beam
Retroreflective (with polarizing filters)
Diffuse reflective
RX2-M5 RX2-PRVM2 RX2-D300
MS-RX-1 (Sensor mounting bracket): 2 sets
Adjusting screwdriver: 1 No.
MS-RX-1 (Sensor mounting bracket): 1 set
RF-230 (Reflector): 1 No.
Adjusting screwdriver: 1 No.
MS-RX-1 (Sensor mounting bracket): 1 set
Adjusting screwdriver: 1 No.
Notes: 1) The sensing range and the sensing object for RX2-PRVM2 are specified for the RF-230 reflector. Further, the sensing range is the possible setting range
for the reflector. The sensor can detect an object less than 0.1m away.
Reflector ReflectorSensor
Setting range
of the reflector
0.1m
2m
Actual sensing range
of the sensor
Reflector cannot
be placed
in this range
Notes: 2) The sensing range of RX2-D300 is specified for white non-glossy paper (200200mm) as the object.
Notes: 3) If slit masks (optional) are fitted, an object of 0.55mm can be detected.
Notes: 4) It is the leakage current when the output is in the OFF state.
Notes: 5) When cable is extended, the residual voltage will be increased.
Environmental resistance
()
"50mm or more opaque, translucent or
specular object (Note 1)
10m 0.1 to 3m (Note 1) 500mm (Note 1) 700mm (Note 2)
"10mm or more opaque object (Note 3)
15% or less of operation distance
0.5mm or less 1mm or less 0.2mm or less 0.5mm or less
12 to 24V DC10% Ripple P-P 10% or less
50mA or less
NPN open-collector transistor
Maximum sink current: 100mA
Applied voltage: 30V DC or less (between sensing output and 0V)
Residual voltage: 1.5V or less (at 100mA sink current)
0.4V or less (at 16mA sink current)
Switchable either Light-ON or Dark-ON
Incorporated
NPN open-collector transistor
Maximum sink current: 50mA
Applied voltage: 30V DC or less (between self-diagnosis output and 0V)
Residual voltage: 1V or less (at 50mA sink current)
0.4V or less (at 16mA sink current)
ON under unstable sensing or the sensor circuit failure conditions (Note 4)
3ms or less
Incorporated
Red LED (lights up when the sensing output is ON, blinks when the sensor circuit has failed) (Note 4)
Green LED lights up when the sensing output wire is disconnected, lights up under stable light received condition
or stable dark condition, and blinks under unstable sensing condition (Note 4)
Red LED (lights up during beam emission)
Continuously variable adjuster
Incorporated (Two units of sensors can be mounted closely.)
Self-diagnosis of incident light intensity and internal circuit failure
IP67 (IEC)
25 to60C (No dew condensation or icing allowed), Storage:30 to70C
35 to 85% RH, Storage: 35 to 85% RH
Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face
Power line: 240Vp, 10ms cycle, and 0.5!s pulse width; Radiation: 300Vp, 10ms cycle, and 0.5!s pulse width (with noise simulator)
1,000V AC for one min. between all supply terminals connected together and enclosure
20M, or more, with 250V DC megger between all supply terminals connected together and enclosure
10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each
500m/s2acceleration (50G approx.) in X, Y and Z directions for three times each
Infrared LED (modulated) Red LED (modulated) Infrared LED (modulated)
Enclosure: Die-cast zinc alloy, Indicator cover: Polyethersulphone, Lens: Polycarbonate (retroreflective type: Acrylic)
0.15mm25-core (thru-beam type: 4-core) oil, heat and cold resistant cabtyre cable, 2m long
Extension up to total 100m is possible with 0.3mm2, or more, cable
(thru-beam type: both emitter and receiver).
Emitter: 70g approx., Receiver: 70g approx.
75g approx.
Sensing range
Sensing object
Hysteresis
Repeatability
(perpendicular to sensing axis)
Supply voltage
Current consumption
Sensing output
Output operation
Short-circuit protection
Self-diagnosis output
Output operation
Short-circuit protection
Response time
Test input
Operation indicator
Stability indicator
Emitting indicator
Sensitivity adjuster
Automatic interference prevention function
Self-diagnosis function
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
Noise immunity
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Emitting element
Material
Cable
Cable extension
Weight
Accessories
254
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SPECIFICATIONS
Intelligent type
Environmental resistance
Type
Item Model No.
