G3RV-SR700-AL AC/DC24 - OMRON

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TOSHIBA Bipolar Linear Integrated Circuit Silicon Monolithic

TA7805SB, TA78057SB, TA7806SB, TA7807SB, TA7808SB, TA7809SB,

TA7810SB, TA7812SB, TA7815SB, TA7818SB, TA7820SB, TA7824SB

Three-Terminal Positive Voltage Regulators

5 V, 5.7 V, 6 V, 7 V, 8 V, 9 V, 10 V, 12 V, 15 V, 18 V, 20 V, 24 V

Features

z Suitable for CMOS, TTL and the power supply of other digital

ICs

z Internal thermal shutdown protection

z Internal overcurrent protection

z Maximum output current of 1 A

z Package in the plastic case TPL (PD: 1.8 W)

Pin Assignment

1 3

OUT GND

Marking side

Marking

Note 1: The “**” in the each product number is replaces with the output voltage of each product.

Note 2: A line under a Lot No. identifies the indication of product Labels.

Not underlined: [[Pb]]/INCLUDES > MCV

Underlined: [[G]]/RoHS COMPATIBLE or [[G]]/RoHS [[Pb]]

Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS

compatibility of Product. The RoHS is the Directive 2002/95/EC of the European Parliament and of the Council of 27

January 2003 on the restriction of the use of certain hazardous substances in electrical and electronic equipment.

The product(s) in this document (“Product”) contain functions intended to protect the Product from

temporary small overloads such as minor short-term overcurrent or overheating. The protective

functions do not necessarily protect Product under all circumstances. When incorporating Product into

your system, please design the system (1) to avoid such overloads upon the Product, and (2) to shut

down or otherwise relieve the Product of such overload conditions immediately upon occurrence. For

details, please refer to the notes appearing below in this document and other documents referenced in

this document.

SIP3-P-2.50A

Weight: 1.5 g (Typ.)

Note 2

Lot No.

Part No. (or abbreviation code) Note 1

78**SB

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

Equivalent Circuit

Absolute Maximum Ratings (Ta = 25°C)

Characteristics Symbol Rating Unit

TA7805SB

TA78057SB

TA7806SB

TA7807SB

TA7808SB

TA7809SB

TA7810SB

TA7812SB

TA7815SB

TA7818SB

TA7820SB

Input voltage

TA7824SB

VIN

Output current I OUT 1 A

Power dissipation (Ta = 25°C) PD 1.8 W

Operating temperature Topr −30 to 85 °C

Storage temperature Tstg −55 to 150 °C

Junction temperature Tj 150 °C

Thermal resistance junction to

ambient Rth (j-a) 69.4 °C/W

Note 3: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the

significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even

if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum

ratings and the operating ranges.

Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook

(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test

report and estimated failure rate, etc).

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7805SB

Electrical Characteristics

(Unless otherwise specified, VIN = 10 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 4.8 5.0 5.2 V

7.0 V ≤ VIN ≤ 25 V ― 3 100

Line regulation Reg·line 1 Tj = 25°C

8.0 V ≤ VIN ≤ 12 V ― 1 50

5 mA ≤ IOUT ≤ 1.0 A ― 15 100

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 5 50

Output voltage VOUT 1 Tj = 25°C 7.0 V ≤ VIN ≤ 20 V,

5.0 mA ≤ IOUT ≤ 1.0 A 4.75 ― 5.25 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.2 8.0 mA

Quiescent current change ΔIB 1 7.0 V ≤ VIN ≤ 25 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.3 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 50 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 8.0 V ≤ VIN ≤ 18 V,

IOUT = 50 mA, Tj = 25°C 62 78 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 1.6 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −0.6 ― mV/°C

TA78057SB

Electrical Characteristics

(Unless otherwise specified, VIN = 10.7 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 5.47 5.7 5.93 V

7.7 V ≤ VIN ≤ 25 V ― 4 110

Line regulation Reg·line 1 Tj = 25°C

8.7 V ≤ VIN ≤ 12.7 V ― 2 55

5 mA ≤ IOUT ≤ 1.0 A ― 15 110

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 5 55

Output voltage VOUT 1 Tj = 25°C 7.7 V ≤ VIN ≤ 20.7 V,

5.0 mA ≤ IOUT ≤ 1.0 A 5.42 ― 5.98 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 7.7 V ≤ VIN ≤ 25 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.3 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 55 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 8.8 V ≤ VIN ≤ 18.8 V,

