1
Rectifier Device Data
Surface Mount Power Package
...Employs the Schottky Barrier principle in a large area metal–to–silicon
power diode. State–of–the–art geometry features epitaxial construction with
oxide passivation and metal overlay contact. Ideally suited for low voltage,
high frequency rectification, or as free wheeling and polarity protection diodes,
in surface mount applications where compact size and weight are critical to
the system.
•Very Low Forward Voltage Drop (0.395 Volts Max @ 1.0 A, TJ = 25°C)
•Small Compact Surface Mountable Package with J–Bend Leads
•Highly Stable Oxide Passivated Junction
•Guardring for Stress Protection
Mechanical Characteristics
•Case: Epoxy, Molded
•Weight: 95 mg (approximately)
•Finish: All External Surfaces Corrosion Resistant and Terminal Leads are
Readily Solderable
•Lead and Mounting Surface Temperature for Soldering Purposes: 260°C
Max. for 10 Seconds
•Shipped in 12 mm Tape and Reel, 2500 units per reel
•Polarity: Notch in Plastic Body Indicates Cathode Lead
•Marking: B130
MAXIMUM RATINGS
Rating Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
30 Volts
Average Rectified Forward Current TL = 120°C
TL = 110°CIF(AV) 1.0
2.0 Amps
Nonrepetitive Peak Surge Current
(Surge applied at rated load conditions halfwave, single phase, 60 Hz) IFSM 40 Amps
Operating Junction Temperature TJ– 65 to +125 °C
THERMAL CHARACTERISTICS
Thermal Resistance — Junction to Lead
(TL = 25°C) RθJL 12 °C/W
ELECTRICAL CHARACTERISTICS
Maximum Instantaneous Forward Voltage (1)
(iF = 1.0 A, TJ = 25°C)
(iF = 2.0 A, TJ = 25°C)
VF0.395
0.445
Volts
Maximum Instantaneous Reverse Current (1)
(Rated dc Voltage, TJ = 25°C)
(Rated dc Voltage, TJ = 100°C)
IR1.0
10
mA
(1) Pulse Test: Pulse Width = 300 µs, Duty Cycle ≤2%.
Designer’s Data for “W orst Case” Conditions — The Designer’s Data Sheet permits the design of most circuits entirely from the information presented. SOA Limit
curves — representing boundaries on device characteristics — are given to facilitate “worst case” design.
Preferred devices are Motorola recommended choices for future use and best overall value.
Motorola, Inc. 1996
SCHOTTKY BARRIER
RECTIFIER
1.0 AMPERE
30 VOLTS
CASE 403A–03
Motorola Preferred Device
Order this document
by MBRS130LT3/D
SEMICONDUCTOR TECHNICAL DATA
Rev 1
MBRS130LT3
2Rectifier Device Data
iF, INSTANTANEOUS FORWARD CURRENT (AMPS)
10
5.0
2.0
1.0
0.5
0.2
0.1 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
vF, INSTANTANEOUS VOLTAGE (VOLTS)
Figure 1. Typical Forward Voltage
TJ = 100
°
C
25
°
C
IR, REVERSE LEAKAGE CURRENT (mA)
100
10
1.0
0.1
0.01
0.001 0 3 6 9 12 15 18 21 24 27 30
VR, REVERSE VOLTAGE (VOLTS)
Figure 2. Typical Reverse Leakage Current
TJ = 100
°
C
25
°
C
IF(AV), A VERAGE FORWARD CURRENT (AMPS)
8
7
6
5
4
3
2
1
050 60 70 80 90 100 110 120 130
TC, CASE TEMPERATURE (
°
C)
Figure 3. Current Derating (Case)
SQUARE
WAVE
DC
TJ = 100
°
C
PF(AV), AVERAGE POWER DISSIPA TION (WATTS)
8
7
6
5
4
3
2
1
001 2345 67 8
I
F(AV), A VERAGE FORWARD CURRENT (AMPS)
Figure 4. Typical Power Dissipation
20 10 5
π
DC
IPK
IAV =
SQUARE
WAVE
C, CAPACITANCE (pF)
400
350
300
250
200
150
100
50
00 4 8 121620242832
V
R
, REVERSE VOLT AGE (VOLTS)
Figure 5. Typical Capacitance
RATED VOLTAGE APPLIED
R
θ
JC = 12
°
C/W
TJ = 100
°
C
NOTE: TYPICAL CAPACITANCE
AT 0 V = 290 pF
MBRS130LT3
3
Rectifier Device Data
PACKAGE DIMENSIONS
A
S
DB
J
P
K
C
H
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. D DIMENSION SHALL BE MEASURED WITHIN
DIMENSION P.
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A0.160 0.180 4.06 4.57
B0.130 0.150 3.30 3.81
C0.075 0.095 1.90 2.41
D0.077 0.083 1.96 2.11
H0.0020 0.0060 0.051 0.152
J0.006 0.012 0.15 0.30
K0.030 0.050 0.76 1.27
P0.020 REF 0.51 REF
S0.205 0.220 5.21 5.59
CASE 403A–03
ISSUE B
MBRS130LT3
4Rectifier Device Data
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding
the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola
data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury
or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that
Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal
Opportunity/Af firmative Action Employer.
Mfax is a trademark of Motorola, Inc.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center,
P.O. Box 5405, Denver, Colorado 80217. 303–675–2140 or 1–800–441–2447 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 81–3–3521–8315
Mfax: RMF AX0@email.sps.mot.com – TOUCHT ONE 602–244–6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,
INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298
MBRS130LT3/D
◊CODELINE TO BE PLACED HERE