Thru-beam Retroreflective (with polarizing filters) Diffuse reflective
For transparent object sensing
RX3-M10 RX3-PRVM3 RX3-PRV500 RX3-D700
( )
MS-RX-1 (Sensor mounting bracket):
2 sets
Adjusting screwdriver: 1 No.
MS-RX-1 (Sensor mounting bracket): 1 set
RF-230 (Reflector): 1 No.
Adjusting screwdriver: 1 No.
MS-RX-1 (Sensor mounting bracket):
1 set
Adjusting screwdriver: 1 No.
Notes: 1) The sensing range and the sensing object for the retroreflective type sensor are specified for the RF-230 reflector. Further, the sensing range is the pos-
sible setting range for the reflector. The sensor can detect an object less than 0.1m away.
Reflector ReflectorSensor
Setting range
of the reflector
0.1m
3m
Actual sensing range
of the sensor
Reflector cannot
be placed
in this range
Notes: 2) The sensing range of RX3-D700 is specified for white non-glossy paper (200200mm) as the object.
Notes: 3) If slit masks (optional) are fitted, an object of 0.55mm can be detected.
Notes: 4) Refer to P.261 for details.
Emitter: 20mA or less
Receiver: 45mA or less
"50mm or more opaque, translu-
cent or specular object (Note 1) "50mm or more opaque, translu-
cent or transparent object (Note 1)
Opaque, translucent or
transparent object
5m
"10mm or more opaque object
0.5mm or less
12 to 24V DC10% Ripple P-P 10% or less
Emitter: 20mA or less, Receiver: 25mA or less
NPN open-collector transistor
Maximum sink current: 100mA
Applied voltage: 30V DC or less (between sensing output and 0V)
Residual voltage: 1.5V or less (at 100mA sink current)
0.4V or less (at 16mA sink current)
Switchable either Light-ON or Dark-ON
Incorporated
NPN open-collector transistor
Maximum sink current: 50mA
Applied voltage: 30V DC or less (between self-diagnosis output and 0V)
Residual voltage: 1V or less (at 50mA sink current)
0.4V or less (at 16mA sink current)
ON under unstable sensing condition
1ms or less
Incorporated
Red LED (lights up when the sensing output is ON)
Green LED (lights up under stable light received condition or stable dark condition)
Red LED (lights up during beam emission)
Continuously variable adjuster
IP67 (IEC), IP67g (JEM)
25 to60C (No dew condensation or icing allowed), Storage:30 to70C
35 to 85% RH, Storage: 35 to 85% RH
Sunlight: 11,000?x at the light-receiving face, Incandescent light: 3,500?x at the light-receiving face
Power line: 240Vp, 10ms cycle, and 0.5!s pulse width; Radiation: 300Vp, 10ms cycle, and 0.5!s pulse width (with noise simulator)
1,000V AC for one min. between all supply terminals connected together and enclosure
20M, or more, with 250V DC megger between all supply terminals connected together and enclosure
10 to 500Hz frequency, 1.5mm amplitude (10G max.) in X, Y and Z directions for two hours each
500m/s2acceleration (50G approx.) in X, Y and Z directions for three times each
Infrared LED (modulated)
Enclosure: Die-cast zinc alloy (Fluorine resin coating), Indicator cover: Polyethersulphone, Lens: Polyalylate, Protective tube sheath: Oil resistant PVC
0.15mm24-core (emitter: 3-core) oil, heat and cold resistant cabtyre cable
1m 2m 4m
Extension up to total 100m is possible for both emitter and receiver with 0.3mm2, or more, cable.
Emitter: 175g approx., Receiver: 175g approx. Emitter: 265g approx., Receiver: 265g approx. Emitter: 495g approx., Receiver: 495g approx.
MS-RX-2 (Sensor mounting bracket): 2 sets, Adjusting screwdriver: 1 No.
Sensing range
Sensing object
Repeatability
(perpendicular to sensing axis)
Supply voltage
Current consumption
Sensing output
Output operation
Short-circuit protection
Self-diagnosis output
Output operation
Short-circuit protection
Response time
Test input
Operation indicator
Stability indicator
Emitting indicator
Sensitivity adjuster
Protection
Ambient temperature
Ambient humidity
Ambient illuminance
Noise immunity
Voltage withstandability
Insulation resistance
Vibration resistance
Shock resistance
Emitting element
Material
Cable
Protective tube length
Cable extension
Weight
Accessories
255
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SPECIFICATIONS
Heavy duty type
Type
Item Model No.
