MC33501, MC33503 1.0 V, Rail-to-Rail, Single Operational Amplifiers The MC33501/503 operational amplifier provides rail-to-rail operation on both the input and output. The output can swing within 50 mV of each rail. This rail-to-rail operation enables the user to make full use of the entire supply voltage range available. It is designed to work at very low supply voltages (1.0 V and ground), yet can operate with a supply of up to 7.0 V and ground. Output current boosting techniques provide high output current capability while keeping the drain current of the amplifier to a minimum. Features * Low Voltage, Single Supply Operation (1.0 V and Ground to 7.0 V * * * * * * * * * * * * and Ground) High Input Impedance: Typically 40 fA Input Bias Current Typical Unity Gain Bandwidth @ 5.0 V = 4.0 MHz, @ 1.0 V = 3.0 MHz High Output Current (ISC = 40 mA @ 5.0 V, 13 mA @ 1.0 V) Output Voltage Swings within 50 mV of Both Rails @ 1.0 V Input Voltage Range Includes Both Supply Rails High Voltage Gain: 100 dB Typical @ 1.0 V No Phase Reversal on the Output for Over-Driven Input Signals Typical Input Offset of 0.5 mV Low Supply Current (ID = 1.2 mA/per Amplifier, Typical) 600 W Drive Capability Extended Operating Temperature Range (-40 to 105C) Pb-Free Packages are Available http://onsemi.com MARKING DIAGRAM 5 SOT23-5 SN SUFFIX CASE 483 5 1 xxx AYWG G 1 xxx = AAA; MC33501 AAB; MC33503 A = Assembly Location Y = Year WW = Work Week G = Pb-Free Package (Note: Microdot may be in either location) PIN CONNECTIONS MC33501 5 Output 1 VCC 2 Non-Inverting Input VEE + - 4 Inverting Input 3 (Top View) Applications * * * * * * * * * MC33503 Single Cell NiCd/Ni MH Powered Systems Interface to DSP Portable Communication Devices Low Voltage Active Filters Telephone Circuits Instrumentation Amplifiers Audio Applications Power Supply Monitor and Control Transistor Count: 98 5 Output 1 VEE 2 Non-Inverting Input VCC + - 4 Inverting Input 3 (Top View) ORDERING INFORMATION Device Package Shipping MC33501SNT1 SOT23-5 3000 Tape & Reel MC33501SNT1G SOT23-5 (Pb-Free) 3000 Tape & Reel MC33503SNT1 SOT23-5 3000 Tape & Reel MC33503SNT1G SOT23-5 (Pb-Free) 3000 Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. (c) Semiconductor Components Industries, LLC, 2006 July, 2006 - Rev. 10 1 Publication Order Number: MC33501/D MC33501, MC33503 Base Current Boost Inputs Input Stage Offset Voltage Trim Buffer with 0 V Level Shift Saturation Detector Output Stage Outputs Base Current Boost This device contains 98 active transistors per amplifier. Figure 1. Simplified Block Diagram MAXIMUM RATINGS AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAA AAAAAAA AAAAAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Rating Symbol Supply Voltage (VCC to VEE) ESD Protection Voltage at any Pin Human Body Model Value Unit VS 7.0 V VESD 2000 V Voltage at Any Device Pin VDP VS 0.3 V Input Differential Voltage Range VIDR VCC to VEE V Common Mode Input Voltage Range VCM VCC to VEE V Output Short Circuit Duration tS Note 1 s Maximum Junction Temperature TJ 150 C Storage Temperature Range Tstg -65 to 150 C Maximum Power Dissipation PD Note 1 mW Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. Power dissipation must be considered to ensure maximum junction temperature (TJ) is not exceeded. 