TPS2062/TPS2066
D ANDDGNPACKAGE
(TOP VIEW)
AllEnableInputs Are ActiveHighForTPS2065,TPS2066,andTPS2067
1
GND
TPS2063/TPS2067
DPACKAGE
(TOP VIEW)
TPS2061/TPS2065
D ANDDGNPACKAGE
(TOP VIEW)
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
IN1
GND
IN2
NC
OC1
OUT1
OUT2
OUT3
NC
NC
GND
IN
IN
OUT
OUT
OUT
GND
IN
OC1
OUT1
OUT2
OC2
OC3
OC2
OC
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
EN3
EN
EN1
EN1
EN2
EN2
GND
OUT
TPS2061/TPS2065
DBVPACKAGE
(TOP VIEW)
IN
OC EN
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
CURRENT-LIMITED, POWER-DISTRIBUTION SWITCHES
Check for Samples: TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
1FEATURES APPLICATIONS
Heavy Capacitive Loads
2 70-mHigh-Side MOSFET Short-Circuit Protections
1-A Continuous Current
Thermal and Short-Circuit Protection
Accurate Current Limit
(1.1 A min, 1.9 A max)
Operating Range: 2.7 V to 5.5 V
0.6-ms Typical Rise Time
Undervoltage Lockout
Deglitched Fault Report (OC)
No OC Glitch During Power Up
1-μA Maximum Standby Supply Current
Bidirectional Switch
Ambient Temperature Range: -40°C to 85°C
Built-in Soft-Start
UL Listed - File No. E169910
DESCRIPTION
The TPS206x power-distribution switches are intended for applications where heavy capacitive loads and
short-circuits are likely to be encountered. This device incorporates 70-mN-channel MOSFET power switches
for power-distribution systems that require multiple power switches in a single package. Each switch is controlled
by a logic enable input. Gate drive is provided by an internal charge pump designed to control the power-switch
rise times and fall times to minimize current surges during switching. The charge pump requires no external
components and allows operation from supplies as low as 2.7 V.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2PowerPAD is a trademark of Texas Instruments.
UNLESS OTHERWISE NOTED this document contains Copyright © 2003–2009, Texas Instruments Incorporated
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
DESCRIPTION (CONTINUED)
When the output load exceeds the current-limit threshold or a short is present, the device limits the output current
to a safe level by switching into a constant-current mode, pulling the overcurrent (OCx) logic output low. When
continuous heavy overloads and short-circuits increase the power dissipation in the switch, causing the junction
temperature to rise, a thermal protection circuit shuts off the switch to prevent damage. Recovery from a thermal
shutdown is automatic once the device has cooled sufficiently. Internal circuitry ensures that the switch remains
off until valid input voltage is present. This power-distribution switch is designed to set current limit at 1.5 A
typically.
AVAILABLE OPTION AND ORDERING INFORMATION
RECOMMEND TYPICAL PACKAGED
ED SHORT- DEVICES (1)
MAXIMUM CIRCUIT NUMBER OF
TAENABLE CONTINUOUS CURRENT SWITCHES MSOP (DGN) SOIC (D) SOT23 (DBV) (2)
LOAD LIMIT
CURRENT AT 25°C
Active low TPS2061DGN TPS2061D -
Single
Active high TPS2065DGN TPS2065D -
Active low TPS2062DGN TPS2062D -
Dual
Active high TPS2066DGN TPS2066D -
-40°C to 85°C 1 A 1.5 A
Active low - TPS2063D -
Triple
Active high - TPS2067D -
Active low - - TPS2061DBV
Single
Active high - - TPS2065DBV
(1) The package is available taped and reeled. Add an R suffix to device types (e.g., TPS2062DR).
(2) The printed circuit board layout is important for control of temperature rise when operated at high ambient temperatures.
spacer
ORDERING INFORMATION
TASOIC(D) (1) STATUS MSOP (DGN) (1) STATUS SOT23 (DBV) (2) STATUS
TPS2061DG4 Active TPS2061DGNG4 Active - -
TPS2062DG4 Active TPS2062DGNG4 Active - -
TPS2065DG4 Active TPS2065DGNG4 Active - -
-40°C to 85°C TPS2066DG4 Active TPS2066DGNG4 Active - -
- - - - TPS2061DBV Active
- - - - TPS2065DBV Active
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
(2) The printed circuit board layout is important for control of temperature rise when operated at high ambient temperatures.
2Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range unless otherwise noted(1)
UNIT
Input voltage range, VI(IN) (2) -0.3 V to 6 V
Output voltage range, VO(OUT) (2), VO(OUTx) -0.3 V to 6 V
Input voltage range, VI(EN), VI(EN), VI(ENx), VI(ENx) -0.3 V to 6 V
Voltage range, VI(OC), VI(OCx) -0.3 V to 6 V
Continuous output current, IO(OUT), IO(OUTx) Internally limited
Continuous total power dissipation See Dissipation Rating Table
Operating virtual junction temperature range, TJ-40°C to 150°C
Human body model 2 kV
Electrostatic discharge (ESD) protection Charge device model (CDM) 500 V
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to GND.
DISSIPATING RATING TABLE
TA25°C DERATING FACTOR TA= 70°C TA= 85°C
PACKAGE POWER RATING ABOVE TA= 25°C POWER RATING POWER RATING
D-8(1) 585.82 mW 5.8582 mW/°C 322.20 mW 234.32 mW
DGN-8(2) 1712.3 mW 17.123 mW/°C 941.78 mW 684.33 mW
D-16(1) 898.47 mW 8.9847 mW/°C 494.15 mW 359.38 mW
285 mW 2.85 mW/°C 155 mW 114 mW
DBV-5(3) 704 mW 7.04 mW/°C 387 mW 281 mW
(1) Power ratings are based on the low-k board (1 signal, 1 layer).
