XW2B-50G4 - OMRON - Pdf.Support

CSM_XW2B_DS_E_4_2

Standard-type Connector-Terminal Block Conversion Units

XW2B

Simplifies Connector and terminal

block replacement, and requires less

in-panel wiring.

• Mount to DIN Track or via screws.

• MIL Flat Cable Connectors and Multi-pole, Square

Connectors are standard.

• Terminal blocks available with either M3 or M3.5 screws.

• Connecting Cables for Programmable Controllers

available (sold separately).

Ordering Information

Connectors

*1. Flat Cable Connectors have one polarity slot.

*2. These Plugs and Sockets are made by Honda Tsushin Kogyo.

Accessories (Order Separately)

Connecting Cables for Connector-Terminal Block Conversion Units

For details on the Connecting Cable used between XW2B Daisy Chain-type Connectors, refer to the XW2Z datasheet.

Type Terminal Block Connector No. of poles Appearance Model

Flat Cable

Terminal block with

M3 screws

Flat Cable Connectors

20 XW2B-20G4

34 XW2B-34G4

40 XW2B-40G4

50 XW2B-50G4

60 XW2B-60G4

Terminal block with

M3.5 screws

20 XW2B-20G5

34 XW2B-34G5

40 XW2B-40G5

50 XW2B-50G5

60 XW2B-60G5

Twin-connector

Terminal block with

M3.5 screws

40 XW2B-40G5-T

Daisy Chain 20 XW2B-20G5-D

Multi-pole, Square

Connector

Terminal block with

M3 screws

Multi-pole, Square Connector

Plugs

20 XW2B-20Y4

34 XW2B-34Y4

50 XW2B-50Y4

Terminal block with

M3.5 screws 50 XW2B-50Y5

XW2B

Ratings and Specifications

Dimensions (Unit: mm)

Flat Cable Units with a Terminal Block with M3 Screws

Applicable Connectors

*1. Either the XG5M-@@32-N or the XG5M-@@35-N may be used.

*2. Each Connector requires two Semi-covers.

Type

Item

XW2B-@@G@

Flat Cable Units

XW2B-@@Y@

Multi-pole, Square-connector Units

XW2B-40F5-P

Board I/O Unit

Rated current 1 A

Rated voltage 125 VAC

Insulation resistance 100 MΩ min. (at 500 VDC)

Dielectric strength 500 VAC for 1 min (leakage current: 1 mA max.)

Ambient operating

temperature 0 to 55°C

Model

Applicable Connectors (order separately)

Flat Cable Connectors, MIL Sockets with

Strain Reliefs

Discrete-wire IDC Connectors, Double-row Sockets

Connectors *1 Semi-covers *2

XW2B-20G4 XG4M-2030-T XG5M-2032-N

XG5M-2035-N XG5S-1001

XW2B-34G4 XG4M-3430-T XG5M-3432-N

XG5M-3435-N XG5S-1701

XW2B-40G4 XG4M-4030-T XG5M-4032-N

XG5M-4035-N XG5S-2001

XW2B-50G4 XG4M-5030-T XG5M-5032-N

XG5M-5035-N XG5S-2501

XW2B-60G4 XG4M-6030-T XG5M-6032-N

XG5M-6035-N XG5S-3001

Flat Cable

Connector

(mating side)

Terminal Block

(terminal side)

N-3

N-2

N-1

N-2

N-1

N-3

Triangular mark

Flat Cable Connector (MIL Plug)

3.5

15.5

Two,

3.5 dia.

Terminal Block

3.5

29.5

5.08

20.5

DIN Track lock

38.1

(45.3)

XW2B-@@G4

Wiring Diagram

Dimensions

*Flat Cable Connectors have one polarity slot.

Note: Terminal block pitch is 5.08 mm.

Use a wire size between 0.3 and 1.25 mm2 (AWG22 to AWG16).

The wire insertion holes are 1.8 × 2.5 (H × W) mm.

Model No. of poles Dimension A (mm) Applicable Connector models *1

XW2B-20G4 20 67.5 XG4A-2031

XW2B-34G4 34 112.5 XG4A-3431

XW2B-40G4 40 135.0 XG4A-4031

XW2B-50G4 50 157.5 XG4A-5031

XW2B-60G4 60 180.0 XG4A-6031

Note: All pins on the Flat Cable Connector correspond

1-to-1 to the terminal of the same number on the

terminal block as shown above.

XW2B

Flat Cable Units with a Terminal Block with M3.5 Screws

Applicable Connectors

*1. Either the XG5M-@@32-N or the XG5M-@@35-N may be used.

*2. Each Connector requires two Semi-covers.

Model

Applicable Connectors (order separately)

Flat Cable Connectors, MIL Sockets with

Strain Reliefs

Discrete-wire IDC Connectors, Double-row Sockets

Connectors *1 Semi-covers *2

XW2B-20G5 XG4M-2030-T XG5M-2032-N

XG5M-2035-N XG5S-1001

XW2B-34G5 XG4M-3430-T XG5M-3432-N

XG5M-3435-N XG5S-1701

XW2B-40G5 XG4M-4030-T XG5M-4032-N

XG5M-4035-N XG5S-2001

XW2B-50G5 XG4M-5030-T XG5M-5032-N

XG5M-5035-N XG5S-2501

XW2B-60G5 XG4M-6030-T XG5M-6032-N

XG5M-6035-N XG5S-3001

Flat Cable Connector (MIL Plug)

3.5

15.5

Two,

3.5 dia.

Terminal

Block

7.3

8.5

29.5

3.5

(45.3)

43.5

20.5

DIN Track lock

Triangular mark

Flat Cable

Connector

(mating side)

Terminal Block

(terminal side)

N-3

N-2

N-1

N-2

N-1

N-3

XW2B-@@G5

Wiring Diagram

Dimensions

*Flat Cable Connectors have one polarity slot.

Note: Terminal block pitch is 8.5 mm.

Model No. of poles Dimension A (mm) Applicable Connector models *

XW2B-20G5 20 112.5 XG4A-2031

XW2B-34G5 34 180.0 XG4A-3431

XW2B-40G5 40 202.5 XG4A-4031

XW2B-50G5 50 247.5 XG4A-5031

XW2B-60G5 60 292.5 XG4A-6031

Note: All pins on the Flat Cable Connector correspond

1-to-1 to the terminal of the same number on the

terminal block as shown above.

XW2B

Twin-connector Units with a Terminal Block with M3.5 Screws

Applicable Connectors

*1. Either the XG5M-@@32-N or the XG5M-@@35-N may be used.

*2. Each Connector requires two Semi-covers.

Model

Applicable Connectors (order separately)

Flat Cable Connectors, MIL Sockets with

Strain Reliefs

Discrete-wire IDC Connectors, Double-row Sockets

Connectors *1 Semi-covers *2

XW2B-40G5-T XG4M-2030-T XG5M-2032-N

XG5M-2035-N XG5S-1001

Flat Cable Connector (MIL Plug: XG4A-2031 × 2)

3.5

15.5

Two,

3.5 dia.

Terminal Block

7.38.5

29.5

3.5

DIN Track lock

220.5

43.8 (45.3)

202.5

Triangular mark Triangular

mark

Flat Cable

Connector

(mating side)

Terminal Block

(terminal side)

4022

XW2B-40G5-T

Wiring Diagram

Note: All pins on the Flat Cable Connector correspond 1-to-1 to the terminal of

the same number on the terminal block as shown above.

XW2B

Daisy Chain Units with a Terminal Block with M3.5 Screws

Applicable Connectors

*1. Either the XG5M-@@32-N or the XG5M-@@35-N may be used.

*2. Each Connector requires two Semi-covers.

Model

Applicable Connectors (order separately)

Flat Cable Connectors, MIL Sockets with

Strain Reliefs

Discrete-wire IDC Connectors, Double-row Sockets

Connectors *1 Semi-covers *2

XW2B-20G5-D XG4M-2030-T XG5M-2032-N

XG5M-2035-N XG5S-1001

Flat Cable Connector (MIL Plug: XG4A-2031 × 2)

3.5

135

3.5

29.5

8.5

7.3

Terminal Block

15.5

Two,

3.5 dia.

(45.3)

43.8

20.5

DIN Track lock

Triangular mark

Flat Cable

Connector

(mating side)

Terminal Block

(terminal side)

XW2B-20G5-D

Wiring Diagram

Note: All pins on the Flat Cable Connector correspond 1-to-1 to the terminal

of the same number on the terminal block as shown above.

XW2B

Multi-pole, Square-connector Plug Units with a Terminal Block with M3 Screws

Applicable Connectors

*1. All applicable Connector Hoods are made by Honda Tsushin Kogyo.

*2. Use MRP-F113 or MRP-F103 crimp terminals made by Honda Tsushin Kogyo.