2. ESD data available upon request. http://onsemi.com 2 MC33501, MC33503 DC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VCM = VO = VCC/2, RL to VCC/2, TA = 25C, unless otherwise noted.) AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Characteristic Symbol Input Offset Voltage (VCM = 0 to VCC) VCC = 1.0 V TA = 25C TA = -40 to 105C VCC = 3.0 V TA = 25C TA = -40 to 105C VCC = 5.0 V TA = 25C TA = -40 to 105C Min Typ Max VIO Unit mV -5.0 -7.0 0.5 - 5.0 7.0 -5.0 -7.0 0.5 - 5.0 7.0 -5.0 -7.0 0.5 - 5.0 7.0 DVIO/DT - 8.0 - mV/C Input Bias Current (VCC = 1.0 to 5.0 V) I IIB I - 0.00004 1.0 nA Common Mode Input Voltage Range VICR VEE - VCC V Large Signal Voltage Gain VCC = 1.0 V (TA = 25C) RL = 10 kW RL = 1.0 kW VCC = 3.0 V (TA = 25C) RL = 10 kW RL = 1.0 kW VCC = 5.0 V (TA = 25C) RL = 10 kW RL = 1.0 kW AVOL Output Voltage Swing, High (VID = 0.2 V) VCC = 1.0 V (TA = 25C) RL = 10 kW RL = 600 W VCC = 1.0 V (TA = -40 to 105C) RL = 10 kW RL = 600 W VCC = 3.0 V (TA = 25C) RL = 10 kW RL = 600 W VCC = 3.0 V (TA = -40 to 105C) RL = 10 kW RL = 600 W VCC = 5.0 V (TA = 25C) RL = 10 kW RL = 600 W VCC = 5.0 V (TA = -40 to 105C) RL = 10 kW RL = 600 W VOH AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Input Offset Voltage Temperature Coefficient (RS = 50 W) TA = -40 to 105C kV/V 25 5.0 100 50 - - 50 25 500 100 - - 50 25 500 200 - - AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA http://onsemi.com 3 V 0.9 0.85 0.95 0.88 - - 0.85 0.8 - - - - 2.9 2.8 2.93 2.84 - - 2.85 2.75 - - - - 4.9 4.75 4.92 4.81 - - 4.85 4.7 - - - - MC33501, MC33503 DC ELECTRICAL CHARACTERISTICS (continued) (VCC = 5.0 V, VEE = 0 V, VCM = VO = VCC/2, RL to VCC/2, TA = 25C, unless otherwise noted.) AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Characteristic Symbol Output Voltage Swing, Low (VID = 0.2 V) VCC = 1.0 V (TA = 25C) RL = 10 kW RL = 600 W VCC = 1.0 V (TA = -40 to 105C) RL = 10 kW RL = 600 W VCC = 3.0 V (TA = 25C) RL = 10 kW RL = 600 W VCC = 3.0 V (TA = -40 to 105C) RL = 10 kW RL = 600 W VCC = 5.0 V (TA = 25C) RL = 10 kW RL = 600 W VCC = 5.0 V (TA = -40 to 105C) RL = 10 kW RL = 600 W VOL Common Mode Rejection (Vin = 0 to 5.0 V) Power Supply Rejection VCC/VEE = 5.0 V/Ground to 3.0 V/Ground Min Typ Max Unit V 0.05 0.1 0.02 0.05 - - 0.1 0.15 - - - - 0.05 0.1 0.02 0.08 - - 0.1 0.15 - - - - 0.05 0.15 0.02 0.1 - - 0.1 0.2 - - - - CMR 60 75 - dB PSR 60 75 - dB AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Output Short Circuit Current (Vin Diff = 1.0 V) VCC = 1.0 V Source Sink VCC = 3.0 V Source Sink VCC = 5.0 V Source Sink ISC Power Supply Current (Per Amplifier, VO = 0 V) VCC = 1.0 V VCC = 3.0 V VCC = 5.0 V VCC = 1.0 V (TA = -40 to 105C) VCC = 3.0 V (TA = -40 to 105C) VCC = 5.0 V (TA = -40 to 105C) ID mA 6.0 10 13 13 26 26 15 40 32 64 60 140 20 40 40 70 140 140 - - - - - - 1.2 1.5 1.65 - - - 1.75 2.0 2.25 2.0 2.25 2.5 AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA http://onsemi.com 4 mA MC33501, MC33503 AC ELECTRICAL CHARACTERISTICS (VCC = 5.0 V, VEE = 0 V, VCM = VO = VCC/2, TA = 25C, unless otherwise noted.) AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Characteristic Symbol Slew Rate (VS = 2.5 V, VO = -2.0 to 2.0 V, RL = 2.0 kW, AV = 1.0) Positive Slope Negative Slope Min Typ Max 1.8 1.8 3.0 3.0 6.0 6.0 2.0 2.5 3.0 3.0 3.5 4.0 6.0 7.0 8.0 SR Gain Bandwidth Product (f = 100 