LM7805CT - Texas Instruments

Pin 1. Input

2. Ground

3. Output

Tab/Case is Ground or Output

TO-3

SOT-223

TO-220

TO-263

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

LM340, LM340A and LM78xx Wide V

1.5-A Fixed Voltage Regulators

1 Features

1• Output Current up to 1.5 A

• Available in Fixed 5-V, 12-V, and 15-V Options

• Output Voltage Tolerances of ±2% at TJ= 25°C

(LM340A)

• Line Regulation of 0.01% / V of at 1-A Load

(LM340A)

• Load Regulation of 0.3% / A (LM340A)

• Internal Thermal Overload, Short-Circuit and SOA

Protection

• Available in Space-Saving SOT-223 Package

• Output Capacitance Not Required for Stability

2 Applications

• Industrial Power Supplies

• SMPS Post Regulation

• HVAC Systems

• White Goods

SPACE

Available Packages

3 Description

The LM340 and LM78xx monolithic 3-terminal

positive voltage regulators employ internal current-

limiting, thermal shutdown and safe-area

compensation, making them essentially indestructible.

If adequate heat sinking is provided, they can deliver

over 1.5-A output current. They are intended as fixed

voltage regulators in a wide range of applications

including local (on-card) regulation for elimination of

noise and distribution problems associated with

single-point regulation. In addition to use as fixed

voltage regulators, these devices can be used with

external components to obtain adjustable output

voltages and currents.

Considerable effort was expended to make the entire

series of regulators easy to use and minimize the

number of external components. It is not necessary to

bypass the output, although this does improve

transient response. Input bypassing is needed only if

the regulator is located far from the filter capacitor of

the power supply.

LM7805 is also available in a higher accuracy and

better performance version (LM340A). Refer to

LM340A specifications in the LM340A Electrical

Characterisitcs table.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

LM340x

LM78xx

DDPAK/TO-263 (3) 10.18 mm × 8.41 mm

SOT-23 (4) 6.50 mm × 3.50 mm

TO-220 (3) 14.986 mm × 10.16 mm

TO-3 (2) 38.94 mm x 25.40 mm

(1) For all available packages, see the orderable addendum at

the end of the data sheet.

Fixed Output Voltage Regulator

*Required if the regulator is located far from

the power supply filter.

**Although no output capacitor is needed

for stability, it does help transient response.

(If needed, use 0.1-μF, ceramic disc).

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Pin Configuration and Functions......................... 3

6 Specifications......................................................... 4

6.1 Absolute Maximum Ratings ...................................... 4

6.2 ESD Ratings.............................................................. 4

6.3 Recommended Operating Conditions....................... 4

6.4 Thermal Information.................................................. 4

6.5 LM340A Electrical Characteristics,

VO= 5 V, VI= 10 V............................................................ 5

6.6 LM340 / LM7805 Electrical Characteristics,

VO= 5 V, VI= 10 V............................................................ 6

6.7 LM340 / LM7812 Electrical Characteristics,

VO= 12 V, VI= 19 V.......................................................... 7

6.8 LM340 / LM7815 Electrical Characteristics,

VO= 15 V, VI= 23 V.......................................................... 8

6.9 Typical Characteristics.............................................. 9

7 Detailed Description............................................ 12

7.1 Overview................................................................. 12

7.2 Functional Block Diagram....................................... 12

7.3 Feature Description................................................. 12

7.4 Device Functional Modes........................................ 12

8 Application and Implementation ........................ 13

8.1 Application Information............................................ 13

8.2 Typical Applications ................................................ 14

8.3 System Examples ................................................... 15

9 Power Supply Recommendations...................... 17

10 Layout................................................................... 17

10.1 Layout Guidelines ................................................. 17

10.2 Layout Example ................................................... 17

10.3 Heat Sinking DDPAK/TO-263 and SOT-223

Package Parts.......................................................... 18

11 Device and Documentation Support................. 20

11.1 Documentation Support ........................................ 20

11.2 Related Links ........................................................ 20

11.3 Receiving Notification of Documentation Updates 20

11.4 Community Resources.......................................... 20

11.5 Trademarks........................................................... 20

11.6 Electrostatic Discharge Caution............................ 20

11.7 Glossary................................................................ 20

12 Mechanical, Packaging, and Orderable

Information........................................................... 21

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision J (December 2013) to Revision K Page

• Added ESD Ratings table, Thermal Information table, Feature Description section, Device Functional Modes,

Application and Implementation section, Power Supply Recommendations section, Layout section, Device and

Documentation Support section, and Mechanical, Packaging, and Orderable Information section....................................... 1

• Deleted obsolete LM140 and LM7808C devices from the data sheet ................................................................................... 1

