6AG1124-0GC13-2AX0 - SIEMENS

Comfort Outdoor

___________________

SIMATIC HMI

HMI devices

TP700 Comfort Outdoor,

TP1500 Comfort Outdoor

Compact Operating Instructions

05/2016

A5E35956909

-AC

Preface

Overview

Safety instructions

Mounting and connecting the

HMI device

Configuring the device

Commissioning a project

Maintenance and care

Technical information

Technical Support

Siemens AG

Division Digital Factory

Postfach 48 48

90026 NÜRNBERG

GERMANY

A5E35956909-AC

Ⓟ

05/2016 Subject to change

Legal information

Warning notice system

This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent

damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert

symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are

graded according to the degree of danger.

DANGER

indicates that death or severe personal injury will result if proper precautions are not taken.

WARNING

indicates that death or severe personal injury may result if proper precautions are not taken.

CAUTION

indicates that minor personal injury can result if proper precautions are not taken.

NOTICE

indicates that property damage can result if proper precautions are not taken.

If more than one degree of danger is present, the warning notice representing the highest degree of danger will

be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to

property damage.

Qualified Personnel

The product/system described in this documentation may be operated only by

personnel qualified

for the specific

task in accordance with the relevant documentation, in particular its warning notices and safety instructions.

Qualified personnel are those who, based on their training and experience, are capable of identifying risks and

avoiding potential hazards when working with these products/systems.

Proper use of Siemens products

Note the following:

WARNING

Siemens products may only be used for the applications described in the catalog and in the relevant technical

documentation. If products and components from other manufacturers are used, these must be recommended

or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and

maintenance are required to ensure that the products operate safely and without any problems. The permissible

ambient conditions must be complied with. The information in the relevant documentation must be observed.

Trademarks

All names identified by ® are registered trademarks of Siemens AG. The remaining trademarks in this publication

may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.

Disclaimer of Liability

We have reviewed the contents of this publication to ensure consistency with the hardware and software

described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the

information in this publication is reviewed regularly and any necessary corrections are included in subsequent

editions.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 3

Preface

Scope

These compact operating instructions apply to the following HMI devices in conjunction with

the WinCC software package:

● TP700 Comfort Outdoor, article number 6AV2124-0GC13-0AX_

● TP1500 Comfort Outdoor, article number 6AV2124-0QC13-0AX_

"_" stands for the variant key of the article number.

These compact operating instructions describe the technical differences of the Outdoor

devices to the corresponding standard devices.

The information in these compact operating instructions take precedence in terms of their

binding character over the statements in the following underlying operating instructions, the

release notes and the online help.

Operating instructions on the Comfort Panels

(http://support.automation.siemens.com/WW/view/en/49313233)

Note

This document belongs to the device and will also be required for repeat commissioning.

Keep all supplied and supplementary documentation for the entire service life of the

device.

Provide all associated documents to any future owner of the device.

Style conventions

Style Convention

Scope

"Add screen" • Terminology that appears in the user interface, for example,

dialog names, tabs, buttons, menu commands

• Required input, for example, limits, tag values.

• Path information

"File > Edit" Operational sequences, for example, menu commands, shortcut

menu commands.

Keyboard operation

Please observe notes labeled as follows:

Note

A note

contains important information about the product described in the manual and its use,

or a specific section of the manual to which you should pay particular attention.

Preface

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

4 Compact Operating Instructions, 05/2016, A5E35956909-AC

Naming conventions

Term

Applies to

System • System

• Machining center

• One or more machines

HMI device

Device

• TP700 Comfort Outdoor

• TP1500 Comfort Outdoor

WinCC

WinCC V13 SP1 (TIA Portal)

Figures

This document contains figures of the devices described. The figures can deviate from the

particularities of the delivered device.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 5

Table of contents

Preface ................................................................................................................................................... 3

1 Overview................................................................................................................................................. 7

1.1 Product description ................................................................................................................... 7

1.2 Software requirements .............................................................................................................. 8

1.3 Scope of delivery ...................................................................................................................... 9

1.4 Configuration of the devices ................................................................................................... 10