kHz) VCC = 0.5 V, VEE = -0.5 V VCC = 1.5 V, VEE = -1.5 V VCC = 2.5 V, VEE = -2.5 V Unit V/ms GBW MHz AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAA AAAAA AAAA AAAA AAAA AAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA Gain Margin (RL =10 kW, CL = 0 pF) Am - 6.5 - dB Phase Margin (RL = 10 kW, CL = 0 pF) fm - 60 - Deg Channel Separation (f = 1.0 Hz to 20 kHz, RL = 600 W) CS - 120 - dB Power Bandwidth (VO = 4.0 Vpp, RL = 1.0 kW, THD 1.0%) BWP - 200 - kHz Total Harmonic Distortion (VO = 4.5 Vpp, RL = 600 W, AV = 1.0) f = 1.0 kHz f = 10 kHz THD - - 0.004 0.01 - - % Differential Input Resistance (VCM = 0 V) Rin - >1.0 - terraW Differential Input Capacitance (VCM = 0 V) Cin - 2.0 - pF Equivalent Input Noise Voltage (VCC = 1.0 V, VCM = 0 V, VEE = GND, RS = 100 W) f = 1.0 kHz en nV/Hz - 30 - VCC IN- IN+ Offset Voltage Trim VCC VCC VCC Output Voltage Saturation Detector Body Bias Figure 2. Representative Block Diagram http://onsemi.com 5 Clamp Out MC33501, MC33503 Output Stage General Information The MC33501/503 dual operational amplifier is unique in its ability to provide 1.0 V rail-to-rail performance on both the input and output by using a SMARTMOSt process. The amplifier output swings within 50 mV of both rails and is able to provide 50 mA of output drive current with a 5.0 V supply, and 10 mA with a 1.0 V supply. A 5.0 MHz bandwidth and a slew rate of 3.0 V/ms is achieved with high speed depletion mode NMOS (DNMOS) and vertical PNP transistors. This device is characterized over a temperature range of -40C to 105C. An additional feature of this device is an "on demand" base current cancellation amplifier. This feature provides base drive to the output power devices by making use of a buffer amplifier to perform a voltage-to-current conversion. This is done in direct proportion to the load conditions. This "on demand" feature allows these amplifiers to consume only a few micro-amps of current when the output stage is in its quiescent mode. Yet it provides high output current when required by the load. The rail-to-rail output stage current boost circuit provides 50 mA of output current with a 5.0 V supply (For a 1.0 V supply output stage will do 10 mA) enabling the operational amplifier to drive a 600 W load. A buffer is necessary to isolate the load current effects in the output stage from the input stage. Because of the low voltage conditions, a DNMOS follower is used to provide an essentially zero voltage level shift. This buffer isolates any load current changes on the output stage from loading the input stage. A high speed vertical PNP transistor provides excellent frequency performance while sourcing current. The operational amplifier is also internally compensated to provide a phase margin of 60 degrees. It has a unity gain of 5.0 MHz with a 5.0 V supply and 4.0 MHz with a 1.0 V supply. Circuit Information Input Stage One volt rail-to-rail performance is achieved in the MC33501/503 at the input by using a single pair of depletion mode NMOS devices (DNMOS) to form a differential amplifier with a very low input current of 40 fA. The normal input common mode range of a DNMOS device, with an ion implanted negative threshold, includes ground and relies on the body effect to dynamically shift the threshold to a positive value as the gates are