SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 D 15-V Digital or 7.5-V Peak-to-Peak D D D D D D D D D Matched Control-Input to Signal-Output Switching 125- Typical On-State Resistance for 15-V Operation Switch On-State Resistance Matched to Within 5 Over 15-V Signal-Input Range On-State Resistance Flat Over Full Peak-to-Peak Signal Range High On/Off Output-Voltage Ratio: 80 dB Typical at fis = 10 kHz, RL = 1 k High Degree of Linearity: <0.5% Distortion Typical at fis = 1 kHz, Vis = 5 V p-p, VDD - VSS 10 V, RL = 10 k Extremely Low Off-State Switch Leakage, Resulting in Very Low Offset Current and High Effective Off-State Resistance: 10 pA Typical at VDD - VSS = 10 V, TA = 25C Extremely High Control Input Impedance (Control Circuit Isolated From Signal Circuit): 1012 Typical Low Crosstalk Between Switches: -50 dB Typical at fis = 8 MHz, RL = 1 k D D D D D Capacitance: Reduces Output Signal Transients Frequency Response, Switch On = 40 MHz Typical 100% Tested for Quiescent Current at 20 V 5-V, 10-V, and 15-V Parametric Ratings Meets All Requirements of JEDEC Tentative Standard No. 13-B, Standard Specifications for Description of "B" Series CMOS Devices Applications: - Analog Signal Switching/Multiplexing: Signal Gating, Modulator, Squelch Control, Demodulator, Chopper, Commutating Switch - Digital Signal Switching/Multiplexing - Transmission-Gate Logic Implementation - Analog-to-Digital and Digital-to-Analog Conversion - Digital Control of Frequency, Impedance, Phase, and Analog-Signal Gain E, F, M, NS, OR PW PACKAGE (TOP VIEW) SIG A IN/OUT SIG A OUT/IN SIG B OUT/IN SIG B IN/OUT CONTROL B CONTROL C VSS 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VDD CONTROL A CONTROL D SIG D IN/OUT SIG D OUT/IN SIG C OUT/IN SIG C IN/OUT description/ordering information The CD4066B is a quad bilateral switch intended for the transmission or multiplexing of analog or digital signals. It is pin-for-pin compatible with the CD4016B, but exhibits a much lower on-state resistance. In addition, the on-state resistance is relatively constant over the full signal-input range. The CD4066B consists of four bilateral switches, each with independent controls. Both the p and the n devices in a given switch are biased on or off simultaneously by the control signal. As shown in Figure 1, the well of the n-channel device on each switch is tied to either the input (when the switch is on) or to VSS (when the switch is off). This configuration eliminates the variation of the switch-transistor threshold voltage with input signal and, thus, keeps the on-state resistance low over the full operating-signal range. The advantages over single-channel switches include peak input-signal voltage swings equal to the full supply voltage and more constant on-state impedance over the input-signal range. However, for sample-and-hold applications, the CD4016B is recommended. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2003, Texas Instruments Incorporated !" #!$% &"' &! #" #" (" " ") !" && *+' &! #", &" ""%+ %!&" ", %% #""' POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 1 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 description/ordering information (continued) ORDERING INFORMATION -55C to 125C ORDERABLE PART NUMBER PACKAGE TA TOP-SIDE MARKING CDIP - F Tube of 25 CD4066BF3A CD4066BF3A PDIP - E Tube of 25 CD4066BE CD4066BE Tube of 50 CD4066BM Reel of 2500 CD4066BM96 Reel of 250 CD4066BMT Reel of 2000 CD4066BNSR Tube of 90 CD4066BPW Reel of 2000 CD4066BPWR SOIC - M SOP - NS TSSOP - PW CD4066BM CD4066B CM066B Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Switch Control In Vis p n p n Control VC Out Vos n VSS VDD VSS All control inputs are protected by the CMOS protection network. NOTES: A. All p substrates are connected to VDD. B. Normal operation control-line biasing: switch on (logic 1), VC = VDD; switch off (logic 0), VC = VSS C. Signal-level range: VSS Vis VDD 92CS-29113 Figure 1. Schematic Diagram of One-of-Four Identical Switches and Associated Control Circuitry 2 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 absolute maximum ratings over operating free-air temperature (unless otherwise noted) DC supply-voltage range, VDD (voltages referenced to VSS