DENSEI-LAMBDA PFE1000F SPECIFICATIONS C251-01-01B MODEL 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 ITEMS Nominal Output Voltage Maximum Output Current Maximum Output Power Efficiency (Typ.) Input Voltage Range Input Frequency Input Current Power Factor Output Voltage Accuracy Output Voltage Range Maximum Ripple & Noise Maximum Line Regulation Maximum Load Regulation Over Current Protection Over Voltage Protection In-rush Current (Typ.) Remote Sensing Remote ON/OFF Control Parallel Operation Series Operation Operating Temperature Operating Humidity Storage Temperature Storage Humidity Cooling Withstand Voltage (*1) PFE1000F-12 V A W % Hz A % % mV mV mV A - PFE1000F-28 12 60 720 80 / 82 PFE1000F-48 28 48 36 21 1008 1008 (*1) 84 / 86 84 / 86 (*2) (*3) 85 - 265 VAC (*2) 47 - 63 (*1) 9.8 / 4.8 13.6 / 6.6 13.4 / 6.5 (*1)(*3) 0.95 min +/-2 -20 / +20 (*3) 120 280 480 48 56 96 48 56 96 (*4)(*5) 105% - 140% (*5) 125% - 145% (Inverter shutdown method) (*1)(*3) 20A / 40A peak (*6) Possible (*6) Possible (*6) Possible (*6) Possible -40C - +100C(Baseplate) (*7)(*8) 20 - 95%RH (No Dewdrop) -40C - +100C 10 - 95%RH (No Dewdrop) (*9) Conduction Cooled Input-Baseplate : 2.5kVAC, Input-Output : 3.0kVAC for 1min. Output-Baseplate : 500VDC for 1min. 27 Isolation Resistance Output to Baseplate 500VDC more than 100M (25C,70%RH) 28 Vibration At no operating, 10-55Hz (Sweep for 1min.) 2 Amplitude 0.825mm constant (Maximum 49.0m/s ) X,Y,Z 1 hour each 2 29 Shock 196.1m/s 30 Safety Approved by UL60950-1, CSA60950-1, EN60950-1 31 Weight (Typ.) g 500 32 Size (W x H x D) mm 100 x 13.4 x 160 (Refer to Outline Drawing) * Read instruction manual carefully, before using the power module. =NOTES= *1. At 100VAC/200VAC and maximum output power. (Baseplate Temperature = +25C.) *2. For cases where conformance to various safety specs (UL, CSA, EN) are required, input voltage range will be 100 - 240VAC(50/60Hz). *3. External components are needed for operation. (Refer to basic connection and instruction manual.) *4. Constant current limiting. (The unit automatically shutdown when left in OCP condition, with the output voltage less than the LVP level. Refer to instruction manual.) *5. Reset : Line off or Control off. (Refer to instruction manual.) *6. Refer to Instruction manual. *7. Ambient Temperature min=-40C *8. Ratings - refer to Derating Curve (C251-01-02_). *9. Heatsink has to be chosen according to Instruction manual. DENSEI-LAMBDA PFE1000F C251-01-02A Derating Curve PFE1000F-12 (720W) 100 Load (%) 80 60 40 20 0 -40 -20 0 20 40 60 80 100 120 80 85 100 120 Baseplate temperature (C) PFE1000F-28,48 (1008W) 100 Load (%) 80 60 40 85VAC < Vin < 170VAC 170VAC < Vin < 265VAC 20 0 -40 -20 0 20 40 60 Baseplate temperature (C) DENSEI-LAMBDA PFE1000F C251-01-03 BASIC CONNECTION Measurement point for output ripple & noise. (JEITA RC-9131 B probe) Bandwidth of scope : 100MHz L= 50mm Measurement point for Vo load/ line regulation. L1 L2 INPUT C1 AC(L) +V C6 C4 C3 +S L3 C2 C5 R1 C7 C15 C8 *3 C16 *2,3 P F E1 0 0 0 F -V AC(N) -S TRIM AUX IOG PC BASE-PLATE ENA + ON/OFF -ON/OFF COM R +BC -BC C9 *2,3 C10 *2,3 C11 *4 TFR2 C12 *4 *5 TFR1 C13 *4 *5 C14 *4 F1 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 F25AH 250V AC250V 1uF (Film) 470pF 470pF AC250V 1uF (Film) AC250V 1uF (Film) 4700pF 4700pF AC250V 1uF (Film) 450V 1uF (Film) 450V 1uF (Film) 450V 390uF (Elec.) 450V 390uF (Elec.) 450V 390uF (Elec.) 450V 390uF (Elec.) C15 C16 0.033uF 0.033uF 12V: 25V 1000uF (Elec.) C17 28V: 50V 470uF (Elec.) 48V: 100V 220uF (Elec.) C18 100V 2.2uF (Ceramic) 12V: 25V 1000uF (Elec.) C19 28V: 50V 470uF (Elec.) 48V: 100V 220uF (Elec.) R1 0.5W 470k TFR1 5.1 139C (Res., Thermal fuse) TFR2 5.1 139C (Res., Thermal fuse) L1 2mH L2 2mH L3 2mH ==NOTES== *1. *2. *3. *4. Use an external fuse of fast blow type for each unit. The allowable ripple current of capacitor must be more than 3A(rms). Put this capacitor near the terminal as close as possible. The maximum capacitance that can be used is less than 2300uF(Rated capacitance). Avoid the connection of capacitance which is more than above, else it will lead to module to damage. *5. The inrush current at AC throw in can be suppressed by the external Resistor (Built-in thermal fuse) connected between the R and +BC terminals. *6. If the ambient temperature is less than -20C, use twice the recommended capacitor above. *7. Refer to instruction manual for further details. C17 C18 *6 C19 *6 OUTPUT F1 *1