128K x 36, 3.3V Synchronous IDT71V546 Feature, SRAM with ZBT Burst Counter and Pipelined Outputs Features 128K x 36 memory configuration, pipelined outputs Supports high performance system speed - 133 MHz (4.2 ns Clock-to-Data Access) ZBTTM Feature - No dead cycles between write and read cycles Internally synchronized registered outputs eliminate the need to control OE Single R/W (READ/WRITE) control pin Positive clock-edge triggered address, data, and control signal registers for fully pipelined applications 4-word burst capability (interleaved or linear) Individual byte write (BW1 - BW4) control (May tie active) Three chip enables for simple depth expansion Single 3.3V power supply (+/- 5%) Packaged in a JEDEC standard 100-pin TQFP package clock cycle, and two cycles later its associated data cycle occurs, be it read or write. The IDT71V546 contains data I/O, address and control signal registers. Output enable is the only asynchronous signal and can be used to disable the outputs at any given time. A Clock Enable (CEN) pin allows operation of the IDT71V546 to be suspended as long as necessary. All synchronous inputs are ignored when (CEN) is high and the internal device registers will hold their previous values. There are three chip enable pins (CE1, CE2, CE2) that allow the user to deselect the device when desired. If any one of these three are not active when ADV/LD is low, no new memory operation can be initiated and any burst that was in progress is stopped. However, any pending data transfers (reads or writes) will be completed. The data bus will tri-state two cycles after chip is deselected or a write initiated. The IDT71V546 has an on-chip burst counter. In the burst mode, the IDT71V546 can provide four cycles of data for a single address presented to the SRAM. The order of the burst sequence is defined by the LBO input pin. The LBO pin selects between linear and interleaved burst sequence. The ADV/LD signal is used to load a new external address (ADV/LD = LOW) or increment the internal burst counter (ADV/LD = HIGH). The IDT71V546 SRAM utilizes IDT's high-performance, high-volume 3.3V CMOS process, and is packaged in a JEDEC Standard 14mm x 20mm 100-pin thin plastic quad flatpack (TQFP) for high board density. Description The IDT71V546 is a 3.3V high-speed 4,718,592-bit (4.5 Megabit) synchronous SRAM organized as 128K x 36 bits. It is designed to eliminate dead bus cycles when turning the bus around between reads and writes, or writes and reads. Thus it has been given the name ZBTTM, or Zero Bus Turn-around. Address and control signals are applied to the SRAM during one Pin Description Summary A0 - A16 Address Inputs Input Synchronous Three Chip Enables Input Synchronous OE Output Enable Input Asynchronous R/W Read/Write Signal Input Synchronous CEN Clock Enable Input Synchronous Individual Byte Write Selects Input Synchronous Clock Input N/A Advance Burst Address / Load New Address Input Synchronous Linear / Interleaved Burst Order Input Static I/O Synchronous CE1, CE2, CE2 BW1, BW2, BW3, BW4 CLK ADV/LD LBO I/O0 - I/O31, I/OP1 - I/OP4 Data Input/Output VDD 3.3V Power Supply Static VSS Ground Supply Static 3821 tbl 01 ZBT and Zero Bus Turnaround are trademarks of Integrated Device Technology, Inc. and the architecture is supported by Micron Technology and Motorola Inc. SEPTEMBER 1999 1 (c)1999 Integrated Device Technology, Inc. DSC-3821/2 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Pin Definitions(1) Symbol Pin Function I/O Active