Comfort Outdoor ___________________ Preface 1 ___________________ Overview SIMATIC HMI HMI devices TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions 2 ___________________ Safety instructions Mounting and connecting the 3 ___________________ HMI device 4 ___________________ Configuring the device ___________________ 5 Commissioning a project ___________________ 6 Maintenance and care ___________________ 7 Technical information ___________________ A Technical Support 05/2016 A5E35956909-AC Legal information Warning notice system This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION indicates that minor personal injury can result if proper precautions are not taken. NOTICE indicates that property damage can result if proper precautions are not taken. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The product/system described in this documentation may be operated only by personnel qualified for the specific task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified personnel are those who, based on their training and experience, are capable of identifying risks and avoiding potential hazards when working with these products/systems. Proper use of Siemens products Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. The permissible ambient conditions must be complied with. The information in the relevant documentation must be observed. Trademarks All names identified by (R) are registered trademarks of Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Division Digital Factory Postfach 48 48 90026 NURNBERG GERMANY A5E35956909-AC 05/2016 Subject to change Copyright (c) Siemens AG 2016. All rights reserved Preface Scope These compact operating instructions apply to the following HMI devices in conjunction with the WinCC software package: TP700 Comfort Outdoor, article number 6AV2124-0GC13-0AX_ TP1500 Comfort Outdoor, article number 6AV2124-0QC13-0AX_ "_" stands for the variant key of the article number. These compact operating instructions describe the technical differences of the Outdoor devices to the corresponding standard devices. The information in these compact operating instructions take precedence in terms of their binding character over the statements in the following underlying operating instructions, the release notes and the online help. Operating instructions on the Comfort Panels (http://support.automation.siemens.com/WW/view/en/49313233) Note This document belongs to the device and will also be required for repeat commissioning. Keep all supplied and supplementary documentation for the entire service life of the device. Provide all associated documents to any future owner of the device. Style conventions Style Convention Scope "Add screen" * Terminology that appears in the user interface, for example, dialog names, tabs, buttons, menu commands * Required input, for example, limits, tag values. * Path information "File > Edit" Operational sequences, for example, menu commands, shortcut menu commands. <F1>, <Alt+P> Keyboard operation Please observe notes labeled as follows: Note A note contains important information about the product described in the manual and its use, or a specific section of the manual to which you should pay particular attention. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 3 Preface Naming conventions Term Applies to System * System * Machining center * One or more machines HMI device * TP700 Comfort Outdoor Device * TP1500 Comfort Outdoor WinCC WinCC V13 SP1 (TIA Portal) Figures This document contains figures of the devices described. The figures can deviate from the particularities of the delivered device. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 4 Compact Operating Instructions, 05/2016, A5E35956909-AC Table of contents Preface ................................................................................................................................................... 3 1 2 3 4 5 6 Overview................................................................................................................................................. 7 1.1 Product description ................................................................................................................... 7 1.2 Software requirements .............................................................................................................. 8 1.3 Scope of delivery ...................................................................................................................... 9 1.4 1.4.1 1.4.2 Configuration of the devices ...................................................................................................10 Device views ...........................................................................................................................10 Interfaces ................................................................................................................................11 Safety instructions ................................................................................................................................. 12 2.1 General safety instructions .....................................................................................................12 2.2 Notes about usage ..................................................................................................................13 Mounting and connecting the HMI device .............................................................................................. 