BRUS2 BRUS2F
MINIBRIDGE
50 ns. ULTRA-FAST RECOVERY
SINGLE-PHASE, FULL-WAVE BRIDGES
HEAT SINK CHASSIS P.C. BOARD MOUNTING
PRV/Leg 50V 100V 200V 400V 600V
9.0 AMP SERIES
10.5AMP SERIES
BRUS205 BRUS210 BRUS220 BRUS240 BRUS260
BRUS205F BRUS210F BRUS220F BRUS240F BRUS260F
1.3
200
Volts
5.5 typ.
UNITS
Nanosec.
oC/W
4.5 typ.
1.3
50
200
10 10
50
125
O
IF=2.0
CIR
CIR
FSM (8.3ms)
Max. Forward Voltage Drop, VF@
Max.DC Reverse Current @ PRV and 25 ,
Max.DC Reverse Current @ PRV and 100 ,
Max. Peak Surge Current, l
Average Output Current lF (Av.) TC 60 C (Fig.1) ,
Storage Temperature Range, TSTG
Thermal Resistance (Total Bridge), R0j-c
-
Max. Reverse Recovery Time,Trr (Fig.4)
A
oC
9.0 10.5
-55 to+150
Amps
BRUS2
9 Amps. Wire Leads
BRUS2 BRUS2F
A
Amps
This mark indicates recognition under the component
program of Underwriters Laboratories, inc.
EDI reserves the right to change these specifications at any time without notice.
BRUS 2F
10.5 Amps. Quick-connects
ELECTRICAL CHARACTERISTICS PER LEG
(at TA=25 C U nle ss O the rwis e Sp eci fie d)
125
R R
1, 2 NON-INDUCTIVE RESISTORS
PULSE GENERATOR - HEWLETT
PACKARD 214A OR EQUIV.
IKC REP.RATE, 10 SEC. PULSE WIDTH
ADJUST PULSE AMPLITUDE FOR PEAK IR
TEST CIRCUIT
PULSE
GENERATOR
D.U.T.
SCOPE
R2
1 OHM
R1
50 OHM
+
-
21 GRAY OAKS AVENUE * YONKERS. NEW YORK 10710 914-965-4400 * FAX 914-965-5531 * 1-800-678-0828
ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951.
Ee-mail:sales@edidiodes.com
Wwebsite: http://www.edidiodes.com
*
FIG.1 FIG.2
FIG.3
CURRENT DERATING
6
12
4
8
2
10
0
0 25 50 75 100 125 150
L
lF(AV). AVERAGE FORWARD CURRENT
(AMP )
(OC)
TC=TEMPERATURE NUMBER OF CYCLES AT 60 Hz
1 2 510 20 50 100
500
10
50
100
200
1000
NON-REPETITIVE SURGE CURRENT
PEAK SURGE CURRENT I
BRUS2 BRUS2F
20
BRUS2 SERIES MECH. OUTLINE
+
_
AC
AC
Dielectric test voltage 1500 volts rms, max. 50-60Hz
+_
.463 .015
+_
.463 .015
.85MAX.
1 MIN.
.30 MAX.
EPOXY
METAL BASE
+
.150 DIA
THRU.
_
+
.040 .002 DIA.
BRUS2-F SERIES MECH. OUTLINE
+
.85 MAX.
THRU
AC .30 MAX.
AC
METAL BASE
EPOXY
.50 MAX.
FASTON
4 PLACES
BRUS2F
BRUS2
FSM
1.0A
0.5A
TRR
ZERO
REFERENCE
0.25A
NOTE: A thin film of silicone thermal compound is recommended between the Minibridge
case and mounting surface for improved thermal conduction.
