RHRD660S9A-F085 - FAIRCHILD SEMICONDUCTOR

One world. One KEMET

Overview

KEMET’s 900 series encapsulated radial leaded ceramic

disc capacitors are specically designed for interference-

suppression AC line ltering applications. Having interna-

tionally recognized safety certications, these capacitors

are well-suited for applications that require keeping poten-

tially disruptive or damaging line transients and EMI out

of susceptible equipment. They are also an ideal solution

when needing to suppress line disturbances at the source.

Safety Certied Capacitors are classied as either X and/or

Y capacitors. Class X capacitors are primarily used in line-to

line (across-the-line) applications. In this application there is

no danger of electric shock to humans should the capacitor

fail, but could result in a risk of re. The class Y capacitor is

primarily used in line-to-ground (line by-pass) applications. In

this application, failure of the capacitor could lead to danger

of electric shock.

With a working voltage of 400 VAC in line-to-line (Class X)

and 250 VAC in line-to-ground (Class Y) applications, these

safety capacitors meet the impulse test criteria outlined in

IEC Standard 60384. Meeting subclass X1 and Y2 require-

ments, these devices are certied to withstand impulses up

to 4 KV (X1) and 5 KV (Y2) respectively. These encapsulated

devices also meet the ame test requirements outlined in UL

Standard 94V–0.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated,

AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Ordering Information

C9 8 1 U 103 M Y V D A A 7317

Ceramic

Series

Body

Diameter

Lead

Spacing1,2,4 Spec.

Capacitance

Code (pF)

Capacitance

Tolerance

Rated

Voltage

Dielectric/

Temp. Char.

Design

Lead

Cong.1,3,4

Failure

Rate

Packaging

(C-Spec)

C9 =

Ceramic

900

Series

0 = 7.0 mm

1 = 8.0 mm

2 = 9.0 mm

3 = 10.0 mm

4 = 11.0 mm

6 = 13.0 mm

8 = 15.0 mm

5 = 5.0 mm

7 = 7.5 mm

1 = 10.0 mm

U =

Safety

Two

signicant

digits and

number of

zeroes

J = ±5%

K = ±10%

M = ±20%

Y = X1

400 VAC

/Y2 250

VAC

S = SL

Y = Y5P

W = Y5U

V = Y5V

D =

Disc

A = Straight

B = Vertical

Kink

C = Outside

Kink

D = Inside

Kink

A =

N/A

See

"Packaging

C-Spec

Ordering

Options

Table"

below

1 Due to a high risk of arcing, "Inside Kink" lead conguration cannot be combined with the 5 mm lead spacing option. The "Inside Kink" option is only

available on capacitors with lead spacing of 7.5 mm or greater. A potential for arcing may exist when combining the "Inside Kink" lead conguration

with a 7.5mm lead spacing option, especially in high humidity environments and/or when exposure to voltages and transients may impact creepage and

clearance requirements.

2 Capacitor body diameter will limit available lead spacing and packaging options. See "Dimensions" and "Product Ordering Codes and Ratings" sections

of this document to determine availability.

3 "Vertical Kink", "Outside Kink" and "Inside Kink" lead congurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead

length is only available on capacitors with straight leads (lead conguration ordering code "A"). For nonstandard lead length inquiries, please contact

KEMET.

4 Bulk packaging lead length availability is dependent upon "Lead Conguration" and "Lead Spacing." See "Dimensions" section of this document to

verify availability of a specic lead length option. For nonstandard lead length inquiries, please contact KEMET.

Click image above for interactive 3D content

Open PDF in Adobe Reader for full functionality

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Packaging C-Spec Ordering Options Table

Packaging Type Lead Length

(mm)2,3

Packaging

Ordering Code (C-Spec)

Ammo Pack 20.0 +1.5/−1.0 (straight leads)

18.0 +2.0/−0 (preformed leads1)7317

Bulk Bag

3.0±1.0

WL30

3.5±1.0

WL35

4.0±1.0

WL40

4.5±1.0

WL45

5.0±1.0

WL50

20.0 minimum

WL20

1 Preformed (crimped) lead congurations include vertical kink, outside kink and inside kink. See "Lead Congurations" and "Ordering Information"

sections of this document for further details.