(2) Power ratings are based on the high-k board (2 signal, 2 plane) with PowerPAD™ vias to the internal ground plane.
(3) Lower ratings are for low-k printed circuit board layout (single -sided). Higher ratings are for enhanced high-k layout, (2 signal, 2 plane)
with a 1mm2copper pad on pin 2 and 2 vias to the ground plane.
RECOMMENDED OPERATING CONDITIONS MIN MAX UNIT
Input voltage, VI(IN) 2.7 5.5 V
Input voltage, VI(EN), VI(EN), VI(ENx), VI(ENx) 0 5.5 V
Continuous output current, IO(OUT), IO(OUTx) 0 1 A
Operating virtual junction temperature, TJ-40 125 °C
ELECTRICAL CHARACTERISTICS
over recommended operating junction temperature range, VI(IN) = 5.5 V, IO= 1 A, VI(ENx) = 0 V, or VI(ENx) = 5.5 V (unless
otherwise noted)
PARAMETER TEST CONDITIONS (1) MIN TYP MAX UNIT
POWER SWITCH
Static drain-source on-state
resistance, 5-V operation VI(IN) = 5 V or 3.3 V, IO= 1 A, -40°C TJ125°C 70 135 m
and 3.3-V operation
rDS(on) Static drain-source on-state
resistance, 2.7-V VI(IN) = 2.7 V, IO= 1 A, -40°C TJ125°C 75 150 m
operation
VI(IN) = 5.5 V 0.6 1.5
trRise time, output VI(IN) = 2.7 V 0.4 1
CL= 1 μF, RL= 5 , TJ= 25°C ms
VI(IN) = 5.5 V 0.05 0.5
tfFall time, output VI(IN) = 2.7 V 0.05 0.5
(1) Pulse-testing techniques maintain junction temperature close to ambient temperature; thermal effects must be taken into account
separately.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
over recommended operating junction temperature range, VI(IN) = 5.5 V, IO= 1 A, VI(ENx) = 0 V, or VI(ENx) = 5.5 V (unless
otherwise noted)
PARAMETER TEST CONDITIONS (1) MIN TYP MAX UNIT
ENABLE INPUT EN OR EN
VIH High-level input voltage 2.7 V VI(IN) 5.5 V 2 V
VIL Low-level input voltage 2.7 V VI(IN) 5.5 V 0.8
IIInput current VI(ENx) = 0 V or 5.5 V, VI(ENx) = 0 V or 5.5 V -0.5 0.5 μA
ton Turnon time CL= 100 μF, RL= 5 3ms
toff Turnoff time CL= 100 μF, RL= 5 10
CURRENT LIMIT
TJ= 25°C 1.1 1.5 1.9
VI(IN) = 5 V, OUT connected to GND,
IOS Short-circuit output current A
device enabled into short-circuit -40°C TJ125°C 1.1 1.5 2.1
TPS2061, TPS2062, 1.6 2.3 2.7
TPS2065, TPS2066
IOC_TRIP Overcurrent trip threshold VI(IN) = 5 V, current ramp (100 A/s) on OUT A
TPS2063, TPS2067 1.6 2.4 3.0
SUPPLY CURRENT (TPS2061, TPS2065)
TJ= 25°C 0.5 1
No load on OUT, VI(ENx) = 5.5 V,
Supply current, low-level output μA
or VI(ENx) = 0 V -40°C TJ125°C 0.5 5
TJ= 25°C 43 60
No load on OUT, VI(ENx) = 0 V,
Supply current, high-level output μA
or VI(ENx) = 5.5 V -40°C TJ125°C 43 70
OUT connected to ground, VI(EN) = 5.5 V,
Leakage current -40°C TJ125°C 1 μA
or VI(EN) = 0 V
Reverse leakage current VI(OUTx) = 5.5 V, IN = ground TJ= 25°C 0 μA
SUPPLY CURRENT (TPS2062, TPS2066)
TJ= 25°C 0.5 1
No load on OUT, VI(ENx) = 5.5 V,
Supply current, low-level output μA
or VI(ENx) = 0 V -40°C TJ125°C 0.5 5
TJ= 25°C 50 70
No load on OUT, VI(ENx) = 0 V,
Supply current, high-level output μA
or VI(ENx) = 5.5 V -40°C TJ125°C 50 90
OUT connected to ground, VI(/ENx) = 5.5 V,
Leakage current -40°C TJ125°C 1 μA
or VI(ENx) = 0 V
Reverse leakage current VI(OUTx) = 5.5 V, IN = ground TJ= 25°C 0.2 μA
SUPPLY CURRENT (TPS2063, TPS2067)
TJ= 25°C 0.5 2
Supply current, low-level output No load on OUT, VI(ENx) = 0 V μA
-40°C TJ125°C 0.5 10
TJ= 25°C 65 90
Supply current, high-level output No load on OUT, VI(ENx) = 5.5 V μA
-40°C TJ125°C 65 110
OUT connected to ground, VI(ENx) = 5.5 V,
Leakage current -40°C TJ125°C 1 μA
or VI(ENx) = 0 V
Reverse leakage current VI(OUTx) = 5.5 V, INx = ground TJ= 25°C 0.2 μA
UNDERVOLTAGE LOCKOUT
Low-level input voltage, IN 2 2.5 V
Hysteresis, IN TJ= 25°C 75 mV
OVERCURRENT OC1 and OC2
Output low voltage, VOL(OCx) IO(OCx) = 5 mA 0.4 V
Off-state current VO(OCx) = 5 V or 3.3 V 1 μA
OC deglitch OCx assertion or deassertion 4 8 15 ms
THERMAL SHUTDOWN(2)
Thermal shutdown threshold 135 °C
Recovery from thermal shutdown 125 °C
Hysteresis 10 °C
(2) The thermal shutdown only reacts under overcurrent conditions.
4Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
OUT
OC
IN
EN
GND
Current
Limit
Driver
UVLO
Charge
Pump
CS
Thermal
Sense Deglitch
Note A: Current sense
Note B: Active low (EN) for TPS2061. Active high (EN) for TPS2065.
(See Note A)
(See Note B)
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
DEVICE INFORMATION
Pin Functions (TPS2061 and TPS2065)
PINS
D or DGN Package DBV Package I/O DESCRIPTION
NAME TPS2061 TPS2065 TPS2061 TPS2065
EN 4 - 4 - I Enable input, logic low turns on power switch
EN - 4 - 4 I Enable input, logic high turns on power switch
GND 1 1 2 2 Ground
IN 2, 3 2,3 5 5 I Input voltage
OC 5 5 3 3 O Overcurrent, open-drain output, active-low
OUT 6, 7, 8 6, 7, 8 1 1 O Power-switch output
Internally connected to GND; used to heat-sink the part
PowerPAD™ - - - - to the circuit board traces. Should be connected to GND
pin.
Functional Block Diagram
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
Thermal
Sense
Driver Current
Limit
Charge
Pump
UVLO
CS
Driver Current
Limit
CS
Thermal
Sense
Charge
Pump
GND
EN1
IN
EN2
OC1
OUT1
OUT2
OC2
Deglitch
Deglitch
(See Note A)
(See Note A)
(See Note B)
(See Note B)
Note A: Current sense
Note B: Active low (ENx) for TPS2062. Active high (ENx) for TPS2066.
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
Pin Functions (TPS2062 and TPS2066)
PINS I/O DESCRIPTION
NAME NO.
TPS2062 TPS2066
EN1 3 - I Enable input, logic low turns on power switch IN-OUT1
EN2 4 - I Enable input, logic low turns on power switch IN-OUT2
EN1 - 3 I Enable input, logic high turns on power switch IN-OUT1
EN2 - 4 I Enable input, logic high turns on power switch IN-OUT2
GND 1 1 Ground
IN 2 2 I Input voltage
OC1 8 8 O Overcurrent, open-drain output, active low, IN-OUT1
OC2 5 5 O Overcurrent, open-drain output, active low, IN-OUT2
OUT1 7 7 O Power-switch output, IN-OUT1
OUT2 6 6 O Power-switch output, IN-OUT2
Internally connected to GND; used to heat-sink the part to the circuit board traces.
PowerPAD™ - - Should be connected to GND pin.
Functional Block Diagram
6Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
Pin Functions (TPS2063 and TPS2067)
PINS I/O DESCRIPTION
NAME TPS2063 TPS2067
EN1 3 I Enable input, logic low turns on power switch IN1-OUT1
EN2 4 I Enable input, logic low turns on power switch IN1-OUT2
EN3 7 I Enable input, logic low turns on power switch IN2-OUT3
EN1 3 I Enable input, logic high turns on power switch IN1-OUT1
EN2 4 I Enable input, logic high turns on power switch IN1-OUT2
EN3 7 I Enable input, logic high turns on power switch IN2-OUT3
GND 1, 5 1, 5 Ground
IN1 2 2 I Input voltage for OUT1 and OUT2
IN2 6 6 I Input voltage for OUT3
NC 8, 9, 10 8, 9, 10 No connection
OC1 16 16 O Overcurrent, open-drain output, active low, IN1-OUT1
OC2 13 13 O Overcurrent, open-drain output, active low, IN1-OUT2
OC3 12 12 O Overcurrent, open-drain output, active low, IN2-OUT3
OUT1 15 15 O Power-switch output, IN1-OUT1
OUT2 14 14 O Power-switch output, IN1-OUT2
OUT3 11 11 O Power-switch output, IN2-OUT3
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
Thermal
Sense
Driver Current
Limit
UVLO CS
Driver Current
Limit
CS
Thermal
Sense
GND
EN1
IN1
EN2
OC1
OUT1
OUT2
OC2
Deglitch
Deglitch
Driver Current
Limit
CS
Thermal
Sense
Charge
Pump
GND
IN2
EN3
OUT3
OC3
Deglitch
VCC
Selector
UVLO
(See Note A)
Note A: Current sense
Note B: Active low (ENx) for TPS2063; Active high (ENx) for TPS2067
(See Note A)
(See Note A)
(See Note B)
(See Note B)
(See Note B)
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
Functional Block Diagram
8Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
RLCL
OUT
trtf
90% 90%
10%
10%
50% 50%
90%
10%
VO(OUT)
VI(EN)
VO(OUT)
VOLTAGE WAVEFORMS
TEST CIRCUIT
ton toff
50% 50%
90%
10%
VI(EN)
VO(OUT)
ton toff
VI(EN)
5 V/div
VO(OUT)
2 V/div
RL = 5 W,
CL = 1 mF
TA = 255C
t − Time − 500 ms/div
VI(EN)
5 V/div
VO(OUT)
2 V/div
RL = 5 W,
CL = 1 mF
TA = 255C
t − Time − 500 ms/div
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
PARAMETER MEASUREMENT INFORMATION
Figure 1. Test Circuit and Voltage Waveforms
Figure 2. Turnon Delay and Rise Time With 1-μF Figure 3. Turnoff Delay and Fall Time With 1-μF
Load Load
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
VI(EN)
5 V/div
VO(OUT)
2 V/div
RL = 5 W,