terminal) . . . . . . . . . . . . . . . . . . . . -0.5 V to 20 V Input voltage range, Vis (all inputs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 V to VDD + 0.5 V DC input current, IIN (any one input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 mA Package thermal impedance, JA (see Note 1): E package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80C/W M package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86C/W NS package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76C/W PW package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113C/W Lead temperature (during soldering): At distance 1/16 1/32 inch (1,59 0,79 mm) from case for 10 s max . . . . . . . . . . . . . . . . . . . . . . . 265C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65C to 150C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions MIN VDD TA Supply voltage Operating free-air temperature POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MAX UNIT 3 18 V -55 125 C 3 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 electrical characteristics LIMITS AT INDICATED TEMPERATURES PARAMETER IDD TEST CONDITIONS Quiescent device current VIN (V) VDD (V) UNIT 25C -55C -40C 85C 125C TYP MAX 0, 5 5 0.25 0.25 7.5 7.5 0.01 0.25 0, 10 10 0.5 0.5 15 15 0.01 0.5 0, 15 15 1 1 30 30 0.01 1 0, 20 20 5 5 150 150 0.02 5 5 800 850 1200 1300 470 1050 10 310 330 500 550 180 400 15 200 210 300 320 125 240 A A Signal Inputs (Vis) and Outputs (Vos) ron On-state resistance (max) VC = VDD, RL = 10 k returned V DD * V SS to , 2 Vis = VSS to VDD ron THD Iis 4 15 10 10 15 5 On-state resistance difference between any two switches RL = 10 k, VC = VDD Total harmonic distortion VC = VDD = 5 V, VSS = -5 V, Vis(p-p) = 5 V (sine wave centered on 0 V), RL = 10 k, fis = 1-kHz sine wave 0.4 % -3-dB cutoff frequency (switch on) VC = VDD = 5 V, VSS = -5 V, Vis(p-p) = 5 V (sine wave centered on 0 V), RL = 1 k 40 MHz -50-dB feedthrough frequency (switch off) VC = VSS = -5 V, Vis(p-p) = 5 V (sine wave centered on 0 V), RL = 1 k 1 MHz Input/output leakage current (switch off) (max) VC = 0 V, Vis = 18 V, Vos = 0 V; and VC = 0 V, Vis = 0 V, Vos = 18 V VC(A) = VDD = 5 V, VC(B) = VSS = -5 V, Vis(A) = 5 Vp-p, 50- source, RL = 1 k -50-dB crosstalk frequency tpd 5 Propagation delay (signal input to signal output) Cis Input capacitance Cos Cios RL = 200 k, VC = VDD, VSS = GND, CL = 50 pF, Vis = 10 V (square wave centered on 5 V), tr, tf = 20 ns 18 0.1 0.1 1 1 10-5 0.1 8 A MHz 5 20 40 10 10 20 15 7 15 ns 8 pF Output capacitance VDD = 5 V, VC = VSS = -5 V VDD = 5 V, VC = VSS = -5 V 8 pF Feedthrough VDD = 5 V, VC = VSS = -5 V 0.5 pF POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 electrical characteristics (continued) LIMITS AT INDICATED TEMPERATURES CHARACTERISTIC TEST CONDITIONS UNIT 25C VDD (V) -55C -40C 85C 125C TYP MAX Control (VC) VILC Control input, low voltage (max) |Iis| < 10 A, Vis = VSS, VOS = VDD, and Vis = VDD, VOS = VSS 5 1 1 1 1 1 10 2 2 2 2 2 15 2 2 2 2 2 5 VIHC IIN Control input, high voltage 3.5 (MIN) 10 7 (MIN) 15 11 (MIN) V Input current (max) Vis VDD, VDD - VSS = 18 V, VCC VDD - VSS 18 Crosstalk (control input to signal output) VC = 10 V (square wave), tr, tf = 20 ns, RL = 10 k 10 50 5 35 70 Turn-on and turn-off propagation delay VIN = VDD, tr, tf = 20 ns, CL = 50 pF, RL = 1 k 10 20 40 15 15 30 5 6 10 9 15 9.5 Maximum control input repetition rate CI See Figure 6 Vis = VDD, VSS = GND, RL = 1 k to GND, CL = 50 pF, VC = 10 V (square wave centered on 5 V), tr, tf = 20 ns, Vos = 1/2 Vos at 1 kHz V 0.1 0.1 1 1 10-5 Input capacitance 5 0.1 A mV ns MHz 7.5 pF switching characteristics SWITCH OUTPUT, Vos (V) SWITCH INPUT VDD (V) Vis (V) Iis (mA) -55C -40C 25C 85C 125C 5 0 0.64 0.61 0.51 0.42 0.36 5 5 -0.64 -0.61 -0.51 -0.42 -0.36 10 0 1.6 1.5 1.3 1.1 0.9 10 10 -1.6 -1.5 -1.3 -1.1 -0.9 15 0 4.2 4 3.4 2.8 2.4 15 15 -4.2 -4 -3.4 -2.8 -2.4 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 MIN MAX 0.4 4.6 0.5 9.5 1.5 13.5 5 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) 600 Supply Voltage (VDD - VSS) = 5 V 500 TA = 125C 400 300 +25C 200 -55C 100 0 -4 -3 -2 -1 0 1 2 3 4 r - Channel On-State Resistance - on r - Channel On-State Resistance - on TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) 