DS1487 DS1487 Low Power RS-485 1/4 Unit Load Multipoint Transceiver Literature Number: SNLS132 DS1487 Low Power RS-485 14 Unit Load Multipoint Transceiver General Description Features The DS1487 is a low-power transceiver for RS-485 and RS-422 communication. The device contains one driver and one receiver. The drivers slew rate allows for operation up to 2.0 Mbps (see Applications Information section). The transceiver presents 14 unit loading to the RS-485 bus allowing up to 128 nodes to be connected together without the use of repeaters. The transceiver draws 200 A of supply current when unloaded or fully loaded with the driver disabled and operates from a single +5V supply. The driver is short-circuit current limited and is protected against excessive power dissipation by thermal shutdown circuitry that places the driver outputs into TRI-STATE (R) (High Impedance state) under fault conditions. The driver guarantees a minimum of 1.5V differential output voltage with maximum loading across the common mode range (VOD3). The receiver has a failsafe feature that guarantees a logic-high output if the input is open circuit. The DS1487 is available in surface mount and DIP packages. n n n n n n n Connection and Logic Diagram Truth Table n n n n Meets TIA/EIA RS-485 multipoint standard Allows up to 128 transceivers on the bus (14 U.L.) Guaranteed full load output voltage (VOD3) Low quiescent current: 200 A typ -7V to +12V common-mode input voltage range TRI-STATE outputs on driver and receiver AC performance: -- Driver transition time: 25 ns typ -- Driver propagation delay: 40 ns typ -- Driver skew: 1 ns typ -- Receiver propagation delay: 200 ns typ -- Receiver skew: 20 ns typ Half-duplex flow through pinout Operates from a single 5V supply Current-limiting and thermal shutdown for driver overload protection Pin and functional compatible with MAX1487 DRIVER SECTION DIP and SOIC RE (Note 1) DE DI A B X H H H L X H L L H X L X Z Z RECEIVER SECTION DS012920-1 *Note: Non Terminated, Open Input only Order Number Temp. Range Package/### DS1487N 0C to +70C DIP/N08E DS1487M 0C to +70C SOP/M08A RE (Note 1) DE A-B RO L L +0.2V H L L -0.2V L H X X Z L L OPEN (Note 1) H X = indeterminate Z = TRI-STATE Note 1: Non Terminated, Open Input only TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2000 National Semiconductor Corporation DS012920 www.national.com DS1487 Low Power RS-485 14 Unit Load Multipoint Transceiver July 1998 DS1487 Absolute Maximum Ratings (Note 2) M Package N Package Storage Temperature Range Lead Temperature Range (Soldering, 4 sec.) ESD (HBM) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage (VCC) +12V Enable Input Voltage (RE (Note 1), DE) -0.5V to (VCC + 0.5V) Driver Input Voltage (DI) -0.5V to (VCC + 0.5V) Driver Output Voltage (A, B) -14V to +14V Receiver Input Voltage (A, B) -14V to +14V Receiver Output Voltage (RO) -0.5V to (VCC + 0.5V) Maximum Package Power Dissipation @ +25C M Package 1.19W N Package 0.74W Derate M Package 9.5 mW/C above +25C Derate N Package 6.0 mW/C above +25C Maximum Package Power Dissipation @ +70C 0.76W 0.47W -65C to +150C +260C 2 kV Recommended Operating Conditions Supply Voltage (VCC) Operating Free Air Temperature (TA) DS1487 Bus Common Mode Voltage Min +4.75 Typ +5.0 0 -7 +25 Max Units +5.25 V +70 +12 C V Electrical Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified (Notes 3, 4) Symbol Parameter Conditions Pin Min Typ Max Units A, B 1.5 5 VOD1 Differential Driver Output Voltage (No Load) VOD2 Differential Driver Output Voltage RL = 50, (RS422), Figure 1 2 2.8 with Load RL = 27, (RS485), Figure 1 1.5 2.3 