Freescale Semiconductor Data Sheet: Technical Data K10 Sub-Family Document Number: K10P121M100SF2V2 Rev. 3, 6/2013 K10P121M100SF2V2 Supports the following: MK10DN512VMC10 Features * Operating Characteristics - Voltage range: 1.71 to 3.6 V - Flash write voltage range: 1.71 to 3.6 V - Temperature range (ambient): -40 to 105C * Performance - Up to 100 MHz ARM Cortex-M4 core with DSP instructions delivering 1.25 Dhrystone MIPS per MHz * Memories and memory interfaces - Up to 512 KB program flash memory on nonFlexMemory devices - Up to 128 KB RAM - Serial programming interface (EzPort) - FlexBus external bus interface * Clocks - 3 to 32 MHz crystal oscillator - 32 kHz crystal oscillator - Multi-purpose clock generator * System peripherals - Multiple low-power modes to provide power optimization based on application requirements - Memory protection unit with multi-master protection - 16-channel DMA controller, supporting up to 63 request sources - External watchdog monitor - Software watchdog - Low-leakage wakeup unit * Human-machine interface - Low-power hardware touch sensor interface (TSI) - General-purpose input/output * Analog modules - Two 16-bit SAR ADCs - Programmable gain amplifier (PGA) (up to x64) integrated into each ADC - Two 12-bit DACs - Two transimpedance amplifiers - Three analog comparators (CMP) containing a 6-bit DAC and programmable reference input - Voltage reference * Timers - Programmable delay block - Eight-channel motor control/general purpose/PWM timer - Two 2-channel quadrature decoder/general purpose timers - Periodic interrupt timers - 16-bit low-power timer - Carrier modulator transmitter - Real-time clock * Communication interfaces - Two Controller Area Network (CAN) modules - Three SPI modules - Two I2C modules - Six UART modules - Secure Digital host controller (SDHC) - I2S module * Security and integrity modules - Hardware CRC module to support fast cyclic redundancy checks - 128-bit unique identification (ID) number per chip Freescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products. (c) 2012-2013 Freescale Semiconductor, Inc. Table of Contents 1 Ordering parts...........................................................................3 5.4.2 Thermal attributes.................................................21 1.1 Determining valid orderable parts......................................3 6 Peripheral operating requirements and behaviors....................22 2 Part identification......................................................................3 6.1 Core modules....................................................................22 2.1 Description.........................................................................3 6.1.1 Debug trace timing specifications.........................22 2.2 Format...............................................................................3 6.1.2 JTAG electricals....................................................23 2.3 Fields.................................................................................3 6.2 System modules................................................................26 2.4 Example............................................................................4 6.3 Clock modules...................................................................26 3 Terminology and guidelines......................................................4 6.3.1 MCG specifications...............................................26 3.1 Definition: Operating requirement......................................4 6.3.2 Oscillator electrical specifications.........................28 3.2 Definition: Operating behavior...........................................5 6.3.3 32 kHz oscillator electrical characteristics.............30 3.3 Definition: Attribute............................................................5 6.4 Memories and memory interfaces.....................................31 3.4 Definition: Rating...............................................................6 6.4.1 Flash electrical specifications................................31 3.5 Result of exceeding a rating..............................................6 6.4.2 EzPort switching specifications.............................33 3.6 Relationship between ratings and operating 6.4.3 Flexbus switching specifications...........................34 requirements......................................................................6 6.5 Security and integrity modules..........................................37 3.7 Guidelines for ratings and operating requirements............7 6.6 Analog...............................................................................37 3.8 Definition: Typical value.....................................................7 6.6.1 ADC electrical specifications.................................37 3.9 Typical value conditions....................................................8 6.6.2 CMP and 6-bit DAC electrical specifications.........45 4 Ratings......................................................................................9 6.6.3 12-bit DAC electrical characteristics.....................48 4.1 Thermal handling ratings...................................................9 6.6.4 Voltage reference electrical specifications............51 4.2 Moisture handling ratings..................................................9 6.7 Timers................................................................................52 4.3 ESD handling ratings.........................................................9 6.8 Communication interfaces.................................................52 4.4 Voltage and current operating ratings...............................9 6.8.1 CAN switching specifications................................52 5 General.....................................................................................10 6.8.2 DSPI switching specifications (limited voltage 5.1 AC electrical characteristics..............................................10 5.2 Nonswitching electrical specifications...............................10 range)....................................................................53 6.8.3 DSPI switching specifications (full voltage range).54 5.2.1 Voltage and current operating requirements.........10 6.8.4 Inter-Integrated Circuit Interface (I2C) timing........56 5.2.2 LVD and POR operating requirements.................11 6.8.5 UART switching specifications..............................57 5.2.3 Voltage and current operating behaviors..............12 6.8.6 SDHC specifications.............................................57 5.2.4 Power mode transition operating behaviors..........14 6.8.7 I2S/SAI switching specifications............................58 5.2.5 Power consumption operating behaviors..............15 5.2.6 EMC radiated emissions operating behaviors.......18 5.2.7 Designing with radiated emissions in mind...........19 7 Dimensions...............................................................................65 5.2.8 Capacitance attributes..........................................19 7.1 Obtaining package dimensions.........................................65 5.3 Switching specifications.....................................................19 8 Pinout........................................................................................65 6.9 Human-machine interfaces (HMI)......................................64 6.9.1 TSI electrical specifications...................................64 5.3.1 Device clock specifications...................................19 8.1 K10 signal multiplexing and pin assignments....................65 5.3.2 General switching specifications...........................20 8.2 K10 pinouts.......................................................................70 5.4 Thermal specifications.......................................................21 9 Revision history.........................................................................71 5.4.1 Thermal operating requirements...........................21 K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 2 Freescale Semiconductor, Inc. Ordering parts 1 Ordering parts 1.1 Determining valid orderable parts Valid orderable part numbers are provided on the web. To determine the orderable part numbers for this device, go to freescale.com and perform a part number search for the following device numbers: PK10 and MK10 . 2 Part identification 2.1 Description Part numbers for the chip have fields that identify the specific part. You can use the values of these fields to determine the specific part you have received. 2.2 Format Part numbers for this device have the following format: Q K## A M FFF R T PP CC N 2.3 Fields This table lists the possible values for each field in the part number (not all combinations are valid): Field Description Values Q Qualification status * M = Fully qualified, general market flow * P = Prequalification K## Kinetis family * K10 A Key attribute * D = Cortex-M4 w/ DSP * F = Cortex-M4 w/ DSP and FPU M Flash memory type * N = Program flash only * X = Program flash and FlexMemory Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 3 Terminology and guidelines Field Description Values FFF Program flash memory size * * * * * * * 32 = 32 KB 64 = 64 KB 128 = 128 KB 256 = 256 KB 512 = 512 KB 1M0 = 1 MB 2M0 = 2 MB R Silicon revision * Z = Initial * (Blank) = Main * A = Revision after main T Temperature range (C) * V = -40 to 105 * C = -40 to 85 PP Package identifier * * * * * * * * * * * FM = 32 QFN (5 mm x 5 mm) FT = 48 QFN (7 mm x 7 mm) LF = 48 LQFP (7 mm x 7 mm) LH = 64 LQFP (10 mm x 10 mm) MP = 64 MAPBGA (5 mm x 5 mm) LK = 80 LQFP (12 mm x 12 mm) LL = 100 LQFP (14 mm x 14 mm) MC = 121 MAPBGA (8 mm x 8 mm) LQ = 144 LQFP (20 mm x 20 mm) MD = 144 MAPBGA (13 mm x 13 mm) MJ = 256 MAPBGA (17 mm x 17 mm) CC Maximum CPU frequency (MHz) * * * * * 5 = 50 MHz 7 = 72 MHz 10 = 100 MHz 12 = 120 MHz 15 = 150 MHz N Packaging type * R = Tape and reel * (Blank) = Trays 2.4 Example This is an example part number: MK10DN512ZVMD10 3 Terminology and guidelines 3.1 Definition: Operating requirement An operating requirement is a specified value or range of values for a technical characteristic that you must guarantee during operation to avoid incorrect operation and possibly decreasing the useful life of the chip. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 4 Freescale Semiconductor, Inc. Terminology and guidelines 3.1.1 Example This is an example of an operating requirement: Symbol VDD Description 1.0 V core supply voltage Min. 0.9 Max. 1.1 Unit V 3.2 Definition: Operating behavior An operating behavior is a specified value or range of values for a technical characteristic that are guaranteed during operation if you meet the operating requirements and any other specified conditions. 3.2.1 Example This is an example of an operating behavior: Symbol IWP Description Min. Digital I/O weak pullup/ 10 pulldown current Max. 130 Unit A 3.3 Definition: Attribute An attribute is a specified value or range of values for a technical characteristic that are guaranteed, regardless of whether you meet the operating requirements. 3.3.1 Example This is an example of an attribute: Symbol CIN_D Description Input capacitance: digital pins Min. -- Max. 7 Unit pF K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 5 Terminology and guidelines 3.4 Definition: Rating A rating is a minimum or maximum value of a technical characteristic that, if exceeded, may cause permanent chip failure: * Operating ratings apply during operation of the chip. * Handling ratings apply when the chip is not powered. 3.4.1 Example This is an example of an operating rating: Symbol VDD Description 1.0 V core supply voltage Min. -0.3 Max. 1.2 Unit V 3.5 Result of exceeding a rating Failures in time (ppm) 40 30 The likelihood of permanent chip failure increases rapidly as soon as a characteristic begins to exceed one of its operating ratings. 20 10 0 Operating rating Measured characteristic K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 6 Freescale Semiconductor, Inc. Terminology and guidelines 3.6 Relationship between ratings and operating requirements g tin ng ati ( n me r a (m nt me e Op e uir eq gr n i rat era Op x.) ) in. t (m n.) mi t era Op ing x.) e uir req ng ati gr tin a (m ra e Op Fatal range Degraded operating range Normal operating range Degraded operating range Fatal range Expected permanent failure - No permanent failure - Possible decreased life - Possible incorrect operation - No permanent failure - Correct operation - No permanent failure - Possible decreased life - Possible incorrect operation Expected permanent failure - Operating (power on) g lin nd ing rat (m x.) ) in. a (m ng ati r g dlin n Ha Ha Fatal range Handling range Fatal range Expected permanent failure No permanent failure Expected permanent failure - Handling (power off) 3.7 Guidelines for ratings and operating requirements Follow these guidelines for ratings and operating requirements: * Never exceed any of the chip's ratings. * During normal operation, don't exceed any of the chip's operating requirements. * If you must exceed an operating requirement at times other than during normal operation (for example, during power sequencing), limit the duration as much as possible. 3.8 Definition: Typical value A typical value is a specified value for a technical characteristic that: * Lies within the range of values specified by the operating behavior * Given the typical manufacturing process, is representative of that characteristic during operation when you meet the typical-value conditions or other specified conditions Typical values are provided as design guidelines and are neither tested nor guaranteed. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 7 Terminology and guidelines 3.8.1 Example 1 This is an example of an operating behavior that includes a typical value: Symbol Description IWP Digital I/O weak pullup/pulldown current Min. 10 Typ. 70 Max. 130 Unit A 3.8.2 Example 2 This is an example of a chart that shows typical values for various voltage and temperature conditions: 5000 4500 4000 TJ IDD_STOP (A) 3500 150 C 3000 105 C 2500 25 C 2000 -40 C 1500 1000 500 0 0.90 0.95 1.00 1.05 1.10 VDD (V) 3.9 Typical value conditions Typical values assume you meet the following conditions (or other conditions as specified): Symbol Description Value Unit TA Ambient temperature 25 C VDD 3.3 V supply voltage 3.3 V K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 8 Freescale Semiconductor, Inc. Ratings 4 Ratings 4.1 Thermal handling ratings Symbol Description Min. Max. Unit Notes TSTG Storage temperature -55 150 C 1 TSDR Solder temperature, lead-free -- 260 C 2 1. Determined according to JEDEC Standard JESD22-A103, High Temperature Storage Life. 2. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices. 4.2 Moisture handling ratings Symbol MSL Description Moisture sensitivity level Min. Max. Unit Notes -- 3 -- 1 1. Determined according to IPC/JEDEC Standard J-STD-020, Moisture/Reflow Sensitivity Classification for Nonhermetic Solid State Surface Mount Devices. 4.3 ESD handling ratings Symbol Description Min. Max. Unit Notes VHBM Electrostatic discharge voltage, human body model -2000 +2000 V 1 VCDM Electrostatic discharge voltage, charged-device model -500 +500 V 2 Latch-up current at ambient temperature of 105C -100 +100 mA 3 ILAT 1. Determined according to JEDEC Standard JESD22-A114, Electrostatic Discharge (ESD) Sensitivity Testing Human Body Model (HBM). 2. Determined according to JEDEC Standard JESD22-C101, Field-Induced Charged-Device Model Test Method for Electrostatic-Discharge-Withstand Thresholds of Microelectronic Components. 3. Determined according to JEDEC Standard JESD78, IC Latch-Up Test. 4.4 Voltage and current operating ratings K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 9 General Symbol Description Min. Max. Unit VDD Digital supply voltage -0.3 3.8 V IDD Digital supply current -- 185 mA VDIO Digital input voltage (except RESET, EXTAL, and XTAL) -0.3 5.5 V VAIO Analog1, RESET, EXTAL, and XTAL input voltage -0.3 VDD + 0.3 V Maximum current single pin limit (applies to all digital pins) -25 25 mA VDD - 0.3 VDD + 0.3 V -0.3 3.8 V ID VDDA Analog supply voltage VBAT RTC battery supply voltage 1. Analog pins are defined as pins that do not have an associated general purpose I/O port function. 5 General 5.1 AC electrical characteristics Unless otherwise specified, propagation delays are measured from the 50% to the 50% point, and rise and fall times are measured at the 20% and 80% points, as shown in the following figure. Figure 1. Input signal measurement reference All digital I/O switching characteristics assume: 1. output pins * have CL=30pF loads, * are configured for fast slew rate (PORTx_PCRn[SRE]=0), and * are configured for high drive strength (PORTx_PCRn[DSE]=1) 2. input pins * have their passive filter disabled (PORTx_PCRn[PFE]=0) 5.2 Nonswitching electrical specifications K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 10 Freescale Semiconductor, Inc. General 5.2.1 Voltage and current operating requirements Table 1. Voltage and current operating requirements Symbol Description Min. Max. Unit VDD Supply voltage 1.71 3.6 V VDDA Analog supply voltage 1.71 3.6 V VDD - VDDA VDD-to-VDDA differential voltage -0.1 0.1 V VSS - VSSA VSS-to-VSSA differential voltage -0.1 0.1 V 1.71 3.6 V * 2.7 V VDD 3.6 V 0.7 x VDD -- V * 1.7 V VDD 2.7 V 0.75 x VDD -- V * 2.7 V VDD 3.6 V -- 0.35 x VDD V * 1.7 V VDD 2.7 V -- 0.3 x VDD V 0.06 x VDD -- V -5 -- mA VBAT VIH VIL RTC battery supply voltage Input high voltage Input low voltage VHYS Input hysteresis IICDIO Digital pin negative DC injection current -- single pin * VIN < VSS-0.3V IICAIO IICcont 1 Analog2, EXTAL, and XTAL pin DC injection current -- single pin 3 mA * VIN < VSS-0.3V (Negative current injection) -5 -- * VIN > VDD+0.3V (Positive current injection) -- +5 -25 -- -- +25 Contiguous pin DC injection current --regional limit, includes sum of negative injection currents or sum of positive injection currents of 16 contiguous pins * Negative current injection * Positive current injection mA VODPU Open drain pullup voltage level VDD VDD V VRAM VDD voltage required to retain RAM 1.2 -- V VPOR_VBAT -- V VRFVBAT Notes VBAT voltage required to retain the VBAT register file 4 1. All 5 V tolerant digital I/O pins are internally clamped to VSS through an ESD protection diode. There is no diode connection to VDD. If VIN is less than VDIO_MIN, a current limiting resistor is required. The negative DC injection current limiting resistor is calculated as R=(VDIO_MIN-VIN)/|IICDIO|. 2. Analog pins are defined as pins that do not have an associated general purpose I/O port function. Additionally, EXTAL and XTAL are analog pins. 3. All analog pins are internally clamped to VSS and VDD through ESD protection diodes. If VIN is less than VAIO_MIN or greater than VAIO_MAX, a current limiting resistor is required. The negative DC injection current limiting resistor is calculated as R=(VAIO_MIN-VIN)/|IICAIO|. The positive injection current limiting resistor is calculated as R=(VIN-VAIO_MAX)/|IICAIO|. Select the larger of these two calculated resistances if the pin is exposed to positive and negative injection currents. 4. Open drain outputs must be pulled to VDD. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 11 General 5.2.2 LVD and POR operating requirements Table 2. VDD supply LVD and POR operating requirements Symbol Description Min. Typ. Max. Unit VPOR Falling VDD POR detect voltage 0.8 1.1 1.5 V VLVDH Falling low-voltage detect threshold -- high range (LVDV=01) 2.48 2.56 2.64 V Low-voltage warning thresholds -- high range 1 VLVW1H * Level 1 falling (LVWV=00) 2.62 2.70 2.78 V VLVW2H * Level 2 falling (LVWV=01) 2.72 2.80 2.88 V VLVW3H * Level 3 falling (LVWV=10) 2.82 2.90 2.98 V VLVW4H * Level 4 falling (LVWV=11) 2.92 3.00 3.08 V -- 80 -- mV 1.54 1.60 1.66 V VHYSH Low-voltage inhibit reset/recover hysteresis -- high range VLVDL Falling low-voltage detect threshold -- low range (LVDV=00) Low-voltage warning thresholds -- low range 1 VLVW1L * Level 1 falling (LVWV=00) 1.74 1.80 1.86 V VLVW2L * Level 2 falling (LVWV=01) 1.84 1.90 1.96 V VLVW3L * Level 3 falling (LVWV=10) 1.94 2.00 2.06 V VLVW4L * Level 4 falling (LVWV=11) 2.04 2.10 2.16 V -- 60 -- mV VHYSL Low-voltage inhibit reset/recover hysteresis -- low range Notes VBG Bandgap voltage reference 0.97 1.00 1.03 V tLPO Internal low power oscillator period -- factory trimmed 900 1000 1100 s 1. Rising thresholds are falling threshold + hysteresis voltage Table 3. VBAT power operating requirements Symbol Description VPOR_VBAT Falling VBAT supply POR detect voltage Min. Typ. Max. Unit 0.8 1.1 1.5 V Notes K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 12 Freescale Semiconductor, Inc. General 5.2.3 Voltage and current operating behaviors Table 4. Voltage and current operating behaviors Symbol VOH Min. Typ.1 Max. Unit * 2.7 V VDD 3.6 V, IOH = -9mA VDD - 0.5 -- -- V * 1.71 V VDD 2.7 V, IOH = -3mA VDD - 0.5 -- -- V * 2.7 V VDD 3.6 V, IOH = -2mA VDD - 0.5 -- -- V * 1.71 V VDD 2.7 V, IOH = -0.6mA VDD - 0.5 -- -- V -- -- 100 mA Description Notes Output high voltage -- high drive strength Output high voltage -- low drive strength IOHT Output high current total for all ports VOL Output low voltage -- high drive strength 2 * 2.7 V VDD 3.6 V, IOL = 10mA -- -- 0.5 V * 1.71 V VDD 2.7 V, IOL = 5mA -- -- 0.5 V * 2.7 V VDD 3.6 V, IOL = 2mA -- -- 0.5 V * 1.71 V VDD 2.7 V, IOL = 1mA -- -- 0.5 V -- -- 100 mA Output low voltage -- low drive strength IOLT Output low current total for all ports IINA Input leakage current, analog pins and digital pins configured as analog inputs 3, 4 * VSS VIN VDD * All pins except EXTAL32, XTAL32, EXTAL, XTAL * EXTAL (PTA18) and XTAL (PTA19) * EXTAL32, XTAL32 IIND -- 0.002 0.5 A -- 0.004 1.5 A -- 0.075 10 A Input leakage current, digital pins 4, 5 * VSS VIN VIL * All digital pins -- 0.002 0.5 A -- 0.002 0.5 A -- 0.004 1 A * VIN = VDD * All digital pins except PTD7 * PTD7 IIND Input leakage current, digital pins 4, 5, 6 * VIL < VIN < VDD * VDD = 3.6 V -- 18 26 A * VDD = 3.0 V -- 12 49 A * VDD = 2.5 V -- 8 13 A * VDD = 1.7 V -- 3 6 A Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 13 General Table 4. Voltage and current operating behaviors (continued) Symbol IIND Description Min. Max. Unit Input leakage current, digital pins * VDD < VIN < 5.5 V ZIND Typ.1 Notes 4, 5 -- 1 50 A Input impedance examples, digital pins 4, 7 * VDD = 3.6 V -- -- 48 k * VDD = 3.0 V -- -- 55 k * VDD = 2.5 V -- -- 57 k * VDD = 1.7 V -- -- 85 k RPU Internal pullup resistors 20 35 50 k 8 RPD Internal pulldown resistors 20 35 50 k 9 1. 2. 3. 4. 5. 6. 7. Typical values characterized at 25C and VDD = 3.6 V unless otherwise noted. Open drain outputs must be pulled to VDD. Analog pins are defined as pins that do not have an associated general purpose I/O port function. Digital pins have an associated GPIO port function and have 5V tolerant inputs, except EXTAL and XTAL. Internal pull-up/pull-down resistors disabled. Characterized, not tested in production. Examples calculated using VIL relation, VDD, and max IIND: ZIND=VIL/IIND. This is the impedance needed to pull a high signal to a level below VIL due to leakage when VIL < VIN < VDD. These examples assume signal source low = 0 V. 8. Measured at VDD supply voltage = VDD min and Vinput = VSS 9. Measured at VDD supply voltage = VDD min and Vinput = VDD I IND Digital input Source + - Z IND 5.2.4 Power mode transition operating behaviors All specifications except tPOR, and VLLSxRUN recovery times in the following table assume this clock configuration: * * * * * CPU and system clocks = 100 MHz Bus clock = 50 MHz FlexBus clock = 50 MHz Flash clock = 25 MHz MCG mode: FEI K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 14 Freescale Semiconductor, Inc. General Table 5. Power mode transition operating behaviors Symbol tPOR Description Min. Max. After a POR event, amount of time from the point VDD reaches 1.71 V to execution of the first instruction across the operating temperature range of the chip. Unit Notes 1 * VDD slew rate 5.7 kV/s * VDD slew rate < 5.7 kV/s * VLLS1 RUN * VLLS2 RUN * VLLS3 RUN * LLS RUN * VLPS RUN * STOP RUN s -- 300 -- 1.7 V / (VDD slew rate) -- 130 s -- 92 s -- 92 s -- 5.9 s -- 5.0 s -- 5.0 s 1. Normal boot (FTFL_OPT[LPBOOT]=1) 5.2.5 Power consumption operating behaviors Table 6. Power consumption operating behaviors Symbol IDDA IDD_RUN Description Analog supply current Typ. Max. Unit Notes -- -- See note mA 1 Run mode current -- all peripheral clocks disabled, code executing from flash * @ 1.8V * @ 3.0V IDD_RUN Min. 2 -- 37 63 mA -- 38 64 mA Run mode current -- all peripheral clocks enabled, code executing from flash * @ 1.8V * @ 3.0V * @ 25C 3, 4 -- 46 77 mA -- 47 63 mA -- 58 79 mA * @ 125C IDD_WAIT Wait mode high frequency current at 3.0 V -- all peripheral clocks disabled -- 20 -- mA 2 IDD_WAIT Wait mode reduced frequency current at 3.0 V -- all peripheral clocks disabled -- 9 -- mA 5 IDD_VLPR Very-low-power run mode current at 3.0 V -- all peripheral clocks disabled -- 1.12 -- mA 6 Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 15 General Table 6. Power consumption operating behaviors (continued) Symbol Description Min. Typ. Max. Unit Notes IDD_VLPR Very-low-power run mode current at 3.0 V -- all peripheral clocks enabled -- 1.71 -- mA 7 IDD_VLPW Very-low-power wait mode current at 3.0 V -- all peripheral clocks disabled -- 0.77 -- mA 8 IDD_STOP Stop mode current at 3.0 V * @ -40 to 25C -- 0.74 1.41 mA * @ 70C -- 2.45 11.5 mA * @ 105C -- 6.61 30 mA * @ -40 to 25C -- 83 435 A * @ 70C -- 425 2000 A * @ 105C -- 1280 4000 A IDD_VLPS IDD_LLS IDD_VLLS3 IDD_VLLS2 IDD_VLLS1 IDD_VBAT Very-low-power stop mode current at 3.0 V Low leakage stop mode current at 3.0 V 9 * @ -40 to 25C -- 4.58 19.9 A * @ 70C -- 30.6 105 A * @ 105C -- 137 500 A Very low-leakage stop mode 3 current at 3.0 V 9 * @ -40 to 25C -- 3.0 23 A * @ 70C -- 18.6 43 A * @ 105C -- 84.9 230 A * @ -40 to 25C -- 2.2 5.4 A * @ 70C -- 9.3 35 A * @ 105C -- 41.4 128 A * @ -40 to 25C -- 2.1 9 A * @ 70C -- 7.6 28 A * @ 105C -- 33.5 95.5 A -- 0.19 0.22 A -- 0.49 0.64 A -- 2.2 3.2 A Very low-leakage stop mode 2 current at 3.0 V Very low-leakage stop mode 1 current at 3.0 V Average current with RTC and 32kHz disabled at 3.0 V * @ -40 to 25C * @ 70C * @ 105C Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 16 Freescale Semiconductor, Inc. General Table 6. Power consumption operating behaviors (continued) Symbol Description Min. IDD_VBAT Average current when CPU is not accessing RTC registers Typ. Max. Unit Notes 10 * @ 1.8V * @ -40 to 25C * @ 70C * @ 105C -- 0.57 0.67 A -- 0.90 1.2 A -- 2.4 3.5 A -- 0.67 0.94 A -- 1.0 1.4 A -- 2.7 3.9 A * @ 3.0V * @ -40 to 25C * @ 70C * @ 105C 1. The analog supply current is the sum of the active or disabled current for each of the analog modules on the device. See each module's specification for its supply current. 2. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock . MCG configured for FEI mode. All peripheral clocks disabled. 3. 100MHz core and system clock, 50MHz bus and FlexBus clock, and 25MHz flash clock. MCG configured for FEI mode. All peripheral clocks enabled. 4. Max values are measured with CPU executing DSP instructions. 5. 25MHz core and system clock, 25MHz bus clock, and 12.5MHz FlexBus and flash clock. MCG configured for FEI mode. 6. 4 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks disabled. Code executing from flash. 7. 4 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks enabled but peripherals are not in active operation. Code executing from flash. 8. 4 MHz core, system, FlexBus, and bus clock and 1MHz flash clock. MCG configured for BLPE mode. All peripheral clocks disabled. 9. Data reflects devices with 128 KB of RAM. 10. Includes 32kHz oscillator current and RTC operation. 5.2.5.1 Diagram: Typical IDD_RUN operating behavior The following data was measured under these conditions: * MCG in FBE mode for 50 MHz and lower frequencies. MCG in FEE mode at greater than 50 MHz frequencies. * No GPIOs toggled * Code execution from flash with cache enabled * For the ALLOFF curve, all peripheral clocks are disabled except FTFL K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 17 General Figure 2. Run mode supply current vs. core frequency 5.2.6 EMC radiated emissions operating behaviors Table 7. EMC radiated emissions operating behaviors for 144LQFP and 144MAPBGA Symbol Description Frequency band (MHz) 144LQFP 144MAPBGA Unit Notes 1, 2 VRE1 Radiated emissions voltage, band 1 0.15-50 23 12 dBV VRE2 Radiated emissions voltage, band 2 50-150 27 24 dBV VRE3 Radiated emissions voltage, band 3 150-500 28 27 dBV VRE4 Radiated emissions voltage, band 4 500-1000 14 11 dBV IEC level 0.15-1000 K K -- VRE_IEC 2, 3 1. Determined according to IEC Standard 61967-1, Integrated Circuits - Measurement of Electromagnetic Emissions, 150 kHz to 1 GHz Part 1: General Conditions and Definitions and IEC Standard 61967-2, Integrated Circuits - Measurement of Electromagnetic Emissions, 150 kHz to 1 GHz Part 2: Measurement of Radiated Emissions--TEM Cell and Wideband TEM Cell Method. Measurements were made while the microcontroller was running basic application code. The reported emission level is the value of the maximum measured emission, rounded up to the next whole number, from among the measured orientations in each frequency range. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 18 Freescale Semiconductor, Inc. General 2. VDD = 3.3 V, TA = 25 C, fOSC = 12 MHz (crystal), fSYS = 96 MHz, fBUS = 48 MHz 3. Specified according to Annex D of IEC Standard 61967-2, Measurement of Radiated Emissions--TEM Cell and Wideband TEM Cell Method 5.2.7 Designing with radiated emissions in mind To find application notes that provide guidance on designing your system to minimize interference from radiated emissions: 1. Go to www.freescale.com. 2. Perform a keyword search for "EMC design." 5.2.8 Capacitance attributes Table 8. Capacitance attributes Symbol Description Min. Max. Unit CIN_A Input capacitance: analog pins -- 7 pF CIN_D Input capacitance: digital pins -- 7 pF 5.3 Switching specifications 5.3.1 Device clock specifications Table 9. Device clock specifications Symbol Description Min. Max. Unit Notes Normal run mode fSYS System and core clock -- 100 MHz fBUS Bus clock -- 50 MHz FB_CLK FlexBus clock -- 50 MHz fFLASH Flash clock -- 25 MHz fLPTMR LPTMR clock -- 25 MHz VLPR mode1 fSYS System and core clock -- 4 MHz fBUS Bus clock -- 4 MHz FlexBus clock -- 4 MHz fFLASH Flash clock -- 1 MHz fERCLK External reference clock -- 16 MHz LPTMR clock -- 25 MHz FB_CLK fLPTMR_pin Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 19 General Table 9. Device clock specifications (continued) Symbol Description fLPTMR_ERCLK LPTMR external reference clock fFlexCAN_ERCLK FlexCAN external reference clock Min. Max. Unit -- 16 MHz -- 8 MHz fI2S_MCLK I2S master clock -- 12.5 MHz fI2S_BCLK I2S bit clock -- 4 MHz Notes 1. The frequency limitations in VLPR mode here override any frequency specification listed in the timing specification for any other module. 5.3.2 General switching specifications These general purpose specifications apply to all signals configured for GPIO, UART, CAN, CMT, and I2C signals. Table 10. General switching specifications Symbol Description Min. Max. Unit Notes GPIO pin interrupt pulse width (digital glitch filter disabled) -- Synchronous path 1.5 -- Bus clock cycles 1, 2 GPIO pin interrupt pulse width (digital glitch filter disabled, analog filter enabled) -- Asynchronous path 100 -- ns 3 GPIO pin interrupt pulse width (digital glitch filter disabled, analog filter disabled) -- Asynchronous path 16 -- ns 3 External reset pulse width (digital glitch filter disabled) 100 -- ns 3 2 -- Bus clock cycles Mode select (EZP_CS) hold time after reset deassertion Port rise and fall time (high drive strength) 4 * Slew disabled * 1.71 VDD 2.7V -- 12 ns * 2.7 VDD 3.6V -- 6 ns * 1.71 VDD 2.7V -- 36 ns * 2.7 VDD 3.6V -- 24 ns * Slew enabled Port rise and fall time (low drive strength) 5 * Slew disabled * 1.71 VDD 2.7V -- 12 ns * 2.7 VDD 3.6V -- 6 ns * 1.71 VDD 2.7V -- 36 ns * 2.7 VDD 3.6V -- 24 ns * Slew enabled K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 20 Freescale Semiconductor, Inc. General 1. This is the minimum pulse width that is guaranteed to pass through the pin synchronization circuitry. Shorter pulses may or may not be recognized. In Stop, VLPS, LLS, and VLLSx modes, the synchronizer is bypassed so shorter pulses can be recognized in that case. 2. The greater synchronous and asynchronous timing must be met. 3. This is the minimum pulse width that is guaranteed to be recognized as a pin interrupt request in Stop, VLPS, LLS, and VLLSx modes. 4. 75 pF load 5. 15 pF load 5.4 Thermal specifications 5.4.1 Thermal operating requirements Table 11. Thermal operating requirements Symbol Description Min. Max. Unit TJ Die junction temperature -40 125 C TA Ambient temperature -40 105 C 5.4.2 Thermal attributes Board type Symbol Description Single-layer (1s) RJA Four-layer (2s2p) 121 MAPBGA Unit Notes Thermal 65 resistance, junction to ambient (natural convection) C/W 1 RJA Thermal 36 resistance, junction to ambient (natural convection) C/W 1 Single-layer (1s) RJMA Thermal 52 resistance, junction to ambient (200 ft./ min. air speed) C/W 1 Four-layer (2s2p) RJMA Thermal 31 resistance, junction to ambient (200 ft./ min. air speed) C/W 1 -- RJB Thermal 17 resistance, junction to board C/W 2 -- RJC Thermal 13 resistance, junction to case C/W 3 Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 21 Peripheral operating requirements and behaviors Board type Symbol Description -- JT Thermal 3 characterization parameter, junction to package top outside center (natural convection) 1. 2. 3. 4. 121 MAPBGA Unit Notes C/W 4 Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions--Natural Convection (Still Air), or EIA/JEDEC Standard JESD51-6, Integrated Circuit Thermal Test Method Environmental Conditions--Forced Convection (Moving Air). Determined according to JEDEC Standard JESD51-8, Integrated Circuit Thermal Test Method Environmental Conditions--Junction-to-Board. Determined according to Method 1012.1 of MIL-STD 883, Test Method Standard, Microcircuits, with the cold plate temperature used for the case temperature. The value includes the thermal resistance of the interface material between the top of the package and the cold plate. Determined according to JEDEC Standard JESD51-2, Integrated Circuits Thermal Test Method Environmental Conditions--Natural Convection (Still Air). 6 Peripheral operating requirements and behaviors 6.1 Core modules 6.1.1 Debug trace timing specifications Table 12. Debug trace operating behaviors Symbol Description Min. Max. Unit Tcyc Clock period Frequency dependent MHz Twl Low pulse width 2 -- ns Twh High pulse width 2 -- ns Tr Clock and data rise time -- 3 ns Tf Clock and data fall time -- 3 ns Ts Data setup 3 -- ns Th Data hold 2 -- ns Figure 3. TRACE_CLKOUT specifications K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 22 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors TRACE_CLKOUT Ts Th Ts Th TRACE_D[3:0] Figure 4. Trace data specifications 6.1.2 JTAG electricals Table 13. JTAG limited voltage range electricals Symbol J1 Description Min. Max. Unit Operating voltage 2.7 3.6 V TCLK frequency of operation MHz * Boundary Scan 0 10 * JTAG and CJTAG 0 25 * Serial Wire Debug 0 50 1/J1 -- ns * Boundary Scan 50 -- ns * JTAG and CJTAG 20 -- ns * Serial Wire Debug 10 -- ns J4 TCLK rise and fall times -- 3 ns J5 Boundary scan input data setup time to TCLK rise 20 -- ns J6 Boundary scan input data hold time after TCLK rise 0 -- ns J7 TCLK low to boundary scan output data valid -- 25 ns J8 TCLK low to boundary scan output high-Z -- 25 ns J2 TCLK cycle period J3 TCLK clock pulse width J9 TMS, TDI input data setup time to TCLK rise 8 -- ns J10 TMS, TDI input data hold time after TCLK rise 1 -- ns J11 TCLK low to TDO data valid -- 17 ns J12 TCLK low to TDO high-Z -- 17 ns J13 TRST assert time 100 -- ns J14 TRST setup time (negation) to TCLK high 8 -- ns Table 14. JTAG full voltage range electricals Symbol Description Min. Max. Unit Operating voltage 1.71 3.6 V Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 23 Peripheral operating requirements and behaviors Table 14. JTAG full voltage range electricals (continued) Symbol J1 Description Min. Max. TCLK frequency of operation Unit MHz * Boundary Scan 0 10 * JTAG and CJTAG 0 20 * Serial Wire Debug 0 40 1/J1 -- ns * Boundary Scan 50 -- ns * JTAG and CJTAG 25 -- ns * Serial Wire Debug 12.5 -- ns J2 TCLK cycle period J3 TCLK clock pulse width J4 TCLK rise and fall times -- 3 ns J5 Boundary scan input data setup time to TCLK rise 20 -- ns J6 Boundary scan input data hold time after TCLK rise 0 -- ns J7 TCLK low to boundary scan output data valid -- 25 ns J8 TCLK low to boundary scan output high-Z -- 25 ns J9 TMS, TDI input data setup time to TCLK rise 8 -- ns J10 TMS, TDI input data hold time after TCLK rise 1.4 -- ns J11 TCLK low to TDO data valid -- 22.1 ns J12 TCLK low to TDO high-Z -- 22.1 ns J13 TRST assert time 100 -- ns J14 TRST setup time (negation) to TCLK high 8 -- ns J2 J3 J3 TCLK (input) J4 J4 Figure 5. Test clock input timing K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 24 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors TCLK J5 Data inputs J6 Input data valid J7 Data outputs Output data valid J8 Data outputs J7 Data outputs Output data valid Figure 6. Boundary scan (JTAG) timing TCLK J9 TDI/TMS J10 Input data valid J11 TDO Output data valid J12 TDO J11 TDO Output data valid Figure 7. Test Access Port timing K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 25 Peripheral operating requirements and behaviors TCLK J14 J13 TRST Figure 8. TRST timing 6.2 System modules There are no specifications necessary for the device's system modules. 6.3 Clock modules 6.3.1 MCG specifications Table 15. MCG specifications Symbol Description Min. Typ. Max. Unit -- 32.768 -- kHz 31.25 -- 39.0625 kHz fdco_res_t Resolution of trimmed average DCO output frequency at fixed voltage and temperature -- using SCTRIM and SCFTRIM -- 0.3 0.6 %fdco 1 fdco_res_t Resolution of trimmed average DCO output frequency at fixed voltage and temperature -- using SCTRIM only -- 0.2 0.5 %fdco 1 fints_ft Internal reference frequency (slow clock) -- factory trimmed at nominal VDD and 25 C fints_t Internal reference frequency (slow clock) -- user trimmed Notes fdco_t Total deviation of trimmed average DCO output frequency over voltage and temperature -- +0.5/-0.7 3 %fdco 1, fdco_t Total deviation of trimmed average DCO output frequency over fixed voltage and temperature range of 0-70C -- 0.3 3 %fdco 1 fintf_ft Internal reference frequency (fast clock) -- factory trimmed at nominal VDD and 25C -- 4 -- MHz fintf_t Internal reference frequency (fast clock) -- user trimmed at nominal VDD and 25 C 3 -- 5 MHz floc_low Loss of external clock minimum frequency -- RANGE = 00 (3/5) x fints_t -- -- kHz floc_high Loss of external clock minimum frequency -- RANGE = 01, 10, or 11 (16/5) x fints_t -- -- kHz Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 26 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 15. MCG specifications (continued) Symbol Description Min. Typ. Max. Unit 31.25 -- 39.0625 kHz 20 20.97 25 MHz 40 41.94 50 MHz 60 62.91 75 MHz 80 83.89 100 MHz -- 23.99 -- MHz -- 47.97 -- MHz -- 71.99 -- MHz -- 95.98 -- MHz -- 180 -- -- 150 -- -- -- 1 ms 48.0 -- 100 MHz -- 1060 -- A -- 600 -- A 2.0 -- 4.0 MHz Notes FLL ffll_ref fdco FLL reference frequency range DCO output frequency range Low range (DRS=00) 2, 3 640 x ffll_ref Mid range (DRS=01) 1280 x ffll_ref Mid-high range (DRS=10) 1920 x ffll_ref High range (DRS=11) 2560 x ffll_ref fdco_t_DMX32 DCO output frequency Low range (DRS=00) 4, 5 732 x ffll_ref Mid range (DRS=01) 1464 x ffll_ref Mid-high range (DRS=10) 2197 x ffll_ref High range (DRS=11) 2929 x ffll_ref Jcyc_fll FLL period jitter * fDCO = 48 MHz * fDCO = 98 MHz tfll_acquire FLL target frequency acquisition time ps 6 PLL fvco VCO operating frequency Ipll PLL operating current * PLL @ 96 MHz (fosc_hi_1 = 8 MHz, fpll_ref = 2 MHz, VDIV multiplier = 48) Ipll PLL operating current * PLL @ 48 MHz (fosc_hi_1 = 8 MHz, fpll_ref = 2 MHz, VDIV multiplier = 24) fpll_ref PLL reference frequency range Jcyc_pll PLL period jitter (RMS) Jacc_pll 7 7 8 * fvco = 48 MHz -- 120 -- ps * fvco = 100 MHz -- 50 -- ps PLL accumulated jitter over 1s (RMS) 8 * fvco = 48 MHz -- 1350 -- ps * fvco = 100 MHz -- 600 -- ps Dlock Lock entry frequency tolerance 1.49 -- 2.98 % Dunl Lock exit frequency tolerance 4.47 -- 5.97 % Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 27 Peripheral operating requirements and behaviors Table 15. MCG specifications (continued) Symbol tpll_lock Description Lock detector detection time Min. Typ. Max. Unit Notes -- -- 150 x 10-6 + 1075(1/ fpll_ref) s 9 1. This parameter is measured with the internal reference (slow clock) being used as a reference to the FLL (FEI clock mode). 2. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=0. 3. The resulting system clock frequencies should not exceed their maximum specified values. The DCO frequency deviation (fdco_t) over voltage and temperature should be considered. 4. These typical values listed are with the slow internal reference clock (FEI) using factory trim and DMX32=1. 5. The resulting clock frequency must not exceed the maximum specified clock frequency of the device. 6. This specification applies to any time the FLL reference source or reference divider is changed, trim value is changed, DMX32 bit is changed, DRS bits are changed, or changing from FLL disabled (BLPE, BLPI) to FLL enabled (FEI, FEE, FBE, FBI). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 7. Excludes any oscillator currents that are also consuming power while PLL is in operation. 8. This specification was obtained using a Freescale developed PCB. PLL jitter is dependent on the noise characteristics of each PCB and results will vary. 9. This specification applies to any time the PLL VCO divider or reference divider is changed, or changing from PLL disabled (BLPE, BLPI) to PLL enabled (PBE, PEE). If a crystal/resonator is being used as the reference, this specification assumes it is already running. 6.3.2 Oscillator electrical specifications This section provides the electrical characteristics of the module. 6.3.2.1 Oscillator DC electrical specifications Table 16. Oscillator DC electrical specifications Symbol Description Min. Typ. Max. Unit VDD Supply voltage 1.71 -- 3.6 V IDDOSC Supply current -- low-power mode (HGO=0) Notes 1 * 32 kHz -- 500 -- nA * 4 MHz -- 200 -- A * 8 MHz (RANGE=01) -- 300 -- A * 16 MHz -- 950 -- A * 24 MHz -- 1.2 -- mA * 32 MHz -- 1.5 -- mA Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 28 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 16. Oscillator DC electrical specifications (continued) Symbol Description Min. IDDOSC Supply current -- high gain mode (HGO=1) Typ. Max. Unit Notes 1 * 32 kHz -- 25 -- A * 4 MHz -- 400 -- A * 8 MHz (RANGE=01) -- 500 -- A * 16 MHz -- 2.5 -- mA * 24 MHz -- 3 -- mA * 32 MHz -- 4 -- mA Cx EXTAL load capacitance -- -- -- 2, 3 Cy XTAL load capacitance -- -- -- 2, 3 RF Feedback resistor -- low-frequency, low-power mode (HGO=0) -- -- -- M Feedback resistor -- low-frequency, high-gain mode (HGO=1) -- 10 -- M Feedback resistor -- high-frequency, low-power mode (HGO=0) -- -- -- M Feedback resistor -- high-frequency, high-gain mode (HGO=1) -- 1 -- M Series resistor -- low-frequency, low-power mode (HGO=0) -- -- -- k Series resistor -- low-frequency, high-gain mode (HGO=1) -- 200 -- k Series resistor -- high-frequency, low-power mode (HGO=0) -- -- -- k RS 2, 4 Series resistor -- high-frequency, high-gain mode (HGO=1) Vpp5 1. 2. 3. 4. 5. -- 0 -- k Peak-to-peak amplitude of oscillation (oscillator mode) -- low-frequency, low-power mode (HGO=0) -- 0.6 -- V Peak-to-peak amplitude of oscillation (oscillator mode) -- low-frequency, high-gain mode (HGO=1) -- VDD -- V Peak-to-peak amplitude of oscillation (oscillator mode) -- high-frequency, low-power mode (HGO=0) -- 0.6 -- V Peak-to-peak amplitude of oscillation (oscillator mode) -- high-frequency, high-gain mode (HGO=1) -- VDD -- V VDD=3.3 V, Temperature =25 C See crystal or resonator manufacturer's recommendation Cx,Cy can be provided by using either the integrated capacitors or by using external components. When low power mode is selected, RF is integrated and must not be attached externally. The EXTAL and XTAL pins should only be connected to required oscillator components and must not be connected to any other devices. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 29 Peripheral operating requirements and behaviors 6.3.2.2 Symbol Oscillator frequency specifications Table 17. Oscillator frequency specifications Description Min. Typ. Max. Unit fosc_lo Oscillator crystal or resonator frequency -- low frequency mode (MCG_C2[RANGE]=00) 32 -- 40 kHz fosc_hi_1 Oscillator crystal or resonator frequency -- high frequency mode (low range) (MCG_C2[RANGE]=01) 3 -- 8 MHz fosc_hi_2 Oscillator crystal or resonator frequency -- high frequency mode (high range) (MCG_C2[RANGE]=1x) 8 -- 32 MHz fec_extal Input clock frequency (external clock mode) -- -- 50 MHz tdc_extal Input clock duty cycle (external clock mode) 40 50 60 % Crystal startup time -- 32 kHz low-frequency, low-power mode (HGO=0) -- 750 -- ms Crystal startup time -- 32 kHz low-frequency, high-gain mode (HGO=1) -- 250 -- ms Crystal startup time -- 8 MHz high-frequency (MCG_C2[RANGE]=01), low-power mode (HGO=0) -- 0.6 -- ms Crystal startup time -- 8 MHz high-frequency (MCG_C2[RANGE]=01), high-gain mode (HGO=1) -- 1 -- ms tcst Notes 1, 2 3, 4 1. Other frequency limits may apply when external clock is being used as a reference for the FLL or PLL. 2. When transitioning from FBE to FEI mode, restrict the frequency of the input clock so that, when it is divided by FRDIV, it remains within the limits of the DCO input clock frequency. 3. Proper PC board layout procedures must be followed to achieve specifications. 4. Crystal startup time is defined as the time between the oscillator being enabled and the OSCINIT bit in the MCG_S register being set. NOTE The 32 kHz oscillator works in low power mode by default and cannot be moved into high power/gain mode. 6.3.3 32 kHz oscillator electrical characteristics This section describes the module electrical characteristics. 6.3.3.1 32 kHz oscillator DC electrical specifications Table 18. 32kHz oscillator DC electrical specifications Symbol Description Min. Typ. Max. Unit VBAT Supply voltage 1.71 -- 3.6 V -- 100 -- M RF Internal feedback resistor Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 30 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 18. 32kHz oscillator DC electrical specifications (continued) Symbol Description Min. Typ. Max. Unit Cpara Parasitical capacitance of EXTAL32 and XTAL32 -- 5 7 pF Vpp1 Peak-to-peak amplitude of oscillation -- 0.6 -- V 1. When a crystal is being used with the 32 kHz oscillator, the EXTAL32 and XTAL32 pins should only be connected to required oscillator components and must not be connected to any other devices. 6.3.3.2 Symbol fosc_lo tstart fec_extal32 32 kHz oscillator frequency specifications Table 19. 32 kHz oscillator frequency specifications Description Min. Typ. Max. Unit Oscillator crystal -- 32.768 -- kHz Crystal start-up time -- 1000 -- ms 1 Externally provided input clock frequency -- 32.768 -- kHz 2 700 -- VBAT mV 2, 3 vec_extal32 Externally provided input clock amplitude Notes 1. Proper PC board layout procedures must be followed to achieve specifications. 2. This specification is for an externally supplied clock driven to EXTAL32 and does not apply to any other clock input. The oscillator remains enabled and XTAL32 must be left unconnected. 3. The parameter specified is a peak-to-peak value and VIH and VIL specifications do not apply. The voltage of the applied clock must be within the range of VSS to VBAT. 6.4 Memories and memory interfaces 6.4.1 Flash electrical specifications This section describes the electrical characteristics of the flash memory module. 6.4.1.1 Flash timing specifications -- program and erase The following specifications represent the amount of time the internal charge pumps are active and do not include command overhead. Table 20. NVM program/erase timing specifications Symbol Description Min. Typ. thvpgm4 thversscr Longword Program high-voltage time -- 7.5 18 s Sector Erase high-voltage time -- 13 113 ms 1 -- 104 904 ms 1 thversblk256k Erase Block high-voltage time for 256 KB Max. Unit Notes 1. Maximum time based on expectations at cycling end-of-life. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 31 Peripheral operating requirements and behaviors 6.4.1.2 Symbol Flash timing specifications -- commands Table 21. Flash command timing specifications Description Min. Typ. Max. Unit -- -- 1.7 ms Notes Read 1s Block execution time trd1blk256k * 256 KB program/data flash trd1sec2k Read 1s Section execution time (flash sector) -- -- 60 s 1 tpgmchk Program Check execution time -- -- 45 s 1 trdrsrc Read Resource execution time -- -- 30 s 1 tpgm4 Program Longword execution time -- 65 145 s Erase Flash Block execution time tersblk256k tersscr * 256 KB program/data flash Erase Flash Sector execution time 2 -- 122 985 ms -- 14 114 ms 2 Program Section execution time tpgmsec512 * 512 bytes flash -- 2.4 -- ms tpgmsec1k * 1 KB flash -- 4.7 -- ms tpgmsec2k * 2 KB flash -- 9.3 -- ms trd1all Read 1s All Blocks execution time -- -- 1.8 ms trdonce Read Once execution time -- -- 25 s tpgmonce 1 Program Once execution time -- 65 -- s tersall Erase All Blocks execution time -- 250 2000 ms 2 tvfykey Verify Backdoor Access Key execution time -- -- 30 s 1 Swap Control execution time tswapx01 * control code 0x01 -- 200 -- s tswapx02 * control code 0x02 -- 70 150 s tswapx04 * control code 0x04 -- 70 150 s tswapx08 * control code 0x08 -- -- 30 s 1. Assumes 25 MHz flash clock frequency. 2. Maximum times for erase parameters based on expectations at cycling end-of-life. 6.4.1.3 Flash high voltage current behaviors Table 22. Flash high voltage current behaviors Symbol Description Min. Typ. Max. Unit IDD_PGM Average current adder during high voltage flash programming operation -- 2.5 6.0 mA IDD_ERS Average current adder during high voltage flash erase operation -- 1.5 4.0 mA K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 32 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.4.1.4 Symbol Reliability specifications Table 23. NVM reliability specifications Description Min. Typ.1 Max. Unit Notes Program Flash tnvmretp10k Data retention after up to 10 K cycles 5 50 -- years tnvmretp1k Data retention after up to 1 K cycles 20 100 -- years nnvmcycp Cycling endurance 10 K 50 K -- cycles 2 1. Typical data retention values are based on measured response accelerated at high temperature and derated to a constant 25C use profile. Engineering Bulletin EB618 does not apply to this technology. Typical endurance defined in Engineering Bulletin EB619. 2. Cycling endurance represents number of program/erase cycles at -40C Tj 125C. 6.4.2 EzPort switching specifications Table 24. EzPort switching specifications Num Description Min. Max. Unit Operating voltage 1.71 3.6 V EP1 EZP_CK frequency of operation (all commands except READ) -- fSYS/2 MHz EP1a EZP_CK frequency of operation (READ command) -- fSYS/8 MHz EP2 EZP_CS negation to next EZP_CS assertion 2 x tEZP_CK -- ns EP3 EZP_CS input valid to EZP_CK high (setup) 5 -- ns EP4 EZP_CK high to EZP_CS input invalid (hold) 5 -- ns EP5 EZP_D input valid to EZP_CK high (setup) 2 -- ns EP6 EZP_CK high to EZP_D input invalid (hold) 5 -- ns EP7 EZP_CK low to EZP_Q output valid -- 16 ns EP8 EZP_CK low to EZP_Q output invalid (hold) 0 -- ns EP9 EZP_CS negation to EZP_Q tri-state -- 12 ns K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 33 Peripheral operating requirements and behaviors EZP_CK EP2 EP4 EP3 EZP_CS EP9 EP7 EP8 EZP_Q (output) EP5 EP6 EZP_D (input) Figure 9. EzPort Timing Diagram 6.4.3 Flexbus switching specifications All processor bus timings are synchronous; input setup/hold and output delay are given in respect to the rising edge of a reference clock, FB_CLK. The FB_CLK frequency may be the same as the internal system bus frequency or an integer divider of that frequency. The following timing numbers indicate when data is latched or driven onto the external bus, relative to the Flexbus output clock (FB_CLK). All other timing relationships can be derived from these values. Table 25. Flexbus limited voltage range switching specifications Num Description Min. Max. Unit Notes Operating voltage 2.7 3.6 V Frequency of operation -- FB_CLK MHz FB1 Clock period 20 -- ns FB2 Address, data, and control output valid -- 11.5 ns 1 FB3 Address, data, and control output hold 0.5 -- ns 1 FB4 Data and FB_TA input setup 8.5 -- ns 2 FB5 Data and FB_TA input hold 0.5 -- ns 2 1. Specification is valid for all FB_AD[31:0], FB_BE/BWEn, FB_CSn, FB_OE, FB_R/W,FB_TBST, FB_TSIZ[1:0], FB_ALE, and FB_TS. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 34 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 2. Specification is valid for all FB_AD[31:0] and FB_TA. Table 26. Flexbus full voltage range switching specifications Num Description Min. Max. Unit Operating voltage 1.71 3.6 V Frequency of operation Notes -- FB_CLK MHz 1/FB_CLK -- ns Address, data, and control output valid -- 13.5 ns 1 FB3 Address, data, and control output hold 0 -- ns 1 FB4 Data and FB_TA input setup 13.7 -- ns 2 FB5 Data and FB_TA input hold 0.5 -- ns 2 FB1 Clock period FB2 1. Specification is valid for all FB_AD[31:0], FB_BE/BWEn, FB_CSn, FB_OE, FB_R/W,FB_TBST, FB_TSIZ[1:0], FB_ALE, and FB_TS. 2. Specification is valid for all FB_AD[31:0] and FB_TA. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 35 Peripheral operating requirements and behaviors FB1 FB_CLK FB3 FB5 FB_A[Y] Address FB2 FB_D[X] FB4 Address Data FB_RW FB_TS FB_ALE AA=1 FB_CSn AA=0 FB_OEn FB4 FB_BEn FB5 AA=1 FB_TA FB_TSIZ[1:0] AA=0 TSIZ Figure 10. FlexBus read timing diagram K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 36 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors FB1 FB_CLK FB2 FB3 FB_A[Y] FB_D[X] Address Address Data FB_RW FB_TS FB_ALE AA=1 FB_CSn AA=0 FB_OEn FB4 FB_BEn FB5 AA=1 FB_TA FB_TSIZ[1:0] AA=0 TSIZ Figure 11. FlexBus write timing diagram 6.5 Security and integrity modules There are no specifications necessary for the device's security and integrity modules. 6.6 Analog K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 37 Peripheral operating requirements and behaviors 6.6.1 ADC electrical specifications The 16-bit accuracy specifications listed in Table 27 and Table 28 are achievable on the differential pins ADCx_DP0, ADCx_DM0, ADCx_DP1, ADCx_DM1, ADCx_DP3, and ADCx_DM3. The ADCx_DP2 and ADCx_DM2 ADC inputs are connected to the PGA outputs and are not direct device pins. Accuracy specifications for these pins are defined in Table 29 and Table 30. All other ADC channels meet the 13-bit differential/12-bit single-ended accuracy specifications. 6.6.1.1 16-bit ADC operating conditions Table 27. 16-bit ADC operating conditions Symbol Description Conditions Min. Typ.1 Max. Unit VDDA Supply voltage Absolute 1.71 -- 3.6 V VDDA Supply voltage Delta to VDD (VDD - VDDA) -100 0 +100 mV 2 VSSA Ground voltage Delta to VSS (VSS - VSSA) -100 0 +100 mV 2 VREFH ADC reference voltage high 1.13 VDDA VDDA V VREFL ADC reference voltage low VSSA VSSA VSSA V VADIN Input voltage * 16-bit differential mode VREFL -- 31/32 * VREFH V * All other modes VREFL -- * 16-bit mode -- 8 10 * 8-bit / 10-bit / 12-bit modes -- 4 5 -- 2 5 CADIN RADIN RAS Input capacitance Input resistance Notes VREFH pF k Analog source resistance 13-bit / 12-bit modes fADCK < 4 MHz -- -- 5 k fADCK ADC conversion clock frequency 13-bit mode 1.0 -- 18.0 MHz 4 fADCK ADC conversion clock frequency 16-bit mode 2.0 -- 12.0 MHz 4 Crate ADC conversion rate 13-bit modes No ADC hardware averaging 3 5 20.000 -- 818.330 Ksps Continuous conversions enabled, subsequent conversion time Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 38 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 27. 16-bit ADC operating conditions (continued) Symbol Crate Description Conditions ADC conversion rate 16-bit mode Min. Typ.1 Max. Unit Notes 5 No ADC hardware averaging 37.037 -- 461.467 Ksps Continuous conversions enabled, subsequent conversion time 1. Typical values assume VDDA = 3.0 V, Temp = 25 C, fADCK = 1.0 MHz, unless otherwise stated. Typical values are for reference only, and are not tested in production. 2. DC potential difference. 3. This resistance is external to MCU. To achieve the best results, the analog source resistance must be kept as low as possible. The results in this data sheet were derived from a system that had < 8 analog source resistance. The RAS/CAS time constant should be kept to < 1 ns. 4. To use the maximum ADC conversion clock frequency, CFG2[ADHSC] must be set and CFG1[ADLPC] must be clear. 5. For guidelines and examples of conversion rate calculation, download the ADC calculator tool. SIMPLIFIED INPUT PIN EQUIVALENT CIRCUIT Z ADIN SIMPLIFIED CHANNEL SELECT CIRCUIT Pad leakage due to input protection Z AS R AS ADC SAR ENGINE R ADIN V ADIN C AS V AS R ADIN INPUT PIN R ADIN INPUT PIN R ADIN INPUT PIN C ADIN Figure 12. ADC input impedance equivalency diagram 6.6.1.2 16-bit ADC electrical characteristics Table 28. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) Symbol Description IDDA_ADC Supply current Conditions1. Min. Typ.2 Max. Unit Notes 0.215 -- 1.7 mA 3 Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 39 Peripheral operating requirements and behaviors Table 28. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued) Symbol fADACK Description ADC asynchronous clock source Sample Time TUE DNL INL EFS Conditions1. Min. Typ.2 Max. Unit Notes * ADLPC = 1, ADHSC = 0 1.2 2.4 3.9 MHz * ADLPC = 1, ADHSC = 1 2.4 4.0 6.1 MHz tADACK = 1/ fADACK * ADLPC = 0, ADHSC = 0 3.0 5.2 7.3 MHz * ADLPC = 0, ADHSC = 1 4.4 6.2 9.5 MHz LSB4 5 LSB4 5 LSB4 5 LSB4 VADIN = VDDA See Reference Manual chapter for sample times Total unadjusted error * 12-bit modes -- 4 6.8 * <12-bit modes -- 1.4 2.1 Differential nonlinearity * 12-bit modes -- 0.7 -1.1 to +1.9 Integral nonlinearity Full-scale error -0.3 to 0.5 * <12-bit modes -- 0.2 * 12-bit modes -- 1.0 -2.7 to +1.9 -0.7 to +0.5 * <12-bit modes -- 0.5 * 12-bit modes -- -4 -5.4 * <12-bit modes -- -1.4 -1.8 5 EQ ENOB Quantization error * 16-bit modes -- -1 to 0 -- * 13-bit modes -- -- 0.5 Effective number 16-bit differential mode of bits * Avg = 32 * Avg = 4 LSB4 6 12.8 14.5 -- bits 11.9 13.8 -- bits 12.2 13.9 -- bits 11.4 13.1 -- bits 16-bit single-ended mode * Avg = 32 * Avg = 4 SINAD THD Signal-to-noise plus distortion See ENOB Total harmonic distortion 16-bit differential mode 6.02 x ENOB + 1.76 * Avg = 32 16-bit single-ended mode * Avg = 32 SFDR Spurious free dynamic range dB 7 -- -94 -- dB -- -85 -- dB 16-bit differential mode * Avg = 32 16-bit single-ended mode * Avg = 32 7 82 95 -- dB 78 90 -- dB Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 40 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 28. 16-bit ADC characteristics (VREFH = VDDA, VREFL = VSSA) (continued) Symbol Description EIL Input leakage error Conditions1. Min. Typ.2 Max. IIn x RAS Unit Notes mV IIn = leakage current (refer to the MCU's voltage and current operating ratings) VTEMP25 Temp sensor slope Across the full temperature range of the device 1.55 1.62 1.69 mV/C Temp sensor voltage 25 C 706 716 726 mV 1. All accuracy numbers assume the ADC is calibrated with VREFH = VDDA 2. Typical values assume VDDA = 3.0 V, Temp = 25 C, fADCK = 2.0 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 3. The ADC supply current depends on the ADC conversion clock speed, conversion rate and ADC_CFG1[ADLPC] (low power). For lowest power operation, ADC_CFG1[ADLPC] must be set, the ADC_CFG2[ADHSC] bit must be clear with 1 MHz ADC conversion clock speed. 4. 1 LSB = (VREFH - VREFL)/2N 5. ADC conversion clock < 16 MHz, Max hardware averaging (AVGE = %1, AVGS = %11) 6. Input data is 100 Hz sine wave. ADC conversion clock < 12 MHz. 7. Input data is 1 kHz sine wave. ADC conversion clock < 12 MHz. Figure 13. Typical ENOB vs. ADC_CLK for 16-bit differential mode K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 41 Peripheral operating requirements and behaviors Figure 14. Typical ENOB vs. ADC_CLK for 16-bit single-ended mode 6.6.1.3 16-bit ADC with PGA operating conditions Table 29. 16-bit ADC with PGA operating conditions Symbol Description Conditions Min. Typ.1 Max. Unit VDDA Supply voltage Absolute 1.71 -- 3.6 V VREFPGA PGA ref voltage VADIN VCM RPGAD VREF_OU VREF_OU VREF_OU T T T V Notes 2, 3 Input voltage VSSA -- VDDA V Input Common Mode range VSSA -- VDDA V Gain = 1, 2, 4, 8 -- 128 -- k IN+ to IN-4 Gain = 16, 32 -- 64 -- Gain = 64 -- 32 -- Differential input impedance RAS Analog source resistance -- 100 -- 5 TS ADC sampling time 1.25 -- -- s 6 Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 42 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 29. 16-bit ADC with PGA operating conditions (continued) Symbol Crate Description Conditions ADC conversion rate 13 bit modes Min. Typ.1 Max. Unit Notes 18.484 -- 450 Ksps 7 37.037 -- 250 Ksps 8 No ADC hardware averaging Continuous conversions enabled Peripheral clock = 50 MHz 16 bit modes No ADC hardware averaging Continuous conversions enabled Peripheral clock = 50 MHz 1. Typical values assume VDDA = 3.0 V, Temp = 25C, fADCK = 6 MHz unless otherwise stated. Typical values are for reference only and are not tested in production. 2. ADC must be configured to use the internal voltage reference (VREF_OUT) 3. PGA reference is internally connected to the VREF_OUT pin. If the user wishes to drive VREF_OUT with a voltage other than the output of the VREF module, the VREF module must be disabled. 4. For single ended configurations the input impedance of the driven input is RPGAD/2 5. The analog source resistance (RAS), external to MCU, should be kept as minimum as possible. Increased RAS causes drop in PGA gain without affecting other performances. This is not dependent on ADC clock frequency. 6. The minimum sampling time is dependent on input signal frequency and ADC mode of operation. A minimum of 1.25s time should be allowed for Fin=4 kHz at 16-bit differential mode. Recommended ADC setting is: ADLSMP=1, ADLSTS=2 at 8 MHz ADC clock. 7. ADC clock = 18 MHz, ADLSMP = 1, ADLST = 00, ADHSC = 1 8. ADC clock = 12 MHz, ADLSMP = 1, ADLST = 01, ADHSC = 1 6.6.1.4 16-bit ADC with PGA characteristics with Chop enabled (ADC_PGA[PGACHPb] =0) Table 30. 16-bit ADC with PGA characteristics Symbol Description Conditions IDDA_PGA Supply current Low power (ADC_PGA[PGALPb]=0) IDC_PGA Input DC current Min. Typ.1 Max. Unit Notes -- 420 644 A 2 A 3 Gain =1, VREFPGA=1.2V, VCM=0.5V -- 1.54 -- A Gain =64, VREFPGA=1.2V, VCM=0.1V -- 0.57 -- A Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 43 Peripheral operating requirements and behaviors Table 30. 16-bit ADC with PGA characteristics (continued) Symbol G BW Description Gain4 Input signal bandwidth PSRR Power supply rejection ratio CMRR Common mode rejection ratio Min. Typ.1 Max. * PGAG=0 0.95 1 1.05 * PGAG=1 1.9 2 2.1 * PGAG=2 3.8 4 4.2 * PGAG=3 7.6 8 8.4 * PGAG=4 15.2 16 16.6 * PGAG=5 30.0 31.6 33.2 * PGAG=6 58.8 63.3 67.8 -- -- 4 kHz -- -- 40 kHz -- -84 -- dB VDDA= 3V 100mV, fVDDA= 50Hz, 60Hz * Gain=1 -- -84 -- dB * Gain=64 -- -85 -- dB VCM= 500mVpp, fVCM= 50Hz, 100Hz Conditions * 16-bit modes * < 16-bit modes Gain=1 Unit Notes RAS < 100 VOFS Input offset voltage -- 0.2 -- mV Output offset = VOFS*(Gain+1) TGSW Gain switching settling time -- -- 10 s 5 dG/dT Gain drift over full temperature range * Gain=1 * Gain=64 -- 6 10 ppm/C -- 31 42 ppm/C * Gain=1 * Gain=64 -- 0.07 0.21 %/V -- 0.14 0.31 %/V dG/dVDDA Gain drift over supply voltage EIL Input leakage error All modes IIn x RAS mV VDDA from 1.71 to 3.6V IIn = leakage current (refer to the MCU's voltage and current operating ratings) VPP,DIFF SNR THD Maximum differential input signal swing V 6 16-bit differential mode, Average=32 where VX = VREFPGA x 0.583 Signal-to-noise ratio * Gain=1 80 90 -- dB * Gain=64 52 66 -- dB Total harmonic distortion * Gain=1 85 100 -- dB * Gain=64 49 95 -- dB 16-bit differential mode, Average=32, fin=100Hz Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 44 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 30. 16-bit ADC with PGA characteristics (continued) Symbol Description SFDR Spurious free dynamic range Effective number of bits ENOB SINAD Signal-to-noise plus distortion ratio Min. Typ.1 Max. Unit Notes * Gain=1 85 105 -- dB * Gain=64 53 88 -- dB 16-bit differential mode, Average=32, fin=100Hz * Gain=1, Average=4 11.6 13.4 -- bits * Gain=1, Average=8 8.0 13.6 -- bits * Gain=64, Average=4 7.2 9.6 -- bits * Gain=64, Average=8 6.3 9.6 -- bits * Gain=1, Average=32 12.8 14.5 -- bits * Gain=2, Average=32 11.0 14.3 -- bits * Gain=4, Average=32 7.9 13.8 -- bits * Gain=8, Average=32 7.3 13.1 -- bits * Gain=16, Average=32 6.8 12.5 -- bits * Gain=32, Average=32 6.8 11.5 -- bits * Gain=64, Average=32 7.5 10.6 -- bits Conditions See ENOB 6.02 x ENOB + 1.76 16-bit differential mode,fin=100Hz dB 1. Typical values assume VDDA =3.0V, Temp=25C, fADCK=6MHz unless otherwise stated. 2. This current is a PGA module adder, in addition to ADC conversion currents. 3. Between IN+ and IN-. The PGA draws a DC current from the input terminals. The magnitude of the DC current is a strong function of input common mode voltage (VCM) and the PGA gain. 4. Gain = 2PGAG 5. After changing the PGA gain setting, a minimum of 2 ADC+PGA conversions should be ignored. 6. Limit the input signal swing so that the PGA does not saturate during operation. Input signal swing is dependent on the PGA reference voltage and gain setting. 