Thru-beam
Cable length 2m Cable length 3m Cable length 5m
RX4-M5 RX4-M5-C3 RX4-M5-C5
Environmental resistance
256
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
I/O CIRCUIT AND WIRING DIAGRAMS
RX-RX3-
RX4-
I/O circuit diagram
RX2-
I/O circuit diagram Wiring diagrams
Wiring diagram
Users’ circuitInternal circuit
Sensor circuit
D
ZD1
Tr1
(Brown) V
(Black)
Sensing output (Note 2)
(Orange)
Self-diagnosis output (Note 3)
Color code
100mA max.
ZD2
Tr2(Blue) 0V
Load
Load
50mA max.
1mA max.
(Pink) Test input
12 to 24V DC
10%
m1
(Note 1)
Notes: 1) The receiver of the thru-beam type sensor does not incorporate the
test input.
Notes: 2) The emitter of the thru-beam type sensor does not incorporate the
sensing output.
Notes: 3) The emitter of the thru-beam type sensors RX and RX4 does not
incorporate the self-diagnosis output.
Brown
Black
Blue
Load
Load
m1
Orange
Pink
12 to 24V DC
10%
Symbols ...
D:
Reverse supply polarity protection diode
ZD1, ZD2: Surge absorption zener diode
Tr1, Tr2: NPN output transistor
Symbols ...
D:
Reverse supply polarity protection diode
ZD: Surge absorption zener diode
Tr: PNP output transistor
or
Non-voltage contact or NPN open-collector transistor
[Supply voltage 2.5V] or more (4.5V or more for the RX3 model): emission
[Supply voltage 3.3V] or less (2.5V or less for the RX3 model): emission stopped
m1
Emitter of thru-beam type sensor
Receiver of thru-beam type sensor, retroreflective
and diffuse reflective type sensors Receiver of thru-beam type sensor, retroreflective
and diffuse reflective type sensors
Emitter of thru-beam type sensor
Users’ circuitInternal circuit
D(Brown) V
(Blue) 0V
Color code
12 to 24V DC
10%
Sensor circuit
Brown
Blue
12 to 24V DC
10%
Bleeder resistance
5 to 100mA in the ON state
1mA in the OFF state
4V in the
ON state
Tr
ZD
Users’ circuitInternal circuit
(Brown) Output
(Blue) 0V
Color code
Load
Receiver of thru-beam
type sensor: 0.8mA
()
12 to 24V DC
10%
Sensor circuit
Brown
Blue
Load
12 to 24V DC
10%
1) The load should not be actuated by the leakage current (1mA; 0.8mA for
receiver of thru-beam type sensor) in the OFF state.
2) The load should be actuated by (supply voltage 4V) in the ON state.
3) The current in the ON state should be between 5 to 100mA DC.
In case the current is less than 5mA, connect a bleeder resistance in
parallel to the load (shown in dotted line above) so that a current of
3mA, or more, flows.
Conditions for the load
257
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SENSING CHARACTERISTICS (TYPICAL)
RX-All models
Correlation between setting distance and excess gain
0 20 60 80 100
1
10
5
100
40
Excess gain
50
RX-M50
RX-M10
Setting distance L (m)
02 6810
1
10
5
100
4
Excess gain
50
RX-RVM5
RX-PRVM3
RX-M2R
Setting distance L (m)
0 200 600 800 1,000
1
10
5
100
400
Excess gain
50
RX-D700
RX-PRV500
RX-500G
RX-D300
RX-D200R
Setting distance L (mm)
RX-M103
RX3-M10 Thru-beam type
Parallel deviation
RX-M50 Thru-beam type
Parallel deviation Angular deviation
RX-M2R Thru-beam type
Parallel deviation Angular deviation
Parallel deviation with slit masks
(0.55mm) Parallel deviation with slit masks
(15mm) Parallel deviation with slit masks
(35mm)
Angular deviation
400 200 0 200 400
0
10
5
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
#
10 5 0 5 10
0
10
5
L
Operating angle $( ° )
Emitter
Receiver
$
Receiver
angular
deviation Emitter
angular
deviation
Setting distance L (m)
Center RightLeft
200 100 0 100 200
0
1
2
4
3
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
Slit on
both sides
Slit on
emitter
Slit on
receiver
#
200 100 0 100 200
0
1
2
4
3
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
#
Slit on
both sides
Slit on
emitter
Slit on
receiver
400 200 0 200 400
0
2
4
8
6
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
Slit on
both side
Slit on
receiver
#
Slit on
emitter
1,000 500 0 500 1,000
0
20
40
80
60