1.4.1 Device views ........................................................................................................................... 10

1.4.2 Interfaces ................................................................................................................................ 11

2 Safety instructions ................................................................................................................................. 12

2.1 General safety instructions ..................................................................................................... 12

2.2 Notes about usage .................................................................................................................. 13

3 Mounting and connecting the HMI device .............................................................................................. 14

3.1 Preparing for installation ......................................................................................................... 14

3.1.1 Checking the package contents .............................................................................................. 14

3.1.2 Checking the operating conditions .......................................................................................... 15

3.1.3 Selecting a mounting position ................................................................................................. 15

3.1.4 Checking clearances............................................................................................................... 17

3.1.5 Preparing the mounting cutout ................................................................................................ 17

3.2 Mounting the device ................................................................................................................ 19

3.3 Connecting the device ............................................................................................................ 20

4 Configuring the device .......................................................................................................................... 21

4.1 Overview ................................................................................................................................. 21

4.2 Changing the brightness settings ........................................................................................... 21

5 Commissioning a project ....................................................................................................................... 23

5.1 Overview ................................................................................................................................. 23

5.2 Using existing projects ............................................................................................................ 23

6 Maintenance and care ........................................................................................................................... 24

6.1 Cleaning the device ................................................................................................................ 24

6.2 Repair, spare parts, recycling and disposal ............................................................................ 24

Table of contents

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

6 Compact Operating Instructions, 05/2016, A5E35956909-AC

7 Technical information ............................................................................................................................ 25

7.1 Certificates and approvals ..................................................................................................... 25

7.2 Electromagnetic compatibility ................................................................................................ 25

7.2.1 Emitted interference ............................................................................................................... 25

7.2.2 Immunity to interferences ....................................................................................................... 25

7.3 Mechanical ambient conditions .............................................................................................. 26

7.3.1 Storage conditions ................................................................................................................. 26

7.3.2 Operating Conditions ............................................................................................................. 26

7.4 Climatic ambient conditions ................................................................................................... 26

7.4.1 Long-term storage .................................................................................................................. 26

7.4.2 Transport and short-term storage .......................................................................................... 27

7.4.3 Operating Conditions ............................................................................................................. 27

7.5 Information on insulation tests, protection class and degree of protection ............................ 28

7.6 Dimension drawings ............................................................................................................... 29

7.6.1 Dimension drawings of the TP700 Comfort Outdoor ............................................................. 29

7.6.2 Dimension drawings of the TP1500 Comfort Outdoor ........................................................... 30

7.7 Specifications ......................................................................................................................... 31

7.8 Description of the ports .......................................................................................................... 32

7.9 Scope of functions with WinCC .............................................................................................. 33

A Technical Support ................................................................................................................................. 36

A.1 Service and support ............................................................................................................... 36

A.2 Troubleshooting and system alarms ...................................................................................... 36

Index .................................................................................................................................................... 37

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 7

Overview

1.1

Product description

SIMATIC Comfort Outdoor devices with glass touch screen and powder-coated, UV-resistant

aluminum front are designed for use in indoor and outdoor areas, for example, in the fields of

Oil&Gas, Marine or Refrigeration Technology.

All devices offer the same excellent functionality and are configured exclusively with the

innovative HMI software, WinCC. The engineering software is integrated in the engineering

framework, "Totally Integrated Automation Portal".

Overview

1.2 Software requirements

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

8 Compact Operating Instructions, 05/2016, A5E35956909-AC

Features

Front

• External dimensions of the front and mounting cutout correspond to the

standard product

• Durable powder coating

• High UV resistance

• GFG (Glass-Film-Glass) touch screens, analog resistive

• Manual or automatic brightness control with brightness sensor

Display

• High-resolution TFT display in widescreen format with 16 million colors

• Suitable for use in daylight

• Anti-reflective and bonded for glare-free reading

Touch screen

• Resistive single touch screen

• Suitable for operation with gloves, pen and fingers

Interfaces

• 2 PROFINET interfaces

• 1 PROFIBUS interface

• USB 2.0 ports:

– 2 x USB host interface (type A)

– 1 x USB device interface (type mini B)

Mechanical differences to the standard product

Device depth

The Comfort Outdoor devices are deeper than the corresponding Comfort HMI

device.