2 "Vertical Kink", "Outside Kink" and "Inside Kink" lead congurations cannot be combined with the bulk/20 mm lead length option (WL20). 20 mm lead

length is only available on capacitors with straight leads (lead conguration ordering code "A"). For nonstandard lead length inquiries, please contact

KEMET.

3 For nonstandard lead length inquiries, please contact KEMET.

4 Lead length of 20.0 mm minimum only available for straight leads.

Benets

• Safety Standard Recognized (IEC 60384–14)

• Reliable operation up to 125°C

• Class X1/Y2

• 5.0 mm, 7.5 mm, and 10 mm lead spacing

• Lead (Pb)-free and RoHS Compliant

• Halogen free

• Capacitance offerings ranging from 10 pF up to 10 nF

• Available capacitance tolerances of ±5%, ±10%, and ±20%

• High reliability

• Preformed (crimped) or straight lead congurations

• Non-polar device, minimizing installation concerns

• Encapsulation meets ammability standard UL 94V–0

Applications

Typical applications include:

• Line-to-line (Class X) ltering

• Line-to-ground (Class Y) ltering

• Antenna coupling

• Primary and secondary coupling (switching power supplies)

• Line disturbances suppression (motors and motor controls, relays, switching power supplies, and inverters)

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Lead Congurations

Straight Vertical Kink Outside Kink Inside Kink1

3.0

Maximum

4.0 Maximum

3.0

Maximum

5.0 Maximum

3.0

Maximum

5.0 Maximum

3.0

Maximum

1 Due to a high risk of arcing, the "Inside Kink" lead conguration option cannot me combined with 5 mm lead spacing ("S" dimension above). The "Inside

Kink" option is only available on devices with lead spacing of 7.5 mm or 10 mm.

Dimensions – Millimeters

Lead

Conguration

Lead

Conguration

Ordering Code1

SLead

Spacing

Tolerance

D T e ØF

Lead

Spacing2

Body

Diameter2

Body

Thickness

Lead

Meniscus

Lead

Diameter

Straight A

5.0 ±0.8

See Table 1 –

"Product Ordering Codes

and Ratings"

3.0

maximum 0.55 ±0.1

7.5 ±1.0

10.0 ±1.0

Vertical Kink

(Preformed) B

5.0 ±0.8

7.5 ±1.0

10.0 ±1.0

Outside Kink

(Preformed) C

5.0 ±0.8

7.5 ±1.0

10.0 ±1.0

Inside Kink

(Preformed) D7.5 ±1.0

10.0 ±1.0

1 Lead Conguration is identied in the 13th character of the ordering code. See "Lead Conguration" and "Ordering Information" sections of this

document for further details.

2 Body diameter of capacitor will limit available lead spacing and packaging options. See "Product Ordering Codes and Ratings" sections of this

document for further details.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Approval Standard and Certication No.

Safety Standard Standard No. Subclass Working Voltage Certicate No.

VDE

(ENEC) IEC 60384–14 X1 400 VAC 40036417

Y2 250 VAC

CAN/CSA

UL 60384–14 and

E60384–14

X1 400VAC E356389

Y2 250VAC

These devices are VDE/ENEC and UL recognized for antenna coupling and AC line-to-line (Class X) and line-to-ground (Class Y) applications per

IEC60384–14 and UL 60384–14.

Environmental Compliance

These devices are Halogen free and RoHS Compliant. They meet all requirements set forth by both EU and China RoHS

directives.

General Specications/Performance Characteristics

Dielectric/Temperature Characteristic SL Y5P Y5U Y5V

Operating Temperature Range: −40°C to +125°C

Capacitance Change with Reference to

+25°Cand 0 VDC Applied (TCC):

−1,000 ~ +350 ppm/

ºC ±10% +20%/−55% ~ +30%/−80%

Dielectric Withstanding Voltage (7.5 mm and 10 mm

Lead Spacing)1

2,600 VAC

(60±5 seconds at 25ºC)

Dielectric Withstanding Voltage (5 mm Lead

Spacing)1

2,000 VAC

(60±5 seconds at 25ºC)

Quality Factor (Q)

30 pF and above:

≥ 1,000

Below 30 pF: ≥ 400

+(20xC)*

See “Dissipation Factor”

Dissipation Factor (tanδ) at +25ºC1See “Quality Factor” 2.50% 2.50% 5.0%

Insulation Resistance (IR) Limit at +25°C 10,000 MΩ Minimum

(500 VDC applied for 60±5 seconds at 25°C)

*C = Nominal capacitance

1 The distance between the adjacent leads of the component (also referred to as "lead spacing") governs Dielectric Withstanding Voltage (DWV) limit.

