(R) DRV1100 DR OPVA1100 658 DRV 110 0 HIGH POWER DIFFERENTIAL DRIVER AMPLIFIER FEATURES DESCRIPTION The DRV1100 is fixed gain differential line driver designed for very low harmonic distortion at the high powers required of xDSL line interface standards. Operating on a single +5V supply, it can deliver 230mA peak output current and 9.5Vp-p differential output voltage swing. This high output power on a single +5V supply makes the DRV1100 an excellent choice for the xDSL applications that require up to 17dBm power onto the line with high crest factors. The DRV1100 is available in both 8-pin plastic DIP and SO-8 packages. HIGH OUTPUT CURRENT: 230mA SINGLE SUPPLY OPERATION: 5V 5MHz BANDWIDTH: 6Vp-p into 15 VERY LOW THD AT HIGH POWER: -72dBc at 6Vp-p, 100kHz, 100 LOW QUIESCENT CURRENT: 11mA FIXED DIFFERENTIAL GAIN: 3V/V APPLICATIONS xDSL TWISTED PAIR LINE DRIVER COMMUNICATIONS LINE DRIVER TRANSFORMER DRIVER SOLENOID DRIVER HIGH POWER AUDIO DRIVER CRT YOKE DRIVER +5V DRV1100 Out+ 4 In+ G = 3V/V In- 4 Out- Patent Pending Protection 135 1:4 Transformer GND International Airport Industrial Park * Mailing Address: PO Box 11400, Tucson, AZ 85734 * Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 * Tel: (520) 746-1111 * Twx: 910-952-1111 Internet: http://www.burr-brown.com/ * FAXLine: (800) 548-6133 (US/Canada Only) * Cable: BBRCORP * Telex: 066-6491 * FAX: (520) 889-1510 * Immediate Product Info: (800) 548-6132 (c) SBWS004 1996 Burr-Brown Corporation PDS-1354 Printed in U.S.A. December, 1996 SPECIFICATIONS At VDD = +5.0V, VCM = VDD/2, TA = 25C, unless otherwise specified. DRV1100P, U PARAMETER CONDITIONS AC PERFORMANCE -3dB Bandwidth Differential Slew Rate Step Response Delay(1) Settling Time to 1%, Step Input Settling Time to 1%, Step Input Settling Time to 0.1%, Step Input Settling Time to 0.1%, Step Input THD, Total Harmonic Distortion(2) f = 10kHz f = 10kHz f = 100kHz f = 100kHz Input Voltage Noise Input Current Noise INPUT CHARACTERISTICS Differential Input Resistance Differential Input Capacitance Common-Mode Input Resistance Common-Mode Input Capacitance Input Offset Voltage Input Bias Current Common-Mode Rejection Ratio Power Supply Rejection Ratio Input Common-Mode Voltage Range(3) OUTPUT CHARACTERISTICS Differential Output Offset, RTO Differential Output Offset Drift, RTO Differential Output Resistance Peak Current (Continuous) Differential Output Voltage Swing Output Voltage Swing, Each Side Gain Gain Error POWER SUPPLY Operating Voltage Range Quiescent Current MIN RL = 15, VO = 1Vp-p RL 100, VO = 1Vp-p RL = 15, VO = 6Vp-p RL 100, VO = 6Vp-p RL = 100, VO = 6Vp-p VO = 1Vp-p VO = 1Vp-p, RL = 100 VO = 6Vp-p, RL = 100 VO = 1Vp-p, RL = 100 VO = 6Vp-p, RL = 100 RL = 100, VO = 6Vp-p RL = 15, VO = 6Vp-p RL = 100, VO = 6Vp-p RL = 15, VO = 6Vp-p f = 100kHz f = 100kHz Input Referred Input Referred -66 60 0.5 -40C to +85C RL = 15 RL = 1k RL = 100 RL = 15 RL = 1k Fixed Gain, Differential 200 8.5 6.0 0.125 MAX +4.5 UNITS 8 11 5 6 80 25 0.25 0.3 0.8 1.1 MHz MHz MHz MHz V/s ns s s s s -85 -76 -72 -65 30 0.5 dBc dBc dBc dBc nV/Hz fA/Hz 1011 1 1011 6 5 1 62 76 pF pF mV pA dB dB V VDD -0.5 10 30 0.16 230 9.6 9.5 6.6 25 0.25 mV V/C mA Vp-p Vp-p Vp-p V V/V dB +5.5 +16 V mA +85 C 4.875 3 VDD = 5.0V TEMPERATURE RANGE Thermal Resistance, JA DRV1100P 8-Pin DIP DRV1100U 8-Pin SO-8 TYP +5.0 +11 -40 100 125 C/W C/W NOTES: (1) Time from 50% point of input step to 50% point of output step. (2) Measurement Bandwidth = 500kHz. (3) Output common-mode voltage follows input common-mode voltage; therefore, if input VCM = VDD/2, then output VCM = VDD/2. The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user's own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant any BURR-BROWN product for use in life support devices and/or systems. (R) DRV1100 2 PIN CONFIGURATIONS ABSOLUTE MAXIMUM RATINGS Analog Inputs: Current .............................................. 