3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Pak 100 L/E Pinless Header
.100" × .100" Straight, 4-Wall 3000 Series
• Optional ejector latches
• Shrouded to minimize physical and chemical pin
damage
• Special holes secure pinless header to back panel
• Mounting holes to further secure header to board
• Stand-off height allows for one layer wire wrap
• See the Regulatory Information Appendix (RIA)
in the “RoHS compliance” section of
www.3Mconnectors.com for compliance information
Date Modified: May 22, 2012 TS-0161-B
Sheet 1 of 5
Physical
Insulator:
Material: Glass Filled Polyester (PBT)
Flammability: UL 94V-0
Color: Gray
Marking: 3M Logo, Part Identification Number and Orientation Triangle
UL File No.: E68080
*RoHS = Directive 2002/95/EC, Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
“RoHS compliant” means that the product or part does not contain any of the following substances in excess of the following proposed maximum
concentration values in any homogeneous material (unless exempt under RoHS): (a) 0.1% (by weight) for each of lead, mercury, hexavalent chromium,
polybrominated biphenyls or polybrominated diphenyl ethers; or (b) 0.01% (by weight) for cadmium.
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Pak 100 L/E Pinless Header
.100" × .100" Straight, 4-Wall 3000 Series
TS-0161-B
Sheet 2 of 5
3M
Interconnect Solutions
http://www.3M.com/interconnects/
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Pak 100 L/E Pinless Header
.100″ × .100″ Straight, 4-Wall
Table 1
Pin
Quantity
Part
Number
Dimensions
A B D
20 6420 1.76 [44.8] 1.605 [40.77] 1.21 [30.7]
26 6426 2.06 [52.4] 1.905 [48.39] 1.51 [38.3]
34 6434 2.46 [62.6] 2.305 [58.55] 1.91 [48.5]
40 6440 2.76 [70.2] 2.605 [66.17] 2.21 [56.1]
50 6450 3.26 [82.9] 3.105 [78.87] 2.71 [68.8]
-9200
Header with
Short Ejector/Latch
for 3M Sockets
without Strain Relief
-9000
Header with
No Ejector/Latch
-9300
Header with
Long Ejector/Latch for
3M Sockets with
Strain Relief
-9400
Header with
Ejector Only
.424 ± .010
[10.77]
.08
[2.0]
Note: This Ejector is a Nickel
plated Zinc Alloy casting.
.573 ± .010
[14.55]
.37 Ref
[9.4]
.46 Ref
[11.7]
.42 Ref
[10.7]
1.11
[28.2]
Ref
1.01
[25.7]
Ref
1.11
[28.2]
Ref
TS-0161-12
Sheet 2 of 3
.17
[4.3]
.100
[2.54]
.25
[6.4]
Section A-A
.25
[6.4]
.58
[14.7]
.72
[18.3]
Position 1
Orientation
Triangle
.38
[9.65]
2X .10
[2.5]
.16
[4.1]
See Note 4
64XX
.22
[5.6]
.30
[7.6]
.21
[5.3]
A
A
8X ∅ .031 ± .002
[.79 ]
(See Note 1 & 2 )
2X ∅ .100
[2.54]
(See Note 3)
Position 1
B
D
.32
[8.1]
A
See Note 1
.100 Typ
[2.54] .16
[4.06]
.08
[2.0]
Table 1
Pin
Quan-
tity
Part
Number
Dimensions
A B D
20 6420 1.76 [44.8] 1.605 [40.77] 1.21 [30.7]
26 6426 2.06 [52.4] 1.905 [48.39] 1.51 [38.3]
34 6434 2.46 [62.6] 2.305 [58.55] 1.91 [48.5]
40 6440 2.76 [70.2] 2.605 [66.17] 2.21 [56.1]
50 6450 3.26 [82.9] 3.105 [78.87] 2.71 [68.8]
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Pak 100 L/E Pinless Header
.100" × .100" Straight, 4-Wall 3000 Series
TS-0161-B
Sheet 3 of 5
Ordering Information
64XX-9X00
Inch
(mm)
± .005
± .1 ± .01
Tolerance Unless Noted
.0 .00 .000
Inch
[ ] Dimensions for
Reference only
Notes:
1.Accepts .025 ± .001 sq pins.
2.Four smaller holes at each end used for retention.
3.Accepts Rear and Front entry mounting hardware:
Rear entry: #4-24 thread cutting screw
3M Part # 3341-5
(∅ .116 [2.95] mounting hole)
Front entry (Prior to installation of Latch): #2-56 bolt and nut
3M Part # 3341-6. See illustrations on page 4.
(∅ .106 [2.69] mounting hole)
4.These polarization notches will accomodate 3M Polarization Keys 3518.
.106 or .116 Typ
[2.69] [2.95]
(See Note 3)
.353 Typ
[8.95]
H
.100 Typ
[2.54]
.300
[7.62]
.025 ± .001 Square
[0.64]
.580 ± .010
[14.73]
(For Flush Mounting)
.050
[1.27]
.100 Typ
[2.54]
Backplane Pin Field
Recommendations
Table 1
3M Part
Number Suffix Dimension H
-9000 0.86 [21.8]
-9200 1.60 [40.6]
-9300 1.78 [45.2]
-9400 1.70 [43.2]
Pin Quantity:
(See Table 1)
Latch/Ejector System
0= No Latch/Ejectors
2= Short, Roll Pin Latch/Ejectors (3M Part #3505-2 )
3= Long, Roll Pin Latch/Ejectors (3M Part #3505-3 )
4= Roll Pin Ejectors (3M Part #3505-4)
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnectors.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Pak 100 L/E Pinless Header
.100" × .100" Straight, 4-Wall 3000 Series
TS-0161-B
Sheet 4 of 5
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3M™ Three-Wall Header
.100” × .100” Latch/Ejector, Straight and Right Angle 3000 Series
TS-0771-E
Sheet 5 of 5
.321
[8.15]
.100 Dia
[2.54]
Polarizing Post
Note: Insert Post into one mounting hardware hole on
bottom of header. Set post to protrude .115” [2.92]
3201 -3 P B T G ra y
3201 -4 L C P B la c k
Polarizing Keys
.15
[3.8]
.09
[2.3]
A
Breakaway Tab .34 Ref
[8.6]
Note: #2216 B/A Scotchweld can be used to adhere keys.
Dim A
N3518 LCP Black .02
3518 PBT Gray .02
Mounting Hardware
.31
[7.9]
.50
[12.7]
Panhead Thread Cutting Screw:
#4-24 X 5/16”
Type: USA Std BT, Federal BG
Hex Head Bolt, Nut and W
asher
Bolt - #2-56 X 1/2”
3341-5
(Installed from bottom of board)
3341-6
(Must be inserted prior to latch o
n
vertical headers)
3341-5 & 6
Material - Stainless Steel
Not for use with Condo headers.
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
Please recycle. Printed in USA.
© 3M 2012. All rights reserved.
RIA-2217B-E
3
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3Mconnectors.com 3M is a trademark of 3M Company.