2 Capacitance and Dissipation Factor (DF) measured under the following conditions:

SL: 1 MHz ± 100 kHz and 1.0 ±0.2 Vrms

X5P, Y5U and Y5V: 1 kHz ± 50 Hz and 1.0 ±0.2 Vrms

Note: When measuring capacitance, it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known

as Automatic Level Control (ALC). The ALC feature should be switched to "ON."

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Table 1 – Product Ordering Codes and Ratings

(1) To properly complete ordering code, insert the one-digit numeric code to reect required lead spacing: (Note that select capacitance values and packaging

options may limit lead spacing availability. See table above to verify availability.)

5 = 5.0 mm

7 = 7.5 mm

1 = 10.0 mm

(2) To properly complete ordering code, insert the one-digit character code to reect the required lead conguration: (See "Lead Conguration" section of this

document, page 2, for further details.)

A = Straight

B = Vertical Kink

C = Outside Kink

D = Inside Kink (not available with 5 mm lead spacing option)

(3) To properly complete ordering code, enter the four-digit numeric or alphanumeric "Packaging C-Spec Ordering Code." See "Dimensions" section of this

document, page 2, for available options.

Dielectric/

Temp. Char.

KEMET

Part Number Capacitance Capacitance

Tolerance

Dimensions (mm) Lead Spacing

Body Diameter

(Maximum)

Body Thickness

(Maximum)