100mA, Momentary 10mA, Continuous Voltage ....................................... GND -0.3V to VDD +0.2V Analog Outputs Short Circuit to Ground (+25C) ..................... Momentary Analog Outputs Short Circuit to VDD (+25C) ........................... Momentary VDD to GND .............................................................................. -0.3V to 6V Junction Temperature ................................................................... +150C Storage Temperature Range .......................................... -40C to +125C Lead Temperature (soldering, 3s) ................................................. +260C Power Dissipation .............................. (See Thermal/Analysis Discussion) Top View GND 1 8 Out- In+ 2 7 VDD (+5V) In- 3 6 VDD (+5V) GND 4 5 Out+ PACKAGE/ORDERING INFORMATION +5V 6 In+ In- 7 2 5 3 8 4 PRODUCT PACKAGE PACKAGE DRAWING NUMBER(1) DRV1100P DRV1100U 8-Pin PDIP 8-Lead SO-8 006 182 NOTE: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. Out+ Out- ELECTROSTATIC DISCHARGE SENSITIVITY 1 GND This integrated circuit can be damaged by ESD. Burr-Brown recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. (R) 3 DRV1100 TYPICAL PERFORMANCE CURVES At VDD = +5.0V, VCM = VDD/2, TA = 25C, unless otherwise specified. LARGE SIGNAL FREQUENCY RESPONSE SMALL SIGNAL FREQUENCY RESPONSE RL = 1k 9.5 8.5 RL = 100 7.5 6.5 Differential Gain (dB) Differential Gain (dB) 8.5 RL = 15 5.5 4.5 3.5 7.5 VO = 1Vp-p 10K 5.5 1M RL = 15 4.5 3.5 1.5 100K RL = 100 6.5 2.5 2.5 1.5 RL = 1k 9.5 VO = 6Vp-p 10K 10M Frequency (Hz) SMALL SIGNAL 2ND HARMONIC DISTORTION 10M -40 VO = 1Vp-p VO = 1Vp-p -45 -45 RL = 15 -50 3rd Harmonic (dB) 2nd Harmonic (dB) 1M SMALL SIGNAL 3RD HARMONIC DISTORTION -40 -55 -60 -65 -70 RL = 15 -50 -55 RL = 100 -60 -65 -70 RL = 100 -75 -75 -80 100K 1M -80 100K 10M 1M Frequency (Hz) 10M Frequency (Hz) LARGE SIGNAL 2ND HARMONIC DISTORTION LARGE SIGNAL 3RD HARMONIC DISTORTION -40 -40 VO = 6Vp-p VO = 6Vp-p -45 -45 RL = 15 RL = 15 -50 3rd Harmonic (dB) 2nd Harmonic (dB) 100K Frequency (Hz) -55 -60 RL = 100 -65 -50 -60 -65 -70 -70 -75 -75 -80 100K 1M -80 100K 10M Frequency (Hz) 1M Frequency (Hz) (R) DRV1100 RL = 100 -55 4 10M TYPICAL PERFORMANCE CURVES (CONT) At VDD = +5.0V, VCM = VDD/2, TA = 25C, unless otherwise specified. 100kHz THD -40 -50 -50 RL = 15 THD (dBc) THD (dBc) 10kHz THD -40 -60 -70 RL = 15 -60 RL = 100 -70 RL = 100 -80 -80 RL = 1k RL = 1k -90 -90 1 2 3 4 5 7 8 9 10 1 2 6 SMALL SIGNAL STEP RESPONSE LARGE SIGNAL STEP RESPONSE Output RL = 100 0 -0.5V Input 0 -3V Time (50ns/div) Time (50ns/div) LARGE SIGNAL OPERATING RANGE 10 MAXIMUM VO vs SUPPLY VOLTAGE 12 8 Differential Output Voltage (Vp-p) RL = 1k 1% THD RL = 100 7 6 RL = 15 5 7 8 9 10 RL = 100 +3V Differential Voltage (750mV/div) Input Differential Output Swing (Vp-p) 5 4 Differential Output Voltage (Vp-p) +0.5V 9 3 Differential Output Voltage (Vp-p) Output Differential Voltage (125mV/div) 6 4 3 2 1 0 RL = 1k 10 RL = 100 8 RL = 15 6 4 2 0 1K 10K 100K 1M 10M 4.5 Frequency (Hz) 4.75 5 5.25 5.5 Supply Voltage (VDD) (R) 5 DRV1100 TYPICAL PERFORMANCE CURVES (CONT) At VDD = +5.0V, VCM = VDD/2, TA = 25C, unless otherwise specified. DIFFERENTIAL OUTPUT IMPEDANCE DIFFERENTIAL INPUT VOLTAGE NOISE Impedance () 10 100 1 0.1 10 100 1K 10K 100K 1k 1M 10K 100K 1M 10M Frequency Frequency (Hz) QUIESCENT CURRENT vs TEMPERATURE POWER SUPPLY REJECTION vs FREQUENCY 13 80 12 70 