• Changed Figure 13 caption from Line Regulation 140AK-5.0 to Line Regulation LM340, .................................................. 11

• Changed Figure 14 caption from Line Regulation 140AK-5.0 to Line Regulation LM340, .................................................. 11

Changes from Revision I (March 2013) to Revision J Page

• Changed 0.5 from typ to max................................................................................................................................................. 5

GND

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

5 Pin Configuration and Functions

LM7805 and LM7812 KTT Package

3-Pin DDPAK/TO-263

Top View

LM7805, LM7812, and LM7815 NDE Package

3-Pin TO-220

Top View

LM7805 DCY Package

4-Pin SOT-223

Side View

LM340K-5.0 NDS Package

2-Pin TO-3

Top View

Pin Functions

PIN I/O DESCRIPTION

NAME NO.

INPUT 1 I Input voltage pin

GND 2 I/O Ground pin

OUTPUT 3 O Output voltage pin

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and

specifications.

(3) The maximum allowable power dissipation at any ambient temperature is a function of the maximum junction temperature for operation

(TJMAX = 125°C or 150°C), the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA). PDMAX = (TJMAX −

TA)/θJA. If this dissipation is exceeded, the die temperature rises above TJMAX and the electrical specifications do not apply. If the die

temperature rises above 150°C, the device goes into thermal shutdown. For the TO-3 package (NDS), the junction-to-ambient thermal

resistance (θJA) is 39°C/W. When using a heat sink, θJA is the sum of the 4°C/W junction-to-case thermal resistance (θJC) of the TO-3

package and the case-to-ambient thermal resistance of the heat sink. For the TO-220 package (NDE), θJA is 54°C/W and θJC is 4°C/W.

If SOT-223 is used, the junction-to-ambient thermal resistance is 174°C/W and can be reduced by a heat sink (see Applications Hints on

heat sinking).If the DDPAK\TO-263 package is used, the thermal resistance can be reduced by increasing the PCB copper area

thermally connected to the package: Using 0.5 square inches of copper area, θJA is 50°C/W; with 1 square inch of copper area, θJA is

37°C/W; and with 1.6 or more inches of copper area, θJA is 32°C/W.

6 Specifications

6.1 Absolute Maximum Ratings

over operating free-air temperature range (unless otherwise noted)(1)(2)

MIN MAX UNIT

DC input voltage 35 V

Internal power dissipation(3) Internally Limited

Maximum junction temperature 150 °C

Lead temperature (soldering, 10 sec.) TO-3 package (NDS) 300 °C

Lead temperature 1,6 mm (1/16 in) from case for 10 s 230 °C

Storage temperature −65 150 °C

(1) ESD rating is based on the human-body model, 100 pF discharged through 1.5 kΩ.

6.2 ESD Ratings VALUE UNIT

V(ESD) Electrostatic

discharge Human-body model (HBM)(1) ±2000 V

6.3 Recommended Operating Conditions

over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT

Temperature (TA) LM340A, LM340 0 125 °C

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report.

6.4 Thermal Information

THERMAL METRIC(1)

LM340, LM78xx

UNIT

NDE

(TO-220) KTT

(DDPAK/TO-263) DCY

(SOT-223) NDS

(TO-3)

3 PINS 3 PINS 4 PINS 2 PINS

RθJA Junction-to-ambient thermal resistance 23.9 44.8 62.1 39 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 16.7 45.6 44 2 °C/W

RθJB Junction-to-board thermal resistance 5.3 24.4 10.7 — °C/W

ψJT Junction-to-top characterization parameter 3.2 11.2 2.7 — °C/W

ψJB Junction-to-board characterization parameter 5.3 23.4 10.6 — °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance 1.7 1.5 — — °C/W

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

(1) All characteristics are measured with a 0.22-μF capacitor from input to ground and a 0.1-μF capacitor from output to ground. All

characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw≤10 ms, duty cycle ≤5%).

Output voltage changes due to changes in internal temperature must be taken into account separately.

6.5 LM340A Electrical Characteristics,

VO= 5 V, VI= 10 V

IOUT = 1 A, 0°C ≤TJ≤125°C (LM340A) unless otherwise specified(1)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VOOutput voltage