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
#
10 5 0 5 10
0
20
40
80
60
L
Emitter
Receiver
$
Emitter
angular
deviation
Receiver
angular
deviation
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
200 100 0 100 200
0
2
1
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
#
40 20 0 20 40
0
2
1
L
Emitter
Receiver
$
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
258
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SENSING CHARACTERISTICS (TYPICAL)
RX-500G Thru-beam type
Parallel deviation Angular deviation
RX4-M5Thru-beam type
Parallel deviation Angular deviation
40 20 0 20 40
0
200
400
800
600
L
Emitter
Receiver
Center RightLeft
Operating point ? (mm)
#
Setting distance L (mm)
10 5 0 5 10
0
200
400
800
600
L
Emitter
Receiver
$
Setting distance L (mm)
Operating angle $( ° )
Center RightLeft
400 200 0 200 400
0
2
4
8
6
L
Emitter
Receiver
#
Setting distance L (m)
CenterLeft Right
Operating point ?(mm)
10 5 0 5 10
0
2
4
8
6L
Emitter
Receiver
Receiver
angular
deviation
Emitter
angular
deviation
$
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
RX-PRVM33
RX3-PRVM3 Retroreflective type
Parallel deviation Angular deviation
RX-PRV5003
RX3-PRV500 Retroreflective type
Parallel deviation Angular deviation
100 50 0 50 100
0
1
2
4
3
L
Sensor
Reflector
(RF-230)
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
#
40 20 0 20 40
0
1
2
4
3
Reflector
angular
deviation
Sensor
angular
deviation
L
Sensor
Reflector angular deviation
L
Sensor angular deviation
Reflector (RF-230)
Sensor
$
$
Reflector (RF-230)
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
100 50 0 50 100
0
200
400
800
600
L
Sensor
Reflector
(RF-230)
Setting distance L (mm)
Center RightLeft
Operating point # (mm)
#
40 20 0 20 40
0
200
400
800
600
L
L
Reflector
angular
deviation
Sensor
angular
deviation
Reflector angular deviation
Reflector (RF-230)
Sensor
angular
deviation
Reflector
(RF-230)
Sensor
Sensor
$
Operating angle $( ° )
Center RightLeft
Setting distance L (mm)
$
RX2-M5 Thru-beam type
Parallel deviation
Parallel deviation with slit masks
(0.55mm) Parallel deviation with slit masks
(15mm) Parallel deviation with slit masks
(35mm)
Angular deviation
400 200 0 200 400
0
2
4
8
6
L
Emitter
Receiver
Setting distance L (m)
Center RightLeft
Operating point ? (mm)
#
10 5 0 5 10
0
2
4
8
6L
Emitter
Receiver
$
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
Receiver
angular
deviation
Emitter
angular
deviation
100 50 0 50 100
0
0.5
1
2
1.5
L
Emitter
Receiver
Slit on
both sides
Slit on
emitter
Slit on
receiver
Center RightLeft
Operating point ? (mm)
#
Setting distance L (m)
100 50 0 50 100
0
0.5
1
2
1.5
L
Emitter
Receiver
Center RightLeft
Operating point ? (mm)
#
Slit on
both sides
Slit on
emitter
Slit on
receiver
Setting distance L (m)
200 100 0 100 200
0
1
2
4
3
L
Slit on
both sides
Slit on
emitter
Slit on
receiver
Emitter
Receiver
Center RightLeft
Operating point ? (mm)
#
Setting distance L (m)
259
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SENSING CHARACTERISTICS (TYPICAL)
RX-RVM5 Retroreflective type
Parallel deviation Angular deviation
RX2-PRVM2 Retroreflective type
Parallel deviation Angular deviation
100 50 0 50 100
0
2
4
8
6
L
Sensor
Reflector
(RF-230)
Setting distance L (m)
Center RightLeft
Operating point # (mm)
#
40 20 0 20 40
0
2
4
8
6
L
L
Reflector
angular
deviation
Sensor
angular
deviation
Reflector angular deviation
Reflector (RF-230)
Sensor angular
deviation
Reflector
(RF-230)
Sensor
Sensor
$
$
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
100 50 0 50 100
0
2
1
L
Sensor
Reflector
(RF-230)
Setting distance L (m)
Center RightLeft
Operating point # (mm)
#
40 20 0 20 40
0
2
1
L
L
Reflector
angular
deviation
Sensor
angular
deviation
Sensor angular
deviation
Reflector
(RF-230)
Sensor
Sensor
$
$
Reflector angular
deviation
Reflector (RF-230)
Operating angle $( ° )
Setting distance L (m)
Center RightLeft
RX-D7003
