CA-3083 Data Sheet December 15, 2011 General Purpose High Current NPN Transistor Array Features * High IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA (Max) The CA3083 is a versatile array of five high current (to 100mA) NPN transistors on a common monolithic substrate. In addition, two of these transistors (Q1 and Q2) are matched at low current (i.e., 1mA) for applications in which offset parameters are of special importance. Independent connections for each transistor plus a separate terminal for the substrate permit maximum flexibility in circuit design. Ordering Information PART NUMBER TEMP. RANGE PART (C) MARKING FN481.7 * Low VCE sat (at 50mA). . . . . . . . . . . . . . . . . . . 0.7V (Max) * Matched Pair (Q1 and Q2) - VIO (VBE Match) . . . . . . . . . . . . . . . . . . . . . 5mV (Max) - IIO (at 1mA) . . . . . . . . . . . . . . . . . . . . . . . . 2.5A (Max) * 5 Independent Transistors Plus Separate Substrate Connection * Pb-Free Plus Anneal Available (RoHS Compliant) Applications PACKAGE PKG. DWG. # * Signal Processing and Switching Systems Operating from DC to VHF E16.3 * Lamp and Relay Driver CA3083 CA3083 -55 to 125 16 Ld PDIP CA3083Z (Note) CA3083Z -55 to 125 16 Ld PDIP* (Pb-free) E16.3 CA3083M96 3083 -55 to 125 16 Ld SOIC Tape and Reel CA3083MZ (Note) 3083MZ -55 to 125 16 Ld SOIC (Pb-Free) M16.15 CA3083MZ96 3083MZ (Note) -55 to 125 16 Ld SOIC (Pb-Free) M16.15 Tape and Reel M16.15 *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. * Differential Amplifier * Temperature Compensated Amplifier * Thyristor Firing * See Application Note AN5296 "Applications of the CA3018 Circuit Transistor Array" for Suggested Applications Pinout CA3083 (PDIP, SOIC) TOP VIEW NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. 16 1 2 3 15 Q1 14 Q2 13 4 SUBSTRATE Q5 5 12 11 6 Q3 7 8 1 Q4 10 9 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 | Copyright Intersil Americas Inc. 1998, 2005, 2006, 2011. All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners. CA-3083 Absolute Maximum Ratings Thermal Information The following ratings apply for each transistor in the device: Collector-to-Emitter Voltage, VCEO . . . . . . . . . . . . . . . . . . . . . . 15V Collector-to-Base Voltage, VCBO . . . . . . . . . . . . . . . . . . . . . . . . 20V Collector-to-Substrate Voltage, VCIO (Note 1). . . . . . . . . . . . . . 20V Emitter-to-Base Voltage, VEBO . . . . . . . . . . . . . . . . . . . . . . . . . . 5V Collector Current (IC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mA Base Current (IB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20mA Thermal Resistance (Typical, Note 2) JA (C/W) JC (C/W) PDIP Package . . . . . . . . . . . . . . . . . . . 135 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 200 N/A Maximum Power Dissipation (Any One Transistor) . . . . . . . 500mW Maximum Junction Temperature (Plastic Package) . . . . . . . 150C Maximum Storage Temperature Range . . . . . . . . . . -65C to 150C Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . 300C (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . . .-55C to 125C CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. The collector of each transistor of the CA3083 is isolated from the substrate by an integral diode. The substrate must be connected to a voltage which is more negative than any collector voltage in order to maintain isolation between transistors and provide normal transistor action. To avoid undesired coupling between transistors, the substrate Terminal (5) should be maintained at either DC or signal (AC) ground. A suitable bypass capacitor can be used to establish a signal ground. 2. JA is measured with the component mounted on an evaluation PC board in free air. Electrical Specifications For Equipment Design, TA = 25C PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNITS FOR EACH TRANSISTOR Collector-to-Base Breakdown Voltage V(BR)CBO IC = 100A, IE = 0 20 60 - V Collector-to-Emitter Breakdown Voltage V(BR)CEO IC = 1mA, IB = 0 15 24 - V Collector-to-Substrate Breakdown Voltage V(BR)CIO ICI = 100A, IB = 0, IE = 0 20 60 - V Emitter-to-Base Breakdown Voltage V(BR)EBO IE = 500A, IC = 0 5 6.9 - V Collector-Cutoff-Current ICEO VCE = 10V, IB = 0 - - 10 A Collector-Cutoff-Current ICBO VCB = 10V, IE = 0 - - 1 A DC Forward-Current Transfer Ratio (Note 3) (Figure 1) hFE VCE = 3V IC = 10mA 40 76 - IC = 50mA 40 75 - Base-to-Emitter Voltage (Figure 2) VBE VCE = 3V, IC = 10mA 0.65 0.74 0.85 V VCE SAT IC = 50mA, IB = 5mA - 0.40 0.70 V fT VCE = 3V, IC = 10mA - 450 - MHz Absolute Input Offset Voltage (Figure 6) |VIO| VCE = 3V, IC = 1mA - 1.2 5 mV Absolute Input Offset Current (Figure 7) |IIO| VCE = 3V, IC = 1mA - 0.7 2.5 A Collector-to-Emitter Saturation Voltage (Figures 3, 4) Gain Bandwidth Product FOR TRANSISTORS Q1 AND Q2 (As a Differential Amplifier) NOTE: 3. Actual forcing current is via the emitter for this test. 2 FN481.7 December 15, 2011 CA-3083 100 0.9 VCE = 3V VCE = 3V 90 BASE-TO-EMITTER VOLTAGE (V) DC FORWARD CURRENT TRANSFER RATIO Typical Performance Curves TA = 70C TA = 25C 80 TA = 0C 70 60 1 10 TA = 0C TA = 25C 0.7 TA = 70C 0.6 0.5 0.1 50 0.1 0.8 100 COLLECTOR CURRENT (mA) FIGURE 1. hFE vs IC 1.2 hFE = 10, TA = 25oC hFE = 10, TA = 70C 0.8 0.6 0.4 MAXIMUM 0.2 1 0.8 0.6 0.4 0 1 10 1 FIGURE 3. VCE SAT vs IC ABSOLUTE INPUT OFFSET VOLTAGE (mV) BASE-TO-EMITTER SATURATION VOLTAGE (V) hFE = 10, TA = 25C 0.9 0.8 0.7 0.6 0.5 3 10 COLLECTOR CURRENT (mA) 100 FIGURE 4. VCE SAT vs IC 1 FIGURE 5. VBE SAT vs IC TYPICAL 0 100 COLLECTOR CURRENT (mA) 10 COLLECTOR CURRENT (mA) MAXIMUM 0.2 TYPICAL 1 100 FIGURE 2. VBE vs IC COLLECTOR-TO-EMITTER SATURATION VOLTAGE (V) COLLECTOR-TO-EMITTER SATURATION VOLTAGE (V) 1 1 10 COLLECTOR CURRENT (mA) 100 6 VCE = 3V, TA = 25C 5 4 3 2 1 0 0.1 1 COLLECTOR CURRENT (mA) 10 FIGURE 6. VIO vs IC (TRANSISTORS Q1 AND Q2 AS A DIFFERENTIAL AMPLIFIER) FN481.7 December 15, 2011 CA-3083 ABSOLUTE INPUT OFFSET CURRENT (A) Typical Performance Curves (Continued) 10 VCE = 3V, TA = 25C 1 0.1 0.1 1 COLLECTOR CURRENT (mA) 10 FIGURE 7. IIO vs IC (TRANSISTORS Q1 AND Q2 AS A DIFFERENTIAL AMPLIFIER) All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 4 FN481.7 December 15, 2011