TJ= 25°C 4.9 5 5.1 V

PD≤15 W, 5 mA ≤IO≤1 A

7.5 V ≤VIN ≤20 V 4.8 5.2 V

ΔVOLine regulation

7.5 V ≤VIN ≤20

VTJ= 25°C 3 10 mV

Over temperature, IO= 500 mA 10 mV

8 V ≤VIN ≤12 V TJ= 25°C 4 mV

Over temperature 12 mV

ΔVOLoad regulation TJ= 25°C 5 mA ≤IO≤1.5 A 10 25 mV

250 mA ≤IO≤750 mA 15 mV

Over temperature, 5 mA ≤IO≤1 A 25 mV

IQQuiescent current TJ= 25°C 6 mA

Over temperature 6.5 mA

ΔIQQuiescent current

change

TJ= 25°C, IO= 1 A

7.5 V ≤VIN ≤20 V 0.8 mA

Over temperature, 5 mA ≤IO≤1 A 0.5 mA

Over temperature, IO= 500 mA

8 V ≤VIN ≤25 V 0.8 mA

VNOutput noise voltage TA= 25°C, 10 Hz ≤f≤100 kHz 40 μV

Ripple rejection

f = 120 Hz

8 V ≤VIN ≤18

TJ= 25°C, , IO= 1 A 68 80 dB

Over temperature, IO= 500 mA 68 dB

Dropout voltage TJ= 25°C, IO= 1 A 2 V

Output resistance f = 1 kHz 8 mΩ

Short-circuit current TJ= 25°C 2.1 A

Peak output current TJ= 25°C 2.4 A

Average TC of VOMin, TJ= 0°C, IO= 5 mA −0.6 mV/°C

VIN Input voltage required to

maintain line regulation TJ= 25°C 7.5 V

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

(1) All characteristics are measured with a 0.22-μF capacitor from input to ground and a 0.1-μF capacitor from output to ground. All

characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw≤10 ms, duty cycle ≤5%).

Output voltage changes due to changes in internal temperature must be taken into account separately.

6.6 LM340 / LM7805 Electrical Characteristics,

VO= 5 V, VI= 10 V

0°C ≤TJ≤125°C unless otherwise specified(1)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VOOutput voltage

TJ= 25°C, 5 mA ≤IO≤1 A 4.8 5 5.2 V

PD≤15 W, 5 mA ≤IO≤1 A

7.5 V ≤VIN ≤20 V 4.75 5.25 V

ΔVOLine regulation

IO= 500 mA

TJ= 25°C

7V ≤VIN ≤25V 3 50 mV

Over temperature

8V ≤VIN ≤20V 50 mV

IO≤1 A

TJ= 25°C

7.5V ≤VIN ≤20V 50 mV

Over temperature

8V ≤VIN ≤12V 25 mV

ΔVOLoad regulation TJ= 25°C 5 mA ≤IO≤1.5 A 10 50 mV

250 mA ≤IO≤750 mA 25 mV

Over temperature, 5 mA ≤IO≤1 A 50 mV

IQQuiescent current IO≤1 A TJ= 25°C 8 mA

Over temperature 8.5 mA

ΔIQQuiescent current change

0°C ≤TJ≤125°C, 5 mA ≤IO≤1 A 0.5 mA

7 V ≤VIN ≤20 V TJ= 25°C, IO≤1 A 1 mA

Over temperature, IO≤500

mA 1mA

VNOutput noise voltage TA= 25°C, 10 Hz ≤f≤100 kHz 40 μV

Ripple rejection f = 120 Hz

8 V ≤VIN ≤18 V

TJ= 25°C, IO≤1 A 62 80 dB

Over temperature, IO≤500

mA 62 dB

Dropout voltage TJ= 25°C, IO= 1 A 2 V

Output resistance f = 1 kHz 8 mΩ

Short-circuit current TJ= 25°C 2.1 A

Peak output current TJ= 25°C 2.4 A

Average TC of VOUT Over temperature, IO= 5 mA −0.6 mV/°C

VIN Input voltage required to

maintain line regulation TJ= 25°C, IO≤1 A 7.5 V

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

(1) All characteristics are measured with a 0.22-μF capacitor from input to ground and a 0.1-μF capacitor from output to ground. All

characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw≤10 ms, duty cycle ≤5%).

Output voltage changes due to changes in internal temperature must be taken into account separately.

6.7 LM340 / LM7812 Electrical Characteristics,

VO= 12 V, VI= 19 V

0°C ≤TJ≤125°C unless otherwise specified(1)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VOOutput voltage