14 3.1 3.1.1 3.1.2 3.1.3 3.1.4 3.1.5 Preparing for installation .........................................................................................................14 Checking the package contents ..............................................................................................14 Checking the operating conditions ..........................................................................................15 Selecting a mounting position .................................................................................................15 Checking clearances...............................................................................................................17 Preparing the mounting cutout ................................................................................................17 3.2 Mounting the device ................................................................................................................19 3.3 Connecting the device ............................................................................................................20 Configuring the device .......................................................................................................................... 21 4.1 Overview .................................................................................................................................21 4.2 Changing the brightness settings ...........................................................................................21 Commissioning a project ....................................................................................................................... 23 5.1 Overview .................................................................................................................................23 5.2 Using existing projects ............................................................................................................23 Maintenance and care........................................................................................................................... 24 6.1 Cleaning the device ................................................................................................................24 6.2 Repair, spare parts, recycling and disposal ............................................................................24 TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 5 Table of contents 7 A Technical information ............................................................................................................................ 25 7.1 Certificates and approvals ..................................................................................................... 25 7.2 7.2.1 7.2.2 Electromagnetic compatibility ................................................................................................ 25 Emitted interference ............................................................................................................... 25 Immunity to interferences ....................................................................................................... 25 7.3 7.3.1 7.3.2 Mechanical ambient conditions .............................................................................................. 26 Storage conditions ................................................................................................................. 26 Operating Conditions ............................................................................................................. 26 7.4 7.4.1 7.4.2 7.4.3 Climatic ambient conditions ................................................................................................... 26 Long-term storage .................................................................................................................. 26 Transport and short-term storage .......................................................................................... 27 Operating Conditions ............................................................................................................. 27 7.5 Information on insulation tests, protection class and degree of protection ............................ 28 7.6 7.6.1 7.6.2 Dimension drawings ............................................................................................................... 29 Dimension drawings of the TP700 Comfort Outdoor ............................................................. 29 Dimension drawings of the TP1500 Comfort Outdoor ........................................................... 30 7.7 Specifications ......................................................................................................................... 31 7.8 Description of the ports .......................................................................................................... 32 7.9 Scope of functions with WinCC.............................................................................................. 33 Technical Support ................................................................................................................................. 36 A.1 Service and support ............................................................................................................... 36 A.2 Troubleshooting and system alarms ...................................................................................... 36 Index .................................................................................................................................................... 