Read the information in the following sections:

• Preparing the mounting cutout (Page 17)

• Dimension drawings (Page 29)

Slots for SD

memory cards

The protection mechanism of the SD memory card for the Comfort Outdoor

devices is mechanically differently than that of the corresponding Comfort HMI

device. The safety tab is not required with the Comfort Outdoor devices.

1.2

Software requirements

You require the software WinCC V13 SP1 (TIA Portal) Update 6 with the Hardware Support

Package "HSP0149 HMI TP700_1500 Comfort Outdoor" or later versions. You can find the

software under Technical Support on the Internet.

Overview

1.3 Scope of delivery

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 9

1.3

Scope of delivery

The following components are included in the scope of delivery of the HMI device.

Name

Figure

Quantity

HMI device

Installation instructions

(Quick Install Guide)

Mounting clips

Aluminum mounting clip 8 TP700 Comfort Outdoor

Steel mounting clip 12 TP1500 Comfort Outdoor

Strain relief Example: Strain relief

1 TP700 Comfort Outdoor

Power supply terminal Connector, female, 2-pin, type 1

Some components in the scope of delivery are also available as accessories, see

"Accessories" section in the Comfort Panels operating instructions or directly in the Industry

Mall (https://mall.industry.siemens.com).

Overview

1.4 Configuration of the devices

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

10 Compact Operating Instructions, 05/2016, A5E35956909-AC

1.4

Configuration of the devices

1.4.1

Device views

This section describes the basic design of the device using the example of the

TP700 Comfort Outdoor.

Front view and side view

①

Light sensor

②

Aluminum front, powder coated

③

Glass touch screen / display

④

Cutouts for attaching the mounting clamps

Rear view

①

Rating plate

②

Slot for data memory card

③

Slot for system memory card

④

Interface inscription

Overview

1.4 Configuration of the devices

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 11

1.4.2

Interfaces

Position of the interfaces

The figure below shows the interfaces of the HMI devices.

①

X80 power supply connector

⑤

X1 PROFINET (LAN), 10/100 Mb

②

Connection for equipotential bonding (ground)

⑥

X90 Audio Line IN / OUT

③

X2 PROFIBUS (Sub-D RS422/485)

⑦

X60 USB type Mini B

④

X61 / X62 USB type A

Additional information

Use the X1 or X60 interface to connect a configuration PC. Use the X61 / X62 interfaces to

connect peripheral devices such as a printer or keyboard. Use the X90 interface to connect a

loudspeaker.

You can fasten the USB and PROFINET connecting cables to the rear panel of the

HMI device with cable ties.

Secure the cables with a separate strain relief for the TP700 Comfort Outdoor. Install the

strain relief on the HMI device.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

12 Compact Operating Instructions, 05/2016, A5E35956909-AC

Safety instructions

2.1

General safety instructions

The general safety instructions in the "Comfort Panel" operating instructions apply.

Also note the following for Comfort outdoor devices:

WARNING

Unintended functions may be triggered with icing

If the operating temperature is below 2 °C, icing may occur on the front of the device. Icing

may trigger unintended functions in some circumstances.

To avoid triggering unintended functions, you can take the following measures, for

example:

• Install an additional enabling switch in your plant for operator actions that initiate a

dangerous operating state.

• Assign a password to operator actions or inputs that initiate a dangerous operating

state.

Safety instructions

2.2 Notes about usage

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 13

2.2

Notes about usage

Industrial applications

The HMI device is designed for outdoor areas in industrial applications. It conforms to the

following standards:

● Requirements of the emission standard for industrial environments,

EN 61000-6-4: 2007 + A1:2011

● ESD immunity requirements to DIN EN 61000-6-2:2005

Use in residential areas

Note

The HMI device is not intended for use in residential areas. Operation of an HMI device in

residential areas can have a negative influence on

radio/TV reception.