TJ= 25°C, 5 mA ≤IO≤1 A 11.5 12 12.5 V

PD≤15 W, 5 mA ≤IO≤1 A

14.5 V ≤VIN ≤27 V 11.4 12.6 V

ΔVOLine regulation

IO= 500 mA

TJ= 25°C

14.5V ≤VIN ≤30V 4 120 mV

Over temperature

15V ≤VIN ≤27V 120 mV

IO≤1 A

TJ= 25°C

14.6V ≤VIN ≤27V 120 mV

Over temperature

16V ≤VIN ≤22V 60 mV

ΔVOLoad regulation TJ= 25°C 5 mA ≤IO≤1.5 A 12 120 mV

250 mA ≤IO≤750 mA 60 mV

Over temperature, 5 mA ≤IO≤1 A 120 mV

IQQuiescent current IO≤1 A TJ= 25°C 8 mA

Over temperature 8.5 mA

ΔIQQuiescent current change

5 mA ≤IO≤1 A 0.5 mA

TJ= 25°C, IO≤1 A

14.8 V ≤VIN ≤27 V 1mA

Over temperature, IO≤500 mA

14.5 V ≤VIN ≤30 V 1mA

VNOutput noise voltage TA= 25°C, 10 Hz ≤f≤100 kHz 75 μV

Ripple rejection f = 120 Hz

15 V ≤VIN ≤25

TJ= 25°C, IO≤1 A 55 72 dB

Over temperature, IO≤500

mA, 55 dB

Dropout voltage TJ= 25°C, IO= 1 A 2 V

Output resistance f = 1 kHz 18 mΩ

Short-circuit current TJ= 25°C 1.5 A

Peak output current TJ= 25°C 2.4 A

Average TC of VOUT Over temperature, IO= 5 mA −1.5 mV/°C

VIN Input voltage required to

maintain line regulation TJ= 25°C, IO≤1 A 14.6 V

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

(1) All characteristics are measured with a 0.22-μF capacitor from input to ground and a 0.1-μF capacitor from output to ground. All

characteristics except noise voltage and ripple rejection ratio are measured using pulse techniques (tw≤10 ms, duty cycle ≤5%).

Output voltage changes due to changes in internal temperature must be taken into account separately.

6.8 LM340 / LM7815 Electrical Characteristics,

VO= 15 V, VI= 23 V

0°C ≤TJ≤125°C unless otherwise specified(1)

PARAMETER TEST CONDITIONS MIN TYP MAX UNIT

VOOutput voltage

TJ= 25°C, 5 mA ≤IO≤1 A 14.4 15 15.6 V

PD≤15 W, 5 mA ≤IO≤1 A

17.5 V ≤VIN ≤30 V 14.25 15.75 V

ΔVOLine regulation

IO= 500 mA

TJ= 25°C

17.5 V ≤VIN ≤30 V 4 150 mV

Over temperature

18.5 V ≤VIN ≤30 V 150 mV

IO≤1 A

TJ= 25°C

17.7 V ≤VIN ≤30 V 150 mV

Over temperature

20 V ≤VIN ≤26 V 75 mV

ΔVOLoad regulation TJ= 25°C 5 mA ≤IO≤1.5 A 12 150 mV

250 mA ≤IO≤750 mA 75 mV

Over temperature, 5 mA ≤IO≤1 A, 150 mV

IQQuiescent current IO≤1 A TJ= 25°C 8 mA

Over temperature 8.5 mA

ΔIQQuiescent current change

5 mA ≤IO≤1 A 0.5 mA

TJ= 25°C, IO≤1 A

17.9 V ≤VIN ≤30 V 1mA

Over temperature, IO≤500 mA

17.5 V ≤VIN ≤30 V 1mA

VNOutput noise voltage TA= 25°C, 10 Hz ≤f≤100 kHz 90 μV

Ripple rejection f = 120 Hz

18.5 V ≤VIN ≤

28.5 V

TJ= 25°C, IO≤1 A 54 70 dB

Over temperature, IO≤500

mA, 54 dB

Dropout voltage TJ= 25°C, IO= 1 A 2 V

Output resistance f = 1 kHz 19 mΩ

Short-circuit current TJ= 25°C 1.2 A

Peak output current TJ= 25°C 2.4 A

Average TC of VOUT Over temperature, IO= 5 mA −1.8 mV/°C

VIN Input voltage required to

maintain line regulation TJ= 25°C, IO≤1 A 17.7 V

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

6.9 Typical Characteristics

Figure 1. Maximum Average Power Dissipation Figure 2. Maximum Average Power Dissipation

Figure 3. Maximum Power Dissipation (DDPAK/TO-263)

Shaded area refers to LM340A/LM340, LM7805C, LM7812C and

LM7815C.