IOUT = 50 mA, Tj = 25°C 62 77 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 1.5 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −0.7 ― mV/°C

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7806SB

Electrical Characteristics

(Unless otherwise specified, VIN = 11 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 5.75 6.0 6.25 V

8.0 V ≤ VIN ≤ 25 V ― 4 120

Line regulation Reg·line 1 Tj = 25°C

9 V ≤ VIN ≤ 13 V ― 2 60

5 mA ≤ IOUT ≤ 1.0 A ― 15 120

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 5 60

Output voltage VOUT 1 Tj = 25°C 8 V ≤ VIN ≤ 21 V,

5.0 mA ≤ IOUT ≤ 1.0 A 5.7 ― 6.3 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 8.0 V ≤ VIN ≤ 25 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.3 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 55 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 9 V ≤ VIN ≤ 19 V,

IOUT = 50 mA, Tj = 25°C 61 77 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 1.5 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −0.7 ― mV/°C

TA7807SB

Electrical Characteristics

(Unless otherwise specified, VIN = 12 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 6.72 7.0 7.28 V

9 V ≤ VIN ≤ 25 V ― 5 140

Line regulation Reg·line 1 Tj = 25°C

10 V ≤ VIN ≤ 14 V ― 2 70

5 mA ≤ IOUT ≤ 1.0 A ― 15 140

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 5 70

Output voltage VOUT 1 Tj = 25°C 9 V ≤ VIN ≤ 22 V,

5.0 mA ≤ IOUT ≤ 1.0 A 6.65 ― 7.35 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 9 V ≤ VIN ≤ 25 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.3 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 60 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 10 V ≤ VIN ≤ 20 V,

IOUT = 50 mA, Tj = 25°C 59 75 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 1.3 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −0.8 ― mV/°C

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7808SB

Electrical Characteristics

(Unless otherwise specified, VIN = 14 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 7.7 8.0 8.3 V

10.5 V ≤ VIN ≤ 25 V ― 6 160

Line regulation Reg·line 1 Tj = 25°C

11 V ≤ VIN ≤ 17 V ― 2 80

5 mA ≤ IOUT ≤ 1.0 A ― 12 160

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 80

Output voltage VOUT 1 Tj = 25°C 10.5 V ≤ VIN ≤ 23 V,

5.0 mA ≤ IOUT ≤ 1.0 A 7.6 ― 8.4 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 10.5 V ≤ VIN ≤ 25 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 70 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 11.5 V ≤ VIN ≤ 21.5 V,

IOUT = 50 mA, Tj = 25°C 58 74 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 1.1 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −1.0 ― mV/°C

TA7809SB

Electrical Characteristics

(Unless otherwise specified, VIN = 15 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 8.64 9.0 9.36 V

11.5 V ≤ VIN ≤ 26 V ― 7 180

Line regulation Reg.line 1 Tj = 25°C

13 V ≤ VIN ≤ 19 V ― 2.5 90

5 mA ≤ IOUT ≤ 1.0 A ― 12 180

Load regulation Reg.load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 90

Output voltage VOUT 1 Tj = 25°C 11.5 V ≤ VIN ≤ 24 V,

5.0 mA ≤ IOUT ≤ 1.0 A 8.55 ― 9.45 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 11.5 V ≤ VIN ≤ 26 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 75 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 12.5 V ≤ VIN ≤ 22.5 V,

IOUT = 50 mA, Tj = 25°C 56 72 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 1.0 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −1.1 ― mV/°C

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7810SB

Electrical Characteristics

(Unless otherwise specified, VIN = 16 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 9.6 10.0 10.4 V

12.5 V ≤ VIN ≤ 27 V ― 8 200

Line regulation Reg·line 1 Tj = 25°C

14 V ≤ VIN ≤ 20 V ― 2.5 100

5 mA ≤ IOUT ≤ 1.0 A ― 12 200

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 100

Output voltage VOUT 1 Tj = 25°C 12.5 V ≤ VIN ≤ 25 V,

5.0 mA ≤ IOUT ≤ 1.0 A 9.5 ― 10.5 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 12.5 V ≤ VIN ≤ 27 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 80 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 13.5 V ≤ VIN ≤ 23.5 V,

IOUT = 50 mA, Tj = 25°C 55 72 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 0.9 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −1.3 ― mV/°C

TA7812SB

Electrical Characteristics

(Unless otherwise specified, VIN = 19 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 11.5 12.0 12.5 V