Lead

Diameter

Bulk

Packaging

Ammo

Packaging

C90(1)U100JYSD(2)A(3) 10 pF

±5%

7.0

5.0 0.55 ±0.1

5 mm,

7.5 mm,

10 mm

C90(1)U120JYSD(2)A(3) 12 pF

C90(1)U150JYSD(2)A(3) 15 pF

C90(1)U180JYSD(2)A(3) 18 pF

C90(1)U200JYSD(2)A(3) 20 pF

C90(1)U220JYSD(2)A(3) 22 pF

C90(1)U240JYSD(2)A(3) 24 pF

C90(1)U270JYSD(2)A(3) 27 pF

C90(1)U300JYSD(2)A(3) 30 pF

C90(1)U330JYSD(2)A(3) 33 pF

C90(1)U360JYSD(2)A(3) 36 pF

C90(1)U390JYSD(2)A(3) 39 pF

C90(1)U470JYSD(2)A(3) 47 pF

C90(1)U500JYSD(2)A(3) 50 pF

C90(1)U510JYSD(2)A(3) 51 pF

C91(1)U560JYSD(2)A(3) 56 pF

8.0

C91(1)U620JYSD(2)A(3) 62 pF

C91(1)U680JYSD(2)A(3) 68 pF

C91(1)U750JYSD(2)A(3) 75 pF

C92(1)U820JYSD(2)A(3) 82 pF 9.0

C93(1)U101JYSD(2)A(3) 100 pF 10.0

Y5P

C90(1)U101KYYD(2)A(3) 100 pF

±10%

7.0

5.0 0.55 ±0.1

5 mm,

7.5 mm,

10 mm

C90(1)U151KYYD(2)A(3) 150 pF

C90(1)U221KYYD(2)A(3) 220 pF

C90(1)U331KYYD(2)A(3) 330 pF

C90(1)U471KYYD(2)A(3) 470 pF

C91(1)U561KYYD(2)A(3) 560 pF 8.0

C91(1)U681KYYD(2)A(3) 680 pF

C92(1)U821KYYD(2)A(3) 820 pF 9.0

C92(1)U102KYYD(2)A(3) 1,000 pF

Y5U

C90(1)U102MYWD(2)A(3) 1,000 pF

±20%

7.0

5.0 0.55 ±0.1

5 mm, 7.5 mm, or 10 mmC92(1)U152MYWD(2)A(3) 1,500 pF 9.0

C92(1)U222MYWD(2)A(3) 2,200 pF

C94(1)U332MYWD(2)A(3) 3,300 pF 11.0 7.5 mm or 10

7.5 mm

or 10 mm

C96(1)U392MYWD(2)A(3) 3,900 pF 13.0 10 mm only

C96(1)U472MYWD(2)A(3) 4,700 pF

Y5V

C90(1)U102MYVD(2)A(3) 1,000 pF

±20%

7.0

5.0 0.55 ±0.1

5 mm, 7.5 mm, or 10 mm

C90(1)U152MYVD(2)A(3) 1,500 pF

C90(1)U222MYVD(2)A(3) 2,200 pF

C92(1)U332MYVD(2)A(3) 3,300 pF 9.0

C94(1)U392MYVD(2)A(3) 3,900 pF 11.0 7.5 mm or 10

7.5 mm

or 10 mm

C94(1)U472MYVD(2)A(3) 4,700 pF

C96(1)U682MYVD(2)A(3) 6,800 pF 13.0 10 mm only

C98(1)U103MYVD(2)A(3) 10,000 pF 15.0

KEMET Part Number Capacitance

Capacitance Tolerance

Body Diameter

(Maximum)

Body Thickness

(Maximum)

Lead Diameter Lead Spacing

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Item Specication Test Method

Operating Temperature Range −40ºC to +125ºC

Dielectric

Strength

Between lead

wires No failures

The capacitor shall not be damaged when voltage is applied

between the lead wires for 60 seconds.

2,000 VAC(rms) – 5.0 mm lead spacing

2,600 VAC(rms) – 7.5 mm and 10 mm lead spacing

Body Insulation No failures

The terminals (leads) of the capacitor

shall be connected together. A metal foil

is tightly wrapped around the body of the

capacitor at a distance of about 3 to 4 mm

from each terminal. The capacitor is then

inserted into a container lled with metal

balls approximately 1 mm in diameter. 2,600

VAC(rms) is applied for 60 seconds between

the capacitor lead wires and metal balls.

Metal

Foil

Metal

Balls

about

3 to 4 mm

Insulation Resistance (IR) 10,000 MΩ minimum

The insulation resistance shall be measured with 500±50 VDC

applied after 60±5 seconds of charging.

Capacitance Within specied tolerance

Y5P, Y5U and Y5V: Capacitance is measured at 1 kHz ±20% and 5

Vrms or less. (20±2°C)

SL: Capacitance is measured at 1 MHz ±20% and 1.0±0.2 Vrms

(25°C)

Dissipation Factor (DF) or Q

Temperature

Characteristics Specication

Y5P, Y5U DF ≤ 2.5%

Y5V DF ≤ 5.0%

≥ 30 pF: Q ≥ 1000

< 30 pF: Q ≥ 400

+(20 x C)

C = Nominal

capacitance

Temperature Characteristics

Temperature

Characteristics

Capacitance

Change

Y5P Within ±10%

Y5U Within +20%/−55%

Y5V Within ~+30%/−80%

SL −1,000 ~+350 ppmºC

(+20ºC ~+85ºC)

A capacitance measurement is made at each step specied:

Step Temperature

1+20±2ºC

2−25±2ºC

3+20±2ºC

4+85±2ºC

5+20±2ºC

Pre-treatment:

Capacitor is stored at 85±2ºC for 1 hour and then placed at room

condition

for 24±2 hours before measurement.

Terminal

Strength

Tensile Lead wire or capacitor body shall not

break.

With the termination in its normal position, the specimen is held

by its body in such a manner that the axis of the termination is

vertical; a tensile force of 10 N is applied to the termination in the

direction of its axis and acting in a direction away from the body

of the specimen.

Bending Lead wire or capacitor body shall not

break.

With the termination in its normal position, the specimen is held

by its body in such a manner that the axis of the termination is

vertical; a mass force of 5 N is then suspended from the end of

the termination. The body of the specimen is then inclined within

a period of 2 to 3 seconds, through an angle of approximately 90°

in the vertical plane and then resumed to its initial position over

the same period of time; this operation constitutes one bend.