moved from ground towards the positive supply. Because the device is manufactured in a p-well process, the body effect coefficient is sufficiently large to ensure that the input stage will remain substantially saturated when the inputs are at the positive rail. This also applies at very low supply voltages. The 1.0 V rail-to-rail input stage consists of a DNMOS differential amplifier, a folded cascode, and a low voltage balanced mirror. The low voltage cascaded balanced mirror provides high 1st stage gain and base current cancellation without sacrificing signal integrity. A common mode feedback path is also employed to enable the offset voltage to track over the input common mode voltage. The total operational amplifier quiescent current drop is 1.3 mA/amp. Low Voltage Operation The MC33501/503 will operate at supply voltages from 0.9 to 7.0 V and ground. When using the MC33501/503 at supply voltages of less than 1.2 V, input offset voltage may increase slightly as the input signal swings within approximately 50 mV of the positive supply rail. This effect occurs only for supply voltages below 1.2 V, due to the input depletion mode MOSFETs starting to transition between the saturated to linear region, and should be considered when designing high side dc sensing applications operating at the positive supply rail. Since the device is rail-to-rail on both input and output, high dynamic range single battery cell applications are now possible. http://onsemi.com 6 MC33501, MC33503 0 0 TA = -55C 400 600 600 VCC = 5.0 V VEE = 0 V RL to VCC/2 400 200 1.0 k 10 k VEE 100 k 1.0 M Source Saturation -1.0 0.5 0 0 4.0 TA = 125C TA = -55C 8.0 VEE 12 16 20 24 IO, OUTPUT CURRENT (mA) Figure 4. Drive Output Source/Sink Saturation Voltage versus Load Current Figure 3. Output Saturation versus Load Resistance 1000 100 0 100 Gain 80 Phase AVOL, GAIN (dB) 10 1.0 0.1 0.01 0.001 25 50 75 100 Phase Margin = 60 90 40 135 VCC = 2.5 V VEE = -2.5 V RL = 10 k 0 1.0 125 45 60 20 10 100 180 1.0 k 10 k 100 k 1.0 M 10 M TA, AMBIENT TEMPERATURE (C) f, FREQUENCY (Hz) Figure 5. Input Current versus Temperature Figure 6. Gain and Phase versus Frequency 1.0 V/DIV (mV) VCC = 0.5 V VEE = -0.5 V ACL = 1.0 CL = 10 pF RL = 10 k TA = 25C 20 mV/DIV IIB, INPUT CURRENT (pA) TA = 25C VCC - VEE = 5.0 V RL, LOAD RESISTANCE (W) 0 TA = 25C Sink Saturation 1.0 10 M TA = 125C VCC = 2.5 V VEE = -2.5 V ACL = 1.0 CL = 10 pF RL = 600 W TA = 25C t, TIME (500 ms/DIV) t, TIME (1.0 ms/DIV) Figure 7. Transient Response Figure 8. Slew Rate http://onsemi.com 7 m, EXCESS PHASE (DEGREES) 0 100 VCC -0.5 VCC Vsat, OUTPUT SATURATION VOLTAGE (V) Vsat, OUTPUT SATURATION VOLTAGE (mV) 200 120 1600 1400 AVOL , OPEN LOOP GAIN (dB) PDmax, MAXIMUM POWER DISSIPATION (mW) MC33501, MC33503 1200 SO-8 Pkg 1000 DIP Pkg 800 600 400 200 0 -55 -25 0 25 50 75 100 110 100 90 80 70 60 VCC = 2.5 V VEE = -2.5 V RL = 600 W 50 40 30 20 -55 125 -25 TA, AMBIENT TEMPERATURE (C) Figure 9. Maximum Power Dissipation versus Temperature CMR, COMMON MODE REJECTION (dB) VO, OUTPUT VOLTAGE (Vpp) 6.0 5.0 4.0 1.0 0 10 VCC = 2.5 V VEE = -2.5 V AV = 1.0 RL = 600 W TA = 25C 100 1.0 k 10 k 100 k 40 VCC = 2.5 V VEE = -2.5 V TA = 25C 20 100 IISCI, OUTPUT SHORT CIRCUIT CURRENT (mA) PSR, POWER SUPPLY REJECTION (dB) 80 VCC = 0.5 V VEE = -0.5 V Either VCC or VEE TA = 25C 0 