OUTPUT SPECIFICATIONS
Voltage adjustability See Note 3 ±10%
Line regulation LL to HL, all outputs ±0.1%
Load regulation ML to FL
Single outputs ±0.1%
Dual outputs ±1.0%
Cross regulation Asymmetrical load 5.0% max.
25% / 100% FL
Voltage accuracy ±2.0%
Minimum load 2.1V, 3.3V, 5V 50mA max.
Single 12V, 15V 80mA max.
Duals: each output 10% FL
Overshoot At start-up 3.0% max.
Ripple and noise 20MHz bandwidth 1.5% pk-pk, max.
20mV rms
Transient response 25% load step ±10% typ. max. dev.,
0.5ms recovery
to within ±1.0%
Temperature coefficient ±0.02%/°C
Short circuit protection Hiccup mode Continuous
See Note 5 automatic recovery
INPUT SPECIFICATIONS
Input voltage range 5VDC, nominal, FL 4.5 to 9VDC
12VDC nominal, FL 9 to 18VDC
24VDC nominal, FL 18 to 36VDC
48VDC nominal, FL 36 to 72VDC
Input filter Pi filter
Input current See table
Input reflected ripple Single output 200mA
Dual outputs 200mA
Start-up time 500ms
MHP10 SERIES
Single and dual output
[ 2 YEAR WARRANTY ]
• 2 x 1 x 0.4 inch package
• 12.5 Watts/in3power density
• 32 models including 3.3VDC and 2.1VDC
• Designed to meet EN60950
• Indefinite short circuit protection
• Optional remote ON/OFF
• Optional trim output
The MHP10 series of DC/DC converters, comprising 32 different models, has
been designed for a wide range of applications including communications,
industrial systems and mobile battery powered systems. Packing 10 Watts of
power into a 2 x 1 x 0.4 inch package, with efficiencies as high as 80% the
MHP10 has wide input ranges of 4.5-9VDC, 9-18VDC, 18-36VDC and 36-
72VDC and is available in both single and dual output versions. Other features
include indefinite short circuit protection with automatic recovery and remote
on/off, all of which minimize the need for external circuitry and make the MHP10
a recommended component in distributed power systems.
SPECIFICATION
All specifications are typical at nominal input, full load at 25°C unless otherwise stated
PAGE 1
INPUT SPECIFICATIONS CONTINUED
Remote ON/OFF
Logic compatibility CMOS/TTL, See Note 4
ON 3.5VDC min. or open
OFF 0.8VDC max.
GENERAL SPECIFICATIONS
Efficiency 78% typ.
Isolation voltage Input/output 500VDC
Isolation capacitance Input/output 1nF
Switching frequency Fixed 200 to 275kHz
Approvals and Safety VDE0805, EN60950, IEC950
standards (pending) UL1950, CSA C22.2 No. 950
Case material Black coated, metal case
Material flammability UL94V-0
Weight 27g (0.95oz)
MTBF MIL-HDBK-217F 300,000 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance Operating ambient -25°C to +60°C
(See derating curve)
Extended temp., -40°C to +60°C
option, See Note 1
Non-operating amb. -40°C to +95°C
Case +95°C max.
Derating See derating curve
Cooling Free air convection cooled
Relative humidity Non-condensing 30% to 95%
Altitude Operating 10,000 feet max.
Non operating 40,000 feet max.
Vibration 5Hz to 500Hz 2.5G rms (approx.)
