LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
LM140L/LM340L Series 3-Terminal Positive Regulators
Check for Samples: LM140L,LM340L
1FEATURES The LM140LA/LM340LA are available in the low
2• Line Regulation of 0.04%/V profile metal three lead TO (NDT) and the LM340LA
• Load Regulation of 0.01%/mA are also available in the plastic TO-92 (LP). With
• Output Voltage Tolerances of adequate heat sinking the regulator can deliver 100
mA output current. Current limiting is included to limit
– ±2% at Tj= 25°C and ±4% Over the the peak output current to a safe value. Safe area
Temperature Range (LM140LA) protection for the output transistor is provided to limit
– ±3% Over the Temperature Range internal power dissipation. If internal power
(LM340LA) dissipation becomes too high for the heat sinking
• Output Current of 100 mA provided, the thermal shut-down circuit takes over,
preventing the IC from overheating.
• Internal Thermal Overload Protection
• Output Transistor Safe Area Protection For applications requiring other voltages, see LM117L
Data Sheet.
• Internal Short Circuit Current Limit
• Available in Output Voltage Options
– Metal TO Low Profile Package LM140LA-5.0 5V LM340LA-5.0 5V
(LM140LA/LM340LA) LM140LA-12 12V LM340LA-12 12V
– Plastic TO-92 (LM340LA)
LM140LA-15 15V LM340LA-15 15V
DESCRIPTION
The LM140L series of three terminal positive Connection Diagrams
regulators is available with several fixed output
voltages making them useful in a wide range of
applications. The LM140LA is an improved version of
the LM78LXX series with a tighter output voltage
tolerance (specified over the full military temperature
range), higher ripple rejection, better regulation and
lower quiescent current. The LM140LA regulators
have ±2% VOUT specification, 0.04%/V line regulation,
and 0.01%/mA load regulation. When used as a
zener diode/resistor combination replacement, the Figure 1. TO Metal Can Package (NDT)
LM140LA usually results in an effective output (Bottom View)
impedance improvement of two orders of magnitude,
and lower quiescent current. These regulators can
provide local on card regulation, eliminating the
distribution problems associated with single point
regulation. The voltages available allow the LM140LA
to be used in logic systems, instrumentation, Hi-Fi,
and other solid state electronic equipment. Although
designed primarily as fixed voltage regulators, these
devices can be used with external components to Figure 2. TO-92 Plastic Package (LP)
obtain adjustable voltages and currents. (Bottom View)
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 1998–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)(3)
Input Voltage 35V
Internal Power Dissipation(4) Internally Limited
LM140LA −55°C to +125°C
Operating Temperature Range LM340LA 0°C to +70°C
Maximum Junction Temperature +150°C
Metal Can (NDT package) −65°C to +150°C
Storage Temperature Range Molded TO-92 −55°C to +150°C
Metal Can +300°C
Lead Temperature (Soldering, 10 sec.) Plastic TO-92 +230°C
(1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not ensure specific performance limits.
(2) A military RETS specification is available upon request. At the time of printing, the LM140LA-5.0, -12, and -15 RETS specifications
complied with the Min and Max limits in this table. The LM140LAH-5.0, LM140LAH-12, and LM140LAH-15 may also be procured as
Standard Military Drawings.
(3) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
(4) Thermal resistance of NDT-package is typically 26°C/W θjC, 250°C/W θjA still air, and 94°C/W θjA 400 lf/min of air. For the LP-package is
60°C/W θjC, 232°C/W θjA still air, and 88°C/W θjA at 400 lf/min of air. The maximum junction temperature shall not exceed 125°C on
electrical parameters.
Electrical Characteristics
Test conditions unless otherwise specified. TA=−55°C to +125°C (LM140LA), TA= 0°C to +70°C (LM340LA), IO= 40 mA, CIN
= 0.33 μF, CO= 0.01 μF.