RX3-D700 Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
20 10 0 10 20
0
200
400
800
600
L
Sensor
200200mm
White non-
glossy paper
Setting distance L (mm)
Center RightLeft
Operating point # (mm)
#
050 100 150 200
200
400
800
600
L
Sensor
aamm
White non-
glossy paper
Sensing range L (mm)
White non-glossy paper
side length a (mm)
RX-D300 Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
20 10 0 10 20
0
100
200
400
300
L
Sensor
200200mm
White non-glossy paper
Setting distance L (mm)
Center RightLeft
Operating point # (mm)
#
50 100 150 200
0
100
200
400
300
L
Sensor
aamm
White non-
glossy paper
White non-glossy paper
side length a (mm)
Sensing range L (mm)
RX-D200R Diffuse reflective type
Sensing field Correlation between sensing object size and sensing range
20 10 0 10 20
0
200
100
L
Sensor
200200mm
White non-
glossy paper
Setting distance L (mm)
Center RightLeft
Operating point # (mm)
#
050 100 150 200
200
100
L
Sensor
aamm
White non-
glossy paper
Sensing range L (mm)
White non-glossy paper
side length a (mm)
As the sensing object size becomes smaller
than the standard size (white non-glossy paper
200200mm), the sensing range shortens, as
shown in the left graph.
For plotting the left graph, the sensitivity has
been set such that a 200200mm white
non-glossy paper is just detectable at a dis-
tance of 300mm.
()
As the sensing object size becomes smaller
than the standard size (white non-glossy paper
200200mm), the sensing range shortens, as
shown in the left graph.
For plotting the left graph, the sensitivity has
been set such that a 200200mm white
non-glossy paper is just detectable at a dis-
tance of 200mm.
()
As the sensing object size becomes smaller
than the standard size (white non-glossy paper
200200mm), the sensing range shortens, as
shown in the left graph.
For plotting the left graph, the sensitivity has
been set such that a 200200mm white
non-glossy paper is just detectable at a dis-
tance of 700mm.
()
260
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
SENSING CHARACTERISTICS (TYPICAL)
RX2-D300 Diffuse reflective type
PRECAUTIONS FOR PROPER USE Refer to P.820lfor general precautions.
All models RX-RVM5
RX-PRVM3 RX-PRV500
RX2-PRVM2
Sensing field Correlation between sensing object size and sensing range
20 10 0 10 20
0
100
200
400
300
L
Sensor
200200mm
White non-
glossy paper
Setting distance L (mm)
Center RightLeft
Operating point # (mm)
#
0 50 100 150 200
100
200
400
L
Sensor
300
aamm
White non-
glossy paper
White non-glossy paper
side length a (mm)
Sensing range L (mm)
This product is not a safety sensor. Its use is not
intended or designed to protect life and prevent body
injury or property damage from dangerous parts of
machinery. It is a normal object detection sensor.
Mounting
The tightening torque should be 1.17N m or less.
Wiring
The self-diagnosis output is not incorporated with a short-
circuit protection circuit. Do not connect it directly to a
power supply or a capacitive load.
Others
Do not use during the initial transient time (50ms) after the
power supply is switched on.
M4 (length 16mm)
hexagon-socket-head bolt
Attached mounting bracket
Glossy object sensing
Please take care of the following points when detecting
materials having a gloss.
1Make L, shown in the diagram, sufficiently long.
2Install at an angle of 10 to 30 degrees to the sensing
object.
Retroreflective type sensor with polarizing filters
If a shiny object is covered or wrapped with a transparent
film such as those described below, the retroreflective type
sensor with polarizing filters may not be able to detect it.
In that case, follow the steps given below.
Can wrapped by clear film
Aluminum sheet covered by plastic film
Gold or silver color (glossy) label or wrapping paper
Tilt the sensor with respect to the sensing object while fitting.
Reduce the sensitivity.
Increase the distance between the sensor and the sensing
object.