VDD = +5V 11 60 10 PSRR (dB) Quiescent Current (mA) Voltage Noise (nV/Hz) 1000 9 8 7 6 50 40 30 20 5 10 4 0 3 -40 -20 0 20 40 60 80 100 1K Temperature (C) 100K Frequency (Hz) (R) DRV1100 10K 6 1M 10M APPLICATIONS INFORMATION INTERNAL BLOCK DIAGRAM The DRV1100 is a true differential input to differential output fixed gain amplifier. Operating on a single +5V power supply, it provides an internally fixed differential gain of +3 and a common-mode gain of +1 from the input to output. Fabricated on an advanced CMOS process, it offers very high input impedance along with a low impedance 230mA output drive. Figure 1 shows a simplified internal block diagram. Out+ VDD/2 VP Out- VP VDD/2 Load VP 0V VP Out+ FIGURE 2. DRV1100 Single Ended and Differential Output Waveforms. In+ Buffer Preamp (Vp-p). Squaring 1/2 of the Vp-p and dividing by the load will give the peak power. For example, the Typical Performance Curves show that on +5V supply the DRV1100 will deliver 6.8Vp-p into 15 at 500kHz. The peak load power under this condition is (6.8Vp-p/2)2/15 = 770mW. Out- In- FIGURE 1. Simplified DRV1100 Internal Block Diagram. SUPPLY VOLTAGE The DRV1100 is designed for operation on a single +5V supply. For loads > 200, each output will swing rail to rail. This gives a peak-to-peak differential output swing that is approximately = 2 * VDD. For best distortion performance, the power supply should be decoupled to a good ground plane immediately adjacent to the package with a 0.1F capacitor. In addition, a larger electolytic supply decoupling capacitor (6.8F) should be near the package but can be shared among multiple devices. To achieve the maximum dynamic range, operate the DRV1100 with the inputs centered at VDD / 2. This will place the output differential swing centered at VDD /2 for maximum swing and lowest distortion. Purely differential input signals will produce a purely differential output signal. A single ended input signal, applied to one input of the DRV1100, with the other input at a fixed voltage, will produce both a differential and common-mode output signal. This is an acceptable mode of operation when the DRV1100 is driving an element with good common-mode rejection (such as a transformer). DIGITAL SUBSCRIBER LINE APPLICATIONS The DRV1100 is particularly suited to the high power, low distortion, requirements of a twisted pair driver in digital communications applications. These include HDSL (High bit rate Digital Subscriber Lines), ADSL (Asymmetrical Digital Subscriber Lines), and RADSL (Rate adaptive ADSL). Figure 3 shows a typical transformer coupled xDSL line driver configuration. In general, the DRV1100 is usable for output power requirements up to 17dBm with a crest factor up to 6 (crest factor is the ratio of peak to rms voltage). DIFFERENTIAL OUTPUT VOLTAGE AND POWER Applying the balanced differential output voltage of the DRV1100 to a load between the outputs will produce a peakto-peak voltage swing that is twice the swing of each individual output. This is illustrated in Figure 2 where the common-mode voltage is VDD / 2. For a load connected between the outputs, the only voltage that matters is the differential voltage between the two outputs--the commonmode voltage does not produce any load current in this case. To calculate the required amplifier power for an xDSL application-- The peak power that the DRV1100 can deliver into a differential load is VP2/ RL. The Typical Performance Curves show the maximum Vp-p versus load and frequency. The peak voltage (Vp) equals 1/2 of the peak-to-peak voltage * Determine the average power required onto the line in the particular application. The DRV1100 