CL = 100 mF
TA = 255C
t − Time − 500 ms/div
VO(OUT)
2 V/div
VI(EN)
5 V/div
RL = 5 W,
CL = 100 mF
TA = 255C
t − Time − 500 ms/div
VI(EN)
5 V/div
IO(OUT)
500 mA/div
470 mF
100 mF
220 mF
VIN = 5 V
RL = 5 W,
TA = 255C
t − Time − 1 ms/div
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 4. Turnon Delay and Rise Time With 100-μF Figure 5. Turnoff Delay and Fall Time With 100-μF
Load Load
Figure 6. Short-Circuit Current, Figure 7. Inrush Current With Different
Device Enabled Into Short Load Capacitance
10 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
VO(OC)
2 V/div
IO(OUT)
1 A/div
t − Time − 2 ms/div
VO(OC)
2 V/div
IO(OUT)
1 A/div
t − Time − 2 ms/div
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
23456
Turnon Time − ms
VI − Input Voltage − V
CL = 100 mF,
RL = 5 W,
TA = 255C
1.5
1.6
1.7
1.8
1.9
2
2 3 4 5 6
CL = 100 mF,
RL = 5 W,
TA = 255C
Turnoff Time − mS
VI − Input Voltage − V
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
PARAMETER MEASUREMENT INFORMATION (continued)
Figure 8. 2-Load Connected to Enabled Device Figure 9. 1-Load Connected to Enabled Device
TYPICAL CHARACTERISTICS
TURNON TIME TURNOFF TIME
vs vs
INPUT VOLTAGE INPUT VOLTAGE
Figure 10. Figure 11.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
0
0.1
0.2
0.3
0.4
0.5
0.6
2 3 4 5 6
Rise Time − ms
VI − Input Voltage − V
CL = 1 mF,
RL = 5 W,
TA = 255C
0
0.05
0.1
0.15
0.2
0.25
2 3 4 5 6
CL = 1 mF,
RL = 5 W,
TA = 255C
Fall Time − ms
VI − Input Voltage − V
0
10
20
30
40
50
60
−50 0 50 100 150
VI = 5.5 V
VI = 3.3 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Enabled −
II (IN) Aµ
VI = 5 V
0
10
20
30
40
50
60
70
−50 0 50 100 150
VI = 5.5 V
VI = 5 V
VI = 3.3 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Enabled −
II (IN) Aµ
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
RISE TIME FALL TIME
vs vs
INPUT VOLTAGE INPUT VOLTAGE
Figure 12. Figure 13.
TPS2061, TPS2065 TPS2062, TPS2066
SUPPLY CURRENT, OUTPUT ENABLED SUPPLY CURRENT, OUTPUT ENABLED
vs vs
JUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 14. Figure 15.
12 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
0
10
20
30
40
50
60
70
80
90
−50 0 50 100 150
VI = 5.5 V
VI = 5 V
VI = 3.3 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Enabled −
II (IN) Aµ
TJ − Junction Temperature − 5C
− Supply Current, Output Disabled −II (IN) Aµ
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
−50 0 50 100 150
VI = 2.7 V VI = 3.3 V
VI = 5.5 V
VI = 5 V
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
−50 0 50 100 150
VI = 5.5 V VI = 5 V
VI = 3.3 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Disabled −
II (IN) Aµ
0
0.05
0.1
0.15
0.2
0.25
0.3
0.35
0.4
0.45
0.5
−50 0 50 100 150
VI = 5.5 V
VI = 5 V
VI = 2.7 V
TJ − Junction Temperature − 5C
− Supply Current, Output Disabled −
II (IN) Aµ
VI = 3.3 V
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
TPS2063, TPS2067 TPS2061, TPS2065
SUPPLY CURRENT, OUTPUT ENABLED SUPPLY CURRENT, OUTPUT DISABLED
vs vs
JUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 16. Figure 17.
TPS2062, TPS2066 TPS2063, TPS2067
SUPPLY CURRENT, OUTPUT DISABLED SUPPLY CURRENT, OUTPUT DISABLED
vs vs
JUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 18. Figure 19.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
1.34
1.36
1.38
1.4
1.42
1.44
1.48
1.5
1.52
1.54
1.56
−50 0 50 100 150
1.46
VI = 3.3 V
VI = 5 V
VI = 3.3 V
VI = 5.5 V
TJ − Junction Temperature − 5C
− Short-Circuit Output Current − A
IOS
VI = 2.7 V
0
20
40
60
80
100
120
−50 0 50 100 150
Out1 = 5 V
Out1 = 3.3 V
Out1 = 2.7 V
IO = 0.5 A
TJ − Junction Temperature − 5C
rDS(on) − Static Drain-Source
On-State Resistance − m
2.1
2.14
2.18
2.22
2.26
2.3
−50 0 50 100 150
UVLO Rising
UVLO Falling
UVOL − Undervoltage Lockout − V
TJ − Junction Temperature − 5C
1.5
1.7
1.9
2.1
2.3
2.5
2.5 3 3.5 4 4.5 5 5.5 6
TA = 255C
Load Ramp = 1A/10 ms
Threshold Trip Current − A
VI − Input Voltage − V
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
TYPICAL CHARACTERISTICS (continued)
STATIC DRAIN-SOURCE ON-STATE RESISTANCE SHORT-CIRCUIT OUTPUT CURRENT
vs vs
JUNCTION TEMPERATURE JUNCTION TEMPERATURE
Figure 20. Figure 21.
THRESHOLD TRIP CURRENT UNDERVOLTAGE LOCKOUT
vs vs
INPUT VOLTAGE JUNCTION TEMPERATURE
Figure 22. Figure 23.
