H7CX-A11-N - OMRON - Pdf.Support

New Product

Multifunction Counter/Tachometer

H7CX-@-N

Ultra-compact Counter Provides More

Complete Functionality.

Basic Features

•

Short body with depth of only 59 mm (for 12 to 24-VDC Models with Screw Terminals).

• Better readability with character height of 12 mm on 4-digit models and 10 mm

on 6-digit models.

•

The present value display characters can be switched between red, green, and orange.

Safety and Reliability

• New set value limit and counter functions have been added.

Other Features

• Front Panel can be changed to white or light gray.*3

• New models with two tachometer inputs and two tachometer outputs have

been added to the series.*4

*1.For 100 to 240-VAC Models with Screw Terminals: 78 mm, Models with Sockets: 63.7 mm

(case dimension).

*2.The H7CX-A11 and H7CX-R11 have only red characters.

*3.

The Front Panel can be replaced with an optional Front Panel (except for Tachometer-only Models).

*4.Only one prescale value provided.

Features

Basic Features

Ultra Short Body

The body depth has been greatly reduced. Helps in making thinner control panels.

Easier to Read

For better readability, the character height for the present value

display is 12 mm on models with 4 digits, the largest class in the

industry. The wide viewing angle and brightness provide excellent

visibility. The number of display segments has also been increased to

make settings easier to understand, and the present value display

can be switched between red, green, and orange so that output status

can be seen from a distance.

Note: The display color can be switched on all models except for the

H7CX-A11 and H7CX-R11.

The Easiest Operation

Operation is simplified by the

Up/Down Key for each digit

on 4-digit models and Up

Key for each digit on 6-digit

models.

Safety and Reliability

Isolated Power Supply and Input Circuits

Power supply circuit and input circuits are isolated inside the Counter/

Tachometer. Previous non-isolated counters had wiring restrictions

and could be damaged if wired incorrectly. The H7CX removes these

worries.

Note: Except 12 to 24-VDC models.

Set Value Limit

You can set an upper limit for the set value to prevent unexpected

operation of output devices caused by setting mistakes.

Output Counter

The output counter counts the number of times the output turns ON

(alarms can be displayed and the count can be monitored in

increments of 1,000 operations). This counter is useful in managing

the service life of the Counter/Tachometer or the load.

Refer to Safety Precautions on page 52.

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

12 to 24-VDC Models with Screw Terminals: 59 mm

100 to 240-VAC Models with Screw Terminals: 78 mm*

Models with Sockets: 63.7 mm (case dimension)

* Power supply circuit and input circuits are isolated for safety and reliability.

New models

models

12 mm

(actual size)

Model with 4 Digits Model with 6 Digits

10 mm

(actual size)

(Display example)

New

models

Easy to read from the top, bottom,

and sides!

Model with 4 Digits Model with 6 Digits

For 1,000 pieces

No overflow

Setting the upper limit of the set

value enables worry-free operation.

H7CX-@-N

Other Features

The front color can be changed simply by

replacing the Front Panel.

The Front Panel can be replaced with an optional Front Panel (sold

separately) with a different color to match the installation site. Select

from black, white, and light gray (except for models with tachometer

function only).

Universal NPN/PNP Input

DC 2-wire sensors can be connected for a wide range of input

devices.

Waterproof, Dust-proof Structure (UL508 Type

4X and IP66)

Worry-free application is possible in locations subject to water.

Note: When the Y92S-29 Waterproof Packing is used.

Key Protection

Select from any of seven protection patterns. Use the best one for the

application.

New Functions

Many useful functions have been added, including a Twin Counter

Mode and many tachometer functions to handle even more

applications.

New Tachometer Functions

• Control with two independent inputs (independent measurements,

differential, absolute ratio, and error ratio)

• Peak/bottom hold function

• Output hysteresis setting

• Output OFF delay

• Switching the measurement method (pulse cycle/pulse width)

• Startup time

• Auto-zero time

• Averaging method/Number of averaging times

• AMD-compatible Mode

Note: Refer to “Model Configuration” below, for details on applicable

functions.

Model Number Structure

Model Configuration

*1. Set the tachometer input mode from the function setting mode to switch to the tachometer function.

White Light gray

Black

(Standard)

Only the Front

Panel can be

replaced.

H7CX Series

Model

H7CX-A-series Multifunction Preset Counter H7CX-R-series Digital Tachometer

Classification Preset counter Preset counter/tachometer Tachometer

Model H7CX-A@-N H7CX-A4W@-N H7CX-AW@-N/-AU@-N H7CX-R11@-N H7CX-R11W@-N

Function

1-stage preset

counter Yes Yes Yes No

2-stage preset

counter No Yes Yes No

Total and preset

counter Yes Yes Yes No

Batch counter No Yes Yes No

Dual counter No Yes Yes No

Twin counter No Yes Yes No

Tachometer No No Yes*1 Yes

Tachometer input No No

Yes

1 input or 2 inputs

(independent

measurements, differential,

absolute ratio value, and

error ratio value)

Yes

1 input

Yes

2 inputs (independent

measurement) only

Settings 1-stage 2-stage 1-stage

External connections 11-pin socket Screw terminals 11-pin socket

Display color of present value Red Red, green, or orange Red

Display digits 4 or 6 digits 4 digits 6 digits 6 digits

H7CX-@-N

Model Number Legend (Not all possible combinations of functions are available.)

H7CX-@@@@@@-N

123456

Note:

Estimates can be provided for coatings and other specifications that are not given in the datasheet. Ask your OMRON representative for details.

Ordering Information

List of Models

Note: 1. The functions that are provided depend on the model. Check detailed specifications before ordering.

2. Refer to page page 37 and later for information on H7CX-R Tachometers.

Type Classification Configuration External

connections Settings Display

digits Outputs Power supply

voltage Model

H7CX-A

Series

Preset counter

• 1-stage preset

counter

• Total and preset

counter

11-pin socket

1-stage

4 digits

Contact output (SPDT) 100 to 240 VAC H7CX-A114-N

Transistor output (SPST) H7CX-A114S-N

Contact output (SPDT) 12 to 24 VDC/24 VAC H7CX-A114D1-N

6 digits

Contact output (SPDT) 100 to 240 VAC H7CX-A11-N

Transistor output (SPST) H7CX-A11S-N

Contact output (SPDT) 12 to 24 VDC/24 VAC H7CX-A11D1-N

Transistor output (SPST) H7CX-A11SD1-N

Screw

terminals

4 digits

Contact output (SPDT) 100 to 240 VAC H7CX-A4-N

Transistor output (SPST) H7CX-A4S-N

Contact output (SPDT) 12 to 24 VDC H7CX-A4D-N

Transistor output (SPST) H7CX-A4SD-N

6 digits

Contact output (SPDT) 100 to 240 VAC H7CX-A-N

Transistor output (SPST) H7CX-AS-N

Contact output (SPDT) 12 to 24 VDC H7CX-AD-N

Transistor output (SPST) H7CX-ASD-N

• 1-stage preset

counter

• 2-stage preset

counter

• Total and preset

counter

• Batch counter

• Dual counter

• Twin counter

2-stage

4 digits

Contact output (SPST + SPDT) 100 to 240 VAC H7CX-A4W-N

Transistor output (DPST) 12 to 24 VDC H7CX-A4WSD-N

Preset counter/

Tachometer

• 1-stage preset

counter

• 2-stage preset

counter

• Total and preset

counter

• Batch counter

• Dual counter

• Twin counter

• Tachometer

6 digits

Contact output (SPST + SPDT) 100 to 240 VAC H7CX-AW-N

Transistor output (DPST) H7CX-AWS-N

Contact output (SPST + SPDT) 12 to 24 VDC/24 VAC H7CX-AWD1-N

Transistor output (DPST) H7CX-AWSD1-N

12 to 24 VDC H7CX-AWSD-N

Contact output (SPDT) +

Transistor output (SPST) 100 to 240 VAC H7CX-AU-N

Contact output (SPDT) +

Transistor output (SPST) 12 to 24 VDC/24 VAC H7CX-AUD1-N

Transistor output (DPST) H7CX-AUSD1-N

H7CX-R

Series Tachometer • Tachometer 11-pin socket

1-stage

(1 input and

output) 6 digits

Contact output (SPDT)

100 to 240 VAC H7CX-R11-N

12 to 24 VDC/24 VAC H7CX-R11D1-N

1-stage

(2 inputs and

outputs)

Contact output (SPDT + SPST)

100 to 240 VAC H7CX-R11W-N

12 to 24 VDC/24 VAC H7CX-R11WD1-N

4. Settings

* The H7CX-R11W@ is a 1-stage (2 inputs and outputs)

rather than a 2-stage Counter.

5. Output type 6. Supply voltage

Symbol Meaning

None 1-stage setting

U Factory-set to 1-stage setting

W Factory-set to 2-stage setting*

Symbol Meaning

None Contact output or contact output +

transistor output

S Transistor output

Symbol Meaning

None 100 to 240 VAC at 50/60 Hz

D 12 to 24 VDC

D1 12 to 24 VDC/24 VAC at 50/60 Hz

1. Type 2. External connections 3. Digits

Symbol Meaning

A Standard type

R Tachometer

Symbol Meaning

None Screw terminals

11 11-pin socket

Symbol Meaning

None 6 digits

4 4 digits

H7CX-@-N

Accessories (Order Separately)

Front Panels (Replacement Part)

Note: 1. You can change the color of the Front Panel when mounting the Counter. The Counter is shipped with a black (N1.5) Front Panel.

2. "COUNTER" is printed on the front of Replacement Front Panels.

Soft Cover

Hard Cover

Flush Mounting Adapter

Waterproof Packing

Connection Sockets

Terminal Covers for P3GA-11 Back-connecting Socket

Model Color Applicable Counters Page

Y92P-CXC4G Light gray (5Y7/1) 4-digit Counter

Y92P-CXC4S White (5Y9.2/0.5)

Y92P-CXC4B Black (N1.5)

Y92P-CXC6G Light gray (5Y7/1) 6-digit Counter

Y92P-CXC6S White (5Y9.2/0.5)

Y92P-CXC6B Black (N1.5)

Model Remarks Page

Y92A-48F1 --- 12

Model Remarks Page

Y92A-48 --- 12

Model Remarks Page

Y92F-30 Included with models with screw

terminals.

Y92F-45

Use this Adapter to install the Counter/

Tachometer in a cutout previously made

for a DIN 72 × 72 mm device (panel

cutout: 68 × 68 mm).

Model Remarks Page

Y92S-29 Included with models with screw

terminals. 12

Model Classification

Connectable

Counter/

Tachometers

Remarks Page

P2CF-11 Front-connecting Socket

H7CX-@11@-N

---

P2CF-11-E Front-connecting Socket (Finger-safe

Type)

Round crimp terminals cannot be used on

Finger-safe Sockets.

Use forked crimp terminals.

P3GA-11 Back-connecting Sockets

A Y92A-48G Terminal Cover can be used

with the Socket to create a finger-safe

construction.

Model Remarks Page

Y92A-48G --- 13

H7CX-A@-N

• Easy to check the output status from a long distance with

changing display colors*1 (red, green, and orange).

• Includes total and preset counter, batch counter, dual counter,

twin counter, and tachometer.*2

*1. Not supported by the H7CX-A11@-N.

*2. The functions that can be selected depend on the model.

Specifications

Ratings

*1. 1-stage preset counter and total counter functionality.

*2. Do not use the output from an inverter as the power supply.The ripple must be 20% maximum for DC power.

*3. The display is lit only when the power is ON. Nothing is displayed when power is OFF.

H7CX-A@-N Multifunction Preset Counter

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Item Models H7CX-A114@-N H7CX-A11@-N H7CX-A4@-N H7CX-A@-N H7CX-A4W@-N H7CX-AW@-N/-AU@-N

Classification Preset counter Preset counter/

tachometer

Configuration 1-stage preset counter, 1-stage preset counter with total counter (selectable)*1

1-stage/2-stage preset

counter, total and preset

counter*1, batch

counter, dual counter,

and twin counter

(selectable)

1-stage/2-stage preset

counter, total and preset

counter*1, batch

counter, dual counter,

twin counter, and

tachometer (selectable)

Ratings

Power supply

voltage*2

• 100 to 240 VAC, 50/60 Hz

• 24 VAC, 50/60 Hz or 12 to 24 VDC

• 100 to 240 VAC, 50/60 Hz

•12 to 24 VDC

• 100 to 240 VAC at 50/

60 Hz

• 24 VAC at 50/60 Hz or

12 to 24 VDC

• 12 to 24 VDC

Operating volt-

age fluctuation

range

85% to 110% of rated supply voltage (12 to 24 VDC: 90% to 110%)

Power con-

sumption Approx. 9.4 VA at 100 to 240 VAC, Approx. 7.2 VA/4.7 W at 24 VAC/12 to 24 VDC, Approx. 3.7 W at 12 to 24 VDC

Mounting method Flush mounting or surface mounting Flush mounting

External connections 11-pin socket Screw terminals

Degree of protection IEC IP66, UL508 Type 4X (indoors) for panel surface only and only when Y92S-29 Waterproof Packing is used.

Input signals CP1, CP2, reset, and total reset CP1, CP2, reset 1, and reset 2

Counter

Maximum

counting speed 30 Hz (minimum pulse width: 16.7 ms) or 10 kHz (minimum pulse width: 0.05 ms) (selectable) (ON/OFF ratio 1:1) *Common setting for CP1 and CP2

Input mode Increment, decrement, increment/decrement (UP/DOWN A (command input), UP/DOWN B (individual inputs), or UP/DOWN C (quadrature inputs))

Output mode N, F, C, R, K-1, P, Q, A, K-2, D, and L. N, F, C, R, K-1, P, Q, A, K-2, D, L, and H.

One-shot out-

put time 0.01 to 99.99 s

Reset system External (minimum reset signal width: 1 ms or 20 ms, selectable), manual, and automatic reset (internal according to C, R, P, and Q mode operation)

Tachometer Refer to the separate table for tachometer function ratings.

Prescaling function Yes (0.001 to 9.999) Yes (0.001 to 99.999) Yes (0.001 to 9.999) Yes (0.001 to 99.999) Yes (0.001 to 9.999) Yes (0.001 to 99.999)

Decimal point adjustment Yes (rightmost 3 digits)

Sensor waiting time 290 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)

Input method

No-voltage inputs:

ON impedance: 1 kΩ max. (Leakage current: 12 mA at 0 Ω)

ON residual voltage: 3 V max.

OFF impedance: 100 kΩ min.

Voltage input:

High (logic) level: 4.5 to 30 VDC

Low (logic) level: 0 to 2 VDC (Input resistance: approx. 4.7 kΩ)

No-voltage input/voltage input (selectable)

External power supply 12 VDC (±10%), 100 mA (except for H7CX-A@D models) Refer to Precautions for Correct Use on page page 53 for details.

Control output • Contact output: 3 A at 250 VAC/30 VDC, resistive load (cosφ=1), Minimum applied load: 10 mA at 5 VDC (failure level: P, reference value)

• Transistor output: NPN open collector, 100 mA at 30 VDC, Residual voltage: 1.5 VDC max. (approx. 1 V), Leakage current: 0.1 mA max.

Display*3

7-segment, negative

transmissive LCD

Character height

Count value: 12 mm

(red)

Set value: 6 mm (green)

7-segment, negative

transmissive LCD

Character height

Count value: 10 mm

(red)

Set value: 6 mm (green)

7-segment, negative

transmissive LCD

Character height

Count value: 12 mm

(red, green, or orange

selectable)

Set value: 6 mm (green)

7-segment, negative

transmissive LCD

Character height

Count value: 10 mm

(red, green, or orange

selectable)

Set value: 6 mm (green)

7-segment, negative

transmissive LCD

Character height

Count value: 12 mm

(red, green, or orange

selectable)

Set value: 6 mm (green)

7-segment, negative

transmissive LCD

Character height

Count value: 10 mm

(red, green, or orange

selectable)

Set value: 6 mm (green)

Digits

4 digits

−999 to 9999

(−3 digits to +4 digits)

6 digits

−99999 to 999999

(−5 digits to +6 digits)

4 digits

−999 to 9999

(−3 digits to +4 digits)

6 digits

−99999 to 999999

(−5 digits to +6 digits)

4 digits

−999 to 9999

(−3 digits to +4 digits)

6 digits

−99999 to 999999

(−5 digits to +6 digits),

tachometer: 0 to 999999

Memory backup EEPROM (overwrites: 100,000 times min.) that can store data for 10 years min.

Operating temperature

range −10 to 55°C (−10 to 50°C if Counter/Tachometers are mounted side by side) (with no icing or condensation)

Storage temperature range −25 to 70°C (with no icing or condensation)

Operating humidity range 25% to 85%

Case color Black (N1.5) (Optional Front Panels are available to change the Front Panel color to light gray or white.)

Attachments --- Flush mounting adapter, waterproof packing, terminal cover

Flush mounting adapter,

waterproof packing,

terminal cover, label for

DIP switch settings

H7CX-A@-N

Tachometer Function Ratings

* An input OFF time of at least 20 ms is required.

Characteristics

Model

Item

H7CX-A114@-N

H7CX-A11@-N

H7CX-A4@-N

H7CX-A@-N

H7CX-A4W@-N

H7CX-AW@-N/-AU@-N

Input mode

No tachometer

functionality

Selectable from independent measurements for 1 or 2 inputs, differential input for 2 inputs, absolute ratio for 2 inputs, and error ratio

for 2 inputs.

Pulse measurement

method Periodic measurement Pulse width measurement

Maximum counting

speed

30 Hz

(minimum pulse width: 16.7 ms)

1-input mode:

10 kHz

(minimum pulse width: 0.05 ms)

Other modes:

5 kHz

(minimum pulse width: 0.1 ms)

30 Hz

(minimum pulse width: 16.7 ms)

1-input mode:

10 kHz

(minimum pulse width: 0.05 ms)

Other modes:

5 kHz

(minimum pulse width: 0.1 ms)

Minimum input

signal width --- --- 30 ms*1 1-input mode: 0.2 ms

Other modes: 0.4 ms*

Measuring ranges 0.001 to 30.00 Hz 1-input mode: 0.001 to 10 kHz,

Other modes: 0.01 to 5 kHz 0.030 to 999999 s 1-input mode: 0.0002 to 99999 s

Other modes: 0.0004 to 99999 s

Sampling period 200 ms min.