14.5 V ≤ VIN ≤ 30 V ― 10 240

Line regulation Reg·line 1 Tj = 25°C

16 V ≤ VIN ≤ 22 V ― 3 120

5 mA ≤ IOUT ≤ 1.0 A ― 12 240

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 120

Output voltage VOUT 1 Tj = 25°C 14.5 V ≤ VIN ≤ 27 V,

5.0 mA ≤ IOUT ≤ 1.0 A 11.4 ― 12.6 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.3 8.0 mA

Quiescent current change ΔIB 1 14.5 V ≤ VIN ≤ 30 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 90 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 15 V ≤ VIN ≤ 25 V,

IOUT = 50 mA, Tj = 25°C 55 71 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 0.7 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −1.6 ― mV/°C

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7815SB

Electrical Characteristics

(Unless otherwise specified, VIN = 23 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 14.4 15.0 15.6 V

17.5 V ≤ VIN ≤ 30 V ― 11 300

Line regulation Reg·line 1 Tj = 25°C

20 V ≤ VIN ≤ 26 V ― 3 150

5 mA ≤ IOUT ≤ 1.0 A ― 12 300

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 150

Output voltage VOUT 1 Tj = 25°C 17.5 V ≤ VIN ≤ 30 V,

5.0 mA ≤ IOUT ≤ 1.0 A 14.25 ― 15.75 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.4 8.0 mA

Quiescent current change ΔIB 1 17.5 V ≤ VIN ≤ 30 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 110 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 18.5 V ≤ VIN ≤ 28.5 V,

IOUT = 50 mA, Tj = 25°C 54 70 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 0.5 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −2.0 ― mV/°C

TA7818SB

Electrical Characteristics

(Unless otherwise specified, VIN = 27 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 17.3 18.0 18.7 V

21 V ≤ VIN ≤ 33 V ― 13 360

Line regulation Reg·line 1 Tj = 25°C

24 V ≤ VIN ≤ 30 V ― 4 180

5 mA ≤ IOUT ≤ 1.0 A ― 12 360

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 180

Output voltage VOUT 1 Tj = 25°C 21 V ≤ VIN ≤ 33 V,

5.0 mA ≤ IOUT ≤ 1.0 A 17.1 ― 18.9 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.5 8.0 mA

Quiescent current change ΔIB 1 21 V ≤ VIN ≤ 33 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 125 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 22 V ≤ VIN ≤ 32 V,

IOUT = 50 mA, Tj = 25°C 52 68 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 0.4 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −2.5 ― mV/°C

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7820SB

Electrical Characteristics

(Unless otherwise specified, VIN = 29 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 19.2 20.0 20.8 V

23 V ≤ VIN ≤ 35 V ― 15 400

Line regulation Reg·line 1 Tj = 25°C

26 V ≤ VIN ≤ 32 V ― 5 200

5 mA ≤ IOUT ≤ 1.0 A ― 12 400

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 200

Output voltage VOUT 1 Tj = 25°C 23 V ≤ VIN ≤ 35 V,

5.0 mA ≤ IOUT ≤ 1.0 A 19.0 ― 21.0 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.6 8.0 mA

Quiescent current change ΔIB 1 23 V ≤ VIN ≤ 35 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 135 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 24 V ≤ VIN ≤ 34 V,

IOUT = 50 mA, Tj = 25°C 50 66 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 0.4 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −3.0 ― mV/°C

TA7824SB

Electrical Characteristics

(Unless otherwise specified, VIN = 33 V, IOUT = 500 mA, 0°C ≤ Tj ≤ 125°C)