One bend immediately followed by a second bend in the opposite

direction.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item Specication Test Method

Solderability

Lead wire should have a uniform coating

of solder in the axial direction and over

3/4 of its circumference.

The lead wire of the capacitor is dipped into molten solder for

5±0.5 seconds. The depth of immersion is up to 1.5 mm

(+5/−0 mm) from the root of lead wires.

Solder Temperature: Lead free solder (Sn-3Ag – 0.5Cu)

245°C ±5°C.

Soldering Effect

(Non-Preheat)

Appearance No visual defect

As shown in the gure below, the lead wires are immersed in

molten solder up to 1.5 mm (+5/−0 mm) from the end of the

epoxy meniscus (root of lead wire).

Duration/Solder Temperature: 3.5±0.5 seconds/350°C ±10°C or

10±1 seconds/260°C ±5°C

Molten

Solder

1.5 to

2.0 mm

Capacitor

Thermal

Screen

Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and

then placed at room condition1 for 24±2 hours before initial

measurements.

Post-treatment: Capacitor is stored for 1 to 2 hours at room

condition

IR 1,000 MΩ

Dielectric

Strength

Per item 1

Capacitance

Y5P, Y5U and Y5V: Within ±10%

SL: Within ±2.5% or ±0.25 pF, whichever

is larger.

Soldering Effect

(Preheat)

Appearance No visual defect

Capacitor is stored at 120°C +0/−5°C for 60 +0/−5 seconds.

Then, as shown in the gure below, the lead wires are immersed

in molten solder up to 1.5 mm (+5/−0mm) from the end of the

epoxy meniscus (root of lead wire).

Duration/Solder Temperature: 7.5 +0/−1 seconds/260°C ±5°C

Molten

Solder

1.5 to

2.0 mm

Capacitor

Thermal

Screen

Pre-treatment: Capacitor is stored at 85°C ±2°C for 1 hour and

then placed at room condition1 for 24±2 hours before initial

measurements.

Post-treatment: Capacitor is stored for 1 to 2 hours at room

condition

IR 1,000 MΩ

Dielectric

Strength

Per item 1

Capacitance

Y5P, Y5U and Y5V: Within ±10%

SL: Within ±2.5% or ±0.25 pF, whichever

is larger.

Biased Humidity

Appearance No visual defect Steady State Humidity: Load Humidity:

Capacitance

Temperature

Characteristics

Capacitance

Change

Y5P Within ±10%

Y5U Within ±20%

Y5V Within ±30%

Within ±2.5% or

±0.25 pF, whichever

is larger.

90 to 95% humidity at 40°C

±2°C for 500 ±12 hours.

Post Treatment:

Capacitor is stored for 1 to 2

hours at room condition1.

90 to 95% humidity at 40°C

±2°C for 500 ±12 hours with

full rated voltage applied.

Post Treatment:

Capacitor is stored for 1 to 2

hours at room condition1.

Y5P and Y5U: 5.0% maximum

Y5V: 7.5% maximum

SL: Less than 30 pF:

Q ≥ 100 + 10 × C/3

More than 30 pF: Q ≥ 200

C = Nominal capacitance

Y5P, Y5V and Y5U: 3,000 MΩ minimum

SL: 1,000 MΩ minimum

Dielectric

Strength

No failures

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item Specication Test Method

High

Temperature

Life

Appearance No visual defect

Impulse Voltage: Each individual capacitor is subjected to three 5

kv impulses prior to life testing.

0.9Vp

0.5Vp

Voltage

Time

(uS)

1.2

1.5

(uF)

0.01

0.1

Capacitors are placed in a circulating air oven for a period of

1,000 hours. The air in the oven is maintained at a temperature of

125°C ±2 throughout the test. The capacitors are subjected to AC

425 Vrms. Each hour the voltage is increased to AC 1,000 Vrms

for 0.1 seconds.

Capacitance

Change

Y5P, Y5V and Y5U: Within ±20%

SL: Within ±3 or ±0.3 pF,

whichever is larger.