Description A0 - A16 Address Inputs I N/A Synchronous Address inputs. The address register is triggered by a combination of the rising edge of CLK and ADV/LD Low, CEN Low and true chip enables. ADV/LD Address/Load I N/A ADV/LD is a synchronous input that is used to load the internal registers with new address and control when it is sampled low at the rising edge of clock with the chip selected. When ADV/LD is low with the chip deselected, any burst in progress is terminated. When ADV/LD is sampled high then the internal burst counter is advanced for any burst that was in progress. The external addresses are ignored when ADV/LD is sampled high. R/W Read/Write I N/A R/W signal is a synchronous input that identified whether the current load cycle initiated is a Read or Write access to the memory array. The data bus activity for the current cycle takes place two clock cycles later. CEN Clock Enable I LOW Synchrono us Clock Enable Input. When CEN is sampled high, all other synchronous inputs, includ ing clock are ignored and outputs remain unchanged. The effect of CEN samp led high on the device outputs is as if the low to high clock transition did not occur. For normal operation, CEN must be sampled low at rising edge of clock. BW1 - BW4 Individual Byte Write Enables I LOW Synchronous byte write enables. Enable 9-bit byte has its own active low byte write enable. On load write cycles (When R/W and ADV/LD are sampled low) the appropriate byte write signal (BW1 - BW4) must be valid. The byte write signal must also be valid on each cycle of a burst write. Byte Write signals are ignored when R/W is sampled high. The appropriate byte(s) of data are written into the device two cycles later. BW1 - BW4 can all be tied low if always doing write to the entire 36-bit word. CE1, CE2 Chip Enables I LOW Synchro nous active low chip enable. CE1 and CE2 are used with CE2 to enable the IDT71V546. (CE1 or CE2 sampled high or CE2 sampled low) and ADV/LD low at the rising edge of clock, initiates a deselect cycle. the ZBT has a two cycle deselect, i.e., the data bus will tri-state two clock cycles after deselect is initiated. CE2 Chip Enable I HIGH Synchronout active high chip enable. CE2 is used with CE1 and CE2 to enable the chip. CE2 has inverted polarity but otherwise identical to CE1 and CE2. CLK Clock I N/A This is the clock input to the IDT71V546. Except for OE, all timing references for the device are made with respect to the rising edge of CLK. I/O0 - I/O31 I/OP1 - I/OP4 Data Input/Output I/O N/A Synchronous data input/output (I/O) pins. Both the data input path and data output path are registered and triggered by the rising edge of CLK. LBO Linear Burst Order I LOW Burst order selection input. When LBO is high the Interleaved burst sequence is selected. When LBO is low the Linear burst sequence is selected. LBO is a static DC input. OE Output Enable I LOW Asynchronous output enable. OE must be low to read data from the 71V546. When OE is high the I/O pins are in a high-impedance state. OE does not need to be actively controlled for read and write cycles. In normal operation, OE can be tied low. VDD Power Supply N/A N/A 3.3V power supply input. VSS Ground N/A N/A Ground pin. NOTE: 1. All synchronous inputs must meet specified setup and hold times with respect to CLK. 2 3821 tbl 02 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Functional Block Diagram LBO Address A [0:16] CE1, CE2, CE2 R/W 128K x 36 BIT MEMORY ARRAY D Q Address D Q Control Input Register CEN ADV/LD BWx D DI Q DO Control Logic Clk Mux Sel D Clk Clock Output Register Q Gate OE . 