VN751S High side driver Features Type RDS(on) Iout VCC VN751S 60 m 2.5 A 36 V SO-8 CMOS compatible input Thermal shutdown Description Shorted load protection Undervoltage and overvoltage shutdown Protection against loss of ground Very low standby current Compliance to 61000-4-4 IEC test up to 4 kV Open drain status output The VN751S is a monolithic device designed in STMicroelectronics VIPower M0-3 technology, intended for driving any kind of load with one side connected to ground. Active VCC pin voltage clamp protects the device against low energy spikes. Active current limitation combined with thermal shutdown and automatic restart protect the device against overload. Device automatically turns off in case of ground pin disconnection. This device is especially suitable for industrial applications in conformity with IEC 61131-2 programmable controllers international standard. Figure 1. Block diagram VCC OVERVOLTAGE DETECTION VCC CLAMP UNDERVOLTAGE DETECTION GND Power CLAMP DRIVER OUTPUT LOGIC INPUT CURRENT LIMITER STATUS OVERTEMPERATURE DETECTION November 2009 Doc ID 12320 Rev 7 1/17 www.st.com 17 Contents VN751S Contents 1 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Waveforms and truth table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 5 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 6 Application schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 7 Reverse polarity protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 8 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 9 Order code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 Doc ID 12320 Rev 7 VN751S 1 Maximum ratings Maximum ratings Table 1. Absolute maximum rating Symbol Value Unit DC supply voltage (overvoltage protected) 45 V - VCC Reverse DC supply voltage -0.3 V - IGND DC reverse ground pin current -200 mA Internally limited A -5 A VCC IOUT - IOUT Parameter DC output current Reverse DC output current IIN DC input current +/- 10 mA ISTAT DC status current +/- 10 mA VESD Electrostatic discharge (R = 1.5 k; C = 100 pF) 5000 V Ptot Power dissipation TC = 25 C Internally limited W TJ Junction operating temperature Internally limited C Tc Case operating temperature - 40 to 150 C Tstg Storage temperature - 55 to 150 C EAS Single-pulse avalanche energy 0.8 J Value Unit 93(1) C/W 82(2) C/W 15 C/W Table 2. Symbol RthJA RthJC Thermal data Parameter Thermal resistance junction-ambient Thermal resistance junction-case Max Max 1. When mounted on a standard single-sided FR-4 board with 0.5 cm2 of Cu (at least 35m) thick connected to all VCC pins. Horizontal mounting and no artificial air flow. 2. When mounted on a standard single-sided FR-4 board with 2 cm2 of Cu (at least 35m) thick connected to all VCC pins. Horizontal mounting and no artificial air flow. Doc ID 12320 Rev 7 3/17 Pin connections 2 4/17 VN751S Pin connections Figure 2. Connection diagram (top view) Figure 3. Current and voltage conventions Doc ID 12320 Rev 7 VN751S 3 Electrical characteristics Electrical characteristics 8 V < VCC < 36 V; -40 C < TJ < 125 C, unless otherwise specified Table 3. Symbol Power Parameter Test conditions Min Typ Max Unit VCC Operating supply voltage VUSD Undervoltage shut-down 3 VOV Overvoltage shut-down 36 RON On state resistance 5.5 IOUT = 2 A; TJ = 25 C Table 4. Symbol V 180 10 1.5 On state; VCC = 24 V;TCASE =100 C IL(off) 5.5 60 On state; VCC = 24 V Supply current V V IOUT = 2 A Off state; VCC = 24 V; TCASE =25 C IS 4 36 Off state output current VIN = VOUT = 0 V 0 m m 1.8 A mA mA 10 A 20 Switching (VCC = 24 V) Parameter Test conditions Min Typ Max Unit td(on) Turn-on delay time RL = 12 from VIN rising edge to VOUT = 2.4 V 12 s td(off) Turn-off delay time RL = 12 from VIN falling edge to VOUT = 21.6 V 35 s dVOUT/dt(on) Turn -on voltage slope RL = 12 from VOUT = 2.4 V to VOUT = 19.2 V 0.80 V/s dVOUT/dt(off) Turn -off voltage slope RL = 12 from VOUT = 21.6 V to VOUT = 2.4 V 0.30 V/s Doc ID 12320 Rev 7 5/17 Electrical characteristics Table 5. Symbol Input pin Parameter VIL Input low level IIL Low level input current VIH Input high level IIH High level input current Vhyst Input hysteresis voltage IIN VICL Table 6. Symbol Test conditions Min Typ Max Unit 1.25 VIN = 1.25 V 1 A 3.25 V VIN = 3.25 V 10 0.5 Input clamp voltage IIN = 1 mA A V VIN = VCC = 5 V Input current V 10 A 6 6.8 -0.7 8 V V Min Typ Max Unit IIN = -1 mA Status pin Parameter Test conditions VSTAT Status low output voltage ISTAT = 1.6 mA 0.5 V ILSTAT Status leakage current Normal operation; VSTAT = 5 V 10 A CSTAT Status pin input capacitance Normal operation; VSTAT = 5 V 100 pF VSCL Status clamp voltage ISTAT = 1 mA; ISTAT =-1 mA 8 V V 6 6.8 -0.7 Min Typ Max Unit Shut-down temperature 150 175 200 TR Reset temperature 135 Thyst Thermal hysteresis 7 Table 7. Symbol TTSD Ilim Vdemag 6/17 VN751S Protections Parameter Test conditions Current limitation VCC = 24 V, RLOAD = 10 m, t = 0.4 ms Turn-off output clamp voltage RL =12 ; L = 6 mH Doc ID 12320 Rev 7 C 20 2.7 VCC47 C VCC52 C 6.0 A VCC57 V VN751S 4 Waveforms and truth table Waveforms and truth table Figure 4. Switching time waveforms VOUT 90% 80% dVOUT/dt(off) dVOUT/dt(on) 10% t VIN td(on) td(off) t Table 8. Truth table Conditions Input Output Status Normal operation L H L H H H Current limitation L H H L X X Overtemperature L H L L H L Undervoltage L H L L X X Overvoltage L H L L H H Doc ID 12320 Rev 7 H (TJ < TTSD) H (TJ > TTSD) L 7/17 Waveforms and truth table Figure 5. VN751S Waveforms NORMAL OPERATION INPUT LOAD VOLTAGE STATUS UNDERVOLTAGE VUSDhyst VCC VUSD INPUT LOAD VOLTAGE undefined STATUS OVERVOLTAGE VCCVOV VCC INPUT LOAD VOLTAGE STATUS TJ TTSD TR OVERTEMPERATURE INPUT LOAD CURRENT STATUS 8/17 Doc ID 12320 Rev 7 VN751S 5 Test circuit Test circuit Figure 6. Peak short circuit current test circuit R Figure 7. Avalanche energy test circuit R Doc ID 12320 Rev 7 9/17 Application schematic 6 Application schematic Figure 8. 10/17 VN751S Application schematic Doc ID 12320 Rev 7 VN751S 7 Reverse polarity protection Reverse polarity protection A schematic solution to protect the IC against a reverse polarity condition is proposed. This schematic is effective with any type of load connected to the outputs of the IC. The RGND resistor value can be selected according to the following conditions to be met: RGND 600 mV / (IS in ON state max). RGND (-VCC) / (-IGND) where -IGND is the DC reverse ground pin current and can be found in the absolute maximum rating section of the device datasheet. The power dissipation associated to RGND during reverse polarity condition is: PD = (-VCC)2/RGND This resistor can be shared by several different ICs. In such case IS value on formula (1) is the sum of the maximum ON-state currents of the different devices. Please note that if the microprocessor ground and the device ground are separated then the voltage drop across the RGND (given by IS in ON state max * RGND) produce a difference between the generated input level and the IC input signal level. This voltage drop will vary depending on how many devices are ON in the case of several high side switches sharing the same RGND. Figure 9. Reverse polarity protection + Vcc Statusi Outputi Inputi RGND GND Load (Optional) Doc ID 12320 Rev 7 11/17 Package mechanical data 8 VN751S Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 12/17 Doc ID 12320 Rev 7 VN751S Package mechanical data Table 9. SO-8 mechanical data mm inch Dim. Min Typ A a1 Max Min Typ 1.75 0.1 0.068 0.25 a2 Max 0.003 0.009 1.65 0.064 a3 0.65 0.85 0.025 0.033 b 0.35 0.48 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.019 c1 45 (typ.) D 4.8 5.0 0.188 0.196 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F 3.8 4.0 0.14 0.157 L 0.4 1.27 0.015 0.050 M 0.6 S 0.023 8 (max.) Figure 10. Package dimensions Doc ID 12320 Rev 7 13/17 Package mechanical data VN751S Figure 11. SO-8 tape and reel information 14/17 Doc ID 12320 Rev 7 VN751S 9 Order code Order code Table 10. Order codes Order codes Package Packaging VN751S SO-8 Tube VN751STR SO-8 tape and reel Doc ID 12320 Rev 7 15/17 Revision history 10 VN751S Revision history Table 11. 16/17 Document revision history Date Revision Changes 18-Sep-2006 1 Initial release 12-Mar-2007 2 Document reformatted, typo in Section Table 3.: Power on page 5, updated Ptot value Table 2. 15-May-2007 3 Typo in Table 1 on page 3 VESD 18-Sep-2007 4 Added ISTAT value in Table 1 on page 3 11-Oct-2007 5 Updated Table 2 on page 3 08-Jul-2008 6 Added Section 7 on page 10 30-Nov-2009 7 Updated coverpage and Chapter 6 on page 10 Doc ID 12320 Rev 7 VN751S Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 12320 Rev 7 17/17