3,000 MΩ minimum

SL: 1,000 MΩ minimum

Dielectric

Strength No failures

Flame Test

The capacitor ame extinguishes as

follows:

Cycle Time

1 ~ 4 30 seconds

maximum

560 seconds

maximum

The capacitor is exposed to a ame for 15 seconds and then

removed for 15 seconds. This test is repeated for 5 cycles.

Capacitor

Flame

38 127

20º

Gas Burner

(Unit:mm)

Active Flammability The cheesecloth should not ignite.

The capacitors are individually wrapped in at least one, but not

more than two, complete layers of cheesecloth. They are then

subjected to 20 discharges. The interval between successive

discharges is 5 seconds. The VAC is maintained for 2 minutes

after the last discharge.

Tr Vac

L3L4

C2C3CXCtVt

F R

Oscilloscope

1, 2

1 μF ±10% C

0.033 μF ±5% 10 kV

1-4

1.5 Mh ±20% 16A Rod core choke Cx Test capacitor

R100 ±2% V

VR ±5%

Ct 3 μF ±5% 10 kV V

Rated Voltage

F Fuse, Rated 10A Vt Voltage applied to Ct

5kV

time

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Table 2 – Performance & Reliability: Test Methods and Conditions cont'd

Item Specication Test Method

Passive Flammability

The burning time should not exceed 30

seconds.

The tissue paper should not ignite.

The capacitor under test is held into a ame and in a position

which best promotes burning. Each specimen is exposed to the

ame one time.

200

±5mm

About 8mm

45º

Test Specimen

About 10mm

Thick Board

Tissue

Time of exposure to ame:

Length of ame:

Gas burner length:

Inside diameter:

Outside diameter:

Gas butane gas purity:

30 seconds

12±1 mm

35 mm minimum

0.5±0.1 mm

0.9 mm maximum

95% minimum

Temperature

Cycle

Appearance No visual defect

The capacitor is subjected to 5 temperature cycles.

Temperature Cycle

Step Temperature (°C)

Dwell

Time

(minutes)

Transition

Time

(minutes)

1−40 +0/−3 30

2Room temperature 3

3125 +3/−0 30

4Room temperature 3

Pre-treatment: Capacitor shall be stored at 85±2 for 1 hour then

placed at room condition1 for 24±2 hours.

Post-treatment: Capacitor is stored for 1 to 2 hours at room

condition1.

Capacitance

Temperature

Characteristics

Capacitance

Change

SL Within ±5%

Y5P Within ±10%

Y5U, Y5V Within ±20%

DF/Q

SL ≥ 30 pF: Q ≥ 350

< 30 pF: Q ≥ 275

+5/2C

C = Nominal

capacitance

Y5P DF ≤ 5%

Y5U, Y5V DF ≤ 7.5%

IR 3,000 MΩ minimum

Dielectric

Strength No failures

1 “Room Condition” is dened as follows: Temperature: 15 ~ 35°C/Humidity: 45 ~ 75%/Atmospheric Pressure: 86 ~ 106 kPa.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Soldering and Mounting Information

Soldering:

When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specication of the capacitor.

Subjecting this product to excessive heating could reow the solder joint between the lead and ceramic element and/or may

result in thermal shocks that can crack the ceramic element.

When soldering these capacitors with a soldering iron, it should be performed under the following conditions:

• Temperature of iron-tip: 400ºC maximum

• Soldering iron wattage: 50 W maximum

• Soldering time: 3.5 seconds maximum

Cleaning (ultrasonic cleaning):

To perform ultrasonic cleaning, observe the following conditions:

• Rinse bath capacity: Output of 20 watts per liter or less

• Rinsing time: 5 minute maximum

• Do not vibrate the PCB/PWB directly

• Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires

Construction

Detailed Cross Section

Epoxy Encapsulation

(0.4 mm Minimum Thickness,

Pigment = Blue/UL 94 V-0)

Lead Attach Solder

(Sn96.5/Ag3/Cu0.5)

Electrode

(Ag – Glass Frit)

Core Metal

Barrier Layer

Finish Layer

Steel

100% Sn

(3-7 µm)

Lead Wire

Dielectric

Material (BaTiO3)

Lead Attach Solder

(Sn96.5/Ag3/Cu0.5)

Electrode

(Ag – Glass Frit)

Dielectric

Material

(BaTiO3)

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Marking

These capacitors shall be stamped or laser marked with KEMET's trademark, type designation, capacitor class, rated voltage,

rated capacitance and capacitance tolerance codes. In addition, all devices are marked with the recognized approval mark

and a date/lot code for traceability. Marking will be supplied either on one side or both sides of the encapsulated capacitor

body. All marking shall be legible to allow for clear identication of the component. Marking appears in legible contrast.