100 1.0 k 10 k 100 k 1.0 M Figure 12. Common Mode Rejection versus Frequency VCC = 2.5 V VEE = -2.5 V 100 1.0 k f, FREQUENCY (Hz) 120 10 125 60 0 10 1.0 M 140 20 100 80 Figure 11. Output Voltage versus Frequency 40 75 100 f, FREQUENCY (Hz) 60 50 120 7.0 2.0 25 Figure 10. Open Loop Voltage Gain versus Temperature 8.0 3.0 0 TA, AMBIENT TEMPERATURE (C) 10 k 100 k 100 VCC = 2.5 V VEE = -2.5 V TA = 25C 80 Sink 60 40 Source 20 0 0 f, FREQUENCY (Hz) 0.5 1.0 1.5 2.0 |VS| - |VO| (V) Figure 13. Power Supply Rejection versus Frequency Figure 14. Output Short Circuit Current versus Output Voltage http://onsemi.com 8 2.5 ICC, SUPPLY CURRENT PER AMPLIFIER (mA) IISCI, OUTPUT SHORT CIRCUIT CURRENT (mA) MC33501, MC33503 100 Sink 80 60 VCC = 2.5 V VEE = -2.5 V 40 20 Source 0 -55 -25 0 25 50 75 100 2.5 2.0 1.5 TA = 125C 1.0 TA = 25C 0.5 0 125 0 0.5 Figure 15. Output Short Circuit Current versus Temperature 2.5 PERCENTAGE OF AMPLIFIERS (%) 50 VCC = 3.0 V VO = 1.5 V VEE = 0 V 60 Amplifiers Tested from 2 Wafer Lots 40 30 20 10 0 -50 -40 -30 -20 -10 0 10 20 30 40 40 30 VCC = 3.0 V VO = 1.5 V VEE = 0 V TA = 25C 60 Amplifiers Tested from 2 Wafer Lots 20 10 0 -5.0 -4.0 -3.0 -2.0 50 Figure 17. Input Offset Voltage Temperature Coefficient Distribution THD, TOTAL HARMONIC DISTORTION (%) AV = 1000 AV = 100 AV = 10 0.1 AV = 1.0 0.01 Vout = 0.5 Vpp RL = 600 W 10 100 VCC - VEE = 1.0 V 1.0 k 10 k 0 1.0 2.0 3.0 4.0 5.0 Figure 18. Input Offset Voltage Distribution 10 1.0 -1.0 INPUT OFFSET VOLTAGE (mV) TCVIO, INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT (mV/C) THD, TOTAL HARMONIC DISTORTION (%) 2.0 Figure 16. Supply Current per Amplifier versus Supply Voltage with No Load 50 0.001 1.5 VCC, |VEE|, SUPPLY VOLTAGE (V) TA, AMBIENT TEMPERATURE (C) PERCENTAGE OF AMPLIFIERS (%) 1.0 TA = -55C 100 k 10 Vout = 4.0 Vpp RL = 600 W 1.0 AV = 1000 AV = 100 0.1 AV = 10 0.01 AV = 1.0 0.001 10 100 VCC - VEE = 5.0 V 1.0 k 10 k f, FREQUENCY (Hz) f, FREQUENCY (Hz) Figure 19. Total Harmonic Distortion versus Frequency with 1.0 V Supply Figure 20. Total Harmonic Distortion versus Frequency with 5.0 V Supply http://onsemi.com 9 100 k MC33501, MC33503 3.0 VCC - VEE = 5.0 V - Slew Rate 2.0 VCC - VEE = 1.0 V - Slew Rate 1.0 0 -55 -25 0 25 50 75 100 3.0 2.0 VCC - VEE = 5.0 V f = 100 kHz 1.0 0 -55 -25 100 125 100 Fm, PHASE MARGIN () VCC - VEE = 5.0 V VCC - VEE = 1.0 V VCC - VEE = 5.0 V VCC - VEE = 1.0 V RL = 600 W CL = 0 TA = 25C 100 k 1.0 M 80 100 VCC - VEE = 5.0 V RL = 600 W CL = 100 pF 60 Phase Margin 40 40 20 0 -55 10 M -25 0 0 125 100 50 VCC - VEE = 5.0 V RL = 600 W CL = 100 pF TA = 25C 40 30 20 20 Gain Margin VCC - VEE = 5.0 V RL = 600 W TA = 25C Phase Margin 50 50 40 40 30 30 20 20 Gain Margin 10 10 10 0 3.0 0 1.0 M 100 k 60 AV GAIN MARGIN (dB) Fm, PHASE MARGIN () Phase Margin 10 k 75 60 60 60 1.0 k 50 Figure 24. Gain and Phase Margin versus Temperature 70 100 25 TA, AMBIENT TEMPERATURE (C) 70 10 20 Gain Margin Figure 23. Voltage Gain and Phase versus Frequency 50 80 60 f, FREQUENCY (Hz) Fm, PHASE MARGIN () 75 Figure 22. Gain Bandwidth Product versus Temperature -40 10 k 0 10 50 Figure 21. Slew Rate versus Temperature 0 30 25 TA, AMBIENT TEMPERATURE (C) 20 40 0 TA, AMBIENT TEMPERATURE (C) 40 AVOL, GAIN (dB) 4.0 125 60 -20 5.0 AV , GAIN MARGIN (dB) VCC - VEE = 5.0 V + Slew Rate 10 30 100 300 1000 0 3000 