14 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
0
50
100
150
200
0 2.5 5 7.5 10 12.5
Current-Limit Response − sµ
Peak Current − A
VI = 5 V,
TA = 255C
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
TYPICAL CHARACTERISTICS (continued)
CURRENT-LIMIT RESPONSE
vs
PEAK CURRENT
Figure 24.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
IN
OC1
EN1
OC2
2
8
5
7
0.1 µF22 µF
0.1 µF22 µF
Load
Load
OUT1
OUT2
Power Supply
2.7 V to 5.5 V
6
EN2
3
4
GND
0.1 µF
TPS2062
1
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
APPLICATION INFORMATION
POWER-SUPPLY CONSIDERATIONS
Figure 25. Typical Application
A 0.01-μF to 0.1-μF ceramic bypass capacitor between IN and GND, close to the device, is recommended.
Placing a high-value electrolytic capacitor on the output pin(s) is recommended when the output load is heavy.
This precaution reduces power-supply transients that may cause ringing on the input. Additionally, bypassing the
output with a 0.01-μF to 0.1-μF ceramic capacitor improves the immunity of the device to short-circuit transients.
OVERCURRENT
A sense FET is employed to check for overcurrent conditions. Unlike current-sense resistors, sense FETs do not
increase the series resistance of the current path. When an overcurrent condition is detected, the device
maintains a constant output current and reduces the output voltage accordingly. Complete shutdown occurs only
if the fault is present long enough to activate thermal limiting.
Three possible overload conditions can occur. In the first condition, the output has been shorted before the
device is enabled or before VI(IN) has been applied (see Figure 15). The TPS206x senses the short and
immediately switches into a constant-current output.
In the second condition, a short or an overload occurs while the device is enabled. At the instant the overload
occurs, high currents may flow for a short period of time before the current-limit circuit can react. After the
current-limit circuit has tripped (reached the overcurrent trip threshold), the device switches into constant-current
mode.
In the third condition, the load has been gradually increased beyond the recommended operating current. The
current is permitted to rise until the current-limit threshold is reached or until the thermal limit of the device is
exceeded (see Figure 18). The TPS206x is capable of delivering current up to the current-limit threshold without
damaging the device. Once the threshold has been reached, the device switches into its constant-current mode.
OC RESPONSE
The OCx open-drain output is asserted (active low) when an overcurrent or overtemperature shutdown condition
is encountered after a 10-ms deglitch timeout. The output remains asserted until the overcurrent or
overtemperature condition is removed. Connecting a heavy capacitive load to an enabled device can cause a
momentary overcurrent condition; however, no false reporting on OCx occurs due to the 10-ms deglitch circuit.
The TPS206x is designed to eliminate false overcurrent reporting. The internal overcurrent deglitch eliminates
the need for external components to remove unwanted pulses. OCx is not deglitched when the switch is turned
off due to an overtemperature shutdown.
16 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
GND
IN
EN1
EN2
OC1
OC2
OUT1
OUT2
TPS2062 Rpullup
V+
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
Figure 26. Typical Circuit for the OC Pin
POWER DISSIPATION AND JUNCTION TEMPERATURE
The low on-resistance on the N-channel MOSFET allows the small surface-mount packages to pass large
currents. The thermal resistances of these packages are high compared to those of power packages; it is good
design practice to check power dissipation and junction temperature. Begin by determining the rDS(on) of the
N-channel MOSFET relative to the input voltage and operating temperature. As an initial estimate, use the
highest operating ambient temperature of interest and read rDS(on) from Figure 20. Using this value, the power
dissipation per switch can be calculated by:
PD= rDS(on)× I2
Multiply this number by the number of switches being used. This step renders the total power dissipation from
the N-channel MOSFETs.
The thermal resistance, RθJA = 1 / (DERATING FACTOR), where DERATING FACTOR is obtained from the
Dissipation Ratings Table. Thermal resistance is a strong function of the printed circuit board construction , and
the copper trace area connecting the integrated circuit.
Finally, calculate the junction temperature:
TJ= PDx RθJA + TA
Where:
TA= Ambient temperature °C
RθJA = Thermal resistance
PD= Total power dissipation based on number of switches being used.
Compare the calculated junction temperature with the initial estimate. If they do not agree within a few degrees,
repeat the calculation, using the calculated value as the new estimate. Two or three iterations are generally
sufficient to get a reasonable answer.
THERMAL PROTECTION
Thermal protection prevents damage to the IC when heavy-overload or short-circuit faults are present for
extended periods of time. The TPS206x implements a thermal sensing to monitor the operating junction
temperature of the power distribution switch. In an overcurrent or short-circuit condition, the junction temperature
rises due to excessive power dissipation. Once the die temperature rises above a minimum of 135°C due to
overcurrent conditions, the internal thermal sense circuitry turns the power switch off, thus preventing the power
switch from damage. Hysteresis is built into the thermal sense circuit, and after the device has cooled
approximately 10°C, the switch turns back on. The switch continues to cycle in this manner until the load fault or
input power is removed. The OCx open-drain output is asserted (active low) when an overtemperature shutdown
or overcurrent occurs.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
UNDERVOLTAGE LOCKOUT (UVLO)
An undervoltage lockout ensures that the power switch is in the off state at power up. Whenever the input
voltage falls below approximately 2 V, the power switch is quickly turned off. This facilitates the design of
hot-insertion systems where it is not possible to turn off the power switch before input power is removed. The
UVLO also keeps the switch from being turned on until the power supply has reached at least 2 V, even if the
switch is enabled. On reinsertion, the power switch is turned on, with a controlled rise time to reduce EMI and
voltage overshoots.
UNIVERSAL SERIAL BUS (USB) APPLICATIONS
The universal serial bus (USB) interface is a 12-Mb/s, or 1.5-Mb/s, multiplexed serial bus designed for
low-to-medium bandwidth PC peripherals (e.g., keyboards, printers, scanners, and mice). The four-wire USB
interface is conceived for dynamic attach-detach (hot plug-unplug) of peripherals. Two lines are provided for
differential data, and two lines are provided for 5-V power distribution.