37 TP700 Comfort Outdoor, TP1500 Comfort Outdoor 6 Compact Operating Instructions, 05/2016, A5E35956909-AC 1 Overview 1.1 Product description SIMATIC Comfort Outdoor devices with glass touch screen and powder-coated, UV-resistant aluminum front are designed for use in indoor and outdoor areas, for example, in the fields of Oil&Gas, Marine or Refrigeration Technology. All devices offer the same excellent functionality and are configured exclusively with the innovative HMI software, WinCC. The engineering software is integrated in the engineering framework, "Totally Integrated Automation Portal". TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 7 Overview 1.2 Software requirements Features Front Display Touch screen Interfaces * External dimensions of the front and mounting cutout correspond to the standard product * Durable powder coating * High UV resistance * GFG (Glass-Film-Glass) touch screens, analog resistive * Manual or automatic brightness control with brightness sensor * High-resolution TFT display in widescreen format with 16 million colors * Suitable for use in daylight * Anti-reflective and bonded for glare-free reading * Resistive single touch screen * Suitable for operation with gloves, pen and fingers * 2 PROFINET interfaces * 1 PROFIBUS interface * USB 2.0 ports: - 2 x USB host interface (type A) - 1 x USB device interface (type mini B) Mechanical differences to the standard product Device depth The Comfort Outdoor devices are deeper than the corresponding Comfort HMI device. Read the information in the following sections: Slots for SD memory cards 1.2 * Preparing the mounting cutout (Page 17) * Dimension drawings (Page 29) The protection mechanism of the SD memory card for the Comfort Outdoor devices is mechanically differently than that of the corresponding Comfort HMI device. The safety tab is not required with the Comfort Outdoor devices. Software requirements You require the software WinCC V13 SP1 (TIA Portal) Update 6 with the Hardware Support Package "HSP0149 HMI TP700_1500 Comfort Outdoor" or later versions. You can find the software under Technical Support on the Internet. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 8 Compact Operating Instructions, 05/2016, A5E35956909-AC Overview 1.3 Scope of delivery 1.3 Scope of delivery The following components are included in the scope of delivery of the HMI device. Name Figure Quantity HMI device 1 Installation instructions 1 (Quick Install Guide) Mounting clips Aluminum mounting clip 8 TP700 Comfort Outdoor Steel mounting clip 12 TP1500 Comfort Outdoor TP700 Comfort Outdoor Strain relief Example: Strain relief 1 Power supply terminal Connector, female, 2-pin, type 1 1 Some components in the scope of delivery are also available as accessories, see "Accessories" section in the Comfort Panels operating instructions or directly in the Industry Mall (https://mall.industry.siemens.com). TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 9 Overview 1.4 Configuration of the devices 1.4 Configuration of the devices 1.4.1 Device views This section describes the basic design of the device using the example of the TP700 Comfort Outdoor. Front view and side view Light sensor Aluminum front, powder coated Glass touch screen / display Cutouts for attaching the mounting clamps Rating plate Slot for data memory card Slot for system memory card Interface inscription Rear view TP700 Comfort Outdoor, TP1500 Comfort Outdoor 10 Compact Operating Instructions, 05/2016, A5E35956909-AC Overview 1.4 Configuration of the devices 1.4.2 Interfaces Position of the interfaces The figure below shows the interfaces of the HMI devices. X80 power supply connector Connection for equipotential bonding (ground) X2 PROFIBUS (Sub-D RS422/485) X61 / X62 USB type A X1 PROFINET (LAN), 10/100 Mb X90 Audio Line IN / OUT X60 USB type Mini B Additional information Use the X1 or X60 interface to connect a configuration PC. Use the X61 / X62 interfaces to connect peripheral devices such as a printer or keyboard. Use the X90 interface to connect a loudspeaker. You can fasten the USB and PROFINET connecting cables to the rear panel of the HMI device with cable ties. Secure the cables with a separate strain relief for the TP700 Comfort Outdoor. Install the strain relief on the HMI device. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 11 2 Safety instructions 2.1 General safety instructions The general safety instructions in the "Comfort Panel" operating instructions apply. Also note the following for Comfort outdoor devices: WARNING Unintended functions may be triggered with icing If the operating temperature is below 2 C, icing may occur on the front of the device. Icing may trigger unintended functions in some circumstances. To avoid triggering unintended functions, you can take the following measures, for example: * Install an additional enabling switch in your plant for operator actions that initiate a dangerous operating state. * Assign a password to operator actions or inputs that initiate a dangerous operating state. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 12 Compact Operating Instructions, 05/2016, A5E35956909-AC Safety instructions 2.2 Notes about usage 2.2 Notes about usage Industrial applications The HMI device is designed for outdoor areas in industrial applications. It conforms to the following standards: Requirements of the emission standard for industrial environments, EN 61000-6-4: 2007 + A1:2011 ESD immunity requirements to DIN EN 61000-6-2:2005 Use in residential areas Note The HMI device is not intended for use in residential areas. Operation of an HMI device in residential areas can have a negative influence on radio/TV reception. If the HMI device is used in a residential area, you must take measures to achieve Limit Class B conforming to EN 55011 for RF interference. Individual acceptance is required. Use with additional measures The HMI device should not be used at the following locations unless additional measures are taken: In locations with a high degree of ionizing radiation In locations with severe operating conditions, for example, due to: - Corrosive vapors, gases, oils or chemicals - Electrical or magnetic fields of high intensity In systems that require special monitoring, for example, in: - Elevators - Systems in especially hazardous rooms TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 13 Mounting and connecting the HMI device 3.1 Preparing for installation 3.1.1 Checking the package contents 3 Check the package content for visible signs of transport damage and for completeness. Note Damaged parts A damaged part will cause the HMI device to malfunction. Do not install parts damaged during shipment. In the case of damaged parts, contact your Siemens representative. Check the scope of supply of the HMI device (see Scope of delivery (Page 9)). Additional documents may be included in the delivery. The documentation is part of the HMI device and is required for subsequent commissioning. Keep all enclosed documentation for the entire service life of the HMI device. You must pass along the enclosed documentation to any subsequent owner or user of the HMI device. Make sure that every supplement to the documentation that you receive is stored together with the operating instructions. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 14 Compact Operating Instructions, 05/2016, A5E35956909-AC Mounting and connecting the HMI device 3.1 Preparing for installation 3.1.2 Checking the operating conditions Note the following aspects before installing the HMI device: 1. Familiarize yourself with the technical specifications for operating the HMI device. You can find this information in the section "Technical information (Page 25)". 2. Read the information about local use of the HMI device, see section "Notes about usage (Page 13)". 3.1.3 Selecting a mounting position The device is suitable for installation in: Mounting cabinets Control cabinets Switchboards Consoles In the following, all of these mounting options are referred to by the general term "cabinet". The device is self-ventilated and approved for inclined mounting at angles up to +/-35 from the vertical in stationary cabinets. NOTICE Damage due to overheating Inclined installation reduces the convection by the device and therefore the maximum permitted ambient temperature for operation. If there is sufficient forced ventilation, the device can also be operated in the inclined mounting position up to the maximum permitted ambient temperature for vertical installation. The device may otherwise be damaged and its certifications and warranty will be rendered null and void. The ambient temperature ranges listed in this section apply to the temperature inside the cabinet. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 15 Mounting and connecting the HMI device 3.1 Preparing for installation Mounting position Select one of the approved mounting positions for your device. The approved mounting positions are described in the following sections. Mounting in horizontal format Ambient temperature when mounted in horizontal format: Vertical mounting (0 inclined): Maximum +60 C Inclined mounting (inclined up to 35): Maximum +50 C Mounting in vertical format Ambient temperature when mounted in vertical format: Vertical mounting (0 inclined): Maximum +50 C Inclined mounting (inclined up to 35): Maximum +45 C See also Operating Conditions (Page 27) TP700 Comfort Outdoor, TP1500 Comfort Outdoor 16 Compact Operating Instructions, 05/2016, A5E35956909-AC Mounting and connecting the HMI device 3.1 Preparing for installation 3.1.4 Checking clearances The following clearances are required around the HMI device to ensure sufficient selfventilation: At least 15 mm to both the right and left of the mounting cutout (in x direction) to allow for insertion of the mounting clips during installation At least 50 mm above and 50 mm below the mounting cutout (in the y direction) for ventilation At least 10 mm behind the rear panel of the HMI device (in the z direction) The following figure shows the clearances during mounting of the HMI devices in horizontal and vertical formats: Note Ensure that the maximum ambient temperature is not exceeded when mounting the device in a cabinet and especially in a closed enclosure. 3.1.5 Preparing the mounting cutout Note Stability of the mounting cutout The material in the area of the mounting cutout must provide sufficient strength to guarantee lasting and safe mounting of the HMI device. To achieve the degrees of protection described below, it must be ensured that deformation of the material cannot occur due to the force of the mounting clips or operation of the device. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 17 Mounting and connecting the HMI device 3.1 Preparing for installation Degrees of protection The degrees of protection of the HMI device can only be guaranteed if the following requirements are met: Material thickness at the mounting cutout for a protection rating of IP66 or Front face only Type 4X/Type 12 (Indoor/Outdoor): 2 mm to 6 mm Permitted deviation from plane at the mounting cutout: 0.5 mm This condition must be met for the mounted HMI device. Permitted surface roughness in the area of the mounting seal: 120 m (Rz 120) Compatibility of the mounting cutout to other HMI devices The mounting cutouts of the following HMI devices are compatible with the mounting cutouts of the following predecessor devices: HMI device Mounting cutout compatible with TP700 Comfort Outdoor TP700 Comfort, TP 177B 6", MP 177 6", TP 277 6" TP1500 Comfort Outdoor TP1500 Comfort Please note that although the dimensions for the mounting cutout are the same, the device depth and/or the enclosure front dimensions may differ from the respective dimensions of the predecessor devices. Dimensions of the mounting cutout Width and height should be reversed accordingly when mounting in vertical format. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 18 Compact Operating Instructions, 05/2016, A5E35956909-AC Mounting and connecting the HMI device 3.2 Mounting the device Mounting depth The mounting depth of the devices is: 3.2 HMI device Mounting depth TP700 Comfort Outdoor 67 mm TP1500 Comfort Outdoor 77 mm Mounting the device Positions of the mounting clips To achieve the degree of protection for the HMI device, the positions for the mounting clips shown below must be adhered to. The positions of the mounting clips are marked by stamps on the cutouts. Fit the mounting clips in all the stamped cutouts. The following table shows the type, number, and position of the mounting clips needed for the respective HMI devices. HMI device Mounting clips Type Number TP700 Comfort Outdoor Aluminum mounting clip 8 TP1500 Comfort Outdoor Steel mounting clip 12 Position on the HMI device Requirement All packaging components and protective films were removed from the HMI device. To install the HMI device, you need the mounting clips from the accessories kit. The mounting seal must be installed on the HMI device. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 19 Mounting and connecting the HMI device 3.3 Connecting the device Procedure Note Risk of guaranteed degree of protection not being met If the mounting seal is damaged, the degree of protection is not guaranteed. Replace the device in this case. Note Installation of the HMI device Always mount the HMI device according to the instructions in this manual. Mounting clips for TP700 Comfort Outdoor: Mounting clips for TP1500 Comfort Outdoor: Proceed as follows: 1. Insert the HMI device into the mounting cutout from the front. 2. Insert the mounting clamp into the cutout provided on the HMI device. 3. Tighten the mounting clamp with the setscrew. Note Adhere to the permitted torque when tightening the setscrew of the mounting clamp: 0.5 Nm 4. Repeat steps 2 and 3 for all mounting clips. 5. Check the fit of the device in the mounting cutout. 3.3 Connecting the device The specifications in "Comfort Panels" operating instructions apply. The X3 interface "PROFINET (LAN) 10/100/1000 Mbit" is not featured on the TP700 Comfort Outdoor and TP1500 Comfort Outdoor devices. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 20 Compact Operating Instructions, 05/2016, A5E35956909-AC Configuring the device 4.1 4 Overview The specifications in the "Comfort Panel" operating instructions apply for commissioning and parameter assignments. The enhanced brightness control of the Comfort Panels Outdoor differs from the other Comfort HMI devices and is described in the following section. 4.2 Changing the brightness settings The Comfort Outdoor Panels feature a manual or automatic brightness control with a brightness sensor. Make the appropriate settings in the Control Panel. Requirement The Control Panel is open. Set brightness Proceed as follows: 1. Open the "Display Properties" dialog with the Display icon. 2. Switch to the "Brightness" tab. The figure below shows the factory settings. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 21 Configuring the device 4.2 Changing the brightness settings Select the "Manual" or "Auto" option. - In the "Manual" mode, you can adjust the brightness to the desired value using the slider. Note "Manual" mode A change in the brightness value through the configuration takes precedence over the manual setting. - in the "Auto" mode, you can set the minimum and maximum brightness for the automatic brightness control of the HMI device under "Brightness Range". NOTICE "Auto" mode (factory state) The brightness parameters are controlled by the light sensor in "Auto" mode. The brightness can no longer be changed manually or through the configuration. The "Screen saver" function is available as usual. 3. If you want to check the settings without closing the dialog, press the "Apply" button. 4. To discard the settings and close the dialog, press the "Cancel". button. To save the settings and close the dialog, press the "OK" button. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 22 Compact Operating Instructions, 05/2016, A5E35956909-AC Commissioning a project 5.1 5 Overview The specifications in "Comfort Panels" operating instructions apply. 5.2 Using existing projects Proceed as follows to transfer an existing project to the HMI device: 1. Open the existing project in WinCC (TIA Portal). 2. Make sure that the project is dimensioned within the functional scope of the HMI device, see section "Scope of functions with WinCC (Page 33)". Note The functional scope of the TP1500 Comfort Outdoor corresponds to the functional scope of a TP1200 Comfort. 3. Replace the HMI device in WinCC. 4. Transfer the project to the HMI device as described in the "Comfort Panel" operating instructions. Note "Backup, Restore" and "Automatic Backup" only for devices with identical article numbers The "Backup" and "Restore" function using a data memory card and the "Automatic Backup" function using the system memory card are only available for devices with identical article numbers. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 23 6 Maintenance and care 6.1 Cleaning the device The specifications in "Comfort Panels" operating instructions apply. NOTICE Disable or switch off the device while cleaning Switch off the HMI device or activate the clean screen when you clean the appliance during operation. Note Cleaning of the coated glass touch screen Take care not to damage the glass touch screen and the coating of the touch screen on Comfort Outdoor devices. Use a cleaning cloth and dishwashing liquid or foaming screen cleaners. Apply as little pressure as possible on the touch screen when cleaning. 6.2 Repair, spare parts, recycling and disposal The specifications in "Comfort Panels" operating instructions apply. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 24 Compact Operating Instructions, 05/2016, A5E35956909-AC Technical information 7.1 7 Certificates and approvals Approvals The device is certified as shown on the rear of the device. As soon as additional certificates are available, you can find them in the Industry Mall or Technical Support. Search for your device and use the link "Support > Approvals / Certificates". 7.2 Electromagnetic compatibility The device is designed for industrial use. 7.2.1 Emitted interference The device meets the requirements according to EN 61000-6-4. The device corresponds to limit class A. Note The HMI device is not intended for use in residential areas. Operation of an HMI device in residential areas can have a negative influence on radio/TV reception. 7.2.2 Immunity to interferences The device meets the requirements according to EN 61000-6-2. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 25 Technical information 7.3 Mechanical ambient conditions 7.3 Mechanical ambient conditions 7.3.1 Storage conditions The following information is for a device that is transported and stored in its original packaging. The device meets the requirements according to IEC 60721-3-2 Class 2M2 with the following amendments and limitations: 7.3.2 Type of condition Permitted range Free fall 1m Vibration to IEC 60068-2-6 5 .. 8.4 Hz, deflection 3.5 mm 8.4 ... 500 Hz, acceleration 1 g Shock to IEC 60068-2-27 250 m/s2, 6 ms, 1000 shocks Operating Conditions The following information applies to a device installed according to the specifications in these operating instructions. The device meets the requirements according to IEC 60721 Class 3M3 with the following amendments and limitations: Type of condition Permitted range Vibration to IEC 60068-2-6 5 ... 8.4 Hz, deflection 3.5 mm 8.4 ... 200 Hz, acceleration 1 g Shock to IEC 60068-2-27 150 m/s2, 11 ms, 3 shocks 7.4 Climatic ambient conditions 7.4.1 Long-term storage The following information applies to a device that is stored in its original packaging for longer than two weeks. The device meets the requirements of IEC 60721-3-1 Class 1K2. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 26 Compact Operating Instructions, 05/2016, A5E35956909-AC Technical information 7.4 Climatic ambient conditions 7.4.2 Transport and short-term storage The following information applies to a device that is transported in the original packaging and weather-proof packaging, and stored from some time. The device meets the requirements according to IEC 60721-3-2 Class 2K4 with the following amendments and limitations: Type of condition Permitted range Temperature -30 ... 70 C Atmospheric pressure 1080 ... 660 hPa, corresponds to an elevation of -1000 to 3500 m Relative humidity 10 ... 90 % Pollutant concentration SO2: < 0.5 ppm; relative humidity < 60 %, no condensation H2S: < 0.1 ppm; relative humidity < 60 %, no condensation Note If dewing has developed, wait approximately 4 hours until the HMI device has dried completely before switching it on. Do not expose the HMI device to direct radiation from a heater. 7.4.3 Operating Conditions The following information applies to a device installed according to the specifications in these compact operating instructions. The HMI device is designed for stationary operation according to IEC 60721. The device meets the requirements according to IEC 60721-3-3 Class 3K3 with the following amendments and limitations: Permitted range Type of condition Mounting position Elevation -1000 ... 2000 m Elevation 3000 m * Temperature, Vertical -30 ... 60 C -30 ... 54 C Mounting in horizontal format Inclined, maximum inclination 35 -30 ... 50 C -30 ... 45 C Temperature, Vertical -30 ... 50 C -30 ... 45 C Mounting in vertical format Inclined, maximum inclination 35 -30 ... 45 C -30 ... 40 C Atmospheric pressure, operation elevation 1080 ... 795 hPa, corresponds to an elevation of -1000 to 2000 m Relative humidity From 10 to 90%, without condensation Pollutant concentration SO2: < 0.5 ppm; relative humidity < 60 %, no condensation 795 ... 701 hPa, corresponds to an elevation of 2000 ... 3000 m H2S: < 0.1 ppm; relative humidity < 60 %, no condensation * Interpolation of the maximum temperature value is permitted in the range of 2000 ... 3000 m. Note The system components connected to the HMI device, the power supply for example, must also be suited to the respective operating conditions. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 27 Technical information 7.5 Information on insulation tests, protection class and degree of protection 7.5 Information on insulation tests, protection class and degree of protection Insulation test The insulation strength is demonstrated in the type test with the following test voltages in accordance with IEC 61131-2: Circuits with rated voltage of Ui Test voltage Insulation tested with (type test) 707 V DC to other circuits / to ground Degree of pollution and overvoltage category The device meets the following requirements according to IEC 61131-2:2007: Degree of pollution 2 (front) 1 (rear) Overvoltage category II Protection class Protection class III according to IEC 61131-2 Protection against foreign objects and water The device meets the requirements according to EN 60529. Device side Degree of protection Front When mounted: Rear panel * IP66 * Type 4X/Type 12 (Indoor/Outdoor) IP20 Protection against contact with standard test probes. There is no protection against the ingress of water. The front protection rating can only be guaranteed if the mounting seal lies flush against the mounting cutout. Read the corresponding information in section "Preparing the mounting cutout (Page 17)". TP700 Comfort Outdoor, TP1500 Comfort Outdoor 28 Compact Operating Instructions, 05/2016, A5E35956909-AC Technical information 7.6 Dimension drawings 7.6 Dimension drawings 7.6.1 Dimension drawings of the TP700 Comfort Outdoor TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 29 Technical information 7.6 Dimension drawings 7.6.2 Dimension drawings of the TP1500 Comfort Outdoor TP700 Comfort Outdoor, TP1500 Comfort Outdoor 30 Compact Operating Instructions, 05/2016, A5E35956909-AC Technical information 7.7 Specifications 7.7 Specifications Weight TP700 Comfort Outdoor TP1500 Comfort Outdoor approx. 1.5 kg 4.0 kg Weight without packaging Display TP700 Comfort Outdoor Type Active display area Resolution 7.0'' 15.4'' 152 mm x 91 mm 331 x 207 mm 800 x 480 pixels 1280 x 800 pixels Possible colors Up to 16 million Brightness control Manual/automatic, value range 0 to 100 1, 0 = backlighting off Backlighting 1 2 TP1500 Comfort Outdoor LCD TFT LED Half Brightness Life Time (MTBF 2) 50000 h Pixel error class in accordance with ISO 9241-307 I Via WinCC: Complete range, via Control Panel: Manual ("Low limit" to 100) or automatic (0 to 100). The factory setting for "Low limit" is a fixed minimum value. MTBF: Operating hours after which the maximum brightness is reduced by half compared to the original value. MTBF is increased by using the integrated dimming function, for example time-controlled via screen saver or centrally via PROFIenergy. Input device TP700 Comfort Outdoor Touch screen (analog resistive) TP1500 Comfort Outdoor Yes, GFG (glass film glass) touch Memory TP700 Comfort Outdoor Usable memory for application data Usable memory for recipe data 1 2 MB Additional memory for options 12 MB Data memory card 2 System memory 1 2 TP1500 Comfort Outdoor 12 MB card 2 1 x MMC/SD combination slot 1 x SD slot Can be extended via memory card Memory cards are available as SIMATIC HMI accessories TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 31 Technical information 7.8 Description of the ports Interfaces TP700 Comfort Outdoor 1 x RS 422/485 (PROFIBUS) TP1500 Comfort Outdoor Max. 12 Mbps, applies to DP operations Ethernet (PROFINET) 2 x RJ45 10/100 Mbps 1 Audio Line In and Line Out USB 2.0 2 x Host 2 1 x Device 3 With integrated switch (one IP address only) USB type A; maximum load 500 mA USB type mini B (5-pin) 1 2 3 Power supply TP700 Comfort Outdoor Rated voltage TP1500 Comfort Outdoor 24 V DC Permitted voltage range +19.2 V to +28.8 V Rated current range, depends on the load 0.5 ... 1.0 A 0.8 ... 1.4 A Inrush current I2t 0.5 A2s Power 17 W 32 W Maximum permitted transient 35 V (500 ms) Minimum time between two transients 50 s Internal protection Electronic Miscellaneous TP700 Comfort Outdoor Buffered real-time clock 1 Audio reproduction Integrated or external via Line OUT Magnetic field intensity 1 TP1500 Comfort Outdoor Yes 50/60 Hz; 100 A/m RMS Battery backup typically 6 weeks 7.8 Description of the ports The specifications in "Comfort Panels" operating instructions apply. The X3 interface "PROFINET (LAN) 10/100/1000 Mbit" is not featured on the TP700 Comfort Outdoor and TP1500 Comfort Outdoor devices. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 32 Compact Operating Instructions, 05/2016, A5E35956909-AC Technical information 7.9 Scope of functions with WinCC 7.9 Scope of functions with WinCC The tables below show the objects which can be integrated in a project for an HMI device. Note The specified values are maximum values of the individual objects. Simultaneous use of multiple objects with their maximum value can lead to problems in the active project. Alarms Object Specification Alarms Number of discrete alarms Number of analog alarms Alarm length Number of tags / process values in an alarm Number of alarm classes Display TP700 Comfort Outdoor, TP1500 Comfort Outdoor 4000 200 80 characters Max. 8 32 Alarm window, alarm view Acknowledge error alarm individually Yes Edit alarm Yes Alarm indicator Yes ALARM_S Display S7 alarms Yes Alarm buffer, retentive Alarm buffer capacity 1024 Simultaneously queued alarm events 500 View alarm Yes Delete alarm buffer Yes Print alarms line by line Yes Tags, values and lists 1 Object Specification TP700 Comfort Outdoor, TP1500 Comfort Outdoor Tags Number 2048 Limit value monitoring Input/output Yes Linear scaling Input/output Yes Text lists Number 500 1 Graphics lists Number 500 1 The maximum total of text and graphics lists is 500. TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 33 Technical information 7.9 Scope of functions with WinCC Screens Object Specification Screens Number TP700 Comfort Outdoor, TP1500 Comfort Outdoor 500 Objects per screen 400 Tags per screen 400 Complex objects per screen (for example, bars) 20 Template Yes Recipes Object Specification TP700 Comfort Outdoor, TP1500 Comfort Outdoor Recipes Number 300 Data records per recipe 500 Entries per data record 1000 Recipe memory 256 KB Storage location 1 * Memory card (MMC/SD) * USB storage medium * Network drive The number of recipe data records may be restricted by the capacity of the storage medium. 