300 Supply Voltage (VDD - VSS) = 10 V 250 TA = 125C 200 +25C 150 -55C 100 50 0 -10 -7.5 -5 -2.5 0 2.5 5 7.5 Vis - Input Signal Voltage - V Vis - Input Signal Voltage - V 92CS-27327RI 92CS-27326RI Figure 2 Figure 3 Supply Voltage (VDD - VSS) = 15 V 300 250 200 TA = 125C 150 +25C 100 -55C 50 0 -7.5 -5 -2.5 0 2.5 5 7.5 10 TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) r - Channel On-State Resistance - on r - Channel On-State Resistance - on TYPICAL ON-STATE RESISTANCE vs INPUT SIGNAL VOLTAGE (ALL TYPES) -10 TA = 125C 600 Supply Voltage (VDD - VSS) = 5 V 500 400 300 200 10 V -15 V 100 0 -10 -7.5 -5 -2.5 0 2.5 5 7.5 10 Vis - Input Signal Voltage - V Vis - Input Signal Voltage - V 92CS-27329RI 92CS-27330RI Figure 5 Figure 4 6 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS Iis Vis CD4066B 1 of 4 Switches ron = Vos |Vis - Vos| |Iis| 92CS-30966 Figure 6. Determination of ron as a Test Condition for Control-Input High-Voltage (VIHC) Specification Keithley 160 Digital Multimeter VDD TG On 10 k 1-k Range Y X-Y Plotter VSS H. P. Moseley 7030A X 92CS-22716 Figure 7. Channel On-State Resistance Measurement Circuit POWER DISSIPATION PER PACKAGE vs SWITCHING FREQUENCY TYPICAL ON CHARACTERISTICS FOR 1 OF 4 CHANNELS 3 VO - Output Voltage - V 2 1 0 VC = VDD -1 Vis CD4066B 1 of 4 Switches Vos RL VSS -2 -3 -3 VDD All unused terminals are connected to VSS -2 -1 0 1 2 3 PD - Power Dissipation Per Package - W 104 4 6 4 TA = 25C 2 103 Supply Voltage (VDD) = 15 V 6 4 2 10 V 102 5V 6 4 14 5 2 6 101 12 6 4 13 CD4066B 7 2 10 10 VDD 2 VI - Input Voltage - V 4 6 102 2 4 VSS 6 103 f - Switching Frequency - kHz 92CS-30919 Figure 9 Figure 8 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 92C-30920 7 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS Cios VDD = 5 V VC = -5 V CD4066B 1 of 4 Switches VC = VSS Vis = VDD Cis VSS = -5 V Cos Figure 10. Typical On Characteristics for One of Four Channels Vos I 92CS-30922 All unused terminals are connected to VSS. Figure 11. Off-Switch Input or Output Leakage VDD VC = VDD Vis CD4066B 1 of 4 Switches VSS 92CS-30921 Measured on Boonton capacitance bridge, model 75a (1 MHz); test-fixture capacitance nulled out. VDD CD4066B 1 of 4 Switches VSS +10 V Vos 50 pF VC tr = tf = 20 ns 200 k VDD VDD V Vis CD4066B os 1 of 4 Switches 10 k 1 k VSS tr = tf = 20 ns 92CS-30924 92CS-30923 All unused terminals are connected to VSS. All unused terminals are connected to VSS. Figure 12. Propagation Delay Time Signal Input (Vis) to Signal Output (Vos) 8 POST OFFICE BOX 655303 Figure 13. Crosstalk-Control Input to Signal Output * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS VDD VDD VC = VDD tr = tf = 20 ns CD4066B 1 of 4 Switches VDD VSS Vos 50 pF 1 k NOTES: A. All unused terminals are connected to VSS. B. Delay is measured at Vos level of +10% from ground (turn-on) or on-state output level (turn-off). 92CS-30925 Figure 14. Propagation Delay, tPLH, tPHL Control-Signal Output tr VC 10% tf 10 V 90% 50% 0V Repetition Rate tr = tf = 20 ns Vos V OS + V OS at 1 kHz 2 VDD = 10 V VC Vis = 10 V CD4066B 1 of 4 Switches V OS + 50 pF V OS at 1 kHz 2 1 k VSS All unused terminals are connected to VSS. 92CS-30925 Figure 15. Maximum Allowable Control-Input Repetition Rate POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 9 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS VDD Inputs VDD I VSS 92CS-27555 VSS Measure inputs sequentially to both VDD and VSS. Connect all unused inputs to either VDD or VSS. Measure control inputs only. Figure 16. Input Leakage-Current Test Circuit 10 10 Clock Reset 14 2 P E J1 7 9 12 J2 J3 J4 J5 Clock CD4018B 15 1 3 External Reset 13 14 P E J1 15 1/4 CD4066B 1 4 3 7 9 12 J2 J3 J4 J5 CD4018B Q1 Q2 1 Q1 Q2 5 2 5 2 4 13 1 3 7 2 2 1/3 CD4049B 5 6 4 8 9 8 6 5 2 1 1/3 CD4049B 5 CD4001B 3 12 6 4 9 CD4001B 10 10 11 4 3 10 9 6 12 5 12 13 6 5 Signal Outputs 11 11 13 Signal Inputs 11 12 Channel 1 Channel 2 4 Channel 3 CD4066B 5 9 11 10 3 4 4 Channel 4 1/4 CD4066B 3 8 9 10 k Maximum Allowable Signal Level LPF Channel 2 10 k CD4066B 11 Package Count 2 - CD4001B 1 - CD4049B 3 - CD4066B 2 - CD4018B Channel 1 1 3 8 LPF 10 k 1/6 CD4049B 2 1 2 12 LPF Channel 3 10 k VDD Clock 30% (VDD - VSS) VSS 10 LPF Channel 4 10 k Chan 1 Chan 2 