200 ms min. or continuous

selectable (minimum interval of

10 ms)

Continuous (minimum interval of 10 ms)

Measuring accuracy ±0.1% FS ±1 digit max. (at 23 ±5°C)

Output mode

Input mode:

Not 2-input independent measurement: HI-LO, AREA, HI-HI, LO-LO

2-input independent measurement: HI-HI, LO-LO

Auto-zero time 0.1 to 999.9s

Startup time 0.0 to 99.9s

Averaging Simple averaging/moving averaging selectable, Processing: OFF, 2, 4, 8, or 16 times

Hold input Minimum input signal width: 20 ms

* Refer to the Life-test Curve.

Applicable Standards

*1. The following safety standards apply to models with sockets (H7CX-A11@ or H7CX-A114@).

cUL (Listing): Applicable when an OMRON P2CF(-E) Socket is used.

cUR (Recognition): Applicable when any other socket is used.

*2. Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)

Insulation resistance 100 MΩ min. (at 500 VDC) between current-carrying terminals and exposed non-

current-carrying metal parts, and between non-continuous contacts

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-

current-carrying metal parts

2,000 VAC, 50/60 Hz for 1 min between power supply and input circuit for all models

except H7CX-@D@ (1,000 VAC for 24 VAC/12 to 24 VDC)

1,000 VAC (for H7CX-@SD@), 50/60 Hz for 1 min between control output, power

supply, and input circuit (2,000 VAC for models other than H7CX-@SD@)

1,000 VAC, 50/60 Hz for 1 min between non-continuous contacts

Impulse withstand voltage

3.0 kV between power terminals (1.0 kV for models with 24 VAC/12 to 24 VDC or 12

to 24 VDC)

4.5 kV between current-carrying terminals and exposed non-current-carrying metal

parts (1.5 kV for models with 24 VAC/12 to 24 VDC or 12 to 24 VDC)

Noise immunity

±1.5 kV between power terminals (±480 V for models with 12 to 24 VDC)

±600 V between input terminals

Square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)

Static immunity Malfunction: 8 kV

Destruction: 15 kV

Vibration

resistance

Destruction 10 to 55 Hz with 0.75-mm single amplitude each in three directions for 2 h each

Malfunction 10 to 55 Hz with 0.35-mm single amplitude each in three directions for 10 min each

Shock re-

sistance

Destruction 300 m/s2 each in three directions

Malfunction 100 m/s2 each in three directions

Life expectancy

Mechanical: 10,000,000 operations min.

Electrical: 100,000 operations min. (3 A at 250 VAC, resistive load, ambient

temperature condition: 23°C)*

Weight Approx. 130 g (Counter only)

Approved

safety

standards

cULus (or cURus): UL508/CSA C22.2 No. 14 *1

EN 61010-1 (IEC 61010-1): Pollution degree 2/overvoltage category II

B300 PILOT DUTY

1/4 HP 120 VAC, 1/3 HP, 240 VAC, 3 A resistive load

VDE0106/P100 (finger protection)

EMC

(EMI) EN61326-1 *2

Emission Enclosure: EN 55011 Group 1 class A

Emission AC mains: EN 55011 Group 1 class A

(EMS) EN61326-1 *2

Immunity ESD: EN 61000-4-2: 4 kV contact discharge;

8 kV air discharge

Immunity RF-interference: EN 61000-4-3:

10 V/m (Amplitude-modulated, 80 MHz to 1 GHz);

10 V/m (Pulse-modulated, 900 MHz ±5 MHz)

Immunity Conducted Disturbance: EN 61000-4-6: 10 V (0.15 to 80 MHz)

Immunity Burst: EN 61000-4-4: 2 kV power-line;

1 kV I/O signal-line

Immunity Surge: EN 61000-4-5: 1 kV line to lines (power and output lines);

2 kV line to ground (power and output lines)

Immunity Voltage Dip/Interruption: EN 61000-4-11: 0.5 cycle, 100% (rated voltage)

Life-test Curve (Reference

Values)

Resistive load

Inductive load

A current of 0.15 A max. can be switched at 125

VDC (cosφ=1) and current of 0.1 A max. can be

switched if L/R=7 ms. In both cases, a life of

100,000 operations can be expected.

1,000

700

500

300

100

Load current (A)

01 2 34

30 VDC (cosφ=1)

250 VAC (cosφ=1)

No. of operations (×103)

1,000

700

500

300

100

01 2 34

30 VDC (L/R=7 ms)

Load current (A)

250 VAC (cosφ=1)

No. of operations (×10

)

H7CX-A@-N

I/O Functions

Using as a Counter*1

*1. For information on operation of I/O functions, refer to pages page 22 to page 25.

*2. In increment mode or increment/decrement mode, the present value returns to 0; in decrement mode, the present value returns to the set value with 1-stage models,

and returns to set value 2 with 2-stage models.

*3. Reset operates as described in the following table. (The reset indicator will not be lit.)

• The following table shows the delay from when the reset signal is input until the output is turned OFF. (Reference values)

Operating Procedures (Tachometer Function)

Inputs

CP1, CP2

(1) In general (except for Dual Counter Mode)

• Reads counting signals.

• Increment, decrement, command, individual, and quadrature inputs accepted.

(2) When used as a dual counter or twin counter

• Reads CP1 count signals with CP1 input and CP2 count signals with CP2 input.

• Increment signals can be input.

Reset/reset 1

(1) In general (except for Dual Counter Mode)

• Resets present value and outputs (OUT2 when using the batch counter)*2.

• Counting cannot be performed during reset/reset 1 input.

• Reset indicator is lit while reset input is ON.

(2) When used as a dual counter or twin counter.

• Resets the CP1 present value (to 0).

• Counting for CP1 input cannot be performed while the reset 1 input is ON.

• The reset indicator is lit while the reset 1 input is ON.

Total reset or reset 2 The reset function depends on the selected configuration*3.

Outputs OUT1, OUT2 Outputs signals according to the specified output mode when a set value is reached.

Configuration Reset operation

1-stage/2-stage

preset counter Does not operate (not used).

Total and preset

counter

• Resets the total count value.

• The total count value is held at 0 while the total reset input is ON.

Batch counter • Resets the batch count value and batch output (OUT1).

• The batch count value is held at 0 while the reset 2 input is ON.

Dual counter • Resets the CP2 present value.

• Counting for CP2 input cannot be performed while the reset 2 input is ON.

Twin counter • Resets the CP2 present value.

Minimum reset signal width Output delay time

1 ms 0.8 to 1.2 ms

20 ms 15 to 25 ms

Inputs

CP1, CP2 Reads counting signals. (The CP2 input can be used when the input mode is not 1-input mode.)

Reset/reset 1

• Holds the measurement value and outputs. (The reset 2 input can be used when the input mode

is 2-input independent measurement.)

• Functions as a hold input.

The measurement value (displayed value) and the outputs are held while the RST Key on the

front panel is pressed.

• The reset indicator is lit when the value is being held.

Outputs OUT1, OUT2 Outputs signals according to the specified output mode when a set value is reached.

H7CX-A@-N

Connections

Terminal Arrangement

Confirm that the power supply meets specifications before use.

Transistor Output

• The transistor output of the H7CX is isolated from the internal

circuitry by a photocoupler, so the transistor output can be used as

both NPN and PNP output.

• The diode connected to the collector of the output transistor is used

to absorb inverted voltage that is generated when an inductive load

is connected to the H7CX.

H7CX-A-N/-A4-N H7CX-AD-N/-A4D-N H7CX-AS-N/-A4S-N

1-stage Contact Output 1-stage Contact Output

Terminals 1 and 6 are connected internally.

1-stage Transistor Output

H7CX-ASD-N/-A4SD-N H7CX-AW-N/-A4W-N/-AWD1-N/-AU-N/-AUD1-N H7CX-AWS-N/-AWSD1-N/-AUSD1-N

1-stage Transistor Output

Terminals 1 and 6 are connected internally.

2-stage Contact Output 2-stage Transistor Output

H7CX-AWSD-N/-A4WSD-N H7CX-A11-N/-A114-N/-A11D1-N/-A114D1-N H7CX-A11S-N/-A114S-N/-A11SD1-N

2-stage Transistor Output

Terminals 1 and 6 are connected internally.

1-stage Contact Output 1-stage Transistor Output

678910

OUT

(−)

(+)

0 V

12345

Reset

Total reset

CP2

CP1

Sensor

12 VDC

External

power supply

678910

OUT

(+)

(−)

0 V

12345

Reset

Total reset

CP2

CP1

678910

12345

OUT

0 V

(−)

(+)

Reset

Total reset

CP2

CP1

Sensor

12 VDC

External

power supply

678910

0 V

12345

OUT

(+)(−)

Reset

CP2

CP1

Total reset

678910

11 12 13 OUT1

12345

OUT2

(+)(−)

0 V

(−)

(+)

Reset 1

CP2

CP1

12 VDC

External

power supply

Reset 2

Sensor

12 13

1: “-AU@” Models

678910

11 12 13

12345

OUT1

OUT2

0 V

(+)(−)

(−)

(+)

Reset 1

CP2

CP1

Sensor

12 VDC

External

power supply

Reset 2

678910

12 13

0 V

12345

OUT1

OUT2

(+)(−)

Reset 1

CP2

CP1

Reset 2

(+)(−)

OUT

0 V

(−)

(+)

Reset

Total reset

CP2

CP1

Sensor

12 VDC

External

power supply

Internal circuit

0 V

OUT

(+)(−)

(−)

(+)

Reset

Total reset

CP2

CP1

Sensor

12 VDC

External

power supply

Internal circuit

Power for load

Load

Power for load

Load

NPN Output PNP Output

Power for load

Counter

Inductive

load

H7CX-A@-N

Block Diagram

Note: All models except for H7CX-@D-N have basic insulation.

Input Circuits

CP1, CP2, Reset/Reset 1, and Total Reset/Reset 2

Input

Input Connections

The inputs of the H7CX-@-N are no-voltage (short-circuit or open) inputs or voltage inputs.

No-voltage Inputs (NPN Inputs)

No-voltage Input Signal Levels

Note: The DC voltage must be 30 VDC max.

Voltage Inputs (PNP Inputs)

Voltage Input Signal Levels

Note: 1. The DC voltage must be 30 VDC max.

2. Input resistance: Approx. 4.7 kΩ

Output circuit

(See note.)

Display circuit

Input circuits

(Basic insulation)

Internal

control circuit

Power supply

circuit

Key switch

circuit

No-voltage Inputs

(NPN Inputs)

Voltage Inputs (PNP Inputs)

Internal

circuit

+14V

1 kΩ

Approx. 4.7 kΩInternal

circuit

Open Collector Voltage Output Contact Input DC Two-wire Sensor

H7CX-A@

H7CX-A11@

Note: Operates with transistor ON.

PLC or

sensor

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

H7CX-A@

H7CX-A11@

Note: Operates with transistor ON.

Sensor

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

Note: Operates with relay ON.

H7CX-A@

H7CX-A11@

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

Note: Operates with transistor ON.

H7CX-A@

H7CX-A11@

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

No-contact input

Short-circuit level (transistor ON)

• Residual voltage: 3 V max.

• Impedance when ON: 1 kΩ max.

(The leakage current is approx. 12 mA when the impedance is 0 Ω.)

Open level (transistor OFF)

• Impedance when OFF: 100 kΩ min.

Contact input Use contacts which can adequately switch 5 mA at 10 V.

Applicable Two-wire Sensor

• Leakage current: 1.5 mA max.

• Switching capacity: 5 mA min.

• Residual voltage: 3 VDC max.

• Operating voltage: 10 VDC

No-contact Input (NPN Transistor) No-contact Input (PNP Transistor) Contact Input

Note: Operates with transistor OFF.

H7CX-A@

H7CX-A11@

Sensor

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

Note: Operates with transistor ON.

H7CX-A@

H7CX-A11@

Sensor

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

Note: Operates with relay ON.

H7CX-A@

H7CX-A11@

678910

37564

0 V for inputs

Reset/reset 1 input

CP2 input

CP1 input

Total reset/reset 2 input

High level (input ON): 4.5 to 30 VDC

Low level (input OFF): 0 to 2 VDC

H7CX-A@-N

Nomenclature

Dimensions (Unit: mm)

Counters

(Enable)

(Default setting) OFF

(Disable)

RST

1st digit4th digit

1st digit6th digit

1 4

1 2

Display Section

3. Reset Indicator (orange)

1. Key Protect Indicator (orange)

2. Control Output Indicator (orange)

4. Total Count Indicator

6. Set Value 1, 2 Stage Indicator

8. Set value (Sub-display)

(Character height: 6 mm, green)

9. Hold Display (orange)

OUT: (One-stage)

OUT: (Two-stage)

(Lit when the total count value is displayed.)

(Lit when the reset input (1) or Reset Key is ON.)

Displayed only when the configuration selection

mode is not tachometer mode.

5. Batch Indicator

(Lit when the batch count value is displayed.)

Operation Keys

10. Mode Key

(Changes modes and setting items.)

11. Reset Key (See note.)

12. Up Keys to

1 6

(6-digit models: to )

13. Down Keys to

Switches

14. Key-protect Switch

15. DIP Switch

7. Present Value (Main Display)

(Character height: 12 mm (6-digit: 10 mm), red*)

(Front view of 4-digit model)

(Front view of 6-digit model)

* Characters on models with screw terminals (H7CX-A11@)

can be switched between red, green, and orange.

Displayed only when the configuration selection

mode is not tachometer mode.

OFF

12345678

Note: The reset functions depends on the selected configuration.

Configuration Reset operation

1-stage/2-stage

preset counter Resets the present value and outputs.

Total and preset

counter

• Resets the present value and outputs.

• When the total count value is displayed, resets the

present value, the total count value, and outputs.

Batch counter

• Resets the present value and OUT2.

• When the batch count value is displayed, resets the

present value, the batch count value, and outputs.

Dual counter Resets the CP1 present value, CP2 present value, dual

count value, and outputs.

Twin counter

Resets the CP1 present value and output 1 when the

CP1 present value is displayed.

Resets the CP2 present value and output 2 when the

CP2 present value is displayed.

Tachometer

Holds the measurement value and outputs (hold

function).

(When the input mode is 2-input independent

measurement, the CP1 measurement value display will

hold the CP1 measurement value and output 1 and the

CP2 measurement value display will hold the CP2

measurement value and output 2.)

14 15

Model with 4 Digits

6 mm

12 mm

Character Size

for Sub-display

Character Size

for Main Display

Model with 6 Digits

10 mm 6 mm

Character Size

for Sub-display

Character Size

for Main Display

44.8 × 44.8

48 × 48 6

H7CX-A-N/-AS-N/-AW-N/-AWS-N/-AWD1-N/-AWSD1-N/-A4-N/-A4S-N/-A4W-N/-AU-N/-AUD1-N/-AUSD1-N

(Flush Mounting Models)

Note: M3.5 terminal screw (effective length: 6 mm)

H7CX-A@-N

Dimensions with Flush Mounting Adapter

48 × 48

44.8 × 44.8

H7CX-AD-N/-ASD-N/-AWSD-N/-A4D-N/-A4SD-N/-A4WSD-N (Flush Mounting Models)

Note: M3.5 terminal screw (effective length: 6 mm)

48 × 48

44.8 × 44.8

63.7 14.4

H7CX-A11-N/-A11S-N/-A11D1-N/-A11SD1-N/-A114-N/-A114S-N/-A114D1-N (Flush Mounting/Surface Mounting Models)

48 76.57.5

Panel Y92F-30 (provided)

Flush Mounting Adapter

Y92S-29 (provided)

Waterproof Packing

(51)

H7CX-A-N/-AS-N/-AW-N/-AWS-N/-AWD1-N/-AWSD1-N/-A4-N/-A4S-N/-A4W-N

(Provided with Adapter and Waterproof Packing)

Panel Cutouts

Panel cutouts are as shown below. (according

to DIN43700).

Note: 1. The mounting panel thickness

should be 1 to 5 mm.

To allow easier operation, it is

recommended that Adapters be mounted

so that the gap between sides with hooks

is at least 15 mm (i.e., with the panel

cutouts separated by at least 60 mm).

It is possible to horizontally mount

Timers side by side. Attach the Flush

Mounting Adapters so that the surfaces

without hooks are on the sides of the

Timers. If they are mounted side-by-

side, water-resistance will be lost.

Dimensions with Front

Connecting Socket

* These dimensions depend on the kind of DIN Track.

(Reference value)

60 min.

15 min.

+0.6

With Y92A-48F1 attached.

With Y92A-48 attached.

A=(48n−2.5) +1

−0

A=(51n−5.5) +1

−0

A={48n−2.5+(n−1)×4} +1

−0

n Units mounted

side by side

103.2* 100.9

H7CX

-A11@

P2CF-11(-E) Front Connecting Socket

(order separately)

(51)

7.5 57.5

Panel Y92F-30 (provided)

Flush Mounting Adapter

Y92S-29 (provided)

Waterproof Packing

H7CX-AD-N/-ASD-N/-AWSD-N/-A4D-N/-A4SD-N/-A4WSD-N

(Provided with Adapter and Waterproof Packing)

(51)

7.5 89.9

Panel

P3GA-11 (order separately)

Back-connecting Socket

Y92F-30 (order separately)

Flush Mounting Adapter

Y92

-29 (order separately)

Waterproof Packing

H7CX-A11-N/-A11S-N/-A11D1-N/-A11SD1-N/-A114-N/-A114S-N/-A114D1-N

(Adapter and Waterproof Packing Ordered Separately)

H7CX-A@-N

Accessories (Order Separately)

Front Panel (Replacement Part)

You can change the color of the Front Panel when mounting the

Counter/Tachometer. The Counter/Tachometer is shipped with a

black (N1.5) Front Panel. "COUNTER" is printed on the front of

Replacement Front Panels.

Protecting the Counter/Tachometer in Environments

Subject to Oil

The Waterproof Packing will deteriorate, harden, and shrink

depending on the application environment. To ensure maintaining the

IP@6, UL Type 4X waterproof level, periodically replace the

Waterproof Packing. The periodic replacement period will depend on

the application environment. You must confirm the proper

replacement period. Use 1 year or less as a guideline. If the

Waterproof Packing is not replaced periodically, the waterproof level

will not be maintained. It is not necessary to mount the Waterproof

Packing if waterproof construction is not required.

Note: Depending on the operating environment, the condition

of resin products may deteriorate, and may shrink or

become harder. Therefore, it is recommended that resin

products are replaced regularly.

Y92P-CXC4G

4-digit Counter

Light gray (5Y7/1)

Y92P-CXC4S

4-digit Counter

White (5Y9.2/0.5)

Y92P-CXT4B

4-digit Counter

Black (N1.5)

Replacement Method

The Front Panel is attached to the

Counter/Tachometer with tabs in

four locations. To remove the

Front Panel, open the tabs and

pull the Front Panel forward. To

attach the Front Panel, press it

onto the Counter/Tachometer so

that all four tabs lodge into the

grooves on the body of the

Counter/Tachometer.

Ta b s

Grooves

Y92P-CXT6G

6-digit Counter

Light gray (5Y7/1)

Y92P-CXT6S

6-digit Counter

White (5Y9.2/0.5)

Y92P-CXT6B

6-digit Counter

Black (N1.5)

The H7CX's panel surface is water-resistive (conforming to IP@6,

UL Type 4X) and so even if drops of water penetrate the gaps

between the keys, there will be no adverse effect on internal circuits.

If, however, there is a possibility of oil being present on the

operator's hands, use the Soft Cover. The Soft Cover ensures

protection equivalent to IP54F against oil. Do not, however, use the

H7CX in locations where it would come in direct contact with oil.

Soft Cover

Y92A-48F1

Hard Cover

Y92A-48

Y92F-45

Use this Adapter to

install the Counter/

Tachometer in a

cutout previously

made for a DIN 72

× 72 mm device

(panel cutout: 68 ×

68 mm).

Flush Mounting Adapter

Y92F-30

Order the Flush

Mounting Adapter with

the following model

number separately if it

is lost or damaged.

Note: The

Waterproof

Packing is

included with

models with

screw

terminals.

Waterproof Packing

Y92S-29

Note: The

Waterproof

Packing is

included with

models with

screw

terminals.

Order the Waterproof Packing

separately if it is lost or damaged. The

Waterproof Packing can be used to

achieve IP66 protection.

H7CX-A@-N

Connection Sockets

Front Connecting Socket

Note: Round crimp terminals cannot be used on Finger-safe Sockets. Use forked crimp terminals.

Back-connecting Sockets

Note: A Y92A-48G Terminal Cover can be used with the Socket to create a finger-safe construction.

Terminal Covers for P3GA-11 Back-connecting Socket

Note: The Terminal Cover can be used with a Back-mounting Socket (P3GA-11) to create a finger-safe construction.

Model Dimensions Terminal arrangement

and internal connections

Mounting hole

dimensions

P2CF-11

(Top View)

Note: The Socket can

also be mounted

to DIN track.

P2CF-11-E

(Finger-safe Type)

Model Dimensions Terminal arrangement

and internal connections

P3GA-11

(Bottom View)

Model Dimensions

Y92A-48G

70 max.

50 max.

Two, 4.5-dia. holes

Eleven, M3.5 × 7.5 sems screws 7.8

31.2 max.

8 7 6 5

10 11 1 2

9 3

40±0.2

Two, M4 or 4.5-dia. holes

10 11

7865

P2CF-11-E

10A250VAC

RESISTIVE

±0.2

7.8

4.5

35.4

1.2

70 max.

50 max.

Two, 4.5-dia. holes

Eleven, M3.5 × 7.5 set screws

31.2 max.

27 dia.

4.5 16.3 6.2

25.6

876

101112

Y92A-48G UP

P C

Twelve, 6.4-dia. holes

47.7 × 47.7

48 × 48

27.6

24.6

16.5

47.4

H7CX-A@-N

Optional Products for Track Mounting

Note: Order Spacers in increments of 10.

±0.3

7.3

±0.15

4.5

15 25 2510 15 (5)*

1025 25

1,000 (500)* * The values shown in parentheses

are for the PFP-50N.

Mounting Track

PFP-100N

PFP-50N

15 25 25 1,000

4.5

25 25 1510 1

242735±0.3

1.5

29.2

Mounting Track

PFP-100N2

4.8

1.3

35.5 35.3

1.8

6.2

M4 spring washer

11.5

M4 × 8

pan head

screw

End Plate

PFP-M

44.3 34.8

16.5

Spacer

PFP-S

H7CX-A@-N

Counter

Operating Procedures

Setting Procedure Guide

Setting for Counter Operation *

Use the following settings.

Setting for Tachometer Operation *

Refer to page page 27.

* At the time of delivery, the H7CX is set to the 1-stage preset counter configuration. (2-stage models are set to the 2-stage preset counter configuration.) Refer to page page 35 for information

on switching models.

I/O Functions for Counter Operation

After making DIP switch settings for basic operations, advanced functions can be added using the operation keys.

For details, refer to page page 16.

Key-protect switch

Disabled Enabled

OFF

K-1

UP DOWN

Refer to the table on the right.

30 Hz 5 kHz

20 ms 1 ms

DIP switch settings

Counting speed

Input mode

Output mode

Minimum reset signal

Input selection

Output time 0.5 s 0.05 s

NPN PNP

Note: All pins are factory-set to OFF.

• When setting functions using the DIP switch, be sure to set pin 1 of the DIP switch to ON.

• DIP switch settings are effective when the power is turned ON again. (Perform DIP switch settings while the power is OFF.)

Step1

Step3

Set the basic parameters.

(If the desired I/O mode is not listed below or to set all parameters using the front panel keys, perform ,

below.)

Note: can be performed first, followed by .

Note: The configuration that can be selected depends on the model.

* The default mode is 1-stage preset counter configuration (2-stage preset counter configuration for 2-stage models).

Item OFF ON

Output modePin 5Pin 4

Step2

Step2 Step1

Hold down for 1 s min.

Select the function from Table 1 using the U (D) Key.

Run mode

Power ON

Hold down for 1 s min.

+twn

The H7CX-A@-N is a Counter that contains more than one functional counter.

When using the Counter in any mode other than the default mode*, use the following chart to enter

Configuration Selection Mode and set the functions that are suitable to the application.

(1-stage

preset

counter)

(2-stage

preset

counter)

(Total and

preset counter)

(Batch

counter)

(Dual

counter)

(Twin

counter)

(Tachometer)

Configuration

selection mode

Be sure to set pin 1 to ON.

OFF

12345678

H7CX-A@-N

Counter

Run mode

Power ON

Function

setting mode

*5 Displayed for output modes other than K-2, D, L, and H only.

*6 Displayed only when the input mode is ud-a, ud-b, or ud-c.

(Not displayed when the function is set to twn.)

* The display shows 5 kHz, but the maximum

counting speed is 10 kHz.

Note: Displayed only when the output mode is C, R, K-1, P, Q, A,

or K-2.

Note: Displayed for terminal-block models (except H7CX-A11@) only.

*3 When Using Dual Counter

Operation

Usage as a Decrementing Counter (5ub)

The 5ub parameter is normally not

displayed. You must set the outm

parameter shown below in advance to *6

(k-2, d, l, or h) to display it.

*7 Set each digit using the individual U (D) Keys.

Note: Displayed only when the

output mode is C, R, K-1, P, Q,

A, or K-2.

Note: Displayed for output modes

other than D, L, and H.

HOLD cannot be set when

the output mode is K-2.

*7 Set each digit using the individual U (D) Keys.

Note: Displayed only when Twin Counter Mode is not selected.

(Red) (Green) (Orange)

(Red-green) (Green-red) (Red-orange) (Orange-red)

(Green-orange) (Orange-green)

3 s min.*2

3 s min.*1

Step3

Parameters that cannot be set with the DIP switch are set with the operation keys on the front panel.

Change to Function Setting Mode.

Input mode

(CNTM)

Output

time

(OTIM)

Output mode

(OUTM)

NPN/PNP

input mode

(IMOD)

Display color

(COLR)

(1 ms)(20 ms)

(No decimal point)

Prescale

value

(PSCL)

Counting

speed

(CNTS)

(30 Hz) (5 kHz)

(PNP input)(NPN input)

The characters displayed in reverse video are the default settings.

When performing settings with operation keys only, set pin1 of the DIP switch to OFF (factory setting).

If pin 1 of the DIP switch is set to ON, the setting items indicated by will not be displayed.

For 6-digit models, only U Keys are provided.

Displays for 6-digit models are given in parentheses.

(N)

(0.50 s) (99.99 s)(0.01 s)

(0.01 s) (99.99 s)

(Outputs held)

(F) (C) (R) (K-1) (P) (Q) (A) (K-2) (D) (L) (H)

*6 *6 *6 *6

(DOWN) (

UP/DOWN A

)(

UP/DOWN B

)(

UP/DOWN C

)(UP)

(99.999)(1.000)(0.001)

(0.50 s) (99.99 s)(0.01 s)

To next pageFrom next page

(Addition) (Subtraction)

Reset input

signal width

(IFLT)

Decimal

point position

(DP)

• Set the input mode using the U (D) Keys.

• Set the output mode using the U (D) Keys.

• Set each digit using the individual U (D) Keys.

• Set the counting speed using the U (D) Keys.

• Set the Reset input signal width using the U (D) Keys.

• Set the decimal point position using the U (D) Keys.

(One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

• Set each digit using the individual U (D) Keys.

(9.999)

• Set the NPN/PNP input mode using the U (D) Keys.

• Set the display color using the U (D) Keys.

Dual count

calculating

mode

(ADD)

• Set the dual count calculating

mode using the UD Keys.

*4 Displayed only when the output mode is K-2,

D, L, or H.

When using as a 2-stage preset counter

One-shot

output 2

time

(OTM2)

One-shot

output 1

time

(OTM1)

Note: Displayed only when the

output mode is C, R, K-1, P, Q,

A, or K-2.

(0.50 s) (99.99 s)(0.01 s)

When using as a batch counter

One-shot

output 2

time

(OTM2)

Function Setting Mode

grnred org r-g g-r r-o o-r g-o o-g

up down

0.01 99.990.50

30hz

1ms

0.001 99.9999.999

1.000

pnpnpn

20ms

crk-1 k-2pqa dlh

subadd

0.50

hold 0.01 99.99

0.01 0.50 99.99

0.01 99.99

ud-a ud-b ud-c

*1 If the mode is switched to the function setting mode during operation, operation will continue.

Changes made to settings in function setting mode are enabled for the first time when the mode is changed to run mode. Also,

when settings are changed, the counter is reset (present value initialized and output turned OFF) on returning to run mode.

If the output time is 0.00, hold is displayed.

Note: Displayed only when the

output mode is C, R, K-1, P,

Q, or A.

Note: Displayed only when the

output mode is C, R, K-1, P,

Q, or A.

(0.50 s) (99.99 s)(0.01 s)

Twin Counter

Output 2

output

time

(OTM2)

Output 1

output

time

(OTM1)

0.500.01 99.99

(0.50 s) (99.99 s)(0.01 s)

0.500.01 99.99

For details on operations and display in run mode, refer to page page 20.

The display depends on the selected configuration.

H7CX-A@-N

Counter

(9999 × 1000 times)(0 × 1000 times)

(OFST)(ABS)

(KP-1) (KP-2) (KP-3) (KP-4) (KP-5) (KP-6) (KP-7)

(9999 × 1000 times)(0 × 1000 times)

99990

(9999)(1)

99991

(9999)(1)

99991

(9999)(1)

99991

ofstabs

kp-1 kp-2 kp-3 kp-4 kp-5 kp-6 kp-7

(ON)(OFF)

onoff

Note: 1 to 999999 for 6-digit models

*8 Set each digit using the individual U (D) Keys.

Note: The monitor value is only displayed. It cannot be set.

Forecast

setting

upper limit

(PL-H)

Key protect

level

(KYPT)

From previous

page

To previous

page

Output ON

count alarm set

value/monitor

value

• Make the absolute value setting and forecast setting using the U (D) Keys.

• Set each digit using the individual U (D) Keys.

• Set the key protect level using the U (D) Keys.

Procedure for Models Other than “-@W@” Models

Output

ON count

alarm set

value

Output

ON count

monitor

value

Output 1

(OUT1) ON

count alarm

set value

Function Setting Mode

Absolute value

setting/forecast

value setting

(SETM)

Set value

upper limit

(SL-H)

Note: 1 to 999999 for 6-digit models.

Note: Displayed only when the output mode is set to bcnt.

• Set each digit using the individual U (D) Keys.

Procedure for “-@W@” Models

Note: The monitor value is only displayed. It cannot be set.

Output 2

(OUT2) ON

count alarm

set value

Output 1

(OUT1) ON

count monitor

value

Output 2

(OUT2) ON

count monitor

value

Batch count

upper limit

(BL-H)

Note: Displayed only when the configuration selection mode is set to the 2-stage function 2cnt.

Note: Displayed only when the configuration selection mode is set to the 2-stage function 2cnt and a forecast value is set.

Output

allocation

change

Note: Displayed only for "-AU@" models.

off: Output 1 = 12, 13, Output 2 = 3, 4, 5 on: Output 1 = 3, 4, 5, Output 2 = 12, 13

The numbers are the terminals numbers.

H7CX-A@-N

Counter

Explanation of Functions

Items marked with stars ★ can be set using the DIP switch.

Input Mode (cntm)★

Set increment mode (UP), decrement mode (DOWN), or one of the

increment/decrement modes (UP/DOWN A, UP/DOWN B, or UP/

DOWN C) as the input mode.

Input modes other than UP or DOWN modes cannot be set using the

DIP switch and so use the operation keys if other modes are required.

(For details on the operation of the input modes, refer to Input Modes

and Present Value on page page 21.)

Dual Count Calculating Mode ( calm)

When using as a dual counter, select either ADD (addition) or SUB

(subtraction) as the calculation method for the dual count value.

ADD: Dual count value = CP1 PV + CP2 PV

SUB: Dual count value = CP1 PV − CP2 PV

Output Mode (outm)★

Set the way that control output for the present value is output. The

possible settings are N, F, C, R, K-1, P, Q, A, K-2, D, L, and H.

Output modes other than N, F, C, or K-1 cannot be set using the DIP

switch and so use the operation keys if other modes are required. The

output modes that can be set vary with the model.

(For details on the operation of the output modes, refer to Input/

Output Mode Settings on page page 22.)

One-shot Output Time (otim)★

Set the one-shot output time (0.01 to 99.99 s) for control output.

One-shot output can be used only when C, R, K-1, P, Q, A, or K-2 is

selected as the output mode. Output times other than 0.5 s or 0.05 s

cannot be set with the DIP switch and so use the operation keys if

other settings are required.

One-shot Output 2 Time (otm2)★

Set the one-shot output time (0.01 to 99.99 s) for control output

(OUT2).

One-shot output can be used only when C, R, K-1, P, Q, A, or K-2 is

selected as the output mode. Output times other than 0.5 s or 0.05 s

cannot be set with the DIP switch and so use the operation keys if

other settings are required.

One-shot Output 1 Time (otm1)

Set the one-shot output time (0.01 to 99.99 s) for control output

(OUT1).

One-shot output can be used only when D, L, or H is selected as the

output mode.

If the output time is set to 0.00, hold is displayed, and outputs are

held.

Counting Speed (cnts)★

Set the maximum counting speed (30 Hz/5 kHz) for CP1 and CP2

inputs together.

If contacts are used for input signals, set the counting speed to 30 Hz.

Processing to eliminate chattering is performed for this setting.

Reset Input Signal Width (iflt)★

Set the reset input signal width (20 ms/1 ms) for reset/reset 1 and total

reset/reset 2 inputs together.

If contacts are used for the input signal, set the input signal width to

20 ms. Processing to eliminate chattering is performed for this setting.

Decimal Point Position (dp)

Decide the decimal point position for the present value, CP1/CP2

present values, set value (SV1, SV2), total count value, and dual

count set value.

Prescale Value (pscl)

Pulses input to the counter are converted according to the specified

prescale value.

(Setting range: 0.001 to 99.999 for 6-digit models and 0.001 to 9.999

for 4-digit models.)

Example: To display the feed distance for systems that output 25

pulses for a feed length of 0.5 m in the form @@.@@ m:

1. Set the decimal point position to 2 decimal places.

2. Set the prescale value to 0.02 (0.5 ÷ 25).

• Observe the following points when setting a prescale value.

Set the set value to a value less than {Maximum countable value

− Prescale value}.

Example: If the prescale value is 1.25 and the counting range is

0.000 to 999.999, set the set value to a value less than 998.749

(= 999.999 − 1.25).

If the set value is set to a value greater than this, output will not turn

ON.

• Output will turn ON, however, if a present value overflow occurs

(FFFFFF or FFFF).

NPN/PNP Input Mode (imod)

Select either NPN input (no-voltage input) or PNP input (voltage

input) as the input format. When using a two-wire sensor, select NPN

input.

The same setting is used for all external inputs.

For details on input connections, refer to Input Connections on page

page 9.

Display Color (colr) (Displayed for terminal block models

(except H7CX-A11@) only.)

Set the color used for the present value.

* Output 2 for 2-stage models.

With the twin counter, output 1 and output 2 will both turn OFF when

the output status is OFF. Either output 1 or output 2 will turn ON when

the output status is ON.

Output OFF* Output ON*

red Red (fixed)

grn Green (fixed)

org Orange (fixed)

r-g Red Green

g-r Green Red

r-o Red Orange

o-r Orange Red

g-o Green Orange

o-g Orange Green

25 pulses

Encoder

0.5 m

Note: If the prescale value setting is incorrect, a counting error will

occur. Check that the settings are correct before using this

function.

H7CX-A@-N

Counter

Absolute Value Setting/Forecast Value Setting (setm)

For the 2 count output mode, an absolute value setting (abs) or

forecast value setting (ofst) can be set for set value 1.

When a forecast value is set, specify the forecast value set value (i.e.,

the deviation for the set value).

The forecast output (output 1) turns ON when the present value

reaches the forecast value.

If the forecast set value is greater than or equal to the set value, the

forecast output (output 1) will turn ON as soon as counting starts.

If the forecast value setting is used, specify the set value 2 minus the

forecast value setting for set value 1.

