E M C C o m p o n e n t s July 2013 Chip Beads For signal line HFxxACB series HFxxACB2012 HFxxACB3216 HFxxACB3225 HFxxACB4532 [0805 inch]* [1206 inch] [1210 inch] [1812 inch] * Dimensions Code JIS[EIA] (2/17) E M C C o m p o n e n t s REMINDERS FOR USING THESE PRODUCTS Before using these products, be sure to request the delivery specifications. SAFETY REMINDERS Please pay sufficient attention to the warnings for safe designing when using these products. REMINDERS The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40C, Humidity: 10 to 75% RH or less). If the storage period elapses, the soldering of the terminal electrodes may deteriorate. Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). Before soldering, be sure to preheat components. The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150C. Soldering corrections after mounting should be within the range of the conditions determined in the specifications. If overheated, a short circuit, performance deterioration, or lifespan shortening may occur. When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal design. Carefully lay out the coil for the circuit board design of the non-magnetic shield type. A malfunction may occur due to magnetic interference. Use a wrist band to discharge static electricity in your body through the grounding wire. Do not expose the products to magnets or magnetic fields. Do not use for a purpose outside of the contents regulated in the delivery specifications. The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions set forth in the each catalog, please contact us. (1) Aerospace/Aviation equipment (2) Transportation equipment (cars, electric trains, ships, etc.) (3) Medical equipment (4) Power-generation control equipment (5) Atomic energy-related equipment (6) Seabed equipment (7) Transportation control equipment (8) Public information-processing equipment (9) Military equipment (10) Electric heating apparatus, burning equipment (11) Disaster prevention/crime prevention equipment (12) Safety equipment (13) Other applications that are not considered general-purpose applications When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing protection circuit/device or providing backup circuits in your equipment. 001-01 / 20130722 / e9415_hf_acb.fm (3/17) E M C C o m p o n e n t s Chip Beads Product compatible with RoHS directive Halogen-free Compatible with lead-free solders For signal line Overview of the HFxxACB Series FEATURES Noise reduction solution for general signal lines. Lineup includes 4 sizes from 201209 to 453215. Achieves various frequency characteristics by using 3 materials with different features. There is no directivity. APPLICATION Signal line noise removal for DSCs, DVCs, PCs, TVs, printers, game machines, smart grids, wireless base stations, industrial equipment, automobiles, etc. PART NUMBER CONSTRUCTION HF70 ACB Material name Series name HF70 HF50 HF30 201209 - LxWxT Dimensions (mm) 201209 2.0x1.25x0.9 321611 3.2x1.6x1.1 322513 3.2x2.5x1.3 453215 4.5x3.2x1.5 T Packaging style T Taping OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT Temperature range Operating Storage Type temperature temperature C C HFxxACB2012 -40 to +125 -40 to +125 HFxxACB3216 -40 to +125 -40 to +125 HFxxACB3225 -40 to +125 -40 to +125 HFxxACB4532 -40 to +125 -40 to +125 Operating temperature range includes self-temperature rise. The Storage temperature range is for after the circuit board is mounted. Package quantity Individual weight pieces/reel 2,000 2,000 2,000 1,000 mg 10 22 46 94 RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://www.tdk.co.jp/rohs/ Halogen-free: Indicates that Cl content is less than 900ppm, Br content is less than 900ppm, and that the total Cl and Br content is less than 1500ppm. * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (4/17) E M C C o m p o n e n t s Overview of the HFxxACB Series RECOMMENDED REFLOW PROFILE Preheating Soldering Natural cooling Peak T: Temperature T4 T3 T2 T3 t3 T1 t1 t2 t: Time Preheating Temp. T1 T2 150C 180C Time t1 60 to 120s Soldering Temp. Time T3 t2 230C 30 to 60s Peak Temp. T4 250 to 260C Time t3 10s * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (5/17) E M C C o m p o n e n t s HFxxACB series HFxxACB2012 Type SHAPE & DIMENSIONS 2.000.20 0.900.20 Terminal electrode 1.250.20 Ferrite 0.300.20 0.300.20 Insulation resin Dimensions in mm 1.0 RECOMMENDED LAND PATTERN 1.0 1.0 1.0 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (6/17) E M C C o m p o n e n t s HFxxACB series HFxxACB2012 