USB data is a 3.3-V level signal, but power is distributed at 5 V to allow for voltage drops in cases where power
is distributed through more than one hub across long cables. Each function must provide its own regulated 3.3 V
from the 5-V input or its own internal power supply.
The USB specification defines the following five classes of devices, each differentiated by power-consumption
requirements:
Hosts/self-powered hubs (SPH)
Bus-powered hubs (BPH)
Low-power, bus-powered functions
High-power, bus-powered functions
Self-powered functions
SPHs and BPHs distribute data and power to downstream functions. The TPS206x has higher current capability
than required by one USB port; so, it can be used on the host side and supplies power to multiple downstream
ports or functions.
HOST/SELF-POWERED AND BUS-POWERED HUBS
Hosts and SPHs have a local power supply that powers the embedded functions and the downstream ports (see
Figure 27). This power supply must provide from 5.25 V to 4.75 V to the board side of the downstream
connection under full-load and no-load conditions. Hosts and SPHs are required to have current-limit protection
and must report overcurrent conditions to the USB controller. Typical SPHs are desktop PCs, monitors, printers,
and stand-alone hubs.
18 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
IN
OC1
EN1
OC2
EN2
GND
0.1 µF
2
8
3
5
4
7
33 µF
33 µF
GND
1
OUT1
TPS2062
Power Supply
D+
D−
VBUS
GND
D+
D−
VBUS
Downstream
USB Ports
USB
Controller
3.3 V 5 V
33 µFGND
OUT2
D+
D−
VBUS
33 µFGND
D+
D−
VBUS
6
0.1 µF
0.1 µF
0.1 µF
0.1 µF
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
Figure 27. Typical Four-Port USB Host / Self-Powered Hub
BPHs obtain all power from upstream ports and often contain an embedded function. The hubs are required to
power up with less than one unit load. The BPH usually has one embedded function, and power is always
available to the controller of the hub. If the embedded function and hub require more than 100 mA on power up,
the power to the embedded function may need to be kept off until enumeration is completed. This can be
accomplished by removing power or by shutting off the clock to the embedded function. Power switching the
embedded function is not necessary if the aggregate power draw for the function and controller is less than one
unit load. The total current drawn by the bus-powered device is the sum of the current to the controller, the
embedded function, and the downstream ports, and it is limited to 500 mA from an upstream port.
LOW-POWER BUS-POWERED AND HIGH-POWER BUS-POWERED FUNCTIONS
Both low-power and high-power bus-powered functions obtain all power from upstream ports; low-power
functions always draw less than 100 mA; high-power functions must draw less than 100 mA at power up and can
draw up to 500 mA after enumeration. If the load of the function is more than the parallel combination of 44
and 10 μF at power up, the device must implement inrush current limiting (see Figure 28). With TPS206x, the
internal functions could draw more than 500 mA, which fits the needs of some applications such as motor driving
circuits.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
IN
OC1
OC2
2
8
3
5
4
7
0.1 µF10 µFInternal
Function
OUT1
Power Supply
3.3 V
EN1
6
0.1 µF10 µF
OUT2 Internal
Function
0.1 µF
10 µF
USB
Control
GND
VBUS
D−
D+ TPS2062
EN2 GND
1
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
Figure 28. High-Power Bus-Powered Function
USB POWER-DISTRIBUTION REQUIREMENTS
USB can be implemented in several ways, and, regardless of the type of USB device being developed, several
power-distribution features must be implemented.
Hosts/SPHs must:
Current-limit downstream ports
Report overcurrent conditions on USB VBUS
BPHs must:
Enable/disable power to downstream ports
Power up at <100 mA
Limit inrush current (<44 and 10 μF)
Functions must:
Limit inrush currents
Power up at <100 mA
The feature set of the TPS206x allows them to meet each of these requirements. The integrated current-limiting
and overcurrent reporting is required by hosts and self-powered hubs. The logic-level enable and controlled rise
times meet the need of both input and output ports on bus-powered hubs, as well as the input ports for
bus-powered functions (see Figure 29).
20 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
DP1
DM1
DP2
DM2
DP3
DM3
DP4
PWRON1
OVRCUR1
PWRON2
OVRCUR2
DM4
DP0
DM0
VCC
XTAL1
XTAL2
OCSOFF
SN75240
D +
D −
5 V
GND
D +
D −
5 V
D +
D −
5 V
D +
D −
5 V
48-MHz
Crystal
Downstream
Ports
TUSB2040
Hub Controller
Tuning
Circuit
A
BC
D
33 µF
SN75240
A
BC
D
GND
GND
GND
33 µF
33 µF
33 µF
D +
D −
Upstream
Port
TPS2041B
SN75240
A
B
5 V
GND
C
D
1 µF
IN
GND
Ferrite Beads
Ferrite Beads
Ferrite Beads
Ferrite Beads
BUSPWR
GANGED
Tie to TPS2041 EN Input
OC EN
OUT
5-V Power
Supply
IN
GND
3.3 V
4.7 µF
0.1 µF
4.7 µF
EN1
IN
OC1
OUT1
TPS2062
EN2
OC2
OUT2
0.1 µF
GND
USB rev 1.1 requires 120 µF per hub.
TPS76333
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
Figure 29. Hybrid Self / Bus-Powered Hub Implementation
GENERIC HOT-PLUG APPLICATIONS
In many applications it may be necessary to remove modules or pc boards while the main unit is still operating.
These are considered hot-plug applications. Such implementations require the control of current surges seen by
the main power supply and the card being inserted. The most effective way to control these surges is to limit and
slowly ramp the current and voltage being applied to the card, similar to the way in which a power supply
normally turns on. Due to the controlled rise times and fall times of the TPS206x, these devices can be used to
provide a softer start-up to devices being hot-plugged into a powered system. The UVLO feature of the TPS206x
also ensures that the switch is off after the card has been removed, and that the switch is off during the next
insertion. The UVLO feature insures a soft start with a controlled rise time for every insertion of the card or
module.
