Thyristors Surface Mount - 120V - 240V > MKP3V120, MKP3V240 MKP3V120, MKP3V240 Pb Description Bidirectional devices designed for direct interface with the ac power line. Upon reaching the breakover voltage in each direction, the device switches from a blocking state to a low voltage on-state. Conduction will continue like a Triac until the main terminal current drops below the holding current. The plastic axial lead package provides high pulse current capability at low cost. Glass passivation insures reliable operation. Features * High Pressure Sodium Vapor Lighting * Strobes and Flashers * Ignitors * High Voltage Regulators * Pulse Generators Axial Lead * Used to Trigger Gates of SCR's and Triac AXIAL LEAD CASE 59 STYLE 2 * Indicates UL Registered - File #E128662 * These are Pb-Free Devices Functional Diagram Additional Information Datasheet Resources Samples (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount - 120V - 240V > MKP3V120, MKP3V240 Maximum Ratings (TJ = 25C unless otherwise noted) Rating Symbol Peak Repetitive Off-State Voltage (Note 1) Value VDRM, (- 40 to 125C, Sine Wave, 50 to 60 Hz, Gate Open) VRRM MKP3V120 V 180 MKP3V240 On-State RMS Current (All Conduction Angles; TL = 80C, 90 Unit 1.0 A ITSM 20 A Operating Junction Temperature Range TJ -40 to +125 C Storage Temperature Range Tstg -40 to +150 C Lead Length = 3/8") IT Peak Non-Repetitive Surge Current (60 Hz One Cycle, Sine Wave, TJ = 125C) (RMS) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Thermal Characteristics Rating Thermal Resistance, Junction-to-Lead (Lead Length = 3/8") Lead Solder Temperature (Lead Length 1/16" from Case, 10 s Max) Symbol Value R8JL 15 TL 260 Unit C/W C (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount - 120V - 240V > MKP3V120, MKP3V240 Electrical Characteristics - OFF (TJ = 25C unless otherwise noted; Electricals apply in both directions) Characteristic Repetitive Peak Off-State Current Symbol Min Typ Max Unit IDRM - - 10 A (50 to 60 Hz Sine Wave) VDRM = 90V, MKP3V120 VDRM = 180V, MKP3V240 Electrical Characteristics - ON (TJ = 25C unless otherwise noted; Electricals apply in both directions) Characteristic Symbol MKP3V120 IBO =200 A Breakover Voltage MKP3V240 IBO =200 A Min Typ Max 110 _ 130 Unit VBO V 220 _ 250 VTM - 1.1 1.5 V Dynamic Holding Current (Sine Wave, 60 Hz, RL = 100 ) IH _ _ 100 mA Switching Resistance (Sine Wave, 50 to 60 Hz) RS 0.1 _ _ k Peak On-State Voltage (ITM = 1 A Peak, Pulse Width 300 s, Duty Cycle 2%) Dynamic Characteristics Characteristic Symbol Min Typ Max Unit Critical Rate-of-Rise of On-State Current, Critical Damped Waveform Circuit (IPK = 130 , Pulse Width = 10 sec) dv/dt _ 120 - V/s (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount - 120V - 240V > MKP3V120, MKP3V240 Voltage Current Characteristic of SCR Symbol VDRM Parameter Peak Repetitive Forward Off State Voltage IDRM Peak Forward Blocking Current VRRM Peak Repetitive Reverse Off State Voltage IRRM Peak Reverse Blocking Current VTM Maximum On State Voltage I S I IS I S) S IH S I (I S ) Holding Current Figure 1. Maximum Case Temperature Figure 2. Maximum Ambient Temperature Figure 3. Typical Forward Voltage Figure 4. Typical Power Dissipation (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount - 120V - 240V > MKP3V120, MKP3V240 Thermal Characterstics Figure 5. Thermal Response Typical Characterstics Figure 6. Typical Breakover Current Figure 7. Typical Holding Current (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17 Thyristors Surface Mount - 120V - 240V > MKP3V120, MKP3V240 Part Marking System Dimensions K D AXIAL LEAD (No Polarity) CASE 267 STYLE 2 A 1 2 B A MKP 3Vxx0 YYWW K Dim A Inches A= Assembly Location xx = 12 or 24 YY, Y= Year WW = Work Week Millimeters Min Max Min Max 0.287 0.374 7.30 9.50 B 0.189 0.209 4.80 5.30 D 0.047 0.051 1.20 1.30 K 1.000 --- 25.40 --- (Note: Microdot may be in either location) Ordering Information Device 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. Package Shipping Axial Lead 500 Units / Box 1500 / Tape & Reel 500 Units / Box 1500 / Tape & Reel MKP3V120G 2. CONTROLLING DIMENSION: INCH. 3. ALL RULES AND NOTES ASSOCIATED WITH JEDEC DO-41 267-04 OBSOLETE, NEW STANDARD 267-05. STYLE 2: NO POLARITY MKP3V120RLG MKP3V240G MKP3V240RLG Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at: www.littelfuse.com/disclaimer-electronics (c) 2017 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 08/30/17