Figure 4. Output Voltage (Normalized to 1 V at TJ= 25°C)

Figure 5. Ripple Rejection Figure 6. Ripple Rejection

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Typical Characteristics (continued)

Figure 7. Output Impedance Figure 8. Dropout Characteristics

Shaded area refers to LM340A/LM340, LM7805C, LM7812C, and

LM7815C. Figure 9. Quiescent Current Figure 10. Peak Output Current

Shaded area refers to LM340A/LM340, LM7805C, LM7812C, and

LM7815C. Figure 11. Dropout Voltage Figure 12. Quiescent Current

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Typical Characteristics (continued)

IOUT = 1 A, TA= 25°C

Figure 13. Line Regulation LM340 VIN = 10 V, TA= 25°C

Figure 14. Line Regulation LM340

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

7 Detailed Description

7.1 Overview

The LM340 and LM78xx are a family of fixed output positive voltage regulators with outputs ranging from 3 V to

15 V. They accept up to 35 V of input voltage and with proper heat dissipation can provide over 1.5 A of current.

With a combination of current limiting, thermal shutdown, and safe area protection, these regulators eliminate

any concern of damage. These features paired with excellent line and load regulation make the LM340 and

LM78xx versatile solutions to a wide range of power management designs. Although the LM340N and LM78xx

were designed primarily as fixed-voltage regulators, these devices can be used with external component for

adjustable voltage and current.

7.2 Functional Block Diagram

7.3 Feature Description

7.3.1 Output Current

With proper considerations, the LM340 and LM78xx can exceed 1.5-A output current. Depending on the desired

package option, the effective junction-to-ambient thermal resistance can be reduced through heat sinking,

allowing more power to be dissipated in the device.

7.3.2 Current Limiting Feature

In the event of a short circuit at the output of the regulator, each device has an internal current limit to protect it

from damage. The typical current limits for the LM340 and LM78xx is 2.4 A.

7.3.3 Thermal Shutdown

Each package type employs internal current limiting and thermal shutdown to provide safe operation area

protection. If the junction temperature is allowed to rise to 150°C, the device will go into thermal shutdown.

7.4 Device Functional Modes

There are no functional modes for this device.

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

8 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

8.1 Application Information

The LM340x and LM78xx series is designed with thermal protection, output short-circuit protection, and output

transistor safe area protection. However, as with any IC regulator, it becomes necessary to take precautions to

assure that the regulator is not inadvertently damaged. The following describes possible misapplications and

methods to prevent damage to the regulator.

8.1.1 Shorting the Regulator Input

When using large capacitors at the output of these regulators, a protection diode connected input to output

(Figure 15) may be required if the input is shorted to ground. Without the protection diode, an input short causes

the input to rapidly approach ground potential, while the output remains near the initial VOUT because of the

stored charge in the large output capacitor. The capacitor will then discharge through a large internal input to

output diode and parasitic transistors. If the energy released by the capacitor is large enough, this diode, low

current metal, and the regulator are destroyed. The fast diode in Figure 15 shunts most of the capacitors

discharge current around the regulator. Generally no protection diode is required for values of output capacitance

≤10 μF.

8.1.2 Raising the Output Voltage Above the Input Voltage

Because the output of the device does not sink current, forcing the output high can cause damage to internal low

current paths in a manner similar to that just described in Shorting the Regulator Input.

8.1.3 Regulator Floating Ground

When the ground pin alone becomes disconnected, the output approaches the unregulated input, causing

possible damage to other circuits connected to VOUT. If ground is reconnected with power ON, damage may also

occur to the regulator. This fault is most likely to occur when plugging in regulators or modules with on card

regulators into powered up sockets. The power must be turned off first, the thermal limit ceases operating, or the

ground must be connected first if power must be left on. See Figure 16.

8.1.4 Transient Voltages

If transients exceed the maximum rated input voltage of the device, or reach more than 0.8 V below ground and

have sufficient energy, they will damage the regulator. The solution is to use a large input capacitor, a series

input breakdown diode, a choke, a transient suppressor or a combination of these.

Figure 15. Input Short

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Application Information (continued)

Figure 16. Regulator Floating Ground

Figure 17. Transients

When a value for θ(H–A) is found, a heat sink must be selected that has a value that is less than or equal to this

number.

θ(H–A) is specified numerically by the heat sink manufacturer in this catalog or shown in a curve that plots

temperature rise vs power dissipation for the heat sink.

8.2 Typical Applications

8.2.1 Fixed Output Voltage Regulator

The LM340x and LM78xx devices are primarily designed to provide fixed output voltage regulation. The simplest

implementation of LM340x and LM78xx is shown in Figure 18.

*Required if the regulator is located far from the power supply filter.

**Although no output capacitor is needed for stability, it does help transient response. (If needed, use 0.1-μF, ceramic

disc).

Figure 18. Fixed Output Voltage Regulator

8.2.1.1 Design Requirements

The device component count is very minimal. Although not required, TI recommends employing bypass

capacitors at the output for optimum stability and transient response. These capacitors must be placed as close

as possible to the regulator. If the device is located more than 6 inches from the power supply filter, it is required

to employ input capacitor.

0.1 PF

0.22 PF

OUTPUTINPUT

GND

0.1 PF

0.22 PF

OUTPUTINPUT

GND

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Typical Applications (continued)

8.2.1.2 Detailed Design Procedure

The output voltage is set based on the device variant. LM340x and LM78xx are available in 5-V, 12-V and 15-V

regulator options.

