100K ECL Digital Frequency Multiplier Module The 100K ECL Digital Frequency Multiplier Modules manufactured by Engineered Components Company are designed to provide a square wave output at a given frequency which can be synchronized by square wave inputs at sub-harmonic frequencies. The falling edge of the output waveform is synchronized to the falling edge of the input waveform. If no synchronizing input is present, the unit will free-run producing a continuous output square wave. Phase jitter at the output will increase as higher orders of multiplication are used. An inverted output is also supplied. The MTBF on these modules, when calculated per MIL-HDBK-217, for a 50 deg.C ground fixed environment and with 50VDC applied, is in excess of 1.9 million hours. The temperature coefficient of delay is less than +/-300 ppm/deg.C over the operating temperature range of 0 to +85 deg. C. The module is provided in a 12-pin DIP package, fully encapsulated in epoxy resin and is housed in a Diallyl Phthalate case, blue in color. The case marking is applied by silkscreen using white epoxy paint. The 8 copper leads are tin-lead plated and meet the solderability requirements of MIL-STD-202, Method 208. MECHANICAL DIAGRAM 4 IN 12 Synchronizing Circuitry Square Wave Oscillator 5 OUT 6 OUT 9 Ve Product Selection Table Part Number ECL-100K-DFMM-50 ECL-100K-DFMM-55 ECL-100K-DFMM-60 ECL-100K-DFMM-65 ECL-100K-DFMM-70 ECL-100K-DFMM-75 ECL-100K-DFMM-80 ECL-100K-DFMM-85 ECL-100K-DFMM-90 ECL-100K-DFMM-95 ECL-100K-DFMM-100 ECL-100K-DFMM-110 ECL-100K-DFMM-120 ECL-100K-DFMM-130 ECL-100K-DFMM-140 ECL-100K-DFMM-150 ECL-100K-DFMM-160 ECL-100K-DFMM-170 ECL-100K-DFMM-180 ECL-100K-DFMM-190 ECL-100K-DFMM-200 ECL-100K-DFMM-210 ECL-100K-DFMM-220 ECL-100K-DFMM-230 ECL-100K-DFMM-240 ECL-100K-DFMM-250 Output Frequency Tolerance +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% +/-2% Special modules can often be manufactured to provide for customer specific applications. .700 .250 .060 TYP. TYP. .325 Nominal Output Frequency 50 MHz 55 MHz 60 MHz 65 MHz 70 MHz 75 MHz 80 MHz 85 MHz 90 MHz 95 MHz 100 MHz 110 MHz 120 MHz 130 MHz 140 MHz 150 MHz 160 MHz 170 MHz 180 MHz 190 MHz 200 MHz 210 MHz 220 MHz 230 MHz 240 MHz 250 MHz .350 TYP. .020 DIA. TYP. .050 TYP. .100 TYP. YYWW V MADE IN USA BLOCK DIAGRAM .030 TYP. +/-.030 .160 DATE CODE IN Ve NC NC ECL-100KDFMM-100 .875 NC Top view V OUT OUT .700 Operating Specifications: All measurements made at 25 deg. C All measurements made with Ve = -4.5VDC, Vc = 0VDC All measurements made with (1) ECL output load All measurements made with a 50 ohm pulldown resistor to -2VDC at the input and output Operating Temperature: 0 to +85 deg. C Storage Temperature: -55 to +125 deg. C Vee Supply Voltage: -4.5 +/-5% VDC Vcc Supply Current: 102mA typical Logic "High" Input: Voltage: -0.88VDC min. Current: 700uA max. Logic "Low" Input: Voltage: -1.81VDC max. Current: 1.0uA min. Logic "High" Voltage Out: -1.025VDC min. Logic "Low" Voltage Out: -1.625VDC max. engineered components company A Division of Cornucopia Tool & Plastics, Inc. PO Box 1915, 448 Sherwood Rd., Paso Robles CA 93447 Phone: 805-369-0034 Fax: 805-369-0033 Web: www.ec2.com