Set Value Upper Limit (sl-h)

Set the upper limit for the set value when it is set in run mode.

The setting can be made from 1 to 9999 for 4-digit models and from

1 to 999999 for 6-digit models.

Forecast Set Upper Limit (pl-h)

Set the upper limit for the forecast set value.

The setting can be made from 1 to 9999 for 4-digit models and from

1 to 999999 for 6-digit models.

Batch Count Upper Limit (bl-h)

Set the upper limit for the batch count value. The setting can be made

from 1 to 9999 for 4-digit models and from 1 to 999999 for 6-digit

models.

Output Allocation (otst)

When using an H7CX-AU@-N model as a 2-stage counter, the output

can be flexibly allocated to either stage 1 or 2.

The transistor output can be allocated to SV1 and the contact output

to SV2 or vice verse, as in the following tables.

H7CX-AU-N/-AUD1-N

H7CX-AUSD1-N

Key Protect Level (kypt)

Set the key protect level.

Refer to Key Protect Level on page page 36.

Output ON Count Alarm Set Value (on-a)

Set the alarm value for the output ON count.

The limit can be set to between 0 × 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of the output exceeds the alarm set value, e3

will be displayed on the Timer to indicate that the output ON count

alarm value was exceeded. Refer to Self-diagnostic Function on page

page 36 for information on the e3 display.

ON Count Alarm Set Values for Outputs 1 and 2 (OUT1

and OUT2) (on1a and on2a)

Set the ON count alarm values for the outputs 1 and 2.

The limit can be set to between 0 × 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of instantaneous output 1 or 2 exceeds the alarm

set value, e3 will be displayed on the Timer to indicate that the output

ON count alarm value was exceeded. Refer to Self-diagnostic

Function on page page 36 for information on the e3 display.

Output ON Count Monitor Value (on-c)

The monitor value is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

ON Count Monitor Values for Outputs 1 and 2 (OUT1 and

OUT2) (on1c and on2c)

The monitor value for output 1 or 2 is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

Output 1 Output 2

off Transistor (12-13) Contact (3, 4, 5)

on Contact (3, 4, 5) Transistor (12-13)

Output 1 Output 2

off Transistor (12-13) Transistor with diode (3, 4, 5)

on Transistor with diode (3, 4, 5) Transistor (12-13)

Set value 2

Set value 1

Control output 1 (OUT1)

Control output 2 (OUT2)

Count value

Example: F Mode

Set value

Forecast

value

Forecast set value

Forecast output (OUT1)

Control output (OUT 2)

Count value

Example: F Mode

H7CX-A@-N

Counter

Operation in Run Mode

I/O Functions for Counter Operation

Present value

Set value 1

Present value

Set value

Present value

Set value 2

Present value

Set value

Batch count value

Batch count set value

Present value 1

Set value 1

Present value 2

Set value 2

Present value

Set value

Total count value

Dual count value

Dual count

set value

CP1 present value

CP2 present value

Present value

Set value

Present value

Forecast Set Value

Total and Preset Counter

Batch Counter

Dual Counter

Twin Counter

• Set values for each digit as required using the U (D) Keys. (U Key only for 6-digit models.)

1-stage Preset Counter

2-stage Preset Counter with

Absolute Value Setting

• Present Value

Shows the present count value.

• Set Values (Set Value 1 and Set Value 2)

Set the set values.

When the present value reaches the set value (set

value 1 or set value 2), a signal is output according

to the specified output mode.

• Present Value/Set Value

Same as 1-stage preset counter.

• Total Count Value

Shows the present total count value.

• Present Value/Set Value

Same as 1-stage preset counter.

• Batch Count Value

Shows the number of times the count has been

completed for the present value.

• Batch Count Set Value

Set the batch count set value.

When the batch count value reaches the batch

count set value, batch output (OUT1) turns ON.

• Dual Count Value

Shows the sum of the CP1 present value and

CP2 present value when the dual count

calculating mode is ADD and shows the value

obtained by subtracting the CP2 present

value from the CP1 present value when the

dual count calculating mode is SUB.

• Dual Count Set Value

Set the dual count set value.

When the dual count value reaches the dual

count set value, signals are output according

to the specified output mode.

• CP1/CP2 Present Value

Show the present count values for CP1 and

CP2 present values respectively.

• Present Values 1 and 2

Shows the present count value 1 or 2.

• Set Values 1 and 2

Setting for present value 1 or 2.

• Present Value

Shows the present count value.

• Set Values

Set the set values.

• Forecast Set Value

Set the deviation for the set value.

2-stage Preset Counter with

Forecast Value Setting

H7CX-A@-N

Counter

Input Modes and Present Value (See note 1.)

I/O Functions for Counter Operation

UP (Increment) Mode DOWN (Decrement) Mode

CP1: Count input; CP2: Prohibit (gate) input

must be greater than the minimum signal width. (See note 2.)

CP1: Count input; CP2: Prohibit (gate) input

must be greater than the minimum signal width. (See note 2.)

CP1: Prohibit (gate) input; CP2: Count input

must be greater than the minimum signal width. (See note 2.)

CP1: Prohibit (gate) input; CP2: Count input

must be greater than the minimum signal width. (See note 2.)

* Counting starts when the CP1 is turned ON after turning ON the power.

UP/DOWN A Command Input Mode UP/DOWN B Individual Input Mode

must be greater than the minimum signal width. (See note 2.)

UP/DOWN C Quadrature Input Mode Note: 1. If the configuration selection is set to dual counter, CP1 and

CP2 input will operate in the same way as the count input

(CP1) of UP (increment) mode.

2. must be greater than the minimum signal width and

must be at least 1/2 the minimum signal width.

If they are less, a count error of ±1 may occur.

Minimum signal width: 16.7 ms (when maximum counting speed = 30 Hz)

100 μs (when maximum counting speed = 5 kHz)

3. The meaning of the H and L symbols in the tables is explained

below.

must be at least 1/2 the minimum signal width. (See note 2.)

CP1

CP2

Present value

Prohibit

A A

CP1

CP2

Present value

n−1

n−2

n−4

n−3

n−5

A A

Prohibit

*CP1

CP2

Present value

A A

Prohibit

*CP1

CP2

Present value

n−1

n−2

n−4

n−3

n−5

A A

Prohibit

CP1

CP2

Present value

A A

CP1

CP2

Present value

Symbol

Input method

No-voltage input

(NPN input)

Voltage input (PNP

input)

HShort-circuit 4.5 to 30 VDC

LOpen 0 to 2 VDC

CP1

CP2

Present value

B B B B

H7CX-A@-N

Counter

Input/Output Mode Settings

I/O Functions for Counter Operation

If a 1-stage model or 2-stage model is incorrectly used as twin counter, the operation for

output 2 will be performed. When using a 2-stage model as a 1-stage preset counter,

total and preset counter, or dual counter, OUT1 and OUT2 turn ON and OFF

simultaneously.

Input mode Operation after count

completion

UP DOWN UP/DOWN A, B, C

Output

mode

setting

The outputs and present

value display are held

until reset/reset 1 is

input.

The present value

display continues to

increase/decrease.

The outputs are held until

reset/reset 1 is input.

As soon as the count

reaches SV, the present

value display returns to

the reset start status.

The present value display

does not show the

present value upon count-

up.

The outputs repeat one-

shot operation.

OUT1 self-holding output

turns OFF after the OUT2

one-shot output time.

The OUT1 one-shot

output time is

independent of OUT2.

The present value

display returns to the

reset start status after

the one-shot output time.

The outputs repeat one-

shot operation.

OUT1 self-holding output

turns OFF after the

OUT2 one-shot output

time.

The OUT1 one-shot

output time is

independent of OUT2.

K-1

The present value

display continues to

increase/decrease.

OUT1 self-holding output

turns OFF after the

OUT2 one-shot output

time.

The OUT1 one-shot

output time is

independent of OUT2.

Self-holding

output

Self-holding

output

One-shot output from OUT1

One-shot

output from OUT2

(The one-shot output time can be

set in the range 0.01 to 99.99s.)

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

999999

Reset/

reset 1

OUT1

OUT2

Set value 2

Set value 1

999999

Reset/

reset 1

OUT1

OUT2

Set value 2

Set value 1

999999

Reset/

reset 1

OUT1

OUT2

Set value 2

Set value 1

999999

Reset/

reset 1

OUT1

OUT2

Set value 2

Set value 1

H7CX-A@-N

Counter

Note: 1. The full scale (FS) for H7CX 4-digit models is 9999.

2. When the present value reaches 999999, it returns to 0.

3. Counting cannot be performed during reset/reset 1 input.

4. If reset/reset 1 is input while one-shot output is ON, one-shot output turns OFF.

5. If there is power failure while output is ON, output will turn ON again when the power supply has recovered.

For one-shot output, output will turn ON again for the duration of the output time setting once the power supply has recovered.

6. Do not use the counter function in applications where the count may be completed (again) while one-shot output is ON.

7. The setting range is 0 to 999999 (0 to 9999 for 4-digit models).

Self-holding

output

Self-holding

output

One-shot output from OUT1

One-shot

output from OUT2

(The one-shot output time ca

set in the range 0.01 to 99.9

Input mode Operation after

count completion

UP DOWN UP/DOWN A, B, C

Output

mode

setting

The present value

display does not

change during the

one-shot output time

period, but the actual

count returns to the

reset start status.

The output will return

to one-shot mode.

The outputs repeat

one-shot operation.

OUT1 self-holding

output turns OFF after

the OUT2 one-shot

output time.

The OUT1 one-shot

output time is

independent of OUT2.

The present value

continues to increase/

decrease for the one-

shot output time, but

returns to the reset

start status after the

one-shot output time

has elapsed.

The outputs repeat

one-shot operation.

OUT1 self-holding

output turns OFF after

the OUT2 one-shot

output time.

The OUT1 one-shot

output time is

independent of OUT2.

The present value

display and OUT1

self-holding output is

held until reset/reset 1

is input.

OUT1 and OUT2 are

independent.

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

H7CX-A@-N

Counter

Note: 1. Counting cannot be performed during reset/reset 1 input.

2. If reset/reset 1 is input while one-shot output is ON, one-shot output turns OFF.

3. If there is power failure while output is ON, output will turn ON again when the power supply has recovered.

For one-shot output, output will turn ON again for the duration of the output time setting once the power supply has recovered.

4. Do not use the counter function in applications where the count may be completed (again) while one-shot output is ON.

5. The set value is from −99999 to 999999 (−999 to 9999 for 4-digit models).

One-shot

output

Self-holding

output

Instantaneous

(equals) output

(The one-shot output time can be

set in the range 0.01 to 99.99s.)

Input mode Operation after count completion

UP/DOWN A, B, C

Output

mode

setting

K-2

The display continues to increase/

decrease until the overflow or

underflow value is reached.

One-shot output only.

The display continues to increase/

decrease until the overflow or

underflow value is reached.

The outputs are ON while the count is

equal.

The display continues to increase/

decrease until the overflow or

underflow value is reached.

OUT1 is held while the present value

is less than or equal to set value 1.

OUT2 is held while the present value

is greater than or equal to set value 2.

The display continues to increase/

decrease until the overflow or

underflow value is reached.

OUT1 is held while the present value

is greater than or equal to set value 1.

OUT2 is held while the present value

is greater than or equal to set value 2.

* H mode is available only when using a

model as a 2-stage counter.

−99999

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

−99999

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

−99999

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

−99999

Reset/

reset 1

OUT1

OUT2

999999

Set value 2

Set value 1

H7CX-A@-N

Counter

Total and Preset Counter Operation

The H7CX has a total counter, separate from the 1-stage preset counter, for counting the total accumulated value.

Batch Counter Operation

The H7CX has a batch counter, separate from the 1-stage preset counter, for counting the number of times the count has been completed.

Note: 1. The batch count value is held at 0 during batch counter reset input.

2. If the batch count set value is 0, batch count will be performed but there will be no batch output.

3. The batch count value returns to 0 when it reaches 999,999 (9,999 for 4-digit models).

4. Once batch input has been turned ON, it will return to the ON state after power interruptions.

5. If the batch count set value is changed from a value that is greater than the batch count value to one that is less, batch output will turn ON.

6. After batch output turns ON, the ON state will be held even if the batch count set value is changed to a value greater than the batch count value.

Dual Counter Operation

Using the dual counter allows the count from 2 inputs to be added or subtracted and the result displayed. It is possible to specify a set value for

which output turns ON when the set value matches the added or subtracted result.

Note: 1. Counting is not possible for CP1 during reset 1 input. CP2 will not be affected. The dual count value will be calculated based on a CP1 present value of 0.

2. Counting is not possible for CP2 during reset 2 input. CP1 will not be affected. The dual count value will be calculated based on a CP2 present value of 0.

3. The counting range for the dual count value is −99,999 to 999,999 (0 to 9,999 for 4-digit models).

The counting ranges for the CP1 present value and CP2 present value are 0 to 999,999 (0 to 9,999 for 4-digit models).

If a present value exceeds 999,999 (9,999 for 4-digit models), FFFFFF (FFFF for 4-digit models) will be displayed to indicate an overflow, and all counting

will stop.

• The total counter continues to count the total

accumulated value when the present value is

reset using reset/reset 1 input (Reset Key).

• The total count value is reset when the total

reset/reset 2 input is turned ON.

If the Reset Key is pressed while the total count

value is displayed, the total count value is reset.

The present value is also reset at this time.

• The counting range of the total counter is

−99,999 to 999,999 (−999 to 9,999). The total

count value returns to 0 when it reaches the full

scale limit.

• The batch counter continues after count

completion.

• Batch output is held until batch counter reset is

input.

• When the batch counter reset input is turned

ON, the batch count value is reset, and batch

output turns OFF.

• If the Reset Key is pressed while the batch

count value is displayed, the batch count value

is reset and batch output turns OFF. The

present value is also reset at this time.

• The count value can be incremented and

decremented.

The batch count is only incremented.

• The maximum counting speed for batch counter

operation is 5 kHz. The batch counter counts

the number of times the count reaches the set

value.

• The operation after count completion for the

dual counter value is determined by the output

mode.

• The CP1 present value is reset when reset 1

input is turned ON.

The CP2 present value is reset when reset 2

input is turned ON.

• If the Reset Key is pressed while the dual count

value, CP1 present value, or CP2 present value

is displayed, all of the present values are reset

and outputs turn OFF. At this time, counting is

not possible for CP1 or CP2 inputs.

Reset/reset 1

Total Reset or Reset 2

Present value

Total count value

999999

Note: The full scale (FS) for H7CX 4-digit models is 9999.

Batch count set value

Sub-display

OUT1

(batch output)

Batch count value

(Main display) 1

Reset 1

Set value

OUT2

Present value

Note: The above is for when the output mode is C.

Reset 2 (batch

counter reset)

Reset 1 (CP1 reset)

Reset 2 (CP2 reset)

Dual count set value

Dual count value

CP1 present value

CP2 present value

OUT1, OUT2

Note: The above is for when the output mode is N.

Reset 1 (CP1 reset)

Reset 2 (CP2 reset)

Dual count set value

Dual count value

CP1 present value

CP2 present value

OUT1, OUT2

Note: The above is for when the output mode is K-2.

SUB mode can be used only when K-2, D, L,

or H is selected as the output mode with

6-digit models.

(1) Dual Count Calculating Mode = ADD

Dual count value = CP1 PV + CP2 PV

(2) Dual Count Calculating Mode = SUB

Dual count value = CP1 PV − CP2 PV

H7CX-A@-N

Counter

Twin Counter Operation

Two independent counters are built in.

Note: 1. Only 2-stage models

2. Increment mode only for counters 1 and 2.

3. The settings for prescaling and the decimal point are used by both counter 1 and 2.

Reset Function List

I/O Functions for Counter Operation

• The following table shows the delay from when the present value passes the set value until the output is produced.

Actual measurements in N and K-2 modes (Reference values)

Note: The above times may vary slightly depending on the mode or operating conditions.

Counter 1 Counter 2

Counter input CP1 CP2

Reset input Reset 1 Reset 2

Present value display and

setting

Reset Key Only counters appearing on the display will be reset.

Function

1-stage/2-

stage preset

counter

Total and preset counter Batch counter Dual counter Twin counter

Screen dis-

played in run

mode

Present value/

set value (1, 2)

Present

value/set

value

Total count

value

Present

value/set

value

Batch count

value/batch

count set

value

Dual count

value/dual

count set

value

CP1 present

value/CP2

present

value

Present

value 1/Set

value 1

Present

value 2/Set

value 2

Reset/reset 1

Present value

and output

reset.

Present value and output

reset.

Present value and output

reset.

Only the CP1 present value is

reset.

Only the CP1 present value is

reset.

Total reset or

reset 2 No effect Only the total count value is

reset.

Batch count value and batch

output reset.

Only the CP2 present value is

reset.

Only the CP2 present value is

reset.

Reset Key

Present value

and output

reset.

Present value

and output

reset.

Present

value, total

count value,

and output

reset.

Present value

and output

reset.

Present

value, batch

count value,

output and

batch output

reset.

CP1 present value, CP2

present value, dual count

value, and output reset.

CP1 present

value reset

CP2 present

value reset

Control output type Max. counting speed Output delay time

Contact output 30 Hz 16.5 to 24.0 ms

5 kHz 3.7 to 5.6 ms

Transistor output 30 Hz 12.0 to 20.0 ms

5 kHz 0.2 to 0.55 ms

Counter 1 present value

Counter 1 set value

Counter 2 present value

Counter 2 set value

Counter 1 display Counter 2 display

Switched with

the Key.

H7CX-A@-N

Tachometer

Setting Procedure Guide

Tachometer Operation

After making DIP switch settings for basic operations, advanced functions can be added using the operation keys.

For details, refer to page page 28.

Step1 The H7CX is factory-set to the 2-stage counter configuration (1-stage counter configuration for

H7CX-AU@-N models).

Enter configuration selection mode using the following chart and set the tachometer mode.

OFF

Upper/lower limit output

Range output

Upper limit output

Lower limit output

OFF

2 times

4 times

8 times

--- ------

Step2

Key-protect switch

Disabled Enabled

Refer to the table on the right.

30 Hz 10 kHz

DIP switch settings

Counting speed

Tachometer output mode

Average processing

Input selection NPN PNP

Note: All pins are factory-set to OFF.