If the HMI device is used in a residential area, you must take measures to achieve

Limit Class B conforming to EN 55011 for RF interference.

Individual acceptance is required.

Use with additional measures

The HMI device should not be used at the following locations unless additional measures are

taken:

● In locations with a high degree of ionizing radiation

● In locations with severe operating conditions, for example, due to:

– Corrosive vapors, gases, oils or chemicals

– Electrical or magnetic fields of high intensity

● In systems that require special monitoring, for example, in:

– Elevators

– Systems in especially hazardous rooms

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

14 Compact Operating Instructions, 05/2016, A5E35956909-AC

Mounting and connecting the HMI device

3.1

Preparing for installation

3.1.1

Checking the package contents

Check the package content for visible signs of transport damage and for completeness.

Note

Damaged parts

A damaged part will cause the HMI device to malfunction.

Do not install parts damaged during shipment. In the case of

damaged parts, contact your

Siemens representative.

Check the scope of supply of the HMI device (see Scope of delivery (Page 9)).

Additional documents may be included in the delivery.

The documentation is part of the HMI device and is required for subsequent commissioning.

Keep all enclosed documentation for the entire service life of the HMI device. You must pass

along the enclosed documentation to any subsequent owner or user of the HMI device.

Make sure that every supplement to the documentation that you receive is stored together

with the operating instructions.

Mounting and connecting the HMI device

3.1 Preparing for installation

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 15

3.1.2

Checking the operating conditions

Note the following aspects before installing the HMI device:

1. Familiarize yourself with the technical specifications for operating the HMI device. You

can find this information in the section "Technical information (Page 25)".

2. Read the information about local use of the HMI device, see section

"Notes about usage (Page 13)".

3.1.3

Selecting a mounting position

The device is suitable for installation in:

● Mounting cabinets

● Control cabinets

● Switchboards

● Consoles

In the following, all of these mounting options are referred to by the general term "cabinet".

The device is self-ventilated and approved for inclined mounting at angles up to +/-35° from

the vertical in stationary cabinets.

NOTICE

Damage due to overheating

Inclined installation reduces the convection by the device and therefore the maximum

permitted ambient temperature for operation.

If there is sufficient forced ventilation, the device can also be operated in the inclined

mounting position up to the maximum permitted ambient temperature for vertical

installation. The device may otherwise be damaged and its certifications and warranty will

be rendered null and void.

The ambient temperature ranges listed in this section apply to the temperature inside the

cabinet.

Mounting and connecting the HMI device

3.1 Preparing for installation

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

16 Compact Operating Instructions, 05/2016, A5E35956909-AC

Mounting position

Select one of the approved mounting positions for your device. The approved mounting

positions are described in the following sections.

Mounting in horizontal format

Ambient temperature when mounted in horizontal format:

● Vertical mounting (0° inclined): Maximum +60 °C

● Inclined mounting (inclined up to 35°): Maximum +50 °C

Mounting in vertical format

Ambient temperature when mounted in vertical format:

● Vertical mounting (0° inclined): Maximum +50 °C

● Inclined mounting (inclined up to 35°): Maximum +45 °C

See also

Operating Conditions (Page 27)

Mounting and connecting the HMI device

3.1 Preparing for installation

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 17

3.1.4

Checking clearances

The following clearances are required around the HMI device to ensure sufficient self-

ventilation:

● At least 15 mm to both the right and left of the mounting cutout (in x direction) to allow for

insertion of the mounting clips during installation

● At least 50 mm above and 50 mm below the mounting cutout (in the y direction) for

ventilation

● At least 10 mm behind the rear panel of the HMI device (in the z direction)

The following figure shows the clearances during mounting of the HMI devices in horizontal

and vertical formats:

Note

Ensure that the maximum ambient temperature is not exceeded when mounting the device

in a cabinet and especially in a closed enclosure.

3.1.5

Preparing the mounting cutout

Note

Stability of the mounting cutout

The material in the area of the mounting

cutout must provide sufficient strength to guarantee

lasting and safe mounting of the HMI device.

To achieve the degrees of protection described below, it must be ensured that deformation

of the material cannot occur due to the force of the mounting clips

or operation of the device.

