NCP551SN50T1G - ON Semiconductor

February, 2009 − Rev. 16

1Publication Order Number:

NCP551/D

NCP551, NCV551

150 mA CMOS Low Iq

Low-Dropout Voltage

Regulator

The NCP551 series of fixed output low dropout linear regulators are

designed for handheld communication equipment and portable battery

powered applications which require low quiescent. The NCP551

series features an ultra−low quiescent current of 4.0 mA. Each device

contains a voltage reference unit, an error amplifier, a PMOS power

transistor, resistors for setting output voltage, current limit, and

temperature limit protection circuits.

The NCP551 has been designed to be used with low cost ceramic

capacitors and requires a minimum output capacitor of 0.1 mF. The

device is housed in the TSOP−5 surface mount package. Standard

voltage versions are 1.4, 1.5, 1.8, 2.5, 2.7, 2.8, 2.9, 3.0, 3.1, 3.2, 3.3,

and 5.0 V. Other voltages are available in 100 mV steps.

Features

•Low Quiescent Current of 4.0 mA Typical

•Maximum Operating Voltage of 12 V

•Low Output Voltage Option

•High Accuracy Output Voltage of 2.0%

•Industrial Temperature Range of −40°C to 85°C

(NCV551, TA = −40°C to +125°C)

•NCV Prefix for Automotive and Other Applications Requiring Site

and Control Changes

•Pb−Free Packages are Available

Typical Applications

•Battery Powered Instruments

•Hand−Held Instruments

•Camcorders and Cameras

Figure 1. Representative Block Diagram

Driver w/

Current

Limit

Vin Vout

Thermal

Shutdown

Enable

GND

OFF

See detailed ordering and shipping information in the package

dimensions section on page 9 of this data sheet.

ORDERING INFORMATION

TSOP−5

(SOT23−5, SC59−5)

SN SUFFIX

CASE 483

PIN CONNECTIONS AND

MARKING DIAGRAM

3N/C

Vin

2GND

Enable 4

Vout

(Top View)

http://onsemi.com

xxxAYWG

xxx = Specific Device Code

A = Assembly Location

Y = Year

W = Work Week

G= Pb−Free Package

(Note: Microdot may be in either location)

NCP551, NCV551

http://onsemi.com

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

PIN FUNCTION DESCRIPTION

ÁÁÁÁÁ

Pin No.

ÁÁÁÁÁÁ

Pin Name

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Description

ÁÁÁÁÁ

ÁÁÁÁÁÁ

Vin

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Positive power supply input voltage.

ÁÁÁÁÁ

ÁÁÁÁÁÁ

GND

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Power supply ground.

ÁÁÁÁÁ

ÁÁÁÁÁÁ

Enable

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

This input is used to place the device into low−power standby. When this input is pulled low, the

device is disabled. If this function is not used, Enable should be connected to Vin.

ÁÁÁÁÁ

ÁÁÁÁÁÁ

N/C

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

No Internal Connection.

ÁÁÁÁÁ

ÁÁÁÁÁÁ

Vout

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Regulated output voltage.

MAXIMUM RATINGS

Rating Symbol Value Unit

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Input Voltage

ÁÁÁÁÁ

Vin

ÁÁÁÁÁÁÁÁ

0 to 12

ÁÁÁÁ

Enable Voltage VEN −0.3 to Vin +0.3 V

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Output Voltage

ÁÁÁÁÁ

Vout

ÁÁÁÁÁÁÁÁ

−0.3 to Vin +0.3

ÁÁÁÁ

Power Dissipation PDInternally Limited W

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Operating Junction Temperature

ÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ

+150

ÁÁÁÁ

°C

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Operating Ambient Temperature NCP551

NCV551

ÁÁÁÁÁ

ÁÁÁÁÁÁÁÁ

−40 to +85

−40 to +125

ÁÁÁÁ

°C

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Storage Temperature

ÁÁÁÁÁ

Tstg

ÁÁÁÁÁÁÁÁ

−55 to +150

ÁÁÁÁ

°C

Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the

Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect

device reliability.

1. This device series contains ESD protection and exceeds the following tests:

Human Body Model 2000 V per MIL−STD−883, Method 3015

Machine Model Method 200 V

Charge Device Model (CDM) tested C3B per EIA/JESD22−C101.

2. Latchup capability (85°C) "100 mA DC with trigger voltage.

THERMAL CHARACTERISTICS

Rating Symbol Test Conditions Typical Value Unit

ÁÁÁÁÁÁÁÁÁÁ

Junction−to−Ambient

ÁÁÁÁÁÁ

RqJA 1 oz Copper Thickness, 100 mm2

ÁÁÁÁÁÁÁÁ

250

ÁÁÁÁ

°C/W

PSIJ−Lead 2 YJ−L2 1 oz Copper Thickness, 100 mm268 °C/W

NOTE: Single component mounted on an 80 x 80 x 1.5 mm FR4 PCB with stated copper head spreading area. Using the following

boundary conditions as stated in EIA/JESD 51−1, 2, 3, 7, 12.

NCP551, NCV551

http://onsemi.com

ELECTRICAL CHARACTERISTICS

(Vin = Vout(nom.) + 1.0 V, VEN = Vin, Cin = 1.0 mF, Cout = 1.0 mF, TA = 25°C, unless otherwise noted.)

Characteristic Symbol Min Typ Max Unit

Output Voltage (TA = 25°C, Iout = 10 mA)

1.4 V

1.5 V

1.8 V

2.5 V

2.7 V

2.8 V

2.9 V

3.0 V

3.1 V

3.2 V

3.3 V

5.0 V

Vout

1.358

1.455

1.746

2.425

2.646

2.744

2.842

2.940

3.038

3.136

3.234

4.90

1.4

1.5

1.8

2.5

2.7

2.8

2.9

3.0

3.1

3.2

3.3

5.0

1.442

1.545

1.854

2.575

2.754

2.856

2.958

3.060

3.162

3.264

3.366

5.10

Output Voltage (TA = Tlow to Thigh, Iout = 10 mA)

1.4 V

1.5 V

1.8 V

2.5 V

2.7 V

2.8 V

2.9 V

3.0 V

3.1 V

3.2 V

3.3 V

5.0 V

Vout

1.344

1.440

1.728

2.400

2.619

2.716

2.813

2.910

3.007

3.104

3.201

4.850

1.4

1.5

1.8

2.5

2.7

2.8

2.9

3.0

3.1

3.2

3.3

5.0

1.456

1.560

1.872

2.600

2.781

2.884

2.987

3.090

3.193

3.296

3.399

5.150

Line Regulation (Vin = Vout + 1.0 V to 12 V, Iout = 10 mA) Regline −10 30 mV

Load Regulation (Iout = 10 mA to 150 mA, Vin = Vout + 2.0 V) Regload −40 65 mV

Output Current (Vout = (Vout at Iout = 100 mA) −3%)

1.4 V−2.0 V (Vin = 4.0 V)

2.1 V−3.0 V (Vin = 5.0 V)

3.1 V−4.0 V (Vin = 6.0 V)

4.1 V−5.0 V (Vin = 8.0 V)

Io(nom.)

150

−

Dropout Voltage (Iout = 10 mA, Measured at Vout −3.0%)

1.4 V

1.5 V, 1.8 V, 2.5 V

2.7 V, 2.8 V, 2.9 V, 3.0 V, 3.1 V, 3.2 V, 3.3 V, 5.0 V

Vin−Vout

−

170

130

250

220

150

Quiescent Current

(Enable Input = 0 V)

(Enable Input = Vin, Iout = 1.0 mA to Io(nom.))

−

0.1

4.0

1.0

8.0

Output Voltage Temperature Coefficient Tc−"100 −ppm/°C

Enable Input Threshold Voltage

(Voltage Increasing, Output Turns On, Logic High)

(Voltage Decreasing, Output Turns Off, Logic Low)

Vth(en)

1.3

−

0.3

Output Short Circuit Current (Vout = 0 V)

1.4 V−2.0 V (Vin = 4.0 V)

2.1 V−3.0 V (Vin = 5.0 V)

3.1 V−4.0 V (Vin = 6.0 V)

4.1 V−5.0 V (Vin = 8.0 V)

Iout(max)

160

350

600

3. Maximum package power dissipation limits must be observed.

PD +TJ(max) *TA

RqJA

4. Low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.

5. NCP551 Tlow = −40°CT

high = +85°C

NCV551 Tlow = −40°CT

high = +125°C.