Change in Magnitude of Output RL = 27 or 50 (Note 5) VOD V V 5 V 0.2 |V| 5 V 3 V 0.2 |V| Differential Voltage VOD3 Differential Driver Output Voltage -- R1 = 54, R2 = 375 Full Load with Max VCM VTEST = -7V to +12V, Figure 2 VOC Driver Common-Mode Output Voltage RL = 27 or 50, Figure 1 VOC Change in Magnitude of Common-Mode Output Voltage RL = 27 or 50, Figure 1 (Note 5) 1.5 2.0 0 VIH Input High Voltage DI, DE, VIL Input Low Voltage RE (Note 1) IIN1 Input Current IIN2 Input Current (Note 6) VIN = +12V DE = 0V, VCC = 0V or 5.25V VIN = -7V VTH Receiver Differential Threshold Voltage -7V VCM +12V VTH Receiver Input Hysteresis VCM = 0V VOH Receiver Output High Voltage IO = -4 mA, VID = 0.2V VOL Receiver Output Low Voltage IO = 4 mA, VID = -0.2V 0.5 V IOZR TRI-STATE Output Current at Receiver 0.4V VO 2.4V 1 A 2.0 V 2 A 250 A 0 -100 -200 A VIN = 0V or VCC A, B 0 190 -0.2 0.2 70 RO RIN Receiver Input Resistance -7V VIN +12V A, B ICC No-Load Supply Current (Note 7) DE = VCC, RE (Note 1) = 0V or VCC VCC IOSD1 Driver Short Circuit Current, VO = HIGH -7V VO +12V IOSD2 Driver Short Circuit Current, VO = LOW -7V VO +12V IOSR Receiver Short Circuit Current VO = GND 48 68 200 RO 2 V 200 A, B 7 V mV 3.5 DE = 0V, RE (Note 1) = 0V or VCC www.national.com V 0.8 k 500 A 500 A 250 mA -250 mA 85 mA DS1487 Switching Characteristics Over Supply Voltage and Operating Temperature Ranges, unless otherwise specified (Notes 4, 8, 9) Symbol Parameter Conditions Min Typ Max Units RL = 54, CL = 100 pF 10 40 80 ns 10 39 80 ns tPLHD Driver Differential Propagation Delay -- Low to High tPHLD Driver Differential Propagation Delay -- High to Low tSKEW Differential Skew |tPHLD - tPLHD| 0 1 10 ns tr Driver Rise Time 3 25 50 ns tf Driver Fall Time 3 25 50 ns tZH Driver Enable to Output High CL = 100 pF 50 200 ns tZL Driver Enable to Output Low CL = 100 pF 65 200 ns tLZ Driver Disable from Output Low CL = 15 pF 80 200 ns tHZ Driver Disable from Output High CL = 15 pF 80 200 ns tPLHD Receiver Differential Propagation Delay -- Low to High CL = 15 pF (RO) 30 190 400 ns tPHLD Receiver Differential Propagation Delay -- High to Low 30 210 400 ns tSKEW Differential Skew |tPHLD - tPLHD| 0 20 50 ns tZH Receiver Enable to Output High 45 150 ns CL = 15 pF tZL Receiver Enable to Output Low 40 150 ns tLZ Receiver Disable from Output Low 50 150 ns tHZ Receiver Disable from Output High 55 150 ns fmax Maximum Data Rate (Note 10) 2.0 Mbps Note 2: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" specifies conditions of device operation. Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. All voltages are referenced to ground except VOD1/2/3and VID. Note 4: All typicals are given for: VCC = +5.0V, TA = +25C. Note 5: |VOD| and |VOC| are changes in magnitude of VOD and VOC respectively, that occur when the input changes state. Note 6: IIN2 includes the receiver input current and driver TRI-STATE leakage current. Note 7: Supply current specification is valid for loaded transmitters when DE = 0V or enabled (DE = H) with no load. Note 8: f = 1 MHz, tr and tf 6 ns, ZO = 50. Note 9: CL includes jig and probe capacitance. Note 10: fmax is the guaranteed data rate for 50 ft of twisted pair cable. fmax may be conservatively determined from the ratio of driver transition time (tr) to the data rate unit interval (1/fmax). Using a 10% ratio yields fmax = (0.1)/50 ns = 2.0 Mb/s. Higher data rates may be supported by allowing larger ratios. Parameter Measurement Information DS012920-2 FIGURE 1. VOD DS012920-4 FIGURE 3. DS012920-3 FIGURE 2. VOD3 3 www.national.com DS1487 Parameter Measurement Information (Continued) DS012920-8 