Mounting and connecting the HMI device

3.1 Preparing for installation

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

18 Compact Operating Instructions, 05/2016, A5E35956909-AC

Degrees of protection

The degrees of protection of the HMI device can only be guaranteed if the following

requirements are met:

● Material thickness at the mounting cutout for a protection rating of IP66 or Front face

only Type 4X/Type 12 (Indoor/Outdoor): 2 mm to 6 mm

● Permitted deviation from plane at the mounting cutout: ≤ 0.5 mm

This condition must be met for the mounted HMI device.

● Permitted surface roughness in the area of the mounting seal: ≤ 120 µm (Rz 120)

Compatibility of the mounting cutout to other HMI devices

The mounting cutouts of the following HMI devices are compatible with the mounting cutouts

of the following predecessor devices:

HMI device

Mounting cutout compatible with

TP700 Comfort Outdoor

TP700 Comfort, TP 177B 6", MP 177 6", TP 277 6"

TP1500 Comfort Outdoor TP1500 Comfort

Please note that although the dimensions for the mounting cutout are the same, the device

depth and/or the enclosure front dimensions may differ from the respective dimensions of the

predecessor devices.

Dimensions of the mounting cutout

Width and height should be reversed accordingly when mounting in vertical format.

Mounting and connecting the HMI device

3.2 Mounting the device

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 19

Mounting depth

The mounting depth of the devices is:

HMI device

Mounting depth

TP700 Comfort Outdoor

67 mm

TP1500 Comfort Outdoor 77 mm

3.2

Mounting the device

Positions of the mounting clips

To achieve the degree of protection for the HMI device, the positions for the mounting clips

shown below must be adhered to.

The positions of the mounting clips are marked by stamps on the cutouts. Fit the mounting

clips in all the stamped cutouts.

The following table shows the type, number, and position of the mounting clips needed for

the respective HMI devices.

HMI device

Mounting clips

Type

Number

Position on the HMI device

TP700 Comfort Outdoor Aluminum

mounting clip

TP1500 Comfort Outdoor Steel

mounting clip

Requirement

● All packaging components and protective films were removed from the HMI device.

● To install the HMI device, you need the mounting clips from the accessories kit.

● The mounting seal must be installed on the HMI device.

Mounting and connecting the HMI device

3.3 Connecting the device

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

20 Compact Operating Instructions, 05/2016, A5E35956909-AC

Procedure

Note

Risk of guaranteed degree of protection not being met

If the mounting seal is damaged, the degree of protection is not guaranteed.

Replace the

device in this case.

Note

Installation of the HMI device

Always mount the HMI device according to the instructions in this manual.

Mounting clips for TP700 Comfort Outdoor:

Mounting clips for TP1500 Comfort Outdoor:

Proceed as follows:

1. Insert the HMI device into the mounting cutout from the front.

2. Insert the mounting clamp into the cutout provided on the HMI device.

3. Tighten the mounting clamp with the setscrew.

Note

Adhere to the permitted torque when tightening the setscrew of the mounting clamp:

0.5

4. Repeat steps 2 and 3 for all mounting clips.

5. Check the fit of the device in the mounting cutout.

3.3

Connecting the device

The specifications in "Comfort Panels" operating instructions apply.

The X3 interface "PROFINET (LAN) 10/100/1000 Mbit" is not featured on the

TP700 Comfort Outdoor and TP1500 Comfort Outdoor devices.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 21

Configuring the device

4.1

Overview

The specifications in the "Comfort Panel" operating instructions apply for commissioning and

parameter assignments.

The enhanced brightness control of the Comfort Panels Outdoor differs from the other

Comfort HMI devices and is described in the following section.

4.2

Changing the brightness settings

The Comfort Outdoor Panels feature a manual or automatic brightness control with a

brightness sensor. Make the appropriate settings in the Control Panel.

Requirement

The Control Panel is open.

Set brightness

Proceed as follows:

1. Open the "Display Properties" dialog with the Display icon.

2. Switch to the "Brightness" tab. The figure below shows the factory settings.

Configuring the device

4.2 Changing the brightness settings

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

22 Compact Operating Instructions, 05/2016, A5E35956909-AC

Select the "Manual" or "Auto" option.

– In the "Manual" mode, you can adjust the brightness to the desired value using the

slider.

Note

"Manual" mode

A change in the brightness value through the

configuration takes precedence over the

manual setting.

– in the "Auto" mode, you can set the minimum and maximum brightness for the

automatic brightness control of the HMI device under "Brightness Range".

NOTICE

"Auto" mode (factory state)

The brightness parameters are controlled by the light sensor in "Auto" mode. The

brightness can no longer be changed manually or through the configuration.

The "Screen saver" function is available as usual.

3. If you want to check the settings without closing the dialog, press the "Apply" button.

4. To discard the settings and close the dialog, press the "Cancel".

button. To save the settings and close the dialog, press the "OK" button.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 23

Commissioning a project

5.1

Overview

The specifications in "Comfort Panels" operating instructions apply.

5.2

Using existing projects

Proceed as follows to transfer an existing project to the HMI device:

1. Open the existing project in WinCC (TIA Portal).

2. Make sure that the project is dimensioned within the functional scope of the HMI device,

see section "Scope of functions with WinCC (Page 33)".

Note

The functional scope of the TP1500 Comfort Outdoor corresponds to the functional scope

of a TP1200 Comfort.

3. Replace the HMI device in WinCC.

4. Transfer the project to the HMI device as described in the "Comfort Panel" operating

instructions.

Note

"Backup, Restore" and "Automatic Backup" only for devices with identical article numbers

The "Backup" and "Restore" function using a data memory card and the "Automatic Backup"

function using the system memory card are only available for devices with identical article

numbers.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

24 Compact Operating Instructions, 05/2016, A5E35956909-AC

Maintenance and care

6.1

Cleaning the device

The specifications in "Comfort Panels" operating instructions apply.

NOTICE

Disable or switch off the device while cleaning

Switch off the HMI device or activate the clean screen when you clean the appliance during

operation.

Note

Cleaning of the coated glass touch screen

Take care not to damage the glass touch screen and the coating of the

touch screen on

Comfort Outdoor devices.

Use a cleaning cloth and dishwashing liquid or foaming screen cleaners. Apply as little

pressure as possible on the touch screen when cleaning.

6.2

Repair, spare parts, recycling and disposal

The specifications in "Comfort Panels" operating instructions apply.

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 25

Technical information

7.1

Certificates and approvals

Approvals

The device is certified as shown on the rear of the device.

As soon as additional certificates are available, you can find them in the Industry Mall or

Technical Support.

Search for your device and use the link "Support > Approvals / Certificates".

7.2

Electromagnetic compatibility

The device is designed for industrial use.

7.2.1

Emitted interference

The device meets the requirements according to EN 61000-6-4. The device corresponds to

limit class A.

Note

The HMI device is not intended for use in residential areas. Operation of an HMI device in

residential areas

can have a negative influence on radio/TV reception.

7.2.2

Immunity to interferences

The device meets the requirements according to EN 61000-6-2.

Technical information

7.3 Mechanical ambient conditions

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

26 Compact Operating Instructions, 05/2016, A5E35956909-AC

7.3

Mechanical ambient conditions

7.3.1

Storage conditions

The following information is for a device that is transported and stored in its original

packaging.

The device meets the requirements according to IEC 60721-3-2 Class 2M2 with the following

amendments and limitations:

Type of condition

Permitted range

Free fall

≤ 1 m

Vibration to IEC 60068-2-6 5 .. 8.4 Hz, deflection 3.5 mm

8.4 ... 500 Hz, acceleration 1 g

Shock to IEC 60068-2-27

250 m/s

, 6 ms, 1000 shocks

7.3.2

Operating Conditions

The following information applies to a device installed according to the specifications in these

operating instructions.