6.6.2 CMP and 6-bit DAC electrical specifications Table 31. Comparator and 6-bit DAC electrical specifications Symbol Description Min. Typ. Max. Unit VDD Supply voltage 1.71 -- 3.6 V IDDHS Supply current, High-speed mode (EN=1, PMODE=1) -- -- 200 A IDDLS Supply current, low-speed mode (EN=1, PMODE=0) -- -- 20 A VAIN Analog input voltage VSS - 0.3 -- VDD V VAIO Analog input offset voltage -- -- 20 mV Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 45 Peripheral operating requirements and behaviors Table 31. Comparator and 6-bit DAC electrical specifications (continued) Symbol VH Description Min. Typ. Max. Unit * CR0[HYSTCTR] = 00 -- 5 -- mV * CR0[HYSTCTR] = 01 -- 10 -- mV * CR0[HYSTCTR] = 10 -- 20 -- mV * CR0[HYSTCTR] = 11 -- 30 -- mV Analog comparator hysteresis1 VCMPOh Output high VDD - 0.5 -- -- V VCMPOl Output low -- -- 0.5 V tDHS Propagation delay, high-speed mode (EN=1, PMODE=1) 20 50 200 ns tDLS Propagation delay, low-speed mode (EN=1, PMODE=0) 80 250 600 ns Analog comparator initialization delay2 -- -- 40 s 6-bit DAC current adder (enabled) -- 7 -- A IDAC6b INL 6-bit DAC integral non-linearity -0.5 -- 0.5 LSB3 DNL 6-bit DAC differential non-linearity -0.3 -- 0.3 LSB 1. Typical hysteresis is measured with input voltage range limited to 0.6 to VDD-0.6 V. 2. Comparator initialization delay is defined as the time between software writes to change control inputs (Writes to DACEN, VRSEL, PSEL, MSEL, VOSEL) and the comparator output settling to a stable level. 3. 1 LSB = Vreference/64 K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 46 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 0.08 0.07 0.06 HYSTCTR Setting CM P Hystereris (V) 0.05 00 0.04 01 10 11 0.03 0.02 0.01 0 0.1 0.4 0.7 1 1.3 1.6 1.9 Vin level (V) 2.2 2.5 2.8 3.1 Figure 15. Typical hysteresis vs. Vin level (VDD=3.3V, PMODE=0) K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 47 Peripheral operating requirements and behaviors 0.18 0.16 0.14 CMP P Hystereris (V) 0.12 HYSTCTR Setting 0.1 00 01 0.08 0 08 10 11 0.06 0.04 0.02 0 0.1 0.4 0.7 1 1.3 1.6 Vin level (V) 1.9 2.2 2.5 2.8 3.1 Figure 16. Typical hysteresis vs. Vin level (VDD=3.3V, PMODE=1) 6.6.3 12-bit DAC electrical characteristics 6.6.3.1 Symbol 12-bit DAC operating requirements Table 32. 12-bit DAC operating requirements Desciption Min. Max. Unit VDDA Supply voltage 1.71 3.6 V VDACR Reference voltage 1.13 3.6 V TA Temperature Operating temperature range of the device CL Output load capacitance -- 100 pF IL Output load current -- 1 mA Notes 1 C 2 1. The DAC reference can be selected to be VDDA or the voltage output of the VREF module (VREF_OUT) 2. A small load capacitance (47 pF) can improve the bandwidth performance of the DAC K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 48 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.6.3.2 Symbol 12-bit DAC operating behaviors Table 33. 12-bit DAC operating behaviors Description IDDA_DACL Supply current -- low-power mode Min. Typ. Max. Unit -- -- 330 A -- -- 1200 A Notes P IDDA_DACH Supply current -- high-speed mode P tDACLP Full-scale settling time (0x080 to 0xF7F) -- low-power mode -- 100 200 s 1 tDACHP Full-scale settling time (0x080 to 0xF7F) -- high-power mode -- 15 30 s 1 -- 0.7 1 s 1 -- -- 100 mV tCCDACLP Code-to-code settling time (0xBF8 to 0xC08) -- low-power mode and high-speed mode Vdacoutl DAC output voltage range low -- high-speed mode, no load, DAC set to 0x000 Vdacouth DAC output voltage range high -- highspeed mode, no load, DAC set to 0xFFF VDACR -100 -- VDACR mV INL Integral non-linearity error -- high speed mode -- -- 8 LSB 2 DNL Differential non-linearity error -- VDACR > 2 V -- -- 1 LSB 3 DNL Differential non-linearity error -- VDACR = VREF_OUT -- -- 1 LSB 4 -- 0.4 0.8 %FSR 5 Gain error -- 0.1 0.6 %FSR 5 Power supply rejection ratio, VDDA > = 2.4 V 60 -- 90 dB TCO Temperature coefficient offset voltage -- 3.7 -- V/C TGE Temperature coefficient gain error -- 0.000421 -- %FSR/C Rop Output resistance load = 3 k -- -- 250 SR Slew rate -80h F7Fh 80h VOFFSET Offset error EG PSRR 1. 2. 3. 4. 5. 6. V/s * High power (SPHP) 1.2 1.7 -- * Low power (SPLP) 0.05 0.12 -- -- -- -80 CT Channel to channel cross talk BW 3dB bandwidth 6 dB kHz * High power (SPHP) 550 -- -- * Low power (SPLP) 40 -- -- Settling within 1 LSB The INL is measured for 0+100mV to VDACR-100 mV The DNL is measured for 0+100 mV to VDACR-100 mV The DNL is measured for 0+100mV to VDACR-100 mV with VDDA > 2.4V Calculated by a best fit curve from VSS+100 mV to VDACR-100 mV VDDA = 3.0V, reference select set for VDDA (DACx_CO:DACRFS = 1), high power mode(DACx_C0:LPEN = 0), DAC set to 0x800, Temp range from -40C to 105C K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 49 Peripheral operating requirements and behaviors Figure 17. Typical INL error vs. digital code K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 50 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Figure 18. Offset at half scale vs. temperature 6.6.4 Voltage reference electrical specifications Table 34. VREF full-range operating requirements Symbol Description Min. Max. Unit VDDA Supply voltage 1.71 3.6 V TA Temperature CL Output load capacitance Operating temperature range of the device C 100 nF Notes 1, 2 1. CL must be connected to VREF_OUT if the VREF_OUT functionality is being used for either an internal or external reference. 2. The load capacitance should not exceed +/-25% of the nominal specified CL value over the operating temperature range of the device. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 51 Peripheral operating requirements and behaviors Table 35. VREF full-range operating behaviors Symbol Description Min. Typ. Max. Unit Notes Vout Voltage reference output with factory trim at nominal VDDA and temperature=25C 1.1915 1.195 1.1977 V Vout Voltage reference output -- factory trim 1.1584 -- 1.2376 V Vout Voltage reference output -- user trim 1.193 -- 1.197 V Vstep Voltage reference trim step -- 0.5 -- mV Vtdrift Temperature drift (Vmax -Vmin across the full temperature range) -- -- 80 mV Ibg Bandgap only current -- -- 80 A 1 Ilp Low-power buffer current -- -- 360 uA 1 Ihp High-power buffer current -- -- 1 mA 1 V 1, 2 VLOAD Load regulation * current = 1.0 mA -- 200 -- Tstup Buffer startup time -- -- 100 s Vvdrift Voltage drift (Vmax -Vmin across the full voltage range) -- 2 -- mV 1 1. See the chip's Reference Manual for the appropriate settings of the VREF Status and Control register. 2. Load regulation voltage is the difference between the VREF_OUT voltage with no load vs. voltage with defined load Table 36. VREF limited-range operating requirements Symbol Description Min. Max. Unit TA Temperature 0 50 C Notes Table 37. VREF limited-range operating behaviors Symbol Vout Description Voltage reference output with factory trim Min. Max. Unit 1.173 1.225 V Notes 6.7 Timers See General switching specifications. 6.8 Communication interfaces K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 52 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6.8.1 CAN switching specifications See General switching specifications. 6.8.2 DSPI switching specifications (limited voltage range) The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with master and slave operations. Many of the transfer attributes are programmable. The tables below provide DSPI timing characteristics for classic SPI timing modes. Refer to the DSPI chapter of the Reference Manual for information on the modified transfer formats used for communicating with slower peripheral devices. Table 38. Master mode DSPI timing (limited voltage range) Num Description Min. Max. Unit Operating voltage 2.7 3.6 V Frequency of operation -- 25 MHz Notes DS1 DSPI_SCK output cycle time 2 x tBUS -- ns DS2 DSPI_SCK output high/low time (tSCK/2) - 2 (tSCK/2) + 2 ns DS3 DSPI_PCSn valid to DSPI_SCK delay (tBUS x 2) - 2 -- ns 1 DS4 DSPI_SCK to DSPI_PCSn invalid delay (tBUS x 2) - 2 -- ns 2 DS5 DSPI_SCK to DSPI_SOUT valid -- 8 ns DS6 DSPI_SCK to DSPI_SOUT invalid 0 -- ns DS7 DSPI_SIN to DSPI_SCK input setup 14 -- ns DS8 DSPI_SCK to DSPI_SIN input hold 0 -- ns 1. The delay is programmable in SPIx_CTARn[PSSCK] and SPIx_CTARn[CSSCK]. 2. The delay is programmable in SPIx_CTARn[PASC] and SPIx_CTARn[ASC]. DSPI_PCSn DS3 DS1 DS2 DS4 DSPI_SCK DS7 (CPOL=0) DSPI_SIN DS8 Data First data Last data DS5 DSPI_SOUT First data DS6 Data Last data Figure 19. DSPI classic SPI timing -- master mode K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 53 Peripheral operating requirements and behaviors Table 39. Slave mode DSPI timing (limited voltage range) Num Description Operating voltage Min. Max. Unit 2.7 3.6 V 12.5 MHz 4 x tBUS -- ns (tSCK/2) - 2 (tSCK/2) + 2 ns Frequency of operation DS9 DSPI_SCK input cycle time DS10 DSPI_SCK input high/low time DS11 DSPI_SCK to DSPI_SOUT valid -- 20 ns DS12 DSPI_SCK to DSPI_SOUT invalid 0 -- ns DS13 DSPI_SIN to DSPI_SCK input setup 2 -- ns DS14 DSPI_SCK to DSPI_SIN input hold 7 -- ns DS15 DSPI_SS active to DSPI_SOUT driven -- 14 ns DS16 DSPI_SS inactive to DSPI_SOUT not driven -- 14 ns DSPI_SS DS10 DS9 DSPI_SCK DS15 (CPOL=0) DSPI_SOUT DS12 First data DS13 DSPI_SIN DS16 DS11 Last data Data DS14 First data Data Last data Figure 20. DSPI classic SPI timing -- slave mode 6.8.3 DSPI switching specifications (full voltage range) The DMA Serial Peripheral Interface (DSPI) provides a synchronous serial bus with master and slave operations. Many of the transfer attributes are programmable. The tables below provides DSPI timing characteristics for classic SPI timing modes. Refer to the DSPI chapter of the Reference Manual for information on the modified transfer formats used for communicating with slower peripheral devices. Table 40. Master mode DSPI timing (full voltage range) Num Description Operating voltage Frequency of operation DS1 DSPI_SCK output cycle time Min. Max. Unit Notes 1 1.71 3.6 V -- 12.5 MHz 4 x tBUS -- ns Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 54 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 40. Master mode DSPI timing (full voltage range) (continued) Num Description Min. Max. Unit Notes DS2 DSPI_SCK output high/low time (tSCK/2) - 4 (tSCK/2) + 4 ns DS3 DSPI_PCSn valid to DSPI_SCK delay (tBUS x 2) - 4 -- ns 2 DS4 DSPI_SCK to DSPI_PCSn invalid delay (tBUS x 2) - 4 -- ns 3 DS5 DSPI_SCK to DSPI_SOUT valid -- 8.5 ns DS6 DSPI_SCK to DSPI_SOUT invalid -1.2 -- ns DS7 DSPI_SIN to DSPI_SCK input setup 19.1 -- ns DS8 DSPI_SCK to DSPI_SIN input hold 0 -- ns 1. The DSPI module can operate across the entire operating voltage for the processor, but to run across the full voltage range the maximum frequency of operation is reduced. 2. The delay is programmable in SPIx_CTARn[PSSCK] and SPIx_CTARn[CSSCK]. 3. The delay is programmable in SPIx_CTARn[PASC] and SPIx_CTARn[ASC]. DSPI_PCSn DS3 DS1 DS2 DS4 DSPI_SCK DS8 DS7 (CPOL=0) DSPI_SIN Data First data Last data DS5 DSPI_SOUT First data DS6 Data Last data Figure 21. DSPI classic SPI timing -- master mode Table 41. Slave mode DSPI timing (full voltage range) Num Description Operating voltage Frequency of operation Min. Max. Unit 1.71 3.6 V -- 6.25 MHz 8 x tBUS -- ns DS9 DSPI_SCK input cycle time DS10 DSPI_SCK input high/low time (tSCK/2) - 4 (tSCK/2) + 4 ns DS11 DSPI_SCK to DSPI_SOUT valid -- 24 ns DS12 DSPI_SCK to DSPI_SOUT invalid 0 -- ns DS13 DSPI_SIN to DSPI_SCK input setup 3.2 -- ns DS14 DSPI_SCK to DSPI_SIN input hold 7 -- ns DS15 DSPI_SS active to DSPI_SOUT driven -- 19 ns DS16 DSPI_SS inactive to DSPI_SOUT not driven -- 19 ns K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 55 Peripheral operating requirements and behaviors DSPI_SS DS10 DS9 DSPI_SCK DS15 (CPOL=0) DSPI_SOUT DS12 First data DS13 DSPI_SIN DS16 DS11 Last data Data DS14 First data Data Last data Figure 22. DSPI classic SPI timing -- slave mode 6.8.4 Inter-Integrated Circuit Interface (I2C) timing Table 42. I 2C timing Characteristic Symbol Standard Mode Fast Mode Unit Minimum Maximum Minimum Maximum SCL Clock Frequency fSCL 0 100 0 400 kHz Hold time (repeated) START condition. After this period, the first clock pulse is generated. tHD; STA 4 -- 0.6 -- s LOW period of the SCL clock tLOW 4.7 -- 1.3 -- s HIGH period of the SCL clock tHIGH 4 -- 0.6 -- s Set-up time for a repeated START condition tSU; STA 4.7 -- 0.6 -- s Data hold time for I2C bus devices tHD; DAT 01 3.452 03 0.91 s tSU; DAT 2504 -- 1002, 5 Data set-up time -- ns 6 Rise time of SDA and SCL signals tr -- 1000 20 +0.1Cb 300 ns Fall time of SDA and SCL signals tf -- 300 20 +0.1Cb5 300 ns Set-up time for STOP condition tSU; STO 4 -- 0.6 -- s Bus free time between STOP and START condition tBUF 4.7 -- 1.3 -- s Pulse width of spikes that must be suppressed by the input filter tSP N/A N/A 0 50 ns 1. The master mode I2C deasserts ACK of an address byte simultaneously with the falling edge of SCL. If no slaves acknowledge this address byte, then a negative hold time can result, depending on the edge rates of the SDA and SCL lines. 2. The maximum tHD; DAT must be met only if the device does not stretch the LOW period (tLOW) of the SCL signal. 3. Input signal Slew = 10 ns and Output Load = 50 pF 4. Set-up time in slave-transmitter mode is 1 IPBus clock period, if the TX FIFO is empty. 5. A Fast mode I2C bus device can be used in a Standard mode I2C bus system, but the requirement tSU; DAT 250 ns must then be met. This is automatically the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, then it must output the next data bit to the SDA line trmax + tSU; DAT = 1000 + 250 = 1250 ns (according to the Standard mode I2C bus specification) before the SCL line is released. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 56 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors 6. Cb = total capacitance of the one bus line in pF. SDA tf tLOW tSU; DAT tr tf tHD; STA tSP tr tBUF SCL S tHD; STA tHD; DAT tHIGH tSU; STA tSU; STO SR P S Figure 23. Timing definition for fast and standard mode devices on the I2C bus 6.8.5 UART switching specifications See General switching specifications. 6.8.6 SDHC specifications The following timing specs are defined at the chip I/O pin and must be translated appropriately to arrive at timing specs/constraints for the physical interface. Table 43. SDHC switching specifications Num Symbol Description Min. Max. Unit Operating voltage 1.71 3.6 V Card input clock SD1 fpp Clock frequency (low speed) 0 400 kHz fpp Clock frequency (SD\SDIO full speed\high speed) 0 25\50 MHz fpp Clock frequency (MMC full speed\high speed) 0 20\50 MHz fOD Clock frequency (identification mode) 0 400 kHz tWL Clock low time 7 -- ns SD3 tWH Clock high time 7 -- ns SD4 tTLH Clock rise time -- 3 ns SD5 tTHL Clock fall time -- 3 ns SD2 SDHC output / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK) SD6 tOD SDHC output delay (output valid) -5 8.3 ns SDHC input / card inputs SDHC_CMD, SDHC_DAT (reference to SDHC_CLK) SD7 tISU SDHC input setup time 5 -- ns SD8 tIH SDHC input hold time 0 -- ns K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 57 Peripheral operating requirements and behaviors SD3 SD2 SD1 SDHC_CLK SD6 Output SDHC_CMD Output SDHC_DAT[3:0] SD7 SD8 Input SDHC_CMD Input SDHC_DAT[3:0] Figure 24. SDHC timing 6.8.7 I2S/SAI switching specifications This section provides the AC timing for the I2S/SAI module in master mode (clocks are driven) and slave mode (clocks are input). All timing is given for noninverted serial clock polarity (TCR2[BCP] is 0, RCR2[BCP] is 0) and a noninverted frame sync (TCR4[FSP] is 0, RCR4[FSP] is 0). If the polarity of the clock and/or the frame sync have been inverted, all the timing remains valid by inverting the bit clock signal (BCLK) and/or the frame sync (FS) signal shown in the following figures. 6.8.7.1 Normal Run, Wait and Stop mode performance over a limited operating voltage range This section provides the operating performance over a limited operating voltage for the device in Normal Run, Wait and Stop modes. Table 44. I2S/SAI master mode timing in Normal Run, Wait and Stop modes (limited voltage range) Num. Characteristic Min. Max. Unit Operating voltage 2.7 3.6 V S1 I2S_MCLK cycle time 40 -- ns S2 I2S_MCLK pulse width high/low 45% 55% MCLK period S3 I2S_TX_BCLK/I2S_RX_BCLK cycle time (output) 80 -- ns S4 I2S_TX_BCLK/I2S_RX_BCLK pulse width high/low 45% 55% BCLK period S5 I2S_TX_BCLK/I2S_RX_BCLK to I2S_TX_FS/ I2S_RX_FS output valid -- 15 ns Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 58 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 44. I2S/SAI master mode timing in Normal Run, Wait and Stop modes (limited voltage range) (continued) Num. Characteristic Min. Max. Unit S6 I2S_TX_BCLK/I2S_RX_BCLK to I2S_TX_FS/ I2S_RX_FS output invalid 0 -- ns S7 I2S_TX_BCLK to I2S_TXD valid -- 15 ns S8 I2S_TX_BCLK to I2S_TXD invalid 0 -- ns S9 I2S_RXD/I2S_RX_FS input setup before I2S_RX_BCLK 15 -- ns S10 I2S_RXD/I2S_RX_FS input hold after I2S_RX_BCLK 0 -- ns S1 S2 S2 I2S_MCLK (output) S3 I2S_TX_BCLK/ I2S_RX_BCLK (output) S4 S4 S6 S5 I2S_TX_FS/ I2S_RX_FS (output) S10 S9 I2S_TX_FS/ I2S_RX_FS (input) S7 S8 S7 S8 I2S_TXD S9 S10 I2S_RXD Figure 25. I2S/SAI timing -- master modes Table 45. I2S/SAI slave mode timing in Normal Run, Wait and Stop modes (limited voltage range) Num. Characteristic Min. Max. Unit Operating voltage 2.7 3.6 V S11 I2S_TX_BCLK/I2S_RX_BCLK cycle time (input) 80 -- ns S12 I2S_TX_BCLK/I2S_RX_BCLK pulse width high/low (input) 45% 55% MCLK period S13 I2S_TX_FS/I2S_RX_FS input setup before I2S_TX_BCLK/I2S_RX_BCLK 4.5 -- ns S14 I2S_TX_FS/I2S_RX_FS input hold after I2S_TX_BCLK/I2S_RX_BCLK 2 -- ns S15 I2S_TX_BCLK to I2S_TXD/I2S_TX_FS output valid -- 21 -- 15 * Multiple SAI Synchronous mode * All other modes ns Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 59 Peripheral operating requirements and behaviors Table 45. I2S/SAI slave mode timing in Normal Run, Wait and Stop modes (limited voltage range) (continued) Num. Characteristic Min. Max. Unit S16 I2S_TX_BCLK to I2S_TXD/I2S_TX_FS output invalid 0 -- ns S17 I2S_RXD setup before I2S_RX_BCLK 4.5 -- ns S18 I2S_RXD hold after I2S_RX_BCLK 2 -- ns -- 25 ns S19 I2S_TX_FS input assertion to I2S_TXD output valid1 1. Applies to first bit in each frame and only if the TCR4[FSE] bit is clear S11 S12 I2S_TX_BCLK/ I2S_RX_BCLK (input) S12 S15 S16 I2S_TX_FS/ I2S_RX_FS (output) S13 I2S_TX_FS/ I2S_RX_FS (input) S19 S14 S15 S16 S15 S16 I2S_TXD S17 S18 I2S_RXD Figure 26. I2S/SAI timing -- slave modes 6.8.7.2 Normal Run, Wait and Stop mode performance over the full operating voltage range This section provides the operating performance over the full operating voltage for the device in Normal Run, Wait and Stop modes. Table 46. I2S/SAI master mode timing in Normal Run, Wait and Stop modes (full voltage range) Num. Characteristic Min. Max. Unit Operating voltage 1.71 3.6 V S1 I2S_MCLK cycle time 40 -- ns S2 I2S_MCLK pulse width high/low 45% 55% MCLK period S3 I2S_TX_BCLK/I2S_RX_BCLK cycle time (output) 80 -- ns S4 I2S_TX_BCLK/I2S_RX_BCLK pulse width high/low 45% 55% BCLK period S5 I2S_TX_BCLK/I2S_RX_BCLK to I2S_TX_FS/ I2S_RX_FS output valid -- 15 ns S6 I2S_TX_BCLK/I2S_RX_BCLK to I2S_TX_FS/ I2S_RX_FS output invalid -1.0 -- ns Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 60 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 46. I2S/SAI master mode timing in Normal Run, Wait and Stop modes (full voltage range) (continued) Num. Characteristic Min. Max. Unit S7 I2S_TX_BCLK to I2S_TXD valid -- 15 ns S8 I2S_TX_BCLK to I2S_TXD invalid 0 -- ns S9 I2S_RXD/I2S_RX_FS input setup before I2S_RX_BCLK 20.5 -- ns S10 I2S_RXD/I2S_RX_FS input hold after I2S_RX_BCLK 0 -- ns S1 S2 S2 I2S_MCLK (output) S3 I2S_TX_BCLK/ I2S_RX_BCLK (output) S4 S4 S6 S5 I2S_TX_FS/ I2S_RX_FS (output) S10 S9 I2S_TX_FS/ I2S_RX_FS (input) S7 S8 S7 S8 I2S_TXD S9 S10 I2S_RXD Figure 27. I2S/SAI timing -- master modes Table 47. I2S/SAI slave mode timing in Normal Run, Wait and Stop modes (full voltage range) Num. Characteristic Min. Max. Unit Operating voltage 1.71 3.6 V S11 I2S_TX_BCLK/I2S_RX_BCLK cycle time (input) 80 -- ns S12 I2S_TX_BCLK/I2S_RX_BCLK pulse width high/low (input) 45% 55% MCLK period S13 I2S_TX_FS/I2S_RX_FS input setup before I2S_TX_BCLK/I2S_RX_BCLK 5.8 -- ns S14 I2S_TX_FS/I2S_RX_FS input hold after I2S_TX_BCLK/I2S_RX_BCLK 2 -- ns S15 I2S_TX_BCLK to I2S_TXD/I2S_TX_FS output valid -- 24 -- 20.6 0 -- * Multiple SAI Synchronous mode * All other modes S16 I2S_TX_BCLK to I2S_TXD/I2S_TX_FS output invalid ns ns Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 61 Peripheral operating requirements and behaviors Table 47. I2S/SAI slave mode timing in Normal Run, Wait and Stop modes (full voltage range) (continued) Num. Characteristic Min. S17 I2S_RXD setup before I2S_RX_BCLK S18 I2S_RXD hold after I2S_RX_BCLK S19 I2S_TX_FS input assertion to I2S_TXD output valid1 Max. Unit 5.8 -- ns 2 -- ns -- 25 ns 1. Applies to first bit in each frame and only if the TCR4[FSE] bit is clear S11 S12 I2S_TX_BCLK/ I2S_RX_BCLK (input) S12 S15 S16 I2S_TX_FS/ I2S_RX_FS (output) S13 I2S_TX_FS/ I2S_RX_FS (input) S19 S14 S15 S16 S15 S16 I2S_TXD S17 S18 I2S_RXD Figure 28. I2S/SAI timing -- slave modes 6.8.7.3 VLPR, VLPW, and VLPS mode performance over the full operating voltage range This section provides the operating performance over the full operating voltage for the device in VLPR, VLPW, and VLPS modes. Table 48. I2S/SAI master mode timing in VLPR, VLPW, and VLPS modes (full voltage range) Num. Characteristic Min. Max. Unit Operating voltage 1.71 3.6 V S1 I2S_MCLK cycle time 62.5 -- ns S2 I2S_MCLK pulse width high/low 45% 55% MCLK period S3 I2S_TX_BCLK/I2S_RX_BCLK cycle time (output) 250 -- ns S4 I2S_TX_BCLK/I2S_RX_BCLK pulse width high/low 45% 55% BCLK period S5 I2S_TX_BCLK/I2S_RX_BCLK to I2S_TX_FS/ I2S_RX_FS output valid -- 45 ns S6 I2S_TX_BCLK/I2S_RX_BCLK to I2S_TX_FS/ I2S_RX_FS output invalid 0 -- ns S7 I2S_TX_BCLK to I2S_TXD valid -- 45 ns Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 62 Freescale Semiconductor, Inc. Peripheral operating requirements and behaviors Table 48. I2S/SAI master mode timing in VLPR, VLPW, and VLPS modes (full voltage range) (continued) Num. Characteristic Min. Max. Unit S8 I2S_TX_BCLK to I2S_TXD invalid 0 -- ns S9 I2S_RXD/I2S_RX_FS input setup before I2S_RX_BCLK 45 -- ns S10 I2S_RXD/I2S_RX_FS input hold after I2S_RX_BCLK 0 -- ns S1 S2 S2 I2S_MCLK (output) S3 I2S_TX_BCLK/ I2S_RX_BCLK (output) S4 S4 S6 S5 I2S_TX_FS/ I2S_RX_FS (output) S10 S9 I2S_TX_FS/ I2S_RX_FS (input) S7 S8 S7 S8 I2S_TXD S9 S10 I2S_RXD Figure 29. I2S/SAI timing -- master modes Table 49. I2S/SAI slave mode timing in VLPR, VLPW, and VLPS modes (full voltage range) Num. Characteristic Min. Max. Unit Operating voltage 1.71 3.6 V S11 I2S_TX_BCLK/I2S_RX_BCLK cycle time (input) 250 -- ns S12 I2S_TX_BCLK/I2S_RX_BCLK pulse width high/low (input) 45% 55% MCLK period S13 I2S_TX_FS/I2S_RX_FS input setup before I2S_TX_BCLK/I2S_RX_BCLK 30 -- ns S14 I2S_TX_FS/I2S_RX_FS input hold after I2S_TX_BCLK/I2S_RX_BCLK 3 -- ns S15 I2S_TX_BCLK to I2S_TXD/I2S_TX_FS output valid -- 63 ns S16 I2S_TX_BCLK to I2S_TXD/I2S_TX_FS output invalid 0 -- ns S17 I2S_RXD setup before I2S_RX_BCLK 30 -- ns S18 I2S_RXD hold after I2S_RX_BCLK 2 -- ns S19 I2S_TX_FS input assertion to I2S_TXD output valid1 -- 72 ns 1. Applies to first bit in each frame and only if the TCR4[FSE] bit is clear K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 63 Peripheral operating requirements and behaviors S11 S12 I2S_TX_BCLK/ I2S_RX_BCLK (input) S12 S15 S16 I2S_TX_FS/ I2S_RX_FS (output) S13 I2S_TX_FS/ I2S_RX_FS (input) S19 S14 S15 S16 S15 S16 I2S_TXD S17 S18 I2S_RXD Figure 30. I2S/SAI timing -- slave modes 6.9 Human-machine interfaces (HMI) 6.9.1 TSI electrical specifications Table 50. TSI electrical specifications Symbol Description Min. Typ. Max. Unit VDDTSI Operating voltage 1.71 -- 3.6 V Target electrode capacitance range 1 20 500 pF 1 fREFmax Reference oscillator frequency -- 8 15 MHz 2, 3 fELEmax Electrode oscillator frequency -- 1 1.8 MHz 2, 4 Internal reference capacitor -- 1 -- pF Oscillator delta voltage -- 500 -- mV 2, 5 A 2, 6 A 2, 7 CELE CREF VDELTA IREF IELE Reference oscillator current source base current * 2 A setting (REFCHRG = 0) * 32 A setting (REFCHRG = 15) Electrode oscillator current source base current * 2 A setting (EXTCHRG = 0) * 32 A setting (EXTCHRG = 15) -- 2 3 -- 36 50 -- 2 3 -- 36 50 Notes Pres5 Electrode capacitance measurement precision -- 8.3333 38400 fF/count 8 Pres20 Electrode capacitance measurement precision -- 8.3333 38400 fF/count 9 Pres100 Electrode capacitance measurement precision -- 8.3333 38400 fF/count 10 0.008 1.46 -- fF/count 11 -- -- 16 bits Response time @ 20 pF 8 15 25 s Current added in run mode -- 55 -- A Low power mode current adder -- 1.3 2.5 A MaxSens Maximum sensitivity Res TCon20 ITSI_RUN ITSI_LP Resolution 12 13 K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 64 Freescale Semiconductor, Inc. Dimensions 1. The TSI module is functional with capacitance values outside this range. However, optimal performance is not guaranteed. 2. Fixed external capacitance of 20 pF. 3. REFCHRG = 2, EXTCHRG=0. 4. REFCHRG = 0, EXTCHRG = 10. 5. VDD = 3.0 V. 6. The programmable current source value is generated by multiplying the SCANC[REFCHRG] value and the base current. 7. The programmable current source value is generated by multiplying the SCANC[EXTCHRG] value and the base current. 8. Measured with a 5 pF electrode, reference oscillator frequency of 10 MHz, PS = 128, NSCN = 8; Iext = 16. 9. Measured with a 20 pF electrode, reference oscillator frequency of 10 MHz, PS = 128, NSCN = 2; Iext = 16. 10. Measured with a 20 pF electrode, reference oscillator frequency of 10 MHz, PS = 16, NSCN = 3; Iext = 16. 11. Sensitivity defines the minimum capacitance change when a single count from the TSI module changes. Sensitivity depends on the configuration used. The documented values are provided as examples calculated for a specific configuration of operating conditions using the following equation: (Cref * Iext)/( Iref * PS * NSCN) The typical value is calculated with the following configuration: Iext = 6 A (EXTCHRG = 2), PS = 128, NSCN = 2, Iref = 16 A (REFCHRG = 7), Cref = 1.0 pF The minimum value is calculated with the following configuration: Iext = 2 A (EXTCHRG = 0), PS = 128, NSCN = 32, Iref = 32 A (REFCHRG = 15), Cref = 0.5 pF The highest possible sensitivity is the minimum value because it represents the smallest possible capacitance that can be measured by a single count. 12. Time to do one complete measurement of the electrode. Sensitivity resolution of 0.0133 pF, PS = 0, NSCN = 0, 1 electrode, EXTCHRG = 7. 13. REFCHRG=0, EXTCHRG=4, PS=7, NSCN=0F, LPSCNITV=F, LPO is selected (1 kHz), and fixed external capacitance of 20 pF. Data is captured with an average of 7 periods window. 