FIGURE 7. DS012920-5 DS012920-9 FIGURE 4. FIGURE 8. DS012920-10 *Note: Non Terminated, Open Input only FIGURE 9. DS012920-6 FIGURE 5. DS012920-7 DS012920-11 FIGURE 6. FIGURE 10. DS012920-12 *Note: Non Terminated, Open Input only FIGURE 11. www.national.com 4 DS1487 Parameter Measurement Information (Continued) DS012920-13 *Note: Non Terminated, Open Input only FIGURE 12. DS012920-14 *Note: Non Terminated, Open Input only FIGURE 13. Pin Descriptions Pin # I/O Name Function 1 O RO 2 I RE (Note 1) 3 I DE Driver Output Enable: The driver outputs (A and B) are enabled when DE is high; they are in TRI-STATE when DE is low. Pins A and B also function as the receiver input pins (see below). 4 I DI Driver Input: A low on DI forces A low and B high while a high on DI forces A high and B low when the driver is enabled. 5 NA GND 6 I/O A Non-inverting Driver Output and Receiver Input pin. Driver output levels conform to RS-485 signaling levels. 7 I/O B Inverting Driver Output and Receiver Input pin. Driver output levels conform to RS-485 signaling levels. 8 NA VCC Receiver Output: If A > B by 200 mV, RO will be high; If A < B by 200 mV, RO will be low. RO will be high also if the inputs (A and B) are open (non-terminated). Receiver Output Enable: RO is enabled when RE (Note 1) is low; RO is in TRI-STATE when RE (Note 1) is high. Ground Power Supply: 4.75V VCC 5.25V Applications Information The DS1487 is a low power transceiver designed for use in RS-485 multipoint applications. The DS1487 can transmit data up to 2.0 Mbps based on a ratio of driver transition time to the unit interval (bit time) of 10%. This maximum data rate may be further limited by the interconnecting media. The DS1487 provides a 14 unit load to the RS-485 bus across the common mode range of -7V to +12V. This allows up to 128 transceivers (14 unit load) to be connected to the bus. The DS1487 also guarantees the driver's output differential voltage into a worst case load that models standard termination loads and 32 unit loads (=128 DS1487's) referenced to the maximum common mode voltage extremes. With a minimum of 1.5V swing into this load, a 1.3V differential noise margin is supported along with the standard common mode rejection range of the receivers. 5 www.national.com DS1487 Applications Information A typical multipoint application is shown in the following figure. Note that termination is typically required but is only located at the two ends of the cable (not on every node). Commonly pull up and pull down resistors may be required at one end of the bus to provide a failsafe bias. These resistors provide a bias to the line when all drivers are in TRI-STATE. See National Application Note 847 for a complete discussion of failsafe biasing of differention buses. (Continued) Due to the multipoint nature of the bus, contention between drivers may occur. This will not cause damage to the drivers since they feature short-circuit protection and also thermal shutdown protection. Thermal shutdown senses die temperature and puts the driver outputs into TRI-STATE if a fault condition occurs that causes excessive power dissipation which can elevate the junction temperature to +150C. DS012920-16 www.national.com 6 DS1487 Physical Dimensions inches (millimeters) unless otherwise noted Order Number DS1487N NS Package Number N08E 7 www.national.com DS1487 Low Power RS-485 14 Unit Load Multipoint Transceiver Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 87 90 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Email: nsj.crc@jksmtp.nsc.com Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated