Series AM15C-NZ 15 Watt | DC-DC Converter FEATURES: Picture coming soon * * * * * * * * * * Wide 2:1 Input Voltage Range High efficiency up to 91% 1500 VDC Isolation Over Current Protection Remote On/Off control Operating Temperature -40C to +105C Output Over Voltage protection Continuous Short Circuit Protection Input Under Voltage Protection Bare Part Meet CISPR32/EN55032 Class A Models Single output Model Input Voltage (VDC) Output Voltage (VDC) Input Current max Full/No Load (mA) Output Current max (mA) Isolation (VDC) Max Capacitive Load (uF) Efficiency Typ. (%) 9-18 9-18 9-18 9-18 9-18 18-36 18-36 18-36 18-36 18-36 36-75 36-75 36-75 36-75 36-75 3.3 5 12 15 24 3.3 5 12 15 24 3.3 5 12 15 24 1280/65 1421/65 1421/22 1405/22 1405/22 647/50 711/50 711/15 703/15 703/20 320/30 356/30 352/11 352/11 352/11 4000 3000 1250 1000 625 4000 3000 1250 1000 625 4000 3000 1250 1000 625 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 1500 4700 4700 1000 820 270 4700 4700 1000 820 270 4700 4700 1000 820 270 88 90 90 91 91 88 90 90 91 91 88 90 91 91 91 AM15C-1203S-NZ AM15C-1205S-NZ AM15C-1212S-NZ AM15C-1215S-NZ AM15C-1224S-NZ AM15C-2403S-NZ AM15C-2405S-NZ AM15C-2412S-NZ AM15C-2415S-NZ AM15C-2424S-NZ AM15C-4803S-NZ AM15C-4805S-NZ AM15C-4812S-NZ AM15C-4815S-NZ AM15C-4824S-NZ NOTE: All specifications in this datasheet are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. Input Specifications Parameters Voltage range Nominal Typical 12 Vin 24 Vin 48 Vin 9-18 18-36 36-75 Filter Maximum Units VDC Pi Absolute Maximum Rating (1s) -0.7 - 25 -0.7 - 50 -0.7 - 100 12 Vin 24 Vin 48 Vin Input reflected ripple current Input Under voltage protection Startup time Remote On/Off Control 30 6.5 15.5 30 10 12 Vin 24 Vin 48 Vin Nominal input, resistive load On Off VDC mA VDC ms 3.5-12VDC or leave open 0-1.2VDC or connect to GND, idle current 2-7mA Isolation Specifications Parameters Tested I/O voltage Resistance Capacitance www.aimtec.com F 051e R1 Conditions Typical 60 sec, <1mA 500VDC I/O, 100KHz/0.1V 1500 2000 Tel: +1 514 620 2722 1 of 5 Maximum Units >1000 VDC MOhm pF Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15C-NZ 15 Watt | DC-DC Converter Output Specifications Parameters Voltage accuracy Over voltage protection Over current protection Short Circuit protection Short circuit restart Line voltage regulation Load voltage regulation Temperature coefficient Ripple & Noise Transient recovery time Transient recovery deviation Conditions Typical 0% to 100% load Maximum Units 3 % % of Vout % of Iout 0.5 1 0.03 100 0.5 7 5 % of Vin % %/oC mV p-p ms % 1 110-160 110-190 Continuous Auto-Recovery 0.2 0.5 Full load, LL to HL 5% to 100% load 100% load 20MHz Bandwidth, 5-100% load 25% load step change 3.3/5V output 25% load step change Others 50 0.3 3 3 General Specifications Parameters Switching frequency Operating temperature Storage temperature Maximum case temperature Cooling Humidity Case material Weight Dimensions (L x W x H) MTBF Maximum soldering temperature Conditions 100% load See derating curve Typical 3.3/5V output Others 3.3/5V output Others -55 to +125 Maximum 300 270 Units KHz -40 to +95 -40 to +105 oC oC 105 oC Free air convection 95 Aluminum Alloy 15 1 x 1 x 0.46 inches 25.40 x 25.40 x 11.70 mm o >1,000,000 hours (MIL-HDBK -217F, Ground Benign, t=+25 C) 1.5mm from case for 10 sec 300 % RH g oC Safety Specifications Parameters Standards Designed to meet EN62368 CISPR32 / EN 55032, Class A, Class B with the recommended EMC circuit Electrostatic Discharge Immunity IEC 61000-4-2, Contact 6KV, Air 8KV, Criteria B RF, Electromagnetic Field Immunity IEC 61000-4-3, 10V/m, Criteria A Electrical Fast Transient / Burst Immunity IEC 61000-4-4, 2KV with the recommended EMC circuit, Criteria A Surge Immunity IEC 61000-4-5, L-L 2KV with the recommended EMC circuit, Criteria B RF, Conducted Disturbance Immunity IEC 61000-4-6, 3 Vrms, Criteria A