Output Voltage Option 5.0V 12V 15V
Input Voltage (unless otherwise noted) 10V 19V 23V Units
Symbol Parameter Conditions Min Typ Max Min Typ Max Min Typ Max
VOOutput Tj= 25°C 4.9 5 5.1 11.75 12 12.25 14.7 15 15.3
Voltage LM140LA IO= 1 −100 mA 4.8 5.2 11.5 12.5 14.4 15.6
(7.2–20) (14.5–27) (17.6–30) V
Output
Voltage Over LM340LA IO= 1 −100 mA or 4.85 5.15 11.65 12.35 14.55 15.45
Temp.(1) IO= 1 −40 mA and (7–20) (14.3–27) (17.5–30)
VIN = ( )V
ΔVOTj= 25°C IO= 40 mA 18 30 30 65 37 70
VIN = ( )V (7–25) (14.2–30) (17.3–30)
Line
Regulation IO= 100 mA 18 30 30 65 37 70 mV
VIN = ( )V (7.5–25) (14.5–30) (17.5–30)
Tj= 25°C IO= 1 −40 mA 5 20 10 40 12 50
Load
Regulation IO= 1 −100 mA 20 40 30 80 35 100 mV
Long Term 12 24 30 1000
Stability hrs
IOTj= 25°C 3 4.5 3 4.5 3.1 4.5
Quiescent mA
Current Tj= 125°C 4.2 4.2 4.2
ΔIQTj= 25°C ΔLoad IO= 1 −40 0.1 0.1 0.1
Quiescent mA
Current mA
ΔLine VIN = ( )V 0.5 0.5 0.5
Change (7.5–25) (14.3–30) (17.5–30)
(1) The temperature coefficient of VOUT is typically within 0.01% VO/°C.
2Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
Electrical Characteristics (continued)
Test conditions unless otherwise specified. TA=−55°C to +125°C (LM140LA), TA= 0°C to +70°C (LM340LA), IO= 40 mA, CIN
= 0.33 μF, CO= 0.01 μF.
Output Voltage Option 5.0V 12V 15V
Input Voltage (unless otherwise noted) 10V 19V 23V Units
Symbol Parameter Conditions Min Typ Max Min Typ Max Min Typ Max
VNOutput Noise Tj= 25°C(2), f = 10 Hz–10 kHz 40 80 90 μV
Voltage f = 120 Hz, VIN = ( )V 55 62 47 54 45 52
ΔVIN Ripple dB
ΔVout Rejection (7.5–18) (14.5–25) (17.5–28.5)
Input Voltage
Required to Tj= 25°C, IO= 40 mA 7 14.2 17.3 V
Maintain Line
Regulation
(2) It is recommended that a minimum load capacitor of 0.01 μF be used to limit the high frequency noise bandwidth.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM140L LM340L
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics
Maximum Average
Maximum Average Power Power Dissipation
Dissipation (Metal Can Package)
Figure 3. Figure 4.
Maximum Average Power
Dissipation (Plastic Package) Peak Output Current
Figure 5. Figure 6.
Dropout Voltage Output Impedance
Figure 7. Figure 8.
4Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
LM140L, LM340L
www.ti.com
SNVS758B –APRIL 1998–REVISED MARCH 2013
Typical Performance Characteristics (continued)
Ripple Rejection Quiescent Current
Figure 9. Figure 10.
Quiescent Current
Figure 11.
Copyright © 1998–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM140L LM340L
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
TYPICAL APPLICATIONS
*Required if the regulator is located far from the power supply filter.
**It is recommended that a minimum load capacitor of 0.01 μF be used to limit the high frequency noise bandwidth.
Figure 12. Fixed Output Regulator
VOUT = 5V + (5V/R1 + IO) R2
5V/R1 = 3 IOload regulation (L,) [(R1 + R2)/R1] (L, of LM140LA-5.0)
Figure 13. Adjustable Output Regulator
6Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
LM140L, LM340L
SNVS758B –APRIL 1998–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B Page
• Changed layout of National Data Sheet to TI format ............................................................................................................ 7
8Submit Documentation Feedback Copyright © 1998–2013, Texas Instruments Incorporated
Product Folder Links: LM140L LM340L
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM140LAH-12 ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) AU | Call TI Level-1-NA-UNLIM -55 to 125 ( LM140LAH-12, LM1
40LAH-12)
LM140LAH-12/NOPB ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) AU | Call TI Level-1-NA-UNLIM -55 to 125 ( LM140LAH-12, LM1
40LAH-12)
LM140LAH-15 ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) Call TI Level-1-NA-UNLIM -55 to 125 ( LM140LAH-15, LM1
40LAH-15)
LM140LAH-15/NOPB ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) AU | Call TI Level-1-NA-UNLIM -55 to 125 ( LM140LAH-15, LM1
40LAH-15)
LM140LAH-5.0 ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) AU | Call TI Level-1-NA-UNLIM -55 to 125 ( LM140LAH-5.0, LM
140LAH-5.0)
LM140LAH-5.0/NOPB ACTIVE TO NDT 3 500 Green (RoHS
& no Sb/Br) AU | Call TI Level-1-NA-UNLIM -55 to 125 ( LM140LAH-5.0, LM
140LAH-5.0)
LM340LAZ-5.0/LFT4 ACTIVE TO-92 LP 3 2000 Green (RoHS
& no Sb/Br) CU SN N / A for Pkg Type 340LA
Z-5.0
LM340LAZ-5.0/NOPB ACTIVE TO-92 LP 3 1800 Green (RoHS
& no Sb/Br) CU SN N / A for Pkg Type 0 to 70 340LA
Z-5.0
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
PACKAGE OPTION ADDENDUM
www.ti.com 24-Aug-2018
Addendum-Page 2
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
MECHANICAL DATA
NDT0003A
www.ti.com
H03A (Rev D)
www.ti.com
PACKAGE OUTLINE
3X 2.67
2.03
5.21
4.44
5.34
4.32
3X
12.7 MIN
2X 1.27 0.13
3X 0.55
0.38
4.19
3.17
3.43 MIN
3X 0.43
0.35
(2.54)
NOTE 3
2X
2.6 0.2
2X
4 MAX
SEATING
PLANE
6X
0.076 MAX
(0.51) TYP
(1.5) TYP
TO-92 - 5.34 mm max heightLP0003A
TO-92
4215214/B 04/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Lead dimensions are not controlled within this area.