1 Logs Note The HMI devices are suitable for the logging of relatively small volumes of data. Manage the data in several adjacent logs in a segmented circular log. The use of a large circular log has a negative effect on performance. Object Specification Logs Number of logs TP700 Comfort Outdoor, TP1500 Comfort Outdoor 50 Number of partial logs in a segmented circular log 400 Entries per log 1 20000 Filing format Storage location 1 CSV with ANSI character set, RDB, TXT * Memory card * USB storage medium * Network drive The number of entries in the log may be restricted by the capacity of the storage medium. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 34 Compact Operating Instructions, 05/2016, A5E35956909-AC Technical information 7.9 Scope of functions with WinCC Note Data consistency If the HMI device is switched off, the consistency of the stored data is only ensured with "SIMATIC HMI Memory Card" type memory cards. With commercially available memory cards, switching off the device may result in the loss of saved data, for example, due to a power failure. The consistency of data stored in logs is only guaranteed if you use RDB format. Only use "SIMATIC HMI Memory Card 2 GB" (SD) or higher. Safety Object Specification TP700 Comfort Outdoor, TP1500 Comfort Outdoor User view Number of user groups 50 Number of users 50 Number of authorizations / user permissions 32 Info texts Object Specification Info texts Length (no. of characters) TP700 Comfort Outdoor, TP1500 Comfort Outdoor 320 (depending on font) For alarms Yes For screens Yes For screen objects (e.g. I/O field, switch, button, invisible button) Yes Additional functions Object Specification TP700 Comfort Outdoor, TP1500 Comfort Outdoor Screen settings Touch screen calibration Yes Brightness setting Yes Language change Number of languages per project 32 VB Script User-specific extension of the functionality Yes Number of scripts 100 Graphic objects Vector and pixel graphics Yes Trends Number 300 Task planner Number of tasks 48 Text objects Number Direct keys PROFIBUS DP direct keys Yes PROFINET IO direct keys Yes 40000 TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 35 A Technical Support A.1 Service and support You can find additional information and support for the products described on the Internet at the following addresses: Technical support (http://www.siemens.de/automation/csi_en_WW) Support request form (http://www.siemens.com/automation/support-request) After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis) SIMATIC Documentation Collection (http://www.siemens.com/simatic-tech-doku-portal) Your local representative (http://www.automation.siemens.com/mcms/aspa-db/en/Pages/default.aspx) Training center (http://sitrain.automation.siemens.com/sitrainworld/?AppLang=en) Industry Mall (https://mall.industry.siemens.com) When contacting your local representative or Technical Support, please have the following information at hand: MLFB of the device BIOS version for industrial PC or image version of the device Other installed hardware Other installed software Tools & downloads Please check regularly if updates and hotfixes are available for download to your device. The download area is available on the Internet at the following link: After Sales Information System SIMATIC IPC/PG (http://www.siemens.com/asis) A.2 Troubleshooting and system alarms The specifications in "Comfort Panels" operating instructions apply. TP700 Comfort Outdoor, TP1500 Comfort Outdoor 36 Compact Operating Instructions, 05/2016, A5E35956909-AC Index A E Accessories, 9 Emission, 13 Alarm buffer, 33 ALARM_S, 33 F Alarms, 33 Figure, 4 Approvals, 25 B H HMI device Clearance, 17 Brightness Mounting, 20 Changing, 21 Brightness setting, 35 Technical specifications, 31 HMI devices Input device, 31 C Interfaces, 32 Changing Brightness, 21 Color depth, 21 Memory, 31 HMI devices Display, 31 Screen orientation, 21 Weight, 31 Clearance HMI device, 17 Color depth Changing, 21 Compact Operating Instructions Scope, 3 Convention I Info texts, 35 Input device HMI devices, 31 Installation Horizontal mounting, 16 Style, 3 Term, 4 Vertical, 16 Insulation test, 28 Interfaces D HMI devices, 32 Degree of pollution, 28 Degree of protection, 18, 28 Direct keys, 35 Display HMI devices, 31 Documentation Enclosed, 14 L Language change, 35 Lists, 33 Log Format, 34 Logs, 34 TP700 Comfort Outdoor, TP1500 Comfort Outdoor Compact Operating Instructions, 05/2016, A5E35956909-AC 37 Index M T Memory Tags, 33 HMI devices, 31 Technical specifications Mounting Display, 31 HMI device, 20 HMI devices, 31 Mounting clip Input device, 31 Mounting, 19 Interfaces, 32 Mounting cutout Memory, 31 Compatibility, 18 Power supply, 32 Dimensions, 18 Text objects, 35 Preparing, 18 Touch screen calibration, 35 Mounting position, 16 Transport damage, 14 Trends, 35 O Overvoltage category, 28 U Usage In residential areas, 13 P Industrial, 13 Power supply HMI devices, 32 Protection against ingress of solid foreign bodies, 28 Protection against water, 28 Protection class, 28 With additional measures, 13 User view, 35 V VB Script, 35 R Radio interference, 13 W Recipes, 34 Weight HMI devices, 31 S Safety instruction General, 13 Storage, 27 Transportation, 27 Scheduler, 35 Screen orientation Changing, 21 Screens, 34 TP700 Comfort Outdoor, TP1500 Comfort Outdoor 38 Compact Operating Instructions, 05/2016, A5E35956909-AC