8.2.1.3 Application Curve

Figure 19. VOUT vs VIN, VOUT =5V

8.3 System Examples

IOUT = V2–3 / R1 + IQ

ΔIQ= 1.3 mA over line and load changes. VOUT = 5 V + (5 V/R1 + IQ) R2 5 V/R1 > 3 IQ,

load regulation (Lr)≈[(R1 + R2)/R1] (Lrof LM340-5).

Figure 20. Current Regulator Figure 21. Adjustable Output Regulator

Figure 22. High Input Voltage Circuit With Series

Resistor Figure 23. High Input Voltage Circuit

implementation With Transistor

0.1 PF

OUTPUTINPUT

GND

+ OUT

+ +

0.1 PF

OUTPUTINPUT

GND

- OUT

+ +

LM340

LM79xx

0.1 PF

0.22 PF

OUTPUT

INPUT

GND

3.0:

2N6133

IO MAX

IQ1

IREG

0.1 PF

0.22 PF

OUTPUT

INPUT

GND

OUT

3.0:

2N6132

RSC

2N6124

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

System Examples (continued)

β(Q1) ≥IO Max / IREG Max

R1 = 0.9 / IREG =β(Q1) VBE(Q1) / IREG Max (β+1) – IO Max

RSC = 0.8 / ISC

R1 = βVBE(Q1) / IREG Max (β+1) – IO Max

Figure 24. High Current Voltage Regulator Figure 25. High Output Current With Short-Circuit

Protection

Figure 26. LM340 Used With Negative Regulator LM79xx

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

9 Power Supply Recommendations

The LM340 is designed to operate from a wide input voltage up to 35 V. Please refer to electrical characteristics

tables for the minimum input voltage required for line/load regulation. If the device is more than six inches from

the input filter capacitors, an input bypass capacitor, 0.1 μF or greater, of any type is needed for stability.

10 Layout

10.1 Layout Guidelines

Some layout guidelines must be followed to ensure proper regulation of the output voltage with minimum noise.

Traces carrying the load current must be wide to reduce the amount of parasitic trace inductance. To improve

PSRR, a bypass capacitor can be placed at the OUTPUT pin and must be placed as close as possible to the IC.

All that is required for the typical fixed output regulator application circuit is the LM340x/LM78xx IC and a 0.22-µF

input capacitor if the regulator is placed far from the power supply filter. A 0.1-µF output capacitor is

recommended to help with transient response. In cases when VIN shorts to ground, an external diode must be

placed from VOUT to VIN to divert the surge current from the output capacitor and protect the IC.

10.2 Layout Example

Figure 27. Layout Example DDPAK

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Layout Example (continued)

Figure 28. Layout Example SOT-223

10.3 Heat Sinking DDPAK/TO-263 and SOT-223 Package Parts

Both the DDPAK/TO-263 (KTT) and SOT-223 (DCY) packages use a copper plane on the PCB and the PCB

itself as a heat sink. To optimize the heat sinking ability of the plane and PCB, solder the tab of the plane.

Figure 29 shows for the DDPAK/TO-263 the measured values of θ(J–A) for different copper area sizes using a

typical PCB with 1-oz copper and no solder mask over the copper area used for heat sinking.

Figure 29. θ(J–A) vs Copper (1 Ounce) Area for the DDPAK/TO-263 Package

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

Heat Sinking DDPAK/TO-263 and SOT-223 Package Parts (continued)

As shown in Figure 29, increasing the copper area beyond 1 square inch produces very little improvement. It

should also be observed that the minimum value of θ(J–A) for the DDPAK/TO-263 package mounted to a PCB is

32°C/W.

As a design aid, Figure 30 shows the maximum allowable power dissipation compared to ambient temperature

for the DDPAK/TO-263 device (assuming θ(J–A) is 35°C/W and the maximum junction temperature is 125°C).

Figure 30. Maximum Power Dissipation vs TAMB for the DDPAK/TO-263 Package

Figure 31 and Figure 32 show the information for the SOT-223 package. Figure 31 assumes a θ(J–A) of 74°C/W

for 1-oz. copper and 51°C/W for 2-oz. copper and a maximum junction temperature of 125°C.

Figure 31. θ(J–A) vs Copper (2 Ounce) Area

for the SOT-223 Package Figure 32. Maximum Power Dissipation vs

TAMB for the SOT-223 Package

See AN-1028 LMX2370 PLLatinum Dual Freq Synth for RF Pers Comm LMX2370 2.5GHz/1.2GHz (SNVA036)

for power enhancement techniques to be used with the SOT-223 package.