Step3

Set the basic parameters.

(If the desired I/O mode is not listed below or to set all parameters using the front panel keys, perform ,

below.)

Note: can be performed first, followed by .

Item OFF ON

Step2 Step1

Hold down for 1 s min.

Switch from 2cnt (2-stage preset counter mode) to taco (tachometer mode)

using the U Key.

Run mode

Power ON

Hold down for 1 s min.

Configuration

selection mode

Refer to the table on the right.

Tachometer output modePin 4Pin 3

Average processingPin 6Pin 5

• When setting functions using the DIP switch, be sure to set pin 1 of the DIP switch to ON.

• DIP switch settings are effective when the power is turned ON again. (Perform DIP switch settings while the power is OFF.)

Be sure to set pin 1 to ON.

OFF

12345678

H7CX-A@-N

Tachometer

Step3

(No decimal point) (One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

(Four digits after

decimal point)

(30 Hz) (10 kHz)

(99.9 s)(0.0 s)

(999.9 s)(0.1 s)

(99.999)(1.000)(0.001)

(No average

processing)

(Average of 2

measurements)

(Average of 4

measurements)

(Average of 8

measurements)

(Average of 16

measurements)

(Simple

averaging)

(Moving

average)

(LO)(HI)

(AREA) (HI-HI) (LO-LO)(HI-LO)

hilo

30hz

--.----

0.001

smp mv

off

0.1 999.9

0.0 99.9

24816

1.000 99.999

area hihi lolo

(Error)

(Absolute ratio)

(1 input) (2 inputs)

f1 f2 f3 f4

(Error ratio)

lohi

Run mode

Power ON

Function

setting mode

*1 Set tachometer output modes 1 and 2 using the

U Key.

3 s min.

Parameters that cannot be set with the DIP switch are set with the operation keys on the front panel.

Change to Function Setting Mode.

Counting

speed

(CNTS)

Tachometer

output mode

(TOTM)

Auto-zero

time

(AUT00)

Startup time

(STMR)

Average

processing

(AVGN)

Decimal point

position

(DP)

The characters displayed in reverse video are the default settings.

When performing settings with operation keys only, set pin1 of the DIP switch to OFF (factory setting).

If pin 1 of the DIP switch is set to ON, the setting items indicated by will not be displayed.

To next pageFrom next page

Prescale

value

(PSCL)

Averaging

method

(AVGT)

• Set the tachometer input mode using the U Key.

Tachometer

output

mode 1

(TO1M)

* Displayed only when the tachometer input mode is F2

(2 inputs).

Function Setting Mode

*1 If the mode is switched to the function setting mode during operation, operation will continue.

*2 Changes made to settings in function setting mode are enabled for the first time when the mode is changed to run mode.

Also, when settings are changed, the counter is reset (measured value initialized and outputs turned OFF) on returning to run mode.

Tachometer

input mode

(TINM)

• Set the tachometer output mode using the U Key.

• Set the counting speed using the U Key.

• Set the decimal point position using the U Key.

• Set each digit using the individual U Key.

Note: “--.----“ will be displayed when pulse width measurement is set or when the display unit is set to seconds.

• Set the averaging method using the U Key.

• Set the number of averaging times using the U Key.

• Set each digit using the individual U Key.

Tachometer

output

mode 2

(TO2M)

Note: Even if 10 kHz is selected when the tachometer input mode is F2 to F5, the counting speed will be 5 kHz.

For details on operations and display in run mode, refer to page page 33.

H7CX-A@-N

Tachometer

(Enabled)(Disabled)

(Red) (Green) (Orange)

(Red-green) (Green-red)

(Red-orange) (Orange-red)

(Green-orange) (Orange-green)

(PNP input)(NPN input)

(

19.99 s)

(

0.00 s)

99990

(99999

)

999990

(999999

)

999999

onoff

grnred org r-g g-r r-o o-r g-o o-g

npn pnp

19.990.00

(9999 × 1000 times)(0 × 1000 times)

*2 Set each digit using the individual U Keys.

From previous

page

To previous

page

• Set the NPN/PNP input mode using the U Key.

Output 1

(OUT1) ON

count alarm

set value

Output 2

(OUT2) ON

count alarm

set value

Output 1

(OUT1) ON

count monitor

value

Function Setting Mode

NPN/PNP

input mode

(IMOD)

Display

color

(COLR)

Note: The monitor value is only

displayed. It cannot be set.

Output 2

(OUT2) ON

count

monitor value

Peak/bottom

hold enabled

(DHLD)

Output

hysteresis

(HYS)

Output OFF

delay

(OFFD)

Set value

upper limit

(SL-H)

• Set the display color using the U Key.

• Enable or disable the peak/bottom hold using the U Key.

• Set the output hysteresis using the U Key.

Note: The measurement value after prescaling is set.

• Set each digit using the individual U Key.

Note: The monitor value is only

displayed. It cannot be set.

(

)

(Pulse width

measurement)

(Pulse cycle

measurement)

(

Hz)

(Cont (10 ms min.))

(

200 ms)

(

KP-1)

(

KP-2)

(

KP-3)

(

KP-4)

(

KP-5)

(

KP-6)

(

KP-7)

phas

shz

cont200ms

kp-1 kp-2 kp-3 kp-4 kp-5 kp-6 kp-7

Key protect

level

(KYPT)

Pulse cycle

measurement/

pulse width

measurement

(CALM)

Display unit

(UNIT)

Measurement

interval

(INTV)

Output ON

count alarm set

value/monitor

value

• Set the key protect level using the U Key.

• Set pulse cycle measurement or pulse width measurement using the U Key.

• Set the display unit using the U Key.

Note: Displayed only when pulse cycle measurement is

used.

• Set each digit using the individual U Key.

Note: Displayed only if the measurement speed is 10 kHz

when pulse cycle measurement is used.

(ON)(OFF)

onoff

Output

allocation

change

Note: Displayed only for "-AU@" models.

off: Output 1 = 12, 13, Output 2 = 3, 4, 5

on: Output 1 = 3, 4, 5, Output 2 = 12, 13

The numbers are the terminals numbers.

H7CX-A@-N

Tachometer

Explanation of Functions

Tachometer Operation

Items marked with stars ★ can be set using the DIP

switch.

Tachometer Input Mode (tinm)

Set the count input mode to one of the following: 1 input (F1), 2 inputs

(F2), error (F3), absolute ratio (F4), or error ratio (F5).

Tachometer Output Mode (totm)★

Set the output method for control output based on the comparison

value. Upper and lower limit (HI-LO), area (AREA), upper limit (HI-HI),

and lower limit (LO-LO) can be set.

(For details on the output modes, refer to Output Mode Settings and

Operation on page page 34.)

Counting Speed (cnts)★

Set the maximum counting speed (30 Hz/10 kHz) for CP1 input.

If contacts are used for input signals, set the counting speed to 30 Hz.

Processing to eliminate chattering is performed for this setting.

Decimal Point Position (dp)

Decide the decimal point position for the measurement value, OUT1

set value, and OUT2 set value.

Prescale Value (pscl)

It is possible to display the rate of rotation or the speed of a device or

machine to which the H7CX is mounted by converting input pulses to

a desired unit.

If this prescaling function is not used, the input frequency (Hz) will be

displayed.

It is also possible to specify time (seconds) as the display value. Refer

to Display Unit on page page 31 for details.

The relationship between display and input is determined by the

following equation. Set the prescale value according to the unit to be

displayed.

Displayed value = f × α

f: Input pulse frequency (number of pulses in 1 second)

α: Prescale value

(1) Displaying Rotation Rate

N: Number of pulses per revolution

Example: To display the rate of rotation for a machine that outputs 5

pulses per revolution in the form @@.@ rpm:

1. Set the decimal point position to 1 decimal places.

2. Using the formula, set the prescale value (α) to 1/N × 60 = 60/5 = 12.

(2) Displaying Speed

N: Number of pulses per revolution

d: Diameter of rotating body (m)

πd: Circumference (m)

• Observe the following points when

setting a prescale value.

Set the set value to a value less than {Maximum countable value −

Prescale value}.

Example: If the prescale value is 1.25 and the counting range is

0.000 to 999.999, set the set value to a value less than 998.749 (=

999.999 − 1.25).

If the set value is set to a value greater than this, output will not turn

ON.

* Output will turn ON, however, if a present value overflow occurs (FFFFFF or FFFF}.

Averaging Method (avgt) (Only for Tachometer Operation)

A simple average or moving average can be selected for the

averaging. With the moving average method, the average of the

measurement values is displayed each sampling cycle, in contrast to

a simple average, with which the the average of the set number of

samples is displayed.

Number of Averaging Times (avgn)★

Flickering display and output chattering can be prevented using

average processing. Average processing can be set to one of four

levels: no average processing, 2 times (i.e., the average of 2

measurement values), 4 times, 8 times, or 16 times.

The measurement cycle will be equal to the sampling cycle multiplied

by the average processing setting (i.e., the number of times).

Average processing enables stable displays even for fluctuating input

signals. Set the optimum number of times for the application.

Auto-zero Time (auto0)

The display can be force-set to 0 if there is no pulse for a certain

period of time. This time is called the auto-zero time. Set the auto-zero

time to a time slightly longer than the estimated interval between input

pulses. Accurate measurement is not possible if the auto-zero time is

set to a time shorter than the input pulse cycle. Setting a time that is

too long may also result in problems, such as a time-lag between

rotation stopping and the alarm turning ON. The auto-zero time is not

applied to pulse width measurements.

Startup Time (stmr)

To prevent undesired outputs resulting from unstable inputs

immediately after the power supply is turned ON, it is possible to

prohibit measurement for a set period of time, the startup time.

It can also be used to stop measurements and disable outputs until

the rotating body reaches the normal rate of rotation, after the power

supply to the H7CX and rotating body are turned ON at the same time.

Input

mode Input Internal

processing Application

1 input Count 1 None Operation with only one input.

2 inputs Counts 1 and 2 None Operation with two

independent inputs.

Error Counts 1 and 2 Count 1 input −

Count 2 input

Measuring the difference

between two inputs (error in

number of revolutions).

Absolute

ratio Counts 1 and 2 Count 1 input ÷

Count 2 input

Measuring the ratio of two

inputs (ratio of number of

revolutions).

Error ratio Counts 1 and 2

(Count 1 input −

Count 2 input) ÷

Count 2 input

Measuring the ratio of error

for two inputs (measuring the

error ratio of number of

revolutions).

Display unit Prescale value (α)

rpm 1/N × 60

rps 1/N

Display unit Prescale value (α)

m/min πd × 1/N × 60

m/s πd × 1/N

d: Diameter

of rotating

body (m)

Note: If the prescale value setting is incorrect, a counting error will

occur. Check that the settings are correct before using this

function.

Startup timeDisplay

Time

Comparison value

(lower limit)

Output

(lower limit)

Power supply

H7CX-A@-N

Tachometer

NPN/PNP Input Mode (imod)★

Select either NPN input (no-voltage input) or PNP input (voltage

input) as the input format.

When using a two-wire sensor, select NPN input. The same setting is

used for all external inputs.

For details on input connections, refer to Input Connections on page

page 9.

Display Color (colr)

Set the color used for the measurement value.

*1. If the tachometer output mode is set to AREA, however, the measured

value is displayed in red when control output 1 is OFF and in green when

control output 1 is ON.

*2. If the tachometer output mode is set to AREA, however, the measured

value is displayed in green when control output 1 is OFF and in red when

control output 1 is ON.

*3. If the tachometer output mode is set to AREA, however, the measured

value is displayed in red when control output 1 is OFF and in orange when

control output 1 is ON.

*4. If the tachometer output mode is set to AREA, however, the measured

value is displayed in orange when control output 1 is OFF and in red when

control output 1 is ON.

*5. If the tachometer output mode is set to AREA, however, the measured

value is displayed in green when control output 1 is OFF and in orange

when control output 1 is ON.

*6. If the tachometer output mode is set to AREA, however, the measured

value is displayed in orange when control output 1 is OFF and in green

when control output 1 is ON.

Peak/bottom Hold Enabled (dhld)

This function records the peak and bottom (i.e., minimum) after

counting starts (after turning ON the power supply or changing the

configuration selection mode or function setting). The peak value is

also held when the power supply is interrupted.

Output Hysteresis (hys)

This setting can be used to prevent output chattering if the

measurement value fluctuates slightly near the set value.

The measurement value after prescaling is set.

Output OFF Delay (offd)

This function delays the timing for turning OFF comparative output by

a certain time.

The ON time can be held for the set time if the comparative result

changes in a short time.

Operation will continue and outputs will not change when holding the

value.

Set Value Upper Limit (pl-h)

Set the upper limit for the set value when it is set in run mode. The

limit can be set to between 1 and 999999.

Output Allocation (otst)

When using an H7CX-AU@-N model as 2-stage counter, each output

can be flexibly allocated to either stage 1 or 2.

The transistor output can be allocated to SV1 and the contact output

to SV2 or vice verse, as in the following tables.

H7CX-AU-N/-AUD1-N

H7CX-AUSD1-N

Key Protect Level (kypt)

Set the key protect level.

Refer to Key Protect Level on page page 36.

Pulse Cycle Measurement/Pulse Width Measurement

(calm)

Set the measurement mode to pulse cycle measurement or pulse

width measurement.

With pulse cycle measurement, the number of pulse cycles that occur

in 1 s is measured.

With pulse width measurement, the ON time for one pulse is

measured.

An input OFF period of at least 20 ms is required for pulse width

measurement.

If there is no input pulse during pulse width measurement, the

previously measured value will be held.

Display Unit (unit)

When pulse cycle measurement is used, set the display unit to Hz

(hertz) or s (seconds).

Counting Interval (intv)

If the measurement speed is 10 kHz when pulse cycle measurement

is used, set the measurement interval to 200 ms or Cont (10 ms min.).

Control output OFF Control output ON

red Red (fixed)

grn Green (fixed)

org Orange (fixed)

r-g *1

Measured value is

displayed in red when

both control outputs 1

and 2 are OFF.

Measured value is

displayed in green when

either control output 1 or

control output 2 is ON.

g-r *2

Measured value is

displayed in green when

both control outputs 1

and 2 are OFF.

Measured value is

displayed in red when

either control output 1 or

control output 2 is ON.

r-o *3

Measured value is

displayed in red when

both control outputs 1

and 2 are OFF.

Measured value is

displayed in orange

when both control

outputs 1 and 2 are

OFF.

o-r *4

Measured value is

displayed in orange

when both control

outputs 1 and 2 are

OFF.

Measured value is

displayed in red when

both control outputs 1

and 2 are OFF.

g-o *5

Measured value is

displayed in green when

both control outputs 1

and 2 are OFF.

Measured value is

displayed in orange

when both control

outputs 1 and 2 are

OFF.

o-g *6

Measured value is

displayed in orange

when both control

outputs 1 and 2 are

OFF.

Measured value is

displayed in green when

both control outputs 1

and 2 are OFF.

Output 1 Output 2

off Transistor (12-13) Contact (3, 4, 5)

on Contact (3, 4, 5) Transistor (12-13)

Output 1 Output 2

off Transistor (12-13) Transistor with diode (3, 4, 5)

on Transistor with diode (3, 4, 5) Transistor (12-13)

OUTX1

OUTY2

Display value

Comparison value 2 Hysteresis

Hysteresis

Comparison value 1

Set the hysteresis for when

the output turns OFF.

H7CX-A@-N

Tachometer

ON Count Alarm Set Values for Outputs 1 and 2 (OUT1

and OUT2) (on1a and on2a)

Set the ON count alarm values for the outputs 1 and 2.

The limit can be set to between 0 × 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of instantaneous output 1 or 2 exceeds the alarm

set value, e3 will be displayed on the Timer to indicate that the output

ON count alarm value was exceeded. Refer to Self-diagnostic

Function on page page 36 for information on the e3 display.

ON Count Monitor Values for Outputs 1 and 2 (OUT1 and

OUT2) (on1c and on2c)

The monitor value for output 1 or 2 is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

H7CX-A@-N

Tachometer

Operation in Run Mode

Tachometer Operation

Bottom hold value

Peak hold value

Bottom hold value 1

Peak hold value 1

Bottom hold value 2

Peak hold value 2

Measurement value 1

Comparison value 1

Measurement value 2

Comparison value 2

Measurement value

• Set each digit using the individual U Keys.

Displayed when the input mode is not 2 inputs.

• Measurement value

Displays the currently measured value.

• Comparison value 1/Comparison value 2

Set comparison value 1 and comparison value 2.

The measurement value is compared to

comparison value 1 and comparison value 2 and

output is made according to the selected output

mode.

*1 Measurement value 1 for the 2-input input mode.

*2 Measurement value 2 for the 2-input input mode.

*3 Peak/bottom hold enabled

Displayed for the 2-input input mode.

• Peak/bottom hold value

The peak (maximum) and bottom (minimum)

values are displayed after counting starts.

• Peak/bottom hold value 2

Peaks (maximums) 1 and 2 and bottoms

(minimums) 1 and 2 are displayed after counting

starts.

Note: The held values will be initialized when

the Reset Key (Hold Key) or reset 1 input

is turned OFF while peak/bottom hold

values 1 and 2 are being displayed. (The

reset 2 input operates in the same way if

the input mode is set to 2-input mode.)

H7CX-A@-N

Output Mode Setting and Operation

Tachometer Operation

Input mode

setting

Output mode

setting Operation

1 input

Error

Absolute ratio

Error ratio

Upper and

lower limit

(HI-LO)

Area (AREA)

Upper limit

(HI-HI)

Lower limit

(LO-LO)

2 inputs

Upper limit

(HI)

Lower limit

(LO)

OUT1

OUT2

Measurement value

(Upper-limit)

Comparison value 2

(Lower-limit)

Comparison value 1

ON condition for OUT1: Measurement value ≤ Comparison value 1

ON condition for OUT2: Measurement value ≥ Comparison value 2

OUT1

OUT2

Measurement value

Comparison value 2

Comparison value 1

Condition Comparison value 1 ≤

Comparison value 2

Measurement value 1 >

Comparison value 2

ON condition

for OUT1

Comparison value 1 ≤

Measurement value ≤

Comparison value 2

Comparison value 2 ≤

Measurement value ≤

Comparison value 1

ON condition

for OUT2

Measurement value <

Comparison value 1 or

Measurement value >

Comparison value 2

Measurement value <

Comparison value 2 or

Measurement value >

Comparison value 1

OUT1

OUT2

Measurement value

(Upper-limit)

Comparison value 2

(Lower-limit)

Comparison value 1

ON condition for OUT1: Measurement value ≥ Comparison value 1

ON condition for OUT2: Measurement value ≥ Comparison value 2

OUT1

OUT2

Measurement value

(Upper-limit)

Comparison value 2

(Lower-limit)

Comparison value 1

ON condition for OUT1: Measurement value ≤ Comparison value 1

ON condition for OUT2: Measurement value ≤ Comparison value 2

OUT1

CP1 display value

Comparison value 1

Output 1

OUT2

CP2 display value

Comparison value 2

Output 2

ON condition for output 1: CP1 present value (display value) ≥ Comparison value 1

ON condition for output 2: CP2 present value (display value) ≥ Comparison value 2

OUT1

CP1 display value

Comparison value 1

Output 1

OUT2

CP2 display value

Comparison value 2

Output 2

ON condition for output 1: CP1 present value (display value) ≤ Comparison value 1

ON condition for output 2: CP2 present value (display value) ≤ Comparison value 2

H7CX-A@-N

Switching between Preset Counter, Total and Preset Counter, Batch Counter, Dual

Counter, Twin Counter, and Tachometer Operation

Select which H7CX configuration is used (i.e., preset counter, total and preset counter, batch counter, dual counter, twin counter, or tachometer)

in configuration selection mode.

The H7CX is also equipped with a DIP switch monitor function, a convenient function that enables the settings of the DIP switch pins to be

confirmed using the display on the front of the H7CX.

Hold Function

The measurement value (display value) and output are sustained while the hold input is ON.

Note: The output will maintain the current status when the hold key is pressed.

Example:

Output mode

setting Operation

Lower limit

RST

bcnt dcnt tacotwn1cnt 2cnt tcnt

Key

Key Key

…Indicates that DIP switch pin 8 is ON.

…Indicates that DIP switch pin 7 is OFF.

…Indicates that DIP switch pin 6 is ON.

…Indicates that DIP switch pin 5 is OFF.

…Indicates that DIP switch pin 4 is ON.

…Indicates that DIP switch pin 3 is OFF.

…Indicates that DIP switch pin 2 is ON.

…Indicates that DIP switch pin 1 is ON.

*The configurations that can be selected depend on the model.

Press the

key for 1 s

min.

*1 When the mode is changed to configuration selection mode, the present value is reset, outputs turn OFF, and counting (measuring) stops.

*2 Setting changes made in configuration selection mode are enabled when the mode is changed to run mode. If the configuration is changed, the

set value (or set value 1 and set value 2), comparison value 1 and comparison value 2 are initialized.

Power ON

Example

Configuration

selection

Note

DIP switch

monitor

(DIP)

Convenient

*2 *1

*This display is possible only when DIP switch pin 1 (DIP switch settings enable/disable)

is set to ON (enable).

Select the configuration using the UD Key.

Run mode

Configuration Selection Mode

To change the mode to configuration selection mode, hold

down the Key for 1 s min. with the Key held down.

The mode will not change if the Key is pressed first.

(1-stage

preset

counter)

(2-stage

preset

counter)

(Total and

preset counter)

(Batch

counter)

(Dual

counter)

(Twin

counter)

(Tachometer)

Note: By default, the H7CX is set to the 1-stage preset counter configuration. (Two-stage

models are set to the 2-stage preset counter configuration.)

Confirm the status of DIP switch pins 1 to 8 using the UD Key.

OFF

12345678

OUT

Display value

Hold input* (Reset Key)

Comparison value (lower limit)

Sustained display value

Sustained output

Actual input

H7CX-A@-N

Key Protect Level

It is possible to prevent setting errors by prohibiting the use of certain operation keys by specifying the key protect level (KP-1 to KP-7) when the

key-protect switch is set to ON.

The key protect level is set in the function setting mode. The key protect indicator is lit when the key-protect switch is ON.

* Changing mode to configuration selection mode or function setting mode.

Self-diagnostic Function

The following displays will appear if an error occurs.

*1. Displays for 4-digit models are given in parentheses.

*2. This includes times when the life of the EEPROM has expired.

*3. This occurs if the present value or total count value falls below −99999

(−999 for 4-digit models).

*4. This occurs in the following conditions if the present value (i.e.,

measurement value) exceeds 999999 (9999 for 4-digit models).

• For Output Modes K-2, D, L, or H

• Dual counter or tachometer operation is used.

*5. Display flashes.(1-second cycles)

*6. This does not apply when tachometer operation is used.

*7. This is displayed if the alarm value setting for either of the two outputs is

exceeded if a model with two outputs is used.The total ON count will not be

cleared by using the Reset Key.

*8. The normal display and e3 will appear alternately.

When the Reset Key is pressed, e3 will not be displayed even if the alarm

set value is exceeded.

(Monitoring is possible, however, because the counter will continue without

the output ON count being cleared.)

Level Description

Details

Changing modes* Switching display

during operation Reset Key Up/Down Keys

KP-1

(default setting) Invalid Valid Valid Valid

KP-2 Invalid Valid Invalid Valid

KP-3 Invalid Valid Valid Invalid

KP-4 Invalid Valid Invalid Invalid

KP-5 Invalid Invalid Invalid Invalid

KP-6 Invalid Invalid Valid Valid

KP-7 Invalid Invalid Invalid Valid

*Factory-set to OFF

(Enable)

OFF

(Disable)

Key protect indicator

Main display Sub-display Description Output status Correction method Set value after reset

----- (----)*1*5 No change Present value underflow*3 No change Either press the Reset Key or turn

ON reset input. No change

fffff (ffff)*1*5 No change Present value overflow*4 No change Either press the Reset Key or turn

ON reset input.*6 No change

e1 Not lit CPU error OFF Either press the Reset Key or

reset the power supply. No change

e2 Not lit Memory error (RAM) OFF Turn ON the power again. No change

e2 sum Memory error (EEPROM)*2 OFF Reset Key Factory setting

e3*8 No change Output Counter Overflow No change Reset Key*7 No change

H7CX-R@-N

• Tachometer-only model (DIN 48

48) for the H7CX

(Supports display and alarm outputs for numbers of rotations,

speed, and flow rate.)

• Socket design allows either flush or surface mounting.

•

"-W" models added to provide two sets of measurement controls.

•

Operation in any of the four following modes is possible with the

same Unit: Upper and lower limit, upper limit, lower limit, and area.

• Equipped with auto-zero time, average processing, and startup

time functions.

*The prescale value and auto-zero time settings are one.

Specifications

Ratings

*1. Do not use the output from an inverter as the power supply. The ripple must be 20% maximum for CC power.

*2. The display is lit only when the power is ON. Nothing is displayed when power is OFF.

H7CX-R@-N Tachometer

For the most recent information on models that have been certified for

safety standards, refer to your OMRON website.

Classification Tachometer

Item Model H7CX-R11@-N H7CX-R11W@-N

Input mode 1 input only 2 inputs only

Ratings

Power supply volt-

age*1

• 100 to 240 VAC, 50/60 Hz

• 12 to 24 VDC or 24 VAC, 50/60 Hz

Operating voltage

fluctuation range 85% to 110% of rated supply voltage (90% to 110% at 12 to 24 VDC)

Power consumption Approx. 9.4 VA at 100 to 240 VAC, Approx. 7.2 VA/4.7 W at 24 VAC/12 to 24 VDC, Approx. 3.7 W at 12 to 24 VDC

Mounting method Flush mounting or surface mounting

External connections 11-pin socket

Degree of protection IEC IP66, UL508 Type 4 (indoors) for panel surface only and when Y92S-29 Waterproof Packing is used

Input signals Count and hold Count 1 and count 2

Pulse measurement method Tachometer mode (cycle measurement) AMD-compatible mode (continuous

measurement) Tachometer mode (cycle measurement)

Maximum counting speed

30 Hz

(minimum pulse

width: 16.7 ms)

10 kHz

(minimum pulse

width: 0.05 ms)

---

30 Hz (minimum pulse width: 16.7 ms) or 5 kHz

(minimum pulse width: 0.1 ms) (selectable)

Minimum input signal width --- 10 ms 1 ms ---

Measuring ranges

0.001 Hz to 30.00Hz

0.001 Hz to 10 kHz

0.026 to 999999 s 0.003 to 999999 s 0.01 to 5k Hz

Sampling cycle 200 ms min. Continuous measurement (minimum

interval of 10 ms) 200 ms min.

Display refresh cycle

• Input pulse of 5 Hz min.

Averaging not used: 200 ms

Averaging used: 200 multiplied by the averaging setting (ms)

• Input pulse of less than 5 Hz

Averaging not used: Two times the maximum input pulse cycle

Using averaging: Two times the maximum of the input pulse cycle multiplied by the averaging setting.

Measuring accuracy ±0.1% FS ±1 digit max. (at 23 ±5°C)

Output mode HI-LO, AREA, HI-HI, LO-LO HI-HI, LO-LO

Auto-zero time 0.1 to 999.9 s (in Tachometer Mode)

Startup time 0.0 to 99.9 s

Averaging Simple averaging/moving averaging selectable, Number of times: OFF, 2, 4, or 8 times

Prescaling function 0.001 to 99.999 (in Tachometer Mode)

Decimal point adjustment Rightmost 3 digits ---

Sensor waiting time 290 ms max. (Control output is turned OFF and no input is accepted during sensor waiting time.)

Input Input method

No-voltage Input

Impedance when ON: 1 kΩ max.

(Leakage current: 12 mA when 0 Ω)

ON residual voltage: 3 V max.

Impedance when OFF: 100 kΩ min.

Voltage Input

High (logic) level: 4.5 to 30 VDC

Low (logic) level: 0 to 2 VDC

(Input resistance: approx. 4.7 kΩ)

No-voltage input/voltage input (selectable)

Hold input Minimum input signal width: 20 ms ---

External power supply 12 VDC (±10%), 100 mA

* Refer to Safety Precautions (Common) on page page 52 for details.

Control output Contact output: 3 A at 250 VAC/30 VDC, resistive load (cosφ=1)

Minimum applied load:10 mA at 5 VDC (failure level: P, reference value)

Display*2

7-segment, negative transmissive LCD

Character height

Present value: 10 mm (red), comparison value: 6 mm (green)

Digits 6 digits (0 to 999999)

Memory backup EEPROM (overwrites: 100,000 times min.) that can store data for 10 years min.

Operating temperature range −10 to 55°C (−10 to 50°C if Counter/Tachometers are mounted side by side) (with no icing or condensation)

Storage temperature range −25 to 70°C (with no icing or condensation)

Operating humidity range 25% to 85%

Case color Black (N1.5)

H7CX-R@-N

Characteristics

I/O Functions

* Refer to page page 50 for details on the hold function.

• The following table shows the delay from when the reset signal is

input until the output is turned OFF. (Reference values)

*See Life-test Curve (Reference Values) on the right.

Applicable Standards

*1. The following safety standards apply to the H7CX-R11@.

cUL (Listing): Applicable when an OMRON P2CF(-E) Socket is used.

cUR (Recognition): Applicable when any other socket is used.

*2. Industrial electromagnetic environment (EN/IEC 61326-1 Table 2)

Insulation resistance 100 MΩ min. (at 500 VDC) between current-carrying terminal and exposed non-

current-carrying metal parts, and between non-continuous contacts

Dielectric strength

2,000 VAC, 50/60 Hz for 1 min between current-carrying metal parts and non-current-

carrying metal parts

2,000 VAC (for 100 to 240 VAC), 50/60 Hz for 1 min between power supply and input

circuit (1,000 VAC for 24 VAC/12 to 24 VDC)

2,000 VAC 50/60 Hz for 1 min between control output, power supply, and input circuit

1,000 VAC, 50/60 Hz for 1 min between non-continuous contacts

Impulse withstand voltage

3.0 kV (between power terminals) for 100 to 240 VAC, 1.0 kV for 24 VAC/12 to 24 VDC

4.5 kV (between current-carrying terminal and exposed non-current-carrying metal

parts) for 100 to 240 VAC, 1.5 kV for 24 VAC/12 to 24 VDC

Noise immunity

±1.5 kV (between power terminals)

±600 V (between input terminals)

Square-wave noise by noise simulator (pulse width: 100 ns/1 μs, 1-ns rise)

Static immunity Destruction: 15 kV, Malfunction: 8 kV

Vibration

resistance

Destruction 10 to 55 Hz with 0.75-mm single amplitude, each in three directions for 2 hours

Malfunction 10 to 55 Hz with 0.35-mm single amplitude, each in three directions for 10 min

Shock re-

sistance

Destruction 300m/s2 each in three directions, three cycles

Malfunction 100m/s2 each in three directions, three cycles

Life expectancy

Mechanical: 10,000,000 operations min.

Electrical: 100,000 operations min. (3 A at 250 VAC, resistive load, ambient

temperature condition: 23°C) *

Weight Approx. 110 g (Tachometer only)

Approved

safety

standards

cULus (or cURus): UL508/CSA C22.2 No. 14 *1

Conforms to EN 61010-1 (IEC 61010-1): Pollution degree 2/overvoltage category II, B300 PILOT DUTY,

1/4 HP 120 VAC, 1/3 HP, 240 VAC, 3-A resistive load

EMC

(EMI)

Emission Enclosure:

Emission AC mains:

(EMS)

Immunity ESD:

Immunity RF-interference:

Immunity Conducted Disturbance:

Immunity Burst:

Immunity Surge:

Immunity Voltage Dip/Interruption:

EN61326-1 *2

EN55011 Group 1 classA

EN61326-1 *2

EN61000-4-2: 4 kV contact discharge (level 2);

8 kV air discharge (level 3)

EN61000-4-3: 10 V/m (Amplitude-modulated, 80 MHz to 1 GHz)

(level 3);

10 V/m (Pulse-modulated, 900 MHz ±5 MHz) (level 3)

EN61000-4-6: 10 V (0.15 to 80 MHz) (level 3)

EN61000-4-4: 2 kV power-line (level 3);

1 kV I/O signal-line (level 4)

EN61000-4-5: 1 kV line to lines (power and output lines) (level 2);

2 kV line to ground (power and output lines) (level 3)

EN61000-4-11: 0.5 cycle, 100% (rated voltage)

Life-test Curve

(Reference Values)

Resistive Load

Inductive Load

A current of 0.15 A max. can be switched at

125 VDC (cosφ=1) (Life expectancy: 100,000

operations)

A current of 0.1 A max. can be switched if

L/R=7 ms.

(Life expectancy: 100,000 operations)

1,000

700

500

300

100

Load current (A)

01 2 34

30 VDC (cosφ=1)

250 VAC (cosφ=1)

No. of operations ( ×10

)

1,000

700

500

300

100

01 2 34

30 VDC (L/R=7 ms)

Load current (A)

250 VAC (cosφ=1)

No. of operations ( ×10

)

Inputs

Count,

count 1,

count 2

Reads counting signals.

Hold • Holds the measurement value and outputs.

• The hold indicator is lit during hold.*

Outputs OUT Outputs signals according to the specified output

mode when a comparison value is reached.

Minimum reset signal width Output delay time

1 ms 0.8 to 1.2 ms

20 ms 15 to 25 ms

H7CX-R@-N

Connections

Terminal Arrangement

* The hold function is the same whichever terminal is connected. Terminals are not

connected internally, and so do not use them for cross-over wiring.

Block Diagram

Input Circuits

Count and Hold Inputs

OUT

0 V

(+)(−)

(−)

(+)

Sensor 12 VDC

External

power supply

Internal circuit

Count

Hold

H7CX-R11-N

H7CX-R11D1-N

OUT1

OUT2

0 V

(+)(−)

(−)

(+)

Sensor 12 VDC

External

power supply

Internal circui

Internal circuit

Count 1

Count 2

H7CX-R11W-N

H7CX-R11WD1-N

No-voltage Inputs

(NPN Inputs)

Voltage Inputs

(PNP Inputs)

Output circuit

Display circuit

Input circuits

(Basic insulation)

(Basic insulation) (Basic insulation)

Internal

control circuit

Power supply

circuit

Key switch

circuit

Internal

circuit

+14V

1 kΩ

Approx. 4.7 kΩInternal

circuit

H7CX-R@-N

Input Connections

The inputs of the H7CX-R are no-voltage (short-circuit or open) inputs or voltage inputs. They are set for use as voltage inputs at the time of

delivery.

No-voltage Inputs (NPN Inputs)

No-voltage Input Signal Levels

Note: The DC voltage must be 30 VDC max.

Voltage Inputs (PNP Inputs)

Voltage Input Signal Levels

Open Collector Voltage Output Contact Input DC Two-wire Sensor

H7CX-R11@3547 6

PLC or

sensor

0 V for inputs

Hold

Count

Note: Operates when the transistor turns ON.

H7CX-R11W@3 --- 6

Sensor,

etc.

0 V for inputs

Hold

Count

Note: Operates when the transistor turns ON.

H7CX-R11@3547 6

H7CX-R11W@3 --- 6

0 V for inputs

Hold

Count

Note: Operate when the contact turns ON.

H7CX-R11@

3547 6

H7CX-R11W@

3 --- 6

0 V for inputs

Hold

Count

Note: Operates when the transistor turns ON.

H7CX-R11@3547 6

H7CX-R11W@3 --- 6

No-contact

input

Short-circuit level (Transistor ON)

• Residual voltage: 3 V max.

• Impedance when ON: 1 kΩ max.

(The leakage current is approx. 12 mA when the impedance is 0 Ω.)

Open level (Transistor OFF)

• Impedance when OFF: 100 kΩ min.

Contact in-

put Use contacts which can adequately switch 5 mA at 10 V.

Applicable Two-wire Sensor

• Leakage current: 1.5 mA max.

• Switching capacity: 5 mA min.

• Residual voltage: 3 VDC max.

• Operating voltage: 10 VDC

No-contact Input (NPN Transistor) No-contact Input (PNP Transistor) Contact Input

Sensor,

etc.

0 V for inputs

Hold

Count

Note: Operate when the transistor turns OFF.

H7CX-R11@3547 6

H7CX-R11W@3 --- 6

Sensor,

etc.

0 V for inputs

Hold

Count

Note: Operate when the transistor turns ON.

H7CX-R11@3547 6

H7CX-R11W@3 --- 6

0 V for inputs

Hold

Count

Note: Operate when the contact turns ON.

H7CX-R11@3547 6

H7CX-R11W@3 --- 6

High level (Input ON): 4.5 to 30 VDC Note: 1. The DC voltage must be 30 VDC max.

2. Input resistance: Approx. 4.7 kΩ

Low level (Input OFF): 0 to 2 VDC

H7CX-R@-N

Nomenclature

Dimensions (Unit: mm)

Tachometers

(Factory setting)

(Enable)

(Factory setting) OFF

(Disable)

10 mm 6 mm

10 11

1. Hold Indicator (orange)

2. Key Protect Indicator (orange)

3. Control Output Indicator (orange)

4. Comparison Value 1, 2 Stage Indicator

(1-output models)

(2-output models)

Lit when the key protect switch is ON.

(Lit when the hold input or hold key is ON. )

7. Mode Key

(Used to switch mode and setting items.)

11. DIP Switch

1 6

5. Present Value (Main Display)

8. Hold Key

9. Up Keys to

Character height: 10 mm (red)

(Used to sustain the measurement value and output.)

6. Comparison Value (Sub-display)

Character height: 6 mm (green)

10. Key-protect Switch

1st digit

6th digit

Display Section Operation Keys

Switches

Character Size

for Sub-display

Character Size

for Main Display

OFF

12345678

OUT

OUT 1 2

63.7 14.4

44.8 × 44.8

48 × 48

Dimensions without Flush Mounting Adapter

H7CX-R@-N

Note: 1. The mounting panel thickness should be 1 to 5 mm.

2. To allow easier operation, it is recommended that

Adapters be mounted so that the gap between

sides with hooks is at least 15 mm (i.e., with the

panel cutouts separated by at least 60 mm).

3. It is possible to horizontally mount Timers side by

side. Attach the Flush Mounting Adapters so that

the surfaces without hooks are on the sides of the

Timers. If Counters/Tachometers are mounted side

by side, however, water resistance will be lost.

60 min.

15 min.

+0.6

−0

+0.6

−0

n side by side mounting

With Y92A-48F1 attached.

With Y92A-48 attached.

A=(48n−2.5) +1

−0

A=(51n−5.5) +1

−0

A={48n−2.5+(n−1)×4} +1

−0

Panel Cutouts

Panel cutouts are as shown below

(according to DIN43700).

48 89.97.5

Panel

(51)

Y92S-29 (order separately)

Waterproof Packing

Y92F-30 (order separately)

Flush Mounting Adapter

P3GA-11

(order

separately)

Rear Surface

Connection

Socket

Dimensions with Flush Mounting Adapter (Adapter and

Waterproof Packing Ordered Separately)

H7CX-R@-N

P2CF-11(-E) (order separately)

Front Connecting Socket

100.9

103.2*

Dimensions with Front Connecting Socket

H7CX-R@-N

* These dimensions vary with the kind of DIN track (reference value).

H7CX-R@-N

Accessories (Order Separately)

Soft Cover

Y92A-48F1

Protecting the Timer in Environments Subject to Oil

Hard Cover

Y92A-48

Order the Waterproof Packing separately if it is lost or damaged.

The Waterproof Packing can be used to achieve protection equivalent

to IP66.

(The Waterproof Packing will deteriorate, harden, and shrink

depending on the application environment. To ensure maintaining the

NEMA4 waterproof level, periodically replace the Waterproof

Packing. The periodic replacement period will depend on the

application environment. You must confirm the proper replacement

period. Use 1 year or less as a guideline. If the Waterproof Packing is

not replaced periodically, the waterproof level will not be maintained.)

It is not necessary to mount the Waterproof Packing if waterproof

construction is not required.

Connection Sockets

Refer to Connection Sockets on page page 13 for details.

Optional Products for Track Mounting

Refer to Optional Products for Track Mounting on page page 14 for details.

The H7CX's panel surface is water-resistive (conforming to IP@6,

UL Type 4X) and so even if drops of water penetrate the gaps

between the keys, there will be no adverse effect on internal circuits.

If, however, there is a possibility of oil being present on the

operator's hands, use the Soft Cover. The Soft Cover ensures

protection equivalent to IP54 against oil. Do not, however, use the

H7CX in locations where it would come in direct contact with oil.

Note: Depending on the operating environment, the condition

of resin or rubber products may deteriorate, or they may

shrink or become harder. Therefore, it is recommended

that resin products be replaced regularly.

Y92F-45

Use this Adapter to install the

Counter/Tachometer in a cutout

previously made for a DIN 72 × 72 mm

device (panel cutout: 68 × 68 mm).

Flush Mounting

Adapter

Y92F-30

Order a Flush Mounting Adapter

separately if the product is to be

flush-mounted.

Waterproof Packing

Y92S-29

H7CX-R@-N

Operating Procedures

Parameters must be set using both the DIP switch and the operation keys on the front panel.

Refer to the following for the detailed procedure.

• DIP switch settings are effective when the power is turned ON again. (Perform DIP switch settings while the power is OFF.)

The settings made using the DIP switch can be checked in the

DIP switch monitor mode.

OFF

Tachometer

AMD compatible

Tachometer

AMD compatible

Input mode*1

Counting speed/

Minimum input signal width

Output mode*2

Average processing

---

NPN/PNP input mode

--- ---

NPN PNP

30 Hz

10 ms

10 kHz*3

1 ms

OFF

Upper and lower limit

Area

Upper limit

Lower limit

OFF

OFF (no average processing)

2 times

4 times

8 times

Step1

Upper limit

Item OFF ON Counting speed/

minimum input signal width

Input mode Pin 2 Pin 1

Output mode Pin 4 Pin 6

Average processing Pin 6 Pin 5

Set the basic parameters.

Refer to the table on the right.

Note: The characters displayed in reverse video are the default settings.

Refer to the table on the right.

*1. The setting of Pin 1 is disabled (OFF) for the H7CX-R11W@.

*2. For the H7CX-R11W@.

Refer to the table on the right.

Output 1 mode

Output 2 mode

Note: The characters displayed in reverse video are the default settings.

OFF

Item OFF ON

Output mode Pin 4

Output mode

Pin 3

Lower limit

*3. For the H7CX-R11W@, the counting speed will be 5 kHz even if 10 kHz

is selected.

OFF

1 2 3 4 5 6 7 8

(Factory setting)

H7CX-R@-N

(99.9 s) (0.0 s)

(Enabled) (Disabled)

(99999) (0)

(19.99 s) (0.00 s)

(999999) (1)

(999.9 s) (0.1 s)

kp-1

off on

0 99999

0.00 19.99

999999 1

kp-2 kp-3 kp-4 kp-5 kp-6 kp-7

0 9999

Procedure for Models Other than “-R11W@” Models

Procedure for “-R11W@” Models

(9999 × 1000 times) (0 × 1000 times)

(KP-1) (KP-2) (KP-3) (KP-4) (KP-5) (KP-6) (KP-7)

Note: Not displayed in AMD-compatible mode.

*1 Set each digit using the individual U Key.

Note: The monitor value is only

displayed. It cannot be set.

Output OFF

delay

(OFFD)

Output ON

count alarm set

value/monitor

value

• Set each digit using the individual U Key.

Function Setting Mode

Auto-zero

time

(AUTO0)

Startup

time

(STMR)

Peak/bottom

hold

enabled

(DHLD)

Output

hysteresis

(HYS)

Set value

upper limit

(SL-H)

Key

protect

level

(KYPT)

• Set each digit using the individual U Key.

• Enable or disable peak/bottom hold using the U Key.

• Set the output hysteresis using the U Key.

• Set each digit using the individual U Key.

Note: The measurement value after prescaling is set.

• Set each digit using the individual U Key.

• Set the key protect level using the U Key.

Output

ON count

alarm set

value

Output

ON count

monitor

value

Output 1

(OUT1) ON

count alarm

set value

Output 2

(OUT2) ON

count alarm

set value

Note: The monitor value is only

displayed. It cannot be set.

Note: The monitor value is only

displayed. It cannot be set.

Output 1

(OUT1) ON

count

monitor

value

Output 2

(OUT2) ON

count

monitor

value

(9999 × 1000 times) (0 × 1000 times)

(MV) (SMP)

(99.999) (1.000) (0.001)

The characters displayed in reverse video are the default settings.

smp mv

Power ON

Run mode

Step2

Change to Function Setting Mode.

3 s min.*2

3 s min.*1

• Set the decimal point position using the U Key.

*1 If the mode is switched to the function setting mode during operation, operation will

continue.

*2 Changes made to settings in function setting mode are enabled for the first time when the

mode is changed to run mode.

Also, when settings are changed, the counter is reset (measured values initialized and

output turned OFF) on returning to run mode.

Function

setting mode

Averaging

method

(AUGT)

Prescale value

(PSCL)

Decimal point

position

(DP)

(No decimal point) (One digit after

decimal point)

(Two digits after

decimal point)

(Three digits after

decimal point)

• Set each digit using the individual U Key.

• Set the averaging method using the U Key.

Note: Not displayed in AMD-compatible mode.

Note: SMP: Simple averaging, MV: Moving average

For details on operations in run mode, refer to page page 47.

H7CX-R@-N

Explanation of Functions

Basic Functions

Input Mode

The mode can be switched between tachometer mode and AMD-

compatible mode.

Tachometer Mode

Use this mode to measure the pulse frequency (Hz).

AMD-compatible Mode

Use this mode to measure the pulse cycle (s).

Counting Speed

Set the maximum counting speed (30 Hz/10 kHz) for input. If contacts

are used for input signals, set the counting speed to 30 Hz.

Processing to eliminate chattering is performed for this setting.

Output Mode

Set the output method for control output based on the comparison

value.

Upper and lower limit (HI-LO), area (AREA), upper limit (HI), and

lower limit (LO) can be set. For the H7CX-RW@, the upper limit (HI-

HI) and lower limit (LO-LO) can be set. (For details on the operation

of the output modes, refer to Output Mode Settings on page page 49.)

Averaging Method (avgt)

Simple averaging (SMP) or a moving average (MV) can be selected

for the averaging method.

With a moving average, the average measurement value is displayed

every sampling cycle or pulse cycle, in contrast to simple averaging,

for which the average value is displayed for the set number of

samples.

Number of Averaging Times

Flickering display and output chattering can be prevented using

average processing. Average processing can be set to one of four

levels: no average processing, 2 times (i.e., the average of 2

measurement values), 4 times, or 8 times.

For a measurement frequency of 5 Hz or higher using a tachometer,

the average will be equal to the sampling cycle (200 ms) multiplied by

the averaging setting (i.e., the number of times).

For less than 5 Hz, the frequency will be measured when the input

pulse comes. Average processing produces a stable display even for

fluctuating input signals. Set the optimum number of times for the

application.

If AMD-compatible mode is used, the measurement cycle will be

measured when the input pulse is received. The output will change,

however, when the comparison value is exceeded even if averaging

is enabled.

NPN/PNP Input Mode

Select either NPN input (no-voltage input) or PNP input (voltage

input) as the input format. When using a two-wire sensor, select NPN

input.

The same setting is used for all external inputs.

For details on input connections, refer to Input Connections on page

page 40.

Advanced Functions

Decimal Point Position (dp)

Decide the decimal point position for the measurement value and

comparison value.

Prescale Value (pscl)

It is possible to display the rate of rotation or the speed of a device or

machine to which the H7CX is mounted by converting input pulses to

a desired unit.

If the default prescaling value (1,000) is used, the input frequency

(Hz) will be displayed.

The relationship between display and input is determined by the

following equation. Set the prescale value according to the unit to be

displayed.

Displayed value = f × α

f: Input pulse frequency (number of pulses in 1 second)

α: Prescale value

(1) Displaying Rotation Rate

N: Number of pulses per revolution

Example: In order to display the rate of rotation for a machine that

outputs 5 pulses per revolution in the form @@.@ rpm:

1. Set the decimal point position to 1 decimal places.

2. Using the formula, set the prescale value (α) to

1/N × 60 = 60/5 = 12.

(2) Displaying Speed

N: Number of pulses per revolution

d: Diameter of rotating body (m)

πd: Circumference (m)

• Observe the following points when

setting a prescale value.

Set the set value to a value less than {Maximum countable value

− Prescale value}.

Example: If the prescale value is 1.25 and the counting range is

0.000 to 999.999, set the set value to a value less than 998.749

(= 999.999 − 1.25).

If the set value is set to a value greater than this, output will not turn

ON.

Auto-zero Time (auto0)

It is possible to make the settings so that the frequency will be force-

set to 0 if there is no pulse for a specified period of time. This time is

called the auto-zero time.

Cycle (s)

Display unit Prescale value (α)

rpm 1/N × 60

rps 1/N

Display unit Prescale value (α)

m/min πd × 1/N × 60

m/s πd × 1/N

d: Diameter

of rotating

body (m)

Note: If the prescale value setting is incorrect, a counting error will

occur. Check that the settings are correct before using this

function.

Note: Set the auto-zero time to a time slightly longer than the

estimated interval between input pulses. It will not be

possible to make accurate measurements if the auto-zero

time is set to a time shorter than the input pulse cycle.

Setting a time that is too long may also result in problems,

such as a time-lag between rotation stopping and the

alarm turning ON.

H7CX-R@-N

Startup Time (stmr)

In order to prevent undesired output resulting from unstable input

immediately after the power supply is turned ON, measurement can

be prohibited for a set time at startup.

It can also be used to stop measurement and disable output until the

rotating body reaches the normal rate of rotation, after the power

supply to the H7CX and rotating body are turned ON at the same time.

Peak/bottom Hold Enabled (dhld)

This function records the peak and bottom (i.e., minimum) values

after counting starts (after turning ON the power supply or changing

the configuration selection mode or function setting).

The peak value is also held when the power supply is interrupted.

Output Hysteresis (hys)

This setting can be used to prevent output chattering if the

measurement value fluctuates slightly near the set value.

In Thachometer Mode, the measurement value after prescaling is set.

Output OFF Delay (offd)

This function delays the timing for turning OFF comparative output by

a certain time.

The ON time can be held for the set time if the comparative result

changes in a short time.

Operation will continue and outputs will not change while holding the

value.

Set Value Upper Limit (sl-h)

Set the upper limit for the set value when it is set in run mode.

Key Protect Level (ypt)

Set the key protect level.

Refer to Key Protect Level on page page 48.

Output ON Count Alarm Set Value (on-a)

Set the alarm value for the output ON count.

The limit can be set to between 0 × 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of the output exceeds the alarm set value, e3

will be displayed on the Timer to indicate that the output ON count

alarm value was exceeded. Refer to Self-diagnostic Function on page

page 48 for information on the e3 display.

ON Count Alarm Set Values for Outputs 1 and 2 (OUT1

and OUT2) (on1a and on2a)

Set the ON count alarm values for the outputs 1 and 2.

The limit can be set to between 0 × 1000 (0 times) and 9999 × 1000

(9,999,000 times). Only the underlined values are set. The alarm will

be disabled if 0 is set.

If the total ON count of instantaneous output 1 or 2 exceeds the alarm

set value, e3 will be displayed on the Timer to indicate that the output

ON count alarm value was exceeded. Refer to Self-diagnostic

Function on page page 48 for information on the e3 display.

Output ON Count Monitor Value (on-c)

The monitor value is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

ON Count Monitor Values for Outputs 1 and 2 (OUT1 and

OUT2) (on1c and on2c)

The monitor value for output 1 or 2 is only displayed. It cannot be set.

The output ON count will be 1,000 times the displayed value.

Startup timeDisplay

Time

Comparison value

(lower limit)

Output

(lower limit)

Power supply

OUTX1

OUTY2

Display value

Comparison value 2 Hysteresis

Hysteresis

Comparison value 1

Set the hysteresis for when

the output turns OFF.

H7CX-R@-N

Operation in Run Mode

Output Mode: HI or LO Output Mode: HI-LO or AREA

H7CX-R11@-N

H7CX-R11W@-N

Displayed for Models Other Than “-W” Models Displayed for “-W” Models

Measurement value

Comparison value

Bottom hold value

Peak hold value

Bottom hold value 1

Peak hold value 2

Bottom hold value 2

Peak hold value 1

Measurement value

Comparison value 1

Measurement value

Comparison value 2

Measurement value 1

Measurement value 2

Comparison value 1

Comparison value 2

• Set each digit using the individual U Keys.

• Measurement Value

Displays the currently measured value.

• Comparison Value, Comparison Value 1, and

Comparison Value 2

Set the comparison value, comparison value 1,

and comparison value 2.

The measurement value is compared to

comparison value, comparison value 1, and

comparison value 2 and an output is made

according to the selected output mode.

*1 Peak/bottom hold enabled

• Peak/bottom hold value

The peak (maximum) and bottom (minimum)

values are displayed after counting starts.

• Peak/bottom hold value 2

Peaks (maximums) 1 and 2 and bottoms

(minimums) 1 and 2 are displayed after counting

starts.

Note: The held values will be initialized when the

Hold Key or reset 1 input is turned OFF

while peak/bottom hold values 1 and 2 are

being displayed.(The reset 2 input

operates in the same way if the input

mode is set to 2-input mode.)

H7CX-R@-N

Key Protect Level

When the key-protect switch is set to ON, it is possible to prevent setting errors by prohibiting the use of certain operation keys by specifying the

key protect level (KP-1 to KP-7). The key protect level is set in the function setting mode. The key protect indicator is lit when the key-protect switch

is ON.

* Changing mode to DIP switch monitor mode or function setting mode.

Self-diagnostic Function

The following displays will appear if an error occurs.

*1. This includes times when the life of the EEPROM has expired.

*2. Occurs when the measurement value reaches 999,999.

*3. Display flashes (1-second cycles).

*4. The normal display and e3 will appear alternately.

When the Hold Key is pressed, e3 will not be displayed even if the alarm set value is exceeded. (Monitoring is possible, however, because the counter will continue

without clearing the output ON count.)

