ITC135P Integrated Telecom Circuits Parameter Relay Blocking Voltage Relay Load Current Relay Max RON Bridge Rectifier Reverse Voltage Darlington Collector Current Darlington Current Gain Rating 350 120 15 100 120 10,000 Units V mA V mA - The ITC135's optocoupler provides for half-wave detection of ringing signals. Features * * * * * * * * * * * * Description This Integrated Telecom Circuit combines a single-pole, normally open (1-Form-A) solid state relay, a bridge rectifier, a Darlington transistor, an optocoupler, and Zener diodes into one 16-pin SOIC package, consolidating designs and reducing component count in telecom applications. 3750Vrms Input/Output Isolation FCC Compatible Part 68 2mW Hook Switch Drive Power (Logic Compatible) Full-Wave Bridge Rectifier Darlington Transistor for Electronic Inductor "Dry" Circuits Half-Wave Current Detector for Ring Signal or Loop Current Detect Includes Zener Diodes Board Space and Cost Savings No Moving Parts Small 16-Pin SOIC Package (PCMCIA Compatible) Tape & Reel Version Available JEDEC Standard Pin Out Applications * Data/Fax Modem * Voice Mail Systems * Telephone Sets * Computer Telephony Integration * Cable TV Modems Approvals * UL Recognized Component: File E76270 * CSA Certified Component: Certificate 1305490 * EN/IEC 60950-1 Certified Component: TUV Certificate: B 09 07 49410 006 Ordering Information Part # ITC135P ITC135PTR Description 16-Pin SOIC (50/Tube) 16-Pin SOIC (1000/Reel) Pin Configuration (N/C) - LED - Form A Relay - LED - Form A Relay + Zener Diode (cathode) - Zener Diode (anode) + Zener Diode (cathode) Collector - Phototransistor Emitter - Phototransistor * 1 16 2 15 PV 3 14 4 13 5 12 6 11 7 10 * 8 9 Output Form A Output Form A/Bridge Input -/+ Darlington Base Darlington Emitter Bridge Output +/Darlington Collector/ + Zener Diode (cathode) Bridge Output -/- Zener Diode (anode) LED - Phototransistor (+) LED - Phototransistor (-) Denotes reverse polarity protection diode; half-wave detection only. Switching Characteristics of Normally Open Devices Form-A IF 90% 10% ILOAD ton Pb RoHS 2002/95/EC DS-ITC135P-R04 toff e3 www.clare.com 1 ITC135P Absolute Maximum Ratings @ 25C Parameter Input Control Current, Relay Input Control Current, Detector Total Package Dissipation 1 Isolation Voltage, Input to Output Operational Temperature Storage Temperature 1 Ratings 50 100 1 3750 -40 to +85 -40 to +125 Units mA mA W Vrms C C Absolute Maximum Ratings are stress ratings. Stresses in excess of these ratings can cause permanent damage to the device. Functional operation of the device at conditions beyond those indicated in the operational sections of this data sheet is not implied. Derate linearly 8.33 mW / C Total Power Dissipation (PD): PD=PHOOKSWITCH + PBRIDGE + PDARLINGTON + PLED PD=(RDS(on)) (I2L) + 2(VF)(IL) + (VCE)(IL) + (VLED)(IF) WHERE: RDS(on) = Maximum relay on resistance IL = Maximum loop current VF = Maximum diode forward voltage VCE = Maximum voltage collector to emitter VLED = Maximum LED forward voltage IF = Maximum LED current Electrical Characteristics @ 25C: Relay Section Parameter Output Characteristics Blocking Voltage (Peak) Load Current Continuous Peak On-Resistance Off-State Leakage Current Switching Speeds Turn-On Turn-Off Output Capacitance Input Characteristics Input Control Current (to Activate) Input Voltage Drop Reverse Input Voltage Reverse Input Current Conditions Symbol Min Typ Max Units - VL - - 350 VP t=10ms IL=120mA VL=350V, TJ=25C IL ILPK RON ILEAK - - 120 400 15 1 VL=50V, f=1MHz ton toff COUT - 25 3 3 - IL=120mA IF=5mA VR=5V IF VF VR IR 0.9 - 1.2 - 5 1.4 5 10 IF=5mA, VL=10V mA A ms pF mA V V A Electrical Characteristics @25C: Darlington Transistor Section Parameter Collector-Emitter Voltage Collector Current, Continuous Power Dissipation Off-State Collector-Emitter Leakage Current DC Current Gain Saturation Voltage Total Harmonic Distortion 2 Conditions IC=10mADC, IB=0mA VC=3.5V VCE=10V, IB=0mA VCE=10VDC, IC=120mA IC=120mA IC=40mA, fO=300Hz @ -10dBm Symbol VCEO IC PD ICEX hFE VCE(sat) - www.clare.com Min 40 10,000 - Typ - Max 120 500 1 1.5 -80 Units V mA mW A V dB R04 ITC135P Electrical Characteristics @25C: Detector Section Parameter Output Characteristics Phototransistor Blocking Voltage Phototransistor Dark Current Saturation Voltage Current Transfer Ratio Input Characteristics Input Control Current Input Voltage Drop Input Current (Detector Must be Off) Conditions Symbol Min Typ Max Units IC=10A VCE=5V, IF=0mA IF=16mA , IC=2mA IF=6mA, VCE=0.5V BVCEO ICEO VSAT CTR 20 33 50 50 0.3 400 500 0.5 - V nA V % IC=2mA, VCE=0.5V IF=5mA IC=1A, VCE=5V IF VF IF 0.9 5 2 1.2 25 6 1.4 - mA V A Units V V Electrical Characteristics @25C (Unless Otherwise Noted): Bridge Rectifier Section Parameter Reverse Voltage Forward Voltage Drop Reverse Leakage Current Conditions IFD=120mA TJ=25C, VR=100V TJ=85C Forward Current Continuous Peak Symbol VRD VFD IRD Min - Typ - Max 100 1.5 10 50 IFD - - 140 500 mA Symbol VZ VZ CI/O VI/O Min 3750 Typ 4.3 15 3 - Max - Units V V pF Vrms t=10ms A Electrical Characteristics @25C: Zener Diodes Parameter Zener Voltage Between Pins 4&5 and Pins 6&5 Zener Voltage Between Pins 12&11 Input to Output Capacitance Input to Output Isolation Conditions IZT=20mA IZT=20mA - EXAMPLE CIRCUIT VCC 1 680 16 2 4.7F + 15 COUPLING TRANSFORMER TIP 10 MOSFET A DRIVER 3 OFF-HOOK CPU CIRCUIT 14 RING 4 13 5 12 15 B A VCC 10F 15V 6 51k RL 300V SURGE PROTECTION TELEPHONE LINE 25k 4.7F + 11 B 7 8 10 * RING 9 18Vx 2 reverse polarity protection diode; * Denotes half-wave detection only. R04 DIGITAL GROUND 0.47F 250V 8.2k ISOLATED GROUND www.clare.com 3 ITC135P DEVICE PERFORMANCE DATA* 25 20 15 10 5 0 1.17 1.19 1.21 1.23 Power Dissipation (Watts) Device Count (N) 30 Package Power Derating 1.8 LED Forward Voltage Drop (V) 35 Typical LED Forward Voltage Drop vs. Temperature Typical LED Forward Voltage Drop (N=50, IF=5mA, TA=25C) 1.6 1.4 IF=50mA IF=30mA IF=20mA IF=10mA IF=5mA 1.2 1.0 0.8 -40 1.25 -20 0 20 40 60 80 100 1.00 0.95 0.90 0.85 0.80 0.75 0.70 Operating Area 0.65 0.60 0.55 0.50 25 30 35 40 45 50 55 60 65 70 75 80 85 120 Temperature (C) Temperature (C) LED Forward Voltage Drop (V) RELAY PERFORMANCE DATA* 15 10 5 0 1.23 1.58 1.93 2.28 2.63 Typical On-Resistance Distribution (N=50, IL=120mADC, TA=25C) 30 20 15 10 5 2.98 25 20 15 10 5 0 0.06 0.10 0.14 0.18 0.22 0.26 8.75 0.30 9.25 9.75 10.25 10.75 Turn-On Time (ms) Turn-Off Time (ms) On-Resistance (:) Typical IF for Switch Operation (N=50, IL=120mADC, TA=25C) Typical IF for Switch Dropout (N=50, IL=120mADC, TA=25C) Typical Blocking Voltage Distribution (N=50, TA=25C) 15 10 5 0 30 20 15 10 5 0.42 0.54 0.66 0.78 LED Current (mA) 0.90 1.02 25 20 15 10 5 0 0 0.30 35 Device Count (N) 20 25 Device Count (N) Device Count (N) 35 0 0.88 25 Typical Turn-Off Time (N=50, IF=2mA, IL=120mADC, TA=25C) Device Count (N) 20 25 Device Count (N) Device Count (N) 25 Typical Turn-On Time (N=50, IF=2mA, IL=120mADC, TA=25C) 0.18 0.30 0.42 0.54 0.66 LED Current (mA) 0.78 0.90 365 375 385 395 405 415 425 Blocking Voltage (VP) * The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 4 www.clare.com R04 ITC135P Typical Turn-On Time vs. LED Forward Current (IL=120mADC) 2.0 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0 On-Resistance (:) Turn-Off Time (ms) 0.12 0.10 0.08 10 15 20 25 30 35 40 45 5 10 15 20 25 30 35 40 45 -40 50 40 60 Percent of Maximum Load Rating (Typical) (%) 0.30 0.5 0.25 0.20 0.15 0.10 0.05 0 20 40 60 80 -40 100 -20 0 20 40 60 80 100 75 50 25 0 25 50 Temperature (C) Temperature (C) Ambient Temperature (C) Typical IF for Switch Operation vs. Temperature (IL=120mADC) Typical IF for Switch Dropout vs. Temperature (IL=120mADC) Typical Load Current vs. Load Voltage (IF=5mA, TA=25C) 1.8 1.4 1.4 1.2 1.0 0.8 0.6 0.4 1.0 0.8 0.6 0.4 0.2 0 0 0 20 40 60 80 150 1.2 0.2 -20 0 20 40 60 80 Temperature (C) Temperature (C) Typical Blocking Voltage vs. Temperature Typical Leakage vs. Temperature Measured across Pins 15&16 415 410 Leakage (PA) 405 400 395 390 385 380 -20 0 20 40 60 Temperature (C) 80 100 100 50 0 -50 -100 -150 -40 100 85 200 Load Current (mA) 1.6 LED Current (mA) 1.6 100 100 0 -40 0 0 -20 80 Load Current vs. Ambient Temperature (IF=5mA) IF=20mA -40 20 Typical Turn-Off Time vs. Temperature (IF=5mA, IL=120mA) 1.0 -40 0 Typical Turn-On Time vs. Temperature (IL=120mADC) IF=10mA 1.8 -20 Temperature (C) 1.5 -20 20 LED Forward Current (mA) 2.0 -40 30 LED Forward Current (mA) IF=5mA IF=10mA IF=20mA 2.5 0 50 40 0 0.04 5 50 10 100 -200 -2.0 -1.5 -1.0 -0.5 0 0.5 1.0 1.5 2.0 10s 100s Load Voltage (V) Energy Rating Curve 0.10 0.09 0.08 0.07 0.06 0.05 0.04 0.03 0.02 0.01 0 1.2 1.0 Load Current (A) Turn-On Time (ms) 0.14 0.06 3.0 LED Current (mA) 60 0.16 0 Blocking Voltage (VP) Typical On-Resistance vs. Temperature (IF=5mA, IL=120mADC) Typical Turn-Off Time vs. LED Forward Current (IL=120mADC) 0.18 Turn-Off Time (ms) Turn-On Time (ms) RELAY PERFORMANCE DATA (cont)* 0.8 0.6 0.4 0.2 -40 -20 0 20 40 60 Temperature (C) 80 100 0 10Ps 100Ps 1ms 10ms 100ms 1s Time * The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. R04 www.clare.com 5 ITC135P PHOTOTRANSISTOR PERFORMANCE DATA* 24 7 IF=10mA IF=5mA IF=2mA IF=1mA 16 12 8 4 0 4.5 IF=1mA IF=2mA IF=5mA IF=10mA IF=15mA IF=20mA 6 5 4 4.0 Normalized CTR (%) 8 Normalized CTR (%) Collector Current (mA) 28 20 Single Transistor Typical Normalized CTR vs. IF (VCE=0.5V) Single Transistor Typical Normalized CTR vs. Temperature (VCE=0.5V) Typical Transfer Characteristics Single Transistor Detector 3 2 1 0 1 2 3 4 5 6 7 9 8 0 10 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 -40 -20 0 20 Collector Emitter Voltage 40 60 80 100 0 120 2 4 6 8 10 12 14 16 18 20 Forward Current (mA) Temperature (C) Single Transistor - Typical IC vs. IF (VCE=0.5V) Collector Current (mA) 12 10 8 6 4 2 0 0 2 4 6 8 10 12 14 16 18 20 Forward Current (mA) DARLINGTON PERFORMANCE DATA* 3.0 2.5 Normalized CTR (%) 14 12 10 8 6 4 Normalized CTR (%) 16 Collector Current (mA) Darlington Transistor Typical Normalized CTR vs. Temperature (VCE=0.8V) Darlington Transistor Typical Normalized CTR vs. IF (VCE=0.8V) Darlington Transistor - Typical IC vs. IF (VCE=0.5V) 2.0 1.5 1.0 0.5 2 0 2 4 6 8 10 12 14 16 18 0 20 2 4 Forward Current (mA) 6 8 10 12 1.5 1.0 0.5 14 16 18 -40 20 -20 20 40 60 80 100 V-I Characteristics for Test Circuit 120 Ib=10PA 100 Ib=8PA 80 Ib=6PA 60 Ib=4PA 10 9 VIN (Volts) 40 0 Temperature (C) Forward Current (mA) Typical Transfer Characteristics Darlington Transistor Collector Current (mA) 2.0 0 0 0 IF=1mA IF=2mA IF=5mA IF=10mA IF=15mA IF=20mA 2.5 Ib=2PA 20 8 7 6 5 4 0 2 4 6 8 10 20 Collector Emitter Voltage 40 60 80 100 120 IOUT (mA) * The Performance data shown in the graphs above is typical of device performance. For guaranteed parameters not indicated in the written specifications, please contact our application department. 6 www.clare.com R04 ITC135P Manufacturing Information Moisture Sensitivity All plastic encapsulated semiconductor packages are susceptible to moisture ingression. Clare classified all of its plastic encapsulated devices for moisture sensitivity according to the latest version of the joint industry standard, IPC/JEDEC J-STD-020, in force at the time of product evaluation. We test all of our products to the maximum conditions set forth in the standard, and guarantee proper operation of our devices when handled according to the limitations and information in that standard as well as to any limitations set forth in the information or standards referenced below. Failure to adhere to the warnings or limitations as established by the listed specifications could result in reduced product performance, reduction of operable life, and/or reduction of overall reliability. This product carries a Moisture Sensitivity Level (MSL) rating as shown below, and should be handled according to the requirements of the latest version of the joint industry standard IPC/JEDEC J-STD-033. Device Moisture Sensitivity Level (MSL) Rating ITC135P MSL 1 ESD Sensitivity This product is ESD Sensitive, and should be handled according to the industry standard JESD-625. Reflow Profile This product has a maximum body temperature and time rating as shown below. All other guidelines of J-STD-020 must be observed. Device Maximum Temperature x Time ITC135P 260C for 30 seconds Board Wash Clare recommends the use of no-clean flux formulations. However, board washing to remove flux residue is acceptable. Since Clare employs the use of silicone coating as an optical waveguide in many of its optically isolated products, the use of a short drying bake could be necessary if a wash is used after solder reflow processes. Chlorine- or Fluorine-based solvents or fluxes should not be used. Cleaning methods that employ ultrasonic energy should not be used. Pb R04 RoHS 2002/95/EC e3 www.clare.com 7 ITC135P MECHANICAL DIMENSIONS ITC135P 10.1600.381 (0.4000.015) PCB Land Pattern 0.254 0.0127 (0.0100.0005) PIN 16 10.3630.127 (0.4080.005) 7.4930.127 (0.2950.005) 0.635 X 45 (0.025 X 45) 1.016 TYP (0.040 TYP) 9.30 (0.366) 1.90 (0.075) PIN 1 1.270 TYP (0.050 TYP) 1.27 (0.050) 2.108 MAX (0.083 MAX) See Note 3 0.406 TYP (0.016 TYP) 8.890 TYP (0.350 TYP) 0.5080.1016 (0.0200.004) 0.60 (0.024) Lead to Package Standoff: MIN: 0.0254 (0.001) MAX: 0.102 (0.004) DIMENSIONS mm (inches) NOTES: 1. Coplanarity = 0.1016 (0.004) max. 2. Leadframe thickness does not include solder plating (1000 microinch maximum). 3. Sum of package height, standoff, and coplanarity does not exceed 2.108 (0.083). ITC135P Tape & Reel 330.2 DIA. (13.00 DIA.) W=16 (0.630) Top Cover Tape Thickness 0.102 MAX. (0.004 MAX.) B0=10.70 (0.421) K0=3.20 (0.126) A0=10.90 (0.429) P=12.00 (0.472) K1=2.70 (0.106) Embossed Carrier Embossment NOTES: 1. All dimensions carry tolerances of EIA Standard 481-2 2. The tape complies with all "Notes" for constant dimensions listed on page 5 of EIA-481-2 Dimensions mm (inches) For additional information please visit our website at: www.clare.com Clare, Inc. makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any time without notice. Neither circuit patent licenses nor indemnity are expressed or implied. Except as set forth in Clare's Standard Terms and Conditions of Sale, Clare, Inc. assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right. The products described in this document are not designed, intended, authorized or warranted for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or where malfunction of Clare's product may result in direct physical harm, injury, or death to a person or severe property or environmental damage. Clare, Inc. reserves the right to discontinue or make changes to its products at any time without notice. 8 Specification: DS-ITC135P-R04 (c)Copyright 2011, Clare, Inc. All rights reserved. Printed in USA. 10/5/2011