Pin Out Specifications Pin 1 2 3 4 5 6 Single +V Input -V Input On/Off Control +V Output Trim -V Output www.aimtec.com F 051e R1 Tel: +1 514 620 2722 2 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15C-NZ 15 Watt | DC-DC Converter Dimensions Bottom View Top View 2.54 (0.10) 25.40 (1.00) 2.54 10.16 (0.10) (0.40) 10.16 (0.40) 5 4 6 20.32 (0.80) 25.40 (1.00) +V Output Trim +V -V Input Input CTRL 2.54 (0.10) 1 Side View -V Output 2 3 7.62 (0.30) 10.16 (0.40) 5.08 (0.20) 9.90 (0.39) Printed Face 2.54 (0.10) Dimensions mm (inch) Case Tolerance 0.50 (0.02) Pin Diameter 1.0 0.10 (0.04 0.004) 1.00 (0.39) Derating Free Air Convection 3.3V/5V Output 12V/15V/24V Output Output Power (%) 100 80 60 Safe Operating Area 40 20 0 - 40 - 20 0 20 40 60 75 95 80 105 100 Ambient Temperature C Typical Application Circuits + Vin + Vin C1 100uF DC Model C2 www.aimtec.com F 051e R1 +Vout DC C2 - Vin - Vin + Vout 3.3V/5V/12V/15V Vout 100F - Vout - Vout 24V Vout 47F Tel: +1 514 620 2722 3 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15C-NZ 15 Watt | DC-DC Converter Recommended EMC Circuits CY1 1nF/2KV LDM FUSE + Vin + Vout + Vin + +Vout + C2 C1 DC C4 C3 DC - Vin - Vin C5 - Vout - Vout CY2 1nF/2KV Model FUSE C1, C4 C2, C3 LDM C5 12V/24V Vin 48V Vin Choose based on actual input current 330F/50V 330F/100V 4.7F/50V 4.7F/100V 2.2h/4A 2.2H/2A Refer to the C2 in typical application circuit Trimming Output voltage can be externally trimmed by utilizing the methods as shown below Fixed Resistor Variable Potentiometer Leave open if not used. 3.3V output models Trim down % Vout (VDC) Rt down (K) Trim up % Vout (VDC) Rt up (K) www.aimtec.com F 051e R1 1 2 3 4 5 6 7 8 9 10 3.267 3.234 3.201 3.168 3.135 3.102 3.069 3.036 3.003 2.97 190.744 104.218 68.096 48.270 35.741 27.108 20.797 15.983 12.190 9.124 1 2 3 4 5 6 7 8 9 10 3.333 3.366 3.399 3.432 3.465 3.498 3.531 3.564 3.597 3.63 303.349 100.149 55.286 35.580 24.504 17.407 12.472 8.842 6.058 3.857 Tel: +1 514 620 2722 4 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only Series AM15C-NZ 15 Watt | DC-DC Converter 5V output models Trim down % 1 2 3 4 5 6 7 8 9 10 4.95 4.9 4.85 4.8 4.75 4.7 4.65 4.6 4.55 4.5 89.996 47.446 29.793 20.131 14.036 9.840 6.775 4.439 2.598 1.111 1 2 3 4 5 6 7 8 9 10 5.05 5.1 5.15 5.2 5.25 5.3 5.35 5.4 5.45 5.5 238.676 81.473 46.044 30.398 21.581 15.923 11.985 9.085 6.861 5.101 1 2 3 4 5 6 7 8 9 10 11.88 11.76 11.64 11.52 11.4 11.28 11.16 11.04 10.92 10.8 493.692 299.052 210.127 159.185 126.173 103.042 85.932 72.764 62.316 53.823 1 2 3 4 5 6 7 8 9 10 12.12 12.24 12.36 12.48 12.6 12.72 12.84 12.96 13.08 13.2 704.035 156.520 81.479 51.675 35.677 25.695 18.874 13.917 10.152 7.195 1 2 3 4 5 6 7 8 9 10 14.85 14.7 14.55 14.4 14.25 14.1 13.95 13.8 13.65 13.5 632.483 398.237 286.114 220.359 177.137 146.560 123.787 106.169 92.132 80.687 1 2 3 4 5 6 7 8 9 10 15.15 15.3 15.45 15.6 15.75 15.9 16.05 16.2 16.35 16.5 1457.699 190.174 94.242 58.954 40.616 29.381 21.791 16.321 12.190 8.961 1 2 3 4 5 6 7 8 9 10 23.76 23.52 23.28 23.04 22.8 22.56 22.32 22.08 21.84 21.6 1284.000 789.923 563.667 433.904 349.754 290.763 247.115 213.514 186.847 165.170 1 2 3 4 5 6 7 8 9 10 24.24 24.48 24.72 24.96 25.2 25.44 25.68 25.92 26.16 26.4 814.689 177.714 92.138 58.264 40.107 28.788 21.057 15.440 11.176 7.827 Vout (VDC) Rt down (K) Trim up % Vout (VDC) Rt up (K) 12V output models Trim down % Vout (VDC) Rt down (K) Trim up % Vout (VDC) Rt up (K) 15V output models Trim down % Vout (VDC) Rt down (K) Trim up % Vout (VDC) Rt up (K) 24V output models Trim down % Vout (VDC) Rt down (K) Trim up % Vout (VDC) Rt up (K) NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25C, humidity<75%, nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec's standard Terms of Sale available at www.aimtec.com. www.aimtec.com F 051e R1 Tel: +1 514 620 2722 5 of 5 Toll free: + 1 888 9 AIMTEC (924 6832) North America only