7 Dimensions 7.1 Obtaining package dimensions Package dimensions are provided in package drawings. To find a package drawing, go to freescale.com and perform a keyword search for the drawing's document number: If you want the drawing for this package 121-pin MAPBGA Then use this document number 98ASA00344D 8 Pinout K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 65 Pinout 8.1 K10 signal multiplexing and pin assignments The following table shows the signals available on each pin and the locations of these pins on the devices supported by this document. The Port Control Module is responsible for selecting which ALT functionality is available on each pin. 121 MAP BGA Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 E4 PTE0 ADC1_SE4a ADC1_SE4a PTE0 SPI1_PCS1 UART1_TX SDHC0_D1 I2C1_SDA RTC_CLKOUT E3 PTE1/ LLWU_P0 ADC1_SE5a ADC1_SE5a PTE1/ LLWU_P0 SPI1_SOUT UART1_RX SDHC0_D0 I2C1_SCL SPI1_SIN E2 PTE2/ LLWU_P1 ADC1_SE6a ADC1_SE6a PTE2/ LLWU_P1 SPI1_SCK UART1_CTS_b SDHC0_DCLK F4 PTE3 ADC1_SE7a ADC1_SE7a PTE3 SPI1_SIN UART1_RTS_b SDHC0_CMD E7 VDD VDD VDD F7 VSS VSS VSS H7 PTE4/ LLWU_P2 DISABLED PTE4/ LLWU_P2 SPI1_PCS0 UART3_TX SDHC0_D3 G4 PTE5 DISABLED PTE5 SPI1_PCS2 UART3_RX SDHC0_D2 PTE6 SPI1_PCS3 UART3_CTS_b I2S0_MCLK SPI1_SOUT F3 PTE6 DISABLED E6 VDD VDD VDD G7 VSS VSS VSS F1 PTE16 ADC0_SE4a ADC0_SE4a PTE16 SPI0_PCS0 UART2_TX FTM_CLKIN0 FTM0_FLT3 F2 PTE17 ADC0_SE5a ADC0_SE5a PTE17 SPI0_SCK UART2_RX FTM_CLKIN1 LPTMR0_ALT3 G1 PTE18 ADC0_SE6a ADC0_SE6a PTE18 SPI0_SOUT UART2_CTS_b I2C0_SDA G2 PTE19 ADC0_SE7a ADC0_SE7a PTE19 SPI0_SIN UART2_RTS_b I2C0_SCL L6 VSS VSS VSS H1 ADC0_DP1 ADC0_DP1 ADC0_DP1 H2 ADC0_DM1 ADC0_DM1 ADC0_DM1 J1 ADC1_DP1 ADC1_DP1 ADC1_DP1 J2 ADC1_DM1 ADC1_DM1 ADC1_DM1 K1 PGA0_DP/ ADC0_DP0/ ADC1_DP3 PGA0_DP/ ADC0_DP0/ ADC1_DP3 PGA0_DP/ ADC0_DP0/ ADC1_DP3 K2 PGA0_DM/ ADC0_DM0/ ADC1_DM3 PGA0_DM/ ADC0_DM0/ ADC1_DM3 PGA0_DM/ ADC0_DM0/ ADC1_DM3 L1 PGA1_DP/ ADC1_DP0/ ADC0_DP3 PGA1_DP/ ADC1_DP0/ ADC0_DP3 PGA1_DP/ ADC1_DP0/ ADC0_DP3 L2 PGA1_DM/ ADC1_DM0/ ADC0_DM3 PGA1_DM/ ADC1_DM0/ ADC0_DM3 PGA1_DM/ ADC1_DM0/ ADC0_DM3 F5 VDDA VDDA VDDA G5 VREFH VREFH VREFH G6 VREFL VREFL VREFL EzPort K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 66 Freescale Semiconductor, Inc. Pinout 121 MAP BGA Pin Name Default ALT0 F6 VSSA VSSA VSSA J3 ADC1_SE16/ CMP2_IN2/ ADC0_SE22 ADC1_SE16/ CMP2_IN2/ ADC0_SE22 ADC1_SE16/ CMP2_IN2/ ADC0_SE22 H3 ADC0_SE16/ CMP1_IN2/ ADC0_SE21 ADC0_SE16/ CMP1_IN2/ ADC0_SE21 ADC0_SE16/ CMP1_IN2/ ADC0_SE21 L3 VREF_OUT/ CMP1_IN5/ CMP0_IN5/ ADC1_SE18 VREF_OUT/ CMP1_IN5/ CMP0_IN5/ ADC1_SE18 VREF_OUT/ CMP1_IN5/ CMP0_IN5/ ADC1_SE18 K5 DAC0_OUT/ CMP1_IN3/ ADC0_SE23 DAC0_OUT/ CMP1_IN3/ ADC0_SE23 DAC0_OUT/ CMP1_IN3/ ADC0_SE23 K4 DAC1_OUT/ CMP0_IN4/ CMP2_IN3/ ADC1_SE23 DAC1_OUT/ CMP0_IN4/ CMP2_IN3/ ADC1_SE23 DAC1_OUT/ CMP0_IN4/ CMP2_IN3/ ADC1_SE23 L7 RTC_ WAKEUP_B RTC_ WAKEUP_B RTC_ WAKEUP_B L4 XTAL32 XTAL32 XTAL32 L5 EXTAL32 EXTAL32 EXTAL32 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 ALT7 EzPort K6 VBAT VBAT VBAT H5 PTE24 ADC0_SE17 ADC0_SE17 PTE24 CAN1_TX UART4_TX EWM_OUT_b J5 PTE25 ADC0_SE18 ADC0_SE18 PTE25 CAN1_RX UART4_RX EWM_IN H6 PTE26 DISABLED UART4_CTS_b RTC_CLKOUT J6 PTA0 JTAG_TCLK/ SWD_CLK/ EZP_CLK TSI0_CH1 PTA0 UART0_CTS_ FTM0_CH5 b/ UART0_COL_b JTAG_TCLK/ SWD_CLK EZP_CLK H8 PTA1 JTAG_TDI/ EZP_DI TSI0_CH2 PTA1 UART0_RX FTM0_CH6 JTAG_TDI EZP_DI J7 PTA2 JTAG_TDO/ TRACE_SWO/ EZP_DO TSI0_CH3 PTA2 UART0_TX FTM0_CH7 JTAG_TDO/ TRACE_SWO EZP_DO H9 PTA3 JTAG_TMS/ SWD_DIO TSI0_CH4 PTA3 UART0_RTS_b FTM0_CH0 J8 PTA4/ LLWU_P3 NMI_b/ EZP_CS_b TSI0_CH5 PTA4/ LLWU_P3 FTM0_CH1 K7 PTA5 DISABLED PTA5 FTM0_CH2 PTE26 JTAG_TMS/ SWD_DIO NMI_b CMP2_OUT I2S0_TX_BCLK JTAG_TRST_b E5 VDD VDD VDD G3 VSS VSS VSS J9 PTA10 DISABLED PTA10 FTM2_CH0 FTM2_QD_ PHA J4 PTA11 DISABLED PTA11 FTM2_CH1 FTM2_QD_ PHB K8 PTA12 CMP2_IN0 FTM1_CH0 I2S0_TXD0 CMP2_IN0 PTA12 CAN0_TX EZP_CS_b TRACE_D0 FTM1_QD_ PHA K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 67 Pinout 121 MAP BGA Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 CMP2_IN1 PTA13/ LLWU_P4 CAN0_RX FTM1_CH1 I2S0_TX_FS ALT7 L8 PTA13/ LLWU_P4 CMP2_IN1 K9 PTA14 DISABLED PTA14 SPI0_PCS0 UART0_TX I2S0_RX_BCLK I2S0_TXD1 L9 PTA15 DISABLED PTA15 SPI0_SCK UART0_RX I2S0_RXD0 J10 PTA16 DISABLED PTA16 SPI0_SOUT UART0_CTS_ b/ UART0_COL_b I2S0_RX_FS H10 PTA17 ADC1_SE17 ADC1_SE17 PTA17 SPI0_SIN UART0_RTS_b I2S0_MCLK L10 VDD VDD VDD K10 VSS VSS VSS L11 PTA18 EXTAL0 EXTAL0 PTA18 FTM0_FLT2 FTM_CLKIN0 K11 PTA19 XTAL0 XTAL0 PTA19 FTM1_FLT0 FTM_CLKIN1 J11 RESET_b RESET_b RESET_b H11 PTA29 DISABLED G11 PTB0/ LLWU_P5 ADC0_SE8/ ADC1_SE8/ TSI0_CH0 ADC0_SE8/ ADC1_SE8/ TSI0_CH0 PTB0/ LLWU_P5 I2C0_SCL FTM1_CH0 FTM1_QD_ PHA G10 PTB1 ADC0_SE9/ ADC1_SE9/ TSI0_CH6 ADC0_SE9/ ADC1_SE9/ TSI0_CH6 PTB1 I2C0_SDA FTM1_CH1 FTM1_QD_ PHB G9 PTB2 ADC0_SE12/ TSI0_CH7 ADC0_SE12/ TSI0_CH7 PTB2 I2C0_SCL UART0_RTS_b FTM0_FLT3 G8 PTB3 ADC0_SE13/ TSI0_CH8 ADC0_SE13/ TSI0_CH8 PTB3 I2C0_SDA UART0_CTS_ b/ UART0_COL_b FTM0_FLT0 FTM1_QD_ PHB I2S0_RXD1 LPTMR0_ALT1 PTA29 FB_A24 F11 PTB6 ADC1_SE12 ADC1_SE12 PTB6 FB_AD23 E11 PTB7 ADC1_SE13 ADC1_SE13 PTB7 FB_AD22 D11 PTB8 DISABLED PTB8 E10 PTB9 DISABLED PTB9 D10 PTB10 ADC1_SE14 ADC1_SE14 C10 PTB11 ADC1_SE15 B10 PTB16 E9 UART3_RTS_b FB_AD21 SPI1_PCS1 UART3_CTS_b FB_AD20 PTB10 SPI1_PCS0 UART3_RX FB_AD19 FTM0_FLT1 ADC1_SE15 PTB11 SPI1_SCK UART3_TX FB_AD18 FTM0_FLT2 TSI0_CH9 TSI0_CH9 PTB16 SPI1_SOUT UART0_RX FB_AD17 EWM_IN PTB17 TSI0_CH10 TSI0_CH10 PTB17 SPI1_SIN UART0_TX FB_AD16 EWM_OUT_b D9 PTB18 TSI0_CH11 TSI0_CH11 PTB18 CAN0_TX FTM2_CH0 I2S0_TX_BCLK FB_AD15 FTM2_QD_ PHA C9 PTB19 TSI0_CH12 TSI0_CH12 PTB19 CAN0_RX FTM2_CH1 I2S0_TX_FS FB_OE_b FTM2_QD_ PHB F10 PTB20 DISABLED PTB20 SPI2_PCS0 FB_AD31 CMP0_OUT F9 PTB21 DISABLED PTB21 SPI2_SCK FB_AD30 CMP1_OUT FB_AD29 CMP2_OUT F8 PTB22 DISABLED PTB22 SPI2_SOUT E8 PTB23 DISABLED PTB23 SPI2_SIN SPI0_PCS5 FB_AD28 B9 PTC0 ADC0_SE14/ TSI0_CH13 PTC0 SPI0_PCS4 PDB0_EXTRG FB_AD14 ADC0_SE14/ TSI0_CH13 EzPort I2S0_TXD1 K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 68 Freescale Semiconductor, Inc. Pinout 121 MAP BGA Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 D8 PTC1/ LLWU_P6 ADC0_SE15/ TSI0_CH14 ADC0_SE15/ TSI0_CH14 PTC1/ LLWU_P6 SPI0_PCS3 UART1_RTS_b FTM0_CH0 FB_AD13 I2S0_TXD0 C8 PTC2 ADC0_SE4b/ CMP1_IN0/ TSI0_CH15 ADC0_SE4b/ CMP1_IN0/ TSI0_CH15 PTC2 SPI0_PCS2 UART1_CTS_b FTM0_CH1 FB_AD12 I2S0_TX_FS B8 PTC3/ LLWU_P7 CMP1_IN1 CMP1_IN1 PTC3/ LLWU_P7 SPI0_PCS1 UART1_RX FTM0_CH2 CLKOUT I2S0_TX_BCLK A8 PTC4/ LLWU_P8 DISABLED PTC4/ LLWU_P8 SPI0_PCS0 UART1_TX FTM0_CH3 FB_AD11 CMP1_OUT D7 PTC5/ LLWU_P9 DISABLED PTC5/ LLWU_P9 SPI0_SCK LPTMR0_ALT2 I2S0_RXD0 FB_AD10 CMP0_OUT C7 PTC6/ LLWU_P10 CMP0_IN0 CMP0_IN0 PTC6/ LLWU_P10 SPI0_SOUT PDB0_EXTRG B7 PTC7 CMP0_IN1 CMP0_IN1 PTC7 SPI0_SIN A7 PTC8 ADC1_SE4b/ CMP0_IN2 ADC1_SE4b/ CMP0_IN2 D6 PTC9 ADC1_SE5b/ CMP0_IN3 C6 PTC10 C5 PTC11/ LLWU_P11 B6 PTC12 DISABLED PTC12 UART4_RTS_b FB_AD27 A6 PTC13 DISABLED PTC13 UART4_CTS_b FB_AD26 A5 PTC14 DISABLED PTC14 UART4_RX FB_AD25 B5 PTC15 DISABLED PTC15 UART4_TX FB_AD24 D5 PTC16 DISABLED PTC16 CAN1_RX UART3_RX FB_CS5_b/ FB_TSIZ1/ FB_BE23_16_b C4 PTC17 DISABLED PTC17 CAN1_TX UART3_TX FB_CS4_b/ FB_TSIZ0/ FB_BE31_24_b B4 PTC18 DISABLED PTC18 UART3_RTS_b FB_TBST_b/ FB_CS2_b/ FB_BE15_8_b A4 PTC19 DISABLED PTC19 UART3_CTS_b FB_CS3_b/ FB_BE7_0_b D4 PTD0/ LLWU_P12 DISABLED PTD0/ LLWU_P12 SPI0_PCS0 UART2_RTS_b FB_ALE/ FB_CS1_b/ FB_TS_b D3 PTD1 ADC0_SE5b PTD1 SPI0_SCK UART2_CTS_b FB_CS0_b C3 PTD2/ LLWU_P13 DISABLED PTD2/ LLWU_P13 SPI0_SOUT UART2_RX FB_AD4 B3 PTD3 DISABLED PTD3 SPI0_SIN UART2_TX FB_AD3 A3 PTD4/ LLWU_P14 DISABLED PTD4/ LLWU_P14 SPI0_PCS1 UART0_RTS_b FTM0_CH4 FB_AD2 I2S0_RX_BCLK FB_AD9 I2S0_RX_FS FB_AD8 PTC8 I2S0_MCLK FB_AD7 ADC1_SE5b/ CMP0_IN3 PTC9 I2S0_RX_BCLK FB_AD6 ADC1_SE6b ADC1_SE6b PTC10 I2C1_SCL I2S0_RX_FS FB_AD5 ADC1_SE7b ADC1_SE7b PTC11/ LLWU_P11 I2C1_SDA I2S0_RXD1 FB_RW_b ADC0_SE5b ALT7 EzPort I2S0_MCLK FTM2_FLT0 FB_TA_b EWM_IN K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 69 Pinout 121 MAP BGA Pin Name Default ALT0 ALT1 ALT2 ALT3 ALT4 ALT5 ALT6 A2 PTD5 ADC0_SE6b ADC0_SE6b PTD5 SPI0_PCS2 UART0_CTS_ FTM0_CH5 b/ UART0_COL_b FB_AD1 EWM_OUT_b B2 PTD6/ LLWU_P15 ADC0_SE7b ADC0_SE7b PTD6/ LLWU_P15 SPI0_PCS3 UART0_RX FTM0_CH6 FB_AD0 FTM0_FLT0 A1 PTD7 DISABLED PTD7 CMT_IRO UART0_TX FTM0_CH7 A10 PTD8 DISABLED PTD8 I2C0_SCL UART5_RX FB_A16 A9 PTD9 DISABLED PTD9 I2C0_SDA UART5_TX FB_A17 UART5_RTS_b FB_A18 UART5_CTS_b SDHC0_CLKIN FB_A19 ALT7 EzPort FTM0_FLT1 B1 PTD10 DISABLED PTD10 C2 PTD11 DISABLED PTD11 SPI2_PCS0 C1 PTD12 DISABLED PTD12 SPI2_SCK SDHC0_D4 FB_A20 D2 PTD13 DISABLED PTD13 SPI2_SOUT SDHC0_D5 FB_A21 D1 PTD14 DISABLED PTD14 SPI2_SIN SDHC0_D6 FB_A22 E1 PTD15 DISABLED PTD15 SPI2_PCS1 SDHC0_D7 FB_A23 A11 NC NC NC B11 NC NC NC C11 NC NC NC K3 NC NC NC H4 NC NC NC 8.2 K10 pinouts The figure below shows the pinout diagram for the devices supported by this document. Many signals may be multiplexed onto a single pin. To determine what signals can be used on which pin, see the previous section. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 70 Freescale Semiconductor, Inc. Revision history 1 2 3 4 5 6 7 8 9 10 11 A PTD7 PTD5 PTD4/ LLWU_P14 PTC19 PTC14 PTC13 PTC8 PTC4/ LLWU_P8 PTD9 PTD8 NC A B PTD10 PTD6/ LLWU_P15 PTD3 PTC18 PTC15 PTC12 PTC7 PTC3/ LLWU_P7 PTC0 PTB16 NC B C PTD12 PTD11 PTD2/ LLWU_P13 PTC17 PTC11/ LLWU_P11 PTC10 PTC6/ LLWU_P10 PTC2 PTB19 PTB11 NC C D PTD14 PTD13 PTD1 PTD0/ LLWU_P12 PTC16 PTC9 PTC5/ LLWU_P9 PTC1/ LLWU_P6 PTB18 PTB10 PTB8 D E PTD15 PTE2/ LLWU_P1 PTE1/ LLWU_P0 PTE0 VDD VDD VDD PTB23 PTB17 PTB9 PTB7 E F PTE16 PTE17 PTE6 PTE3 VDDA VSSA VSS PTB22 PTB21 PTB20 PTB6 F G PTE18 PTE19 VSS PTE5 VREFH VREFL VSS PTB3 PTB2 PTB1 PTB0/ LLWU_P5 G NC PTE24 PTE26 PTE4/ LLWU_P2 PTA1 PTA3 PTA17 PTA29 H PTA11 PTE25 PTA0 PTA2 PTA4/ LLWU_P3 PTA10 PTA16 RESET_b J VBAT PTA5 PTA12 PTA14 VSS PTA19 K PTA15 VDD PTA18 L 9 10 11 ADC0_SE16/ H ADC0_DP1 ADC0_DM1 CMP1_IN2/ ADC0_SE21 ADC1_SE16/ J ADC1_DP1 ADC1_DM1 CMP2_IN2/ ADC0_SE22 K PGA0_DP/ PGA0_DM/ ADC0_DP0/ ADC0_DM0/ ADC1_DP3 ADC1_DM3 L VREF_OUT/ PGA1_DP/ PGA1_DM/ CMP1_IN5/ ADC1_DP0/ ADC1_DM0/ CMP0_IN5/ ADC0_DP3 ADC0_DM3 ADC1_SE18 1 2 NC 3 DAC1_OUT/ DAC0_OUT/ CMP0_IN4/ CMP1_IN3/ CMP2_IN3/ ADC0_SE23 ADC1_SE23 XTAL32 EXTAL32 VSS 4 5 6 RTC_ PTA13/ WAKEUP_B LLWU_P4 7 8 Figure 31. K10 121 MAPBGA Pinout Diagram 9 Revision history The following table provides a revision history for this document. Table 51. Revision history Rev. No. Date Substantial Changes 1 6/2012 Initial public revision 2 12/2012 Replaced TBDs throughout. Table continues on the next page... K10 Sub-Family Data Sheet, Rev. 3, 6/2013. Freescale Semiconductor, Inc. 71 Revision history Table 51. Revision history (continued) Rev. No. Date 3 6/2013 Substantial Changes * * * * * * * * * In ESD handling ratings, added a note for ILAT. Updated "Voltage and current operating requirements" Table 1. Updated IOL data for VOL row in "Voltage and current operating behaviors" Table 4. Updated wakeup times and tPOR value in "Power mode transition operating behaviors" Table 5. In "EMC radiated emissions operating behaviors . . ." Table 7, added a column for 144MAPBGA. In "16-bit ADC operating conditions" Table 27, updated the max spec of VADIN. In "16-bit ADC electrical characteristics" Table 28, updated the temp sensor slope and voltage specs. Updated Inter-Integrated Circuit Interface (I2C) timing. In SDHC specifications, added operating voltage row. K10 Sub-Family Data Sheet, Rev. 3, 6/2013. 72 Freescale Semiconductor, Inc. How to Reach Us: Information in this document is provided solely to enable system and software Home Page: freescale.com implementers to use Freescale products. There are no express or implied copyright Web Support: freescale.com/support information in this document. licenses granted hereunder to design or fabricate any integrated circuits based on the Freescale reserves the right to make changes without further notice to any products herein. Freescale makes no warranty, representation, or guarantee regarding the suitability of its products for any particular purpose, nor does Freescale assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters that may be provided in Freescale data sheets and/or specifications can and do vary in different applications, and actual performance may vary over time. All operating parameters, including "typicals," must be validated for each customer application by customer's technical experts. Freescale does not convey any license under its patent rights nor the rights of others. Freescale sells products pursuant to standard terms and conditions of sale, which can be found at the following address: freescale.com/SalesTermsandConditions. Freescale, the Freescale logo, AltiVec, C-5, CodeTest, CodeWarrior, ColdFire, C-Ware, Energy Efficient Solutions logo, Kinetis, mobileGT, PowerQUICC, Processor Expert, QorIQ, Qorivva, StarCore, Symphony, and VortiQa are trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. Airfast, BeeKit, BeeStack, ColdFire+, CoreNet, Flexis, MagniV, MXC, Platform in a Package, QorIQ Qonverge, QUICC Engine, Ready Play, SafeAssure, SMARTMOS, TurboLink, Vybrid, and Xtrinsic are trademarks of Freescale Semiconductor, Inc. All other product or service names are the property of their respective owners. ARM, the ARM powered logo, and Coretx are the registered trademarks of ARM Limited. (c) 2012-2013Freescale Semiconductor, Inc. Document Number: K10P121M100SF2V2 Rev. 3 06/2013