Model Applicable Connectors *1 Hood *1

XW2B-20Y4

MR-20F (soldered)

MRP-20F01 (crimped) *2

MR-20FW (wrapped)

MR-20L

XW2B-34Y4

MR-34F (soldered)

MRP-34F01 (crimped) *2

MR-34FW (wrapped)

MR-34L

XW2B-50Y4

MR-50F (soldered)

MRP-50F01 (crimped) *2

MR-50FW (wrapped)

MR-50L

Multi-contact,

Square Connector

(mating side)

Terminal Block

(terminal side)

Multi-contact Connector (Plug)

3.5

15.5

Two,

3.5 dia.

Terminal Block

3.5

29.5

DIN Track lock

220.5

38.1

5.08

XW2B-@@Y4

Wiring Diagram (Example for Terminal

Block with 50 Poles)

Dimensions

*These Connectors are made by Honda Tsushin Kogyo.

Note: Terminal block pitch is 5.08 mm.

Use a wire size between 0.3 and 1.25 mm2 (AWG22 to AWG16).

The wire insertion holes are 1.8 × 2.5 (H × W) mm.

Model No. of poles Dimension A (mm) Applicable Connector

models *

XW2B-20Y4 20 67.5 MR-20RMD2

XW2B-34Y4 34 112.5 MR-34RMD2

XW2B-50Y4 50 157.5 MR-50RMD2

Note: All pins on the Multi-pole, Square Connector correspond 1-to-

1 to the terminal of the same number on the terminal block as

shown above.

XW2B

Multi-pole, Square-connector Plug Units with a Terminal Block with M3.5 Screws

Applicable Connectors

*1. All applicable Connector Hoods are made by Honda Tsushin Kogyo.

*2. Use MRP-F113 or MRP-F103 crimp terminals made by Honda Tsushin Kogyo.

Model Applicable Connectors *1 Hood *1

XW2B-50Y5

MR-50F (soldered)

MRP-50F01 (crimped) *2

MR-50FW (wrapped)

MR-50L

Multi-contact,

Square Connector

(mating side)

Terminal Block

(terminal side)

3.5

29.5

Multi-contact, Square Connector (Plug)

A3.5

15.5

Two,

3.5 dia.

43.8

20.5

DIN Track lock

8.5 7.3 Terminal Block

XW2B-50Y5

Wiring Diagram (Example for Terminal

Block with 50 Poles)

Dimensions

*These Connectors are made by Honda Tsushin Kogyo.

Note: Terminal block pitch is 8.5 mm.

Model No. of

poles

Dimension A

(mm)

Applicable Connector

models *

XW2B-50Y5 50 247.5 MR-50RMD2

Note: All pins on the Multi-pole, Square Connector correspond

1-to-1 to the terminal of the same number on the terminal

block as shown above.

XW2B

Multi-pole, Square Connector Socket Units with a Terminal Block with M3.5 Screws

Applicable Connectors

*1. All applicable Connector Hoods are made by Honda Tsushin Kogyo.

*2. Use MRP-F113 or MRP-F103 crimp terminals made by Honda Tsushin Kogyo.

Model Applicable Connectors *1 Hood *1

XW2B-20X5

MR-20M (soldered)

MRP-20M01 (crimped) *2

MR-20MW (wrapped)

MR-20L

XW2B-34X5

MR-34M (soldered)

MRP-34M01 (crimped) *2

MR-34MW (wrapped)

MR-34L

XW2B-50X5

MR-50M (soldered)

MRP-50M01 (crimped) *2

MR-50MW (wrapped)

MR-50L

Multi-contact,

Square Connector

(mating side)

Terminal Block

(terminal side)

3.5

29.5

8.5 7.3 Terminal Block

Two,

3.5 dia.

15.5

3.5

Multi-contact, Square Connector (Socket)

DIN Track lock

220.5

43.8

XW2B-@@X5

Wiring Diagram (Example for

Terminal Block with 50 Poles)

Dimensions

*These Connectors are made by Honda Tsushin Kogyo.

Note: Terminal block pitch is 8.5 mm.

Model No. of poles Dimension A (mm) Applicable Connector models *

XW2B-20X5 20 112.5 MR-20RFD2

XW2B-34X5 34 180.0 MR-34RFD2

XW2B-50X5 50 247.5 MR-50RFD2

Note: All pins on the Multi-pole, Square Connector correspond 1-

to-1 to the terminal of the same number on the terminal

block as shown above.

XW2B

Board I/O Units with a Terminal Block with M3.5 Screws

Applicable Connectors

*1. All applicable Connectors and Covers are made by Fujitsu component.

*2. Refer to the OMNUC U Series user's manual for details on the Connecting Cable used between the XW2B-40F5-P and the U-series AC Servo Driver.

Model Applicable Connectors *1 Hood *1

XW2B-40F5-P FCN361J040-AU (soldered)

FCN363J040-AAU (crimped)

FCN360C040-

FCN-364P040-AU Plug

(mating side)

Terminal Block

(terminal side)

2019

3937

4038

I/O Board Connectors (40-pin Plug)

202.5

M2.6

3.5

29.5

8.5

7.3

Terminal Block

15.5

Two,

3.5 dia.

3.5

220.5

43.8

DIN Track lock

XW2B-40F5-P

Wiring Diagram Dimensions

*These Connectors and circuits are made by Fujitsu component.

Note: Terminal block pitch is 8.5 mm.

Model No. of poles Applicable Connectors and Circuits *

XW2B-40F5-P 40 FCN-364P40-AU (Connector)

FCN-360A1 (Anchor)

XW2B

Safety Precautions

●Wiring

•Always turn OFF the power supply before wiring.

Otherwise, cables or other conductors can short the

terminals and cause the Unit to fail.

•Do not connect or disconnect Connectors with the power

turned ON. Otherwise, it may cause malfunctions.

●Wiring Terminal Blocks

•Direct Wire Connections with a Terminal Block with M3

Screws

1. Use a wire size between 0.3 and 1.25 mm2 (AWG22 to

AWG16).

2. Prepare the end of each wire as shown in the following

diagram.

3. The wire insertion holes are 1.8 × 2.5 (H × W) mm on the

terminal block with M3 screws.

•Direct Wire Connections with a Terminal Block with M3.5

Screws

(With a Terminal Block with M3 Screws)

Note: Round rod and blade crimp terminals are made by Nichifu.

●Terminal Screw Tightening Torque

•Select a tightening torque from the following table when

connecting wires or crimp terminals to the terminal block.

●Mounting Units to and Removing Units from DIN Track

•For terminal blocks with M3 screws, use a flat-heat

screwdriver like the one shown in the following diagram.

•XW2B Connector-Terminal Block Conversion Units can be

mounted side-to-side on DIN Track. The flanges for

mounting screws are located on each side at the bottom of

the XW2B.

•Secure both ends of the XW2B with End Plates.

•When removing the Unit from a DIN Track, insert a flat-head

screwdriver into the slider and pull the lock out.

Precautions for Correct Use

Applicable crimp terminals Applicable wires

Round

1.25-3.5 AWG22 to AWG16

(0.30 to 1.25 mm2)

2-3.5 AWG16 to AWG14

(1.25 to 2.0 mm2)

Forked

1.25Y-3.5 AWG22 to AWG16

(0.30 to 1.25 mm2)

2Y-3.5 AWG16 to AWG14

(1.25 to 2.0 mm2)

Applicable crimp terminals Applicable wires

Rod

TC-05

Dia. = 1

AWG22 to AWG18

(0.30 to 0.75 mm2)

TC-1.25S

Dia. = 1.5

AWG22 to AWG16

(0.30 to 1.25 mm2)

Blade

BT1.25-9-1

BT1.25-10-1

W = 2.2

AWG22 to AWG16

(0.30 to 1.25 mm2)

6 mm

6.8

mm max.

3.7

mm dia.

6.8

mm max.

3.7

Round Forked

Dia.

t = 0.75

Round rod Blade

Terminal Block Tightening torque

N⋅m

With M3 screws 0.40

With M3.5 screws 0.59

2.9- to 3.5-mm blade

Screw slot width: 0.7

Terms and Conditions Agreement

Read and understand this catalog.

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you

have any questions or comments.

Warranties.

(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship

for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron

disclaims all other warranties, express or implied.

(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT

NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER

ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE

PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.

Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the

Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at

Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or

replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount

equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty,

repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products

were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate

modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall

not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or

electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice,

recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above

warranty.

See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,

LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,

WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.

Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.

Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the

combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable

third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself

is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine,

system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product

with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.

NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE

QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,

AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE

OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.

Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence

thereof.

Performance Data.

Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining

suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate

it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.

Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our

practice to change part numbers when published ratings or features are changed, or when significant construction changes are

made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers

may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at

any time to confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is

assumed for clerical, typographical or proofreading errors or omissions.

2017.6

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/