NCP551, NCV551

http://onsemi.com

DEFINITIONS

Load Regulation

The change in output voltage for a change in output

current at a constant temperature.

Dropout Voltage

The input/output differential at which the regulator output

no longer maintains regulation against further reductions in

input voltage. Measured when the output drops 3% below its

nominal. The junction temperature, load current, and

minimum input supply requirements affect the dropout level.

Maximum Power Dissipation

The maximum total dissipation for which the regulator

will operate within its specifications.

Quiescent Current

The quiescent current is the current which flows through

the ground when the LDO operates without a load on its

output: internal IC operation, bias, etc. When the LDO

becomes loaded, this term is called the Ground current. It is

actually the difference between the input current (measured

through the LDO input pin) and the output current.

Line Regulation

The change in output voltage for a change in input voltage.

The measurement is made under conditions of low

dissipation or by using pulse technique such that the average

chip temperature is not significantly affected.

Line Transient Response

Typical over and undershoot response when input voltage

is excited with a given slope.

Thermal Protection

Internal thermal shutdown circuitry is provided to protect

the integrated circuit in the event that the maximum junction

temperature is exceeded. When activated at typically 160°C,

the regulator turns off. This feature is provided to prevent

failures from accidental overheating.

Maximum Package Power Dissipation

The maximum power package dissipation is the power

dissipation level at which the junction temperature reaches

its maximum operating value, i.e. 125°C. Depending on the

ambient power dissipation and thus the maximum available

output current.

NCP551, NCV551

http://onsemi.com

3.25

755025

GROUND CURRENT (mA)

3.05

Figure 2. Ground Pin Current versus

Output Current

3.35

Iout, OUTPUT CURRENT (mA)

3.3

100 150125

3.1

3.2

3.15

Vout = 2.8 V

Figure 3. Ground Pin Current versus

Output Current

3.35

755025

GROUND CURRENT (mA)

3.15

3.45

Iout, OUTPUT CURRENT (mA)

3.4

100 150125

3.2

3.3

3.25

Vout = 3.3 V

0.5

Figure 4. Ground Pin Current versus

Input Voltage

Vin, INPUT VOLTAGE (VOLTS)

Figure 5. Ground Pin Current versus

Input Voltage

GROUND PIN CURRENT (mA)

086421012

1.5

2.5

3.5

Vout(nom) = 2.8 V

Iout = 25 mA

0.5

Vin, INPUT VOLTAGE (VOLTS)

GROUND PIN CURRENT (mA)

086421012

1.5

2.5

3.5

Vout(nom) = 3.3 V

Iout = 25 mA

400

−200

200

−600

600

200

400200

TIME (ms)

Figure 6. Line Transient Response Figure 7. Line Transient Response

Vin = 3.8 V to 4.8 V

Vout = 2.8 V

Cout = 1 mF

Iout = 10 mA

TIME (ms)

−200

400

800 1600

−400

12001000 1400

OUTPUT VOLTAGE

DEVIATION (mV)

Vin, INPUT

VOLTAGE (V)

OUTPUT VOLTAGE

DEVIATION (mV)

Vin, INPUT

VOLTAGE (V)

600400200 800 16

12001000 1400

Vin = 3.8 V to 4.8 V

Vout = 2.8 V

Cout = 1 mF

Iout = 100 mA

NCP551, NCV551

http://onsemi.com

400

−200

200

−600

600

200

400200

TIME (ms)

Figure 8. Line Transient Response Figure 9. Line Transient Response

TIME (ms)

−200

400

800 1600

−400

12001000 1400

OUTPUT VOLTAGE

DEVIATION (mV)

Vin, INPUT

VOLTAGE (V)

OUTPUT VOLTAGE

DEVIATION (mV)

Vin, INPUT

VOLTAGE (V)

600400200 800 160

12001000 1400

Vin = 4.3 V to 5.3 V

Vout = 3.3 V

Cout = 1 mF

Iout = 10 mA

Vin = 3.8 V to 4.8 V

Vout = 2.8 V

Cout = 1 mF

Iout = 150 mA

−600

400

−200

200

−600

500

200

300100

Figure 10. Line Transient Response Figure 11. Line Transient Response

TIME (ms)