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 10 11 7 Tolerance 25% 25% 25% DC resistance (: )max. Rated current (mA)max. Part No. 0.1 0.1 0.1 600 600 600 HF70ACB201209-T HF50ACB201209-T HF30ACB201209-T * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (7/17) E M C C o m p o n e n t s HFxxACB series HFxxACB2012 Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS HF70ACB201209 HF50ACB201209 1000 100 Z 10 1000 100 Z 10 X X R 10 100 1000 Z, X, R () Z, X, R () Z, X, R () 1000 1 1 HF30ACB201209 1 1 Frequency (MHz) R 10 100 Frequency (MHz) 1000 100 Z 10 1 1 X 10 100 R 1000 Frequency (MHz) * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (8/17) E M C C o m p o n e n t s HFxxACB series HFxxACB3216 Type SHAPE & DIMENSIONS 3.200.20 1.100.20 Terminal electrode 1.600.20 Ferrite 0.300.20 0.300.20 Insulation resin Dimensions in mm 1.4 RECOMMENDED LAND PATTERN 1.1 2.2 1.1 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (9/17) E M C C o m p o n e n t s HFxxACB series HFxxACB3216 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 26 31 19 Tolerance 25% 25% 25% DC resistance (: )max. Rated current (mA)max. Part No. 0.2 0.2 0.2 500 500 500 HF70ACB321611-T HF50ACB321611-T HF30ACB321611-T * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (10/17) E M C C o m p o n e n t s HFxxACB series HFxxACB3216 Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS HF70ACB321611 HF50ACB321611 1000 100 Z 10 100 Z 10 X 100 Z X 10 X R 1 1 1000 Z, X, R () Z, X, R () Z, X, R () 1000 HF30ACB321611 R R 10 100 1000 1 1 Frequency (MHz) 10 100 Frequency (MHz) 1000 1 1 10 100 1000 Frequency (MHz) * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (11/17) E M C C o m p o n e n t s HFxxACB series HFxxACB3225 Type SHAPE & DIMENSIONS 3.200.20 1.300.20 Terminal electrode 2.500.20 Ferrite 0.300.20 0.300.20 Insulation resin Dimensions in mm 2.3 RECOMMENDED LAND PATTERN 1.1 2.2 1.1 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (12/17) E M C C o m p o n e n t s HFxxACB series HFxxACB3225 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 52 60 31 Tolerance 25% 25% 25% DC resistance (: )max. Rated current (mA)max. Part No. 0.3 0.3 0.3 400 400 400 HF70ACB322513-T HF50ACB322513-T HF30ACB322513-T * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (13/17) E M C C o m p o n e n t s HFxxACB series HFxxACB3225 Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS HF70ACB322513 HF50ACB322513 1 1 Z 100 Z 100 Z R 10 X R X 100 X 10 R 10 Z, X, R () 100 10 1000 1000 Z, X, R () Z, X, R () 1000 HF30ACB322513 1000 1 1 Frequency (MHz) 10 100 Frequency (MHz) 1000 1 1 10 100 1000 Frequency (MHz) * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (14/17) E M C C o m p o n e n t s HFxxACB series HFxxACB4532 Type SHAPE & DIMENSIONS 4.500.25 1.500.25 Terminal electrode 3.200.25 Ferrite 0.300.20 0.300.20 Insulation resin Dimensions in mm 3.0 RECOMMENDED LAND PATTERN 1.5 3.0 1.5 Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (15/17) E M C C o m p o n e n t s HFxxACB series HFxxACB4532 Type ELECTRICAL CHARACTERISTICS CHARACTERISTICS SPECIFICATION TABLE Impedance [100MHz] (: ) 120 125 70 Tolerance 25% 25% 25% DC resistance (: )max. Rated current (mA)max. Part No. 0.4 0.4 0.4 300 300 300 HF70ACB453215-T HF50ACB453215-T HF30ACB453215-T * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (16/17) E M C C o m p o n e n t s HFxxACB series HFxxACB4532 Type ELECTRICAL CHARACTERISTICS Z, X, R VS. FREQUENCY CHARACTERISTICS HF70ACB453215 HF50ACB453215 1000 Z X R 1000 Z 100 Z, X, R () 100 Z, X, R () Z, X, R () 1000 10 HF30ACB453215 X 10 R Z 100 X 10 R 1 1 10 100 1000 1 1 Frequency (MHz) 10 100 Frequency (MHz) 1000 1 1 10 100 1000 Frequency (MHz) * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm (17/17) E M C C o m p o n e n t s HFxxACB series Packaging style REEL DIMENSIONS 2.00.5 W1 8.4+2.0/-0.0 8.4+2.0/-0.0 8.4+2.0/-0.0 13.00.3 W2 14.4max. 14.4max. 14.4max. 17.01.4 N o60min. o60min. o60min. o61min. N Type HFxxACB2012 HFxxACB3216 HFxxACB3225 HFxxACB4532 1.0 o130.2 W1 o210.8 W2 o1802.0 Dimensions in mm 4.00.1 t B W 2.00.05 F 1.5 +0.1 0 1.750.1 TAPE DIMENSIONS A P1 K Dimensions in mm Type HFxxACB2012 HFxxACB3216 HFxxACB3225 HFxxACB4532 40 to 80 A 1.40.1 1.750.1 2.60.1 3.370.1 Taping B 2.250.1 3.450.1 3.450.1 4.750.1 F 3.50.05 3.50.05 3.50.05 5.50.05 P1 4.00.1 4.00.1 4.00.1 8.00.1 W 8.00.3 8.00.3 8.00.3 12.00.3 K 1.25max. 1.4max. 1.6max. 1.8max. t 0.3max. 0.3max. 0.35max. 0.4max. 200min. Drawing direction 300min. Dimensions in mm * All specifications are subject to change without notice. 001-01 / 20130722 / e9415_hf_acb.fm