FMP16.48 Rectifier Module Data Sheet Description The Power-One FMP16.48 rectifier provides extremely reliable DC power in the highest possible density. This rectifier module incorporates the latest in power monitoring solutions using an internal microprocessor that gives up-to-the-second updates to the system controller and adjacent rectifiers. This guarantees tightly controlled load sharing among rectifiers and provides status and identification information to the controller. At only four rack units high, these compact rectifiers provide up to 1600 watts and allow up to 10 rectifier modules in a 23-inch subrack or eight modules in a 19-inch subrack. Designed with diversity in mind, the FMP16.48 rectifier is able to operate in a complete range of indoor and outdoor applications. Features 23-inch PPR16 Subrack MCD10086 Rev. 1.1, 2-Oct-08 Page 1 of 2 * RoHS lead free solder and lead solder exempted products are available * Compact 4-rack unit height * 717 W/L (11.75 W/in) * 205/240 VAC single-phase input * Input overvoltage disconnection * Thermal protection * Hot-swappable * No adjustments required * 93,5% typical efficiency * Active and droop current sharing * International standards compliance www.power-one.com FMP16.48 Rectifier Module Data Sheet Input Mechanical Model FMP16.48 Input Voltage 100-240 VAC 15% single phase (44-66 Hz) (185-85 V at derated output power) Current (max.) <10 A Soft Start <13A /1ms Harmonics EN 61000-3-2 (Power factor > 0.98 typical) Dimensions (WxHxD) 51 x 177 x 280 mm (2.0 x 6.97 x 11.02 in) Weight 2.2 kg (4.85 lb) Cooling Fan-cooled, speed-controlled, and alarmed Insulation Reinforced insulation, tested at: 4.25 kVDC primary-secondary 2.12 kVDC primary-ground 0.75 kVDC secondary-ground Enclosure IP20 Mounting 19in/ 4U subrack up to 8 modules 23in/ 4U subrack up to 10 modules Surge Immunity EN 61000-4-5 Fuse 2 x F 12.5A (line & neutral) Connection FCI 51939-066 Other Technical Data EMC EN 61000-6-2, EN 61000-6-3, FCC Part 15 Class B Safety EN 60950-1 UL 60950-1, IEC60950-1, and CSA C22.2 No. 60950-1 Protection Short circuit proof, automatic current limiting, selective shutdown of modules at excessive output voltage. Thermal protection reduces the output power at environmental temperatures above maximum level. Shut down at >75 C with an automatic restart. Input overvoltage disconnecting at >275 VAC with automatic reset at >260 VAC. Alarms High output voltage/ shutdown, Low voltage/ module failure. Each alarm has an LED indicator on the front panel. Indications Green LED Power ON Yellow LED Current limit/ thermal protection. Com. failure (flashing) Red LED Module failure/ high output voltage/ shutdown Output Model FMP16.48 Output Voltage 45-57 VDC Power (max.) 1600 W @ 45-57 VDC (input >185 VAC) 675 W @ 45-57 VDC (input 185 - 85 VAC) Current (max.) 32 A Efficiency (at 40-90% load) >93%, typical 93.5% Tolerance Vout 1.0% Transient Response 5% at load variation 10-90% or 90-10% recovery time 50 ms Load Sharing <5% of nominal current Ripple <100 mV p-p (BW 30 MHz) Psophometric <2 mV, according to CCITT norms Audible Noise <60dBA Connection FCI 51939-066 EMC EN 61000-6-2, EN 61000-6-4 Operating Temperature -40 to +65 C up to 2000 m -40 to +55 C above 2000 m Storage Temperature -60 to +85 C Radiated EMC EN 61000-6-2, EN 61000-6-3, FCC Part 15, Class B Environment Storage: Transport: Operation: Earthquake: NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. MCD10086 Rev. 1.1, 2-Oct-08 Page 2 of 2 ETS 300 019-2-1 ETS 300 019-2-2 ETS 300 019-2-3 GR 63 Core Zone 4 www.power-one.com