Characteristics Symbol

Test

Circuit Test Condition Min Typ. Max Unit

Output voltage VOUT 1 Tj = 25°C, IOUT = 100 mA 23.0 24.0 25.0 V

27 V ≤ VIN ≤ 38 V ― 18 480

Line regulation Reg·line 1 Tj = 25°C

30 V ≤ VIN ≤ 36 V ― 6 240

5 mA ≤ IOUT ≤ 1.0 A ― 12 480

Load regulation Reg·load 1 Tj = 25°C

250 mA ≤ IOUT ≤ 750 mA ― 4 240

Output voltage VOUT 1 Tj = 25°C 27 V ≤ VIN ≤ 38 V,

5.0 mA ≤ IOUT ≤ 1.0 A 22.8 ― 25.2 V

Quiescent current IB 1 Tj = 25°C, IOUT = 5 mA ― 4.6 8.0 mA

Quiescent current change ΔIB 1 27 V ≤ VIN ≤ 38 V,

IOUT = 5 mA, Tj = 25°C ― ― 1.0 mA

Output noise voltage VNO 2 Ta = 25°C, 10 Hz ≤ f ≤ 100 kHz,

IOUT = 50 mA ― 150 ― μVrms

Ripple rejection R.R. 3 f = 120 Hz, 28 V ≤ VIN ≤ 38 V,

IOUT = 50 mA, Tj = 25°C 50 66 ― dB

Dropout voltage VD 1 IOUT = 1.0 A, Tj = 25°C ― 2.0 ― V

Short circuit current limit ISC 1 Tj = 25°C ― 0.3 ― A

Average temperature

coefficient of output voltage TCVO 1 IOUT = 5 mA ― −3.5 ― mV/°C

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

Test Circuit 1 / Standard Application Circuit

Test Circuit 2

Test Circuit 3

R.R.

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

Usage Precautions

(1) In regard to GND, be careful not to apply a negative voltage to the input/output terminal.

(2) If a surge voltage exceeding the absolute maximum rating is applied to the input terminal or if a

voltage in excess of the input terminal voltage is applied to the output terminal, the circuit may be

destroyed.

Particular care is necessary in the case of the latter.

Circuit destruction may also occur if the input terminal shorts to GND in a state of normal operation,

causing the output terminal voltage to exceed the input voltage (GND potential) and the electrical

charge of the chemical capacitor connected to the output terminal to flow into the input side.

Where these risks exist, take steps such as connecting zener and general silicon diodes to the circuit,

as shown in the figure below.

(3) When the input voltage is too high, the power dissipation of the three-terminal regulator, which is a

series regulator, increases, causing the junction temperature to rise. In such a case, it is

recommended to reduce the power dissipation, and hence the junction temperature, by inserting a

power-limiting resistor RSD in the input terminal.

The power dissipation PD of the IC is expressed in the following equation.

Reducing VIN' below the lowest voltage necessary for the IC will cause ripple, deterioration in output

regulation and, in certain circumstances, parasitic oscillation.

To determine the resistance value of RSD, design with a margin, referring to the following equation.

(4) Be sure to connect a capacitor near the input terminal and output terminal between both terminals

and GND. The capacitances should be determined experimentally because they depend on PCB

patterns. In particular, adequate investigation should be made to ensure there is no problem even in

high or low temperatures

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

• Low voltage

Do not apply voltage to the Product that is lower than the minimum operating voltage, or the Product’s

protective functions will not operate properly and the Product may be permanently damaged.

• Overcurrent Protection

The overcurrent protection circuits in the Product are designed to temporarily protect Product from minor

overcurrent of brief duration. When the overcurrent protective function in the Product activates,

immediately cease application of overcurrent to Product. Improper usage of Product, such as application of

current to Product exceeding the absolute maximum ratings, could cause the overcurrent protection circuit

not to operate properly and/or damage Product permanently even before the protection circuit starts to

operate.

• Thermal shutdown Protection

The thermal shutdown circuits in the Product are designed to temporarily protect Product from minor

overheating of brief duration. When the overheating protective function in the Product activates,

immediately correct the overheating situation. Improper usage of Product, such as the application of heat

to Product exceeding the absolute maximum ratings, could cause the overheating protection circuit not to

operate properly and/or damage Product permanently even before the protection circuit starts to operate.

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

Package Dimensions

SIP3-P-2.50A Unit: mm

Weight: 1.5 g (typ.)

TA7805,057,06,07,08,09,10,12,15,18,20,24SB

2010-06-21

RESTRICTIONS ON PRODUCT USE

• Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information

in this document, and related hardware, software and systems (collectively “Product”) without notice.

• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with

TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.

• Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are

responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and

systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily

injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the

Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of

all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes

for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the

instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their

own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such

design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,

diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating

parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR

APPLICATIONS.

• Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring

equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.

Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or

reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious

public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used

in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling

equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric

power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this

document.

• Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.

• Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any

applicable laws or regulations.

• The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any

infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to

any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.

• ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE

FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY

WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR

LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND

LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO

SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.

• Do not use or otherwise make available Product or related software or technology for any military purposes, including without

limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile

technology products (mass destruction weapons). Product and related software and technology may be controlled under the

Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product

or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.

• Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.

Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,

including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of

noncompliance with applicable laws and regulations.