DESIGNED & DIMENSIONED IN MILLIMETERS[INCHES] REVISION K BEC5-XXX-XX-X-X-V-A-XX-TR "A" REF DO NOT SCALE FROM THIS PRINT "C" REF 10.76 .424 REF 1.00 .039 REF PIN 02 "D" REF "A" 9.00 .354 REF 'B' PIN 01 "E" (SEE NOTE 8) PACKAGING -TR: TAPE & REEL No OF POSITIONS -060, -080, -100, -120, -140, -160, -180, -200 (SEE NOTE 6) CARD THICKNESS -02 (1.57mm [.062] PCB) (USE SUB-IM-C-270-02-X-X) -03 (2.36 mm [0.93] PCB) (USE SUB-IM-C-270-03-X-X) "B" REF OPTIONS -K: POLYIMIDE FILM (SEE FIG. 2, SHT 2) ALIGNMENT PINS -A: ALIGMENT PINS VERTICAL PLATING SPECIFICATION -L: 10 " SELECTIVE GOLD, MATTE TIN ON TAIL (USE SUB-IM-C-270-XX-L-X) -S: 30 " SELECTIVE GOLD, MATTE TIN ON TAILS (USE SUB-IM-C-270-XX-S-X) "A" C C BEC5-XXX-XX-V-XX 13.00 .512 REF SEE NOTE 5 1.18 .046 2.43 .096 REF PIN 04 (TOP) SUB-IM-C-270-XX-X-X (SEE NOTE 11) "F" (SEE NOTE 9) WT-16-04-T 1.86 .073 (2 PLCS) C 1.32 .052 REF C 1.000 .039 (TYP) NON ACCUM 0.51 .020 (TYP) TOL NON-ACCUM PIN 04 (TOP) PIN 03 (BOTTOM) "C" C SOLDER COMPOSTION & STYLE C -1: 63% TIN / 37% LEAD CHARGE TAIL (USE SUB-IM-C-270-XX-X-1) -2: 96.5% TIN / 3.5% SILVER LEAD FREE CHARGE TAIL (USE SUB-IM-C-270-XX-X-2) PIN 03 (BOTTOM) "C" PIN 01 (TOP) PIN 02 (BOTTOM) DETAIL 'B' SCALE 4 : 1 1.32 .052 REF SECTION "C"-"C" NOTES: CL 6.00 .236 0.64 .025 REF (TYP) C 1.10 .043 REF "J"0.20 "H" REF FIG 1 BEC5-140-02-X-X-V-A SHOWN C SCALE 4 : 1 1. C REPRESENTS A CRITICAL DIMENSION. 2. MINIMUM PUSHOUT FORCE: 2.22N[.5 LB]. 3. PARTS TO BE PACKAGED IN TAPE AND REEL AS STANDARD 4. FOR QUANTITIES UP TO 49 PIECES, NO LEADER, TRAILER OR REEL WILL BE SUPPLIED FOR QUANTITIES OF 50-124, NO LEADER OR TRAILER WILL BE SUPPLIED 5. SOLDER CRIMP VOLUME IS .20058 MM (0.000012691 IN) 6. NUMBER OF POSITIONS EQUALS TOTAL NUMBER OF CIRCUITS. 7. THESE INSIDE EDGES ARE NOT TO APPEAR IN THE WINDOW WHEN VIEWED FROM DIRECTLY ABOVE. 8. DIMENSION TAKEN BETWEEN TOP AND BOTTOM PINS. 9. CHECK TO THE LEAD AND NOT THE SOLDER CRIMP. 10. SEE DOCUMENT CO-OP-WI-3001-M FOR ADDITIONAL INSTRUCTION. 11. TO CALCULATE NUMBER OF SUBS NEEDED TAKE THE NUMBER OF POSITIONS AND DIVIDE BY 4. 12. MEASURE THIS DIMENSION AT ALL 4 CORNERS UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS [INCHS] TOLERANCES ARE: DECIMALS ANGLES X.X: 0.3 [.01] 2 X.XX: 0.13 [.005] X.XXX: 0.051 [.0020] MATERIAL: PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING INSULATOR: LCP , COLOR BLACK CONTACT: BeCu SHEET SCALE: 2:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail info@SAMTEC.com code 55322 DESCRIPTION: BI-LEVEL EDGE CARD ASSEMBLY DWG. NO. BEC5-XXX-XX-X-X-V-A-XX-TR F:\DWG\MISC\MKTG\BEC5-XXX-XX-X-X-V-A-XX-TR-MKT.SLDDRW BY: M MURILLO 1/16/2009 SHEET 1 OF 2 C REVISION K "A" REF "G"0.10 SEE NOTE 7 C 2.41 .095 REF "K"0.50[.020] CL CL 0.380.50 .015.020 8.25 .325 C 9.55 .376 REF 13.18 .519 7.14 .281 C FIG 2 -K: POLYIMIDE PAD (USE K-DOT-.325-.450-.005) (BEC5-140-02-X-X-V-A-K SHOWN) 2.29 .090 REF C +0.08 +.003 0.05 - 0.05 .002 - .002 (SEE NOTE 12) BEC5-XXX-XX-V-XX 0.15 .006 C 1.25 .049 WT-16-04-T SUB-IM-C-270-XX-X-X 1.27 .050 C "L"0.10 SECTION "A"-"A" SCALE 7 : 1 K PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING SHEET SCALE: 2:1 F:\DWG\MISC\MKTG\BEC5-XXX-XX-X-X-V-A-XX-TR-MKT.SLDDRW 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail info@SAMTEC.com code 55322 DESCRIPTION: BI-LEVEL EDGE CARD ASSEMBLY DWG. NO. BEC5-XXX-XX-X-X-V-A-XX-TR BY: M MURILLO 1/16/2009 SHEET 2 OF 2