DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M www.ti.com SNLS352C - MAY 1999 - REVISED FEBRUARY 2013 DS26LS32AC/DS26LS32C/DS26LS32M/DS26LS33M Quad Differential Line Receivers Check for Samples: DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M FEATURES DESCRIPTION * The DS26LS32 and DS26LS32A are quad differential line receivers designed to meet the RS-422, RS-423 and Federal Standards 1020 and 1030 for balanced and unbalanced digital data transmission. 1 2 * * * * * * High Differential or Common-Mode Input Voltage Ranges of 7V on the DS26LS32 and DS26LS32A and 15V on the DS26LS33 0.2V Sensitivity Over the Input Voltage Range on the DS26LS32 and DS26LS32A, 0.5V Sensitivity on the DS26LS33 DS26LS32 and DS26LS32A Meet All Requirements of RS-422 and RS-423 6k Minimum Input Impedance 100 mV Input Hysteresis on the DS26LS32 and DS26LS32A, 200 mV on the DS26LS33 Operation From a Single 5V Supply TRI-STATE Outputs, with Choice of Complementary Output Enables for Receiving Directly onto a Data Bus The DS26LS32 and DS26LS32A have an input sensitivity of 200 mV over the input voltage range of 7V and the DS26LS33 has an input sensitivity of 500 mV over the input voltage range of 15V. The DS26LS32A differs in function from the popular DS26LS32 and DS26LS33 in that input pull-up and pull-down resistors are included which prevent output oscillation on unused channels. Each version provides an enable and disable function common to all four receivers and features TRI-STATE outputs with 8 mA sink capability. Constructed using low power Schottky processing, these devices are available over the full military and commercial operating temperature ranges. Logic Diagram 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M SNLS352C - MAY 1999 - REVISED FEBRUARY 2013 www.ti.com Connection Diagram For Complete Military Product Specifications, refer to the appropriate SMD or MDS. Figure 1. Dual-In-Line Package (Top View) D Package or NFG0016E Package Figure 2. 20-Lead Ceramic Leadless Chip Carrier Truth Table ENABLE ENABLE Input Output 0 1 X Hi-Z See note below. (2) (1) (2) 2 (1) VID VTH (Max) 1 VID VTH (Min) 0 Hi-Z = TRI-STATE Note: Input conditions may be any combination not defined for ENABLE and ENABLE . Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M www.ti.com SNLS352C - MAY 1999 - REVISED FEBRUARY 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) Supply Voltage 7V Common-Mode Range 25V Differential Input Voltage 25V Enable Voltage 7V Output Sink Current Maximum Power Dissipation 50 mA (3) at 25C Cavity Package 1433 mW Molded DIP Package 1362 mW SOIC Package (4) DS26LS32 1002 mW DS26LS32A 1051 mW -65C to +165C Storage Temperature Range Lead Temperature (Soldering, 4 seconds) (1) 260C "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device should be operated at these limits. The table of "Electrical Characteristics" provides conditions for actual device operation. If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications. Derate cavity package 9.6 mW/C above 25C; derate molded DIP package 10.9 mW/C above 25C. Derate SOIC Package 8.01 mW/C for DS26LS32 8.41 mW/C for DS26LS32A (2) (3) (4) Operating Conditions Min Max Units Supply Voltage, (VCC) DS26LS32M, DS26LS33M (MIL) 4.5 5.5 V DS26LS32C, DS26LS32AC (COML) 4.75 5.25 V -55 +125 C 0 +70 C Temperature, (TA) DS26LS32M, DS26LS33M (MIL) DS26LS32C, DS26LS32AC (COML) Electrical Characteristics (1) (2) (3) over the operating temperature range unless otherwise specified Symbol Parameter Min Typ Max Units DS26LS32, DS26LS32A, -7V VCM +7V Conditions -0.2 0.07 0.2 V DS26LS33, DS26LS33A, -15V VCM +15V -0.5 0.14 0.5 6.0 8.5 VTH Differential Input Voltage VOUT = VOH or VOL RIN Input Resistance -15V VCM +15V (One Input AC GND) IIN Input Current (Under Test) V IN = 15V, Other Input -15V VIN +15V 2.3 mA V IN = -15V, Other Input -15V VIN +15V -2.8 mA Output High Voltage VCC = MIN, VIN = 1V, Commercial 2.7 4.2 VENABLE = 0.8V, IOH = -440 A Military 2.5 4.2 VCC = Min, VIN = -1V, IOL = 4 mA 0.4 V VENABLE = 0.8V IOL = 8 mA 0.45 V 0.8 V VOH VOL Output Low Voltage VIL Enable Low Voltage VIH Enable High Voltage VI Enable Clamp Voltage (1) (2) (3) V V 2.0 VCC = Min, IIN = -18 mA V k V -1.5 V All currents into device pins are shown as positive, all currents out of device pins are shown as negative, all voltages are referenced to ground, unless otherwise specified. All values shown as max or min are so classified on absolute value basis. All typical values are VCC = 5V, TA = 25C. Only one output at a time should be shorted. Copyright (c) 1999-2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M 3 DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M SNLS352C - MAY 1999 - REVISED FEBRUARY 2013 Electrical Characteristics (1) (2) (3) www.ti.com (continued) over the operating temperature range unless otherwise specified Symbol IO Parameter Conditions Min Typ Max Units VO = 2.4V 20 A VO = 0.4V -20 A OFF-State (High Impedance) Output Current V CC = Max IIL Enable Low Current VIN = 0.4V -0.36 mA IIH Enable High Current VIN = 2.7V 20 A ISC Output Short-Circuit Current V O = 0V, VCC = Max, VIN = 1V -85 mA ICC Power Supply Current VCC = Max, All VIN = GND, DS26LS32, DS26LS32A 52 70 mA Outputs Disabled DS26LS33, DS26LS33A 57 80 mA II Input High Current VIN = 5.5V VHYST Input Hysteresis TA = 25C, VCC = 5V, DS26LS32, DS26S32A 100 mV VCM = 0V DS26LS33, DS26LS33A 200 mV -15 100 A Switching Characteristics VCC = 5V, TA = 25C Symbol tPLH Parameter Conditions Input to Output CL = 15 pF tPHL tLZ ENABLE to Output CL = 5 pF ENABLE to Output CL = 15 pF tHZ tZL tZH DS26LS32/DS26LS33 Min DS26LS32A/DS26LS33A Typ Max 17 17 Min Units Typ Max 25 23 35 ns 25 23 35 ns 20 30 15 30 ns 15 22 20 25 ns 15 22 14 22 ns 15 22 15 22 ns AC TEST CIRCUIT AND SWITCHING TIME WAVEFORMS Figure 3. Load Test Circuit for TRI-STATE Outputs 4 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M www.ti.com SNLS352C - MAY 1999 - REVISED FEBRUARY 2013 Diagram shown for ENABLE low. Pulse generator for all pulses: Rate = 1.0 MHz; ZO = 50; tr 6 ns; tf 6.0 ns. Figure 4. Propagation Delay S1 and S2 of load circuit are closed except where shown. Pulse generator for all pulses: Rate = 1.0 MHz; ZO = 50; tr 6 ns; tf 6.0 ns. Figure 5. Enable and Disable Times TYPICAL APPLICATIONS Figure 6. Two-Wire Balanced Interface--RS-422 Figure 7. Single Wire with Driver Ground Reference--RS-423 Copyright (c) 1999-2013, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M 5 DS26LS32AC, DS26LS32C, DS26LS32M, DS26LS33M SNLS352C - MAY 1999 - REVISED FEBRUARY 2013 www.ti.com REVISION HISTORY Changes from Revision B (February 2013) to Revision C * 6 Page Changed layout of National Data Sheet to TI format ............................................................................................................ 5 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: DS26LS32AC DS26LS32C DS26LS32M DS26LS33M PACKAGE OPTION ADDENDUM www.ti.com 23-Aug-2017 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) DS26LS32ACM/NOPB LIFEBUY SOIC D 16 48 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS26LS32 ACM DS26LS32ACMX/NOPB LIFEBUY SOIC D 16 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS26LS32 ACM DS26LS32CM/NOPB LIFEBUY SOIC D 16 48 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS26LS32CM DS26LS32CMX/NOPB LIFEBUY SOIC D 16 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 DS26LS32CM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 23-Aug-2017 continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 1-Oct-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant DS26LS32ACMX/NOPB SOIC D 16 2500 330.0 16.4 6.5 10.3 2.3 8.0 16.0 Q1 DS26LS32CMX/NOPB SOIC D 16 2500 330.0 16.4 6.5 10.3 2.3 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 1-Oct-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS26LS32ACMX/NOPB SOIC D 16 2500 367.0 367.0 35.0 DS26LS32CMX/NOPB SOIC D 16 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: DS26LS32CM DS26LS32CM/NOPB DS26LS32CMX DS26LS32CMX/NOPB DS26LS32CN DS26LS32CN/NOPB AM26LS32CN AM26LS32PC