−200

400

700 1900

−400

1100900 1700

OUTPUT VOLTAGE

DEVIATION (mV)

Vin, INPUT

VOLTAGE (V)

OUTPUT VOLTAGE

DEVIATION (mV)

Vin, INPUT

VOLTAGE (V)

400 800 200

1200

Vin = 4.3 V to 5.3 V

Vout = 3.3 V

Cout = 1 mF

Iout = 150 mA

Vin = 4.3 V to 5.3 V

Vout = 3.3 V

Cout = 1 mF

Iout = 100 mA

−600

600

800

15001300

TIME (ms)

600

1600

150

321

OUTPUT VOLTAGE

DEVIATION (mV)

−1000

TIME (ms)

Figure 12. Load Transient Response ON Figure 13. Load Transient Response OFF

Iout = 3.0 mA − 150 mA

TIME (ms)

−500

456789

Iout, OUTPUT

CURRENT (mA)

150

1000

−500

500

OUTPUT VOLTAGE

DEVIATION (mV)

Iout, OUTPUT

CURRENT (mA)

0321 456789

Vout = 2.8 V

Cout = 10 mF

Vout = 2.8 V

Cout = 10 mF

Iout = 3.0 mA − 150 mA

NCP551, NCV551

http://onsemi.com

Figure 14. Load Transient Response OFF

TIME (ms)

Figure 15. Load Transient Response ON

TIME (ms)

150

−500

500

150

−500

−1000

1000

0321456789 0321 456789

OUTPUT VOLTAGE

DEVIATION (mV)

Iout, OUTPUT

CURRENT (mA)

OUTPUT VOLTAGE

DEVIATION (mV)

Iout, OUTPUT

CURRENT (mA)

Vout = 3.3 V

Cout = 10 mF

Vout = 3.3 V

Cout = 10 mF

Iout = 3.0 mA − 150 mA Iout = 3.0 mA − 150 mA

600

400200

Figure 16. Turn−On Response

Vin = 4.3 V

Vout = 3.3 V

RO = 3.3 k

VEN = 2.0 V

TIME (ms)

800 200012001000 1400

Vout, OUTPUT

VOLTAGE (V)

ENABLE

VOLTAGE (V)

1600 1800 0

600

400200

Figure 17. Turn−On Response

Vin = 3.8 V

Vout = 2.8 V

RO = 2.8 k

VEN = 2.0 V

TIME (ms)

800 200

12001000 1400

Vout, OUTPUT

VOLTAGE (V)

ENABLE

VOLTAGE (V)

1600 1800

Co = 1 mF

Co = 10 mF

Co = 1 mF

Co = 10 mF

Figure 18. Output Voltage versus Input Voltage Figure 19. Output Voltage versus Input Voltage

642

Vout, OUTPUT VOLTAGE (VOLTS)

Vin, INPUT VOLTAGE (VOLTS)

2.5

81210

0.5

1.5

Vin = 0 V to 12 V

Vout(nom) = 2.8 V

Iout = 10 mA

Cin = 1 mF

Cout = 1 mF

VEN = Vin

642

Vout, OUTPUT VOLTAGE (VOLTS)

Vin, INPUT VOLTAGE (VOLTS)

2.5

81210

0.5

1.5

Vin = 0 V to 12 V

Vout = 3.3 V

Iout = 10 mA

Cin = 1 mF

Cout = 1 mF

VEN = Vin

3.5

NCP551, NCV551

http://onsemi.com

APPLICATIONS INFORMATION

A typical application circuit for the NCP551 series is

shown in Figure 20.

Input Decoupling (C1)

A 0.1 mF capacitor either ceramic or tantalum is

recommended and should be connected close to the NCP551

package. Higher values and lower ESR will improve the

overall line transient response.

Output Decoupling (C2)

The NCP551 is a stable Regulator and does not require

any specific Equivalent Series Resistance (ESR) or a

minimum output current. Capacitors exhibiting ESRs

ranging from a few mW up to 3.0 W can thus safely be used.

The minimum decoupling value is 0.1 mF and can be

augmented to fulfill stringent load transient requirements.

The regulator accepts ceramic chip capacitors as well as

tantalum devices. Larger values improve noise rejection and

load regulation transient response.

Enable Operation

The enable pin will turn on or off the regulator. These

limits of threshold are covered in the electrical specification

section of this data sheet. If the enable is not used then the

pin should be connected to Vin.

Hints

Please be sure the Vin and GND lines are sufficiently wide.

When the impedance of these lines is high, there is a chance

to pick up noise or cause the regulator to malfunction.

Set external components, especially the output capacitor,

as close as possible to the circuit, and make leads as short as

possible.

Thermal

As power across the NCP551 increases, it might become

necessary to provide some thermal relief. The maximum

power dissipation supported by the device is dependent

upon board design and layout. Mounting pad configuration

on the PCB, the board material, and also the ambient

temperature effect the rate of temperature rise for the part.

This is stating that when the NCP551 has good thermal

conductivity through the PCB, the junction temperature will

be relatively low with high power dissipation applications.

The maximum dissipation the package can handle is

given by:

PD +TJ(max) *TA

RqJA

If junction temperature is not allowed above the

maximum 125°C, then the NCP551 can dissipate up to

400 mW @ 25°C.

The power dissipated by the NCP551 can be calculated

from the following equation:

Ptot +ƪVin *I

gnd (Iout)ƫ)[Vin *Vout]*I

out

VinMAX +Ptot )Vout *Iout

IGND )Iout

If a 150 mA output current is needed then the ground

current from the data sheet is 4.0 mA. For an

NCP551SN30T1 (3.0 V), the maximum input voltage will

then be 5.6 V.

Battery or

Unregulated

Voltage

Figure 20. Typical Application Circuit

Vout

OFF

NCP551, NCV551

http://onsemi.com

Output

Input

1.0 mF 1.0 mF

Output

Input

1.0 mF 1.0 mF

Output

Input

1.0 mF1.0 mF

Output

Enable

1.0 mF 1.0 mF

Output

Input

1.0 mF1.0 m

11 V

Figure 21. Current Boost Regulator Figure 22. Current Boost Regulator with

Short Circuit Limit

Figure 23. Delayed Turn−on

Figure 24. Input Voltages Greater than 12 V

The NCP551 series can be current boosted with a PNP transist-

or. Resistor R in conjunction with VBE of the PNP determines

when the pass transistor begins conducting; this circuit is not

short circuit proof. Input/Output differential voltage minimum is

increased by VBE of the pass resistor.

Short circuit current limit is essentially set by the VBE of Q2 and

R1. ISC = ((VBEQ2 − ib * R2) / R1) + IO(max) Regulator

If a delayed turn−on is needed during power up of several

voltages then the above schematic can be used. Resistor R,

and capacitor C, will delay the turn−on of the bottom regulator.

A regulated output can be achieved with input voltages that

exceed the 12 V maximum rating of the NCP551 series with

the addition of a simple pre−regulator circuit. Care must be

taken to prevent Q1 from overheating when the regulated

output (Vout) is shorted to GND.

ORDERING INFORMATION

Device

Nominal

Output Voltage Marking Package Shipping†

NCP551SN15T1 1.5 LAO TSOP−53000 / Tape & Reel

NCP551SN15T1G 1.5 LAO TSOP−5

(Pb−Free) 3000 / Tape & Reel

NCP551SN18T1 1.8 LAP TSOP−53000 / Tape & Reel

NCP551SN18T1G 1.8 LAP TSOP−5

(Pb−Free) 3000 / Tape & Reel

NCP551SN25T1 2.5 LAQ TSOP−53000 / Tape & Reel

NCP551SN25T1G 2.5 LAQ TSOP−5

(Pb−Free) 3000 / Tape & Reel

NCP551SN27T1 2.7 LAR TSOP−53000 / Tape & Reel

NCP551SN27T1G 2.7 LAR TSOP−5

(Pb−Free) 3000 / Tape & Reel

NOTE: Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specific-

ations Brochure, BRD8011/D.

6. NCV551 is qualified for automotive use.

NCP551, NCV551

http://onsemi.com

ORDERING INFORMATION

Device Shipping†

PackageMarking

Nominal

Output Voltage

NCP551SN28T1 2.8 LAS TSOP−53000 / Tape & Reel

NCP551SN28T1G 2.8 LAS TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCP551SN29T1G 2.9 LJL TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCP551SN30T1 3.0 LAT TSOP−53000 / Tape & Reel

NCP551SN30T1G 3.0 LAT TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCP551SN31T1G 3.1 LJM TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCP551SN32T1G 3.2 LIV TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCP551SN33T1 3.3 LAU TSOP−53000 / Tape & Reel

NCP551SN33T1G 3.3 LAU TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCP551SN50T1 5.0 LAV TSOP−53000 / Tape & Reel

NCP551SN50T1G 5.0 LAV TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN14T1G 1.4 AAT TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN15T1 1.5 LFZ TSOP−53000 / Tape & Reel

NCV551SN15T1G 1.5 LFZ TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN18T1 1.8 LGA TSOP−53000 / Tape & Reel

NCV551SN18T1G 1.8 LGA TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN25T1 2.5 LGB TSOP−53000 / Tape & Reel

NCV551SN25T1G 2.5 LGB TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN27T1 2.7 LGC TSOP−53000 / Tape & Reel

NCV551SN27T1G 2.7 LGC TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN28T1 2.8 LGD TSOP−53000 / Tape & Reel

NCV551SN28T1G 2.8 LGD TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN30T1 3.0 LGE TSOP−53000 / Tape & Reel

NCV551SN30T1G 3.0 LGE TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN31T1G 3.1 LJR TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN32T1 3.2 LFR TSOP−53000 / Tape & Reel

NCV551SN32T1G 3.2 LFR TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN33T1 3.3 LGG TSOP−53000 / Tape & Reel

NCV551SN33T1G 3.3 LGG TSOP−5

(Pb−Free)

3000 / Tape & Reel

NCV551SN50T1 5.0 LGF TSOP−53000 / Tape & Reel

NCV551SN50T1G 5.0 LGF TSOP−5

(Pb−Free)

3000 / Tape & Reel

NOTE: Additional voltages in 100 mV steps are available upon request by contacting your ON Semiconductor representative.

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specific-

ations Brochure, BRD8011/D.

6. NCV551 is qualified for automotive use.

NCP551, NCV551

http://onsemi.com

PACKAGE DIMENSIONS

TSOP−5

CASE 483−02

ISSUE F

NOTES:

1. DIMENSIONING AND TOLERANCING PER

ASME Y14.5M, 1994.

2. CONTROLLING DIMENSION: MILLIMETERS.

3. MAXIMUM LEAD THICKNESS INCLUDES

LEAD FINISH THICKNESS. MINIMUM LEAD

THICKNESS IS THE MINIMUM THICKNESS

OF BASE MATERIAL.

4. DIMENSIONS A AND B DO NOT INCLUDE

MOLD FLASH, PROTRUSIONS, OR GATE

BURRS.

5. OPTIONAL CONSTRUCTION: AN

ADDITIONAL TRIMMED LEAD IS ALLOWED

IN THIS LOCATION. TRIMMED LEAD NOT TO

EXTEND MORE THAN 0.2 FROM BODY.

DIM MIN MAX

MILLIMETERS

A3.00 BSC

B1.50 BSC

C0.90 1.10

D0.25 0.50

G0.95 BSC

H0.01 0.10

J0.10 0.26

K0.20 0.60

L1.25 1.55

M0 10

S2.50 3.00

123

54 S

0.7

0.028

1.0

0.039

ǒmm

inchesǓ

SCALE 10:1

0.95

0.037

2.4

0.094

1.9

0.074

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and

Mounting Techniques Reference Manual, SOLDERRM/D.

SOLDERING FOOTPRINT*

0.20

CAB

T0.10

2X T0.20

NOTE 5

SEATING

PLANE

0.05

DETAIL Z

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice

to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability

arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.

“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All

operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights

nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications

intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should

Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,

and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal

Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

N. American Technical Support: 800−282−9855 Toll Free

USA/Canada

Europe, Middle East and Africa Technical Support:

Phone: 421 33 790 2910

Japan Customer Focus Center

Phone: 81−3−5773−3850

NCP551/D

LITERATURE FULFILLMENT:

Literature Distribution Center for ON Semiconductor

P.O. Box 5163, Denver, Colorado 80217 USA

Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada

Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada

Email: orderlit@onsemi.com

ON Semiconductor Website: www.onsemi.com

Order Literature: http://www.onsemi.com/orderlit

For additional information, please contact your local

Sales Representative