INPUT OUTPUT OUTPUT INPUT TYPICAL REGULATION (TYP.) MODEL NUMBER
VOLTAGE VOLTAGE CURRENT CURRENT EFFICIENCY LINE LOAD
4.5-9VDC 2.1V 2000mA 1400mA 60% ±0.1% ±0.1% MHP10-05S2V1 (2)
4.5-9VDC 3.3V 2000mA 2095mA 63% ±0.1% ±0.1% MHP10-0533V3 (2)
4.5-9VDC 5.0V 1400mA 2058mA 62% ±0.1% ±0.1% MHP10-05S05 (2)
4.5-9VDC 12V 580mA 1856mA 75% ±0.1% ±0.1% MHP10-05S12 (2)
4.5-9VDC 15V 460mA 1769mA 78% ±0.1% ±0.1% MHP10-05S15 (2)
4.5-9VDC ±5.0V ±600mA 1764mA 68% ±0.1% ±1.0% MHP10-05D05 (2)
4.5-9VDC ±12V ±290mA 1784mA 78% ±0.1% ±1.0% MHP10-05D12 (2)
4.5-9VDC ±15V ±230mA 1769mA 78% ±0.1% ±1.0% MHP10-05D15 (2)
9-18VDC 2.1V 2000mA 583mA 60% ±0.1% ±0.1% MHP10-12S2V1
9-18VDC 3.3V 2000mA 753mA 73% ±0.1% ±0.1% MHP10-12S3V3
9-18VDC 5.0V 2000mA 1068mA 78% ±0.1% ±0.1% MHP10-12S05
9-18VDC 12V 800mA 1025mA 78% ±0.1% ±0.1% MHP10-12S12
9-18VDC 15V 660mA 1068mA 78% ±0.1% ±0.1% MHP10-12S15
9-18VDC ±5.0V ±600mA 704mA 71% ±0.1% ±1.0% MHP10-12D05
9-18VDC ±12V ±400mA 1025mA 78% ±0.1% ±1.0% MHP10-12D12
9-18VDC ±15V ±300mA 1068mA 78% ±0.1% ±1.0% MHP10-12D15
18-36VDC 2.1V 2000mA 291mA 60% ±0.1% ±0.1% MHP10-24S2V1
18-36VDC 3.3V 2000mA 376mA 73% ±0.1% ±0.1% MHP10-24S3V3
18-36VDC 5.0V 2000mA 534mA 78% ±0.1% ±0.1% MHP10-24S05
18-36VDC 12V 800mA 512mA 78% ±0.1% ±0.1% MHP10-24S12
18-36VDC 15V 660mA 528mA 78% ±0.1% ±0.1% MHP10-24S15
18-36VDC ±5.0V ±600mA 347mA 71% ±0.1% ±1.0% MHP10-24D05
18-36VDC ±12V ±400mA 512mA 78% ±0.1% ±1.0% MHP10-24D12
18-36VDC ±15V ±300mA 528mA 78% ±0.1% ±1.0% MHP10-24D15
36-72VDC 2.1V 2000mA 145mA 60% ±0.1% ±0.1% MHP10-48S2V1
36-72VDC 3.3V 2000mA 180mA 73% ±0.1% ±0.1% MHP10-483V3
36-72VDC 5.0V 2000mA 267mA 78% ±0.1% ±0.1% MHP10-48S05
36-72VDC 12V 800mA 256mA 78% ±0.1% ±0.1% MHP10-48S12
36-72VDC 15V 660mA 264mA 78% ±0.1% ±0.1% MHP10-48S15
36-72VDC ±5.0V ±600mA 176mA 77% ±0.1% ±1.0% MHP10-48D05
36-72VDC ±12V ±400mA 256mA 78% ±0.1% ±1.0% MHP10-48D12
36-72VDC ±15V ±300mA 264mA 78% ±0.1% ±1.0% MHP10-48D15
Output Power (%)
0%
0°C20°C 40°C 60°C 80°C 100°C 120°C
-25°C
90°C
DERATING CURVE
Output Power (Watts)
60°C
100%
Ambient Temperature (°C)
Notes
1 Extended operating temperature range is available as an option. To
specify a MHP10 that operates down to -40°C, add the suffix ‘-4’ to the
model number, e.g. MHP10-24S05-4.
2 5VDC input, max. 7 Watt output power.
3 External trimming of the output voltage is optional on the single output
units, add the suffix ‘-T’ to the end of the model number,
e.g. MHP10-05S05-T.
4 Remote on/off is available as an option, add the suffix ‘-S’ to the end of
the model number, e.g. MHP10-24D15-S.
5 5VDC in max. for 1 minute.
10 Watt
Wide input DC/DC converters
DC/DC CONVERTERS |
10W DC/DC
PAGE 2
http://www.artesyn.com
BOTTOM VIEW
Ø 0.04 Dia.
(1.02)
0.24
(6.10)
0.80
(20.30)
2.00
(50.80)
ALL DIMENSIONS IN INCHES (mm)
Tolerance : ±0.008 (0.2) max. on pin placement
±0.02 (0.5) max. on outer dimensions
54 3
0.40
(10.20)
1.00
(25.40)
0.30
(7.60)
0.40
(10.16)
621
0.60
(15.20)
0.60
(15.20)
0.40
(10.20)
0.10
(2.50) 0.10
(2.50)
0.20
(5.10)
0.40
(10.20) 0.40
(10.20)
DC/DC CONVERTERS |
10W DC
PAGE 3
10 Watt
Wide input DC/DC converters
10W DC/DC
|DC/DC CONVERTERS
10KΩ
TRIMPOT
TRIM
UP
TRIM
DOWN
5
4
3
5
4
3
PIN CONNECTIONS
PIN NUMBER SINGLE OUTPUTS DUAL OUTPUT
1 + Input + Input
2 - Input - Input
3 + Output + Output
4 N.C./Trim (Option) Common
5 - Output - Output
6 Control (Option) Control (Option)
EXTERNAL OUTPUT TRIMMING
Single output models can be externally trimmed
by ±10% using either method shown below.
DS_MHP10_19980401.PDF