The device meets the requirements according to IEC 60721 Class 3M3 with the following

amendments and limitations:

Type of condition

Permitted range

Vibration to IEC 60068-2-6 5 ... 8.4 Hz, deflection 3.5 mm

8.4 ... 200 Hz, acceleration 1 g

Shock to IEC 60068-2-27

150 m/s

, 11 ms, 3 shocks

7.4

Climatic ambient conditions

7.4.1

Long-term storage

The following information applies to a device that is stored in its original packaging for longer

than two weeks.

The device meets the requirements of IEC 60721-3-1 Class 1K2.

Technical information

7.4 Climatic ambient conditions

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 27

7.4.2

Transport and short-term storage

The following information applies to a device that is transported in the original packaging and

weather-proof packaging, and stored from some time.

The device meets the requirements according to IEC 60721-3-2 Class 2K4 with the following

amendments and limitations:

Type of condition

Permitted range

Temperature

–30 ... 70 °C

Atmospheric pressure 1080 ... 660 hPa, corresponds to an elevation of -1000 to 3500 m

Relative humidity

10 ... 90 %

Pollutant concentration SO2: < 0.5 ppm; relative humidity < 60 %, no condensation

H2S: < 0.1 ppm; relative humidity < 60 %, no condensation

Note

If dewing has developed, wait approximately 4 hours until the HMI device has dried

completely before switching it on.

Do not expose the HMI device to direct radiation from a heater.

7.4.3

Operating Conditions

The following information applies to a device installed according to the specifications in these

compact operating instructions.

The HMI device is designed for stationary operation according to IEC 60721.

The device meets the requirements according to IEC 60721-3-3 Class 3K3 with the following

amendments and limitations:

Type of condition

Permitted range

Mounting position

Elevation

-1000 ... 2000 m

Elevation

3000 m *

Temperature,

Mounting in horizontal format

Vertical

-30 ... 60 °C

-30 ... 54 °C

Inclined, maximum inclination 35°

-30 ... 50 °C

-30 ... 45 °C

Temperature,

Mounting in vertical format

Vertical

-30 ... 50 °C

-30 ... 45 °C

Inclined, maximum inclination 35°

-30 ... 45 °C

-30 ... 40 °C

Atmospheric pressure,

operation elevation

1080 ... 795 hPa, corresponds to an elevation of -1000 to 2000 m

795 ... 701 hPa, corresponds to an elevation of 2000 ... 3000 m

Relative humidity

From 10 to 90%, without condensation

Pollutant concentration SO2: < 0.5 ppm; relative humidity < 60 %, no condensation

S: < 0.1 ppm; relative humidity < 60 %, no condensation

* Interpolation of the maximum temperature value is permitted in the range of 2000 ... 3000 m.

Note

The system components connected to the HMI device, the

power supply for example, must

also be suited to the respective operating conditions.

Technical information

7.5 Information on insulation tests, protection class and degree of protection

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

28 Compact Operating Instructions, 05/2016, A5E35956909-AC

7.5

Information on insulation tests, protection class and degree of

protection

Insulation test

The insulation strength is demonstrated in the type test with the following test voltages in

accordance with IEC 61131-2:

Circuits with rated voltage of Ui

Test voltage

Insulation tested with (type test)

707 V DC to other circuits / to ground

Degree of pollution and overvoltage category

The device meets the following requirements according to IEC 61131-2:2007:

Degree of pollution 2 (front)

1 (rear)

Overvoltage category II

Protection class

Protection class III according to IEC 61131-2

Protection against foreign objects and water

The device meets the requirements according to EN 60529.

Device side

Degree of protection

Front When mounted:

• IP66

• Type 4X/Type 12 (Indoor/Outdoor)

Rear panel IP20

Protection against contact with standard test probes. There

is no protection against the ingress of water.

The front protection rating can only be guaranteed if the mounting seal lies flush against the

mounting cutout. Read the corresponding information in section

"Preparing the mounting cutout (Page 17)".

Technical information

7.6 Dimension drawings

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 29

7.6

Dimension drawings

7.6.1

Dimension drawings of the TP700 Comfort Outdoor

Technical information

7.6 Dimension drawings

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

30 Compact Operating Instructions, 05/2016, A5E35956909-AC

7.6.2

Dimension drawings of the TP1500 Comfort Outdoor

Technical information

7.7 Specifications

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 31

7.7

Specifications

Weight

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

Weight without packaging

approx. 1.5 kg

4.0 kg

Display

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

Type

LCD TFT

Active display area 7.0''

152 mm x 91 mm

15.4''

331 x 207 mm

Resolution 800 x 480 pixels 1280 x 800 pixels

Possible colors

Up to 16 million

Brightness control

Manual/automatic, value range 0 to 100

, 0 = backlighting off

Backlighting

Half Brightness Life Time (MTBF

)

LED

50000 h

Pixel error class in accordance with

ISO 9241-307

Via WinCC: Complete range, via Control Panel: Manual ("Low limit" to 100) or automatic (0 to 100). The factory setting

for "Low limit" is a fixed minimum value.

MTBF: Operating hours after which the maximum brightness is reduced by half compared to the original value. MTBF is

increased by using the integrated dimming function, for example time-controlled via screen saver or centrally via

PROFIenergy.

Input device

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

Touch screen (analog resistive)

Yes, GFG (glass film glass) touch

Memory

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

Usable memory for application data

12 MB

Usable memory for recipe data

2 MB

Additional memory for options

12 MB

Data memory card

1 x MMC/SD combination slot

System memory card

1 x SD slot

Can be extended via memory card

2 Memory cards are available as SIMATIC HMI accessories

Technical information

7.8 Description of the ports

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

32 Compact Operating Instructions, 05/2016, A5E35956909-AC

Interfaces

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

1 x RS 422/485 (PROFIBUS)

Max. 12 Mbps, applies to DP operations

Ethernet (PROFINET) 2 x RJ45 10/100 Mbps 1

Audio

Line In and Line Out

USB 2.0 2 x Host 2

1 x Device 3

With integrated switch (one IP address only)

USB type A; maximum load 500 mA

3 USB type mini B (5-pin)

Power supply

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

Rated voltage

Permitted voltage range

24 V DC

+19.2 V to +28.8 V

Rated current range,

depends on the load

0.5 ... 1.0 A 0.8 ... 1.4 A

Inrush current I

0.5 A

Power

17 W

32 W

Maximum permitted transient

35 V (500 ms)

Minimum time between two transients

50 s

Internal protection

Electronic

Miscellaneous

TP700 Comfort Outdoor

TP1500 Comfort Outdoor

Buffered real-time clock

Yes

Audio reproduction

Integrated or external via Line OUT

Magnetic field intensity

50/60 Hz; 100 A/m RMS

1 Battery backup typically 6 weeks

7.8

Description of the ports

The specifications in "Comfort Panels" operating instructions apply.

The X3 interface "PROFINET (LAN) 10/100/1000 Mbit" is not featured on the

TP700 Comfort Outdoor and TP1500 Comfort Outdoor devices.

Technical information

7.9 Scope of functions with WinCC

TP700 Comfort Outdoor, TP1500 Comfort Outdoor

Compact Operating Instructions, 05/2016, A5E35956909-AC 33

7.9

Scope of functions with WinCC

The tables below show the objects which can be integrated in a project for an HMI device.

Note

The specified values are maximum values of the individual objects. Simultaneous use of

multiple objects with their maximum value can lead to problems in the active project.

Alarms

Object

Specification

TP700 Comfort Outdoor,

TP1500 Comfort Outdoor

Alarms

Number of discrete alarms

4000

Number of analog alarms

200

Alarm length

80 characters

Number of tags / process values in an alarm

Max. 8

Number of alarm classes

Display

Alarm window, alarm view

Acknowledge error alarm individually

Yes

Edit alarm

Yes

Alarm indicator

Yes

ALARM_S

Display S7 alarms

Yes

Alarm buffer, retentive

Alarm buffer capacity

1024

Simultaneously queued alarm events

500

View alarm

Yes

Delete alarm buffer Yes

Print alarms line by line

Yes

Tags, values and lists

Object

Specification

TP700 Comfort Outdoor,

TP1500 Comfort Outdoor