LM340

LM340A

LM7805

LM7812

LM7815

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

www.ti.com

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

11 Device and Documentation Support

11.1 Documentation Support

11.1.1 Related Documentation

For related documentation, see the following:

•AN-1028 LMX2370 PLLatinum Dual Freq Synth for RF Pers Comm LMX2370 2.5GHz/1.2GHz (SNVA036)

•LM140K Series 3-Terminal Positive Regulators (SNVS994)

11.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 1. Related Links

PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL

DOCUMENTS TOOLS &

SOFTWARE SUPPORT &

COMMUNITY

LM340 Click here Click here Click here Click here Click here

LM340A Click here Click here Click here Click here Click here

LM7805 Click here Click here Click here Click here Click here

LM7812 Click here Click here Click here Click here Click here

LM7815 Click here Click here Click here Click here Click here

11.3 Receiving Notification of Documentation Updates

To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper

right corner, click on Alert me to register and receive a weekly digest of any product information that has

changed. For change details, review the revision history included in any revised document.

11.4 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

11.5 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

11.6 Electrostatic Discharge Caution

These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam

during storage or handling to prevent electrostatic damage to the MOS gates.

11.7 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

LM340

LM340A

LM7805

LM7812

LM7815

www.ti.com

SNOSBT0K –FEBRUARY 2000–REVISED JULY 2016

Product Folder Links: LM340 LM340A LM7805 LM7812 LM7815

12 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 3-Aug-2016

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

LM340AT-5.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 70 LM340AT

5.0 P+

LM340AT-5.0/NOPB ACTIVE TO-220 NDE 3 45 Pb-Free (RoHS

Exempt) CU SN Level-1-NA-UNLIM 0 to 125 LM340AT

5.0 P+

LM340K-5.0 ACTIVE TO-3 NDS 2 50 TBD Call TI Call TI 0 to 125 LM340K

-5.0 7805P+

LM340K-5.0/NOPB ACTIVE TO-3 NDS 2 50 Green (RoHS

& no Sb/Br) Call TI Level-1-NA-UNLIM 0 to 125 LM340K

-5.0 7805P+

LM340MP-5.0 NRND SOT-223 DCY 4 1000 TBD Call TI Call TI 0 to 70 N00A

LM340MP-5.0/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N00A

LM340MPX-5.0/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N00A

LM340S-12/NOPB ACTIVE DDPAK/

TO-263 KTT 3 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-12 P+

LM340S-5.0 NRND DDPAK/

TO-263 KTT 3 45 TBD Call TI Call TI 0 to 70 LM340S

-5.0 P+

LM340S-5.0/NOPB ACTIVE DDPAK/

TO-263 KTT 3 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-5.0 P+

LM340SX-12/NOPB ACTIVE DDPAK/

TO-263 KTT 3 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-12 P+

LM340SX-5.0 NRND DDPAK/

TO-263 KTT 3 500 TBD Call TI Call TI 0 to 70 LM340S

-5.0 P+

LM340SX-5.0/NOPB ACTIVE DDPAK/

TO-263 KTT 3 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-5.0 P+

LM340T-12 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 70 LM340T12

7812 P+

LM340T-12/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM340T12

7812 P+

LM340T-15 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 70 LM340T15

7815 P+

LM340T-15/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM340T15

7815 P+

LM340T-5.0 NRND TO-220 NDE 3 45 TBD Call TI Call TI 0 to 70 LM340T5

PACKAGE OPTION ADDENDUM

www.ti.com 3-Aug-2016

Addendum-Page 2

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

7805 P+

LM340T-5.0/LF01 ACTIVE TO-220 NDG 3 45 Pb-Free (RoHS

Exempt) CU SN Level-4-260C-72 HR 0 to 125 LM340T5

7805 P+

LM340T-5.0/NOPB ACTIVE TO-220 NDE 3 45 Pb-Free (RoHS

Exempt) CU SN Level-1-NA-UNLIM 0 to 125 LM340T5

7805 P+

LM7805CT ACTIVE TO-220 NDE 3 45 TBD Call TI Call TI 0 to 125 LM340T5

7805 P+

LM7805CT/NOPB ACTIVE TO-220 NDE 3 45 Pb-Free (RoHS

Exempt) CU SN Level-1-NA-UNLIM 0 to 125 LM340T5

7805 P+

LM7805MP/NOPB ACTIVE SOT-223 DCY 4 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N00A

LM7805MPX/NOPB ACTIVE SOT-223 DCY 4 2000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 125 N00A