LMake L sufficiently long
Sensor
10 to 30
Glossy surface
Sensing object
Reflector
Example of sensing objects
Steps
As the seinsing object size becomes smaller
than the standard size (white non-glossy paper
200200mm), the sensing range shortens, as
shown in the left graph.
For plotting the left graph, the sensitivity has
been set such that a 200200mm white
non-glossy paper is just detectable at a dis-
tance of 300mm.
()
261
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
PRECAUTIONS FOR PROPER USE Refer to P.820lfor general precautions.
RX2-RX3-
Self-diagnosis output
The self-diagnosis output turns ON when the incident light
intensity is reduced due to the lens being soiled with dust
or dirt, due to beam misalignment, or if the internal circuit
has failed. If the self-diagnosis output and the
operation indicator behave as given in the table below,
abnormality is indicated and should be rectified.
Wiring
Always connect the sensor to the power supply through a
load. If the sensor is connected to the power supply direct-
ly, the short-circuit protection makes the sensor inoperable
(The output stays in the OFF state and no indicator lights
up). If this happens, connect the sensor to the power sup-
ply through a load.
Further, note that the sensor will be damaged if the power
supply is connected in reverse without a load.
Do not connect sensors in series (AND circuit).
The residual voltage of the sensor is 4V. Before connect-
ing to a relay, be aware of the actuation voltage of the
relay.
(Not all 12V relays may be connected as the load.)
DC
power
supply
Brown lead wire
Blue lead wire
DC
power
supply
Brown lead wire
Blue lead wire
DC power supply
Load
12V DC
VR (Relay actuation voltage)
VS4V Residual voltage
Relay actuation
voltage:
VRh124V
h8V
()
when the sensing
output is ON.
Relay
Symptoms
Failure Remedy
Self-
diagnosis
output
Operation
indicator
(Red LED)
Stability
indicator
(Green LED)
ON
Blinking
pattern 1
(Note 1)
Lights off
Blinking
pattern 2
(Note 1)
Lights up
Lights up/
Lights off
Lights up/
Lights off
Blinking
pattern 2
(Note 1)
Sensing output wire is
disconnected during
unstable light received
condition or unstable
dark condition.
Check the sensing
output wire (black lead
wire) and the place-
ment of the sensor.
Unstable sensing con-
dition due to soiled lens
or beam misalignment.
(Note 2)
Check the placement
of the sensors and the
surface condition of
the lenses.
Sensing output is short-
circuited and excessive
current flows.
Check the sensing
output wire (black lead
wire) and the load.
Sensing output wire is
disconnected. Check the sensing
output wire (black lead
wire).
Failure of the sensor
circuit.
Failure of the emitting
or receiving elements,
emitting circuit, ampli-
fier circuit, or output
transistor.
If the sensor does not
operate after the pow-
er is supplied once
again, please contact
our office.
Notes:
1) There are two blinking patterns of the operation indicator and the
stability indicator.
2) The time chart for unstable light received condition and unstable dark con-
dition are shown in the following diagram.
Blinking
pattern 1
ON
OFF
0.1 sec. 0.4 sec. 0.1 sec.
Repeat
Stable light received level
Sensing output
threshold level
Stable dark level
Sensing
condition
Sensing output
operation
indicator
in the Light-
ON mode
Stability indicator
Self-diagnosis
output
ON (Lights up)
OFF (Lights off)
Lights up
Lights off
OFF
3ON
21
1
Insufficient beam intensity Insufficient beam interruption
(Blink 2)(Blink 2)
()
()
1The self-diagnosis output transistor stays in the ‘OFF’ state during stable
sensing.
2When the sensing output changes, if the incident light intensity does not
reach the stable light received level or the stable dark level, the self-
diagnosis output becomes ON.
Further, the self-diagnosis output changes state when the sensing output
changes from Light to Dark state. (It is not affected by the operation mode
switch.)
3In case of insufficient beam interruption, there will be a time lag before the
self-diagnosis output turns ON.
3) For the emitter of the thru-beam type diagnosis is only for the emitting ele-
ment and circuit failure, and the failure is indicated by blinking pattern 1.
4) The self-diagnosis output (for sensing output wire disconnection, output
transistor failure) may not be generated or changed depending on the fault
conditions.
5) When the test input is connected to 0V, the self-diagnosis is inoperable.
6) Turning the sensitivity adjuster to the minimum simulates the internal cir-
cuit failure condition. Set it at the proper position.
()
0.1 sec. 0.1 sec. 0.1 sec. 0.3 sec. 0.1 sec.
0.1 sec.
Repeat
0.1 sec.
ON
OFF
Blinking
pattern 2
262
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
PRECAUTIONS FOR PROPER USE Refer to P.820lfor general precautions.
RX4-RX-4
RX4-
DIMENSIONS (Unit: mm)
RX-M10 RX-M2R RX-500G
RX2-M5 RX3-M10
Sensor Sensor
RX-M50
Self-diagnosis function
The sensor diagnoses the incident light intensity, and if it is
reduced due to dirt or dust, or beam misalignment an out-
put is generated.
Connection of protective tube connector
Connect the junction connector securely as shown below.
The tightening torque should be 0.98N m or less.
When mounted on a plate
When mounted with a female screw
When connected to another protective tube
Oil resistant protective tube
Junction connector
"14.5 hole
Oil resistant cable
M14 nut (Accessory)
7mm or less
Oil resistant protective tube
Junction connector
Effective thread length
11mm or more
M141 tapped hole
Oil resistant protective tube
Junction connector
Can be connected to a straight combination
connector (RCC-F1060-M14) manufactured
by NIPPON FLEX
Stable light received level
Sensing output
threshold level
Stable dark level
Sensing condition
Stability indicator
Self-diagnosis output
ON (Lights up)
OFF (Lights off)
Lights up
Lights off
OFF
ON
Insufficient
beam intensity Insufficient
beam interruption
Sensing output
(operation indicator )
(in the Light-ON mode)
1
123
1The self-diagnosis output transistor stays in the ‘OFF’ state during
stable sensing.
2When the sensing output changes, if the incident light intensity does not
reach the stable light received level or the stable dark level, the self-
diagnosis output becomes ON.
Further, the self-diagnosis output changes state when the sensing output
changes from Light to Dark state. (It is not affected by the operation mode
switch.)
3In case of insufficient beam interruption, there will be a time lag before the
self-diagnosis output turns ON.
20
14
Beam axis
Stability indicator
(Green) (Note 2)
Cover-fixing screw
Sensitivity adjuster (Note 1)
Operation mode switch (Note 1)
Indicator cover Operation indicator
(Red) (Note 1)
(2.5)
35
35 32-M40.7 thru-hole
threads
14
14
3.6
"3.7 cable 2m long
M80.75
20
14
Beam axis
Stability indicator
(Green) (Note 2)
Cover-fixing screw
Sensitivity adjuster (Note 1)
Operation mode switch (Note 1)
Indicator cover Operation indicator
(Red) (Note 1)
(2.5)
35
43 32-M40.7 thru-hole
threads
14
14
3.6
"3.7 cable 2m long
M80.75
Notes: 1) Not incorporated on the emitter.
Notes: 2) It is the emitting indicator (red) on the emitter of the thru-beam type
sensor.
Notes: 1) Not incorporated on the emitter.
Notes: 2) It is the emitting indicator (red) on the emitter of the thru-beam type
sensor.
263
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
DIMENSIONS (Unit: mm)
RX4-M5Sensor
RX-PRVM3 RX-PRV500 RX-RVM5
RX2-PRVM2 RX3-PRVM3 RX3-PRV500
Sensor
"
Sensitivity adjuster (Note 1) Stability indicator (Green) (Note 2)
Cover-fixing screw
Stability indicator (Red) (Note 1)
Operation mode switch (Note 1)
Indicator cover
Beam
axis
14 (2.5)
35
35
3
20
2-M40.7 thru-hole threads
"9 oil resistant protective tube
2m long (Note 3)
(Oil resistant PVC) "3.7 cable
14
14 14 15
20.9
M141
Waterproof packing
10
(NBR)
(Brass)
Junction connector
(Brass Black chromate)
Connector on the sensor
(16.5)
15.5
14
Stability indicator
(Green)
Cover-fixing screw
Sensitivity adjuster
Operation mode indicator
Indicator cover Operation indicator
(Red)
(2.5)
35
39 3
2-M40.7 thru-hole threads
14
14
3.6
"3.7 cable 2m long
M80.75
Center of sensing
RX-D700 RX-D300 RX-D200R
RX2-D300 RX3-D700
Sensor
Reflector (Accesory for the retroreflective type sensor)
RF-230
15.5
14
Center of
sensing
Stability indicator (Green)
Cover-fixing screw
Sensitivity adjuster
Operation mode switch
Indicator cover Operation indicator (Red)
(2.5)
35
35 32-M40.7 thru-hole threads
14
14
3.6
"3.7 cable 2m long
M80.75
50.3
49.3
59.3
(30)
40
5
8.3
3.3
10
2-"4.6
mounting
holes
RF-220 Reflector (Optional) Reflector (Optional)
RF-210
35.3
42.334.3
8
25
4
8.3
3.3
2-"3.6
mounting
holes
(21)
10
25
3.2
33.3
12.8
11
Reflector
Base
M3 nut mounting holes
(for mounting at the back)
2-"3.4 thru-holes
(for mounting at the side)
(for mounting at the back)
2-"3.4 holes 6 deep
(for mounting at the side)
2-M3 nut mounting holes
Notes: 1) Not incorporated on the emitter.