must be able to deliver twice this power (+3dB) to account for the power (R) 7 DRV1100 +5V Protection Circuits DRV1100 Out+ 4 In+ Line Impedance 4 In- 135 Out- 1:4 Transformer GND FIGURE 3. Typical Digital Subscriber Line Application. loss through the series impedance matching resistors shown in Figure 3. Twice the required line power must be delivered by the DRV1100 through the frequency band of interest with the distortion required by the system. ground or to the supply without damage. The outputs are not, however, designed for a continuous short to ground or the supply. * Calculate the RMS voltage required at the output of the DRV1100 with this 2X line power requirement. Vrms = (2 * PLINE * RL)1/2, where RL is the total load impedance that the DRV1100 must drive. Multiply this Vrms by 2 * crest factor to get the total required differential peak-topeak voltage at the output. The DRV1100 must be able to drive the peak-to-peak differential voltage into the load impedance. POWER DISSIPATION AND THERMAL ANALYSIS The total internal power dissipation of the DRV1100 is the sum of a quiescent term and the power dissipated internally to deliver the load power. The Typical Performance Curves show the quiescent current over temperature. At +5V supply, the typical no load supply current of 11mA will dissipate 55mW quiescent power. The rms power dissipated in the output circuit to deliver a Vrms to a load RL is: Where possible, the transformer turns ratio may be adjusted to keep within the DRV1100 output voltage and current constraints for a given RLINE and desired power onto the line. Prms = (VDD - Vrms) * (Vrms/RL) The internal power dissipation will reach a maximum when Vrms is equal to VDD /2. For a sinusoidal output, this corresponds to an output Vp-p = 1.41 * VDD. Using the example of Figure 3, assume the average power desired on a 135 line is 14dBm (HDSL). Twice this power (17dBm) is required into the matching resistors on the primary side of the transformer. This 135 load is reflected through the 1:4 transformer as a (135/(42)) = 8.4 load. The two series 4.1 resistors, along with the 0.2 differential output impedance of the DRV1100, will provide impedance matching into this 8.4 load. The DRV1100 will see approximately a 16.5 load under these conditions. The required 17dBm (50mW) into this load will need an output Vrms = (50mW * 16.5)1/2 = 0.91Vrms. Assuming a crest factor of 3, the differential peak-to-peak output voltage = 6 * 0.91 = 5.45Vp-p. The Typical Performance Curves show that, at 100kHz, the DRV1100 can deliver this voltage swing with less than -62dB THD. As an example, compute the power and junction temperature under a worst case condition with VDD = +5V and Vrms = 2.5V into a 16 differential load (peak output current for a sinusoid would be 222mA). The total internal power dissipation would be: (5V * 11mA) + (5V - 2.5V) * (2.5V/16) = 446mW To compute the internal junctions temperature, this power is multiplied by the junction to ambient thermal impedance (to get the temperature rise above ambient) then added to the ambient temperature. Using the specified maximum ambient temperature of +85C, the junction temperature for the DRV1100 in an SO-8 package under these worst case conditions will be: OUTPUT PROTECTION Figure 3 also shows overvoltage and short circuit protection elements that are commonly included in xDSL applications. Overvoltage suppressors include diodes or MOV's. The outputs of the DRV1100 can be momentarily shorted to TJ = 85C + 0.446W * 125C/W = 141C (R) DRV1100 8 Often, the RB resistors will be set to a relatively high value (> 10k) to minimize quiescent current in the reference path. If a lower input impedance is desired, additional terminating resistors may be added to the input side of the blocking capacitors (CB). INTERNAL TEMPERATURE RISE OF DRV1100 IN SOIC 90 80 Limit at 85C Ambient Temperature Rise 70 The circuit of Figure 5 may also be operated with only a single ended input. In that case, the reference voltage on the other input should be decoupled to ground with a 0.1F capacitor. In this connection, the input will generate unbalanced outputs. The differential output voltage will still be 3 times the input peak-to-peak voltage, but since there is now a common-mode voltage input, there will be a common mode voltage output. The output common-mode voltage will be equal to the input signal's peak-to-peak swing. This common-mode component will reduce the available differential output voltage swing. However, if the output load has good common-mode rejection, such as a transformer, this is an acceptable way of using the DRV1100 with a single ended source. 60 50 RL = 15 40 30 20 RL = 100 10 0 0 0.5 1 2 1.5 2.5 3 3.5 Load Voltage (rms) FIGURE 4. Junction Temperature Rise From Ambient for the DRV1100U. The internal junction temperature should, in all cases, be limited to < 150C. For a maximum ambient temperature of +85C, this limits the internal temperature rise to less than 65C. Figure 4 shows the temperature rise from ambient to junction for loads of 15 and 100. This shows that the internal junction temperature will never exceed the rated maximum for a 15 load. Figure 6 shows a means of translating a ground centered single ended input to a purely differential signal for application to DRV1100 input. This circuit uses a wideband dual op amp in cross coupled feedback configuration. The outputs of this circuit may then be fed into the inputs of Figure 5. The total gain of Figure 6 is 2 * (RF / RG ). The circuit will act to hold all 4 op amp inputs equal to the + input of the lower op amp. Since this is at ground, the midpoint for the input signal (where the two outputs will be equal) is also at 0V. INPUT INTERFACE CIRCUITS Best performance with the DRV1100 is achieved with a differential input centered at VDD /2. Signals that do not require DC coupling may be connected as shown in Figure 5 through blocking caps to a midpoint reference developed through resistor dividers from the supply voltage. The value for the RB resistors determine four performance requirements. RF RG VI * They bias the inputs at the supply midpoint. * They provide a DC bias current path for the input to the DRV1100 1/2 OPA2650 * They set the AC input impedance for the source signals to RB/2. 500 * They set the low frequency cutoff frequency along with CB. 500 + RF V RG I - RF V RG I 500 500 +VDD 1/2 OPA2650 RB CB V1 RB RB DRV1100 RL FIGURE 6. Single Ended to Differential Conversion. V2 CB RB FIGURE 5. AC Coupled Differential Input Interface. (R) 9 DRV1100 PACKAGE OPTION ADDENDUM www.ti.com 11-Nov-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty DRV1100U NRND SOIC D 8 DRV1100U/2K5 NRND SOIC D DRV1100U/2K5G4 NRND SOIC DRV1100UG4 NRND SOIC 75 Lead/Ball Finish MSL Peak Temp (3) Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR D 8 CU NIPDAU Level-2-260C-1 YEAR 75 Green (RoHS & no Sb/Br) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device DRV1100U/2K5 Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel Diameter Width (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 6.4 5.2 2.1 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DRV1100U/2K5 SOIC D 8 2500 346.0 346.0 29.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2008, Texas Instruments Incorporated