3821 drw 01 Data I/O [0:31], I/O P[1:4] Recommended DC Operating Conditions Recommended Operating Temperature and Supply Voltage Grade Commercial Symbol Temperature VSS VDD 0OC to +70OC 0V 3.3V + 5% 3821 tbl 03 Parameter Min. Typ. Max. Unit 3.135 3.3 3.465 V 0 0 0 V 4.6 V V VDD Supply Voltage VSS Ground V IH Input High Voltage - Inputs 2.0 ____ V IH Input High Voltage - I/O 2.0 ____ V DD+0.3(2) VIL Input Low Voltage -0.5(1) ____ 0.8 V 3821 tbl 04 NOTES: 1. VIL (min.) = 1.0V for pulse width less than tCYC/2, once per cycle. 2. VIH (max.) = +6.0V for pulse width less than tCYC/2, once per cycle. 3 6.42 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs CE2 BW4 BW3 BW2 BW1 CE2 VDD VSS CLK R/W CEN OE ADV/LD NC(2) NC(2) A8 A9 A6 A7 CE1 Pin Configuration Commercial Temperature Range 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 I/OP3 I/O16 I/O17 VDD VSS I/O18 I/O19 I/O20 I/O21 VSS VDD I/O22 I/O23 VDD(1) VDD VDD VSS I/O24 I/O25 VDD VSS I/O26 I/O27 I/O28 I/O29 VSS VDD I/O30 I/O31 I/OP4 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 71 10 11 70 12 69 13 68 14 67 15 66 PK100-1 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 28 54 53 29 52 51 30 I/OP2 I/O15 I/O14 VDD VSS I/O13 I/O12 I/O11 I/O10 VSS VDD I/O9 I/O8 VSS VDD VDD VSS I/O7 I/O6 VDD VSS I/O5 I/O4 I/O3 I/O2 VSS VDD I/O1 I/O0 I/OP1 . . A10 A11 A12 A13 A14 A15 A16 VSS VDD NC NC LBO A5 A4 A3 A2 A1 A0 NC NC 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 3821 drw 02 TOP VIEW TQFP NOTES: 1. Pin 14 does not have to be connected directly to VDD as long as the input voltage is > VIH. 2. Pin 83 and 84 are reserved for future A17 (8M) and A18 (16M) respectively. Absolute Maximum Ratings(1) Symbol Rating Capacitance Commercial Unit VTERM(2) Terminal Voltage with Respect to GND -0.5 to +4.6 V (3) Terminal Voltage with Respect to GND -0.5 to VDD+0.5 V TA Operating Temperature 0 to +70 o C TBIAS Temperature Under Bias -55 to +125 o C TSTG Storage Temperature -55 to +125 o C PT Power Dissipation 2.0 IOUT DC Output Current 50 VTERM (TA = +25C, f = 1.0MHz, TQFP package) Symbol Parameter(1) CIN Input Capacitance CI/O I/O Capacitance Conditions Max. Unit VIN = 3dV 5 pF VOUT = 3dV 7 pF 3821 tbl 06 NOTE: 1. This parameter is guaranteed by device characterization, but not production tested. W mA 3821 tbl 05 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VDD and Input terminals only. 3. I/O terminals. 4 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Synchronous Truth Table(1) CEN R/W Chip(5) Enable ADV/LD BWx ADDRESS USED PREVIOUIS CYCLE CURRENT CYCLE I/O (2 cycles later) L L Select L Valid External X LOAD WRITE D(7) L H Select L X External X LOAD READ Q(7) L X X H Valid Internal LOAD WRITE/ BURST WRITE BURST WRITE (Advance Burst Counter)(2) D(7) L X X H X Internal LOAD READ/ BURST READ BURST READ (Advance Burst Counter)(2) Q(7) L X Deselect L X X X DESELECT or STOP(3) HiZ L X X H X X DESELECT / NOOP NOOP HiZ H X X X X X (4) X SUSPEND Previous Value 3821 tbl 07 NOTES: 1. L = VIL, H = VIH, X = Dont Care. 2. When ADV/LD signal is sampled high, the internal burst counter is incremented. The R/W signal is ignored when the counter is advanced. Therefore the nature of the burst cycle (Read or Write) is determined by the status of the R/W signal when the first address is loaded at the beginning of the burst cycle. 3. Deselect cycle is initiated when either (CE1, or CE2 is sampled high or CE2 is sampled low) and ADV/LD is sampled low at rising edge of clock. The data bus will tri-state two cycles after deselect is initiated. 4. When CEN is sampled high at the rising edge of clock, that clock edge is blocked from propogating through the part. The state of all the internal registers and the I/ Os remains unchanged. 5. To select the chip requires CE1 = L, CE2 = L, CE2 = H on these chip enables. Chip is deselected if either one of the chip enables is false. 6. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up. 7. Q - Data read from the device, D - data written to the device. Partial Truth Table for Writes(1) Operation R/W BW1 BW2 BW3 BW4 READ H X X X X L L L L L WRITE BYTE 1 (I/O [0:7], I/O P1) L L H H H WRITE BYTE 2 (I/O [8:15], I/OP2)(2) L H L H H WRITE BYTE 3 (I/O [16:23], I/OP3)(2) L H H L H (2) L H H H L L H H H H WRITE ALL BYTES (2) WRITE BYTE 4 (I/O [24:31], I/OP4) NO WRITE 3821 tbl 08 NOTES: 1. L = VIL, H = VIH, X = Dont Care. 2. Multiple bytes may be selected during the same cycle. 5 6.42 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Interleaved Burst Sequence Table (LBO=VDD) Sequence 1 Sequence 2 Sequence 3 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 0 0 1 1 1 0 Third Address 1 0 1 1 0 0 0 1 1 1 1 0 0 1 0 0 Fourth Address (1) Sequence 4 3821 tbl 09 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Linear Burst Sequence Table (LBO=VSS) Sequence 1 Sequence 2 Sequence 3 A1 A0 A1 A0 A1 A0 A1 A0 First Address 0 0 0 1 1 0 1 1 Second Address 0 1 1 0 1 1 0 0 Third Address 1 0 1 1 0 0 0 1 1 1 0 0 0 1 1 0 Fourth Address (1) Sequence 4 3821 tbl 10 NOTE: 1. Upon completion of the Burst sequence the counter wraps around to its initial state and continues counting. Functional Timing Diagram(1) CYCLE n+29 n+30 n+31 n+32 n+33 n+34 n+35 n+36 n+37 A29 A30 A31 A32 A33 A34 A35 A36 A37 A37 C29 C30 C31 C32 C33 C34 C35 C36 C37 C37 D/Q27 D/Q28 D/Q29 D/Q30 D/Q31 D/Q32 D/Q33 D/Q34 D/Q35 CLOCK ADDRESS (A0 - A16) (2) (2) CONTROL (R/W, ADV/LD, BWx) (2) DATA I/O [0:31], I/O P[1:4] NOTE: 3821 drw 03 1. This assumes CEN, CE1, CE2, CE2 are all true. 2. All Address, Control and Data_In are only required to meet set-up and hold time with respect to the rising edge of clock. Data_Out is valid after a clock-to-data delay from the rising edge of clock. 6 , IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Device Operation - Showing Mixed Load, Burst, Deselect and NOOP Cycles(2) Cycle Address R/W ADV/LD CE(1) CEN BWx OE I/O n A0 H L L L X X X Load read n+1 X X H X L X X X Burst read n+2 A1 H L L L X L Q0 Load read n+3 X X L H L X L Q0+1 Deselect or STOP n+4 X X H X L X L Q1 NOOP n+5 A2 H L L L X X Z Load read n+6 X X H X L X X Z Burst read n+7 X X L H L X L Q2 Deselect or STOP n+8 A3 L L L L L L Q2+1 Load write n+9 X X H X L L X Z Burst write n+10 A4 L L L L L X D3 Load write n+11 X X L H L X X D3+1 Deselect or STOP n+12 X X H X L X X D4 NOOP n+13 A5 L L L L L X Z Load write n+14 A6 H L L L X X Z Load read n+15 A7 L L L L L X D5 Load write n+16 X X H X L L L Q6 Burst write n+17 A8 H L L L X X D7 Load read n+18 X X H X L X X D7+1 Burst read n+19 A9 L L L L L L Q8 Load write NOTES: 1. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 2. H = High; L = Low; X = Dont Care; Z = High Impedance. 7 6.42 Comments 3821 tbl 11 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Read Operation(1) Cycle Address R/W ADV/LD CE(2) CEN BWx OE I/O n A0 H L L L X X X Address and Control meet setup n+1 X X X X L X X X Clock Setup Valid n+2 X X X X X X L Q0 Co ntents of Address A0 Read Out Comments 3821 tbl 12 NOTE: 1. H = High; L = Low; X = Dont Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Burst Read Operation(1) Cycle Address R/W ADV/LD CE(2) CEN BWx OE I/O n A0 H L L L X X X Address and Control meet setup n+1 X X H X L X X X Clock Setup Valid, Advance Counter n+2 X X H X L X L Q0 Ad dress A0 Read Out, Inc. Count n+3 X X H X L X L Q0+1 Address A0+1 Read Out, Inc. Count n+4 X X H X L X L Q0+2 Address A0+2 Read Out, Inc. Count n+5 A1 H L L L X L Q0+3 Address A0+3 Read Out, Load A1 n+6 X X H X L X L Q0 Ad dress A0 Read Out, Inc. Count n+7 X X H X L X L Q1 Ad dress A1 Read Out, Inc. Count n+8 A2 H L L L X L Q1+1 Address A1+1 Read Out, Load A2 NOTE: 1. H = High; L = Low; X = Dont Care; Z = High Impedance.. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 8 Comments 3821 tbl 13 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Write Operation(1) Cycle Address R/W ADV/LD CE(2) CEN BWx OE I/O n A0 L L L L L X X Address and Control meet setup n+1 X X X X L X X X Clock Setup Valid n+2 X X X X L X X D0 Write to Address A0 Comments 3821 tbl 14 NOTE: 1. H = High; L = Low; X = Dont Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Burst Write Operation(1) Cycle Address R/W ADV/LD CE(2) CEN BWx OE I/O n A0 L L L L L X X Address and Control meet setup n+1 X X H X L L X X Clock Setup Valid, Inc. Count n+2 X X H X L L X D0 Address A0 Write, Inc. Count n+3 X X H X L L X D0+1 Address A 0+1 Write, Inc. Count n+4 X X H X L L X D0+2 Address A 0+2 Write, Inc. Count n+5 A1 L L L L L X D0+3 Address A 0+3 Write, Load A1 n+6 X X H X L L X D0 Address A0 Write, Inc. Count n+7 X X H X L L X D1 Address A1 Write, Inc. Count n+8 A2 L L L L L X D1+1 Address A 1+1 Write, Load A2 NOTE: 1. H = High; L = Low; X = Dont Care; ? = Dont Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 9 6.42 Comments 3821 tbl 15 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Read Operation With Clock Enable Used(1) Cycle Address R/W ADV/LD CE(2) CEN BWx OE I/O n A0 H L L L X X X Address and Control meet setup n+1 X X X X H X X X Clock n+1 Ignored n+2 A1 H L L L X X X Clock Valid n+3 X X X X H X L Q0 Clock Ignored. Data Q0 is on the bus n+4 X X X X H X L Q0 Clock Ignored. Data Q0 is on the bus n+5 A2 H L L L X L Q0 Address A0 Read out (but trans.) n+6 A3 H L L L X L Q1 Ad dress A1 Read out (bus trans.) n+7 A4 H L L L X L Q2 Ad dress A2 Read out (bus trans.) Comments 3821 tbl 16 NOTE: 1. H = High; L = Low; X = Dont Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. Write Operation with Clock Enable Used(1) Cycle Address R/W ADV/LD CE(2) CEN BWx OE I/O n A0 L L L L L X X Address and Control meet setup n+1 X X X X H X X X Clock n+1 Ignored n+2 A1 L L L L L X X Clock Valid n+3 X X X X H X X X Clock Ignored n+4 X X X X H X X X Clock Ignored n+5 A2 L L L L L X D0 Write data D0 n+6 A3 L L L L L X D1 Write data D1 n+7 A4 L L L L L X D2 Write data D2 NOTE: 1. H = High; L = Low; X = Dont Care; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 10 Comments 3821 tbl 17 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Read Operation With Chip Enable Used(1) Cycle Address R/W ADV/LD CE(1) CEN BWx OE I/O n X X L H L X X ? Deselected n+1 X X L H L X X ? Deselected n+2 A0 H L L L X X Z Address and Control meet setup n+3 X X L H L X X Z Deselected or STOP n+4 A1 H L L L X L Q0 Address A0 read out. Load A1 n+5 X X L H L X X Z Deselected or STOP n+6 X X L H L X L Q1 Address A1 Read out. Deselected n+7 A2 H L L L X X Z Address and Control meet setup n+8 X X L H L X X Z Deselected or STOP n+9 X X L H L X L Q2 Address A2 read out. Deselected Comments 3821 tbl 18 NOTES: 1. H = High; L = Low; X = Dont Care; ? = Dont Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 3. Device Outputs are ensured to be in High-Z after the first rising edge of clock upon power-up. Write Operation With Chip Enable Used(1) Cycle Address R/W ADV/LD CE(1) CEN BWx OE I/O n X X L H L X X ? Deselected n+1 X X L H L X X ? Deselected n+2 A0 L L L L L X Z Address and Control meet setup n+3 X X L H L X X Z Deselected or STOP n+4 A1 L L L L L X D0 Address D0 Write In. Load A1 n+5 X X L H L X X Z Deselected or STOP n+6 X X L H L X X D1 Address D1 Write In. Deselected n+7 A2 L L L L L X Z Address and Control meet setup n+8 X X L H L X X Z Deselected or STOP n+9 X X L H L X X D2 Address D2 Write In. Deselected NOTES: 1. H = High; L = Low; X = Dont Care; ? = Dont Know; Z = High Impedance. 2. CE = L is defined as CE1 = L, CE2 = L and CE2 = H. CE = H is defined as CE1 = H, CE2 = H or CE2 = L. 11 6.42 Comments 3821 tbl 19 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 3.3V +/-5%) Symbol Parameter Test Conditions Min. Max. Unit |ILI| Input Leakage Current VDD = Max., VIN = 0V to VDD ___ 5 A |ILI| LBO Input Leakage Current(1) VDD = Max., VIN = 0V to VDD ___ 30 A |ILO| Output Leakage Current CE > VIH or OE > VIH, VOUT = 0V toVDD, VDD = Max. ___ 5 A VOL Output Low Voltage IOL = 5mA, VDD = Min. ___ 0.4 V VOH Output High Voltage IOH = -5mA, VDD = Min. 2.4 ___ V 3821 tbl 20 NOTE: 1. The LBO pin will be internally pulled to VDD if it is not actively driven in the application. DC Electrical Characteristics Over the Opearting Temperature and Supply Voltage Range(1) (VDD = 3.3V +/-5%, VHD = VDD0.2V, VLD = 0.2V) Symbol Parameter Test Conditions S133 S117 S100 Unit IDD Operating Power Supply Current Device Selected, Outputs Open, ADV/LD = X, VDD = Max., VIN > VIH or < VIL, f = fMAX(2) 300 275 250 mA ISB1 CMOS Standby Power Supply Current Device Deselected, Outputs Open, VDD = Max., VIN > VHD or < VLD, f = 0(2) 40 40 40 mA ISB2 Clock Running Power Supply Current Device Deselected, Outputs Open, VDD = Max., VIN > VHD or < VLD, f = fMAX(2) 110 105 100 mA ISB3 Idle Power Supply Current Device Selected, Outputs Open, CEN > VIH VDD = Max., VIN > VHD or < VLD, f = fMAX(2) 40 40 40 mA 3821 tbl 21 NOTES: 1. All values are maximum guaranteed values. 2. At f = fMAX, inputs are cycling at the maximum frequency of read cycles of 1/tCYC; f=0 means no input lines are changing. AC Test Loads AC Test Conditions +1.5V Input Pulse Levels 50 I/O Z0 = 50 3821 drw 04 Figure 1. AC Test Load , 0 to 3V Input Rise/Fall Times 2ns Input Timing Reference Levels 1.5V Output Timing Reference Levels 1.5V AC Test Load See Figures 1 3821 tbl 22 6 5 4 tCD 3 (Typical, ns) 2 1 20 30 50 80 100 Capacitance (pF) 200 3821 drw 05 , Figure 2. Lumped Capacitive Load, Typical Derating 12 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range AC Electrical Characteristics (VDD = 3.3V +/-5%, TA = 0 to 70C) 71V546S133 Symbol Parameter 71V546S117 71V546S100 Min. Max. Min. Max. Min. Max. Unit Clock Parameters tCYC Clock Cycle Time 7.5 ____ 8.5 ____ 10 ____ ns (1) tF Clock Frequency ____ 133 ____ 117 ____ 100 MHz (2) Clock High Pulse Width 2.5 ____ 3 ____ 3.5 ____ ns (2) Clock Low Pulse Width 2.5 ____ 3 ____ 3.6 ____ ns Clock High to Valid Data ____ 4.2 ____ 4.5 ____ 5 ns tCH tCL Output Parameters tCD Clock High to Data Change 1.5 ____ 1.5 ____ 1.5 ____ ns (3,4,5) Clock High to Output Active 1.5 ____ 1.5 ____ 1.5 ____ ns (3,4,5) tCHZ Clock High to Data High-Z 1.5 3.5 1.5 3.5 1.5 3.5 ns tOE Output Enable Access Time ____ 4.2 ____ 4.5 ____ 5 ns 0 ____ 0 ____ 0 ____ ns tCDC tCLZ (3,4) Output Enable Low to Data Active (3.4) Output Enable High to Data High-Z ____ 3.5 ____ 3.5 ____ 3.5 ns tSE Clock Enable Setup Time 2.0 ____ 2.0 ____ 2.2 ____ ns tSA Address Setup Time 2.0 ____ 2.0 ____ 2.2 ____ ns tSD Data in Setup Time 1.7 ____ 1.7 ____ 2.0 ____ ns tSW Read/Write (R/W) Setup Time 2.0 ____ 2.0 ____ 2.2 ____ ns tSADV Advance/Load (ADV/LD) Setup Time 2.0 ____ 2.0 ____ 2.2 ____ ns tSC Chip Enable/Select Setup Time 2.0 ____ 2.0 ____ 2.2 ____ ns tSB Byte Write Enable (BWx) Setup Time 2.0 ____ 2.0 ____ 2.2 ____ ns tHE Clock Enable Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHA Address Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHD Data in Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHW Read/Write (R/W) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHADV Advance/Load (ADV/LD) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHC Chip Enable/Select Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tHB Byte Write Enable (BWx) Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tOLZ tOHZ Setup Times Hold Times 3821 tbl 23 NOTES: 1. tF = 1/tCYC. 2. Measured as HIGH above 2.0V and LOW below 0.8V. 3. Transition is measured 200mV from steady-state. 4. These parameters are guaranteed with the AC load (Figure 1) by device characterization. They are not production tested. 5. To avoid bus contention, the output buffers are designed such that tCHZ (device turn-off) is about 2 ns faster than tCLZ (device turn-on) at a given temperature and voltage. The specs as shown do not imply bus contention because tCLZ is a Min. parameter that is worse case at totally different test conditions (0 deg. C, 3.465V) than tCHZ, which is a Max. parameter (worse case at 70 deg. C, 3.135V). 13 6.42 14 A1 tSADV tHA tHW tHE tCLZ tHC Pipeline Read tSC A2 tSA tSW tSE tCD Pipeline Read O1(A1) tHADV tCH O1(A2) tCDC tCL Q(A2+1) Q(A2+2) (CEN high, eliminates current L-H clock edge) Burst Pipeline Read tCD Q(A2+2) tCDC Q(A2+3) O1(A2) tCHZ 3821 drw 06 (Burst Wraps around to initial state) NOTES: 1. Q (A1) represents the first output from the external address A1. Q (A2) represents the first output from the external address A2; Q (A2+1) represents the next output data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. DATA Out OE BW1,BW4 CE1,CE2(2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Timing Waveform of Read Cycle(1,2,3,4) 15 6.42 A1 tSADV tHA tHW tHE tHB tHC Pipeline Write tSB tSC A2 tSA tSW tSE tHD Pipeline Write D(A1) tSD tHADV tCH tCL D(A2) . D (A2+1) Burst Pipeline Write (CEN high, eliminates current L-H clock edge) tSD D (A2+2) tHD 3821 drw 07 D (A2+3) (Burst Wraps around to initial state) D(A2) NOTES: 1. D (A1) represents the first input to the external address A1. D (A2) represents the first input to the external address A2; D (A2+1) represents the next input data in the burst sequence of the base address A2, etc. where address bits A0 and A1 are advancing for the four word burst in the sequence defined by the state of the LBO input. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Burst ends when new address and control are loaded into the SRAM by sampling ADV/LD LOW. 4. R/W is don't care when the SRAM is bursting (ADV/LD sampled HIGH). The nature of the burst access (Read or Write) is fixed by the state of the R/W signal when new address and control are loaded into the SRAM. 5. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATA In OE BW1,BW4 CE1,CE2 (2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Timing Waveform of Write Cycles(1,2,3,4,5) 16 A1 tSADV tHA tHW tHE tCD tHB tHC Read tSB tSC A2 tSA tSW tSE A3 Q(A1) Write tHADV tCH tCHZ Read tCLZ D(A2) tSD tHD A4 tCL Q(A3) tCDC Write A5 D(A4) A6 Read D(A5) A7 Q(A6) A8 Q(A7) A9 3821 drw 08 NOTES: 1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATA Out DATA In OE BW1 - BW4 CE1, CE2 (2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Timing Waveform of Combined Read and Write Cycles(1,2,3) . 17 6.42 A1 tSE tSADV tHE tHA tHW tHB tHC tCD tCLZ B(A2) tSB tSC A2 tSA tSW tCH tHADV Q(A1) tCL tCHZ tCDC Q(A1) A3 D(A2) tSD tHD A4 . NOTES: 1. Q (A1) represents the first output from the external address A1. D (A2) represents the input data to the SRAM corresponding to address A2. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH.. 3. CEN when sampled high on the rising edge of clock will block that L-H transition of the clock from propogating into the SRAM. The part will behave as if the L-H clock transition did not occur. All internal registers in the SRAM will retain their previous state. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATA Out DATA In OE BW1 - BW4 CE1, CE2 (2) ADDRESS R/W ADV/LD CEN CLK tCYC 3821 drw 09 Q(A3) A5 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Timing Waveform of CEN Operation(1,2,3,4) 18 A1 tSADV tHA tHW tHE tSC tCLZ tCD tHC A2 tSA tSW tSE Q(A1) tHADV tCH tCDC tCHZ tHB Q(A2) tSB A3 tCL D(A3) tSD tHD A4 Q(A3) A5 3821 drw 10 NOTES: 1. Q (A1) represents the first output from the external address A1. D (A3) represents the input data to the SRAM corresponding to address A3 etc. 2. CE2 timing transitions are identical but inverted to the CE1 and CE2 signals. For example, when CE1 and CE2 are LOW on this waveform, CE2 is HIGH. 3. When either one of the Chip enables (CE1, CE2, CE2) is sampled inactive at the rising clock edge, a deselect cycle is initiated. The data-bus tri-states two cycles after the initiation of the deselect cycle. This allows for any pending data transfers (reads or writes) to be completed. 4. Individual Byte Write signals (BWx) must be valid on all write and burst-write cycles. A write cycle is initiated when R/W signal is sampled LOW. The byte write information comes in two cycles before the actual data is presented to the SRAM. DATA Out DATA In OE BW1 - BW4 CE1,CE2 (2) ADDRESS R/W ADV/LD CEN CLK tCYC IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Timing Waveform of CS Operation(1,2,3,4) IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Timing Waveform of OE Operation(1) OE tOE tOHZ tOLZ Valid DATA Out NOTE: 1. A read operation is assumed to be in progress. 3821 drw 11 Ordering Information IDT 71V546 S XX PF Device Type Power Speed Package PF Plastic Thin Quad Flatpack, 100 pin (PK100-1) 133 117 100 Clock Frequency in Megahertz PART NUMBER TCD PARAMETER SPEED IN MEGAHERTZ CLOCK CYCLE TIME 71V546S133PF 4.2 ns 133 MHz 7.5 ns 71V546S117PF 4.5 ns 117 MHz 8.5 ns 71V546100PF 5 ns 100 MHz 10 ns 3821 drw 12 19 6.42 IDT71V546 128K x 36 3.3V Synchronous SRAM with ZBT Feature, Burst Counter and Pipelined Outputs Commercial Temperature Range Datasheet Document History 6/15/99 9/13/99 Pg. 12 Pg. 20 Updated to new format Corrected ISB3 conditions Added Datasheet Document History CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 20 for Tech Support: sramhelp@idt.com 800-544-7726, x4033