CL, CAPACITIVE LOAD (pF) RT, DIFFERENTIAL SOURCE RESISTANCE (W) Figure 25. Gain and Phase Margin versus Differential Source Resistance Figure 26. Feedback Loop Gain and Phase versus Capacitive Load http://onsemi.com 10 AV , GAIN MARGIN (dB) SR, SLEW RATE (V/ s) VCC - VEE = 1.0 V + Slew Rate GBW, GAIN BANDWIDTH PRODUCT (MHz) 4.0 MC33501, MC33503 8.0 120 80 60 40 20 VCC - VEE = 5.0 V RL = 600 W VO = 4.0 Vpp TA = 25C 100 300 10 k 30 k 100 k RL= 600 W TA = 25C 6.0 4.0 2.0 0 300 k 0.5 0 1.5 2.0 2.5 3.0 VCC, |VEE|, SUPPLY VOLTAGE (V) Figure 27. Channel Separation versus Frequency Figure 28. Output Voltage Swing versus Supply Voltage 3.5 100 70 VCC - VEE = 5.0 V TA = 25C 60 50 40 30 20 100 RL = 600 W CL = 0 TA = 25C 80 80 Phase Margin 60 60 40 40 20 20 Gain Margin 10 0 10 100 10 k 1.0 k 0 100 k 0 1 0 2 f, FREQUENCY (Hz) 4 5 6 7 Figure 30. Gain and Phase Margin versus Supply Voltage 1.6 120 AVOL, OPEN LOOP GAIN (dB) AVOL 10 dB RL = 600 W 1.2 0.8 0.4 0 -55 3 VCC - VEE, SUPPLY VOLTAGE (V) Figure 29. Equivalent Input Noise Voltage versus Frequency VCC-VEE, USEABLE SUPPLY VOLTAGE (V) 1.0 f, FREQUENCY (Hz) AV, GAIN MARGIN (dB) AV = 10 0 30 en, EQUIVALENT INPUT NOISE VOLTAGE (nV/ Hz) VO, OUTPUT VOLTAGE (Vpp) 100 Fm, PHASE MARGIN () CS, CHANNEL SEPARATION (dB) AV = 100 -25 0 25 50 75 100 100 80 60 40 0 125 RL = 600 W TA = 25C 20 0 1.0 2.0 3.0 4.0 TA, AMBIENT TEMPERATURE (C) VCC - VEE, SUPPLY VOLTAGE (V) Figure 31. Useable Supply Voltage versus Temperature Figure 32. Open Loop Gain versus Supply Voltage http://onsemi.com 11 5.0 6.0 MC33501, MC33503 RT 470 k 1.0 V CT 1.0 nF 1.0 Vpp - fO 1.0 kHz + R1a 470 k f + O R C In T T VCC R2 470 k R1b 470 k 1 2 (R 1a ) R R2 1b ) Figure 33. 1.0 V Oscillator Af Cf 400 pF Rf 100 k fL fH 0.5 V R2 10 k 1 f + [ 200 Hz L 2pR C 1 1 + VO - C1 80 nF 1 [ 4.0 kHz f + H 2pRC f f R1 10 k -0.5 V R A + 1 ) f + 11 f R2 Figure 34. 1.0 V Voiceband Filter http://onsemi.com 12 MC33501, MC33503 5.0 V Vref 15 V 15 13 2 16 4 3 1 FB 11 Output A 14 Output B MC34025 22 k 5 4.7 4.7 8 12 6 0.1 10 470 pF 7 9 From Current Sense 100 k 1.0 k + MC33502 - 3320 Provides current sense amplification and eliminates leading edge spike. 1.0 k Figure 35. Power Supply Application IO 1.0 V VO Rsense R3 1.0 k IO IL 435 mA 463 mA 212 mA 492 mA DIO/DIL R4 R1 1.0 k + - 1.0 k -120 x 10-6 R5 VL 2.4 k RL 75 IL For best performance, use low tolerance resistors. R2 3.3 k Figure 36. 1.0 V Current Pump http://onsemi.com 13 MC33501, MC33503 PACKAGE DIMENSIONS SOT23-5 (TSOP-5, SC59-5) SN SUFFIX CASE 483-02 ISSUE E D S 5 4 1 2 3 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. A AND B DIMENSIONS DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. B L G A DIM A B C D G H J K L M S J C 0.05 (0.002) H M K MILLIMETERS MIN MAX 2.90 3.10 1.30 1.70 0.90 1.10 0.25 0.50 0.85 1.05 0.013 0.100 0.10 0.26 0.20 0.60 1.25 1.55 0_ 10 _ 2.50 3.00 INCHES MIN MAX 0.1142 0.1220 0.0512 0.0669 0.0354 0.0433 0.0098 0.0197 0.0335 0.0413 0.0005 0.0040 0.0040 0.0102 0.0079 0.0236 0.0493 0.0610 0_ 10 _ 0.0985 0.1181 SOLDERING FOOTPRINT* 0.95 0.037 1.9 0.074 2.4 0.094 1.0 0.039 0.7 0.028 SCALE 10:1 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. SMARTMOS is a trademark of Motorola, Inc. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 14 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC33501/D