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
Power
Supply
0.1 µF
1000 µF
Optimum
2.7 V to 5.5 V
PC Board
Overcurrent Response
TPS2062
OC1
GND
EN1
IN
EN2
OUT1
OUT2
OC2 Block of
Circuitry
Block of
Circuitry
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
Figure 30. Typical Hot-Plug Implementation
By placing the TPS206x between the VCC input and the rest of the circuitry, the input power reaches these
devices first after insertion. The typical rise time of the switch is approximately 1 ms, providing a slow voltage
ramp at the output of the device. This implementation controls system surge currents and provides a
hot-plugging mechanism for any device.
DETAILED DESCRIPTION
Power Switch
The power switch is an N-channel MOSFET with a low on-state resistance. Configured as a high-side switch, the
power switch prevents current flow from OUT to IN and IN to OUT when disabled. The power switch supplies a
minimum current of 1 A.
Charge Pump
An internal charge pump supplies power to the driver circuit and provides the necessary voltage to pull the gate
of the MOSFET above the source. The charge pump operates from input voltages as low as 2.7 V and requires
little supply current.
Driver
The driver controls the gate voltage of the power switch. To limit large current surges and reduce the associated
electromagnetic interference (EMI) produced, the driver incorporates circuitry that controls the rise times and fall
times of the output voltage.
Enable (ENx or ENx)
The logic enable disables the power switch and the bias for the charge pump, driver, and other circuitry to reduce
the supply current. The supply current is reduced to less than 1 μA when a logic high is present on ENx, or when
a logic low is present on ENx. A logic zero input on ENx, or a logic high input on ENx restores bias to the drive
and control circuits and turns the switch on. The enable input is compatible with both TTL and CMOS logic
levels.
Overcurrent (OCx)
The OCx open-drain output is asserted (active low) when an overcurrent or overtemperature condition is
encountered. The output remains asserted until the overcurrent or overtemperature condition is removed. A
10-ms deglitch circuit prevents the OCx signal from oscillation or false triggering. If an overtemperature shutdown
occurs, the OCx is asserted instantaneously.
22 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
www.ti.com
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
Current Sense
A sense FET monitors the current supplied to the load. The sense FET measures current more efficiently than
conventional resistance methods. When an overload or short circuit is encountered, the current-sense circuitry
sends a control signal to the driver. The driver in turn reduces the gate voltage and drives the power FET into its
saturation region, which switches the output into a constant-current mode and holds the current constant while
varying the voltage on the load.
Thermal Sense
The TPS206x implements a thermal sensing to monitor the operating temperature of the power distribution
switch. In an overcurrent or short-circuit condition the junction temperature rises. When the die temperature rises
to approximately 140°C due to overcurrent conditions, the internal thermal sense circuitry turns off the switch,
thus preventing the device from damage. Hysteresis is built into the thermal sense, and after the device has
cooled approximately 10 degrees, the switch turns back on. The switch continues to cycle off and on until the
fault is removed. The open-drain false reporting output (OCx) is asserted (active low) when an overtemperature
shutdown or overcurrent occurs.
Undervoltage Lockout
A voltage sense circuit monitors the input voltage. When the input voltage is below approximately 2 V, a control
signal turns off the power switch.
spacer
REVISION HISTORY
Changes from Original (December 2003) to Revision A Page
Added devices to the data sheet- TPS2063, TPS2065, TPS2066, TPS2067 ...................................................................... 1
Added the General Switch Catalog ....................................................................................................................................... 1
Changes from Revision A (July 2004) to Revision B Page
Changed Features Bullet From: UL Pending To: UL Listed - File No. E169910 .................................................................. 1
Changed Electrical Characteristics - CURRENT LIMIT information. .................................................................................... 4
Changes from Revision C (January 2006) to Revision D Page
Changed ORDERING INFORMATION table ........................................................................................................................ 2
Changes from Revision D (Februaty 2007) to Revision E Page
Changed General Switch Catalog information. ..................................................................................................................... 1
Changes from Revision E (September 2007) to Revision F Page
Added the DBV-5 package. .................................................................................................................................................. 1
Added the DBV-5 package option. ....................................................................................................................................... 1
Added the DBV-5 package option to the Dissipation Ratings table. .................................................................................... 3
Changed Thermal Sense paragraph: From: Once the die temperature rises to approximately 140°C To: Once the
die temperature rises above a minimum of 135°C ............................................................................................................. 17
Copyright © 2003–2009, Texas Instruments Incorporated Submit Documentation Feedback 23
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
TPS2061, TPS2062, TPS2063
TPS2065, TPS2066, TPS2067
SLVS490I DECEMBER 2003REVISED OCTOBER 2009
www.ti.com
Changes from Revision F (April 2008) to Revision G Page
Changed DBV-5 to Product Preview. ................................................................................................................................... 1
Changes from Revision G (July 2008) to Revision H Page
Deleted Product Preview from the DBV package ................................................................................................................. 1
Changed TPS2061DBV status From Preview to Active ....................................................................................................... 2
Changed TPS2065DBV status From Preview to Active ....................................................................................................... 2
Changes from Revision H (December 2008) to Revision I Page
Changed the ESD statement ................................................................................................................................................ 2
Deleted temp range of 0°C to 70°C from the Available Option table. .................................................................................. 2
Added Note to the Available Options table - The printed circuit board layout is important for control of temperature
rise when operated at high ambient temperatures ............................................................................................................... 2
Deleted temp range of 0°C to 70°C from the Ordering Information table. ............................................................................ 2
Added Note to the Ordering Information table - The printed circuit board layout is important for control of