LM7805S/NOPB ACTIVE DDPAK/

TO-263 KTT 3 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-5.0 P+

LM7805SX/NOPB ACTIVE DDPAK/

TO-263 KTT 3 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-5.0 P+

LM7812CT/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM340T12

7812 P+

LM7812S/NOPB ACTIVE DDPAK/

TO-263 KTT 3 45 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-12 P+

LM7812SX/NOPB ACTIVE DDPAK/

TO-263 KTT 3 500 Pb-Free (RoHS

Exempt) CU SN Level-3-245C-168 HR 0 to 125 LM340S

-12 P+

LM7815CT/NOPB ACTIVE TO-220 NDE 3 45 Green (RoHS

& no Sb/Br) CU SN Level-1-NA-UNLIM 0 to 125 LM340T15

7815 P+

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

PACKAGE OPTION ADDENDUM

www.ti.com 3-Aug-2016

Addendum-Page 3

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

LM340MP-5.0 SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LM340MP-5.0/NOPB SOT-223 DCY 4 1000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LM340MPX-5.0/NOPB SOT-223 DCY 4 2000 330.0 16.4 7.0 7.5 2.2 12.0 16.0 Q3

LM340SX-12/NOPB DDPAK/

TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LM340SX-5.0 DDPAK/

TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

LM340SX-5.0/NOPB DDPAK/

TO-263 KTT 3 500 330.0 24.4 10.75 14.85 5.0 16.0 24.0 Q2

PACKAGE MATERIALS INFORMATION

www.ti.com 3-Nov-2015

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

LM340MP-5.0 SOT-223 DCY 4 1000 367.0 367.0 35.0

LM340MP-5.0/NOPB SOT-223 DCY 4 1000 367.0 367.0 35.0

LM340MPX-5.0/NOPB SOT-223 DCY 4 2000 367.0 367.0 35.0

LM340SX-12/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0

LM340SX-5.0 DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0

LM340SX-5.0/NOPB DDPAK/TO-263 KTT 3 500 367.0 367.0 45.0

PACKAGE MATERIALS INFORMATION

www.ti.com 3-Nov-2015

Pack Materials-Page 2

MECHANICAL DATA

NDS0002A

www.ti.com

MECHANICAL DATA

NDE0003B

www.ti.com

MECHANICAL DATA

NDG0003F

www.ti.com

T03F (Rev B)

MECHANICAL DATA

MPDS094A – APRIL 2001 – REVISED JUNE 2002

POST OFFICE BOX 655303 • DALLAS, TEXAS 75265

DCY (R-PDSO-G4) PLASTIC SMALL-OUTLINE

4202506/B 06/2002

6,30 (0.248)

6,70 (0.264)

2,90 (0.114)

3,10 (0.122)

6,70 (0.264)

7,30 (0.287) 3,70 (0.146)

3,30 (0.130)

0,02 (0.0008)

0,10 (0.0040)

1,50 (0.059)

1,70 (0.067)

0,23 (0.009)

0,35 (0.014)

1 2 3

0,66 (0.026)

0,84 (0.033)

1,80 (0.071) MAX

Seating Plane

0°–10°

Gauge Plane

0,75 (0.030) MIN

0,25 (0.010)

0,08 (0.003)

0,10 (0.004) M

2,30 (0.091)

4,60 (0.181) M

0,10 (0.004)

NOTES: A. All linear dimensions are in millimeters (inches).

B. This drawing is subject to change without notice.

C. Body dimensions do not include mold flash or protrusion.

D. Falls within JEDEC TO-261 Variation AA.

MECHANICAL DATA

KTT0003B

www.ti.com

BOTTOM SIDE OF PACKAGE

TS3B (Rev F)

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other

changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest

issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and

complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale

supplied at the time of order acknowledgment.

TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms

and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary

to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily

performed.

TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and

applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide

adequate design and operating safeguards.

TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or

other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information

published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or

endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the

third party, or a license from TI under the patents or other intellectual property of TI.

Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration

and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered

documentation. Information of third parties may be subject to additional restrictions.

Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service

voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.

TI is not responsible or liable for any such statements.

Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements

concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support

that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which

anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause

harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use

of any TI components in safety-critical applications.

In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to

help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and

requirements. Nonetheless, such components are subject to these terms.

No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties

have executed a special agreement specifically governing such use.

Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in

military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components

which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and

regulatory requirements in connection with such use.

TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of

non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.

Products Applications

Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive

Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications

Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers

DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps

DSP dsp.ti.com Energy and Lighting www.ti.com/energy

Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial

Interface interface.ti.com Medical www.ti.com/medical

Logic logic.ti.com Security www.ti.com/security

Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense

Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video

RFID www.ti-rfid.com

OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com

Wireless Connectivity www.ti.com/wirelessconnectivity

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Texas Instruments:

LM7805CT/LB01 LM7805CT/LF01