Illustrated below is an example of the marking format and content. (Two sided marking is limited to capacitors with body

diameters ≤ 8.0 mm.)

Single Sided

UL approval mark

VDE & ENEC

approval marks

IEC 60384-14 3rd

(2005)

Rated Capacitance

(3 Numeric Characters)

Capacitance Tolerance Code

(1 Character)

Capacitor Class

and Rated Voltage

KEMET ID

Type Designation

(2 Characters)

Date/Lot Code

(See Table Below)

Double Sided

Capacitor Class

and Rated Voltage

Front Back

KEMET ID

Type Designation

(2 Characters) VDE & ENEC

approval marks

IEC 60384-14 3rd

(2005)

UL approval mark

Date/Lot Code

(See Table Below)

Rated Capacitance

(3 Numeric Characters)

Capacitance

Tolerance Code

(1 Character)

Date/Lot Code Explanation

6 C 6 1234

Last digit of year,

e.g.,

6 = 2016

Manufacturing

Location Code

Manufacturing

Month:

1-9 = Jan - Sept

A = October

N = November

D = December

Last 4 digits of

lot no.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Packaging Quantities

Capacitor

Body Diameter

(mm)

Body Diameter

Code1

Bulk Bag

(Loose)

Ammo Pack (Carrier Tape)

Component pitch on carrier tape2

12.7 mm 15 mm 25.4 mm

7.0

500 pieces/bag 1,000 pieces/box

1,000 pieces/box

8.0 1

9.0 2

10.0 3

11.0 4

12.0

13.0 6

500 pieces/box14.0 7

15.0

1 The "Body Diameter Code" is located in the third character position of the ordering code. This code identies the maximum diameter of the capacitor

body in millimeters. For more information regarding the ordering code, see "Ordering Information" section of this document.

2 For details regarding component pitch on carrier tape, see "Ammo Pack Taping Format" and "Ammo Pack Taping Specications" sections of this

document.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Figure 1 - Ammo Pack Taping Format

5 mm and 7.5 mm Lead Spacing:

P2P

H0W1

ØD0

Ød

∆S

ℓ

10 mm Lead Spacing:

P2P

H0W1

ØD0

Ød

∆S

ℓ

Table 3 – Ammo Pack Taping Specications

1 Prefromed (crimped) lead congurations include vertical kink, outside kink and inside kink. See "Lead Congurations" and "Ordering Information"

sections of this document for further details.

2 Also referred to as "lead length" in this document.

Lead Spacing 5 mm 7.5 mm 10 mm

Lead Style Straight Preformed1Straight Preformed1Straight Preformed1

Item Symbol Dimensions (mm)

Lead Spacing F5.0+0.8/−0.2 7.5±1.0 10.0±1.0

Component Pitch P12.7 15.0 25.4±2

Sprocket Hole Pitch P

12.7±0.3 15.0±0.3 12.7±0.3

Sprocket Hole Center to

Component Center P26.35±1.5 7.5±1.5 12.7±1.5

Sprocket Hole Center to Lead

Center P13.75±1.0 3.75±1.0 7.7±1.5

Body Diameter D See "Product Ordering Codes and Ratings" section of this document.

Component Alignment (side/side) ∆S 0±2.0

Carrier Tape Width W18.0+1.0/−0.5

Sprocket Hole Position W

9.0±0.5

T maximum

Marking Side

∆h1∆h2

t2t1

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Table 3 – Ammo Pack Taping Specications cont'd

1 Prefromed (crimped) lead congurations include vertical kink, outside kink and inside kink. See "Lead Congurations" and "Ordering Information"

sections of this document for further details.