Notes: 2) It is the emitting indicator (red) on the emitter of the thru-beam type
sensor.
Notes: 3) The given length of the protective tube is for RX4-M5-C3.
Notes: 3) (RX4-M5: 1m, RX4-M5-C5: 4m)
Material: Acrylic (Reflector)
Material: ABS (Base)
Material: Acrylic (Reflector)
Material: ABS (Base) Material: Acrylic (Reflector)
Material: ABS (Base)
Two M3 (length 8mm)
screws with washers and
two nuts are attached.
264
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
DIMENSIONS (Unit: mm)
MS-RX-1 Sensor mounting bracket (Accessory for RX-, RX2-, RX3-)
8.5
16 8
10
10
4.4
4.4
37
13.5 13.5
515
2
3
R14
54.4
15
24
38
45
t2
14
8.5 10
4.4
4.4
45
37
25.5
17
8
35
(2.5)
6
16
30
23
Assembly dimensions
Mounting drawing with RX-D700
MS-RX-2 Sensor mounting bracket (Accessory for RX4-)
37
4.4
4.4
8.5
16 8
5
3
25
4.4
36
50
57
t2
15
15
R14
13.5 13.5
10
10
35
4.4
10
4.4 8.5
816
37
10
35
14
17
30
57
(2.5)
42
t2
Beam axis
Assembly dimensions
Mounting drawing with RX4-M5
MS-RF21-1 Reflector mounting bracket for RF-210 (Optional)
Assembly dimensions
Material: Cold rolled carbon steel (SPCC)
Two M4 (length 16mm) hexagon-socket-head
bolts are attached.
Material: Cold rolled carbon steel (SPCC)
Two M4 (length 16mm) hexagon-socket-head
bolts are attached.
Material: Stainless steel (SUS304)
Two M3 (length 12mm) screws
with washers are attached.
23
50
5.5
16
10
3.5
3.2
12.5
R7.5
25
46
t1.2
13
"36
"25
20
30
23
50
5.5
10
12.8
13
46
25
"36
20
30
265
RX
PHOTOELECTRIC SENSORS
EQ-20
EQ-30
EX-40
RX-LS200
CY
EX
PX-2
RT-610 Amplifier Built-in Type RX
DIMENSIONS (Unit: mm)
MS-RF22 Reflector mounting bracket for RF-220 (Optional)
25
4.5
10
11
25
35
4
16
10
6
8
44
20
t1.6
8-M30.5 thru-hole threads
4.5 25
10 28.3
19.3
8.3
35.3
44.3
6
34.3
8
4
t1.6
(27) (21)
Assembly dimensions
MS-RF23 Reflector mounting bracket for RF-230 (Optional)
40 4.5 10
11
50
40 5
16
15
18
7
26
12
35 61
20
t2
(3) (28)
(3)
8-M40.7 thru-hole threads
40
4.5
28.3
19.3
8.3
50.3
61.3
7
49.3
5
40
t 2
10
10
(30)
(37)
Assembly dimensions
PT-RX5000
PT-RX1000 Protective tube (Optional)
Material: Cold rolled carbon steel (SPCC)
Material: (Uni-chrome plated)
Two M3 (Length 8mm) screws with washers are attached.
Material: Cold rolled carbon steel (SPCC)
Material: (Uni-chrome plated)
Two M4 (Length 10mm) screws with washers are attached.
Model No. L (mm)
PT-RX500 1,500
PT-RX1000 1,000
L
6.5 15
"18
"5
14
M101 thread
"10 [Brass (C3604) (Nickel plated)]
[Stainless steel (SUS304)]
Internal thread
M80.75, 4 deep
(Brass) "7 spiral tube
Length L
10
0
10
0