4. Reference JEDEC TO-226, variation AA.
5. Shipping method:
a. Straight lead option available in bulk pack only.
b. Formed lead option available in tape and reel or ammo pack.
c. Specific products can be offered in limited combinations of shipping medium and lead options.
d. Consult product folder for more information on available options.
EJECTOR PIN
OPTIONAL
PLANE
SEATING
STRAIGHT LEAD OPTION
321
SCALE 1.200
FORMED LEAD OPTION
OTHER DIMENSIONS IDENTICAL
TO STRAIGHT LEAD OPTION
SCALE 1.200
www.ti.com
EXAMPLE BOARD LAYOUT
0.05 MAX
ALL AROUND
TYP
(1.07)
(1.5) 2X (1.5)
2X (1.07)
(1.27)
(2.54)
FULL R
TYP
( 1.4)0.05 MAX
ALL AROUND
TYP
(2.6)
(5.2)
(R0.05) TYP
3X ( 0.9) HOLE
2X ( 1.4)
METAL
3X ( 0.85) HOLE
(R0.05) TYP
4215214/B 04/2017
TO-92 - 5.34 mm max heightLP0003A
TO-92
LAND PATTERN EXAMPLE
FORMED LEAD OPTION
NON-SOLDER MASK DEFINED
SCALE:15X
SOLDER MASK
OPENING
METAL
2X
SOLDER MASK
OPENING
123
LAND PATTERN EXAMPLE
STRAIGHT LEAD OPTION
NON-SOLDER MASK DEFINED
SCALE:15X
METAL
TYP
SOLDER MASK
OPENING
2X
SOLDER MASK
OPENING
2X
METAL
12 3
www.ti.com
TAPE SPECIFICATIONS
19.0
17.5
13.7
11.7
11.0
8.5
0.5 MIN
TYP-4.33.7
9.75
8.50
TYP
2.9
2.4 6.75
5.95
13.0
12.4
(2.5) TYP
16.5
15.5
32
23
4215214/B 04/2017
TO-92 - 5.34 mm max heightLP0003A
TO-92
FOR FORMED LEAD OPTION PACKAGE
IMPORTANT NOTICE
Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its
semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers
should obtain the latest relevant information before placing orders and should verify that such information is current and complete.
TI’s published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated
circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and
services.
Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is
accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced
documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements
different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the
associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Buyers and others who are developing systems that incorporate TI products (collectively, “Designers”) understand and agree that Designers
remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have
full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products
used in or for Designers’ applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with
respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous
consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and
take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will
thoroughly test such applications and the functionality of such TI products as used in such applications.
TI’s provision of technical, application or other design advice, quality characterization, reliability data or other services or information,
including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, “TI Resources”) are intended to
assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any
way, Designer (individually or, if Designer is acting on behalf of a company, Designer’s company) agrees to use any particular TI Resource
solely for this purpose and subject to the terms of this Notice.
TI’s provision of TI Resources does not expand or otherwise alter TI’s applicable published warranties or warranty disclaimers for TI
products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections,
enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically
described in the published documentation for a particular TI Resource.
Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that
include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE
TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY
RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or
endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
TI RESOURCES ARE PROVIDED “AS IS” AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR
REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO
ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL
PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM,
INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF
PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL,
DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN
CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949
and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements.
Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such
products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards
and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must
ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in
life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use.
Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life
support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all
medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S.
TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product).
Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications
and that proper product selection is at Designers’ own risk. Designers are solely responsible for compliance with all legal and regulatory
requirements in connection with such selection.
Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer’s non-
compliance with the terms and provisions of this Notice.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2018, Texas Instruments Incorporated
