CONDUCTIVE POLYMER TANTALUM SOLID ELECTROLYTIC CAPACITORS
F31 Conductive Polymer Resin-molded Chip,
Compact Series
Specifications
Type numbering system (Example : 6.3V 47µF)
Dimensions
(mm)
Case code
P
LW1W2HS
2.0±0.2 1.25±0.1 0.9±0.1 1.1±0.1 0.5±0.2
A3.2±0.2 1.6±0.2 1.2±0.1 1.1±0.1 0.8±0.2
B3.4±0.2 2.8±0.2 2.3±0.1 1.1±0.1 0.8±0.2
L
H
S
W1
W2
S
Conductive
Polymer
Conductive Polymer
P Case
Capacitance
code
Rated
Voltage
code
Ja
Capacitance
code
A Case
Month
code
Rated
Voltage
code
Jar
Rated Capacitance ( F)
Rated Voltage (6.3V is marked as "6V")
Month code
33
P6v
B Case
Marking
F31 J0 4 7 6 MBA
123 546
78 91011
Rated Capacitance
Capacitance tolerance
Case code
Rated voltage
Series
Taping code
(Refer to page 302 for details)
Item Performance Characteristics
Category Temperature Range
Capacitance Tolerance
Dissipation Factor(at 120Hz)
ESR (100kHz)
Leakage Current
Ripple Current
Damp Heat
(Steady State)
Temperature Cycles
Resistance
to Soldering Heat
Surge
Endurance 1
Endurance 2
Shear Test
Terminal Strength
Ð55 to +105ûC (Rated temperature + 85ûC)
±20% (120Hz)
Refer to the list below
Refer to the list below
After 5 minutes' application of rated voltage, leakage current at
20ûC is not more than 0.1CV
At 60ûC, 90 to 95% R.H. 500hours (No voltage applied)
Ð55ûC / +105ûC 30 minutes each 5 cycle
Test Condition;10 second reflow at 240ûC
Capacitance Change..Within Ð20 to +30% of initial value
Dissipation Factor.......1.5 times Initial specified value or less
Leakage Current.........Initial specified value or less
Capacitance Change..Within ±20% of initial value
Dissipation Factor.......Initial specified value or less
Leakage Current.........Initial specified value or less
Capacitance Change..Within ±20% of initial value
Dissipation Factor.......1.3 times Initial specified value or less
Leakage Current.........Initial specified value or less
After application of surge voltage in series with a 1k½ resistor at
the rate of 30 seconds ON, 30 seconds OFF, for 1000 successive
test cycles at 85ûC, capacitors meet the characteristics
requirements listed below.
Capacitance Change...Within ±20% of initial value
Dissipation Factor........Initial specified value or less
Leakage Current..........Initial specified value or less
After 1000 hours' application of rated voltage in series with a 3½
resistor at 85ûC.
Capacitance Change....Within ±20% of initial value
Dissipation Factor...1.5 times Initial specified value or less
Leakage Current...Initial specified value or less
After 1000 hours' application of rated voltage in series with a 3½
resistor at 105ûC,capacitors meet the characteristic requirements
listed below
Capacitance Change....Within ±20% of initial value
Dissipation Factor...3 times Initial specified value or less
Leakage Current...Initial specified value or less
After applying the pressure load of 5N for 10±1 seconds
horizontally to the center of capacitor side body which has no
electrode and has been soldered beforehand
on an aluminum substrate, there shall be
found neither exfoliation nor its sign at the
terminal electrode.
Keeping a capacitor surface-mounted on a substrate upside
down and supporting the substrate at both of the opposite
bottom points 45mm apart from the center of the capacitor,
the pressure strength is applied with
a specified jig at the center of the
substrate so that the substrate may
bend by 1mm as illustrated. Then,
there shall be found no remarkable
abnormality on the capacitor terminals.
Refer to the list below
5N (0.51kg ¥f)
For 10±1 seconds
20
R230
45 45
1
mm
Adapted to the RoHS directive (2002/95/EC).
∗As for the surge voltage refer to page 301 for details.
()
The series in parentheses are being developed.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
10 106
22 226
33 336
47 476
68 686
100 107
P
A
A
B
P
P
A
(A)¥B
B
P
(P) ¥ A
(A)¥B
B
B
(B)
A
(A)¥B
2.5
0E
4
0G
6.3
0J
10
Capacitance
code
1A
B
B
a
n
s
Cap.
(µF) Code
V
Standard ratings
22
33
47
100
10
22
33
47
100
10
22
33
47
68
10
22
33
47
P
A
A
B
P
P
A
B
B
P
A
B
B
B
A
B
B
B
F310E226MPA
F310E336MAA
F310E476MAA
F310E107MBA
F310G106MPA
F310G226MPA
F310G336MAA
F310G476MBA
F310G107MBA
F310J106MPA
F310J226MAA
F310J336MBA
F310J476MBA
F310J686MBA
F311A106MAA
F311A226MBA
F311A336MBA
F311A476MBA
5.5
8.3
11.8
25.0
4.0
8.8
13.2
18.8
40.0
6.3
13.9
20.8
29.6
42.8
10.0
22.0
33.0
47.0
6
6
6
8
6
6
6
8
8
6
6
8
8
8
6
8
8
8
200
150
150
70
200
200
150
70
70
200
200
70
70 (55)
70
200
70
70
70
354
632
632
1035
354
354
632
1035
1035
354
548
1035
1035
1035
548
1035
1035
1035
Rated Volt
(V)
2.5
4
6.3
10
Part Number
Case
code
Rated
Capacitance
(
µ
F)
Leakage
Current
(
µ
A)
Disspation
Factor
(%@120Hz)
ESR
(m½@100kHz)
Rated Ripple
(mArms@100kHz)
() S f
()
E
S
R speci
f
ication types are also available upon request.
Please contact to your local Nichicon sales office when
these series are being designed in your application.
Standard ratings
µ
CAT.8100X