Level Meaning

Details

Changing mode* Switching display

during operation Hold Key Up Key

KP-1

(default setting) Invalid Valid Valid Valid

KP-2 Invalid Valid Invalid Valid

KP-3 Invalid Valid Valid Invalid

KP-4 Invalid Valid Invalid Invalid

KP-5 Invalid Invalid Invalid Invalid

KP-6 Invalid Invalid Valid Valid

KP-7 Invalid Invalid Invalid Valid

Main display Sub-display Error Output status Correction method Set value after

reset

ffffff *3 No change Measurement value overflow*2 No change Measurement value ≤ 999999 No change

e1 Not lit CPU OFF Either press the hold key or reset the

power supply. No change

e2 Not lit Memory error (RAM) OFF Turn ON the power again. No change

e2 sum Memory error (EEP)*1 OFF Hold Key Factory setting

e3 *4 No change Output Counter Overflow No change Hold Key No change

Key protect indicator

*Factory-set to OFF

(Enable)

OFF

(Disable)

H7CX-R@-N

Output Mode Settings

Models Other Than H7CX-R11W@ in Tachometer Mode Models Other Than H7CX-R11W@ in AMD-compatible

Mode

Note: If time “a” is exceeded during operation, the output will turn ON. If time “b” is

exceeded during operation, the output will turn OFF. (If average processing is

enabled, the output operation will be performed when the time is exceeded once.)

H7CX-R11W@

Output mode

setting Operation

Upper and

lower limit

ON condition: Measurement value ≤ Comparison value 1 or

Measurement value ≥ Comparison value 2

Note: When comparison value 1 ≥ Comparison value 2, the output

isalways ON regardless of the comparison value.

Area

Upper limit

ON condition: Measurement value ≥ Comparison value

Lower limit

ON condition: Measurement value ≤ Comparison value

OUT

Measurement

value

Comparison value 2

(Upper-limit)

Comparison value 1

(Lower-limit)

Condi-

tion

Comparison value 1 ≤

Comparison value 2

Comparison value 1 >

Comparison value 2

ON con-

dition

Comparison value 1 ≤

measurement value

≤

Comparison value 2

Comparison value 2 ≤

measurement value

≤

Comparison value 1

OUT

Measurement

value

Comparison

value 2

Comparison

value 1

OUT

Comparison value

(Upper-limit)

Measurement value

OUT

Measurement value

Comparison value

(Lower-limit)

Output mode

setting Operation

Upper and

lower limit

ON condition: Measurement value < Comparison value 1 or

Measurement value ≥ Comparison value 2

Note: When comparison value 1 ≥ comparison value 2, the output

isalways ON regardless of the comparison value.

Area

Upper limit

ON condition: Measurement value ≥ Comparison value

Lower limit

ON condition: Measurement value < Comparison value

OUT

Measurement

value

Comparison value 2

(Upper-limit)

Comparison value 1

(Lower-limit)

Condi-

tion

Comparison value 1 ≤

Comparison value 2

Comparison value 1 >

Comparison value 2

ON con-

dition

Comparison value 1 ≤

measurement value

Comparison value 2

Comparison value 2 ≤

measurement value

Comparison value 1

OUT

Measurement

value

Comparison

value 2

Comparison

value 1

OUT

Comparison value

(Upper-limit)

Measurement value

Comparison value

(Lower-limit)

OUT

Output mode

setting Operation

Upper limit

(HI)

Lower limit

(LO)

OUT1

CP1 display

value

Comparison

value 1

OUT2

CP2 display

value

Comparison

value 2

ON condition for output 1: CP1 present value (display value) ≥ Comparison value 1

ON condition for output 2: CP2 present value (display value) ≥ Comparison value 2

Output 1 Output 2

OUT1

CP1

display value

Comparison

value 1

OUT2

CP2

display value

Comparison

value 2

ON condition for output 1: CP1 present value (display value) ≤ Comparison value 1

ON condition for output 2: CP2 present value (display value) ≤ Comparison value 2

Output 1 Output 2

H7CX-R@-N

Precautions for the H7CX-R

In upper and lower limit output mode, if the comparison value setting is such that comparison value 1 ≥ comparison value 2, the output will always

be ON.

Hold Function

The measurement value (display value) and output are sustained while the hold input is ON.

Note: The output will maintain the current status when the hold key is pressed.

Example:

* The H7CX-R11W@-N does not have a hold input.

Operation in DIP Switch Monitor Mode

The H7CX-R is also equipped with a DIP switch monitor function, a convenient function that enables the settings of the DIP switch pins to be

confirmed using the front display.

Output mode

setting Operation

Lower limit

OUT

Display value

Hold input* (Hold Key)

Comparison value (lower limit)

Sustained display value

Sustained output

Actual input

Convenient

: Measurement stopped

: Measurement possible

Key

1 s min.

Power ON

DIP switch monitor

Run Mode

DIP Switch

Monitor

Mode

…Indicates that DIP switch pin 8 is ON.

…Indicates that DIP switch pin 7 is OFF.

…Indicates that DIP switch pin 6 is ON.

…Indicates that DIP switch pin 5 is OFF.

…Indicates that DIP switch pin 4 is ON.

…Indicates that DIP switch pin 3 is OFF.

…Indicates that DIP switch pin 2 is ON.

…Indicates that DIP switch pin 1 is OFF.

Example

OFF

12345678

The status of the DIP switch pins (1 to 8) can be confirmed using the U Key.

* When the mode is changed to DIP switch monitor, the measurement value is reset, outputs turns OFF, and

measuring stops.

Note: To change the mode to DIP switch monitor mode, press the Key

for 1 s min. with the Key held down. The mode will not change

if the Key is pressed first.

H7CX-R@-N

Precautions on Replacing the AMD-S

Terminal Arrangement and Wiring Connections

Note: 1. Wiring must be changed from an 8-pin socket to an 11-pin socket.

2. Take into consideration the length of the wires and the terminal numbers.

3. Order the P2CF-11Connecting Socket separately.

Setting Procedure

Perform the following settings to achieve the functions of the AMD-S

using the H7CX-R11-N.

DIP Switch Settings

Note: The characters displayed in reverse video are the default

settings.

* Refer to page page 43 for information on DIP switch settings.

Operation Key Settings

Note: The characters displayed in reverse video are the default

settings.

Characteristics

* When set to AMD mode.

The H7CX-R11-N is the recommended model for replacing the AMD-S-series Motion Detector. Refer to the following precautions before

replacing the AMD-S.

AMD-S H7CX-R11-N

3456

2187

Sensor

Tc Ta

Relay output

100/110 VAC

(200/220 VAC)

8PFA

Black (white)

Brown (red)

Blue (black)

• Connection Sockets: 8PFA

678

11110

HOLD HOLD

Tb Ta

Relay output

100 to 240 VAC

P2CF-11

Black (white)

Brown (red)

Blue

(black)

Sensor

• Connection Sockets: P2CF-11

Model

AMD-S

H7CX-R11-N

Item DIP switch pin status * Set

value

Measuring

ranges

0.01 to 0.1 s

(AMD-S@1), 0.1

to 1 s (AMD-

S@2), 1 to 10 s

(AMD-S@3)

Set DIP switch pin 1 to ON for

AMD-compatible mode. 1 ms

10 ms

Output

mode

Rotation

increase

detection

(AMD-SU@)

Rotation

decrease

detection

(AMD-SL@)

Average

process-

ing

None

Input

mode Voltage Input

OFF

12345678

OFF

AMD compatible

10 ms

1 ms

Counting Speed /

Minimum input signal width

Input

mode

Pin 2Pin 1

OFF

12345678

Lower

limit

OFF

12345678

Upper

limit

OFF

12345678

OFF

12345678

PNP

Model

AMD-S

H7CX-R11-N

Item Parameter

sSetting range Set

value

Startup

time Fixed (0.1 to 10 s)

Model AMD-S H7CX-R11-N

Item

Supply voltage −100 to 110 VAC

−200 to 220 VAC −100 to 240 VAC

Input method Voltage input (high: 4 to 14

V, low: 0 to 1 V)

No-voltage input/voltage

input (high: 4.5 to 30 V, low:

0 to 2 V)

External pow-

er supply 12 VDC ±1 V, 12 mA 12 VDC (±10%), 100 mA

Relay output 5 A at 200 VAC (resistive

load)

3 A at 250 VAC/30 VDC

(resistive load)

Output mode

Rotation increase (AMD-

SU@)

Rotation decrease (AMD-

SL@)

HI-LO, AREA, HI-HI, LO-LO

(Set using DIP switch.)

Setting meth-

od Input pulse interval (s) Input pulse interval (s) *

Detection rota-

tion rate range

6 to 6,000 rpm

(for 1 pulse/rotation)

0.00006 to 20,000 rpm *

(for 1 pulse/rotation)

Startup time

Always from 0.1 to 10 s

(Always 10 s if not

specified.)

Setting range: 0.0 to 99.9 s

Life expectan-

Output relay electrical

operations of 500,000 min.

Output relay electrical

operations of 100,000 min.

Memory back-

up None EEPROM (overwrites:

100,000 times min.)

stmr

(STMR)

(99.9 s)(0.0 s)

H7CX-@-N

Safety Precautions for All H7CX Series (Common)

Do not allow pieces of metal, wire clippings, or fine

metallic shavings or fillings from installation to enter

the product. Doing so may occasionally result in

electric shock, fire, or malfunction.

Minor injury due to explosion may occasionally occur.

Do not use the Counter where subject to flammable or

explosive gas.

Fire may occasionally occur. Tighten the terminal

screws to the rated torque.

H7CX terminals: 6.55 to 7.97 lb-in (0.74 to 0.90 N·m)

P2CF Socket terminals: 4.4 lb-in (0.5 N·m)

Minor injury due to electric shock may occasionally

occur. Do not touch any of the terminals while power

is being supplied. Be sure to mount the terminal cover

after wiring.

The life expectancy of the output relay varies

considerably according to its usage. Use the output

relay within its rated load and electrical life

expectancy. If the output relay is used beyond its life

expectancy, its contacts may become fused or there may be a

risk of fire. Also, be sure that the load current does not exceed

the rated load current and when using a heater, be sure to use a

thermal switch in the load circuit.

Minor electric shock, fire, or malfunction may

occasionally occur. Do not disassemble, modify, or

repair the Counter or touch internal components.

• The panel surface of the H7CX-A/-R is water-resistant (conforming

to NEMA4, IP66, UL Type 4X (Indoor Use Only). To protect the

internal circuits from water penetration through the space between

the H7CX and operating panel, waterproof packing is included.

Attach the Y92F-30 Adapter with sufficient pressure with the

reinforcing screws so that water does not penetrate the panel.

• When mounting the Counter to a panel, tighten the two mounting

screws alternately, a little at a time, so as to keep them at an equal

tightness. If the panel screws are tightened unequally, water may

enter the panel.

• Store the Counter at the specified temperature. If the Counter has

been stored at a temperature of less than

−10°C, allow the Counter to stand at room temperature for at least

3 hours before use.

• Mounting the Counter side-by-side may reduce the life

expectancies of internal components.

• Use the Counter within the specified ranges for the ambient

operating temperature and humidity.

• Do not use in the following locations:

• Locations subject to sudden or extreme changes in temperature.

• Locations where high humidity may result in condensation.

• Do not use the Counter outside of the rated ranges for vibration,

shock, water exposure, and oil exposure.

• Do not use this Counter in dusty environments, in locations where

corrosive gasses are present, or in locations subject to direct

sunlight.

• Install the Counter well away from any sources of static electricity,

such as pipes transporting molding materials, powders, or liquids.

• Internal elements may be destroyed if a voltage outside the rated

voltage range is applied.

• Be sure that polarity is correct when wiring the terminals.

• Separate the Counter from sources of noise, such as devices with

input signals from power lines carrying noise, and wiring for I/O

signals.

• Do not connect more than two crimp terminals to the same

terminal.

• Up to two wires of the same size and type can be inserted into a

single terminals.

• Use the specified wires for wiring. Applicable Wires: AWG 18 to

AWG 22, solid or twisted, copper

• Install a switch or circuit breaker that allows the operator to

immediately turn OFF the power, and label it to clearly indicate its

function.

• When the Counter is operated with no-voltage input (NPN input),

approximately 14 V is output from the input terminals. Use a sensor

that contains a diode.

• Use a switch, relay, or other contact so that the rated power supply

voltage will be reached within 0.1 seconds. If the power supply

voltage is not reached quickly enough, the Counter may

malfunction or outputs may be unstable.

• Use a switch, relay, or other contact to turn the power supply OFF

instantaneously. Outputs may malfunction and memory errors may

occur if the power supply voltage is decreased gradually.

• When changing the set value during operation, because the H7CX

uses a constant read-in system, output will turn ON if the set value

is equal to the present value.

• When changing the comparison value during operation, because

the H7CX uses a constant read-in system, the output status will

change if the comparison value is changed to a value on the other

side of the present value. (when using as a tachometer)

• If the set value and present value are both 0, the output will turn

ON for the default setting. The output will turn OFF during a reset

operation. (when using as a counter)

• When the power is turned ON using the factory settings, the output

will turn ON after 999.9 s if no pulses are received as count input.

• Do not use organic solvents (such as paint thinners or benzine),

strong alkali, or strong acids. They will damage the external finish.

• Confirm that indications are working normally, including the

backlight LED, and LCD. The indicator LEDs, LCD, and resin parts

may deteriorate more quickly depending on the application

environment, preventing normal indications. Periodic inspection

and replacement are required.

• The waterproof packing may deteriorate, shrink, or harden

depending on the application environment. Periodic inspection and

replacement are required.

CAUTION

Precautions for Safe Use

0.5 to 1 mm

It is recommended that the

space between the screw

head and the Adapter be

0.5 to 1 mm.

Input0 V

Sensor

Diode

H7CX-@-N

• H7CX models with a 12 to 24-VDC power supply use a

transformer-free power supply method in which the power supply

terminals are not isolated from the signal input terminals. If a non-

isolating DC power supply is used, unwanted current paths may

occasionally burn or destroy internal components depending on

the wiring. Always check the wiring sufficiently before use.

• An inrush current of approx. 10 A will flow for a short time when the

power supply is turned ON. If the capacity of the power supply is

not sufficient, the Counter may not start. Be sure to use a power

supply with sufficient capacity.

• Maintain voltage fluctuations in the power supply within the

specified operating voltage range.

• When turning the power ON and OFF, input signal reception is

possible, unstable, or impossible as shown in the diagram below.

• Inrush current generated by turning ON or OFF the power supply

may deteriorate contacts on the power supply circuit. Turn ON or

OFF to a device with the rated current of more than 10 A.

• The capacity of the external power supply is 100 mA at 12 V. When

using a 24 VAC/12 to 24 VDC power supply, reduce the load with

the power supply voltage, as shown in the following diagram (DC

power supplies only).

• If the prescale value setting is incorrect, a counting error will occur.

Check that the settings are correct before using this function.

• Make sure that all settings are appropriate for the application.

Unexpected operation resulting in property damage or accidents

may occur if the settings are not appropriate.

• Do not leave the Counter for long periods at a high temperature

with output current in the ON state. Doing so may result in the

premature deterioration of internal components (e.g., electrolytic

capacitors).

• EEPROM is used as backup memory when the power is

interrupted. The write life of the EEPROM is 100,000 writes. The

EEPROM is written at the following times:

• When the power supply is turned OFF

• When switching from Configuration Selection Mode or Function

Setting Mode to Run Mode

• Dispose of the product according to local ordinances as they apply.

• Attach the front panel when using the Counter. The tabs in the

middle of each of four sides secure the front panel to the main

body. To remove the panel, widen the four tabs and pull the panel

toward you.

To mount the panel, fit all four tabs correctly into the grooves on the

main body.

• When conforming to EMC standards, refer to the information

provided in this datasheet for cable selection and other conditions.

• This is a class A product. In residential areas it may cause radio

interference, in which case the user may be required to take

adequate measures to reduce interference.

•H7CX-A@-N: Basic insulation is provided between power supply

and input terminals, between power supply and output terminals,

and between input and output terminals. (However, no insulation is

provided between the power supply and input terminals for the

H7CX-A@D-N.)

•H7CX-R@-N: Basic insulation is provided between power supply

and input terminals and between input and output terminals.

• When double insulation or reinforced insulation is required, apply

double insulation or reinforced insulation as defined in IEC 60664

that is suitable for the maximum operating voltage with clearances

or solid insulation.

• Connect the input and output terminals to devices that do not have

any exposed charged parts.

Precautions for Correct Use

Input Impossible

200 ms 5 ms0 to 90 ms 0 to 1 s

Possible

Unstable

Impossible

Power

supply

OFF

Power supply voltage (VDC)

10.8 15

100

Load current (mA)

Conformance to EN/IEC Standards

Ta b s

Grooves

MEMO

Warranty and Application Considerations

Read and Understand This Catalog

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have

any questions or comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or

other period if specified) from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,

MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER

ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET

THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR

IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS,

OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON

CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE

PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED,

INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE

MODIFICATION OR REPAIR.

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of

products in the customer's application or use of the products.

Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will

be used.

Know and observe all prohibitions of use applicable to this product.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT

ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON

PRODUCTS ARE PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR

SYSTEM.

Disclaimers

PERFORMANCE DATA

Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a

warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application

requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with

your OMRON representative at any time to confirm actual specifications of purchased product.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Authorized Distributor:

In the interest of product improvement,

specifications are subject to change without notice.

Cat. No. M079-E1-01

Printed in Japan

0709

OMRON Corporation Industrial Automation Company

OMRON ELECTRONICS LLC

One Commerce Drive Schaumburg,

IL 60173-5302 U.S.A.

Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

Regional Headquarters

OMRON EUROPE B.V.

Wegalaan 67-69-2132 JD Hoofddorp

The Netherlands

Tel: (31)2356-81-300/Fax: (31)2356-81-388

Contact: www.ia.omron.com

Tokyo, JAPAN

OMRON ASIA PACIFIC PTE. LTD.

No. 438A Alexandra Road # 05-05/08 (Lobby 2),

Alexandra Technopark,

Singapore 119967

Tel: (65) 6835-3011/Fax: (65) 6835-2711

OMRON (CHINA) CO., LTD.

Room 2211, Bank of China Tower,

200 Yin Cheng Zhong Road,

PuDong New Area, Shanghai, 200120, China

Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200

CSM_12_4_0716