Chan 3 Chan 4 92CM-30928 Figure 17. Four-Channel PAM Multiplex System Diagram 10 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 TYPICAL CHARACTERISTICS 5V 0 -5 V Analog Inputs (5 V) VDD = 5 V VDD = 5 V CD4066B 5V SWA 0 IN SWB CD4054B SWC SWD Digital Control Inputs VSS = 0 V VEE = -5 V Analog Outputs (5 V) VSS = -5 V 92CS-30927 Figure 18. Bidirectional Signal Transmission Via Digital Control Logic POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 11 SCHS051D - NOVEMBER 1998 - REVISED SEPTEMBER 2003 APPLICATION INFORMATION In applications that employ separate power sources to drive VDD and the signal inputs, the VDD current capability should exceed VDD/RL (RL = effective external load of the four CD4066B bilateral switches). This provision avoids any permanent current flow or clamp action on the VDD supply when power is applied or removed from the CD4066B. In certain applications, the external load-resistor current can include both VDD and signal-line components. To avoid drawing VDD current when switch current flows into terminals 1, 4, 8, or 11, the voltage drop across the bidirectional switch must not exceed 0.8 V (calculated from ron values shown). No VDD current will flow through RL if the switch current flows into terminals 2, 3, 9, or 10. 12 POST OFFICE BOX 655303 * DALLAS, TEXAS 75265 PACKAGE OPTION ADDENDUM www.ti.com 25-Jan-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD4066BEE4 ACTIVE PDIP N 14 25 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type CD4066BF ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type CD4066BF3A ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type CD4066BF3AS2283 OBSOLETE CDIP J 14 TBD Call TI Call TI CD4066BF3AS2534 OBSOLETE CDIP J 14 Call TI Call TI CD4066BM ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BM96 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BM96E4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BM96G4 ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BME4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMG4 ACTIVE SOIC D 14 50 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMT ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMTE4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BMTG4 ACTIVE SOIC D 14 250 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BNSR ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BNSRE4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BNSRG4 ACTIVE SO NS 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPW ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Addendum-Page 1 Samples (Requires Login) CD4066BE TBD (3) PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 25-Jan-2012 Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) CD4066BPWE4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWG4 ACTIVE TSSOP PW 14 90 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWR ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWRE4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM CD4066BPWRG4 ACTIVE TSSOP PW 14 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM JM38510/05852BCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type M38510/05852BCA ACTIVE CDIP J 14 1 TBD A42 N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE OPTION ADDENDUM www.ti.com 25-Jan-2012 OTHER QUALIFIED VERSIONS OF CD4066B, CD4066B-MIL : * Catalog: CD4066B * Automotive: CD4066B-Q1, CD4066B-Q1 * Military: CD4066B-MIL NOTE: Qualified Version Definitions: * Catalog - TI's standard catalog product * Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects * Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant CD4066BM96 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD4066BM96 SOIC D 14 2500 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD4066BMT SOIC D 14 250 330.0 16.4 6.5 9.0 2.1 8.0 16.0 Q1 CD4066BNSR SO NS 14 2000 330.0 16.4 8.2 10.5 2.5 12.0 16.0 Q1 CD4066BPWR TSSOP PW 14 2000 330.0 12.4 6.9 5.6 1.6 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CD4066BM96 SOIC D 14 2500 367.0 367.0 38.0 CD4066BM96 SOIC D 14 2500 333.2 345.9 28.6 CD4066BMT SOIC D 14 250 367.0 367.0 38.0 CD4066BNSR SO NS 14 2000 367.0 367.0 38.0 CD4066BPWR TSSOP PW 14 2000 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated