www.vishay.com For technical questions, contact: ff2aresistors@vishay.com Document Number: 31027
48 Revision: 11-Mar-10
CMF (Military RN and RL)
Vishay Dale
Metal Film Resistors, Military, MIL-R-10509 Qualified,
Precision, Type RN and MIL-PRF-22684 Qualified, Type RL
FEATURES
•Very low noise (- 40 dB)
•Very low voltage coefficient (5 ppm/V)
•Controlled temperature coefficient
•Flame retardant epoxy coating
•Commercial alternatives to military styles are available
with higher power ratings. See appropriate catalog or web
page.
Notes
(1) Continuous working voltage shall be or maximum working voltage, whichever is less.
(2) Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 Rev. D.
STANDARD ELECTRICAL SPECIFICATIONS
VISHAY
DALE
MODEL
MIL
STYLE
MIL
SPEC.
SHEET
POWER
RATING TOLERANCE
± %
MAX.
WORKING
VOLTAGE (1)
V
RESISTANCE RANGE
ΩDIELECTRIC
STRENGTH
VAC
P70 °C
WP125 °C
W
MIL-R-10509 MIL-
PRF-
22684
± 100 ppm/°C
(D) ± 50 ppm/°C
(C) ± 25 ppm/°C
(E)
CMF50 RN50 08 - 0.05 0.1, 0.25,
0.5, 1 200 - 10 to 100K 10 to 100K - 450
CMF55 RN55 07 0.125 0.10 0.1, 0.25,
0.5, 1 200 10 to 301K 49.9 to 100K 49.9 to 100K - 450
CMF60 RN60 01 0.25 0.125 0.1, 0.25,
0.5, 1 300 10 to 1M 49.9 to 499K 49.9 to 499K - 500
CMF65 RN65 02 0.50 0.25 0.1, 0.25,
0.5, 1 350 10 to 2M 49.9 to 1M 49.9 to 1M - 900
CMF70 RN70 03 0.75 (2) 0.50 0.1, 0.25,
0.5, 1 500 10 to 2.49M 24.9 to 1M 24.9 to 1M - 900
CMF07 RL07 01 0.25 - 2, 5 250 - - - 51 to
150K 450
CMF20 RL20 02 0.50 - 2, 5 350 - - - 4.3 to
470K 700
TECHNICAL SPECIFICATIONS
PARAMETER UNIT CONDITION
Voltage Coefficient ppm/V 5 when measured between 10 % and full rated voltage
Insulation Resistance Ω≥ 1010 min. dry; ≥ 108 min. after moisture test
Operating Temperature Range °C - 65/+ 175 (see derating curves for military range)
Terminal Strength Ib 5 pound pull test for RL07/RL20; 2 pound pull test for all others
Solderability Continuous satisfactory coverage when tested in accordance
with MIL-R-10509 and MIL-PRF-22684
P x R
Document Number: 31027 For technical questions, contact: ff2aresistors@vishay.com www.vishay.com
Revision: 11-Mar-10 49
CMF (Military RN and RL)
Metal Film Resistors, Military, MIL-R-10509 Qualified,
Precision, Type RN and MIL-PRF-22684 Qualified, Type RL Vishay Dale
GLOBAL PART NUMBER INFORMATION
MIL STYLE TOLERANCE
CODE
RN50 E = 25 ppm 3 digit significant B = ± 0.1 %
RN55 C = 50 ppm figure, followed byC = ± 0.25 %
D = ± 0.5 %
0R01 = 10 Ω
2512 = 21.5 k Ω
2494 = 2.49 M Ω
New Global Part Numbering: RN60D3483FR36 (preferred part numbering format)
RN6 0D 3 4 83FR36
Historical Part Number example: RN60D3483F (will continue to be accepted)
3483DRN60
MIL STYLE CHARACTERISTIC RESISTANCE VALUE TOLERANCE CODE PACKAGING
RN65
RN70
RN60
= 100 ppm a multiplier
DF =
±
1 %
Blank = Standard
(Dash number)
R36
F
PACKAGING SPECIAL
CHARACTERISTIC RESISTANCE
VALUE B14 = Tin/lead, bulk
BSL = Tin/lead, bulk,
single lot date code
R36 = Tin/lead, T/R (full)
RE6 = Tin/lead, T/R (1000 pieces)
RSL = Tin/lead, T/R,
single lot date code
Use “R” for
values < 100 Ω
MIL STYLE TOLERANCE
CODE PACKAGING
RL07 S = Solderable 2 digit significant G = ± 2 %B14 = Tin/lead, bulk
BSL = Tin/lead, bulk, single lot date code
R36 = Tin/lead, T/R (full)
RE6 = Tin/lead, T/R (1000 pieces)
RSL = Tin/lead, T/R, single lot date code
RL20 figure, followed byJ = ± 5 %
a multiplier
4R3 = 4.3 Ω
202 = 2.0 k Ω
474 = 470 k Ω
New Global Part Numbering: RL07S471JR36 (preferred part numbering format)
Historical Part Number example: RL07S471J (will continue to be accepted)
MIL STYLE LEAD MATERIAL RESISTANCE VALUE TOLERANCE CODE PACKAGING
RL07S471JR36
RL07 S 471 J R36
LEAD MATERIAL RESISTANCE
VALUE
Use “R” for
values < 10 Ω
MATERIAL SPECIFICATIONS
Element Nickel-chrome alloy
CoatingFlame retardant epoxy, formulated for
superior moisture protection
Core Fire-cleaned high purity ceramic
Termination Standard lead material is solder-coated
copper. Solderable and weldable.
APPLICABLE MIL-SPECS
MIL-R-10509 and MIL-PRF-22684: The CMF models meet or
exceed the electrical, environmental and dimensional requirements
of MIL-R-10509 and MIL-PRF-22684.
Noise: Vishay Dale metal film resistors have exceptionally low
noise level. Average for standard resistance range is 0.10 µV per V
over a decade of frequency, with low and intermediate resistance
values typically below 0.05 µV per V.
CAGE CODE: 91637
ENVIRONMENTAL SPECIFICATIONS
General
Environmental performance is shown in the
Environmental Performance table. Test
methods are those specified in MIL-R-10509
and MIL-PRF-22684.
Shelf Life Resistance shifts due to storage at room
temperature are negligible.
www.vishay.com For technical questions, contact: ff2aresistors@vishay.com Document Number: 31027
50 Revision: 11-Mar-10
CMF (Military RN and RL)
Vishay Dale Metal Film Resistors, Military, MIL-R-10509 Qualified,
Precision, Type RN and MIL-PRF-22684 Qualified, Type RL
Vishay Dale CMF resistors have an operating temperature range of - 65 °C to + 175 °C. They must be derated according to the
following curves:
Note
(1) 0.290" (7.37) for ± 0.25 % and ± 0.1 % resistance tolerances
Notes
• Commercial equivalents of military styles are available with higher power ratings. Consult factory.
(1) Formerly rated at 1 W and is the direct replacement for RN70 of MIL-R-10509 Rev. D.
R
E
W
O
P
D
ETAR FO %
AMBIENT TEMPERATURE °C
120
100
80
60
40
20
0
MIL-R-10509
Char. C and E Rating
MIL-R-10509
Char. D Rating
MIL-PRF-22684
DERATING
170150130110907050
DIMENSIONS in inches (millimeters)
A
BD
C
(Max.)
1.50 ± 0.125
[38.10 ± 3.18]
VISHAY DALE
MODEL AB C
(Max.) D
CMF50 0.150 ± 0.020
(3.81 ± 0.51) 0.065 ± 0.015
(1.65 ± 0.38) 0.244
(6.20) 0.016 ± 0.002
(0.41 ± 0.05)
CMF55 0.240 ± 0.020
(6.10 ± 0.51) 0.090 ± 0.008
(2.29 ± 0.20) 0.278
(7.06) (1) 0.025 ± 0.002
(0.64 ± 0.05)
CMF60 0.344 ± 0.031
(8.74 ± 0.79) 0.145 ± 0.015
(3.68 ± 0.38) 0.425
(10.80) 0.025 ± 0.002
(0.64 ± 0.05)
CMF65 0.562 ± 0.031
(14.27 ± 0.79) 0.180 ± 0.015
(4.57 ± 0.38) 0.687
(17.45) 0.025 ± 0.002
(0.64 ± 0.05)
CMF70 0.562 ± 0.031
(14.27 ± 0.79) 0.180 ± 0.015
(4.57 ± 0.38) 0.687
(17.45) 0.032 ± 0.002
(0.81 ± 0.05)
CMF07 0.240 ± 0.020
(6.10 ± 0.51) 0.090 ± 0.008
(2.29 ± 0.20) 0.278
(7.06) 0.025 ± 0.002
(0.64 ± 0.05)
CMF20 0.375± 0.040
(9.53 ± 1.02) 0.145 ± 0.015
(3.68 ± 0.38) 0.425
(10.80) 0.032 ± 0.002
(0.81 ± 0.05)
MILITARY POWER RATING
WATTAGE
MILITARY QUALIFIED
MIL-R-10509 MIL-PRF-22684
AT + 70 °C
(D) AT + 125 °C
(C and E) AT + 70 °C
0.05 - RN50 -
0.10 - RN55 -
0.125 RN55 RN60 -
0.25 RN60 RN65 RL07
0.50 RN65 RN70 RL20
0.75 (1) RN70 - -
Document Number: 31027 For technical questions, contact: ff2aresistors@vishay.com www.vishay.com
Revision: 11-Mar-10 51
CMF (Military RN and RL)
Metal Film Resistors, Military, MIL-R-10509 Qualified,
Precision, Type RN and MIL-PRF-22684 Qualified, Type RL Vishay Dale
Note
• RL series are color banded per MIL-PRF-22684
THERMAL RESISTANCE
0
20
40
60
80
100
120
APPLIED POWER IN W
HEAT RISE (°C ABOVE AMBIENT)
0 0.125 0.25 0.375 0.5 0.625 0.75 0.875 1 1.125
CMF65,
CMF70
CMF50 CMF55
CMF60
CMF20
CMF07
MARKING Characteristics: D = 100 ppm, C = 50 ppm, E = 25 ppm
Tolerance: F = 1 %, D = 0.5 %, C = 0.25 %, B = 0.1 %
Value = three significant figures and multiplier
J = JAN (joint Army - Navy) brand
RN50: (3 lines) RN55, RN60, RN65, RN70 (4 lines)
J50D
1211
F137
JAN, type, characteristic
Value
Tolerance and 3 digit date code
DALE
0137J
RN55D
1211F
Company logo
4 digit date code and JAN brand
Type and characteristic
Value and Tolerance
PERFORMANCE
REQUIREMENT MIL-R-10509 MIL-PRF-22684
CHARACTERISTIC D CHARACTERISTIC C CHARACTERISTIC E
MIL Temperature Coefficient + 200 ppm/°C - 500 ppm/°C ± 50 ppm/°C ± 25 ppm/°C ± 200 ppm/°C
Applicable Vishay Dale
Temperature Coefficient ± 100 ppm/°C ± 50 ppm/°C ± 25 ppm/°C ± 200 ppm/°C
TEST MILmax. MILmax. MILmax. MILmax.
Thermal Shock ± 0.50 % ΔR± 0.25 % ΔR± 0.25 % ΔR± 1.00 % ΔR
Short Time Overload ± 0.50 % ΔR± 0.25 % ΔR± 0.25 % ΔR± 0.50 % ΔR
Low Temperature Operation ± 0.50 % ΔR± 0.25 % ΔR± 0.25 % ΔR± 0.50 % ΔR
Moisture Resistance ± 1.50 % ΔR± 0.50 % ΔR± 0.50 % ΔR± 1.50 % ΔR
Shock ± 0.50 % ΔR± 0.25 % ΔR± 0.25 % ΔR± 0.50 % ΔR
Vibration ± 0.50 % ΔR± 0.25 % ΔR± 0.25 % ΔR± 0.50 % ΔR
Load Life ± 1.00 % ΔR± 0.50 % ΔR± 0.50 % ΔR± 2.00 % ΔR
Dielectric Withstanding Voltage ± 0.50 % ΔR± 0.25 % ΔR± 0.25 % ΔR± 0.50 % ΔR
Effect of Solder ± 0.50 % ΔR± 0.10 % ΔR± 0.10 % ΔR± 0.50 % ΔR