2 Also referred to as "lead length" in this document.

Application Notes:

Storage and Operating Conditions:

The insulating coating of these devices does not form an air and moisture-tight seal. Avoid exposure to moisture and do not

use or store these devices in a corrosive atmosphere, especially where chloride gas, sulde gas, acid, alkali, salt, or the like

are present. Before cleaning, bonding or molding these devices, it is important to verify that your process does not affect

product quality and performance. KEMET recommends testing and evaluating the performance of a cleaned, bonded or

molded product prior to implementing and/or qualifying any of these processes. Store the capacitors where the temperature

and relative humidity do not exceed 40 degrees Centigrade and 70% respectively. For optimum solderability, capacitor stock

should be used promptly, preferably within 6 months of receipt.

Working Voltage:

Application voltage (Vp-p or Vo-p) must not exceed the voltage rating of the capacitor. Irregular voltages can be generated

for a transient period of time when voltage is initially applied and/or removed from a circuit. It is important to choose a

capacitor with a voltage rating greater than or equal to these irregular voltages.

Lead Spacing 5 mm 7.5 mm 10 mm

Lead Style Straight Preformed1Straight Preformed1Straight Preformed1

Item Symbol Dimensions (mm)

Height to Seating Plane2

(preformed leads1)H0N/A 18.0 +2.0/-0 N/A 18.0 +2.0/-0 N/A 18.0 +2.0/-0

Height to Seating Plane2

(straight leads) H20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A 20.0 +1.5/-1.0 N/A

Lead Protrusion ℓ2.0 maximum

Diameter of Sprocket Hole D

4.0 ±0.2

Lead Diameter φd 0.55 ±0.1

Carrier Tape Thickness t

0.6 ±0.3

Total Thickness (Carrier Tape,

Hold-Down Tape and Lead) t21.5 maximum

Component Alignment (front/

back )

∆h1

2.0 maximum

∆h2

Cut Out Length L 11.0 maximum

Hold-Down Tape Width W

11.0 minimum 11.5 minimum

Hold-Down Tape Position W

3.0 maximum 1.5 ±1.5

Coating Extension on Leads

(meniscus) e3.0 maximum for straight lead; not to exceed the bend for preformed1 lead congurations.

Body Thickness TSee "Product Ordering Codes and Ratings" section of this document.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

Operating Temperature and Self-Generating Heat:

The surface temperature of a capacitor should be kept below the upper limit of its rated operating temperature range. Be

sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current,

pulse current or similar current, it may self-generate heat due to dielectric loss. Temperature rise due to self-generated

heating should not exceed 20°C (while operated at an atmosphere temperature of 25°C).

Handling - Vibration and Impact:

Do not expose these devices or their leads to excessive shock or vibration during use.

FAILURE TO FOLLOW THE ABOVE CAUTIONS MAY RESULT, WORST CASE, IN A SHORT CIRCUIT AND CAUSE FUMING OR

PARTIAL DISPERSION WHEN THE PRODUCT IS USED.

Radial Leaded Ceramic Disc Capacitors

Safety Standard Recognized, 900 Series, Encapsulated, AC Type, X1 400 VAC/Y2 250 VAC (Industrial Grade)

KEMET Electronic Corporation Sales Of ces

For a complete list of our global sales of ces, please visit www.kemet.com/sales.

Disclaimer

All product speci cations, statements, information and data (collectively, the “Information”) in this datasheet are subject to change. The customer is responsible for

checking and verifying the extent to which the Information contained in this publication is applicable to an order at the time the order is placed.

All Information given herein is believed to be accurate and reliable, but it is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.

Statements of suitability for certain applications are based on KEMET Electronics Corporation’s (“KEMET”) knowledge of typical operating conditions for such

applications, but are not intended to constitute – and KEMET speci cally disclaims – any warranty concerning suitability for a speci c customer application or use.

The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any

technical advice inferred from this Information or otherwise provided by KEMET with reference to the use of KEMET’s products is given gratis, and KEMET assumes no

obligation or liability for the advice given or results obtained.

Although KEMET designs and manufactures its products to the most stringent quality and safety standards, given the current state of the art, isolated component

failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards

(such as installation of protective circuitry or redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or

property damage.

Although all product–related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicted or that other

measures may not be required.

KEMET is a registered trademark of KEMET Electronics Corporation.