temperature rise when operated at high ambient temperatures ........................................................................................... 2
Changed the Abs Max Ratings table - Operating virtual junction temperature range From: -40°C to 125°C To: -40°C
to 150°C ................................................................................................................................................................................ 3
Deleted Storage temperature range, Tstg from the Abs Max Ratings table .......................................................................... 3
Deleted MIL-STD-883C reference from ESD in the Abs Max table ..................................................................................... 3
Added 3 table notes to the Dissipation Ratings table. .......................................................................................................... 3
Added Addition values for the DBV-5 option in the Dissipation Ratings table. .................................................................... 3
Deleted Note - Not tested in production, specified by design from rDS(on) in the Electrical Characteristics table. ................ 3
Deleted Note - Not tested in production, specified by design from trin the Electrical Characteristics table. ....................... 3
Deleted Note - Not tested in production, specified by design from tfin the Electrical Characteristics table. ....................... 3
Added text to the POWER DISSIPATION section - The thermal resistance, RθJA ............................................................. 17
24 Submit Documentation Feedback Copyright © 2003–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS2061 TPS2062 TPS2063 TPS2065 TPS2066 TPS2067
PACKAGE OPTION ADDENDUM
www.ti.com 9-Aug-2011
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TPS2061D ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DGN ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DGNG4 ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DGNR ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DGNRG4 ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2061DRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062D ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062DG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062DGN ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062DGNG4 ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062DGNR ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062DGNRG4 ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2062DR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
PACKAGE OPTION ADDENDUM
www.ti.com 9-Aug-2011
Addendum-Page 2
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TPS2062DRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2063D ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2063DG4 ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2063DR ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2063DRG4 ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065D ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DBVR ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DBVT ACTIVE SOT-23 DBV 5 250 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DGN ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DGNG4 ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DGNR ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DGNRG4 ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2065DRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066D ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066DG4 ACTIVE SOIC D 8 75 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066DGN ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
PACKAGE OPTION ADDENDUM
www.ti.com 9-Aug-2011
Addendum-Page 3
Orderable Device Status (1) Package Type Package
Drawing Pins Package Qty Eco Plan (2) Lead/
Ball Finish MSL Peak Temp (3) Samples
(Requires Login)
TPS2066DGNG4 ACTIVE MSOP-
PowerPAD DGN 8 80 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066DGNR ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066DGNRG4 ACTIVE MSOP-
PowerPAD DGN 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066DR ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066DRG4 ACTIVE SOIC D 8 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2066ID PREVIEW SOIC D 8 TBD Call TI Call TI Add to cart
TPS2066IDR PREVIEW SOIC D 8 TBD Call TI Call TI Add to cart
TPS2067D ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2067DG4 ACTIVE SOIC D 16 40 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2067DR ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
TPS2067DRG4 ACTIVE SOIC D 16 2500 Green (RoHS
& no Sb/Br) CU NIPDAU Level-1-260C-UNLIM Add to cart
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
PACKAGE OPTION ADDENDUM
www.ti.com 9-Aug-2011
Addendum-Page 4
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS2062 :
Automotive: TPS2062-Q1
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
TPS2061DBVR SOT-23 DBV 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
TPS2061DBVT SOT-23 DBV 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
TPS2061DGNR MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1
TPS2061DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TPS2062DGNR MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
TPS2062DGNR MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1
TPS2062DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TPS2063DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
TPS2065DBVR SOT-23 DBV 5 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3
TPS2065DBVR SOT-23 DBV 5 3000 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
TPS2065DBVT SOT-23 DBV 5 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3
TPS2065DBVT SOT-23 DBV 5 250 179.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
TPS2065DGNR MSOP-
Power DGN 8 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 1
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
PAD
TPS2065DGNR MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
TPS2065DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TPS2066DGNR MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.3 1.3 8.0 12.0 Q1
TPS2066DGNR MSOP-
Power
PAD
DGN 8 2500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1
TPS2066DR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1
TPS2067DR SOIC D 16 2500 330.0 16.4 6.5 10.3 2.1 8.0 16.0 Q1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TPS2061DBVR SOT-23 DBV 5 3000 203.0 203.0 35.0
TPS2061DBVT SOT-23 DBV 5 250 203.0 203.0 35.0
TPS2061DGNR MSOP-PowerPAD DGN 8 2500 346.0 346.0 35.0
TPS2061DR SOIC D 8 2500 340.5 338.1 20.6
TPS2062DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0
TPS2062DGNR MSOP-PowerPAD DGN 8 2500 346.0 346.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 2
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
TPS2062DR SOIC D 8 2500 340.5 338.1 20.6
TPS2063DR SOIC D 16 2500 367.0 367.0 38.0
TPS2065DBVR SOT-23 DBV 5 3000 180.0 180.0 18.0
TPS2065DBVR SOT-23 DBV 5 3000 203.0 203.0 35.0
TPS2065DBVT SOT-23 DBV 5 250 180.0 180.0 18.0
TPS2065DBVT SOT-23 DBV 5 250 203.0 203.0 35.0
TPS2065DGNR MSOP-PowerPAD DGN 8 2500 346.0 346.0 35.0
TPS2065DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0
TPS2065DR SOIC D 8 2500 340.5 338.1 20.6
TPS2066DGNR MSOP-PowerPAD DGN 8 2500 346.0 346.0 35.0
TPS2066DGNR MSOP-PowerPAD DGN 8 2500 364.0 364.0 27.0
TPS2066DR SOIC D 8 2500 340.5 338.1 20.6
TPS2067DR SOIC D 16 2500 333.2 345.9 28.6
PACKAGE MATERIALS INFORMATION
www.ti.com 14-Jul-2012
Pack Materials-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated