2008-2011 Microchip Technology Inc. DS41364E
PIC16(L)F1934/6/7
Data Sheet
28/40/44-Pin Flash-Based, 8-Bit
CMOS Microcontrollers with
LCD Driver and nanoWatt XLP Technology
DS41364E-page 2 2008-2011 Microchip Technology Inc.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, dsPIC,
KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART,
PIC32 logo, rfPIC and UNI/O are registered trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor,
MXDEV, MXLAB, SEEVAL and The Embedded Control
Solutions Company are registered trademarks of Microchip
Technology Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial
Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified
logo, MPLIB, MPLINK, mTouch, Omniscient Code
Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit,
PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance,
TSHARC, UniWinDriver, WiperLock and ZENA are
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008-2011, Microchip Technology Incorporated, Printed in
the U.S.A., All Rights Reserved.
Printed on recycled paper.
ISBN: 978-1-61341-013-4
Note the following details of the code protection feature on Microch ip devices:
Microchip products meet the specification contained in their particular Microchip Data Sheet.
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
Microchip is willing to work with the customer who is concerned about the integrity of their code.
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperiph erals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
2008-2011 Microchip Technology Inc. DS41364E-page 3
PIC16(L)F1934/6/7
Devices Included In This Data Sheet:
Other PIC16(L)F193X Devices Available:
High-Performance RISC CPU:
Only 49 Instructions to Learn:
- All single-cycle instructions except branches
Operating Speed:
- DC – 32 MHz oscillator/clock input
- DC – 125 ns instruction cycle
Up to 16K x 14 Words of Flash Program Memory
Up to 1024 Bytes of Data Memory (RAM)
Interrupt Capability with Automatic Context
Saving
16-Level Deep Hardware Stack
Direct, Indirect and Relative Addressing modes
Processor Read Access to Program Memory
Pinout Compatible to other 28/40/44-pin
PIC16CXXX and PIC16FXXX Microcontrollers
S pecial Microcontroller Features:
Precision Internal Oscillator:
- Factory calibrated to ±1%, typical
- Software selectable frequency range from
32 MHz to 31 kHz
Power-Saving Sleep mode
Power-on Reset (POR)
Power-up Timer (PWRT) and Oscillator Start-up
Timer (OST)
Brown-out Reset (BOR)
- Selectable between two trip points
- Disable in Sleep option
Multiplexed Master Clear with Pull-up/Input Pin
Programmable Code Protection
High Endurance Flash/EEPROM cell:
- 100,000 write Flash endurance
- 1,000,000 write EEPROM endurance
- Flash/Data EEPROM retention: > 40 years
Wide Operating Voltage Range:
- 1.8V-5.5V (PIC16F193X)
- 1.8V-3.6V (PIC16LF193X)
PIC16LF193X Low-Power Features:
Standby Current:
- 60 nA @ 1.8V, typical
Operating Current:
-7.0A @ 32 kHz, 1.8V, typical (PIC16LF193X)
-150A @ 1 MHz, 1.8V, typical (PIC16LF193X)
Timer1 Oscillator Current:
- 600 nA @ 32 kHz, 1.8V, typical
Low-Power Watchdog Timer Current:
- 500 nA @ 1.8V, typical (PIC16LF193X)
Peripheral Feat ures:
Up to 35 I/O Pins and 1 Input-only Pin:
- High-current source/sink for direct LED drive
- Individually programmable interrupt-on-pin
change pins
- Individually programmable weak pull-ups
Integrated LCD Controller:
- Up to 96 segments
- Variable clock input
- Contrast control
- Internal voltage reference selections
Capacitive Sensing module (mTouchTM)
- Up to 16 selectable channels
A/D Converter:
- 10-bit resolution and up to 14 channels
- Selectable 1.024/2.048/4.096V voltage
reference
Timer0: 8-Bit Timer/Counter with 8-Bit
Programmable Prescaler
Enhanced Timer1
- Dedicated low-power 32 kHz oscillator driver
- 16-bit timer/counter with prescaler
- External Gate Input mode with toggle and
single shot modes
- Interrupt-on-gate completion
Timer2, 4, 6: 8-Bit Timer/Counter with 8-Bit Period
Register, Prescaler and Postscaler
Two Capture, Compare, PWM modules (CCP)
- 16-bit Capture, max. resolution 125 ns
- 16-bit Compare, max. resolution 125 ns
- 10-bit PWM, max. frequency 31.25 kHz
Three Enhanced Capture, Compare, PWM
modules (ECCP)
- 3 PWM time-base options
- Auto-shutdown and auto-restart
- PWM steering
- Programmable dead-band delay
PIC16F1934 PIC16LF1934
PIC16F1936 PIC16LF1936
PIC16F1937 PIC16LF1937
PIC16(L)F1933 (DS41575)
PIC16(L)F1938/9 (DS41574)
Note: PIC16(L)F193X devices referred to in this
data sheet apply to PIC16(L)F1934/6/7.
28/40/44-Pin F l ash-Based, 8-Bi t CMOS Microcon trollers wit h
LCD Driver with nanoWatt XLP Technology
PIC16(L)F1934/6/7
DS41364E-page 4 2008-2011 Microchip Technology Inc.
Peripheral Feat ures (Continued):
Master Synchronous Serial Port (MSSP) with SPI
and I2 CTM with:
- 7-bit address masking
- SMBus/PMBusTM compatibility
- Auto-wake-up on start
Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART)
- RS-232, RS-485 and LIN compatible
- Auto-Baud Detect
SR Latch (555 Timer):
- Multiple Set/Reset input options
- Emulates 555 Timer applications
2 Comparators:
- Rail-to-rail inputs/outputs
- Power mode control
- Software enable hysteresis
Voltage Reference module:
- Fixed Voltage Reference (FVR) with 1.024V,
2.048V and 4.096V output levels
- 5-bit rail-to-rail resistive DAC with positive
and negative reference selection
PIC16(L)F193X Famil y Types
Device
Program Memory
Flash (words)
Data EEPROM
(bytes)
SRAM (bytes)
I/O’s
10-bit A/D
(ch)
CapSense
(ch)
Comparators
Timers
8/16-bit
EUSART
I2C™/SPI
ECCP
CCP
LCD
PIC16F1934
PIC16LF1934 4096 256 256 36 14 16 2 4/1 Yes Yes 3 2 24/4
PIC16F1936
PIC16LF1936 8192 256 512 25 11 8 2 4/1 Yes Yes 3 2 16(1)/4
PIC16F1937
PIC16LF1937 8192 256 512 36 14 16 2 4/1 Yes Yes 3 2 24/4
Note 1: COM3 and SEG15 share the same physical pin on PIC16(L)F1936, therefore, SEG15 is not available when using 1/4
multiplex displays.
2008-2011 Microchip Technology Inc. DS41364E-page 5
PIC16(L)F1934/6/7
Pin Diagram – 28-Pin SPDIP/SOIC/SSOP (PIC16(L)F1936)
28-pin SPDIP, SOIC, SSOP
PIC16F1936
PIC16LF1936
1
2
3
4
5
6
7
8
9
10
VPP/MCLR/RE3
SEG12/VCAP(2)/SS(1)/SRNQ(1)/C2OUT(1)/C12IN0-/AN0/RA0
SEG7/C12IN1-/AN1/RA1
COM2/DACOUT/VREF-/C2IN+/AN2/RA2
SEG15/COM3/VREF+/C1IN+/AN3/RA3
SEG4/CCP5/SRQ/T0CKI/CPS6/C1OUT/RA4
SEG5/VCAP(2)/SS(1)/SRNQ(1)/CPS7/C2OUT(1)/AN4/RA5
RB6/ICSPCLK/ICDCLK/SEG14
RB5/AN13/CPS5/P2B(1)/CCP3(1)/P3A(1)/T1G(1)/COM1
RB4/AN11/CPS4/P1D/COM0
RB3/AN9/C12IN2-/CPS3/CCP2(1)/P2A(1)/VLCD3
RB2/AN8/CPS2/P1B/VLCD2
RB1/AN10/C12IN3-/CPS1/P1C/VLCD1
RB0/AN12/CPS0/CCP4/SRI/INT/SEG0
VDD
VSS
11
12
13
14 15
16
17
18
19
20
28
27
26
25
24
23
22
21
VSS
SEG2/CLKIN/OSC1/RA7
SEG1/VCAP(2)/CLKOUT/OSC2/RA6
P2B(1)/T1CKI/T1OSO/RC0
P2A(1)/CCP2(1)/T1OSI/RC1
SEG3/P1A/CCP1/RC2
SEG6/SCL/SCK/RC3
RC5/SDO/SEG10
RC4/SDI/SDA/T1G(1)/SEG11
RC7/RX/DT/P3B/SEG8
RC6/TX/CK/CCP3(1)/P3A(1)/SEG9
RB7/ICSPDAT/ICDDAT/SEG13
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1936 devices only.
PIC16(L)F1934/6/7
DS41364E-page 6 2008-2011 Microchip Technology Inc.
Pin Diagram – 28-Pin QFN/UQFN (PIC16(L)F1936)
2
3
6
1
18
19
20
21
15
7
16
17
P2B(1)/T1CKI/T1OSO/RC0
5
4
RB7/ICSPDAT/ICDDAT/SEG13
RB6/ICSPCLK/ICDCLK/SEG14
RB5/AN13/CPS5/P2B(1)/CCP3(1)/P3A(1)/T1G(1)/COM1
RB4/AN11/CPS4/P1D/COM0
RB3/AN9/C12IN2-/CPS3/CCP2(1)/P2A(1)/VLCD3
RB2/AN8/CPS2/P1B/VLCD2
RB1/AN10/C12IN3-/CPS1/P1C/VLCD1
RB0/AN12/CPS0/CCP4/SRI/INT/SEG0
VDD
VSS
RC7/RX/DT/P3B/SEG8
SEG9/P3A(1)/CCP3(1)/CK/TX/RC6
SEG10/SDO/RC5
SEG11/T1G(1)/SDA/SDI/RC4
RE3/MCLR/VPP
RA0/AN0/C12IN0-/C2OUT(1)/SRNQ(1)/SS(1)/VCAP(2)/SEG12
RA1/AN1/C12IN1-/SEG7
COM2/DACOUT/VREF-/C2IN+/AN2/RA2
SEG15/COM3/VREF+/C1IN+/AN3/RA3
SEG4/CCP5/SRQ/T0CKI/CPS6/C1OUT/RA4
SEG5(1)/VCAP(2)/SS(1)/SRNQ/CPS7/C2OUT(1)/AN4/RA5
VSS
SEG2/CLKIN/OSC1/RA7
SEG1/VCAP(2)/CLKOUT/OSC2/RA6
(1)P2A/(1)CCP2/T1OSI/RC1
SEG3/P1A/CCP1/RC2
SEG6/SCL/SCK/RC3
9
10
13
8
14
12
11
27
26
23
28
22
24
25
PIC16(L)F1936
PIC16LF1936
28-pin QFN/UQF N
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1936 devices only.
2008-2011 Microchip Technology Inc. DS41364E-page 7
PIC16(L)F1934/6/7
TABLE 1: 28-PIN SUMMARY (PIC16(L)F1936)
I/O
28-Pin SP DIP
28-Pin QFN/UQFN
ANSEL
A/D
Cap Sense
Comparator
SR Latch
Timers
CCP
EUSART
MSSP
LCD
Interrupt
Pull-up
Basic
RA0 227 YAN0 C12IN0-/
C2OUT(1) SRNQ(1) SS(1) SEG12 VCAP(2)
RA1 3 28 Y AN1 C12IN1- SEG7
RA2 4 1 Y AN2/
VREF-
C2IN+/
DACOUT
COM2
RA3 5 2 Y AN3/
VREF+
C1IN+ SEG15/
COM3
——
RA4 6 3 Y CPS6 C1OUT SRQ T0CKI CCP5 SEG4
RA5 7 4 Y AN4 CPS7 C2OUT(1) SRNQ(1) ——SS
(1) SEG5 VCAP(2)
RA6 10 7 SEG1 OSC2/
CLKOUT
VCAP(2)
RA7 9 6 SEG2 OSC1/
CLKIN
RB0 21 18 YAN12 CPS0 SRI CCP4 SEG0 INT/
IOC
Y
RB1 22 19 Y AN10 CPS1 C12IN3- P1C VLCD1 IOC Y
RB2 23 20 YAN8 CPS2 P1B VLCD2 IOC Y
RB3 24 21 Y AN9 CPS3 C12IN2- CCP2(1)/
P2A(1) VLCD3 IOC Y
RB4 25 22 YAN11 CPS4 P1D COM0 IOC Y
RB5 26 23 Y AN13 CPS5 T1G(1) P2B(1)
CCP3(1)/
P3A(1)
——COM1IOCY
RB6 27 24 SEG14 IOC YICSPCLK/
ICDCLK
RB7 28 25 SEG13 IOC Y ICSPDAT/
ICDDAT
RC0 11 8 T1OSO/
T1CKI
P2B(1)
RC1 12 9 T1OSI CCP2(1)/
P2A(1) ——
RC2 13 10 CCP1/
P1A
SEG3
RC3 14 11 SCK/SCL SEG6
RC4 15 12 T1G(1) SDI/SDA SEG11
RC51613—— —— SDOSEG10
RC6 17 14 CCP3(1)
P3A(1) TX/CK SEG9
RC7 18 15 P3B RX/DT SEG8
RE3126—— —— YMCLR
/VPP
VDD 20 17 VDD
Vss 8,
19
5,
16
—— —— VSS
Note 1: Pin functions can be moved using the APFCON register.
2: PIC16F1936 devices only.
PIC16(L)F1934/6/7
DS41364E-page 8 2008-2011 Microchip Technology Inc.
Pin Diagram – 40-Pin PDIP (PIC16(L)F1934/7)
40-Pin PDIP
PIC16F1934/7
PIC16LF1934/7
2
3
4
5
6
7
8
9
10
VPP/MCLR/RE3
SEG12/VCAP(2)/SS(1)/SRNQ(1)/C2OUT(1)/C12IN0-/AN0/RA0
SEG7/C12IN1-/AN1/RA1
COM2/DACOUT/VREF-/C2IN+/AN2/RA2
SEG15/VREF+/C1IN+/AN3/RA3
SEG4/SRQ/T0CKI/CPS6/C1OUT/RA4
SEG5/VCAP(2)/SS(1)/SRNQ(1)/CPS7/C2OUT(1)/AN4/RA5
SEG21/CCP3(1)/P3A(1)/AN5/RE0
SEG22/P3B/AN6/RE1
SEG23/CCP5/AN7/RE2
RB6/ICSPCLK/ICDCLK/SEG14
RB5/AN13/CPS5/CCP3(1)/P3A(1)/T1G(1)/COM1
RB4/AN11/CPS4/COM0
RB3/AN9/C12IN2-/CPS3/CCP2(1)/P2A(1)/VLCD3
RB2/AN8/CPS2/VLCD2
RB1/AN10/C12IN3-/CPS1/VLCD1
RB0/AN12/CPS0/SRI/INT/SEG0
VDD
VSS
RD2/CPS10/P2B(1)
11
12
13
14
15
16
17
18
19
20
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
VDD
VSS
SEG2/CLKIN/OSC1/RA7
SEG1/VCAP(2)/CLKOUT/OSC2/RA6
P2B(1)/T1CKI/T1OSO/RC0
P2A(1)/CCP2(1)/T1OSI/RC1
SEG3/P1A/CCP1/RC2
SEG6/SCK/SCL/RC3
COM3/CPS8/RD0
CCP4/CPS9/RD1
RC5/SDO/SEG10
RC4/SDI/SDA/T1G(1)/SEG11
RD3/CPS11/P2C/SEG16
RD4/CPS12/P2D/SEG17
RC7/RX/DT/SEG8
RC6/TX/CK/SEG9
RD7/CPS15/P1D/SEG20
RD6/CPS14/P1C/SEG19
RD5/CPS13/P1B/SEG18
RB7/ICSPDAT/ICDDAT/SEG13
1
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/7 devices only.
2008-2011 Microchip Technology Inc. DS41364E-page 9
PIC16(L)F1934/6/7
Pin Diagram 40-Pin UQFN 5X5 (PIC16(L)F1934/7)
40-pin UQFN
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/7 devices only.
10
2
3
4
5
6
1
17
18
19
20
11
12
13
14
35
8
7
40
39
38
37
36
15
16
27
28
29
30
21
22
23
24
25
26
33
31
32
9
34
PIC16F1934/7
PIC16LF1934/7
SEG15/C1IN+/VREF+/AN3/RA3
COM2/DACOUT/C2IN+/VREF-/AN2/RA2
SEG7/C12IN1-/AN1/RA1
SEG12/SRNQ(1)/C2OUT(1)/C12IN0-/VCAP(2)/SS(1)/AN0/RA0
VPP/MCLR/RE3
SEG13/ICDDAT/ICSPDAT/RB7
SEG14/ICDCLK/ICSPCLK/RB6
COM1/T1G(1)/CCP3(1)/P3A(1)/CPS5/AN13/RB5
COM0/CPS4/AN11/RB4
VSS
VDD
SEG0/SRI/INT/CPS0/AN12/RB0
VLCD1/C12IN3-/CPS1/AN10/RB1
VLCD2/CPS2/AN8/RB2
VLCD3/P2A(1)/CCP2(1)/C12IN2-/CPS3/AN9/RB3
SEG8/DT/RX/RC7
SEG17/P2D/CPS12/RD4
SEG18/P1B/CPS13/RD5
SEG19/P1C/CPS14/RD6
SEG20/P1D/CPS15/RD7
RC6/TX/CK/SEG9
RC5/SDO/SEG10
RC4/SDI/SDA/T1G(1)/SEG11
RD3/CPS11/P2C/SEG16
RD2/CPS10/P2B(1)
RD1/CPS9/CCP4
RD0/CPS8/COM3
RC3/SCK/SCL/SEG6
RC2/CCP1/P1A/SEG3
RC1/T1OSI/CCP2(1)/P2A(1)
RC0/T1OSO/T1CKI/P2B
RA6/OSC2/CLKOUT/VCAP(2)/SEG1
RA7/OSC1/CLKIN/SEG2
VSS
VDD
RE2/AN7/CCP5/SEG23
RE1/AN6/P3B/SEG22
RE0/AN5/CCP3(1)/P3A(1)/SEG21
RA4/CPS6/T0CKI/C1OUT/SRQ/SEG4
RA5/AN4/CPS7/SS(1)/VCAP(2)/SRNQ(1)/C2OUT(1)/SEG5
PIC16(L)F1934/6/7
DS41364E-page 10 2008-2011 Microchip Technology Inc.
Pin Diagram 44-Pin QFN (PIC16(L)F1934/7)
10
11
2
3
4
5
6
1
18
19
20
21
22
12
13
14
15
38
8
7
44
43
42
41
40
39
16
17
29
30
31
32
33
23
24
25
26
27
28
36
34
35
9
37
SEG7/C12IN1-/AN1/RA1
SEG12/VCAP(2)/SS(1)/SRNQ(1)/C2OUT(1)/C12IN0-/AN0/RA0
VPP/MCLR/RE3
VLCD3/P2A(1)/CCP2(1)/CPS3/C12IN2-/AN9/RB3
SEG13/ICDDAT/ICSPDAT/RB7
SEG14/ICDCLK/ICSPCLK/RB6
COM1/T1G(1)/P3A(1)/CCP3(1)/CPS5/AN13/RB5
COM0/CPS4/AN11/RB4
NC RC6/TX/CK/SEG9
RC5/SDO/SEG10
RC4/SDI/SDA/T1G(1)/SEG11
RD3/CPS11/P2C/SEG16
RD2/CPS10/P2B(1)
RD1/CPS9/CCP4
RD0/CPS8/COM3
RC3/SCL/SCK/SEG6
RC2/CCP1/P1A/SEG3
RC1/T1OSI/CCP2(1)/P2A(1)
RC0/T1OSO/T1CKI/P2B(1)
RA6/OSC2/CLKOUT/VCAP(2)/SEG1
RA7/OSC1/CLKIN/SEG2
VSS
VSS
NC
VDD
RE2/AN7/CCP5/SEG23
RE1/AN6/P3B/SEG22
RE0/AN5/CCP3(1)/P3A(1)/SEG21
RA5/AN4/C2OUT(1)/CPS7/SRNQ(1)/SS(1)/VCAP(2)/SEG5
RA4/C1OUT/CPS6/T0CKI/SRQ/SEG4
SEG8/DT/RX/RC7
SEG17/P2D/CPS12/RD4
SEG18/P1B/CPS13/RD5
SEG19/P1C/CPS14/RD6
SEG20/P1D/CPS15/RD7
VSS
VDD
VDD
SEG0/INT/SRI/CPS0/AN12/RB0
VLCD1/CPS1/C12IN3-/AN10/RB1
VLCD2/CPS2/AN8/RB2
44-pin QFN
PIC16F1934/7
PIC16LF1934/7
SEG15VREF+/C1IN+/AN3/RA3
COM2/DACOUT/VREF-/C2IN+/AN2/RA2
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/7 devices only.
2008-2011 Microchip Technology Inc. DS41364E-page 11
PIC16(L)F1934/6/7
Pin Diagram 44-Pin TQFP (PIC16(L)F1934/7)
44-pin TQFP
10
11
2
3
6
1
18
19
20
21
22
12
13
14
15
38
8
7
44
43
42
41
40
39
16
17
29
30
31
32
33
23
24
25
26
27
28
36
34
35
9
37
SEG15/VREF+/C1IN+/AN3/RA3
COM2/DACOUT/VREF-/C2IN+/AN2/RA2
SEG7/C12IN1-/AN1/RA1
SEG12/VCAP(2)/SS(1)/SRNQ(1)/C2OUT(1)/C12IN0-/AN0/RA0
VPP/MCLR/RE3
NC
SEG13/ICDDAT/ICSPDAT/RB7
SEG14/ICDCLK/ICSPCLK/RB6
COM1/T1G(1)/P3A(1)/CCP3(1)/CPS5/AN13/RB5
COM0/CPS4/AN11/RB4
NC
NC
NC
RC0/T1OSO/T1CKI/P2B(1)
VSS
VDD
SEG0/INT/SRI/CPS0/AN12/RB0
VLCD1/CPS1/C12IN3-/AN10/RB1
VLCD2/CPS2/AN8/RB2
VLCD3/P2A(1)/CCP2(1)/CPS3/C12IN2-/AN9/RB3
5
4PIC16F1934/7
PIC16LF1934/7
RA6/OSC2/CLKOUT/VCAP(2)/SEG1
RA7/OSC1/CLKIN/SEG2
VSS
VDD
RE2/AN7/CCP5/SEG23
RE1/AN6/P3B/SEG22
RE0/AN5/CCP3(1)/P3A(1)/SEG21
RA5/AN4/C2OUT(1)/CPS7/SRNQ(1)/SS(1)/VCAP(2)/SEG5
RA4/C1OUT/CPS6/T0CKI/SRQ/SEG4
SEG8/DT/RX/RC7
SEG17/P2D/CPS12/RD4
SEG18/P1B/CPS13/RD5
SEG19/P1C/CPS14/RD6
SEG20/P1D/CPS15/RD7
RC6/TX/CK/SEG9
RC5/SDO/SEG10
RC4/SDI/SDA/T1G(1)/SEG11
RD3/CPS11/P2C/SEG16
RD2/CPS10/P2B(1)
RD1/CPS9/CCP4
RD0/CPS8/COM3
RC3/SCL/SCK/SEG6
RC2/CCP1/P1A/SEG3
RC1/T1OSI/CCP2(1)/P2A(1)
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/7 devices only.
PIC16(L)F1934/6/7
DS41364E-page 12 2008-2011 Microchip Technology Inc.
TABLE 2: 40/44-PIN SUMMARY(PIC16(L)F1934/7)
I/O
40-Pin PDIP
40-Pin UQFN
44-Pin TQFP
44-Pin QFN
ANSEL
A/D
Cap Sense
Comparator
SR Lat ch
Timers
CCP
EUSART
MSSP
LCD
Interrupt
Pull-up
Basic
RA0 217 19 19 YAN0 C12IN0-/
C2OUT(1) SRNQ(1) SS(1) SEG12 VCAP
RA1 3 18 20 20 Y AN1 C12IN1- SEG7
RA2 419 21 21 YAN2/
VREF-
C2IN+/
DACOUT
COM2
RA3 5 20 22 22 Y AN3/
VREF+
—C1IN+ —SEG15
RA4 621 23 23 Y CPS6 C1OUT SRQ T0CKI SEG4
RA5 7 22 24 24 Y AN4 CPS7 C2OUT(1) SRNQ(1) ——SS
(1) SEG5 VCAP
RA6 14 29 31 33 SEG1 OSC2/
CLKOUT
VCAP
RA713283032————SEG2OSC1/
CLKIN
RB0 33 8 8 9 Y AN12 CPS0 SRI SEG0 INT/
IOC
Y
RB1 34 9 9 10 Y AN10 CPS1 C12IN3- VLCD1 IOC Y
RB2 35 10 10 11 YAN8 CPS2 VLCD2 IOC Y
RB3 36 11 11 12 Y AN9 CPS3 C12IN2- CCP2(1)/
P2A(1) VLCD3 IOC Y
RB4 37 12 14 14 YAN11 CPS4 COM0 IOC Y
RB5 38 13 15 15 Y AN13 CPS5 T1G(1) CCP3(1)/
P3A(1) ——COM1IOCY
RB6 39 14 16 16 SEG14 IOC YICSPCLK/
ICDCLK
RB740151717————SEG13IOCYICSPDAT/
ICDDAT
RC0 15 30 32 34 T1OSO/
T1CKI
P2B(1)
RC1 16 31 35 35 T1OSI CCP2(1)/
P2A(1) ——
RC2 17 32 36 36 CCP1/
P1A
SEG3
RC3 18 33 37 37 SCK/SCL SEG6
RC4 23 38 42 42 T1G(1) SDI/SDA SEG11
RC5 24 39 43 43 SDO SEG10
RC6 25 40 44 44 TX/CK SEG9
RC7 26 1 1 1 RX/DT SEG8
RD0 19 34 38 38 Y CPS8 COM3
RD1 20 35 39 39 Y CPS9 CCP4
RD2 21 36 40 40 Y CPS10 P2B(1)
RD3 22 37 41 41 Y CPS11 P2C SEG16
RD4 27 2 2 2 Y CPS12 P2D SEG17
RD5 28 3 3 3 Y CPS13 P1B SEG18
RD6 29 4 4 4 Y CPS14 P1C SEG19
RD7 30 5 5 5 Y CPS15 P1D SEG20
RE0 823 25 25 YAN5 CCP3(1)
P3A(1) SEG21
RE1 9 24 26 26 Y AN6 P3B SEG22
RE2 10 25 27 27 YAN7 CCP5 SEG23
RE3 1 16 18 18 Y MCLR/VPP
VDD 11,
32
7,
26
7,
28
7,8,
28
VDD
Vss 12,
31
6,
27
6,
29
6,30,
31
—— VSS
Note 1: Pin functions can be moved using the APFCON register.
2008-2011 Microchip Technology Inc. DS41364E-page 13
PIC16(L)F1934/6/7
Table of Contents
1.0 Device Overview ........................................................................................................................................................................ 15
2.0 Enhanced Mid-Range CPU ........................................................................................................................................................ 23
3.0 Memory Organization ................................................................................................................................................................. 25
4.0 Device Configuration .................................................................................................................................................................. 61
5.0 Oscillator Module (With Fail-Safe Clock Monitor)....................................................................................................................... 67
6.0 Resets ........................................................................................................................................................................................ 85
7.0 Interrupts .................................................................................................................................................................................... 93
8.0 Low Dropout (LDO) Voltage Regulator .................................................................................................................................... 107
9.0 Power-Down Mode (Sleep) ...................................................................................................................................................... 109
10.0 Watchdog Timer (WDT) ........................................................................................................................................................... 111
11.0 Data EEPROM and Flash Program Memory Control ............................................................................................................... 115
12.0 I/O Ports ................................................................................................................................................................................... 129
13.0 Interrupt-On-Change ................................................................................................................................................................ 151
14.0 Fixed Voltage Reference.......................................................................................................................................................... 155
15.0 Analog-to-Digital Converter (ADC) Module .............................................................................................................................. 157
16.0 Temperature Indicator Module ................................................................................................................................................. 171
17.0 Digital-to-Analog Converter (DAC) Module .............................................................................................................................. 173
18.0 Comparator Module.................................................................................................................................................................. 177
19.0 SR Latch................................................................................................................................................................................... 187
20.0 Timer0 Module ......................................................................................................................................................................... 191
21.0 Timer1 Module with Gate Control............................................................................................................................................. 197
22.0 Timer2/4/6 Modules.................................................................................................................................................................. 207
23.0 Capture/Compare/PWM Modules (ECCP1, ECCP2, ECCP3, CCP4, CCP5).......................................................................... 211
24.0 Master Synchronous Serial Port (MSSP) Module .................................................................................................................... 239
25.0 Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) ............................................................... 291
26.0 Capacitive Sensing Module...................................................................................................................................................... 319
27.0 Liquid Crystal Display (LCD) Driver Module............................................................................................................................. 327
28.0 In-Circuit Serial Programming™ (ICSP™) ............................................................................................................................... 361
29.0 Instruction Set Summary .......................................................................................................................................................... 365
30.0 Electrical Specifications............................................................................................................................................................ 379
31.0 DC and AC Characteristics Graphs and Charts ....................................................................................................................... 411
32.0 Development Support............................................................................................................................................................... 439
33.0 Packaging Information.............................................................................................................................................................. 443
Appendix A: Data Sheet Revision History.......................................................................................................................................... 459
Appendix B: Migrating From Other PIC® Devices.............................................................................................................................. 459
Index .................................................................................................................................................................................................. 461
The Microchip Web Site..................................................................................................................................................................... 469
Customer Change Notification Service .............................................................................................................................................. 469
Customer Support .............................................................................................................................................................................. 469
Reader Response .............................................................................................................................................................................. 470
Product Identification System ............................................................................................................................................................ 471
PIC16(L)F1934/6/7
DS41364E-page 14 2008-2011 Microchip Technology Inc.
TO OUR VALUED CUSTOMERS
It is our intention to provide our valued customers with the best documentation possible to ensure successful use of your Microchip
products. To this end, we will continue to improve our publications to better suit your needs. Our publications will be refined and
enhanced as new volumes and updates are introduced.
If you have any questions or comments regarding this publication, please contact the Marketing Communications Department via
E-mail at docerrors@microchip.com or fax the Reader Response Form in the back of this data sheet to (480) 792-4150. We
welcome your feedback.
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at:
http://www.microchip.com
You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page.
The last character of the literature number is the version number, (e.g., DS30000A is version A of document DS30000).
Errata
An errata sheet, describing minor operational differences from the data sheet and recommended workarounds, may exist for current
devices. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision
of silicon and revision of document to which it applies.
To determine if an errata sheet exists for a particular device, please check with one of the following:
Microchip’s Worldwide Web site; http://www.microchip.com
Your local Microchip sales office (see last page)
When contacting a sales office, please specify which device, revision of silicon and data sheet (include literature number) you are
using.
Customer No tific atio n Syst em
Register on our web site at www.microchip.com to receive the most current information on all of our products.
2008-2011 Microchip Technology Inc. DS41364E-page 15
PIC16(L)F1934/6/7
1.0 DEVICE OVERVIEW
The PIC16(L)F1934/6/7 are described within this data
sheet. They are available in 28/40/44-pin packages.
Figure 1-1 shows a block diagram of the
PIC16(L)F1934/6/7 devices. Ta bl e 1-2 shows the
pinout descriptions.
Reference Tab le 1-1 for peripherals available per
device.
TABLE 1-1: DEVICE PERIPHERAL
SUMMARY
Peripheral
PIC16F193X
PIC16LF193X
ADC ●●
Capacitive Sensing Module ●●
Digital-to-Analog Converter (DAC) ●●
EUSART ●●
Fixed Voltage Reference (FVR) ●●
LCD ●●
SR Latch ●●
Temperature Indicator ●●
Capture/Compare/PWM Modules
ECCP1 ●●
ECCP2 ●●
ECCP3 ●●
CCP4 ●●
CCP5 ●●
Comparators
C1 ●●
C2 ●●
Operational Amplifiers
OPA1 ●●
OPA2 ●●
Master Synchronous Serial Ports
MSSP1 ●●
Timers
Timer0 ●●
Timer1 ●●
Timer2 ●●
Timer4 ●●
Timer6 ●●
PIC16(L)F1934/6/7
DS41364E-page 16 2008-2011 Microchip Technology Inc.
FIGURE 1-1: PIC16(L)F1934/6/7 BLOCK DIAGRAM
PORTA
EUSART
Comparators
MSSP
Timer2Timer1 Timer4Timer0
ECCP1
ADC
10-Bit
ECCP2 ECCP3 CCP4 CCP5
Timer6
PORTB
PORTC
PORTD
PORTE
LCD
SR
Latch
Note 1: See applicable chapters for more information on peripherals.
CPU
Program
Flash Memory
EEPROM
RAM
Timing
Generation
INTRC
Oscillator
MCLR
Figure 2-1
OSC1/CLKIN
OSC2/CLKOUT
2008-2011 Microchip Technology Inc. DS41364E-page 17
PIC16(L)F1934/6/7
TABLE 1-2: PIC16(L)F1934/6/7 PINOUT DESCRIPTION
Name Function Input
Type Output
Type Description
RA0/AN0/C12IN0-/C2OUT(1)/
SRNQ(1)/SS(1)/VCAP(2)/SEG12
RA0 TTL CMOS General purpose I/O.
AN0 AN A/D Channel 0 input.
C12IN0- AN Comparator C1 or C2 negative input.
C2OUT CMOS Comparator C2 output.
SRNQ CMOS SR Latch inverting output.
SS ST Slave Select input.
VCAP Power Power Filter capacitor for Voltage Regulator (PIC16F1934/6/7 only).
SEG12 AN LCD Analog output.
RA1/AN1/C12IN1-/SEG7 RA1 TTL CMOS General purpose I/O.
AN1 AN A/D Channel 1 input.
C12IN1- AN Comparator C1 or C2 negative input.
SEG7 AN LCD Analog output.
RA2/AN2/C2IN+/VREF-/
DACOUT/COM2
RA2 TTL CMOS General purpose I/O.
AN2 AN A/D Channel 2 input.
C2IN+ AN Comparator C2 positive input.
VREF- AN A/D Negative Voltage Reference input.
DACOUT AN Voltage Reference output.
COM2 AN LCD Analog output.
RA3/AN3/C1IN+/VREF+/
COM3(3)/SEG15
RA3 TTL CMOS General purpose I/O.
AN3 AN A/D Channel 3 input.
C1IN+ AN Comparator C1 positive input.
VREF+ AN A/D Voltage Reference input.
COM3(3) AN LCD Analog output.
SEG15 AN LCD Analog output.
RA4/C1OUT/CPS6/T0CKI/SRQ/
CCP5/SEG4
RA4 TTL CMOS General purpose I/O.
C1OUT CMOS Comparator C1 output.
CPS6 AN Capacitive sensing input 6.
T0CKI ST Timer0 clock input.
SRQ CMOS SR Latch non-inverting output.
CCP5 ST CMOS Capture/Compare/PWM5.
SEG4 AN LCD Analog output.
RA5/AN4/C2OUT(1)/CPS7/
SRNQ(1)/SS(1)/VCAP(2)/SEG5
RA5 TTL CMOS General purpose I/O.
AN4 AN A/D Channel 4 input.
C2OUT CMOS Comparator C2 output.
CPS7 AN Capacitive sensing input 7.
SRNQ CMOS SR Latch inverting output.
SS ST Slave Select input.
VCAP Power Power Filter capacitor for Voltage Regulator (PIC16F1934/6/7 only).
SEG5 AN LCD Analog output.
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C™ = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/6/7 devices only.
3: PIC16(L)F1936 devices only.
4: PORTD is available on PIC16(L)F1934/7 devices only.
5: RE<2:0> are available on PIC16(L)F1934/7 devices only.
PIC16(L)F1934/6/7
DS41364E-page 18 2008-2011 Microchip Technology Inc.
RA6/OSC2/CLKOUT/VCAP(2)/
SEG1
RA6 TTL CMOS General purpose I/O.
OSC2 XTAL Crystal/Resonator (LP, XT, HS modes).
CLKOUT CMOS FOSC/4 output.
VCAP Power Power Filter capacitor for Voltage Regulator (PIC16F1934/6/7 only).
SEG1 AN LCD Analog output.
RA7/OSC1/CLKIN/SEG2 RA7 TTL CMOS General purpose I/O.
OSC1 XTAL Crystal/Resonator (LP, XT, HS modes).
CLKIN CMOS External clock input (EC mode).
SEG2 AN LCD Analog output.
RB0/AN12/CPS0/CCP4/SRI/INT/
SEG0
RB0 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN12 AN A/D Channel 12 input.
CPS0 AN Capacitive sensing input 0.
CCP4 ST CMOS Capture/Compare/PWM4.
SRI ST SR Latch input.
INT ST External interrupt.
SEG0 AN LCD analog output.
RB1/AN10/C12IN3-/CPS1/P1C/
VLCD1
RB1 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN10 AN A/D Channel 10 input.
C12IN3- AN Comparator C1 or C2 negative input.
CPS1 AN Capacitive sensing input 1.
P1C CMOS PWM output.
VLCD1 AN LCD analog input.
RB2/AN8/CPS2/P1B/VLCD2 RB2 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN8 AN A/D Channel 8 input.
CPS2 AN Capacitive sensing input 2.
P1B CMOS PWM output.
VLCD2 AN LCD analog input.
RB3/AN9/C12IN2-/CPS3/
CCP2(1)/P2A(1)/VLCD3
RB3 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN9 AN A/D Channel 9 input.
C12IN2- AN Comparator C1 or C2 negative input.
CPS3 AN Capacitive sensing input 3.
CCP2 ST CMOS Capture/Compare/PWM2.
P2A CMOS PWM output.
VLCD3 AN LCD analog input.
TABLE 1-2: PIC16(L)F1934/6/7 PINOUT DESCRIPTION (CONTINUED)
Name Function Input
Type Output
Type Description
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C™ = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/6/7 devices only.
3: PIC16(L)F1936 devices only.
4: PORTD is available on PIC16(L)F1934/7 devices only.
5: RE<2:0> are available on PIC16(L)F1934/7 devices only.
2008-2011 Microchip Technology Inc. DS41364E-page 19
PIC16(L)F1934/6/7
RB4/AN11/CPS4/P1D/COM0 RB4 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN11 AN A/D Channel 11 input.
CPS4 AN Capacitive sensing input 4.
P1D CMOS PWM output.
COM0 AN LCD Analog output.
RB5/AN13/CPS5/P2B/CCP3(1)/
P3A(1)/T1G(1)/COM1
RB5 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
AN13 AN A/D Channel 13 input.
CPS5 AN Capacitive sensing input 5.
P2B CMOS PWM output.
CCP3 ST CMOS Capture/Compare/PWM3.
P3A CMOS PWM output.
T1G ST Timer1 Gate input.
COM1 AN LCD Analog output.
RB6/ICSPCLK/ICDCLK/SEG14 RB6 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
ICSPCLK ST Serial Programming Clock.
ICDCLK ST In-Circuit Debug Clock.
SEG14 AN LCD Analog output.
RB7/ICSPDAT/ICDDAT/SEG13 RB7 TTL CMOS General purpose I/O. Individually controlled interrupt-on-change.
Individually enabled pull-up.
ICSPDAT ST CMOS ICSP™ Data I/O.
ICDDAT ST CMOS In-Circuit Data I/O.
SEG13 AN LCD Analog output.
RC0/T1OSO/T1CKI/P2B(1) RC0 ST CMOS General purpose I/O.
T1OSO XTAL XTAL Timer1 oscillator connection.
T1CKI ST Timer1 clock input.
P2B CMOS PWM output.
RC1/T1OSI/CCP2(1)/P2A(1) RC1 ST CMOS General purpose I/O.
T1OSI XTAL XTAL Timer1 oscillator connection.
CCP2 ST CMOS Capture/Compare/PWM2.
P2A CMOS PWM output.
RC2/CCP1/P1A/SEG3 RC2 ST CMOS General purpose I/O.
CCP1 ST CMOS Capture/Compare/PWM1.
P1A CMOS PWM output.
SEG3 AN LCD Analog output.
RC3/SCK/SCL/SEG6 RC3 ST CMOS General purpose I/O.
SCK ST CMOS SPI clock.
SCL I2CODI
2C™ clock.
SEG6 AN LCD Analog output.
TABLE 1-2: PIC16(L)F1934/6/7 PINOUT DESCRIPTION (CONTINUED)
Name Function Input
Type Output
Type Description
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C™ = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/6/7 devices only.
3: PIC16(L)F1936 devices only.
4: PORTD is available on PIC16(L)F1934/7 devices only.
5: RE<2:0> are available on PIC16(L)F1934/7 devices only.
PIC16(L)F1934/6/7
DS41364E-page 20 2008-2011 Microchip Technology Inc.
RC4/SDI/SDA/T1G(1)/SEG11 RC4 ST CMOS General purpose I/O.
SDI ST SPI data input.
SDA I2CODI
2C™ data input/output.
T1G ST Timer1 Gate input.
SEG11 AN LCD Analog output.
RC5/SDO/SEG10 RC5 ST CMOS General purpose I/O.
SDO CMOS SPI data output.
SEG10 AN LCD Analog output.
RC6/TX/CK/CCP3/P3A/SEG9 RC6 ST CMOS General purpose I/O.
TX CMOS USART asynchronous transmit.
CK ST CMOS USART synchronous clock.
CCP3 ST CMOS Capture/Compare/PWM3.
P3A CMOS PWM output.
SEG9 AN LCD Analog output.
RC7/RX/DT/P3B/SEG8 RC7 ST CMOS General purpose I/O.
RX ST USART asynchronous input.
DT ST CMOS USART synchronous data.
P3B CMOS PWM output.
SEG8 AN LCD Analog output.
RD0(4)/CPS8/COM3 RD0 ST CMOS General purpose I/O.
CPS8 AN Capacitive sensing input 8.
COM3 AN LCD analog output.
RD1(4)/CPS9/CCP4 RD1 ST CMOS General purpose I/O.
CPS9 AN Capacitive sensing input 9.
CCP4 ST CMOS Capture/Compare/PWM4.
RD2(4)/CPS10/P2B RD2 ST CMOS General purpose I/O.
CPS10 AN Capacitive sensing input 10.
P2B CMOS PWM output.
RD3(4)/CPS11/P2C/SEG16 RD3 ST CMOS General purpose I/O.
CPS11 AN Capacitive sensing input 11.
P2C CMOS PWM output.
SEG16 AN LCD analog output.
RD4(4)/CPS12/P2D/SEG17 RD4 ST CMOS General purpose I/O.
CPS12 AN Capacitive sensing input 12.
P2D CMOS PWM output.
SEG17 AN LCD analog output.
RD5(4)/CPS13/P1B/SEG18 RD5 ST CMOS General purpose I/O.
CPS13 AN Capacitive sensing input 13.
P1D CMOS PWM output.
SEG18 AN LCD analog output.
TABLE 1-2: PIC16(L)F1934/6/7 PINOUT DESCRIPTION (CONTINUED)
Name Function Input
Type Output
Type Description
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C™ = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/6/7 devices only.
3: PIC16(L)F1936 devices only.
4: PORTD is available on PIC16(L)F1934/7 devices only.
5: RE<2:0> are available on PIC16(L)F1934/7 devices only.
2008-2011 Microchip Technology Inc. DS41364E-page 21
PIC16(L)F1934/6/7
RD6(4)/CPS14/P1C/SEG19 RD6 ST CMOS General purpose I/O.
CPS14 AN Capacitive sensing input 14.
P1C CMOS PWM output.
SEG19 AN LCD analog output.
RD7(4)/CPS15/P1D/SEG20 RD7 ST CMOS General purpose I/O.
CPS15 AN Capacitive sensing input 15.
P1D CMOS PWM output.
SEG20 AN LCD analog output.
RE0(5)/AN5/P3A(1)/CCP3(1)/
SEG21
RE0 ST CMOS General purpose I/O.
AN5 AN A/D Channel 5 input.
P3A CMOS PWM output.
CCP3 ST CMOS Capture/Compare/PWM3.
SEG21 AN LCD analog output.
RE1(5)/AN6/P3B/SEG22 RE1 ST CMOS General purpose I/O.
AN6 AN A/D Channel 6 input.
P3B CMOS PWM output.
SEG22 AN LCD analog output.
RE2(5)/AN7/CCP5/SEG23 RE2 ST CMOS General purpose I/O.
AN7 AN A/D Channel 7 input.
CCP5 ST CMOS Capture/Compare/PWM5.
SEG23 AN LCD analog output.
RE3/MCLR/VPP RE3 TTL General purpose input.
MCLR ST Master Clear with internal pull-up.
VPP HV Programming voltage.
VDD VDD Power Positive supply.
VSS VSS Power Ground reference.
TABLE 1-2: PIC16(L)F1934/6/7 PINOUT DESCRIPTION (CONTINUED)
Name Function Input
Type Output
Type Description
Legend: AN = Analog input or output CMOS = CMOS compatible input or output OD = Open Drain
TTL = TTL compatible input ST = Schmitt Trigger input with CMOS levels I2C™ = Schmitt Trigger input with I2C
HV = High Voltage XTAL = Crystal levels
Note 1: Pin function is selectable via the APFCON register.
2: PIC16F1934/6/7 devices only.
3: PIC16(L)F1936 devices only.
4: PORTD is available on PIC16(L)F1934/7 devices only.
5: RE<2:0> are available on PIC16(L)F1934/7 devices only.
PIC16(L)F1934/6/7
DS41364E-page 22 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 23
PIC16(L)F1934/6/7
2.0 ENHANCED MID-RANGE CPU
This family of devices contain an enhanced mid-range
8-bit CPU core. The CPU has 49 instructions. Interrupt
capability includes automatic context saving. The
hardware stack is 16 levels deep and has Overflow and
Underflow Reset capability. Direct, Indirect, and
Relative Addressing modes are available. Two File
Select Registers (FSRs) provide the ability to read
program and data memory.
Automatic Interrupt Context Saving
16-level Stack with Overflow and Underflow
File Select Registers
Instruction Set
2.1 Automatic Interrupt Context
Saving
During interrupts, certain registers are automatically
saved in shadow registers and restored when returning
from the interrupt. This saves stack space and user
code. See Section 7.5 “Automatic Context Saving”,
for more information.
2.2 16-level Stack with Overflow and
Underflow
These devices have an external stack memory 15 bits
wide and 16 words deep. A Stack Overflow or Under-
flow will set the appropriate bit (STKOVF or STKUNF)
in the PCON register, and if enabled will cause a soft-
ware Reset. See section Section 3.4 “St ack” for more
details.
2.3 File Select Registers
There are two 16-bit File Select Registers (FSR). FSRs
can access all file registers and program memory,
which allows one Data Pointer for all memory. When an
FSR points to program memory, there is 1 additional
instruction cycle in instructions using INDF to allow the
data to be fetched. General purpose memory can now
also be addressed linearly, providing the ability to
access contiguous data larger than 80 bytes. There are
also new instructions to support the FSRs. See
Section 3.5 “Indirect Addressing” for more details.
2.4 Instruction Set
There are 49 instructions for the enhanced mid-range
CPU to support the features of the CPU. See
Section 29.0 “Instruction Set Summary for more
details.
PIC16(L)F1934/6/7
DS41364E-page 24 2008-2011 Microchip Technology Inc.
FIGURE 2-1: CORE BLOCK DIAGRAM
Data Bus 8
14
Program
Bus
Instruction reg
Program Counter
8 Level Stack
(13-bit)
Direct Addr 7
9
Addr MUX
FSR reg
STATUS reg
MUX
ALU
Power-up
Timer
Oscillator
Start-up Timer
Power-on
Reset
Watchdog
Timer
Instruction
Decode &
Control
Timing
Generation
OSC1/CLKIN
OSC2/CLKOUT
VDD
8
8
Brown-out
Reset
12
3
VSS
Internal
Oscillator
Block
Configuration
Data Bus 8
14
Program
Bus
Instruction reg
Program Counter
8 Level Stack
(13-bit)
Direct Addr 7
Addr MUX
FSR reg
STATUS reg
MUX
ALU
W reg
Instruction
Decode &
Control
Timing
Generation
VDD
8
8
3
VSS
Internal
Oscillator
Block
Configuration
15 Data Bus 8
14
Program
Bus
Instruction Reg
Program Counter
16-Level Stack
(15-bit)
Direct Addr 7
RAM Addr
Addr MUX
Indirect
Addr
FSR0 Reg
STATUS Reg
MUX
ALU
Instruction
Decode and
Control
Timing
Generation
VDD
8
8
3
VSS
Internal
Oscillator
Block
Configuration
Flash
Program
Memory RAM
FSR regFSR reg
FSR1 Reg
15
15
MUX
15
Program Memory
Read (PMR)
12
2008-2011 Microchip Technology Inc. DS41364E-page 25
PIC16(L)F1934/6/7
3.0 MEMORY ORGANIZATION
There are three types of memory in PIC16(L)F1934/6/7
devices: Data Memory, Program Memory and Data
EEPROM Memory(1).
Program Memory
Data Memory
- Core Registers
- Special Function Registers
- General Purpose RAM
- Common RAM
- Device Memory Maps
- Special Function Registers Summary
Data EEPROM memory(1)
The following features are associated with access and
control of program memory and data memory:
PCL and PCLATH
•Stack
Indirect Addressing
3.1 Program Memory Organization
The enhanced mid-range core has a 15-bit program
counter capable of addressing 32K x 14 program
memory space. Table 3-1 shows the memory sizes
implemented for the PIC16(L)F1934/6/7 family.
Accessing a location above these boundaries will cause
a wrap-around within the implemented memory space.
The Reset vector is at 0000h and the interrupt vector is
at 0004h (see Figures 3-1 and 3-2).
Note 1: The data EEPROM memory and the
method to access Flash memory through
the EECON registers is described in
Section 1 1.0 “Dat a EEPROM and Flash
Program Memory Control”.
TABLE 3-1: DEVICE SIZES AND ADDRESSES
Device Program Memory Space (Words) Last Program Memory Address
PIC16F1934/PIC16LF1934 4,096 0FFFh
PIC16F1936/PIC16LF1936 8,192 1FFFh
PIC16F1937/PIC16LF1937 8,192 1FFFh
PIC16(L)F1934/6/7
DS41364E-page 26 2008-2011 Microchip Technology Inc.
FIGURE 3-1: PROGRAM MEMORY MAP
AND STACK FOR
4KW PARTS
FIGURE 3-2: PROGRAM MEMORY MAP
AND STACK FOR
8KW PARTS
PC<14:0>
15
0000h
0004h
Stack Level 0
Stack Level 15
Reset Vector
Interrupt Vector
CALL, CALLW
RETURN, RETLW
Stack Level 1
0005h
On-chip
Program
Memory
Page 0
07FFh
Rollover to Page 0
0800h
0FFFh
1000h
7FFFh
Page 1
Rollover to Page 1
Interrupt, RETFIE
PC<14:0>
15
0000h
0004h
Stack Level 0
Stack Level 15
Reset Vector
Interrupt Vector
Stack Level 1
0005h
On-chip
Program
Memory
Page 0
07FFh
Rollover to Page 0
0800h
0FFFh
1000h
7FFFh
Page 1
Rollover to Page 3
Page 2
Page 3
17FFh
1800h
1FFFh
2000h
CALL, CALLW
RETURN, RETLW
Interrupt, RETFIE
2008-2011 Microchip Technology Inc. DS41364E-page 27
PIC16(L)F1934/6/7
3.1.1 READING PROGRAM MEMORY AS
DATA
There are two methods of accessing constants in pro-
gram memory. The first method is to use tables of
RETLW instructions. The second method is to set an
FSR to point to the program memory.
3.1.1.1 RETLW Instruction
The RETLW instruction can be used to provide access
to tables of constants. The recommended way to create
such a table is shown in Example 3-1.
EXAMPL E 3-1: RETLW INSTRUCTION
The BRW instruction makes this type of table very sim-
ple to implement. If your code must remain portable
with previous generations of microcontrollers, then the
BRW instruction is not available so the older table read
method must be used.
constants
BRW ;Add Index in W to
;program counter to
;select data
RETLW DATA0 ;Index0 data
RETLW DATA1 ;Index1 data
RETLW DATA2
RETLW DATA3
my_function
;… LOTS OF CODE…
MOVLW DATA_INDEX
call constants
;… THE CONSTANT IS IN W
PIC16(L)F1934/6/7
DS41364E-page 28 2008-2011 Microchip Technology Inc.
3.1.1.2 Indirect Read with FSR
The program memory can be accessed as data by set-
ting bit 7 of the FSRxH register and reading the match-
ing INDFx register. The MOVIW instruction will place the
lower 8 bits of the addressed word in the W register.
Writes to the program memory cannot be performed via
the INDF registers. Instructions that access the pro-
gram memory via the FSR require one extra instruction
cycle to complete. Example 3-2 demonstrates access-
ing the program memory via an FSR.
The HIGH directive will set bit<7> if a label points to a
location in program memory.
EXAMPLE 3-2: ACCESSING PROGRAM
MEMORY VIA FSR
3.2 Data Memor y Organization
The data memory is partitioned in 32 memory banks
with 128 bytes in a bank. Each bank consists of
(Figure 3-3):
12 core registers
20 Special Function Registers (SFR)
Up to 80 bytes of General Purpose RAM (GPR)
16 bytes of common RAM
The active bank is selected by writing the bank number
into the Bank Select Register (BSR). Unimplemented
memory will read as0’. All data memory can be
accessed either directly (via instructions that use the
file registers) or indirectly via the two File Select
Registers (FSR). See Section 3.5 “Indirect
Addressing for more information.
3.2.1 CORE REGISTERS
The core registers contain the registers that directly
affect the basic operation of the PIC16(L)F1934/6/7.
These registers are listed below:
INDF0
INDF1
•PCL
•STATUS
•FSR0 Low
FSR0 High
•FSR1 Low
FSR1 High
BSR
•WREG
•PCLATH
INTCON
constants
RETLW DATA0 ;Index0 data
RETLW DATA1 ;Index1 data
RETLW DATA2
RETLW DATA3
my_function
;… LOTS OF CODE…
MOVLW LOW constants
MOVWF FSR1L
MOVLW HIGH constants
MOVWF FSR1H
MOVIW 0[FSR1]
;THE PROGRAM MEMORY IS IN W
Note: The core registers are the first 12
addresses of every data memory bank.
2008-2011 Microchip Technology Inc. DS41364E-page 29
PIC16(L)F1934/6/7
3.2.1.1 STATUS Register
The STATUS register, shown in Register 3-1, contains:
the arithmetic status of the ALU
the Reset status
The STATUS register can be the destination for any
instruction, like any other register. If the STATUS
register is the destination for an instruction that affects
the Z, DC or C bits, then the write to these three bits is
disabled. These bits are set or cleared according to the
device logic. Furthermore, the TO and PD bits are not
writable. Therefore, the result of an instruction with the
STATUS register as destination may be different than
intended.
For example, CLRF STATUS will clear the upper three
bits and set the Z bit. This leaves the STATUS register
as ‘000u u1uu’ (where u = unchanged).
It is recommended, therefore, that only BCF, BSF,
SWAPF and MOVWF instructions are used to alter the
STATUS register, because these instructions do not
affect any Status bits. For other instructions not
affecting any Status bits (Refer to Section 29.0
“Instruction Set Summary”).
Note 1: The C and DC bits operate as Borrow
and Digit Borrow out bits, respectively, in
subtraction.
REGISTER 3-1: STATUS: STATUS REGISTER
U-0 U-0 U-0 R-1/q R-1/q R/W-0/u R/W-0/u R/W-0/u
TO PD ZDC
(1) C(1)
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition
bit 7-5 Unimplemented: Read as ‘0
bit 4 TO: Time-out bit
1 = After power-up, CLRWDT instruction or SLEEP instruction
0 = A WDT time-out occurred
bit 3 PD: Power-down bit
1 = After power-up or by the CLRWDT instruction
0 = By execution of the SLEEP instruction
bit 2 Z: Zero bit
1 = The result of an arithmetic or logic operation is zero
0 = The result of an arithmetic or logic operation is not zero
bit 1 DC: Digit Carry/Digit Borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions)(1)
1 = A carry-out from the 4th low-order bit of the result occurred
0 = No carry-out from the 4th low-order bit of the result
bit 0 C: Carry/Borrow bit(1) (ADDWF, ADDLW, SUBLW, SUBWF instructions)(1)
1 = A carry-out from the Most Significant bit of the result occurred
0 = No carry-out from the Most Significant bit of the result occurred
Note 1: For Borrow, the polarity is reversed. A subtraction is executed by adding the two’s complement of the
second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high-order or low-order
bit of the source register.
PIC16(L)F1934/6/7
DS41364E-page 30 2008-2011 Microchip Technology Inc.
3.2.2 SPECIAL FUNCTION REGISTER
The Special Function Registers (SFR) are registers
used by the application to control the desired operation
of peripheral functions in the device. The registers
associated with the operation of the peripherals are
described in the appropriate peripheral chapter of this
data sheet.
3.2.3 GENERAL PURPOSE RAM
There are up to 80 bytes of GPR in each data memory
bank.
3.2.3.1 Linear Access to GPR
The general purpose RAM can be accessed in a
non-banked method via the FSRs. This can simplify
access to large memory structures. See Section 3.5.2
“Linear Data Memory” for more information.
3.2.4 COMMON RAM
There are 16 bytes of common RAM accessible from all
banks.
FIGURE 3-3: BANKED MEM ORY
PARTITIONING
3.2.5 DEVICE MEMORY MAPS
The memory maps for the device family are as shown
in Table 3-2.
0Bh
0Ch
1Fh
20h
6Fh
70h
7Fh
00h
Common RAM
(16 bytes)
General Purpose RAM
(80 bytes maximum)
Core Registers
(12 bytes)
Special Function Registers
(20 bytes maximum)
Memory Region
7-bit Bank Offset
TABLE 3-2: MEMORY MAP TABLES
Device Banks Table No.
PIC16F1934
PIC16LF1934
0-7 Table 3-3
8-15 Tabl e 3 - 4 ,Tab l e 3 -1 0
16-23 Table 3-7
23-31 Table 3-8, Ta b le 3 - 11
PIC16F1936
PIC16LF1936
0-7 Table 3-5
8-15 Table 3-6, Tabl e 3- 9
16-23 Table 3-7
23-31 Table 3-8, Ta b le 3 - 11
PIC16F1937
PIC16LF1937
0-7 Table 3-5
8-15 Tabl e 3-6, Table 3-10
16-23 Table 3-7
23-31 Table 3-8, Ta b le 3 - 11
PIC16(L)F1934/6/7
DS41364E-page 31 2008-2011 Microchip Technology Inc.
TABLE 3-3: PIC16(L)F1934 MEMORY MAP, BANKS 0-7
Legend: = Unimplemented data memory locations, read as ‘0’.
Note 1: Not available on PIC16(L)F1936.
BANK 0 BANK 1 BANK 2 BANK 3 BANK 4 BANK 5 BANK 6 BANK 7
000h INDF0 080h INDF0 100h INDF0 180h INDF0 200h INDF0 280h INDF0 300h INDF0 380h INDF0
001h INDF1 081h INDF1 101h INDF1 181h INDF1 201h INDF1 281h INDF1 301h INDF1 381h INDF1
002h PCL 082h PCL 102h PCL 182h PCL 202h PCL 282h PCL 302h PCL 382h PCL
003h STATUS 083h STATUS 103h STATUS 183h STATUS 203h STATUS 283h STATUS 303h STATUS 383h STATUS
004h FSR0L 084h FSR0L 104h FSR0L 184h FSR0L 204h FSR0L 284h FSR0L 304h FSR0L 384h FSR0L
005h FSR0H 085h FSR0H 105h FSR0H 185h FSR0H 205h FSR0H 285h FSR0H 305h FSR0H 385h FSR0H
006h FSR1L 086h FSR1L 106h FSR1L 186h FSR1L 206h FSR1L 286h FSR1L 306h FSR1L 386h FSR1L
007h FSR1H 087h FSR1H 107h FSR1H 187h FSR1H 207h FSR1H 287h FSR1H 307h FSR1H 387h FSR1H
008h BSR 088h BSR 108h BSR 188h BSR 208h BSR 288h BSR 308h BSR 388h BSR
009h WREG 089h WREG 109h WREG 189h WREG 209h WREG 289h WREG 309h WREG 389h WREG
00Ah PCLATH 08Ah PCLATH 10Ah PCLATH 18Ah PCLATH 20Ah PCLATH 28Ah PCLATH 30Ah PCLATH 38Ah PCLATH
00Bh INTCON 08Bh INTCON 10Bh INTCON 18Bh INTCON 20Bh INTCON 28Bh INTCON 30Bh INTCON 38Bh INTCON
00Ch PORTA 08Ch TRISA 10Ch LATA 18Ch ANSELA 20Ch 28Ch 30Ch 38Ch
00Dh PORTB 08Dh TRISB 10Dh LATB 18Dh ANSELB 20Dh WPUB 28Dh 30Dh 38Dh
00Eh PORTC 08Eh TRISC 10Eh LATC 18Eh —20Eh—28Eh—30Eh—38Eh
00Fh PORTD(1) 08Fh TRISD(1) 10Fh LATD(1) 18Fh ANSELD(1) 20Fh —28Fh—30Fh—38Fh
010h PORTE 090h TRISE 110h LATE(1) 190h ANSELE(1) 210h WPUE 290h 310h 390h
011h PIR1 091h PIE1 111h CM1CON0 191h EEADRL 211h SSPBUF 291h CCPR1L 311h CCPR3L 391h
012h PIR2 092h PIE2 112h CM1CON1 192h EEADRH 212h SSPADD 292h CCPR1H 312h CCPR3H 392h
013h PIR3 093h PIE3 113h CM2CON0 193h EEDATL 213h SSPMSK 293h CCP1CON 313h CCP3CON 393h
014h —094h 114h CM2CON1 194h EEDATH 214h SSPSTAT 294h PWM1CON 314h PWM3CON 394h IOCBP
015h TMR0 095h OPTION_REG 115h CMOUT 195h EECON1 215h SSPCON1 295h CCP1AS 315h CCP3AS 395h IOCBN
016h TMR1L 096h PCON 116h BORCON 196h EECON2 216h SSPCON2 296h PSTR1CON 316h PSTR3CON 396h IOCBF
017h TMR1H 097h WDTCON 117h FVRCON 197h 217h SSPCON3 297h 317h 397h
018h T1CON 098h OSCTUNE 118h DACCON0 198h —218h 298h CCPR2L 318h CCPR4L 398h
019h T1GCON 099h OSCCON 119h DACCON1 199h RCREG 219h 299h CCPR2H 319h CCPR4H 399h
01Ah TMR2 09Ah OSCSTAT 11Ah SRCON0 19Ah TXREG 21Ah 29Ah CCP2CON 31Ah CCP4CON 39Ah
01Bh PR2 09Bh ADRESL 11Bh SRCON1 19Bh SPBRGL 21Bh 29Bh PWM2CON 31Bh —39Bh
01Ch T2CON 09Ch ADRESH 11Ch 19Ch SPBRGH 21Ch 29Ch CCP2AS 31Ch CCPR5L 39Ch
01Dh 09Dh ADCON0 11Dh APFCON 19Dh RCSTA 21Dh 29Dh PSTR2CON 31Dh CCPR5H 39Dh
01Eh CPSCON0 09Eh ADCON1 11Eh 19Eh TXSTA 21Eh 29Eh CCPTMRS0 31Eh CCP5CON 39Eh
01Fh CPSCON1 09Fh —11Fh 19Fh BAUDCTR 21Fh 29Fh CCPTMRS1 31Fh —39Fh
020h
General
Purpose
Register
96 Bytes
0A0h
General
Purpose
Register
80 Bytes
120h
General
Purpose
Register
80 Bytes
1A0h
Unimplemented
Read as ‘0
220h
Unimplemented
Read as ‘0
2A0h
Unimplemented
Read as ‘0
320h
Unimplemented
Read as ‘0
3A0h
Unimplemented
Read as ‘0
06Fh 0EFh 16Fh 1EFh 26Fh 2EFh 36Fh 3EFh
070h 0F0h
Accesses
70h – 7Fh
170h
Accesses
70h – 7Fh
1F0h
Accesses
70h – 7Fh
270h
Accesses
70h – 7Fh
2F0h
Accesses
70h – 7Fh
370h
Accesses
70h – 7Fh
3F0h
Accesses
70h – 7Fh
07Fh 0FFh 17Fh 1FFh 27Fh 2FFh 37Fh 3FFh
PIC16(L)F1934/6/7
DS41364E-page 32 2008-2011 Microchip Technology Inc.
TABLE 3-4: PIC16(L)F1934 MEMORY MAP, BANKS 8-15
Legend: = Unimplemented data memory locations, read as ‘0’.
BANK 8 BANK 9 BANK 10 BANK 11 BANK 12 BANK 13 BANK 14 BANK 15
400h INDF0 480h INDF0 500h INDF0 580h INDF0 600h INDF0 680h INDF0 700h INDF0 780h INDF0
401h INDF1 481h INDF1 501h INDF1 581h INDF1 601h INDF1 681h INDF1 701h INDF1 781h INDF1
402h PCL 482h PCL 502h PCL 582h PCL 602h PCL 682h PCL 702h PCL 782h PCL
403h STATUS 483h STATUS 503h STATUS 583h STATUS 603h STATUS 683h STATUS 703h STATUS 783h STATUS
404h FSR0L 484h FSR0L 504h FSR0L 584h FSR0L 604h FSR0L 684h FSR0L 704h FSR0L 784h FSR0L
405h FSR0H 485h FSR0H 505h FSR0H 585h FSR0H 605h FSR0H 685h FSR0H 705h FSR0H 785h FSR0H
406h FSR1L 486h FSR1L 506h FSR1L 586h FSR1L 606h FSR1L 686h FSR1L 706h FSR1L 786h FSR1L
407h FSR1H 487h FSR1H 507h FSR1H 587h FSR1H 607h FSR1H 687h FSR1H 707h FSR1H 787h FSR1H
408h BSR 488h BSR 508h BSR 588h BSR 608h BSR 688h BSR 708h BSR 788h BSR
409h WREG 489h WREG 509h WREG 589h WREG 609h WREG 689h WREG 709h WREG 789h WREG
40Ah PCLATH 48Ah PCLATH 50Ah PCLATH 58Ah PCLATH 60Ah PCLATH 68Ah PCLATH 70Ah PCLATH 78Ah PCLATH
40Bh INTCON 48Bh INTCON 50Bh INTCON 58Bh INTCON 60Bh INTCON 68Bh INTCON 70Bh INTCON 78Bh INTCON
40Ch 48Ch 50Ch 58Ch 60Ch 68Ch 70Ch 78Ch
40Dh 48Dh 50Dh 58Dh 60Dh 68Dh 70Dh 78Dh
40Eh 48Eh 50Eh 58Eh 60Eh 68Eh 70Eh 78Eh
40Fh 48Fh 50Fh 58Fh 60Fh 68Fh 70Fh 78Fh
410h 490h 510h 590h 610h 690h 710h 790h
411h 491h 511h 591h 611h 691h 711h 791h
See Ta bl e 3 - 9 or
Tab l e 3 -1 0
412h 492h 512h 592h 612h 692h 712h 792h
413h 493h 513h 593h 613h 693h 713h 793h
414h 494h 514h 594h 614h 694h 714h 794h
415h TMR4 495h 515h 595h 615h 695h 715h 795h
416h PR4 496h 516h 596h 616h 696h 716h 796h
417h T4CON 497h 517h 597h 617h 697h 717h 797h
418h 498h 518h 598h 618h 698h 718h 798h
419h 499h 519h 599h 619h 699h 719h 799h
41Ah 49Ah 51Ah 59Ah 61Ah 69Ah 71Ah 79Ah
41Bh 49Bh 51Bh 59Bh 61Bh 69Bh 71Bh 79Bh
41Ch TMR6 49Ch 51Ch 59Ch 61Ch 69Ch 71Ch 79Ch
41Dh PR6 49Dh 51Dh 59Dh 61Dh 69Dh 71Dh 79Dh
41Eh T6CON 49Eh 51Eh 59Eh 61Eh 69Eh 71Eh 79Eh
41Fh 49Fh 51Fh 59Fh 61Fh 69Fh 71Fh 79Fh
420h
Unimplemented
Read as ‘0
4A0h
Unimplemented
Read as ‘0
520h
Unimplemented
Read as ‘0
5A0h
Unimplemented
Read as ‘0
620h
Unimplemented
Read as ‘0
6A0h
Unimplemented
Read as ‘0
720h
Unimplemented
Read as ‘0
7A0h
46Fh 4EFh 56Fh 5EFh 66Fh 6EFh 76Fh 7EFh
470h
Accesses
70h – 7Fh
4F0h
Accesses
70h – 7Fh
570h
Accesses
70h – 7Fh
5F0h
Accesses
70h – 7Fh
670h
Accesses
70h – 7Fh
6F0h
Accesses
70h – 7Fh
770h
Accesses
70h – 7Fh
7F0h
Accesses
70h – 7Fh
47Fh 4FFh 57Fh 5FFh 67Fh 6FFh 77Fh 7FFh
PIC16(L)F1934/6/7
DS41364E-page 33 2008-2011 Microchip Technology Inc.
TABLE 3-5: PIC16(L)F1936/1937 MEMORY MAP, BANKS 0-7
Legend: = Unimplemented data memory locations, read as ‘0’.
Note 1: Not available on PIC16(L)F1936.
BANK 0 BANK 1 BANK 2 BANK 3 BANK 4 BANK 5 BANK 6 BANK 7
000h INDF0 080h INDF0 100h INDF0 180h INDF0 200h INDF0 280h INDF0 300h INDF0 380h INDF0
001h INDF1 081h INDF1 101h INDF1 181h INDF1 201h INDF1 281h INDF1 301h INDF1 381h INDF1
002h PCL 082h PCL 102h PCL 182h PCL 202h PCL 282h PCL 302h PCL 382h PCL
003h STATUS 083h STATUS 103h STATUS 183h STATUS 203h STATUS 283h STATUS 303h STATUS 383h STATUS
004h FSR0L 084h FSR0L 104h FSR0L 184h FSR0L 204h FSR0L 284h FSR0L 304h FSR0L 384h FSR0L
005h FSR0H 085h FSR0H 105h FSR0H 185h FSR0H 205h FSR0H 285h FSR0H 305h FSR0H 385h FSR0H
006h FSR1L 086h FSR1L 106h FSR1L 186h FSR1L 206h FSR1L 286h FSR1L 306h FSR1L 386h FSR1L
007h FSR1H 087h FSR1H 107h FSR1H 187h FSR1H 207h FSR1H 287h FSR1H 307h FSR1H 387h FSR1H
008h BSR 088h BSR 108h BSR 188h BSR 208h BSR 288h BSR 308h BSR 388h BSR
009h WREG 089h WREG 109h WREG 189h WREG 209h WREG 289h WREG 309h WREG 389h WREG
00Ah PCLATH 08Ah PCLATH 10Ah PCLATH 18Ah PCLATH 20Ah PCLATH 28Ah PCLATH 30Ah PCLATH 38Ah PCLATH
00Bh INTCON 08Bh INTCON 10Bh INTCON 18Bh INTCON 20Bh INTCON 28Bh INTCON 30Bh INTCON 38Bh INTCON
00Ch PORTA 08Ch TRISA 10Ch LATA 18Ch ANSELA 20Ch 28Ch 30Ch 38Ch
00Dh PORTB 08Dh TRISB 10Dh LATB 18Dh ANSELB 20Dh WPUB 28Dh 30Dh 38Dh
00Eh PORTC 08Eh TRISC 10Eh LATC 18Eh —20Eh—28Eh—30Eh—38Eh
00Fh PORTD(1) 08Fh TRISD(1) 10Fh LATD(1) 18Fh ANSELD(1) 20Fh —28Fh—30Fh—38Fh
010h PORTE 090h TRISE 110h LATE(1) 190h ANSELE(1) 210h WPUE 290h 310h 390h
011h PIR1 091h PIE1 111h CM1CON0 191h EEADRL 211h SSPBUF 291h CCPR1L 311h CCPR3L 391h
012h PIR2 092h PIE2 112h CM1CON1 192h EEADRH 212h SSPADD 292h CCPR1H 312h CCPR3H 392h
013h PIR3 093h PIE3 113h CM2CON0 193h EEDATL 213h SSPMSK 293h CCP1CON 313h CCP3CON 393h
014h —094h 114h CM2CON1 194h EEDATH 214h SSPSTAT 294h PWM1CON 314h PWM3CON 394h IOCBP
015h TMR0 095h OPTION_REG 115h CMOUT 195h EECON1 215h SSPCON1 295h CCP1AS 315h CCP3AS 395h IOCBN
016h TMR1L 096h PCON 116h BORCON 196h EECON2 216h SSPCON2 296h PSTR1CON 316h PSTR3CON 396h IOCBF
017h TMR1H 097h WDTCON 117h FVRCON 197h 217h SSPCON3 297h 317h 397h
018h T1CON 098h OSCTUNE 118h DACCON0 198h —218h 298h CCPR2L 318h CCPR4L 398h
019h T1GCON 099h OSCCON 119h DACCON1 199h RCREG 219h 299h CCPR2H 319h CCPR4H 399h
01Ah TMR2 09Ah OSCSTAT 11Ah SRCON0 19Ah TXREG 21Ah 29Ah CCP2CON 31Ah CCP4CON 39Ah
01Bh PR2 09Bh ADRESL 11Bh SRCON1 19Bh SPBRGL 21Bh 29Bh PWM2CON 31Bh —39Bh
01Ch T2CON 09Ch ADRESH 11Ch 19Ch SPBRGH 21Ch 29Ch CCP2AS 31Ch CCPR5L 39Ch
01Dh 09Dh ADCON0 11Dh APFCON 19Dh RCSTA 21Dh 29Dh PSTR2CON 31Dh CCPR5H 39Dh
01Eh CPSCON0 09Eh ADCON1 11Eh 19Eh TXSTA 21Eh 29Eh CCPTMRS0 31Eh CCP5CON 39Eh
01Fh CPSCON1 09Fh —11Fh 19Fh BAUDCON 21Fh 29Fh CCPTMRS1 31Fh —39Fh
020h
General
Purpose
Register
96 Bytes
0A0h
General
Purpose
Register
80 Bytes
120h
General
Purpose
Register
80 Bytes
1A0h
General
Purpose
Register
80 Bytes
220h
General
Purpose
Register
80 Bytes
2A0h
General
Purpose
Register
80 Bytes
320h General Purpose
Register
16 Bytes
3A0h
Unimplemented
Read as ‘0
32Fh
330h Unimplemented
Read as ‘0
06Fh 0EFh 16Fh 1EFh 26Fh 2EFh 36Fh 3EFh
070h 0F0h
Accesses
70h – 7Fh
170h
Accesses
70h – 7Fh
1F0h
Accesses
70h – 7Fh
270h
Accesses
70h – 7Fh
2F0h
Accesses
70h – 7Fh
370h
Accesses
70h – 7Fh
3F0h
Accesses
70h – 7Fh
07Fh 0FFh 17Fh 1FFh 27Fh 2FFh 37Fh 3FFh
PIC16(L)F1934/6/7
DS41364E-page 34 2008-2011 Microchip Technology Inc.
TABLE 3-6: PIC16(L)F1936/1937 MEMORY MAP, BANKS 8-15
Legend: = Unimplemented data memory locations, read as ‘0’.
BANK 8 BANK 9 BANK 10 BANK 11 BANK 12 BANK 13 BANK 14 BANK 15
400h INDF0 480h INDF0 500h INDF0 580h INDF0 600h INDF0 680h INDF0 700h INDF0 780h INDF0
401h INDF1 481h INDF1 501h INDF1 581h INDF1 601h INDF1 681h INDF1 701h INDF1 781h INDF1
402h PCL 482h PCL 502h PCL 582h PCL 602h PCL 682h PCL 702h PCL 782h PCL
403h STATUS 483h STATUS 503h STATUS 583h STATUS 603h STATUS 683h STATUS 703h STATUS 783h STATUS
404h FSR0L 484h FSR0L 504h FSR0L 584h FSR0L 604h FSR0L 684h FSR0L 704h FSR0L 784h FSR0L
405h FSR0H 485h FSR0H 505h FSR0H 585h FSR0H 605h FSR0H 685h FSR0H 705h FSR0H 785h FSR0H
406h FSR1L 486h FSR1L 506h FSR1L 586h FSR1L 606h FSR1L 686h FSR1L 706h FSR1L 786h FSR1L
407h FSR1H 487h FSR1H 507h FSR1H 587h FSR1H 607h FSR1H 687h FSR1H 707h FSR1H 787h FSR1H
408h BSR 488h BSR 508h BSR 588h BSR 608h BSR 688h BSR 708h BSR 788h BSR
409h WREG 489h WREG 509h WREG 589h WREG 609h WREG 689h WREG 709h WREG 789h WREG
40Ah PCLATH 48Ah PCLATH 50Ah PCLATH 58Ah PCLATH 60Ah PCLATH 68Ah PCLATH 70Ah PCLATH 78Ah PCLATH
40Bh INTCON 48Bh INTCON 50Bh INTCON 58Bh INTCON 60Bh INTCON 68Bh INTCON 70Bh INTCON 78Bh INTCON
40Ch 48Ch 50Ch 58Ch 60Ch 68Ch 70Ch 78Ch
40Dh 48Dh 50Dh 58Dh 60Dh 68Dh 70Dh 78Dh
40Eh 48Eh 50Eh 58Eh 60Eh 68Eh 70Eh 78Eh
40Fh 48Fh 50Fh 58Fh 60Fh 68Fh 70Fh 78Fh
410h 490h 510h 590h 610h 690h 710h 790h
411h 491h 511h 591h 611h 691h 711h 791h
See Ta bl e 3 - 9 or
Tab l e 3 -1 0
412h 492h 512h 592h 612h 692h 712h 792h
413h 493h 513h 593h 613h 693h 713h 793h
414h 494h 514h 594h 614h 694h 714h 794h
415h TMR4 495h 515h 595h 615h 695h 715h 795h
416h PR4 496h 516h 596h 616h 696h 716h 796h
417h T4CON 497h 517h 597h 617h 697h 717h 797h
418h 498h 518h 598h 618h 698h 718h 798h
419h 499h 519h 599h 619h 699h 719h 799h
41Ah 49Ah 51Ah 59Ah 61Ah 69Ah 71Ah 79Ah
41Bh 49Bh 51Bh 59Bh 61Bh 69Bh 71Bh 79Bh
41Ch TMR6 49Ch 51Ch 59Ch 61Ch 69Ch 71Ch 79Ch
41Dh PR6 49Dh 51Dh 59Dh 61Dh 69Dh 71Dh 79Dh
41Eh T6CON 49Eh 51Eh 59Eh 61Eh 69Eh 71Eh 79Eh
41Fh 49Fh 51Fh 59Fh 61Fh 69Fh 71Fh 79Fh
420h
Unimplemented
Read as ‘0
4A0h
Unimplemented
Read as ‘0
520h
Unimplemented
Read as ‘0
5A0h
Unimplemented
Read as ‘0
620h
Unimplemented
Read as ‘0
6A0h
Unimplemented
Read as ‘0
720h
Unimplemented
Read as ‘0
7A0h
46Fh 4EFh 56Fh 5EFh 66Fh 6EFh 76Fh 7EFh
470h
Accesses
70h – 7Fh
4F0h
Accesses
70h – 7Fh
570h
Accesses
70h – 7Fh
5F0h
Accesses
70h – 7Fh
670h
Accesses
70h – 7Fh
6F0h
Accesses
70h – 7Fh
770h
Accesses
70h – 7Fh
7F0h
Accesses
70h – 7Fh
47Fh 4FFh 57Fh 5FFh 67Fh 6FFh 77Fh 7FFh
2008-2011 Microchip Technology Inc. DS41364E-page 35
PIC16(L)F1934/6/7
TABLE 3-7: PIC16(L)F1934/6/7 MEMORY MAP, BANKS 16-23
Legend: = Unimplemented data memory locations, read as ‘0’.
BANK 16 BANK 17 BANK 18 BANK 19 BANK 20 BANK 21 BANK 22 BANK 23
800h INDF0 880h INDF0 900h INDF0 980h INDF0 A00h INDF0 A80h INDF0 B00h INDF0 B80h INDF0
801h INDF1 881h INDF1 901h INDF1 981h INDF1 A01h INDF1 A81h INDF1 B01h INDF1 B81h INDF1
802h PCL 882h PCL 902h PCL 982h PCL A02h PCL A82h PCL B02h PCL B82h PCL
803h STATUS 883h STATUS 903h STATUS 983h STATUS A03h STATUS A83h STATUS B03h STATUS B83h STATUS
804h FSR0L 884h FSR0L 904h FSR0L 984h FSR0L A04h FSR0L A84h FSR0L B04h FSR0L B84h FSR0L
805h FSR0H 885h FSR0H 905h FSR0H 985h FSR0H A05h FSR0H A85h FSR0H B05h FSR0H B85h FSR0H
806h FSR1L 886h FSR1L 906h FSR1L 986h FSR1L A06h FSR1L A86h FSR1L B06h FSR1L B86h FSR1L
807h FSR1H 887h FSR1H 907h FSR1H 987h FSR1H A07h FSR1H A87h FSR1H B07h FSR1H B87h FSR1H
808h BSR 888h BSR 908h BSR 988h BSR A08h BSR A88h BSR B08h BSR B88h BSR
809h WREG 889h WREG 909h WREG 989h WREG A09h WREG A89h WREG B09h WREG B89h WREG
80Ah PCLATH 88Ah PCLATH 90Ah PCLATH 98Ah PCLATH A0Ah PCLATH A8Ah PCLATH B0Ah PCLATH B8Ah PCLATH
80Bh INTCON 88Bh INTCON 90Bh INTCON 98Bh INTCON A0Bh INTCON A8Bh INTCON B0Bh INTCON B8Bh INTCON
80Ch 88Ch 90Ch 98Ch —A0Ch—A8Ch—B0Ch—B8Ch
80Dh 88Dh 90Dh 98Dh —A0Dh—A8Dh—B0Dh—B8Dh
80Eh —88Eh—90Eh—98Eh—A0Eh—A8Eh—B0Eh—B8Eh
80Fh —88Fh—90Fh—98Fh—A0Fh—A8Fh—B0Fh—B8Fh
810h —890h—910h—990h—A10h—A90h—B10h—B90h
811h —891h—911h—991h—A11h—A91h—B11h—B91h
812h —892h—912h—992h—A12h—A92h—B12h—B92h
813h —893h—913h—993h—A13h—A93h—B13h—B93h
814h —894h—914h—994h—A14h—A94h—B14h—B94h
815h —895h—915h—995h—A15h—A95h—B15h—B95h
816h —896h—916h—996h—A16h—A96h—B16h—B96h
817h —897h—917h—997h—A17h—A97h—B17h—B97h
818h —898h—918h—998h—A18h—A98h—B18h—B98h
819h —899h—919h—999h—A19h—A99h—B19h—B99h
81Ah —89Ah—91Ah—99Ah—A1Ah—A9Ah—B1Ah—B9Ah
81Bh —89Bh—91Bh—99Bh—A1Bh—A9Bh—B1Bh—B9Bh
81Ch 89Ch 91Ch 99Ch —A1Ch—A9Ch—B1Ch—B9Ch
81Dh 89Dh 91Dh 99Dh —A1Dh—A9Dh—B1Dh—B9Dh
81Eh —89Eh—91Eh—99Eh—A1Eh—A9Eh—B1Eh—B9Eh
81Fh —89Fh—91Fh—99Fh—A1Fh—A9Fh—B1Fh—B9Fh
820h
Unimplemented
Read as ‘0
8A0h
Unimplemented
Read as ‘0
920h
Unimplemented
Read as ‘0
9A0h
Unimplemented
Read as ‘0
A20h
Unimplemented
Read as ‘0
AA0h
Unimplemented
Read as ‘0
B20h
Unimplemented
Read as ‘0
BA0h
Unimplemented
Read as ‘0
86Fh 8EFh 96Fh 9EFh A6Fh AEFh B6Fh BEFh
870h
Accesses
70h – 7Fh
8F0h
Accesses
70h – 7Fh
970h
Accesses
70h – 7Fh
9F0h
Accesses
70h – 7Fh
A70h
Accesses
70h – 7Fh
AF0h
Accesses
70h – 7Fh
B70h
Accesses
70h – 7Fh
BF0h
Accesses
70h – 7Fh
87Fh 8FFh 97Fh 9FFh A7Fh AFFh B7Fh BFFh
PIC16(L)F1934/6/7
DS41364E-page 36 2008-2011 Microchip Technology Inc.
TABLE 3-8: PIC16(L)F1934/6/7 MEMORY MAP, BANKS 24-31
Legend: = Unimplemented data memory locations, read as ‘0’.
BANK 24 BANK 25 BANK 26 BANK 27 BANK 28 BANK 29 BANK 30 BANK 31
C00h INDF0 C80h INDF0 D00h INDF0 D80h INDF0 E00h INDF0 E80h INDF0 F00h INDF0 F80h INDF0
C01h INDF1 C81h INDF1 D01h INDF1 D81h INDF1 E01h INDF1 E81h INDF1 F01h INDF1 F81h INDF1
C02h PCL C82h PCL D02h PCL D82h PCL E02h PCL E82h PCL F02h PCL F82h PCL
C03h STATUS C83h STATUS D03h STATUS D83h STATUS E03h STATUS E83h STATUS F03h STATUS F83h STATUS
C04h FSR0L C84h FSR0L D04h FSR0L D84h FSR0L E04h FSR0L E84h FSR0L F04h FSR0L F84h FSR0L
C05h FSR0H C85h FSR0H D05h FSR0H D85h FSR0H E05h FSR0H E85h FSR0H F05h FSR0H F85h FSR0H
C06h FSR1L C86h FSR1L D06h FSR1L D86h FSR1L E06h FSR1L E86h FSR1L F06h FSR1L F86h FSR1L
C07h FSR1H C87h FSR1H D07h FSR1H D87h FSR1H E07h FSR1H E87h FSR1H F07h FSR1H F87h FSR1H
C08h BSR C88h BSR D08h BSR D88h BSR E08h BSR E88h BSR F08h BSR F88h BSR
C09h WREG C89h WREG D09h WREG D89h WREG E09h WREG E89h WREG F09h WREG F89h WREG
C0Ah PCLATH C8Ah PCLATH D0Ah PCLATH D8Ah PCLATH E0Ah PCLATH E8Ah PCLATH F0Ah PCLATH F8Ah PCLATH
C0Bh INTCON C8Bh INTCON D0Bh INTCON D8Bh INTCON E0Bh INTCON E8Bh INTCON F0Bh INTCON F8Bh INTCON
C0Ch —C8Ch—D0Ch—D8Ch—E0Ch—E8Ch—F0Ch—F8Ch
See Tabl e 3- 11
C0Dh —C8Dh—D0Dh—D8Dh—E0Dh—E8Dh—F0Dh—F8Dh
C0Eh —C8Eh—D0Eh—D8Eh—E0Eh—E8Eh—F0Eh—F8Eh
C0Fh —C8Fh—D0Fh—D8Fh—E0Fh—E8Fh—F0Fh—F8Fh
C10h —C90h—D10h—D90h—E10h—E90h—F10h—F90h
C11h —C91h—D11h—D91h—E11h—E91h—F11h—F91h
C12h —C92h—D12h—D92h—E12h—E92h—F12h—F92h
C13h —C93h—D13h—D93h—E13h—E93h—F13h—F93h
C14h —C94h—D14h—D94h—E14h—E94h—F14h—F94h
C15h —C95h—D15h—D95h—E15h—E95h—F15h—F95h
C16h —C96h—D16h—D96h—E16h—E96h—F16h—F96h
C17h —C97h—D17h—D97h—E17h—E97h—F17h—F97h
C18h —C98h—D18h—D98h—E18h—E98h—F18h—F98h
C19h —C99h—D19h—D99h—E19h—E99h—F19h—F99h
C1Ah —C9Ah—D1Ah—D9Ah—E1Ah—E9Ah—F1Ah—F9Ah
C1Bh —C9Bh—D1Bh—D9Bh—E1Bh—E9Bh—F1Bh—F9Bh
C1Ch —C9Ch—D1Ch—D9Ch—E1Ch—E9Ch—F1Ch—F9Ch
C1Dh —C9Dh—D1Dh—D9Dh—E1Dh—E9Dh—F1Dh—F9Dh
C1Eh —C9Eh—D1Eh—D9Eh—E1Eh—E9Eh—F1Eh—F9Eh
C1Fh —C9Fh—D1Fh—D9Fh—E1Fh—E9Fh—F1Fh—F9Fh
C20h
Unimplemented
Read as ‘0
CA0h
Unimplemented
Read as ‘0
D20h
Unimplemented
Read as ‘0
DA0h
Unimplemented
Read as ‘0
E20h
Unimplemented
Read as ‘0
EA0h
Unimplemented
Read as ‘0
F20h
Unimplemented
Read as ‘0
FA0h
C6Fh CEFh D6Fh DEFh E6Fh EEFh F6Fh FEFh
C70h
Accesses
70h – 7Fh
CF0h
Accesses
70h – 7Fh
D70h
Accesses
70h – 7Fh
DF0h
Accesses
70h – 7Fh
E70h
Accesses
70h – 7Fh
EF0h
Accesses
70h – 7Fh
F70h
Accesses
70h – 7Fh
FF0h
Accesses
70h – 7Fh
CFFh CFFh D7Fh DFFh E7Fh EFFh F7Fh FFFh
2008-2011 Microchip Technology Inc. DS41364E-page 37
PIC16(L)F1934/6/7
TABLE 3-9: PIC16(L)F1936 MEMORY MAP,
BANK 15 TABLE 3-10: PIC16(L)F1934/7 MEMORY
MAP, BANK 15
Legend: = Unimplemented data memory locations, read
as ‘0’.
Bank 15
791h LCDCON
792h LCDPS
793h LCDREF
794h LCDCST
795h LCDRL
796h
797h
798h LCDSE0
799h LCDSE1
79Ah
79Bh
79Ch
79Dh
79Eh
79Fh
7A0h LCDDATA0
7A1h LCDDATA1
7A2h
7A3h LCDDATA3
7A4h LCDDATA4
7A5h
7A6h LCDDATA6
7A7h LCDDATA7
7A8h
7A9h LCDDATA9
7AAh LCDDATA10
7ABh
7ACh
7ADh
7AEh
7AFh
7B0h
7B1h
7B2h
7B3h
7B4h
7B5h
7B6h
7B7h
7B8h
Unimplemented
Read as ‘0
7EFh
Legend: = Unimplemented data memory locations, read
as ‘0’.
Bank 15
791h LCDCON
792h LCDPS
793h LCDREF
794h LCDCST
795h LCDRL
796h
797h
798h LCDSE0
799h LCDSE1
79Ah LCDSE2
79Bh
79Ch
79Dh
79Eh
79Fh
7A0h LCDDATA0
7A1h LCDDATA1
7A2h LCDDATA2
7A3h LCDDATA3
7A4h LCDDATA4
7A5h LCDDATA5
7A6h LCDDATA6
7A7h LCDDATA7
7A8h LCDDATA8
7A9h LCDDATA9
7AAh LCDDATA10
7ABh LCDDATA11
7ACh
7ADh
7AEh
7AFh
7B0h
7B1h
7B2h
7B3h
7B4h
7B5h
7B6h
7B7h
7B8h
Unimplemented
Read as ‘0
7EFh
PIC16(L)F1934/6/7
DS41364E-page 38 2008-2011 Microchip Technology Inc.
TABLE 3-11: PIC16(L)F1934/6/7 MEMORY
MAP, BANK 31 3.2.6 SPECIAL FUNCTION REGISTERS
SUMMARY
The Special Function Register Summary for the device
family are as follows:
Legend: = Unimplemented data memory locations, read
as ‘0’.
Bank 31
F8Ch
Unimplemented
Read as ‘0
FE3h
FE4h STATUS_SHAD
FE5h WREG_SHAD
FE6h BSR_SHAD
FE7h PCLATH_SHAD
FE8h FSR0L_SHAD
FE9h FSR0H_SHAD
FEAh FSR1L_SHAD
FEBh FSR1H_SHAD
FECh
FEDh STKPTR
FEEh TOSL
FEFh TOSH
Device Bank(s) Page No.
PIC16(L)F1934/6/7
039
140
241
342
443
544
645
746
847
9-14 48
15 49
16-30 51
31 52
2008-2011 Microchip Technology Inc. DS41364E-page 39
PIC16(L)F1934/6/7
=
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Bank 0
000h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
001h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
002h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
003h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
004h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
005h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
006h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
007h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
008h(2) BSR BSR<4:0> ---0 0000 ---0 0000
009h(2) WREG Working Register 0000 0000 uuuu uuuu
00Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
00Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
00Ch PORTA PORTA Data Latch when written: PORTA pins when read xxxx xxxx uuuu uuuu
00Dh PORTB PORTB Data Latch when written: PORTB pins when read xxxx xxxx uuuu uuuu
00Eh PORTC PORTC Data Latch when written: PORTC pins when read xxxx xxxx uuuu uuuu
00Fh(3) PORTD PORTD Data Latch when written: PORTD pins when read xxxx xxxx uuuu uuuu
010h PORTE —RE3RE2
(3) RE1(3) RE0(3) ---- xxxx ---- uuuu
011h PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 0000 0000 0000 0000
012h PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF 0000 00-0 0000 00-0
013h PIR3 CCP5IF CCP4IF CCP3IF TMR6IF —TMR4IF-000 0-0- -000 0-0-
014h Unimplemented
015h TMR0 Timer0 Module Register xxxx xxxx uuuu uuuu
016h TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register xxxx xxxx uuuu uuuu
017h TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register xxxx xxxx uuuu uuuu
018h T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON0000 00-0 uuuu uu-u
019h T1GCON TMR1GE T1GPOL T1GTM T1GSPM T1GGO/
DONE
T1GVAL T1GSS<1:0> 0000 0x00 uuuu uxuu
01Ah TMR2 Timer2 Module Register 0000 0000 0000 0000
01Bh PR2 Timer2 Period Register 1111 1111 1111 1111
01Ch T2CON T2OUTPS<3:0> TMR2ON T2CKPS<1:0> -000 0000 -000 0000
01Dh Unimplemented
01Eh CPSCON0 CPSON CPSRNG1 CPSRNG0 CPSOUT T0XCS 0--- 0000 0--- 0000
01Fh CPSCON1 —CPSCH<3:0>---- 0000 ---- 0000
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 40 2008-2011 Microchip Technology Inc.
Bank 1
080h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
081h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
082h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
083h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
084h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
085h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
086h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
087h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
088h(2) BSR BSR<4:0> ---0 0000 ---0 0000
089h(2) WREG Working Register 0000 0000 uuuu uuuu
08Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
08Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
08Ch TRISA PORTA Data Direction Register 1111 1111 1111 1111
08Dh TRISB PORTB Data Direction Register 1111 1111 1111 1111
08Eh TRISC PORTC Data Direction Register 1111 1111 1111 1111
08Fh(3) TRISD PORTD Data Direction Register 1111 1111 1111 1111
090h TRISE (4) TRISE2(3) TRISE1(3) TRISE0(3) ---- 1111 ---- 1111
091h PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 0000 0000 0000 0000
092h PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 0000 00-0 0000 00-0
093h PIE3 CCP5IE CCP4IE CCP3IE TMR6IE —TMR4IE-000 0-0- -000 0-0-
094h Unimplemented
095h OPTION_R
EG
WPUEN INTEDG TMROCS TMROSE PSA PS<2:0> 1111 1111 1111 1111
096h PCON STKOVF STKUNF —RMCLRRI POR BOR 00-- 11qq qq-- qquu
097h WDTCON WDTPS<4:0> SWDTEN --01 0110 --01 0110
098h OSCTUNE TUN<5:0> --00 0000 --00 0000
099h OSCCON SPLLEN IRCF<3:0> —SCS<1:0>0011 1-00 0011 1-00
09Ah OSCSTAT T1OSCR PLLR OSTS HFIOFR HFIOFL MFIOFR LFIOFR HFIOFS 00q0 0q0- qqqq qq0-
09Bh ADRESL A/D Result Register Low xxxx xxxx uuuu uuuu
09Ch ADRESH A/D Result Register High xxxx xxxx uuuu uuuu
09Dh ADCON0 CHS<4:0>
GO/DONE
ADON -000 0000 -000 0000
09Eh ADCON1 ADFM ADCS<2:0> ADNREF
ADPREF1
ADPREF0 0000 -000 0000 -000
09Fh Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 41
PIC16(L)F1934/6/7
Bank 2
100h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
101h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
102h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
103h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
104h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
105h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
106h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
107h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
108h(2) BSR BSR<4:0> ---0 0000 ---0 0000
109h(2) WREG Working Register 0000 0000 uuuu uuuu
10Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
10Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
10Ch LATA PORTA Data Latch xxxx xxxx uuuu uuuu
10Dh LATB PORTB Data Latch xxxx xxxx uuuu uuuu
10Eh LATC PORTC Data Latch xxxx xxxx uuuu uuuu
10Fh(3) LATD PORTD Data Latch xxxx xxxx uuuu uuuu
110h LATE —LATE2
(3) LATE1(3) LATE0(3) ---- -xxx ---- -uuu
111h CM1CON0 C1ON C1OUT C1OE C1POL C1SP C1HYS C1SYNC 0000 -100 0000 -100
112h CM1CON1 C1INTP C1INTN C1PCH1 C1PCH0 C1NCH<1:0> 0000 --00 0000 --00
113h CM2CON0 C2ON C2OUT C2OE C2POL C2SP C2HYS C2SYNC 0000 -100 0000 -100
114h CM2CON1 C2INTP C2INTN C2PCH1 C2PCH0 C2NCH<1:0> 0000 --00 0000 --00
115h CMOUT MC2OUT MC1OUT ---- --00 ---- --00
116h BORCON SBOREN BORRDY 1--- ---q u--- ---u
117h FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR1 CDAFVR0 ADFVR<1:0> 0q00 0000 0q00 0000
118h DACCON0 DACEN DACLPS DACOE --- DACPSS<1:0> --- DACNSS 000- 00-0 000- 00-0
119h DACCON1 --- --- --- DACR<4:0> ---0 0000 ---0 0000
11Ah SRCON0 SRLEN SRCLK2 SRCLK1 SRCLK0 SRQEN SRNQEN SRPS SRPR 0000 0000 0000 0000
11Bh SRCON1 SRSPE SRSCKE SRSC2E SRSC1E SRRPE SRRCKE SRRC2E SRRC1E 0000 0000 0000 0000
11Ch Unimplemented
11Dh APFCON CCP3SEL T1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL -000 0000 -000 0000
11Eh Unimplemented
11Fh Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 42 2008-2011 Microchip Technology Inc.
Bank 3
180h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
181h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
182h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
183h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
184h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
185h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
186h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
187h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
188h(2) BSR BSR<4:0> ---0 0000 ---0 0000
189h(2) WREG Working Register 0000 0000 uuuu uuuu
18Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
18Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
18Ch ANSELA ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 --11 1111 --11 1111
18Dh ANSELB ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 --11 1111 --11 1111
18Eh Unimplemented
18Fh(3) ANSELD ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0 1111 1111 1111 1111
190h(3) ANSELE ANSE2 ANSE1 ANSE0 ---- -111 ---- -111
191h EEADRL EEPROM / Program Memory Address Register Low Byte 0000 0000 0000 0000
192h EEADRH EEPROM / Program Memory Address Register High Byte -000 0000 -000 0000
193h EEDATL EEPROM / Program Memory Read Data Register Low Byte xxxx xxxx uuuu uuuu
194h EEDATH EEPROM / Program Memory Read Data Register High Byte --xx xxxx --uu uuuu
195h EECON1 EEPGD CFGS LWLO FREE WRERR WREN WR RD 0000 x000 0000 q000
196h EECON2 EEPROM control register 2 0000 0000 0000 0000
197h Unimplemented
198h Unimplemented
199h RCREG USART Receive Data Register 0000 0000 0000 0000
19Ah TXREG USART Transmit Data Register 0000 0000 0000 0000
19Bh SPBRGL BRG<7:0> 0000 0000 0000 0000
19Ch SPBRGH BRG<15:8> 0000 0000 0000 0000
19Dh RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 0000 000x 0000 000x
19Eh TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 0000 0010 0000 0010
19Fh BAUDCON ABDOVF RCIDL SCKP BRG16 WUE ABDEN 01-0 0-00 01-0 0-00
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 43
PIC16(L)F1934/6/7
Bank 4
200h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
201h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
202h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
203h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
204h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
205h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
206h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
207h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
208h(2) BSR BSR<4:0> ---0 0000 ---0 0000
209h(2) WREG Working Register 0000 0000 uuuu uuuu
20Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
20Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
20Ch Unimplemented
20Dh WPUB WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0 1111 1111 1111 1111
20Eh Unimplemented
20Fh Unimplemented
210h WPUE WPUE3 ---- 1--- ---- 1---
211h SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register xxxx xxxx uuuu uuuu
212h SSPADD ADD<7:0> 0000 0000 0000 0000
213h SSPMSK MSK<7:0> 1111 1111 1111 1111
214h SSPSTAT SMP CKE D/A PSR/WUA BF 0000 0000 0000 0000
215h SSPCON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 0000 0000 0000 0000
216h SSPCON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN 0000 0000 0000 0000
217h SSPCON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 0000 0000 0000 0000
218h Unimplemented
219h Unimplemented
21Ah Unimplemented
21Bh Unimplemented
21Ch Unimplemented
21Dh Unimplemented
21Eh Unimplemented
21Fh Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 44 2008-2011 Microchip Technology Inc.
Bank 5
280h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
281h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
282h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
283h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
284h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
285h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
286h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
287h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
288h(2) BSR BSR<4:0> ---0 0000 ---0 0000
289h(2) WREG Working Register 0000 0000 uuuu uuuu
28Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
28Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
28Ch Unimplemented
28Dh Unimplemented
28Eh Unimplemented
28Fh Unimplemented
290h Unimplemented
291h CCPR1L Capture/Compare/PWM Register 1 (LSB) xxxx xxxx uuuu uuuu
292h CCPR1H Capture/Compare/PWM Register 1 (MSB) xxxx xxxx uuuu uuuu
293h CCP1CON P1M<1:0> DC1B<1:0> CCP1M<3:0> 0000 0000 0000 0000
294h PWM1CON P1RSEN P1DC<6:0> 0000 0000 0000 0000
295h CCP1AS CCP1ASE CCP1AS<2:0> PSS1AC<1:0> PSS1BD<1:0> 0000 0000 0000 0000
296h PSTR1CON STR1SYNC STR1D STR1C STR1B STR1A ---0 0001 ---0 0001
297h Unimplemented
298h CCPR2L Capture/Compare/PWM Register 2 (LSB) xxxx xxxx uuuu uuuu
299h CCPR2H Capture/Compare/PWM Register 2 (MSB) xxxx xxxx uuuu uuuu
29Ah CCP2CON P2M<1:0> DC2B<1:0> CCP2M<3:0> 0000 0000 0000 0000
29Bh PWM2CON P2RSEN P2DC<6:0> 0000 0000 0000 0000
29Ch CCP2AS CCP2ASE CCP2AS<2:0> PSS2AC<1:0> PSS2BD<1:0> 0000 0000 0000 0000
29Dh PSTR2CON STR2SYNC STR2D STR2C STR2B STR2A ---0 0001 ---0 0001
29Eh CCPTMRS
0
C4TSEL1 C4TSEL0 C3TSEL1 C3TSEL0 C2TSEL1 C2TSEL0 C1TSEL1 C1TSEL0 0000 0000 0000 0000
29Fh CCPTMRS
1
C5TSEL<1:0> ---- --00 ---- --00
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 45
PIC16(L)F1934/6/7
Bank 6
300h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
301h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
302h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
303h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
304h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
305h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
306h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
307h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
308h(2) BSR BSR<4:0> ---0 0000 ---0 0000
309h(2) WREG Working Register 0000 0000 uuuu uuuu
30Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
30Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
30Ch Unimplemented
30Dh Unimplemented
30Eh Unimplemented
30Fh Unimplemented
310h Unimplemented
311h CCPR3L Capture/Compare/PWM Register 3 (LSB) xxxx xxxx uuuu uuuu
312h CCPR3H Capture/Compare/PWM Register 3 (MSB) xxxx xxxx uuuu uuuu
313h CCP3CON P3M<1:0> DC3B<1:0> CCP3M<1:0> 0000 0000 0000 0000
314h PWM3CON P3RSEN P3DC<6:0> 0000 0000 0000 0000
315h CCP3AS CCP3ASE CCP3AS<2:0> PSS3AC<1:0> PSS3BD<1:0> 0000 0000 0000 0000
316h PSTR3CON STR3SYNC STR3D STR3C STR3B STR3A ---0 0001 ---0 0001
317h Unimplemented
318h CCPR4L Capture/Compare/PWM Register 4 (LSB) xxxx xxxx uuuu uuuu
319h CCPR4H Capture/Compare/PWM Register 4 (MSB) xxxx xxxx uuuu uuuu
31Ah CCP4CON DC4B<1:0> CCP4M<3:0> --00 0000 --00 0000
31Bh Unimplemented
31Ch CCPR5L Capture/Compare/PWM Register 5 (LSB) xxxx xxxx uuuu uuuu
31Dh CCPR5H Capture/Compare/PWM Register 5 (MSB) xxxx xxxx uuuu uuuu
31Eh CCP5CON DC5B<1:0> CCP5M<3:0> --00 0000
--00 0000
31Fh Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 46 2008-2011 Microchip Technology Inc.
Bank 7
380h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
381h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
382h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
383h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
384h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
385h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
386h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
387h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
388h(2) BSR BSR<4:0> ---0 0000 ---0 0000
389h(2) WREG Working Register 0000 0000 uuuu uuuu
38Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
38Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
38Ch Unimplemented
38Dh Unimplemented
38Eh Unimplemented
38Fh Unimplemented
390h Unimplemented
391h Unimplemented
392h Unimplemented
393h Unimplemented
394h IOCBP IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0 0000 0000 0000 0000
395h IOCBN IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0 0000 0000 0000 0000
396h IOCBF IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0 0000 0000 0000 0000
397h Unimplemented
398h Unimplemented
399h Unimplemented
39Ah Unimplemented
39Bh Unimplemented
39Ch Unimplemented
39Dh Unimplemented
39Eh Unimplemented
39Fh Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 47
PIC16(L)F1934/6/7
Bank 8
400h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
401h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
402h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
403h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
404h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
405h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
406h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
407h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
408h(2) BSR BSR<4:0> ---0 0000 ---0 0000
409h(2) WREG Working Register 0000 0000 uuuu uuuu
40Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
40Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
40Ch Unimplemented
40Dh Unimplemented
40Eh Unimplemented
40Fh Unimplemented
410h Unimplemented
411h Unimplemented
412h Unimplemented
413h Unimplemented
414h Unimplemented
415h TMR4 Timer4 Module Register 0000 0000 0000 0000
416h PR4 Timer4 Period Register 1111 1111 1111 1111
417h T4CON T4OUTPS<3:0> TMR4ON T4CKPS<1:0> -000 0000 -000 0000
418h Unimplemented
419h Unimplemented
41Ah Unimplemented
41Bh Unimplemented
41Ch TMR6 Timer6 Module Register 0000 0000 0000 0000
41Dh PR6 Timer6 Period Register 1111 1111 1111 1111
41Eh T6CON T6OUTPS<3:0> TMR6ON T6CKPS<1:0> -000 0000 -000 0000
41Fh Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 48 2008-2011 Microchip Technology Inc.
Banks 9-14
x00h/
x80h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
x00h/
x81h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
x02h/
x82h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
x03h/
x83h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
x04h/
x84h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
x05h/
x85h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
x06h/
x86h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
x07h/
x87h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
x08h/
x88h(2) BSR BSR<4:0> ---0 0000 ---0 0000
x09h/
x89h(2) WREG Working Register 0000 0000 uuuu uuuu
x0Ah/
x8Ah(1),(2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
x0Bh/
x8Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
x0Ch/
x8Ch
x1Fh/
x9Fh
Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 49
PIC16(L)F1934/6/7
Bank 15
780h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
781h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
782h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
783h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
784h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
785h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
786h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
787h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
788h(2) BSR BSR<4:0> ---0 0000 ---0 0000
789h(2) WREG Working Register 0000 0000 uuuu uuuu
78Ah(1, 2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
78Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
78Ch Unimplemented
78Dh Unimplemented
78Eh Unimplemented
78Fh Unimplemented
790h Unimplemented
791h LCDCON LCDEN SLPEN WERR —CS<1:0> LMUX<1:0> 000- 0011 000- 0011
792h LCDPS WFT BIASMD LCDA WA LP<3:0> 0000 0000 0000 0000
793h LCDREF LCDIRE LCDIRS LCDIRI VLCD3PE VLCD2PE VLCD1PE 000- 000- 000- 000-
794h LCDCST LCDCST<2:0> ---- -000 ---- -000
795h LCDRL LRLAP<1:0> LRLBP<1:0> —LRLAT<2:0> 0000 -000 0000 -000
796h Unimplemented
797h Unimplemented
798h LCDSE0 SE<7:0> 0000 0000 uuuu uuuu
799h LCDSE1 SE<15:8> 0000 0000 uuuu uuuu
79Ah LCDSE2(3) SE<23:16> 0000 0000 uuuu uuuu
79Bh Unimplemented
79Ch Unimplemented
79Dh Unimplemented
79Eh Unimplemented
79Fh Unimplemented
7A0h LCDDATA0 SEG7
COM0
SEG6
COM0
SEG5
COM0
SEG4
COM0
SEG3
COM0
SEG2
COM0
SEG1
COM0
SEG0
COM0 xxxx xxxx uuuu uuuu
7A1h LCDDATA1 SEG15
COM0
SEG14
COM0
SEG13
COM0
SEG12
COM0
SEG11
COM0
SEG10
COM0
SEG9
COM0
SEG8
COM0 xxxx xxxx uuuu uuuu
7A2h
LCDDATA2
(
3)
SEG23
COM0
SEG22
COM0
SEG21
COM0
SEG20
COM0
SEG19
COM0
SEG18
COM0
SEG17
COM0
SEG16
COM0 xxxx xxxx uuuu uuuu
7A3h LCDDATA3 SEG7
COM1
SEG6
COM1
SEG5
COM1
SEG4
COM1
SEG3
COM1
SEG2
COM1
SEG1
COM1
SEG0
COM1 xxxx xxxx uuuu uuuu
7A4h LCDDATA4 SEG15
COM1
SEG14
COM1
SEG13
COM1
SEG12
COM1
SEG11
COM1
SEG10
COM1
SEG9
COM1
SEG8
COM1 xxxx xxxx uuuu uuuu
7A5h
LCDDATA5
(
3)
SEG23
COM1
SEG22
COM1
SEG21
COM1
SEG20
COM1
SEG19
COM1
SEG18
COM1
SEG17
COM1
SEG16
COM1 xxxx xxxx uuuu uuuu
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 50 2008-2011 Microchip Technology Inc.
Bank 15 (Continued)
7A6h LCDDATA6 SEG7
COM2
SEG6
COM2
SEG5
COM2
SEG4
COM2
SEG3
COM2
SEG2
COM2
SEG1
COM2
SEG0
COM2 xxxx xxxx uuuu uuuu
7A7h LCDDATA7 SEG15
COM2
SEG14
COM2
SEG13
COM2
SEG12
COM2
SEG11
COM2
SEG10
COM2
SEG9
COM2
SEG8
COM2 xxxx xxxx uuuu uuuu
7A8h
LCDDATA8
(
3)
SEG23
COM2
SEG22
COM2
SEG21
COM2
SEG20
COM2
SEG19
COM2
SEG18
COM2
SEG17
COM2
SEG16
COM2 xxxx xxxx uuuu uuuu
7A9h LCDDATA9 SEG7
COM3
SEG6
COM3
SEG5
COM3
SEG4
COM3
SEG3
COM3
SEG2
COM3
SEG1
COM3
SEG0
COM3 xxxx xxxx uuuu uuuu
7AAh LCDDATA1
0
SEG15
COM3
SEG14
COM3
SEG13
COM3
SEG12
COM3
SEG11
COM3
SEG10
COM3
SEG9
COM3
SEG8
COM3 xxxx xxxx uuuu uuuu
7ABh
LCDDATA11
(
3)
SEG23
COM3
SEG22
COM3
SEG21
COM3
SEG20
COM3
SEG19
COM3
SEG18
COM3
SEG17
COM3
SEG16
COM3 xxxx xxxx uuuu uuuu
7ACh
7EFh
Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 51
PIC16(L)F1934/6/7
Banks 16-30
x00h/
x80h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
x00h/
x81h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
x02h/
x82h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
x03h/
x83h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
x04h/
x84h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
x05h/
x85h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
x06h/
x86h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
x07h/
x87h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
x08h/
x88h(2) BSR BSR<4:0> ---0 0000 ---0 0000
x09h/
x89h(2) WREG Working Register 0000 0000 uuuu uuuu
x0Ah/
x8Ah(1),(2) PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
x0Bh/
x8Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
x0Ch/
x8Ch
x1Fh/
x9Fh
Unimplemented
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 52 2008-2011 Microchip Technology Inc.
Bank 31
F80h(2) INDF0 Addressing this location uses contents of FSR0H/FSR0L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
F81h(2) INDF1 Addressing this location uses contents of FSR1H/FSR1L to address data memory
(not a physical register) xxxx xxxx xxxx xxxx
F82h(2) PCL Program Counter (PC) Least Significant Byte 0000 0000 0000 0000
F83h(2) STATUS —TOPD ZDCC---1 1000 ---q quuu
F84h(2) FSR0L Indirect Data Memory Address 0 Low Pointer 0000 0000 uuuu uuuu
F85h(2) FSR0H Indirect Data Memory Address 0 High Pointer 0000 0000 0000 0000
F86h(2) FSR1L Indirect Data Memory Address 1 Low Pointer 0000 0000 uuuu uuuu
F87h(2) FSR1H Indirect Data Memory Address 1 High Pointer 0000 0000 0000 0000
F88h(2) BSR BSR<4:0> ---0 0000 ---0 0000
F89h(2) WREG Working Register 0000 0000 uuuu uuuu
F8Ah(1),(2
)PCLATH Write Buffer for the upper 7 bits of the Program Counter -000 0000 -000 0000
F8Bh(2) INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 0000 0000 0000 0000
F8Ch
FE3h
Unimplemented
FE4h STATUS_
SHAD
Z_SHAD DC_SHAD C_SHAD ---- -xxx ---- -uuu
FE5h WREG_
SHAD
Working Register Normal (Non-ICD) Shadow xxxx xxxx uuuu uuuu
FE6h BSR_
SHAD
Bank Select Register Normal (Non-ICD) Shadow ---x xxxx ---u uuuu
FE7h PCLATH_
SHAD
Program Counter Latch High Register Normal (Non-ICD) Shadow -xxx xxxx uuuu uuuu
FE8h FSR0L_
SHAD
Indirect Data Memory Address 0 Low Pointer Normal (Non-ICD) Shadow xxxx xxxx uuuu uuuu
FE9h FSR0H_
SHAD
Indirect Data Memory Address 0 High Pointer Normal (Non-ICD) Shadow xxxx xxxx uuuu uuuu
FEAh FSR1L_
SHAD
Indirect Data Memory Address 1 Low Pointer Normal (Non-ICD) Shadow xxxx xxxx uuuu uuuu
FEBh FSR1H_
SHAD
Indirect Data Memory Address 1 High Pointer Normal (Non-ICD) Shadow xxxx xxxx uuuu uuuu
FECh Unimplemented
FEDh STKPTR Current Stack pointer ---1 1111 ---1 1111
FEEh TOSL Top of Stack Low byte xxxx xxxx uuuu uuuu
FEFh TOSH Top of Stack High byte -xxx xxxx -uuu uuuu
TABLE 3-12: SPECIAL FUNCTION REGISTER SUMMARY (CONTINUED)
Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on
POR, BOR
Value on all
other
Resets
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as 0’, r = reserved.
Shaded locations are unimplemented, read as ‘0’.
Note 1: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for the PC<14:8>, whose contents are transferred
to the upper byte of the program counter.
2: These registers can be addressed from any bank.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
4: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 53
PIC16(L)F1934/6/7
3.3 PCL and PCLATH
The Program Counter (PC) is 15 bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<14:8>) is not directly
readable or writable and comes from PCLATH. On any
Reset, the PC is cleared. Figure 3-4 shows the five
situations for the loading of the PC.
FIGURE 3-4: LOADING OF PC IN
DIFFERENT SITUATIONS
3.3.1 MODIFYING PCL
Executing any instruction with the PCL register as the
destination simultaneously causes the Program Coun-
ter PC<14:8> bits (PCH) to be replaced by the contents
of the PCLATH register. This allows the entire contents
of the program counter to be changed by writing the
desired upper 7 bits to the PCLATH register. When the
lower 8 bits are written to the PCL register, all 15 bits of
the program counter will change to the values con-
tained in the PCLATH register and those being written
to the PCL register.
3.3.2 COMPUTED GOTO
A computed GOTO is accomplished by adding an offset to
the program counter (ADDWF PCL). When performing a
table read using a computed GOTO method, care should
be exercised if the table location crosses a PCL memory
boundary (each 256-byte block). Refer to Application
Note AN556, “Implementing a Table Read” (DS00556).
3.3.3 COMPUTED FUNCTION CALLS
A computed function CALL allows programs to maintain
tables of functions and provide another way to execute
state machines or look-up tables. When performing a
table read using a computed function CALL, care
should be exercised if the table location crosses a PCL
memory boundary (each 256-byte block).
If using the CALL instruction, the PCH<2:0> and PCL
registers are loaded with the operand of the CALL
instruction. PCH<6:3> is loaded with PCLATH<6:3>.
The CALLW instruction enables computed calls by com-
bining PCLATH and W to form the destination address.
A computed CALLW is accomplished by loading the W
register with the desired address and executing CALLW.
The PCL register is loaded with the value of W and
PCH is loaded with PCLATH.
3.3.4 BRANCHING
The branching instructions add an offset to the PC.
This allows relocatable code and code that crosses
page boundaries. There are two forms of branching,
BRW and BRA. The PC will have incremented to fetch
the next instruction in both cases. When using either
branching instruction, a PCL memory boundary may be
crossed.
If using BRW, load the W register with the desired
unsigned address and execute BRW. The entire PC will
be loaded with the address PC + 1 + W.
If using BRA, the entire PC will be loaded with PC + 1 +,
the signed value of the operand of the BRA instruction.
PCLPCH 0
14
PC
06 7
ALU Result
8
PCLATH
PCLPCH 0
14
PC
06 4
OPCODE <10:0>
11
PCLATH
PCLPCH 0
14
PC
06 7
W
8
PCLATH
Instruction with
PCL as
Destination
GOTO, CALL
CALLW
PCL
PCH 0
14
PC
PC + W
15
BRW
PCLPCH 0
14
PC
PC + OPCODE <8:0>
15
BRA
PIC16(L)F1934/6/7
DS41364E-page 54 2008-2011 Microchip Technology Inc.
3.4 Stack
All devices have a 16-level x 15-bit wide hardware
stack (refer to Figure 3-1 and Figure 3-2). The stack
space is not part of either program or data space. The
PC is PUSHed onto the stack when CALL or CALLW
instructions are executed or an interrupt causes a
branch. The stack is POPed in the event of a RETURN,
RETLW or a RETFIE instruction execution. PCLATH is
not affected by a PUSH or POP operation.
The stack operates as a circular buffer if the STVREN
bit is programmed to ‘0‘ (Configuration Word 2). This
means that after the stack has been PUSHed sixteen
times, the seventeenth PUSH overwrites the value that
was stored from the first PUSH. The eighteenth PUSH
overwrites the second PUSH (and so on). The
STKOVF and STKUNF flag bits will be set on an Over-
flow/Underflow, regardless of whether the Reset is
enabled.
3.4.1 ACCESSING THE STACK
The stack is available through the TOSH, TOSL and
STKPTR registers. STKPTR is the current value of the
Stack Pointer. TOSH:TOSL register pair points to the
TOP of the stack. Both registers are read/writable. TOS
is split into TOSH and TOSL due to the 15-bit size of the
PC. To access the stack, adjust the value of STKPTR,
which will position TOSH:TOSL, then read/write to
TOSH:TOSL. STKPTR is 5 bits to allow detection of
overflow and underflow.
During normal program operation, CALL, CALLW and
Interrupts will increment STKPTR while RETLW,
RETURN, and RETFIE will decrement STKPTR. At any
time STKPTR can be inspected to see how much stack
is left. The STKPTR always points at the currently used
place on the stack. Therefore, a CALL or CALLW will
increment the STKPTR and then write the PC, and a
return will unload the PC and then decrement the
STKPTR.
Reference Figure 3-5 through Figure 3-8 for examples
of accessing the stack.
FIGURE 3-5: ACCESSING THE STACK EXAMPLE 1
Note 1: There are no instructions/mnemonics
called PUSH or POP. These are actions
that occur from the execution of the
CALL, CALLW, RETURN, RETLW and
RETFIE instructions or the vectoring to
an interrupt address.
Note: Care should be taken when modifying the
STKPTR while interrupts are enabled.
0x0F
0x0E
0x0D
0x0C
0x0B
0x0A
0x09
0x08
0x07
0x06
0x05
0x04
0x03
0x02
0x01
0x00
0x0000
STKPTR = 0x1F
Initial Stack Configuration:
After Reset, the stack is empty. The
empty stack is initialized so the Stack
Pointer is pointing at 0x1F. If the Stack
Overflow/Underflow Reset is enabled, the
TOSH/TOSL registers will return ‘0’. If
the Stack Overflow/Underflow Reset is
disabled, the TOSH/TOSL registers will
return the contents of stack address 0x0F.
0x1F STKPTR = 0x1F
Stack Reset Disabled
(STVREN = 0)
Stack Reset Enabled
(STVREN = 1)
TOSH:TOSL
TOSH:TOSL
2008-2011 Microchip Technology Inc. DS41364E-page 55
PIC16(L)F1934/6/7
FIGURE 3-6: ACCESSING THE STACK EXAMPLE 2
FIGURE 3-7: ACCESSING THE STACK EXAMPLE 3
0x0F
0x0E
0x0D
0x0C
0x0B
0x0A
0x09
0x08
0x07
Return Address0x06
Return Address0x05
Return Address0x04
Return Address0x03
Return Address0x02
Return Address0x01
Return Address0x00
STKPTR = 0x06
After seven CALLs or six CALLs and an
interrupt, the stack looks like the figure
on the left. A series of RETURN instructions
will repeatedly place the return addresses
into the Program Counter and pop the stack.
TOSH:TOSL
PIC16(L)F1934/6/7
DS41364E-page 56 2008-2011 Microchip Technology Inc.
FIGURE 3-8: ACCESSING THE STACK EXAMPLE 4
3.4.2 OVERFLOW/UNDERFLOW RESET
If the STVREN bit in Configuration Word 2 is
programmed to ‘1’, the device will be reset if the stack
is PUSHed beyond the sixteenth level or POPed
beyond the first level, setting the appropriate bits
(STKOVF or STKUNF, respectively) in the PCON
register.
3.5 Indirect Addressing
The INDFn registers are not physical registers. Any
instruction that accesses an INDFn register actually
accesses the register at the address specified by the
File Select Registers (FSR). If the FSRn address
specifies one of the two INDFn registers, the read will
return ‘0’ and the write will not occur (though Status bits
may be affected). The FSRn register value is created
by the pair FSRnH and FSRnL.
The FSR registers form a 16-bit address that allows an
addressing space with 65536 locations. These locations
are divided into three memory regions:
Traditional Data Memory
Linear Data Memory
Program Flash Memory
0x0F
0x0E
0x0D
0x0C
0x0B
0x0A
0x09
0x08
0x07
0x06
0x05
0x04
0x03
0x02
0x01
Return Address0x00 STKPTR = 0x10
When the stack is full, the next CALL or
an interrupt will set the Stack Pointer to
0x10. This is identical to address 0x00
so the stack will wrap and overwrite the
return address at 0x00. If the Stack
Overflow/Underflow Reset is enabled, a
Reset will occur and location 0x00 will
not be overwritten.
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
Return Address
TOSH:TOSL
2008-2011 Microchip Technology Inc. DS41364E-page 57
PIC16(L)F1934/6/7
FIGURE 3-9: INDIR ECT ADDRESSI NG
0x0000
0x0FFF
Traditional
FSR
Address
Range
Data Memory
0x1000 Reserved
Linear
Data Memory
Reserved
0x2000
0x29AF
0x29B0
0x7FFF
0x8000
0xFFFF
0x0000
0x0FFF
0x0000
0x7FFF
Program
Flash Memory
Note: Not all memory regions are completely implemented. Consult device memory tables for memory limits.
0x1FFF
PIC16(L)F1934/6/7
DS41364E-page 58 2008-2011 Microchip Technology Inc.
3.5.1 TRADITIONAL DATA MEMORY
The traditional data memory is a region from FSR
address 0x000 to FSR address 0xFFF. The addresses
correspond to the absolute addresses of all SFR, GPR
and common registers.
FIGURE 3-10: TRADITIONAL DATA MEMORY MAP
Indirect AddressingDirect Addressing
Bank Select Location Select
4 BSR 6 0
From Opcode FSRxL70
Bank Select Location Select
0000 0001 0010 1111
0x00
0x7F
Bank 0 Bank 1 Bank 2 Bank 31
0FSRxH70
0000
2008-2011 Microchip Technology Inc. DS41364E-page 59
PIC16(L)F1934/6/7
3.5.2 LINEAR DATA MEMORY
The linear data memory is the region from FSR
address 0x2000 to FSR address 0x29AF. This region is
a virtual region that points back to the 80-byte blocks of
GPR memory in all the banks.
Unimplemented memory reads as 0x00. Use of the
linear data memory region allows buffers to be larger
than 80 bytes because incrementing the FSR beyond
one bank will go directly to the GPR memory of the next
bank.
The 16 bytes of common memory are not included in
the linear data memory region.
FIGURE 3-11: LINEAR DATA MEMORY
MAP
3.5.3 PROGRAM FLASH MEMORY
To make constant data access easier, the entire
program Flash memory is mapped to the upper half of
the FSR address space. When the MSB of FSRnH is
set, the lower 15 bits are the address in program
memory which will be accessed through INDF. Only the
lower 8 bits of each memory location is accessible via
INDF. Writing to the program Flash memory cannot be
accomplished via the FSR/INDF interface. All
instructions that access program Flash memory via the
FSR/INDF interface will require one additional
instruction cycle to complete.
FIGURE 3-12: PROGRAM FLASH
MEMORY MAP
7
01
7
00
Location Select 0x2000
FSRnH FSRnL
0x020
Bank 0
0x06F
0x0A0
Bank 1
0x0EF
0x120
Bank 2
0x16F
0xF20
Bank 30
0xF6F
0x29AF
0
7
1
7
00
Location Select 0x8000
FSRnH FSRnL
0x0000
0x7FFF
0xFFFF
Program
Flash
Memory
(low 8
bits)
PIC16(L)F1934/6/7
DS41364E-page 60 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 61
PIC16(L)F1934/6/7
4.0 DEVICE CONFIGURATION
Device Configuration consists of Configuration Word 1
and Configuration Word 2, Code Protection and Device
ID.
4.1 Configuration Words
There are several Configuration Word bits that allow
different oscillator and memory protection options.
These are implemented as Configuration Word 1 at
8007h and Configuration Word 2 at 8008h.
Note: The DEBUG bit in Configuration Word 2 is
managed automatically by device
development tools including debuggers
and programmers. For normal device
operation, this bit should be maintained as
a ‘1’.
PIC16(L)F1934/6/7
DS41364E-page 62 2008-2011 Microchip Technology Inc.
REGISTER 4-1: CONFIGURATION WORD 1
R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1
FCMEN IESO CLKOUTEN BOREN1 BOREN0 CPD CP
bit 13 bit 7
R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1 R/P-1/1
MCLRE PWRTE WDTE1 WDTE0 FOSC2 FOSC1 FOSC0
bit 6 bit 0
Legend:
R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set -n = Value when blank or after Bulk Erase
bit 13 FCMEN: Fail-Safe Clock Monitor Enable bit
1 = Fail-Safe Clock Monitor is enabled
0 = Fail-Safe Clock Monitor is disabled
bit 12 IESO: Internal External Switchover bit
1 = Internal/External Switchover mode is enabled
0 = Internal/External Switchover mode is disabled
bit 11 CLKOUTEN: Clock Out Enable bit
1 = CLKOUT function is disabled. I/O or oscillator function on RA6/CLKOUT
0 = CLKOUT function is enabled on RA6/CLKOUT
bit 10-9 BOREN<1:0>: Brown-out Reset Enable bits(1)
11 = BOR enabled
10 = BOR enabled during operation and disabled in Sleep
01 = BOR controlled by SBOREN bit of the PCON register
00 = BOR disabled
bit 8 CPD: Data Code Protection bit(2)
1 = Data memory code protection is disabled
0 = Data memory code protection is enabled
bit 7 CP: Code Protection bit(3)
1 = Program memory code protection is disabled
0 = Program memory code protection is enabled
bit 6 MCLRE: RE3/MCLR/VPP Pin Function Select bit
If LVP bit = 1:
This bit is ignored.
If LVP bit = 0:
1 =RE3/MCLR
/VPP pin function is MCLR; Weak pull-up enabled.
0 = RE3/MCLR/VPP pin function is digital input; MCLR internally disabled; Weak pull-up under control of WPUE3
bit..
bit 5 PWRTE: Power-up Timer Enable bit(1)
1 = PWRT disabled
0 = PWRT enabled
bit 4-3 WDTE<1:0>: Watchdog Timer Enable bit
11 = WDT enabled
10 = WDT enabled while running and disabled in Sleep
01 = WDT controlled by the SWDTEN bit in the WDTCON register
00 = WDT disabled
Note 1: Enabling Brown-out Reset does not automatically enable Power-up Timer.
2: The entire data EEPROM will be erased when the code protection is turned off during an erase.
3: The entire program memory will be erased when the code protection is turned off.
2008-2011 Microchip Technology Inc. DS41364E-page 63
PIC16(L)F1934/6/7
bit 2-0 FOSC<2:0>: Oscillator Selection bits
111 = ECH: External Clock, High-Power mode: CLKIN on RA7/OSC1/CLKIN
110 = ECM: External Clock, Medium-Power mode: CLKIN on RA7/OSC1/CLKIN
101 = ECL: External Clock, Low-Power mode: CLKIN on RA7/OSC1/CLKIN
100 = INTOSC oscillator: I/O function on RA7/OSC1/CLKIN
011 = EXTRC oscillator: RC function on RA7/OSC1/CLKIN
010 = HS oscillator: High-speed crystal/resonator on RA6/OSC2/CLKOUT pin and RA7/OSC1/CLKIN
001 = XT oscillator: Crystal/resonator on RA6/OSC2/CLKOUT pin and RA7/OSC1/CLKIN
000 = LP oscillator: Low-power crystal on RA6/OSC2/CLKOUT pin and RA7/OSC1/CLKIN
REGISTER 4-1: CONFIGURATION WORD 1 (CONTINUED)
Note 1: Enabling Brown-out Reset does not automatically enable Power-up Timer.
2: The entire data EEPROM will be erased when the code protection is turned off during an erase.
3: The entire program memory will be erased when the code protection is turned off.
PIC16(L)F1934/6/7
DS41364E-page 64 2008-2011 Microchip Technology Inc.
REGISTER 4-2: CONFIGURATION WORD 2
R/P-1/1 R/P-1/1 U-1 R/P-1/1 R/P-1/1 R/P-1/1 U-1
LVP(1) DEBUG(3) —BORVSTVRENPLLEN
bit 13 bit 7
U-1 R/P-1/1 R/P-1/1 U-1 U-1 R/P-1/1 R/P-1/1
VCAPEN<1:0>(2) —WRT1WRT0
bit 6 bit 0
Legend:
R = Readable bit P = Programmable bit U = Unimplemented bit, read as ‘1’
‘0’ = Bit is cleared ‘1’ = Bit is set -n = Value when blank or after Bulk Erase
bit 13 LVP: Low-Voltage Programming Enable bit(1)
1 = Low-voltage programming enabled
0 = High-voltage on MCLR/VPP must be used for programming
bit 12 DEBUG: In-Circuit Debugger Mode bit(3)
1 = In-Circuit Debugger disabled, RB6/ICSPCLK and RB7/ICSPDAT are general purpose I/O pins
0 = In-Circuit Debugger enabled, RB6/ICSPCLK and RB7/ICSPDAT are dedicated to the debugger
bit 11 Unimplemented: Read as ‘1
bit 10 BORV: Brown-out Reset Voltage Selection bit
1 = Brown-out Reset voltage set to 1.9V
0 = Brown-out Reset voltage set to 2.5V
bit 9 STVREN: Stack Overflow/Underflow Reset Enable bit
1 = Stack Overflow or Underflow will cause a Reset
0 = Stack Overflow or Underflow will not cause a Reset
bit 8 PLLEN: PLL Enable bit
1 = 4xPLL enabled
0 = 4xPLL disabled
bit 7-6 Unimplemented: Read as ‘1
bit 5-4 VCAPEN<1:0>: Voltage Regulator Capacitor Enable bits(2)
00 =VCAP functionality is enabled on RA0
01 =V
CAP functionality is enabled on RA5
10 =V
CAP functionality is enabled on RA6
11 = No capacitor on VCAP pin
bit 3-2 Unimplemented: Read as ‘1
bit 1-0 WRT<1:0>: Flash Memory Self-Write Protection bits
4 kW Flash memory PIC16(L)F1934 only):
11 = Write protection off
10 = 000h to 1FFh write-protected, 200h to FFFh may be modified by EECON control
01 = 000h to 7FFh write-protected, 800h to FFFh may be modified by EECON control
00 = 000h to FFFh write-protected, no addresses may be modified by EECON control
8 kW Flash memory (PIC16(L)F1936 and PIC16(L)F1937 only):
11 = Write protection off
10 = 000h to 1FFh write-protected, 200h to 1FFFh may be modified by EECON control
01 = 000h to FFFh write-protected, 1000h to 1FFFh may be modified by EECON control
00 = 000h to 1FFFh write-protected, no addresses may be modified by EECON control
Note 1: The LVP bit cannot be programmed to ‘0’ when Programming mode is entered via LVP.
2: Reads as ‘11’ on PIC16LF193X only.
3: The DEBUG bit in Configuration Word is managed automatically by device development tools including
debuggers and programmers. For normal device operation, this bit should be maintained as a ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 65
PIC16(L)F1934/6/7
4.2 Code Protection
Code protection allows the device to be protected from
unauthorized access. Program memory protection and
data EEPROM protection are controlled independently.
Internal access to the program memory and data
EEPROM are unaffected by any code protection
setting.
4.2.1 PROGRAM MEMORY PROTECTION
The entire program memory space is protected from
external reads and writes by the CP bit in Configuration
Word 1. When CP = 0, external reads and writes of
program memory are inhibited and a read will return all
0s. The CPU can continue to read program memory,
regardless of the protection bit settings. Writing the
program memory is dependent upon the write
protection setting. See Section 4.3 “Write
Protection” for more information.
4.2.2 DATA EEPROM PROTECTION
The entire data EEPROM is protected from external
reads and writes by the CPD bit. When CPD = 0,
external reads and writes of data EEPROM are
inhibited. The CPU can continue to read and write data
EEPROM regardless of the protection bit settings.
4.3 Write Protection
Write protection allows the device to be protected from
unintended self-writes. Applications, such as
bootloader software, can be protected while allowing
other regions of the program memory to be modified.
The WRT<1:0> bits in Configuration Word 2 define the
size of the program memory block that is protected.
4.4 User ID
Four memory locations (8000h-8003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
readable and writable during normal execution. See
Section 4.5 “Device ID and Revision ID” for more
information on accessing these memory locations. For
more information on checksum calculation, see the
PIC16F193X/LF193X/PIC16F194X/LF194X/PIC16LF
190X Mem ory Programmin g Specificati on” (DS41397).
PIC16(L)F1934/6/7
DS41364E-page 66 2008-2011 Microchip Technology Inc.
4.5 Device ID and Revision ID
The memory location 8006h is where the Device ID and
Revision ID are stored. The upper nine bits hold the
Device ID. The lower five bits hold the Revision ID. See
Section 11.5 “User ID, Device ID and Configuration
Word Access” for more information on accessing
these memory locations.
Development tools, such as device programmers and
debuggers, may be used to read the Device ID and
Revision ID.
REGISTER 4-3: DEVICEID: DEVICE ID REGISTER(1)
RRRRRRR
DEV8 DEV7 DEV6 DEV5 DEV4 DEV3 DEV2
bit 13 bit 7
RRRRRRR
DEV1 DEV0 REV4 REV3 REV2 REV1 REV0
bit 6 bit 0
Legend: U = Unimplemented bit, read as ‘0’
R = Readable bit W = Writable bit ‘0’ = Bit is cleared
-n = Value at POR ‘1’ = Bit is set x = Bit is unknown
bit 13-5 DEV<8:0>: Device ID bits
100011010 = PIC16F1934
100011011 = PIC16F1936
100011100 = PIC16F1937
100100010 = PIC16LF1934
100100011 = PIC16LF1936
100100100 = PIC16LF1937
bit 4-0 REV<4:0>: Revision ID bits
These bits are used to identify the revision.
Note 1: This location cannot be written.
2008-2011 Microchip Technology Inc. DS41364E-page 67
PIC16(L)F1934/6/7
5.0 OSCILLATOR MODULE (WITH
FAIL-SAFE CLOCK MONITOR)
5.1 Overview
The oscillator module has a wide variety of clock
sources and selection features that allow it to be used
in a wide range of applications while maximizing perfor-
mance and minimizing power consumption. Figure 5-1
illustrates a block diagram of the oscillator module.
Clock sources can be supplied from external oscillators,
quartz crystal resonators, ceramic resonators and
Resistor-Capacitor (RC) circuits. In addition, the system
clock source can be supplied from one of two internal
oscillators and PLL circuits, with a choice of speeds
selectable via software. Additional clock features
include:
Selectable system clock source between external
or internal sources via software.
Two-Speed Start-up mode, which minimizes
latency between external oscillator start-up and
code execution.
Fail-Safe Clock Monitor (FSCM) designed to
detect a failure of the external clock source (LP,
XT, HS, EC or RC modes) and switch
automatically to the internal oscillator.
Oscillator Start-up Timer (OST) ensures stability
of crystal oscillator sources
The oscillator module can be configured in one of eight
clock modes.
1. ECL – External Clock Low-Power mode
(0 MHz to 0.5 MHz)
2. ECM – External Clock Medium-Power mode
(0.5 MHz to 4 MHz)
3. ECH – External Clock High-Power mode
(4 MHz to 32 MHz)
4. LP – 32 kHz Low-Power Crystal mode.
5. XT – Medium Gain Crystal or Ceramic Resonator
Oscillator mode (up to 4 MHz)
6. HS – High Gain Crystal or Ceramic Resonator
mode (4 MHz to 20 MHz)
7. RC – External Resistor-Capacitor (RC).
8. INTOSC – Internal oscillator (31 kHz to 32 MHz).
Clock Source modes are selected by the FOSC<2:0>
bits in the Configuration Word 1. The FOSC bits
determine the type of oscillator that will be used when
the device is first powered.
The EC clock mode relies on an external logic level
signal as the device clock source. The LP, XT, and HS
clock modes require an external crystal or resonator to
be connected to the device. Each mode is optimized for
a different frequency range. The RC clock mode
requires an external resistor and capacitor to set the
oscillator frequency.
The INTOSC internal oscillator block produces low,
medium, and high frequency clock sources, designated
LFINTOSC, MFINTOSC, and HFINTOSC. (see
Internal Oscillator Block, Figure 5-1). A wide selection
of device clock frequencies may be derived from these
three clock sources.
PIC16(L)F1934/6/7
DS41364E-page 68 2008-2011 Microchip Technology Inc.
FIGURE 5-1: SIMPLIFIED PIC® MCU CLOCK SOURCE BLOCK DIAGRAM
4 x PLL
FOSC<2:0>
Oscillator
T1OSCEN
Enable
Oscillator
T1OSO
T1OSI
Clock Source Option
for other modules
OSC1
OSC2
Sleep
LP, XT, HS, RC, EC
T1OSC CPU and
Postscaler
MUX
MUX
16 MHz
8 MHz
4 MHz
2 MHz
1 MHz
250 kHz
500 kHz
IRCF<3:0>
31 kHz
500 kHz
Source
Internal
Oscillator
Block
WDT, PWRT, Fail-Safe Clock Monitor
16 MHz
Internal Oscillator
(HFINTOSC)
Clock
Control
SCS<1:0>
HFPLL
31 kHz (LFINTOSC)
Two-Speed Start-up and other modules
Oscillator
31 kHz
Source
500 kHz
(MFINTOSC)
125 kHz
31.25 kHz
62.5 kHz
FOSC<2:0> = 100
Peripherals
Sleep
External
Timer1
2008-2011 Microchip Technology Inc. DS41364E-page 69
PIC16(L)F1934/6/7
5.2 Clock Source Types
Clock sources can be classified as external or internal.
External clock sources rely on external circuitry for the
clock source to function. Examples are: oscillator mod-
ules (EC mode), quartz crystal resonators or ceramic
resonators (LP, XT and HS modes) and Resis-
tor-Capacitor (RC) mode circuits.
Internal clock sources are contained internally within
the oscillator module. The internal oscillator block has
two internal oscillators and a dedicated Phase-Lock
Loop (HFPLL) that are used to generate three internal
system clock sources: the 16 MHz High-Frequency
Internal Oscillator (HFINTOSC), 500 kHz (MFINTOSC)
and the 31 kHz Low-Frequency Internal Oscillator
(LFINTOSC).
The system clock can be selected between external or
internal clock sources via the System Clock Select
(SCS) bits in the OSCCON register. See Section 5.3
“Clock Switching” for additional information.
5.2.1 EXTERNAL CLOCK SOURCES
An external clock source can be used as the device
system clock by performing one of the following
actions:
Program the FOSC<2:0> bits in the Configuration
Word 1 to select an external clock source that will
be used as the default system clock upon a
device Reset.
Write the SCS<1:0> bits in the OSCCON register
to switch the system clock source to:
- Timer1 Oscillator during run-time, or
- An external clock source determined by the
value of the FOSC bits.
See Section 5.3 “Clock Switchingfor more informa-
tion.
5.2.1.1 EC Mode
The External Clock (EC) mode allows an externally
generated logic level signal to be the system clock
source. When operating in this mode, an external clock
source is connected to the OSC1 input.
OSC2/CLKOUT is available for general purpose I/O or
CLKOUT. Figure 5-2 shows the pin connections for EC
mode.
EC mode has 3 power modes to select from through
Configuration Word 1:
High power, 4-32 MHz (FOSC = 111)
Medium power, 0.5-4 MHz (FOSC = 110)
Low power, 0-0.5 MHz (FOSC = 101)
The Oscillator Start-up Timer (OST) is disabled when
EC mode is selected. Therefore, there is no delay in
operation after a Power-on Reset (POR) or wake-up
from Sleep. Because the PIC® MCU design is fully
static, stopping the external clock input will have the
effect of halting the device while leaving all data intact.
Upon restarting the external clock, the device will
resume operation as if no time had elapsed.
FIGURE 5-2: EXTERNAL CLOCK (EC)
MODE OPERATION
5.2.1.2 LP, XT, HS Modes
The LP, XT and HS modes support the use of quartz
crystal resonators or ceramic resonators connected to
OSC1 and OSC2 (Figure 5-3). The three modes select
a low, medium or high gain setting of the internal
inverter-amplifier to support various resonator types
and speed.
LP Oscillator mode selects the lowest gain setting of the
internal inverter-amplifier. LP mode current consumption
is the least of the three modes. This mode is designed to
drive only 32.768 kHz tuning-fork type crystals (watch
crystals).
XT Oscillator mode selects the intermediate gain
setting of the internal inverter-amplifier. XT mode
current consumption is the medium of the three modes.
This mode is best suited to drive resonators with a
medium drive level specification.
HS Oscillator mode selects the highest gain setting of the
internal inverter-amplifier. HS mode current consumption
is the highest of the three modes. This mode is best
suited for resonators that require a high drive setting.
Figure 5-3 and Figure 5-4 show typical circuits for
quartz crystal and ceramic resonators, respectively.
OSC1/CLKIN
OSC2/CLKOUT
Clock from
Ext. System PIC® MCU
FOSC/4 or I/O(1)
Note 1: Output depends upon CLKOUTEN bit of the
Configuration Word 1.
PIC16(L)F1934/6/7
DS41364E-page 70 2008-2011 Microchip Technology Inc.
FIGURE 5-3: QUARTZ CRYSTAL
OPERATION (LP, XT OR
HS MODE)
FIGURE 5-4: CERAMIC RESONATOR
OPERATION
(XT OR HS MODE)
5.2.1.3 Oscillator Start-up Timer (OST)
If the oscillator module is configured for LP, XT or HS
modes, the Oscillator Start-up Timer (OST) counts
1024 oscillations from OSC1. This occurs following a
Power-on Reset (POR) and when the Power-up Timer
(PWRT) has expired (if configured), or a wake-up from
Sleep. During this time, the program counter does not
increment and program execution is suspended. The
OST ensures that the oscillator circuit, using a quartz
crystal resonator or ceramic resonator, has started and
is providing a stable system clock to the oscillator
module.
In order to minimize latency between external oscillator
start-up and code execution, the Two-Speed Clock
Start-up mode can be selected (see Section 5.4
“Two-Speed Clock Start-up Mode”).
5.2.1.4 4X PLL
The oscillator module contains a 4X PLL that can be
used with both external and internal clock sources to
provide a system clock source. The input frequency for
the 4X PLL must fall within specifications. See the PLL
Clock Timing specifications in the applicable Electrical
Specifications Chapter.
The 4X PLL may be enabled for use by one of two
methods:
1. Program the PLLEN bit in Configuration Word 2
to a ‘1’.
2. Write the SPLLEN bit in the OSCCON register to
a ‘1’. If the PLLEN bit in Configuration Word 2 is
programmed to a ‘1’, then the value of SPLLEN
is ignored.
Note 1: Quartz crystal characteristics vary
according to type, package and
manufacturer. The user should consult the
manufacturer data sheets for specifications
and recommended application.
2: Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
3: For oscillator design assistance, reference
the following Microchip Applications Notes:
• AN826, “Crystal Oscillator Basics and
Crystal Selection for rfPIC® and PIC®
Devices” (DS00826)
• AN849, “Basic PIC® Oscillator Design
(DS00849)
• AN943, “Practical PIC® Oscillator
Analysis and Design” (DS00943)
• AN949, “Making Y our Oscillator Work
(DS00949)
Note 1: A series resistor (RS) may be required for
quartz crystals with low drive level.
2: The value of RF varies with the Oscillator mode
selected (typically between 2 M to 10 M.
C1
C2
Quartz
RS(1)
OSC1/CLKIN
RF(2) Sleep
To Internal
Logic
PIC® MCU
Crystal
OSC2/CLKOUT
Note 1: A series resistor (RS) may be required for
ceramic resonators with low drive level.
2: The value of RF varies with the Oscillator mode
selected (typically between 2 M to 10 M.
3: An additional parallel feedback resistor (RP)
may be required for proper ceramic resonator
operation.
C1
C2 Ceramic RS(1)
OSC1/CLKIN
RF(2) Sleep
To Internal
Logic
PIC® MCU
RP(3)
Resonator
OSC2/CLKOUT
2008-2011 Microchip Technology Inc. DS41364E-page 71
PIC16(L)F1934/6/7
5.2.1.5 TIMER1 Oscillator
The Timer1 Oscillator is a separate crystal oscillator
that is associated with the Timer1 peripheral. It is opti-
mized for timekeeping operations with a 32.768 kHz
crystal connected between the T1OSO and T1OSI
device pins.
The Timer1 Oscillator can be used as an alternate sys-
tem clock source and can be selected during run-time
using clock switching. Refer to Section 5.3 “Clock
Switching” for more information.
FIGURE 5-5: QUARTZ CRYSTAL
OPERATION (TIMER1
OSCILLATOR)
5.2.1.6 External RC Mode
The external Resistor-Capacitor (RC) modes support
the use of an external RC circuit. This allows the
designer maximum flexibility in frequency choice while
keeping costs to a minimum when clock accuracy is not
required.
The RC circuit connects to OSC1. OSC2/CLKOUT is
available for general purpose I/O or CLKOUT. The
function of the OSC2/CLKOUT pin is determined by the
state of the CLKOUTEN bit in Configuration Word 1.
Figure 5-6 shows the external RC mode connections.
FIGURE 5-6: EXTERNAL RC MODES
The RC oscillator frequency is a function of the supply
voltage, the resistor (REXT) and capacitor (CEXT) values
and the operating temperature. Other factors affecting
the oscillator frequency are:
threshold voltage variation
component tolerances
packaging variations in capacitance
The user also needs to take into account variation due
to tolerance of external RC components used.
Note 1: Quartz crystal characteristics vary
according to type, package and
manufacturer. The user should consult the
manufacturer data sheets for specifications
and recommended application.
2: Always verify oscillator performance over
the VDD and temperature range that is
expected for the application.
3: For oscillator design assistance, reference
the following Microchip Applications Notes:
• AN826, “Crystal Oscillator Basics and
Crystal Selection for rfPIC® and PIC®
Devices” (DS00826)
• AN849, “Basic PIC® Oscillator Design
(DS00849)
• AN943, “Practical PIC® Oscillator
Analysis and Design” (DS00943)
• AN949, “Making Y our Oscillator Work
(DS00949)
• TB097, “Interfacing a Micro Crystal
MS1V -T1K 32.768 kHz Tuning Fork
Crystal to a PIC16F690/SS” (DS91097)
• AN1288, “Design Practices for
Low-Power External Oscillators
(DS01288)
C1
C2
32.768 kHz
T1OSI
To Internal
Logic
PIC® MCU
Crystal
T1OSO
Quartz
OSC2/CLKOUT
CEXT
REXT
PIC® MCU
OSC1/CLKIN
FOSC/4 or
Internal
Clock
VDD
VSS
Recommended values: 10 k REXT 100 k, <3V
3 k REXT 100 k, 3-5V
CEXT > 20 pF, 2-5V
Note 1: Output depends upon CLKOUTEN bit of the
Configuration Word 1.
I/O(1)
PIC16(L)F1934/6/7
DS41364E-page 72 2008-2011 Microchip Technology Inc.
5.2.2 INTERNAL CLOCK SOURCES
The device may be configured to use the internal oscil-
lator block as the system clock by performing one of the
following actions:
Program the FOSC<2:0> bits in Configuration
Word 1 to select the INTOSC clock source, which
will be used as the default system clock upon a
device Reset.
Write the SCS<1:0> bits in the OSCCON register
to switch the system clock source to the internal
oscillator during run-time. See Section 5.3
“Clock Switching”for more information.
In INTOSC mode, OSC1/CLKIN is available for general
purpose I/O. OSC2/CLKOUT is available for general
purpose I/O or CLKOUT.
The function of the OSC2/CLKOUT pin is determined
by the state of the CLKOUTEN bit in Configuration
Word 1.
The internal oscillator block has two independent
oscillators and a dedicated Phase-Lock Loop, HFPLL
that can produce one of three internal system clock
sources.
1. The HFINTOSC (High-Frequency Internal
Oscillator) is factory calibrated and operates at
16 MHz. The HFINTOSC source is generated
from the 500 kHz MFINTOSC source and the
dedicated Phase-Lock Loop, HFPLL. The
frequency of the HFINTOSC can be
user-adjusted via software using the OSCTUNE
register (Register 5-3).
2. The MFINTOSC (Medium-Frequency Internal
Oscillator) is factory calibrated and operates at
500 kHz. The frequency of the MFINTOSC can
be user-adjusted via software using the
OSCTUNE register (Register 5-3).
3. The LFINTOSC (Low-Frequency Internal
Oscillator) is uncalibrated and operates at
31 kHz.
5.2.2.1 HFINTOSC
The High-Frequency Internal Oscillator (HFINTOSC) is
a factory calibrated 16 MHz internal clock source. The
frequency of the HFINTOSC can be altered via
software using the OSCTUNE register (Register 5-3).
The output of the HFINTOSC connects to a postscaler
and multiplexer (see Figure 5-1). One of nine
frequencies derived from the HFINTOSC can be
selected via software using the IRCF<3:0> bits of the
OSCCON register. See Section 5.2.2.7 “Internal
Oscillator Clock Switch Timing” for more information.
The HFINTOSC is enabled by:
Configure the IRCF<3:0> bits of the OSCCON
register for the desired HF frequency, and
•FOSC<2:0> = 100, or
Set the System Clock Source (SCS) bits of the
OSCCON register to ‘1x’.
The High-Frequency Internal Oscillator Ready bit
(HFIOFR) of the OSCSTAT register indicates when the
HFINTOSC is running and can be utilized.
The High-Frequency Internal Oscillator Status Locked
bit (HFIOFL) of the OSCSTAT register indicates when
the HFINTOSC is running within 2% of its final value.
The High-Frequency Internal Oscillator Status Stable
bit (HFIOFS) of the OSCSTAT register indicates when
the HFINTOSC is running within 0.5% of its final value.
5.2.2.2 MFINTOSC
The Medium-Frequency Internal Oscillator
(MFINTOSC) is a factory calibrated 500 kHz internal
clock source. The frequency of the MFINTOSC can be
altered via software using the OSCTUNE register
(Register 5-3).
The output of the MFINTOSC connects to a postscaler
and multiplexer (see Figure 5-1). One of nine
frequencies derived from the MFINTOSC can be
selected via software using the IRCF<3:0> bits of the
OSCCON register. See Section 5.2.2.7 “Internal
Oscillator Clock Switch Timing” for more information.
The MFINTOSC is enabled by:
Configure the IRCF<3:0> bits of the OSCCON
register for the desired HF frequency, and
•FOSC<2:0> = 100, or
Set the System Clock Source (SCS) bits of the
OSCCON register to ‘1x
The Medium-Frequency Internal Oscillator Ready bit
(MFIOFR) of the OSCSTAT register indicates when the
MFINTOSC is running and can be utilized.
2008-2011 Microchip Technology Inc. DS41364E-page 73
PIC16(L)F1934/6/7
5.2.2.3 Internal Oscillator Frequency
Adjustment
The 500 kHz internal oscillator is factory calibrated.
This internal oscillator can be adjusted in software by
writing to the OSCTUNE register (Register 5-3). Since
the HFINTOSC and MFINTOSC clock sources are
derived from the 500 kHz internal oscillator a change in
the OSCTUNE register value will apply to both.
The default value of the OSCTUNE register is ‘0’. The
value is a 5-bit two’s complement number. A value of
0Fh will provide an adjustment to the maximum
frequency. A value of 10h will provide an adjustment to
the minimum frequency.
When the OSCTUNE register is modified, the oscillator
frequency will begin shifting to the new frequency. Code
execution continues during this shift. There is no
indication that the shift has occurred.
OSCTUNE does not affect the LFINTOSC frequency.
Operation of features that depend on the LFINTOSC
clock source frequency, such as the Power-up Timer
(PWRT), Watchdog Timer (WDT), Fail-Safe Clock
Monitor (FSCM) and peripherals, are not affected by the
change in frequency.
5.2.2.4 LFINTOSC
The Low-Frequency Internal Oscillator (LFINTOSC) is
an uncalibrated 31 kHz internal clock source.
The output of the LFINTOSC connects to a postscaler
and multiplexer (see Figure 5-1). Select 31 kHz, via
software, using the IRCF<3:0> bits of the OSCCON
register. See Section 5.2.2.7 “Internal Oscillator
Clock Switch Timing” for more information. The
LFINTOSC is also the frequency for the Power-up Timer
(PWRT), Watchdog Timer (WDT) and Fail-Safe Clock
Monitor (FSCM).
The LFINTOSC is enabled by selecting 31 kHz
(IRCF<3:0> bits of the OSCCON register = 000) as the
system clock source (SCS bits of the OSCCON
register = 1x), or when any of the following are
enabled:
Configure the IRCF<3:0> bits of the OSCCON
register for the desired LF frequency, and
•FOSC<2:0> = 100, or
Set the System Clock Source (SCS) bits of the
OSCCON register to1x
Peripherals that use the LFINTOSC are:
Power-up Timer (PWRT)
Watchdog Timer (WDT)
Fail-Safe Clock Monitor (FSCM)
The Low-Frequency Internal Oscillator Ready bit
(LFIOFR) of the OSCSTAT register indicates when the
LFINTOSC is running and can be utilized.
5.2.2.5 Internal Oscillator Frequency
Selection
The system clock speed can be selected via software
using the Internal Oscillator Frequency Select bits
IRCF<3:0> of the OSCCON register.
The output of the 16 MHz HFINTOSC and 31 kHz
LFINTOSC connects to a postscaler and multiplexer
(see Figure 5-1). The Internal Oscillator Frequency
Select bits IRCF<3:0> of the OSCCON register select
the frequency output of the internal oscillators. One of
the following frequencies can be selected via software:
32 MHz (requires 4X PLL)
•16 MHz
•8 MHz
•4 MHz
•2 MHz
•1 MHz
500 kHz (Default after Reset)
•250 kHz
•125 kHz
•62.5 kHz
•31.25 kHz
31 kHz (LFINTOSC)
The IRCF<3:0> bits of the OSCCON register allow
duplicate selections for some frequencies. These dupli-
cate choices can offer system design trade-offs. Lower
power consumption can be obtained when changing
oscillator sources for a given frequency. Faster transi-
tion times can be obtained between frequency changes
that use the same oscillator source.
Note: Following any Reset, the IRCF<3:0> bits
of the OSCCON register are set to ‘0111
and the frequency selection is set to
500 kHz. The user can modify the IRCF
bits to select a different frequency.
PIC16(L)F1934/6/7
DS41364E-page 74 2008-2011 Microchip Technology Inc.
5.2.2.6 32 MHz Internal Oscillator
Frequency Selection
The Internal Oscillator Block can be used with the 4X
PLL associated with the External Oscillator Block to
produce a 32 MHz internal system clock source. The
following settings are required to use the 32 MHz inter-
nal clock source:
The FOSC bits in Configuration Word 1 must be
set to use the INTOSC source as the device sys-
tem clock (FOSC<2:0> = 100).
The SCS bits in the OSCCON register must be
cleared to use the clock determined by
FOSC<2:0> in Configuration Word 1
(SCS<1:0> = 00).
The IRCF bits in the OSCCON register must be
set to the 8 MHz HFINTOSC set to use
(IRCF<3:0> = 1110).
The SPLLEN bit in the OSCCON register must be
set to enable the 4xPLL, or the PLLEN bit of the
Configuration Word 2 must be programmed to a
1’.
The 4xPLL is not available for use with the internal
oscillator when the SCS bits of the OSCCON register
are set to1x’. The SCS bits must be set to ‘00’ to use
the 4xPLL with the internal oscillator.
5.2.2.7 Internal Oscillator Clock Switch
Timing
When switching between the HFINTOSC, MFINTOSC
and the LFINTOSC, the new oscillator may already be
shut down to save power (see Figure 5-7). If this is the
case, there is a delay after the IRCF<3:0> bits of the
OSCCON register are modified before the frequency
selection takes place. The OSCSTAT register will
reflect the current active status of the HFINTOSC,
MFINTOSC and LFINTOSC oscillators. The sequence
of a frequency selection is as follows:
1. IRCF<3:0> bits of the OSCCON register are
modified.
2. If the new clock is shut down, a clock start-up
delay is started.
3. Clock switch circuitry waits for a falling edge of
the current clock.
4. The current clock is held low and the clock
switch circuitry waits for a rising edge in the new
clock.
5. The new clock is now active.
6. The OSCSTAT register is updated as required.
7. Clock switch is complete.
See Figure 5-7 for more details.
If the internal oscillator speed is switched between two
clocks of the same source, there is no start-up delay
before the new frequency is selected. Clock switching
time delays are shown in Table 5-1.
Start-up delay specifications are located in the
oscillator tables in the applicable Electrical
Specifications Chapter.
Note: When using the PLLEN bit of the
Configuration Word 2, the 4xPLL cannot
be disabled by software and the 8 MHz
HFINTOSC option will no longer be
available.
2008-2011 Microchip Technology Inc. DS41364E-page 75
PIC16(L)F1934/6/7
FIGURE 5-7: INTERNAL OSCILLA TOR SWITCH TIMING
HFINTOSC/
LFINTOSC
IRCF <3:0>
System Clock
HFINTOSC/
LFINTOSC
IRCF <3:0>
System Clock
00
00
Start-up Time 2-cycle Sync Running
2-cycle Sync Running
HFINTOSC/ LFINTOSC (FSCM and WDT disabled)
HFINTOSC/ LFINTOSC (Either FSCM or WDT enabled)
LFINTOSC
HFINTOSC/
IRCF <3:0>
System Clock
= 0 0
Start-up Time 2-cycle Sync Running
LFINTOSC HFINTOSC/MFINTOSC LFINTOSC turns off unless WDT or FSCM is enabled
MFINTOSC
MFINTOSC
MFINTOSC
MFINTOSC
MFINTOSC
PIC16(L)F1934/6/7
DS41364E-page 76 2008-2011 Microchip Technology Inc.
5.3 Clock Switching
The system clock source can be switched between
external and internal clock sources via software using
the System Clock Select (SCS) bits of the OSCCON
register. The following clock sources can be selected
using the SCS bits:
Default system oscillator determined by FOSC
bits in Configuration Word 1
Timer1 32 kHz crystal oscillator
Internal Oscillator Block (INTOSC)
5.3.1 SYSTEM CLOCK SELECT (SCS)
BITS
The System Clock Select (SCS) bits of the OSCCON
register selects the system clock source that is used for
the CPU and peripherals.
When the SCS bits of the OSCCON register = 00,
the system clock source is determined by value of
the FOSC<2:0> bits in the Configuration Word 1.
When the SCS bits of the OSCCON register = 01,
the system clock source is the Timer1 oscillator.
When the SCS bits of the OSCCON register = 1x,
the system clock source is chosen by the internal
oscillator frequency selected by the IRCF<3:0>
bits of the OSCCON register. After a Reset, the
SCS bits of the OSCCON register are always
cleared.
When switching between clock sources, a delay is
required to allow the new clock to stabilize. These oscil-
lator delays are shown in Table 5-1.
5.3.2 OSCILLATOR START-UP TIME-OUT
STATUS (OSTS) BIT
The Oscillator Start-up Time-out Status (OSTS) bit of
the OSCSTAT register indicates whether the system
clock is running from the external clock source, as
defined by the FOSC<2:0> bits in the Configuration
Word 1, or from the internal clock source. In particular,
OSTS indicates that the Oscillator Start-up Timer
(OST) has timed out for LP, XT or HS modes. The OST
does not reflect the status of the Timer1 oscillator.
5.3.3 TIMER1 OSCILLATOR
The Timer1 oscillator is a separate crystal oscillator
associated with the Timer1 peripheral. It is optimized
for timekeeping operations with a 32.768 kHz crystal
connected between the T1OSO and T1OSI device
pins.
The Timer1 oscillator is enabled using the T1OSCEN
control bit in the T1CON register. See Section 21.0
“Timer1 Module with Gate Control” for more
information about the Timer1 peripheral.
5.3.4 TIMER1 OSCILLATOR READY
(T1OSCR) BIT
The user must ensure that the Timer1 oscillator is
ready to be used before it is selected as a system clock
source. The Timer1 Oscillator Ready (T1OSCR) bit of
the OSCSTAT register indicates whether the Timer1
oscillator is ready to be used. After the T1OSCR bit is
set, the SCS bits can be configured to select the Timer1
oscillator.
Note: Any automatic clock switch, which may
occur from Two-Speed Start-up or
Fail-Safe Clock Monitor, does not update
the SCS bits of the OSCCON register. The
user can monitor the OSTS bit of the
OSCSTAT register to determine the current
system clock source.
2008-2011 Microchip Technology Inc. DS41364E-page 77
PIC16(L)F1934/6/7
5.4 Two-Speed Clock Start-up Mode
Two-Speed Start-up mode provides additional power
savings by minimizing the latency between external
oscillator start-up and code execution. In applications
that make heavy use of the Sleep mode, Two-Speed
Start-up will remove the external oscillator start-up
time from the time spent awake and can reduce the
overall power consumption of the device. This mode
allows the application to wake-up from Sleep, perform
a few instructions using the INTOSC internal oscillator
block as the clock source and go back to Sleep without
waiting for the external oscillator to become stable.
Two-Speed Start-up provides benefits when the oscil-
lator module is configured for LP, XT or HS modes.
The Oscillator Start-up Timer (OST) is enabled for
these modes and must count 1024 oscillations before
the oscillator can be used as the system clock source.
If the oscillator module is configured for any mode
other than LP, XT or HS mode, then Two-Speed
Start-up is disabled. This is because the external clock
oscillator does not require any stabilization time after
POR or an exit from Sleep.
If the OST count reaches 1024 before the device
enters Sleep mode, the OSTS bit of the OSCSTAT reg-
ister is set and program execution switches to the
external oscillator. However, the system may never
operate from the external oscillator if the time spent
awake is very short.
5.4.1 TWO-SPEED START-UP MODE
CONFIGURATION
Two-Speed Start-up mode is configured by the
following settings:
IESO (of the Configuration Word 1) = 1; Inter-
nal/External Switchover bit (Two-Speed Start-up
mode enabled).
SCS (of the OSCCON register) = 00.
FOSC<2:0> bits in the Configuration Word 1
configured for LP, XT or HS mode.
Two-Speed Start-up mode is entered after:
Power-on Reset (POR) and, if enabled, after
Power-up Timer (PWRT) has expired, or
Wake-up from Sleep.
TABLE 5-1: OSCILLATOR SWITCHING DELAYS
Note: Executing a SLEEP instruction will abort
the oscillator start-up time and will cause
the OSTS bit of the OSCSTAT register to
remain clear.
Switch From Switch To Frequency Oscillator Delay
Sleep/POR
LFINTOSC(1)
MFINTOSC(1)
HFINTOSC(1)
31 kHz
31.25 kHz-500 kHz
31.25kHz-16MHz
Oscillator Warm-up Delay (TWARM)
Sleep/POR EC, RC(1) DC – 32 MHz 2 cycles
LFINTOSC EC, RC(1) DC – 32 MHz 1 cycle of each
Sleep/POR Timer1 Oscillator
LP, XT, HS(1) 32 kHz-20 MHz 1024 Clock Cycles (OST)
Any clock source MFINTOSC(1)
HFINTOSC(1) 31.25 kHz-500 kHz
31.25kHz-16MHz 2s (approx.)
Any clock source LFINTOSC(1) 31 kHz 1 cycle of each
Any clock source Timer1 Oscillator 32 kHz 1024 Clock Cycles (OST)
PLL inactive PLL active 16-32 MHz 2 ms (approx.)
Note 1: PLL inactive.
PIC16(L)F1934/6/7
DS41364E-page 78 2008-2011 Microchip Technology Inc.
5.4.2 TWO-SPEED START-UP
SEQUENCE
1. Wake-up from Power-on Reset or Sleep.
2. Instructions begin execution by the internal
oscillator at the frequency set in the IRCF<3:0>
bits of the OSCCON register.
3. OST enabled to count 1024 clock cycles.
4. OST timed out, wait for falling edge of the
internal oscillator.
5. OSTS is set.
6. System clock held low until the next falling edge
of new clock (LP, XT or HS mode).
7. System clock is switched to external clock
source.
5.4.3 CHECKING TWO-SPEED CLOCK
STATUS
Checking the state of the OSTS bit of the OSCSTAT
register will confirm if the microcontroller is running
from the external clock source, as defined by the
FOSC<2:0> bits in the Configuration Word 1, or the
internal oscillator.
FIGURE 5-8: TWO-SPEED START-UP
0 1 1022 1023
PC + 1
TOSTT
INTOSC
OSC1
OSC2
Program Counter
System Clock
PC - N PC
2008-2011 Microchip Technology Inc. DS41364E-page 79
PIC16(L)F1934/6/7
5.5 Fail-Safe Clock Monitor
The Fail-Safe Clock Monitor (FSCM) allows the device
to continue operating should the external oscillator fail.
The FSCM can detect oscillator failure any time after
the Oscillator Start-up Timer (OST) has expired. The
FSCM is enabled by setting the FCMEN bit in the
Configuration Word 1. The FSCM is applicable to all
external Oscillator modes (LP, XT, HS, EC, Timer1
oscillator and RC).
FIGURE 5-9: FSCM BLOCK DIAGRAM
5.5.1 FAIL-SAFE DETECTION
The FSCM module detects a failed oscillator by
comparing the external oscillator to the FSCM sample
clock. The sample clock is generated by dividing the
LFINTOSC by 64. See Figure 5-9. Inside the fail
detector block is a latch. The external clock sets the
latch on each falling edge of the external clock. The
sample clock clears the latch on each rising edge of the
sample clock. A failure is detected when an entire
half-cycle of the sample clock elapses before the
external clock goes low.
5.5.2 FAIL-SAFE OPERATION
When the external clock fails, the FSCM switches the
device clock to an internal clock source and sets the bit
flag OSFIF of the PIR2 register. Setting this flag will
generate an interrupt if the OSFIE bit of the PIE2
register is also set. The device firmware can then take
steps to mitigate the problems that may arise from a
failed clock. The system clock will continue to be
sourced from the internal clock source until the device
firmware successfully restarts the external oscillator
and switches back to external operation.
The internal clock source chosen by the FSCM is
determined by the IRCF<3:0> bits of the OSCCON
register. This allows the internal oscillator to be
configured before a failure occurs.
5.5.3 FAIL-SAFE CONDITION CLEARING
The Fail-Safe condition is cleared after a Reset,
executing a SLEEP instruction or changing the SCS bits
of the OSCCON register. When the SCS bits are
changed, the OST is restarted. While the OST is
running, the device continues to operate from the
INTOSC selected in OSCCON. When the OST times
out, the Fail-Safe condition is cleared and the device
will be operating from the external clock source. The
Fail-Safe condition must be cleared before the OSFIF
flag can be cleared.
5.5.4 RESET OR WAKE-UP FROM SLEEP
The FSCM is designed to detect an oscillator failure
after the Oscillator Start-up Timer (OST) has expired.
The OST is used after waking up from Sleep and after
any type of Reset. The OST is not used with the EC or
RC clock modes so that the FSCM will be active as
soon as the Reset or wake-up has completed. When
the FSCM is enabled, the Two-Speed Start-up is also
enabled. Therefore, the device will always be executing
code while the OST is operating.
External
LFINTOSC ÷ 64
S
R
Q
31 kHz
(~32 s)
488 Hz
(~2 ms)
Clock Monitor
Latch
Clock
Failure
Detected
Oscillator
Clock
Q
Sample Clock
Note: Due to the wide range of oscillator start-up
times, the Fail-Safe circuit is not active
during oscillator start-up (i.e., after exiting
Reset or Sleep). After an appropriate
amount of time, the user should check the
Status bits in the OSCSTAT register to
verify the oscillator start-up and that the
system clock switchover has successfully
completed.
PIC16(L)F1934/6/7
DS41364E-page 80 2008-2011 Microchip Technology Inc.
FIGURE 5-10: FSCM TIMING DIAGRAM
OSCFIF
System
Clock
Output
Sample Clock
Failure
Detected
Oscillator
Failure
Note: The system clock is normally at a much higher frequency than the sample clock. The relative frequencies in
this example have been chosen for clarity.
(Q)
Te s t Test Test
Clock Monitor Output
2008-2011 Microchip Technology Inc. DS41364E-page 81
PIC16(L)F1934/6/7
5.6 Oscillator Control Registers
REGISTER 5-1: OSCCON: OSCILLATOR CONTROL REGISTER
R/W-0/0 R/W-0/0 R/W-1/1 R/W-1/1 R/W-1/1 U-0 R/W-0/0 R/W-0/0
SPLLEN IRCF<3:0> SCS<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 SPLLEN: Software PLL Enable bit
If PLLEN in Configuration Word 1 = 1:
SPLLEN bit is ignored. 4x PLL is always enabled (subject to oscillator requirements)
If PLLEN in Configuration Word 1 = 0:
1 = 4x PLL Is enabled
0 = 4x PLL is disabled
bit 6-3 IRCF<3:0>: Internal Oscillator Frequency Select bits
000x =31 kHz LF
0010 =31.25 kHz MF
0011 =31.25 kHz HF
(1)
0100 =62.5kHz MF
0101 =125kHz MF
0110 =250kHz MF
0111 = 500 kHz MF (default upon Reset)
1000 =125kHz HF
(1)
1001 =250kHz HF
(1)
1010 =500kHz HF
(1)
1011 =1MHz HF
1100 =2MHz HF
1101 =4MHz HF
1110 = 8 MHz or 32 MHz HF(see Section 5.2.2.1 “HFINTOSC”)
1111 = 16 MHz HF
bit 2 Unimplemented: Read as ‘0
bit 1-0 SCS<1:0>: System Clock Select bits
1x = Internal oscillator block
01 = Timer1 oscillator
00 = Clock determined by FOSC<2:0> in Configuration Word 1.
Note 1: Duplicate frequency derived from HFINTOSC.
PIC16(L)F1934/6/7
DS41364E-page 82 2008-2011 Microchip Technology Inc.
REGISTER 5-2: OSCSTAT: OSCILLATOR ST ATUS REGISTER
R-1/q R-0/q R-q/q R-0/q R-0/q R-q/q R-0/0 R-0/q
T1OSCR PLLR OSTS HFIOFR HFIOFL MFIOFR LFIOFR HFIOFS
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared q = Conditional
bit 7 T1OSCR: Timer1 Oscillator Ready bit
If T1OSCEN = 1:
1 = Timer1 oscillator is ready
0 = Timer1 oscillator is not ready
If T1OSCEN = 0:
1 = Timer1 clock source is always ready
bit 6 PLLR 4x PLL Ready bit
1 = 4x PLL is ready
0 = 4x PLL is not ready
bit 5 OSTS: Oscillator Start-up Time-out Status bit
1 = Running from the clock defined by the FOSC<2:0> bits of the Configuration Word 1
0 = Running from an internal oscillator (FOSC<2:0> = 100)
bit 4 HFIOFR: High-Frequency Internal Oscillator Ready bit
1 = HFINTOSC is ready
0 = HFINTOSC is not ready
bit 3 HFIOFL: High-Frequency Internal Oscillator Locked bit
1 = HFINTOSC is at least 2% accurate
0 = HFINTOSC is not 2% accurate
bit 2 MFIOFR: Medium-Frequency Internal Oscillator Ready bit
1 = MFINTOSC is ready
0 = MFINTOSC is not ready
bit 1 LFIOFR: Low-Frequency Internal Oscillator Ready bit
1 = LFINTOSC is ready
0 = LFINTOSC is not ready
bit 0 HFIOFS: High-Frequency Internal Oscillator Stable bit
1 = HFINTOSC is at least 0.5% accurate
0 = HFINTOSC is not 0.5% accurate
2008-2011 Microchip Technology Inc. DS41364E-page 83
PIC16(L)F1934/6/7
TABLE 5-2: SUMMARY OF REGISTERS ASSOCIATED WITH CLOCK SOURCES
TABLE 5-3: SUMMARY OF CONFIGURATION WORD WITH CLOCK SOURCES
REGISTER 5-3: OSCTUNE: OSCILLATOR TUNING REGISTER
U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
TUN<5:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-6 Unimplemented: Read as0
bit 5-0 TUN<4:0>: Frequency Tuning bits
011111 = Maximum frequency
011110 =
000001 =
000000 = Oscillator module is running at the factory-calibrated frequency.
111111 =
100000 = Minimum frequency
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
OSCCON SPLLEN IRCF<3:0> —SCS<1:0>81
OSCSTAT T1OSCR PLLR OSTS HFIOFR HFIOFL MFIOFR LFIOFR HFIOFS 82
OSCTUNE —TUN<5:0>83
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE(1) 100
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF(1) 103
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC TMR1ON 203
Legend: = unimplemented location, read as ‘0’. Shaded cells are not used by clock sources.
Note 1: PIC16F1934 only.
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0 Register
on Pa ge
CONFIG1 13:8 FCMEN IESO CLKOUTEN BOREN<1:0> CPD 62
7:0 CP MCLRE PWRTE WDTE<1:0> FOSC<2:0>
CONFIG2 13:8 LVP DEBUG BORV STVREN PLLEN 64
7:0 VCAPEN<1:0>(1) WRT<1:0>
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by clock sources.
Note 1: PIC16F1934/6/7 only.
PIC16(L)F1934/6/7
DS41364E-page 84 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 85
PIC16(L)F1934/6/7
6.0 RESETS
There are multiple ways to reset this device:
Power-on Reset (POR)
Brown-out Reset (BOR)
•MCLR
Reset
•WDT Reset
RESET instruction
Stack Overflow
Stack Underflow
Programming mode exit
To a l lo w V DD to stabilize, an optional power-up timer
can be enabled to extend the Reset time after a BOR
or POR event.
A simplified block diagram of the On-Chip Reset Circuit
is shown in Figure 6-1.
FIGURE 6-1: SI MPLI FIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
External Reset
MCLR
VDD
WDT
Time-out
Power-on
Reset
LFINTOSC
PWRT
64 ms
PWRTEN
Brown-out
Reset
BOR
RESET Instruction
Stack
Pointer
Stack Overflow/Underflow Reset
Sleep
MCLRE
Enable
Device
Reset
Zero
Programming Mode Exit
PIC16(L)F1934/6/7
DS41364E-page 86 2008-2011 Microchip Technology Inc.
6.1 Power-on Reset (POR)
The POR circuit holds the device in Reset until VDD has
reached an acceptable level for minimum operation.
Slow rising VDD, fast operating speeds or analog
performance may require greater than minimum VDD.
The PWRT, BOR or MCLR features can be used to
extend the start-up period until all device operation
conditions have been met.
6.1.1 POWER-UP TIMER (PWRT)
The Power-up Timer provides a nominal 64 ms time-
out on POR or Brown-out Reset.
The device is held in Reset as long as PWRT is active.
The PWRT delay allows additional time for the VDD to
rise to an acceptable level. The Power-up Timer is
enabled by clearing the PWRTE bit in Configuration
Word 1.
The Power-up Timer starts after the release of the POR
and BOR.
For additional information, refer to Application Note
AN607, “Power-up Trouble Shooting” (DS00607).
6.2 Brown-Out Reset (BOR)
The BOR circuit holds the device in Reset when VDD
reaches a selectable minimum level. Between the
POR and BOR, complete voltage range coverage for
execution protection can be implemented.
The Brown-out Reset module has four operating
modes controlled by the BOREN<1:0> bits in Configu-
ration Word 1. The four operating modes are:
BOR is always on
BOR is off when in Sleep
BOR is controlled by software
BOR is always off
Refer to Table 6- 3 for more information.
The Brown-out Reset voltage level is selectable by
configuring the BORV bit in Configuration Word 2.
A VDD noise rejection filter prevents the BOR from trig-
gering on small events. If VDD falls below VBOR for a
duration greater than parameter TBORDC, the device
will reset. See Figure 6-2 for more information.
TABLE 6-1: BOR OPERATING MODES
6.2.1 BOR IS ALWAYS ON
When the BOREN bits of Configuration Word 1 are set
to ‘11’, the BOR is always on. The device start-up will
be delayed until the BOR is ready and VDD is higher
than the BOR threshold.
BOR protection is active during Sleep. The BOR does
not delay wake-up from Sleep.
6.2.2 BOR IS OFF IN SLEEP
When the BOREN bits of Configuration Word 1 are set
to ‘10’, the BOR is on, except in Sleep. The device
start-up will be delayed until the BOR is ready and VDD
is higher than the BOR threshold.
BOR protection is not active during Sleep. The device
wake-up will be delayed until the BOR is ready.
6.2.3 BOR CONTROLLED BY SOFTWARE
When the BOREN bits of Configuration Word 1 are set
to ‘01’, the BOR is controlled by the SBOREN bit of the
BORCON register. The device start-up is not delayed
by the BOR ready condition or the VDD level.
BOR protection begins as soon as the BOR circuit is
ready. The status of the BOR circuit is reflected in the
BORRDY bit of the BORCON register.
BOR protection is unchanged by Sleep.
BOREN<1:0> SBOREN Device Mode BOR Mode Device
Operation upo n
release of POR
Device
Operation upo n
wake- up from
Sleep
11 X X Active Waits for BOR ready(1)
10 X Awake Active Waits for BOR ready
Sleep Disabled
01 1XActive Begins immediately
0Disabled Begins immediately
00 X X Disabled Begins immediately
Note 1: Even though this case specifically waits for the BOR, the BOR is already operating, so there is no delay in
start-up.
2008-2011 Microchip Technology Inc. DS41364E-page 87
PIC16(L)F1934/6/7
FIGURE 6-2: BROWN-OUT SITUATIONS
REGISTER 6-1: BORCON: BROWN-OUT RESET CONTROL REGISTER
R/W-1/u U-0 U-0 U-0 U-0 U-0 U-0 R-q/u
SBOREN —BORRDY
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition
bit 7 SBOREN: Software Brown-out Reset Enable bit
If BOREN <1:0> in Configuration Word 1 01:
SBOREN is read/write, but has no effect on the BOR.
If BOREN <1:0> in Configuration Word 1 = 01:
1 = BOR Enabled
0 = BOR Disabled
bit 6-1 Unimplemented: Read as ‘0
bit 0 BORRDY: Brown-out Reset Circuit Ready Status bit
1 = The Brown-out Reset circuit is active
0 = The Brown-out Reset circuit is inactive
TPWRT(1)
VBOR
VDD
Internal
Reset
VBOR
VDD
Internal
Reset TPWRT(1)
< TPWRT
TPWRT(1)
VBOR
VDD
Internal
Reset
Note 1: TPWRT delay only if PWRTE bit is programmed to ‘0’.
PIC16(L)F1934/6/7
DS41364E-page 88 2008-2011 Microchip Technology Inc.
6.3 MCLR
The MCLR is an optional external input that can reset
the device. The MCLR function is controlled by the
MCLRE bit of Configuration Word 1 and the LVP bit of
Configuration Word 2 (Ta bl e 6-2).
6.3.1 MCLR ENABLED
When MCLR is enabled and the pin is held low, the
device is held in Reset. The MCLR pin is connected to
VDD through an internal weak pull-up.
The device has a noise filter in the MCLR Reset path.
The filter will detect and ignore small pulses.
6.3.2 MCLR DISABLED
When MCLR is disabled, the pin functions as a general
purpose input and the internal weak pull-up is under
software control. See Section 12.6 “PORTE
Registers” for more information.
6.4 W atchdog Timer (WDT) Reset
The Watchdog Timer generates a Reset if the firmware
does not issue a CLRWDT instruction within the time-out
period. The TO and PD bits in the STATUS register are
changed to indicate the WDT Reset. See Section 10.0
“Watchdog Timer” for more information.
6.5 RESET Instruction
A RESET instruction will cause a device Reset. The RI
bit in the PCON register will be set to ‘0’. See Ta b le 6 - 4
for default conditions after a RESET instruction has
occurred.
6.6 Stack Overflow/Under fl ow Reset
The device can reset when the Stack Overflows or
Underflows. The STKOVF or STKUNF bits of the PCON
register indicate the Reset condition. These Resets are
enabled by setting the STVREN bit in Configuration Word
2. See Section 3.4.2 “Overflow/Underflow Reset” for
more information.
6.7 Programming Mode Exit
Upon exit of Programming mode, the device will
behave as if a POR had just occurred.
6.8 Power-Up Timer
The Power-up Timer optionally delays device execution
after a BOR or POR event. This timer is typically used to
allow VDD to stabilize before allowing the device to start
running.
The Power-up Timer is controlled by the PWRTE bit of
Configuration Word 1.
6.9 Start-up Sequence
Upon the release of a POR or BOR, the following must
occur before the device will begin executing:
1. Power-up Timer runs to completion (if enabled).
2. Oscillator start-up timer runs to completion (if
required for oscillator source).
3. MCLR must be released (if enabled).
The total time-out will vary based on oscillator configu-
ration and Power-up Timer configuration. See
Section 5.0 “Oscillator Module (With Fail-Safe
Clock Monitor)” for more information.
The Power-up Timer and oscillator start-up timer run
independently of MCLR Reset. If MCLR is kept low long
enough, the Power-up Timer and oscillator start-up
timer will expire. Upon bringing MCLR high, the device
will begin execution immediately (see Figure 6-3). This
is useful for testing purposes or to synchronize more
than one device operating in parallel.
TABLE 6-2: MCLR CONFIGURATION
MCLRE LVP MCLR
00Disabled
10Enabled
x1Enabled
Note: A Reset does not drive the MCLR pin low.
2008-2011 Microchip Technology Inc. DS41364E-page 89
PIC16(L)F1934/6/7
FIGURE 6-3: RESET START-UP SEQUENCE
TOST
TMCLR
TPWRT
VDD
Internal POR
Power-Up Timer
MCLR
Internal RESET
Oscillator Modes
Oscillator Start-Up Timer
Oscillator
FOSC
Internal Oscillator
Oscillator
FOSC
External Clock (EC)
CLKIN
FOSC
External Crystal
PIC16(L)F1934/6/7
DS41364E-page 90 2008-2011 Microchip Technology Inc.
6.10 Determining the Cause of a Reset
Upon any Reset, multiple bits in the STATUS and
PCON register are updated to indicate the cause of the
Reset. Ta bl e 6- 3 and Ta bl e 6 -4 show the Reset condi-
tions of these registers.
TABLE 6-3: RESET STATUS BITS AND THEIR SIGNIFICANCE
TABLE 6-4: RESET CONDITION FOR SPECIAL REGISTERS(2)
STKOVF STKUNF RMCLR RI POR BOR TO PD Condition
00110x11Power-on Reset
00110x0xIllegal, TO is set on POR
00110xx0Illegal, PD is set on POR
0011u011Brown-out Reset
uuuuuu0uWDT Reset
uuuuuu00WDT Wake-up from Sleep
uuuuuu10Interrupt Wake-up from Sleep
uu0uuuuuMCLR Reset during normal operation
uu0uuu10MCLR Reset during Sleep
u u u 0 u u u u RESET Instruction Executed
1uuuuuuuStack Overflow Reset (STVREN = 1)
u1uuuuuuStack Underflow Reset (STVREN = 1)
Condition Program
Counter STATUS
Register PCON
Register
Power-on Reset 0000h ---1 1000 00-- 110x
MCLR Reset during normal operation 0000h ---u uuuu uu-- 0uuu
MCLR Reset during Sleep 0000h ---1 0uuu uu-- 0uuu
WDT Reset 0000h ---0 uuuu uu-- uuuu
WDT Wake-up from Sleep PC + 1 ---0 0uuu uu-- uuuu
Brown-out Reset 0000h ---1 1uuu 00-- 11u0
Interrupt Wake-up from Sleep PC + 1(1) ---1 0uuu uu-- uuuu
RESET Instruction Executed 0000h ---u uuuu uu-- u0uu
Stack Overflow Reset (STVREN = 1) 0000h ---u uuuu 1u-- uuuu
Stack Underflow Reset (STVREN = 1) 0000h ---u uuuu u1-- uuuu
Legend: u = unchanged, x = unknown, - = unimplemented bit, reads as ‘0’.
Note1: When the wake-up is due to an interrupt and Global Enable bit (GIE) is set, the return address is pushed on
the stack and PC is loaded with the interrupt vector (0004h) after execution of PC + 1.
2: If a Status bit is not implemented, that bit will be read as 0’.
2008-2011 Microchip Technology Inc. DS41364E-page 91
PIC16(L)F1934/6/7
6.11 Power Control (PCON) Register
The Power Control (PCON) register contains flag bits
to differentiate between a:
Power-on Reset (POR)
Brown-out Reset (BOR)
Reset Instruction Reset (RI)
Stack Overflow Reset (STKOVF)
Stack Underflow Reset (STKUNF)
•MCLR
Reset (RMCLR)
The PCON register bits are shown in Register 6-2.
REGISTER 6-2: PCON: POWER CONTROL REGISTER
R/W/HS-0/q R/W/HS-0/q U-0 U-0 R/W/HC-1/q R/W/HC-1/q R/W/HC-q/u R/W/HC-q/u
STKOVF STKUNF RMCLR RI POR BOR
bit 7 bit 0
Legend:
HC = Bit is cleared by hardware HS = Bit is set by hardware
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -m/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition
bit 7 STKOVF: Stack Overflow Flag bit
1 = A Stack Overflow occurred
0 = A Stack Overflow has not occurred or set to0’ by firmware
bit 6 STKUNF: Stack Underflow Flag bit
1 = A Stack Underflow occurred
0 = A Stack Underflow has not occurred or set to ‘0’ by firmware
bit 5-4 Unimplemented: Read as ‘0
bit 3 RMCLR: MCLR Reset Flag bit
1 = A MCLR Reset has not occurred or set to ‘1 by firmware
0 = A MCLR Reset has occurred (set to ‘0’ in hardware when a MCLR Reset occurs)
bit 2 RI: RESET Instruction Flag bit
1 = A RESET instruction has not been executed or set to1’ by firmware
0 = A RESET instruction has been executed (set to ‘0’ in hardware upon executing a RESET instruction)
bit 1 POR: Power-on Reset Status bit
1 = No Power-on Reset occurred
0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs)
bit 0 BOR: Brown-out Reset Status bit
1 = No Brown-out Reset occurred
0 = A Brown-out Reset occurred (must be set in software after a Power-on Reset or Brown-out Reset
occurs)
PIC16(L)F1934/6/7
DS41364E-page 92 2008-2011 Microchip Technology Inc.
TABLE 6-5: SUMMARY OF REGISTERS ASSOCIATED WITH RESETS
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BORCON SBOREN ————— BORRDY 87
PCON STKOVF STKUNF —RMCLRRI POR BOR 91
STATUS —TOPD ZDC C29
WDTCON WDTPS<4:0> SWDTEN 113
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by Resets.
Note 1: Other (non Power-up) Resets include MCLR Reset and Watchdog Timer Reset during normal operation.
2008-2011 Microchip Technology Inc. DS41364E-page 93
PIC16(L)F1934/6/7
7.0 INTERRUPTS
The interrupt feature allows certain events to preempt
normal program flow. Firmware is used to determine
the source of the interrupt and act accordingly. Some
interrupts can be configured to wake the MCU from
Sleep mode.
This chapter contains the following information for
Interrupts:
Operation
Interrupt Latency
Interrupts During Sleep
•INT Pin
Automatic Context Saving
Many peripherals produce Interrupts. Refer to the cor-
responding chapters for details.
A block diagram of the interrupt logic is shown in
Figure 7-1.
FIGURE 7-1: INTERRUP T LOGIC
D
CK
R
Q
D
CK
R
Q
RBx
IOCBNx
IOCBPx
Q2
D
CK
SQ
Q4Q1
Data Bus =
0 or 1
Write IOCBFx
IOCIE
To Data Bus
IOCBFx
Edge
Detect
IOC Interrupt
to CPU Core
From all other
IOCBFx individual
Pin Detectors
Q1
Q2
Q3
Q4
Q4Q1
Q1
Q2
Q3
Q4
Q1
Q2
Q3
Q4
Q4
Q4Q1 Q4Q1 Q4Q1
PIC16(L)F1934/6/7
DS41364E-page 94 2008-2011 Microchip Technology Inc.
7.1 Operation
Interrupts are disabled upon any device Reset. They
are enabled by setting the following bits:
GIE bit of the INTCON register
Interrupt Enable bit(s) for the specific interrupt
event(s)
PEIE bit of the INTCON register (if the Interrupt
Enable bit of the interrupt event is contained in the
PIE1, PIE2 and PIE3 registers)
The INTCON, PIR1, PIR2 and PIR3 registers record
individual interrupts via interrupt flag bits. Interrupt flag
bits will be set, regardless of the status of the GIE, PEIE
and individual interrupt enable bits.
The following events happen when an interrupt event
occurs while the GIE bit is set:
Current prefetched instruction is flushed
GIE bit is cleared
Current Program Counter (PC) is pushed onto the
stack
Critical registers are automatically saved to the
shadow registers (See Section 7.5 “Automatic
Context Savi ng”)
PC is loaded with the interrupt vector 0004h
The firmware within the Interrupt Service Routine (ISR)
should determine the source of the interrupt by polling
the interrupt flag bits. The interrupt flag bits must be
cleared before exiting the ISR to avoid repeated
interrupts. Because the GIE bit is cleared, any interrupt
that occurs while executing the ISR will be recorded
through its interrupt flag, but will not cause the
processor to redirect to the interrupt vector.
The RETFIE instruction exits the ISR by popping the
previous address from the stack, restoring the saved
context from the shadow registers and setting the GIE
bit.
For additional information on a specific interrupt’s
operation, refer to its peripheral chapter.
7.2 Interrupt Latency
Interrupt latency is defined as the time from when the
interrupt event occurs to the time code execution at the
interrupt vector begins. The latency for synchronous
interrupts is 3 or 4 instruction cycles. For asynchronous
interrupts, the latency is 3 to 5 instruction cycles,
depending on when the interrupt occurs. See Figure 7-2
and Figure 7-3 for more details.
Note 1: Individual interrupt flag bits are set,
regardless of the state of any other
enable bits.
2: All interrupts will be ignored while the GIE
bit is cleared. Any interrupt occurring
while the GIE bit is clear will be serviced
when the GIE bit is set again.
2008-2011 Microchip Technology Inc. DS41364E-page 95
PIC16(L)F1934/6/7
FIGURE 7-2: INTERRUP T LATENCY
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1
CLKOUT
PC 0004h 0005h
PC
Inst(0004h)NOP
GIE
Q1 Q2 Q3 Q4Q1 Q2 Q3 Q4
1 Cycle Instruction at PC
PC
Inst(0004h)NOP
2 Cycle Instruction at PC
FSR ADDR PC+1 PC+2 0004h 0005h
PC
Inst(0004h)NOP
GIE
PCPC-1
3 Cycle Instruction at PC
Execute
Interrupt
Inst(PC)
Interrupt Sampled
during Q1
Inst(PC)
PC-1 PC+1
NOP
PC New PC/
PC+1 0005hPC-1 PC+1/FSR
ADDR 0004h
NOP
Interrupt
GIE
Interrupt
INST(PC) NOPNOP
FSR ADDR PC+1 PC+2 0004h 0005h
PC
Inst(0004h)NOP
GIE
PCPC-1
3 Cycle Instruction at PC
Interrupt
INST(PC) NOPNOP NOP
Inst(0005h)
Execute
Execute
Execute
PIC16(L)F1934/6/7
DS41364E-page 96 2008-2011 Microchip Technology Inc.
FIGURE 7-3: INT PIN INTERRUPT TIMING
Q2Q1 Q3 Q4 Q2Q1 Q3 Q4 Q2Q1 Q3 Q4 Q2Q1 Q3 Q4 Q2Q1 Q3 Q4
OSC1
CLKOUT
INT pin
INTF
GIE
INSTRUCTION FLOW
PC
Instruction
Fetched
Instruction
Executed
Interrupt Latency
PC PC + 1 PC + 1 0004h 0005h
Inst (0004h) Inst (0005h)
Dummy Cycle
Inst (PC) Inst (PC + 1)
Inst (PC – 1) Inst (0004h)
Dummy Cycle
Inst (PC)
Note 1: INTF flag is sampled here (every Q1).
2: Asynchronous interrupt latency = 3-5 TCY. Synchronous latency = 3-4 TCY, where TCY = instruction cycle time.
Latency is the same whether Inst (PC) is a single cycle or a 2-cycle instruction.
3: CLKOUT not available in all Oscillator modes.
4: For minimum width of INT pulse, refer to AC specifications in the applicable Electrical Specifications Chapter.
5: INTF is enabled to be set any time during the Q4-Q1 cycles.
(1) (2)
(3) (4)
(5)
(1)
2008-2011 Microchip Technology Inc. DS41364E-page 97
PIC16(L)F1934/6/7
7.3 Interrupts During Sleep
Some interrupts can be used to wake from Sleep. To
wake from Sleep, the peripheral must be able to
operate without the system clock. The interrupt source
must have the appropriate Interrupt Enable bit(s) set
prior to entering Sleep.
On waking from Sleep, if the GIE bit is also set, the
processor will branch to the interrupt vector. Otherwise,
the processor will continue executing instructions after
the SLEEP instruction. The instruction directly after the
SLEEP instruction will always be executed before
branching to the ISR. Refer to Section 9.0 “Power-
Down Mode (Sleep)” for more details.
7.4 INT Pin
The INT pin can be used to generate an asynchronous
edge-triggered interrupt. This interrupt is enabled by
setting the INTE bit of the INTCON register. The
INTEDG bit of the OPTION_REG register determines on
which edge the interrupt will occur. When the INTEDG
bit is set, the rising edge will cause the interrupt. When
the INTEDG bit is clear, the falling edge will cause the
interrupt. The INTF bit of the INTCON register will be set
when a valid edge appears on the INT pin. If the GIE and
INTE bits are also set, the processor will redirect
program execution to the interrupt vector.
7.5 Automatic Context Saving
Upon entering an interrupt, the return PC address is
saved on the stack. Additionally, the following registers
are automatically saved in the Shadow registers:
W register
STATUS register (except for TO and PD)
BSR register
FSR registers
PCLATH register
Upon exiting the Interrupt Service Routine, these regis-
ters are automatically restored. Any modifications to
these registers during the ISR will be lost. If modifica-
tions to any of these registers are desired, the corre-
sponding Shadow register should be modified and the
value will be restored when exiting the ISR. The
Shadow registers are available in Bank 31 and are
readable and writable. Depending on the user’s appli-
cation, other registers may also need to be saved.
PIC16(L)F1934/6/7
DS41364E-page 98 2008-2011 Microchip Technology Inc.
7.6 Interrupt Control Registers
7.6.1 INTCON REGISTER
The INTCON register is a readable and writable
register, which contains the various enable and flag bits
for TMR0 register overflow, interrupt-on-change and
external INT pin interrupts.
Note: Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the appropri-
ate interrupt flag bits are clear prior to
enabling an interrupt.
REGISTER 7-1: INTCON: INTERRUPT CONTROL REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R-0/0
GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 GIE: Global Interrupt Enable bit
1 = Enables all active interrupts
0 = Disables all interrupts
bit 6 PEIE: Peripheral Interrupt Enable bit
1 = Enables all active peripheral interrupts
0 = Disables all peripheral interrupts
bit 5 TMR0IE: Timer0 Overflow Interrupt Enable bit
1 = Enables the Timer0 interrupt
0 = Disables the Timer0 interrupt
bit 4 INTE: INT External Interrupt Enable bit
1 = Enables the INT external interrupt
0 = Disables the INT external interrupt
bit 3 IOCIE: Interrupt-on-Change Enable bit
1 = Enables the interrupt-on-change
0 = Disables the interrupt-on-change
bit 2 TMR0IF: Timer0 Overflow Interrupt Flag bit
1 = TMR0 register has overflowed
0 = TMR0 register did not overflow
bit 1 INTF: INT External Interrupt Flag bit
1 = The INT external interrupt occurred
0 = The INT external interrupt did not occur
bit 0 IOCIF: Interrupt-on-Change Interrupt Flag bit
1 = When at least one of the interrupt-on-change pins changed state
0 = None of the interrupt-on-change pins have changed state
Note 1: The IOCIF Flag bit is read-only and cleared when all the Interrupt-on-Change flags in the IOCBF register
have been cleared by software.
2008-2011 Microchip Technology Inc. DS41364E-page 99
PIC16(L)F1934/6/7
7.6.2 PIE1 REGISTER
The PIE1 register contains the interrupt enable bits, as
shown in Register 7-2.
Note: Bit PEIE of the INTCON register must be
set to enable any peripheral interrupt.
REGISTER 7-2: PIE1: PERIPHERAL INTERRUPT ENABLE REGISTER 1
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 TMR1GIE: Timer1 Gate Interrupt Enable bit
1 = Enables the Timer1 Gate Acquisition interrupt
0 = Disables the Timer1 Gate Acquisition interrupt
bit 6 ADIE: A/D Converter (ADC) Interrupt Enable bit
1 = Enables the ADC interrupt
0 = Disables the ADC interrupt
bit 5 RCIE: USART Receive Interrupt Enable bit
1 = Enables the USART receive interrupt
0 = Disables the USART receive interrupt
bit 4 TXIE: USART Transmit Interrupt Enable bit
1 = Enables the USART transmit interrupt
0 = Disables the USART transmit interrupt
bit 3 SSPIE: Synchronous Serial Port (MSSP) Interrupt Enable bit
1 = Enables the MSSP interrupt
0 = Disables the MSSP interrupt
bit 2 CCP1IE: CCP1 Interrupt Enable bit
1 = Enables the CCP1 interrupt
0 = Disables the CCP1 interrupt
bit 1 TMR2IE: TMR2 to PR2 Match Interrupt Enable bit
1 = Enables the Timer2 to PR2 match interrupt
0 = Disables the Timer2 to PR2 match interrupt
bit 0 TMR1IE: Timer1 Overflow Interrupt Enable bit
1 = Enables the Timer1 overflow interrupt
0 = Disables the Timer1 overflow interrupt
PIC16(L)F1934/6/7
DS41364E-page 100 2008-2011 Microchip Technology Inc.
7.6.3 PIE2 REGISTER
The PIE2 register contains the interrupt enable bits, as
shown in Register 7-3.
Note: Bit PEIE of the INTCON register must be
set to enable any peripheral interrupt.
REGISTER 7-3: PIE2: PERIPHERAL INTERRUPT ENABLE REGISTER 2
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0
OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 OSFIE: Oscillator Fail Interrupt Enable bit
1 = Enables the Oscillator Fail interrupt
0 = Disables the Oscillator Fail interrupt
bit 6 C2IE: Comparator C2 Interrupt Enable bit
1 = Enables the Comparator C2 interrupt
0 = Disables the Comparator C2 interrupt
bit 5 C1IE: Comparator C1 Interrupt Enable bit
1 = Enables the Comparator C1 interrupt
0 = Disables the Comparator C1 interrupt
bit 4 EEIE: EEPROM Write Completion Interrupt Enable bit
1 = Enables the EEPROM Write Completion interrupt
0 = Disables the EEPROM Write Completion interrupt
bit 3 BCLIE: MSSP Bus Collision Interrupt Enable bit
1 = Enables the MSSP Bus Collision Interrupt
0 = Disables the MSSP Bus Collision Interrupt
bit 2 LCDIE: LCD Module Interrupt Enable bit
1 = Enables the LCD module interrupt
0 = Disables the LCD module interrupt
bit 1 Unimplemented: Read as ‘0
bit 0 CCP2IE: CCP2 Interrupt Enable bit
1 = Enables the CCP2 interrupt
0 = Disables the CCP2 interrupt
2008-2011 Microchip Technology Inc. DS41364E-page 101
PIC16(L)F1934/6/7
7.6.4 PIE3 REGISTER
The PIE3 register contains the interrupt enable bits, as
shown in Register 7-4.
Note: Bit PEIE of the INTCON register must be
set to enable any peripheral interrupt.
REGISTER 7-4: PIE3: PERIPHERAL INTERRUPT ENABLE REGISTER 3
U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 U-0
CCP5IE CCP4IE CCP3IE TMR6IE —TMR4IE
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 Unimplemented: Read as ‘0
bit 6 CCP5IE: CCP5 Interrupt Enable bit
1 = Enables the CCP5 interrupt
0 = Disables the CCP5 interrupt
bit 5 CCP4IE: CCP4 Interrupt Enable bit
1 = Enables the CCP4 interrupt
0 = Disables the CCP4 interrupt
bit 4 CCP3IE: CCP3 Interrupt Enable bit
1 = Enables the CCP3 interrupt
0 = Disables the CCP3 interrupt
bit 3 TMR6IE: TMR6 to PR6 Match Interrupt Enable bit
1 = Enables the TMR6 to PR6 Match interrupt
0 = Disables the TMR6 to PR6 Match interrupt
bit 2 Unimplemented: Read as ‘0
bit 1 TMR4IE: TMR4 to PR4 Match Interrupt Enable bit
1 = Enables the TMR4 to PR4 Match interrupt
0 = Disables the TMR4 to PR4 Match interrupt
bit 0 Unimplemented: Read as ‘0
PIC16(L)F1934/6/7
DS41364E-page 102 2008-2011 Microchip Technology Inc.
7.6.5 PIR1 REGISTER
The PIR1 register contains the interrupt flag bits, as
shown in Register 7-5.
Note: Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear prior
to enabling an interrupt.
REGISTER 7-5: PIR1: PERIPHERAL INTERRUPT REQUEST REGISTER 1
R/W-0/0 R/W-0/0 R-0/0 R-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 TMR1GIF: Timer1 Gate Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 6 ADIF: A/D Converter Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 5 RCIF: USART Receive Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 4 TXIF: USART Transmit Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 3 SSPIF: Synchronous Serial Port (MSSP) Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 2 CCP1IF: CCP1 Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 1 TMR2IF: Timer2 to PR2 Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 0 TMR1IF: Timer1 Overflow Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
2008-2011 Microchip Technology Inc. DS41364E-page 103
PIC16(L)F1934/6/7
7.6.6 PIR2 REGISTER
The PIR2 register contains the interrupt flag bits, as
shown in Register 7-6.
Note: Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear prior
to enabling an interrupt.
REGISTER 7-6: PIR2: PERIPHERAL INTERRUPT REQUEST REGISTER 2
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0
OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 OSFIF: Oscillator Fail Interrupt Flag
1 = Interrupt is pending
0 = Interrupt is not pending
bit 6 C2IF: Comparator C2 Interrupt Flag
1 = Interrupt is pending
0 = Interrupt is not pending
bit 5 C1IF: Comparator C1 Interrupt Flag
1 = Interrupt is pending
0 = Interrupt is not pending
bit 4 EEIF: EEPROM Write Completion Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 3 BCLIF: MSSP Bus Collision Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 2 LCDIF: LCD Module Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 1 Unimplemented: Read as ‘0
bit 0 CCP2IF: CCP2 Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
PIC16(L)F1934/6/7
DS41364E-page 104 2008-2011 Microchip Technology Inc.
7.6.7 PIR3 REGISTER
The PIR3 register contains the interrupt flag bits, as
shown in Register 7-7.
Note: Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the Global
Enable bit, GIE, of the INTCON register.
User software should ensure the
appropriate interrupt flag bits are clear prior
to enabling an interrupt.
REGISTER 7-7: PIR3: PERIPHERAL INTERRUPT REQUEST REGISTER 3
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
CCP5IF CCP4IF CCP3IF TMR6IF —TMR4IF
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 Unimplemented: Read as ‘0
bit 6 CCP5IF: CCP5 Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 5 CCP4IF: CCP4 Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 4 CCP3IF: CCP3 Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 3 TMR6IF: TMR6 to PR6 Match Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 2 Unimplemented: Read as ‘0
bit 1 TMR4IF: TMR4 to PR4 Match Interrupt Flag bit
1 = Interrupt is pending
0 = Interrupt is not pending
bit 0 Unimplemented: Read as ‘0
2008-2011 Microchip Technology Inc. DS41364E-page 105
PIC16(L)F1934/6/7
TABLE 7-1: SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPTS
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
OPTION_REG WPUEN INTEDG TMROCS TMROSE PSA PS<2:0> 193
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE —TMR4IE101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF 103
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF —TMR4IF104
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by Interrupts.
PIC16(L)F1934/6/7
DS41364E-page 106 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 107
PIC16(L)F1934/6/7
8.0 LOW DROPOUT (LDO)
VOLTAGE REGULATOR
The PIC16F1934/6/7 has an internal Low Dropout
Regulator (LDO) which provides operation above 3.6V.
The LDO regulates a voltage for the internal device
logic while permitting the VDD and I/O pins to operate
at a higher voltage. There is no user enable/disable
control available for the LDO, it is always active. The
PIC16(L)F1934/6/7 operates at a maximum VDD of
3.6V and does not incorporate an LDO.
A device I/O pin may be configured as the LDO voltage
output, identified as the VCAP pin. Although not
required, an external low-ESR capacitor may be con-
nected to the VCAP pin for additional regulator stability.
The VCAPEN<1:0> bits of Configuration Word 2 deter-
mines which pin is assigned as the VCAP pin. Refer to
Table 8-1.
On power-up, the external capacitor will load the LDO
voltage regulator. To prevent erroneous operation, the
device is held in Reset while a constant current source
charges the external capacitor. After the cap is fully
charged, the device is released from Reset. For more
information on recommended capacitor values and the
constant current rate, refer to the LDO Regulator
Characteristics Table in the applicable Electrical
Specifications Chapter.
TABLE 8-2: SUMMARY OF CONFIGURATION WORD WITH LDO
TABLE 8-1: VCAPEN<1:0> SELECT BITS
VCAPEN<1:0> Pin
00 RA0
01 RA5
10 RA6
11 No Vcap
Name Bits Bit -/7 Bi t -/6 Bit 13/5 Bi t 12/4 Bit 11/3 Bit 10/2 B it 9/1 B it 8/0 Register
on Page
CONFIG2 13:8 LVP DEBUG BORV STVREN PLLEN 64
7:0 VCAPEN1(1) VCAPEN0(1) WRT1 WRT0
Legend: — = unimplemented locations read as0’. Shaded cells are not used by LDO.
Note 1: PIC16F1934/6/7 only.
PIC16(L)F1934/6/7
DS41364E-page 108 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 109
PIC16(L)F1934/6/7
9.0 POWER-DOWN MODE (SLEEP)
The Power-down mode is entered by executing a
SLEEP instruction.
Upon entering Sleep mode, the following conditions
exist:
1. WDT will be cleared but keeps running, if
enabled for operation during Sleep.
2. PD bit of the STATUS register is cleared.
3. TO bit of the STATUS register is set.
4. CPU clock is disabled.
5. 31 kHz LFINTOSC is unaffected and peripherals
that operate from it may continue operation in
Sleep.
6. Timer1 oscillator is unaffected and peripherals
that operate from it may continue operation in
Sleep.
7. ADC is unaffected, if the dedicated FRC clock is
selected.
8. Capacitive Sensing oscillator is unaffected.
9. I/O ports maintain the status they had before
SLEEP was executed (driving high, low or high-
impedance).
10. Resets other than WDT are not affected by
Sleep mode.
Refer to individual chapters for more details on
peripheral operation during Sleep.
To minimize current consumption, the following condi-
tions should be considered:
I/O pins should not be floating
External circuitry sinking current from I/O pins
Internal circuitry sourcing current from I/O pins
Current draw from pins with internal weak pull-ups
Modules using 31 kHz LFINTOSC
Modules using Timer1 oscillator
I/O pins that are high-impedance inputs should be
pulled to VDD or VSS externally to avoid switching cur-
rents caused by floating inputs.
Examples of internal circuitry that might be sourcing
current include modules such as the DAC and FVR
modules. See Section 17.0 “Digital-to-Analog Con-
verter (DAC) Module” and Section 14.0 “Fixed Volt-
age R eferen ce (FV R)” for more information on these
modules.
9.1 W ake-up from Sleep
The device can wake-up from Sleep through one of the
following events:
1. External Reset input on MCLR pin, if enabled
2. BOR Reset, if enabled
3. POR Reset
4. Watchdog Timer, if enabled
5. Any external interrupt
6. Interrupts by peripherals capable of running dur-
ing Sleep (see individual peripheral for more
information)
The first three events will cause a device Reset. The
last three events are considered a continuation of pro-
gram execution. To determine whether a device Reset
or wake-up event occurred, refer to Section 6.10
“Determining the Cause of a Reset”.
When the SLEEP instruction is being executed, the next
instruction (PC + 1) is prefetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be enabled. Wake-up will
occur regardless of the state of the GIE bit. If the GIE
bit is disabled, the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
enabled, the device executes the instruction after the
SLEEP instruction, the device will call the Interrupt Ser-
vice Routine. In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOP after the SLEEP instruction.
The WDT is cleared when the device wakes up from
Sleep, regardless of the source of wake-up.
PIC16(L)F1934/6/7
DS41364E-page 110 2008-2011 Microchip Technology Inc.
9.1.1 WAKE-UP USING INTERRUPTS
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
If the interrupt occurs before the execution of a
SLEEP instruction
-SLEEP instruction will execute as a NOP.
- WDT and WDT prescaler will not be cleared
-TO
bit of the STATUS register will not be set
-PD
bit of the STATUS register will not be
cleared.
If the interrupt occurs during or after the execu-
tion of a SLEEP instruction
-SLEEP instruction will be completely exe-
cuted
- Device will immediately wake-up from Sleep
- WDT and WDT prescaler will be cleared
-TO
bit of the STATUS register will be set
-PD bit of the STATUS register will be cleared.
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
FIGURE 9-1: WAKE-UP FROM SLEEP THROUGH INTERRUPT
TABLE 9-1: SUMMARY OF REGISTERS ASSOCIATED WITH POWER-DOWN MODE
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
OSC1(1)
CLKOUT(2)
Interrupt flag
GIE bit
(INTCON reg.)
Instruction Flow
PC
Instruction
Fetched
Instruction
Executed
PC PC + 1 PC + 2
Inst(PC) = Sleep
Inst(PC - 1)
Inst(PC + 1)
Sleep
Processor in
Sleep
Interrupt Latency(4)
Inst(PC + 2)
Inst(PC + 1)
Inst(0004h) Inst(0005h)
Inst(0004h)
Dummy Cycle
PC + 2 0004h 0005h
Dummy Cycle
TOST(3)
PC + 2
Note 1: XT, HS or LP Oscillator mode assumed.
2: CLKOUT is not available in XT, HS, or LP Oscillator modes, but shown here for timing reference.
3: TOST = 1024 TOSC (drawing not to scale). This delay applies only to XT, HS or LP Oscillator modes.
4: GIE = 1 assumed. In this case after wake-up, the processor calls the ISR at 0004h. If GIE = 0, execution will continue in-line.
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on
Page
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
IOCBF IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0 152
IOCBN IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0 152
IOCBP IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0 152
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE —TMR4IE101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF 103
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF —TMR4IF104
STATUS —TOPD ZDCC 29
WDTCON WDTPS<4:0> SWDTEN 113
Legend: = unimplemented location, read as 0’. Shaded cells are not used in Power-down mode.
2008-2011 Microchip Technology Inc. DS41364E-page 111
PIC16(L)F1934/6/7
10.0 WATCHDOG TIME R
The Watchdog Timer is a system timer that generates
a Reset if the firmware does not issue a CLRWDT
instruction within the time-out period. The Watchdog
Timer is typically used to recover the system from
unexpected events.
The WDT has the following features:
Independent clock source
Multiple operating modes
- WDT is always on
- WDT is off when in Sleep
- WDT is controlled by software
- WDT is always off
Configurable time-out period is from 1 ms to 256
seconds (typical)
Multiple Reset conditions
Operation during Sleep
FIGURE 10-1: WATCHDOG TIMER BLOCK DIAGRAM
LFINTOSC 23-bit Programmable
Prescaler WDT WDT Time-out
WDTPS<4:0>
SWDTEN
Sleep
WDTE<1:0> = 11
WDTE<1:0> = 01
WDTE<1:0> = 10
PIC16(L)F1934/6/7
DS41364E-page 112 2008-2011 Microchip Technology Inc.
10.1 Independent Clock Source
The WDT derives its time base from the 31 kHz
LFINTOSC internal oscillator. Time intervals in this
chapter are based on a nominal interval of 1 ms. See
the Electrical Specifications Chapters for the
LFINTOSC tolerances.
10.2 WDT Operating Modes
The Watchdog Timer module has four operating modes
controlled by the WDTE<1:0> bits in Configuration
Word 1. See Table 10-1.
10.2.1 WDT IS ALWAYS ON
When the WDTE bits of Configuration Word 1 are set to
11’, the WDT is always on.
WDT protection is active during Sleep.
10.2.2 WDT IS OFF IN SLEEP
When the WDTE bits of Configuration Word 1 are set to
10’, the WDT is on, except in Sleep.
WDT protection is not active during Sleep.
10.2.3 WDT CONTROLLED BY SOFTWARE
When the WDTE bits of Configuration Word 1 are set to
01’, the WDT is controlled by the SWDTEN bit of the
WDTCON register.
WDT protection is unchanged by Sleep. See
Table 10-1 for more details.
TABLE 10-1: WDT OPERATING MODES
10.3 Time-Out Period
The WDTPS bits of the WDTCON register set the
time-out period from 1 ms to 256 seconds (nominal).
After a Reset, the default time-out period is 2 seconds.
10.4 Clearing the WDT
The WDT is cleared when any of the following condi-
tions occur:
•Any Reset
CLRWDT instruction is executed
Device enters Sleep
Device wakes up from Sleep
Oscillator fail event
WDT is disabled
Oscillator Start-up TImer (OST) is running
See Table 10-2 for more information.
10.5 Operation During Sleep
When the device enters Sleep, the WDT is cleared. If
the WDT is enabled during Sleep, the WDT resumes
counting.
When the device exits Sleep, the WDT is cleared
again. The WDT remains clear until the OST, if
enabled, completes. See Section 5.0 “Oscillator
Module (With Fail-Safe Clock Monitor)” for more
information on the OST.
When a WDT time-out occurs while the device is in
Sleep, no Reset is generated. Instead, the device wakes
up and resumes operation. The TO and PD bits in the
STATUS register are changed to indicate the event. See
Section 3.0 “Memory Organization” and STATUS
register (Register 3-1) for more information.
WDTE<1:0> SWDTEN Device
Mode WDT
Mode
11 X XActive
10 X Awake Active
Sleep Disabled
01 1XActive
0Disabled
00 X X Disabled
TABLE 10-2: WDT CLEARING CONDITIONS
Conditions WDT
WDTE<1:0> = 00
Cleared
WDTE<1:0> = 01 and SWDTEN = 0
WDTE<1:0> = 10 and enter Sleep
CLRWDT Command
Oscillator Fail Detected
Exit Sleep + System Clock = T1OSC, EXTRC, INTOSC, EXTCLK
Exit Sleep + System Clock = XT, HS, LP Cleared until the end of OST
Change INTOSC divider (IRCF bits) Unaffected
2008-2011 Microchip Technology Inc. DS41364E-page 113
PIC16(L)F1934/6/7
10.6 Wat chdog Control Register
REGISTER 10-1: WDTCON: WATCHDOG TIMER CONTROL REGISTER
U-0 U-0 R/W-0/0 R/W-1/1 R/W-0/0 R/W-1/1 R/W-1/1 R/W-0/0
WDTPS<4:0> SWDTEN
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -m/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-6 Unimplemented: Read as ‘0
bit 5-1 WDTPS<4:0>: Watchdog Timer Period Select bits
Bit Value = Prescale Rate
00000 = 1:32 (Interval 1 ms typ)
00001 = 1:64 (Interval 2 ms typ)
00010 = 1:128 (Interval 4 ms typ)
00011 = 1:256 (Interval 8 ms typ)
00100 = 1:512 (Interval 16 ms typ)
00101 = 1:1024 (Interval 32 ms typ)
00110 = 1:2048 (Interval 64 ms typ)
00111 = 1:4096 (Interval 128 ms typ)
01000 = 1:8192 (Interval 256 ms typ)
01001 = 1:16384 (Interval 512 ms typ)
01010 = 1:32768 (Interval 1s typ)
01011 = 1:65536 (Interval 2s typ) (Reset value)
01100 = 1:131072 (217) (Interval 4s typ)
01101 = 1:262144 (218) (Interval 8s typ)
01110 = 1:524288 (219) (Interval 16s typ)
01111 = 1:1048576 (220) (Interval 32s typ)
10000 = 1:2097152 (221) (Interval 64s typ)
10001 = 1:4194304 (222) (Interval 128s typ)
10010 = 1:8388608 (223) (Interval 256s typ)
10011 = Reserved. Results in minimum interval (1:32)
11111 = Reserved. Results in minimum interval (1:32)
bit 0 SWDTEN: Software Enable/Disable for Watchdog Timer bit
If WDTE<1:0> = 00:
This bit is ignored.
If WDTE<1:0> = 01:
1 = WDT is turned on
0 = WDT is turned off
If WDTE<1:0> = 1x:
This bit is ignored.
PIC16(L)F1934/6/7
DS41364E-page 114 2008-2011 Microchip Technology Inc.
TABLE 10-3: SUMMARY OF REGISTERS ASSOCIATED WITH WATCHDOG TIMER
TABLE 10-4: SUMMARY OF CONFIGURATION WORD WITH WATCHDOG TIMER
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
OSCCON SPLLEN IRCF<3:0> —SCS<1:0>
64
STATUS ———TOPD ZDC C29
WDTCON WDTPS<4:0> SWDTEN 113
Legend: x = unknown, u = unchanged, – = unimplemented locations read as 0’. Shaded cells are not used by Watchdog Timer.
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0 Register
on Page
CONFIG1 13:8 FCMEN IESO CLKOUTEN BOREN<1:0> CPD 62
7:0 CP MCLRE PWRTE WDTE<1:0> FOSC<2:0>
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by Watchdog Timer.
2008-2011 Microchip Technology Inc. DS41364E-page 115
PIC16(L)F1934/6/7
11.0 DATA EEPROM AND FLASH
PROGRAM MEMORY
CONTROL
The data EEPROM and Flash program memory are
readable and writable during normal operation (full VDD
range). These memories are not directly mapped in the
register file space. Instead, they are indirectly
addressed through the Special Function Registers
(SFRs). There are six SFRs used to access these
memories:
EECON1
EECON2
EEDATL
•EEDATH
EEADRL
•EEADRH
When interfacing the data memory block, EEDATL
holds the 8-bit data for read/write, and EEADRL holds
the address of the EEDATL location being accessed.
These devices have 256 bytes of data EEPROM with
an address range from 0h to 0FFh.
When accessing the program memory block, the
EEDATH:EEDATL register pair forms a 2-byte word
that holds the 14-bit data for read/write, and the
EEADRL and EEADRH registers form a 2-byte word
that holds the 15-bit address of the program memory
location being read.
The EEPROM data memory allows byte read and write.
An EEPROM byte write automatically erases the loca-
tion and writes the new data (erase before write).
The write time is controlled by an on-chip timer. The
write/erase voltages are generated by an on-chip
charge pump rated to operate over the voltage range of
the device for byte or word operations.
Depending on the setting of the Flash Program
Memory Self Write Enable bits WRT<1:0> of the
Configuration Word 2, the device may or may not be
able to write certain blocks of the program memory.
However, reads from the program memory are always
allowed.
When the device is code-protected, the device
programmer can no longer access data or program
memory. When code-protected, the CPU may continue
to read and write the data EEPROM memory and Flash
program memory.
11.1 EEADRL and EEADRH Registers
The EEADRH:EEADRL register pair can address up to
a maximum of 256 bytes of data EEPROM or up to a
maximum of 32K words of program memory.
When selecting a program address value, the MSB of
the address is written to the EEADRH register and the
LSB is written to the EEADRL register. When selecting
a EEPROM address value, only the LSB of the address
is written to the EEADRL register.
11.1.1 EECON1 AND EECON2 REGISTERS
EECON1 is the control register for EE memory
accesses.
Control bit EEPGD determines if the access will be a
program or data memory access. When clear, any
subsequent operations will operate on the EEPROM
memory. When set, any subsequent operations will
operate on the program memory. On Reset, EEPROM is
selected by default.
Control bits RD and WR initiate read and write,
respectively. These bits cannot be cleared, only set, in
software. They are cleared in hardware at completion
of the read or write operation. The inability to clear the
WR bit in software prevents the accidental, premature
termination of a write operation.
The WREN bit, when set, will allow a write operation to
occur. On power-up, the WREN bit is clear. The
WRERR bit is set when a write operation is interrupted
by a Reset during normal operation. In these situations,
following Reset, the user can check the WRERR bit
and execute the appropriate error handling routine.
Interrupt flag bit EEIF of the PIR2 register is set when
write is complete. It must be cleared in the software.
Reading EECON2 will read all ‘0’s. The EECON2 reg-
ister is used exclusively in the data EEPROM write
sequence. To enable writes, a specific pattern must be
written to EECON2.
PIC16(L)F1934/6/7
DS41364E-page 116 2008-2011 Microchip Technology Inc.
11.2 Using the Data EEPROM
The data EEPROM is a high-endurance, byte address-
able array that has been optimized for the storage of
frequently changing information (e.g., program vari-
ables or other data that are updated often). When vari-
ables in one section change frequently, while variables
in another section do not change, it is possible to
exceed the total number of write cycles to the
EEPROM without exceeding the total number of write
cycles to a single byte. Refer to the applicable Electri-
cal Specifications Chapter. If this is the case, then a
refresh of the array must be performed. For this reason,
variables that change infrequently (such as constants,
IDs, calibration, etc.) should be stored in Flash program
memory.
11.2.1 READING THE DATA EEPROM
MEMORY
To read a data memory location, the user must write the
address to the EEADRL register, clear the EEPGD and
CFGS control bits of the EECON1 register, and then
set control bit RD. The data is available at the very next
cycle, in the EEDATL register; therefore, it can be read
in the next instruction. EEDATL will hold this value until
another read or until it is written to by the user (during
a write operation).
EXAMPLE 11-1: DATA EEPROM READ
11.2.2 WRITING TO THE DATA EEPROM
MEMORY
To write an EEPROM data location, the user must first
write the address to the EEADRL register and the data
to the EEDATL register. Then the user must follow a
specific sequence to initiate the write for each byte.
The write will not initiate if the above sequence is not
followed exactly (write 55h to EECON2, write AAh to
EECON2, then set the WR bit) for each byte. Interrupts
should be disabled during this code segment.
Additionally, the WREN bit in EECON1 must be set to
enable write. This mechanism prevents accidental
writes to data EEPROM due to errant (unexpected)
code execution (i.e., lost programs). The user should
keep the WREN bit clear at all times, except when
updating EEPROM. The WREN bit is not cleared
by hardware.
After a write sequence has been initiated, clearing the
WREN bit will not affect this write cycle. The WR bit will
be inhibited from being set unless the WREN bit is set.
At the completion of the write cycle, the WR bit is
cleared in hardware and the EE Write Complete
Interrupt Flag bit (EEIF) is set. The user can either
enable this interrupt or poll this bit. EEIF must be
cleared by software.
11.2.3 PROTECTION AGAINST SPURIOUS
WRITE
There are conditions when the user may not want to
write to the data EEPROM memory. To protect against
spurious EEPROM writes, various mechanisms have
been built-in. On power-up, WREN is cleared. Also, the
Power-up Timer (64 ms duration) prevents EEPROM
write.
The write initiate sequence and the WREN bit together
help prevent an accidental write during:
Brown-out
Power Glitch
Software Malfunction
11.2.4 DATA EEPROM OPERATION
DURING CODE-PROTECT
Data memory can be code-protected by programming
the CPD bit in the Configuration Word 1 (Register 5-1)
to ‘0’.
When the data memory is code-protected, only the
CPU is able to read and write data to the data
EEPROM. It is recommended to code-protect the pro-
gram memory when code-protecting data memory.
This prevents anyone from replacing your program with
a program that will access the contents of the data
EEPROM.
Note: Data EEPROM can be read regardless of
the setting of the CPD bit.
BANKSEL EEADRL ;
MOVLW DATA_EE_ADDR ;
MOVWF EEADRL ;Data Memory
;Address to read
BCF EECON1, CFGS ;Deselect Config space
BCF EECON1, EEPGD;Point to DATA memory
BSF EECON1, RD ;EE Read
MOVF EEDATL, W ;W = EEDATL
2008-2011 Microchip Technology Inc. DS41364E-page 117
PIC16(L)F1934/6/7
EXAMPLE 11-2: DATA EEPROM WRITE
FIGURE 11 -1: FLASH PROGRAM MEMORY READ CYCLE EXECUTION
BANKSEL EEADRL ;
MOVLW DATA_EE_ADDR ;
MOVWF EEADRL ;Data Memory Address to write
MOVLW DATA_EE_DATA ;
MOVWF EEDATL ;Data Memory Value to write
BCF EECON1, CFGS ;Deselect Configuration space
BCF EECON1, EEPGD ;Point to DATA memory
BSF EECON1, WREN ;Enable writes
BCF INTCON, GIE ;Disable INTs.
MOVLW 55h ;
MOVWF EECON2 ;Write 55h
MOVLW 0AAh ;
MOVWF EECON2 ;Write AAh
BSF EECON1, WR ;Set WR bit to begin write
BSF INTCON, GIE ;Enable Interrupts
BCF EECON1, WREN ;Disable writes
BTFSC EECON1, WR ;Wait for write to complete
GOTO $-2 ;Done
Required
Sequence
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
BSF EECON1,RD
executed here INSTR(PC + 1)
executed here Forced NOP
executed here
PC
PC + 1 EEADRH,EEADRL PC+3 PC + 5
Flash ADDR
RD bit
EEDATH,EEDATL
PC + 3 PC + 4
INSTR (PC + 1)
INSTR(PC - 1)
executed here INSTR(PC + 3)
executed here INSTR(PC + 4)
executed here
Flash Data
EEDATH
EEDATL
Register
EERHLT
INSTR (PC) INSTR (PC + 3) INSTR (PC + 4)
PIC16(L)F1934/6/7
DS41364E-page 118 2008-2011 Microchip Technology Inc.
11.3 Flash Program Memory Overview
It is important to understand the Flash program mem-
ory structure for erase and programming operations.
Flash Program memory is arranged in rows. A row con-
sists of a fixed number of 14-bit program memory
words. A row is the minimum block size that can be
erased by user software.
Flash program memory may only be written or erased
if the destination address is in a segment of memory
that is not write-protected, as defined in bits WRT<1:0>
of Configuration Word 2.
After a row has been erased, the user can reprogram
all or a portion of this row. Data to be written into the
program memory row is written to 14-bit wide data write
latches. These write latches are not directly accessible
to the user, but may be loaded via sequential writes to
the EEDATH:EEDATL register pair.
The number of data write latches may not be equivalent
to the number of row locations. During programming,
user software may need to fill the set of write latches
and initiate a programming operation multiple times in
order to fully reprogram an erased row. For example, a
device with a row size of 32 words and eight write
latches will need to load the write latches with data and
initiate a programming operation four times.
The size of a program memory row and the number of
program memory write latches may vary by device.
See Table 11-1 for details.
11.3.1 READING THE FLASH PROGRAM
MEMORY
To read a program memory location, the user must:
1. Write the Least and Most Significant address
bits to the EEADRH:EEADRL register pair.
2. Clear the CFGS bit of the EECON1 register.
3. Set the EEPGD control bit of the EECON1
register.
4. Then, set control bit RD of the EECON1 register.
Once the read control bit is set, the program memory
Flash controller will use the second instruction cycle to
read the data. This causes the second instruction
immediately following the “BSF EECON1,RD instruction
to be ignored. The data is available in the very next cycle,
in the EEDATH:EEDATL register pair; therefore, it can
be read as two bytes in the following instructions.
EEDATH:EEDATL register pair will hold this value until
another read or until it is written to by the user.
Note: If the user wants to modify only a portion
of a previously programmed row, then the
contents of the entire row must be read
and saved in RAM prior to the erase.
TABLE 11-1: FLASH MEMORY
ORGANIZATION BY DEVICE
Device Erase Block
(Row) Size/
Boundary
Number of
Write
Latches/
Boundary
PIC16(L)F1934/6/7 32 words,
EEADRL<4:0>
= 00000
8 words,
EEADRL<2:0>
= 000
Note 1: The two instructions following a program
memory read are required to be NOPs.
This prevents the user from executing a
two-cycle instruction on the next
instruction after the RD bit is set.
2: Flash program memory can be read
regardless of the setting of the CP bit.
2008-2011 Microchip Technology Inc. DS41364E-page 119
PIC16(L)F1934/6/7
EXAMPLE 11-3: FLASH PROGRAM MEMORY READ
* This code block will read 1 word of program
* memory at the memory address:
PROG_ADDR_HI: PROG_ADDR_LO
* data will be returned in the variables;
* PROG_DATA_HI, PROG_DATA_LO
BANKSEL EEADRL ; Select Bank for EEPROM registers
MOVLW PROG_ADDR_LO ;
MOVWF EEADRL ; Store LSB of address
MOVLW PROG_ADDR_HI ;
MOVWL EEADRH ; Store MSB of address
BCF EECON1,CFGS ; Do not select Configuration Space
BSF EECON1,EEPGD ; Select Program Memory
BCF INTCON,GIE ; Disable interrupts
BSF EECON1,RD ; Initiate read
NOP ; Executed (Figure 11-1)
NOP ; Ignored (Figure 11-1)
BSF INTCON,GIE ; Restore interrupts
MOVF EEDATL,W ; Get LSB of word
MOVWF PROG_DATA_LO ; Store in user location
MOVF EEDATH,W ; Get MSB of word
MOVWF PROG_DATA_HI ; Store in user location
PIC16(L)F1934/6/7
DS41364E-page 120 2008-2011 Microchip Technology Inc.
11.3.2 ERASING FLASH PROGRAM
MEMORY
While executing code, program memory can only be
erased by rows. To erase a row:
1. Load the EEADRH:EEADRL register pair with
the address of new row to be erased.
2. Clear the CFGS bit of the EECON1 register.
3. Set the EEPGD, FREE, and WREN bits of the
EECON1 register.
4. Write 55h, then AAh, to EECON2 (Flash
programming unlock sequence).
5. Set control bit WR of the EECON1 register to
begin the erase operation.
6. Poll the FREE bit in the EECON1 register to
determine when the row erase has completed.
See Example 11-4.
After theBSF EECON1,WR” instruction, the processor
requires two cycles to set up the erase operation. The
user must place two NOP instructions after the WR bit is
set. The processor will halt internal operations for the
typical 2 ms erase time. This is not Sleep mode as the
clocks and peripherals will continue to run. After the
erase cycle, the processor will resume operation with
the third instruction after the EECON1 write instruction.
11.3.3 WRITING TO FLASH PROGRAM
MEMORY
Program memory is programmed using the following
steps:
1. Load the starting address of the word(s) to be
programmed.
2. Load the write latches with data.
3. Initiate a programming operation.
4. Repeat steps 1 through 3 until all data is written.
Before writing to program memory, the word(s) to be
written must be erased or previously unwritten. Pro-
gram memory can only be erased one row at a time. No
automatic erase occurs upon the initiation of the write.
Program memory can be written one or more words at
a time. The maximum number of words written at one
time is equal to the number of write latches. See
Figure 11-2 (block writes to program memory with 8
write latches) for more details. The write latches are
aligned to the address boundary defined by EEADRL
as shown in Ta bl e 11 - 1 . Write operations do not cross
these boundaries. At the completion of a program
memory write operation, the write latches are reset to
contain 0x3FFF.
The following steps should be completed to load the
write latches and program a block of program memory.
These steps are divided into two parts. First, all write
latches are loaded with data except for the last program
memory location. Then, the last write latch is loaded
and the programming sequence is initiated. A special
unlock sequence is required to load a write latch with
data or initiate a Flash programming operation. This
unlock sequence should not be interrupted.
1. Set the EEPGD and WREN bits of the EECON1
register.
2. Clear the CFGS bit of the EECON1 register.
3. Set the LWLO bit of the EECON1 register. When
the LWLO bit of the EECON1 register is ‘1’, the
write sequence will only load the write latches
and will not initiate the write to Flash program
memory.
4. Load the EEADRH:EEADRL register pair with
the address of the location to be written.
5. Load the EEDATH:EEDATL register pair with
the program memory data to be written.
6. Write 55h, then AAh, to EECON2, then set the
WR bit of the EECON1 register (Flash
programming unlock sequence). The write latch
is now loaded.
7. Increment the EEADRH:EEADRL register pair
to point to the next location.
8. Repeat steps 5 through 7 until all but the last
write latch has been loaded.
9. Clear the LWLO bit of the EECON1 register.
When the LWLO bit of the EECON1 register is
0’, the write sequence will initiate the write to
Flash program memory.
10. Load the EEDATH:EEDATL register pair with
the program memory data to be written.
11. Write 55h, then AAh, to EECON2, then set the
WR bit of the EECON1 register (Flash
programming unlock sequence). The entire
latch block is now written to Flash program
memory.
It is not necessary to load the entire write latch block
with user program data. However, the entire write latch
block will be written to program memory.
An example of the complete write sequence for eight
words is shown in Example 11-5. The initial address is
loaded into the EEADRH:EEADRL register pair; the
eight words of data are loaded using indirect
addressing.
Note: The code sequence provided in
Example 11-5 must be repeated multiple
times to fully program an erased program
memory row.
2008-2011 Microchip Technology Inc. DS41364E-page 121
PIC16(L)F1934/6/7
After theBSF EECON1,WR” instruction, the processor
requires two cycles to set up the write operation. The
user must place two NOP instructions after the WR bit is
set. The processor will halt internal operations for the
typical 2 ms, only during the cycle in which the write
takes place (i.e., the last word of the block write). This
is not Sleep mode as the clocks and peripherals will
continue to run. The processor does not stall when
LWLO = 1, loading the write latches. After the write
cycle, the processor will resume operation with the third
instruction after the EECON1 write instruction.
FIGURE 11-2: BLOCK WRITES TO FLASH PROGRAM MEMORY WITH 8 WRITE LATCHES
14 14 14 14
Program Memory
Buffer Register
EEADRL<2:0> = 000
Buffer Register
EEADRL<2:0> = 001
Buffer Register
EEADRL<2:0> = 010
Buffer Register
EEADRL<2:0> = 111
EEDATA
EEDATH
75 07 0
68
First word of block
to be written Last word of block
to be written
PIC16(L)F1934/6/7
DS41364E-page 122 2008-2011 Microchip Technology Inc.
EXAMPLE 11-4: ERASING ONE ROW OF PROGRAM MEMORY -
; This row erase routine assumes the following:
; 1. A valid address within the erase block is loaded in ADDRH:ADDRL
; 2. ADDRH and ADDRL are located in shared data memory 0x70 - 0x7F (common RAM)
BCF INTCON,GIE ; Disable ints so required sequences will execute properly
BANKSEL EEADRL
MOVF ADDRL,W ; Load lower 8 bits of erase address boundary
MOVWF EEADRL
MOVF ADDRH,W ; Load upper 6 bits of erase address boundary
MOVWF EEADRH
BSF EECON1,EEPGD ; Point to program memory
BCF EECON1,CFGS ; Not configuration space
BSF EECON1,FREE ; Specify an erase operation
BSF EECON1,WREN ; Enable writes
MOVLW 55h ; Start of required sequence to initiate erase
MOVWF EECON2 ; Write 55h
MOVLW 0AAh ;
MOVWF EECON2 ; Write AAh
BSF EECON1,WR ; Set WR bit to begin erase
NOP ; Any instructions here are ignored as processor
; halts to begin erase sequence
NOP ; Processor will stop here and wait for erase complete.
; after erase processor continues with 3rd instruction
BCF EECON1,WREN ; Disable writes
BSF INTCON,GIE ; Enable interrupts
Required
Sequence
2008-2011 Microchip Technology Inc. DS41364E-page 123
PIC16(L)F1934/6/7
EXAMPLE 11-5: WRITING TO FLASH PROGRAM MEMORY
; This write routine assumes the following:
; 1. The 16 bytes of data are loaded, starting at the address in DATA_ADDR
; 2. Each word of data to be written is made up of two adjacent bytes in DATA_ADDR,
; stored in little endian format
; 3. A valid starting address (the least significant bits = 000) is loaded in ADDRH:ADDRL
; 4. ADDRH and ADDRL are located in shared data memory 0x70 - 0x7F (common RAM)
;BCF INTCON,GIE ; Disable ints so required sequences will execute properly
BANKSEL EEADRH ; Bank 3
MOVF ADDRH,W ; Load initial address
MOVWF EEADRH ;
MOVF ADDRL,W ;
MOVWF EEADRL ;
MOVLW LOW DATA_ADDR ; Load initial data address
MOVWF FSR0L ;
MOVLW HIGH DATA_ADDR ; Load initial data address
MOVWF FSR0H ;
BSF EECON1,EEPGD ; Point to program memory
BCF EECON1,CFGS ; Not configuration space
BSF EECON1,WREN ; Enable writes
BSF EECON1,LWLO ; Only Load Write Latches
LOOP MOVIW FSR0++ ; Load first data byte into lower
MOVWF EEDATL ;
MOVIW FSR0++ ; Load second data byte into upper
MOVWF EEDATH ;
MOVF EEADRL,W ; Check if lower bits of address are '000'
XORLW 0x07 ; Check if we're on the last of 8 addresses
ANDLW 0x07 ;
BTFSC STATUS,Z ; Exit if last of eight words,
GOTO START_WRITE ;
MOVLW 55h ; Start of required write sequence:
MOVWF EECON2 ; Write 55h
MOVLW 0AAh ;
MOVWF EECON2 ; Write AAh
BSF EECON1,WR ; Set WR bit to begin write
NOP ; Any instructions here are ignored as processor
; halts to begin write sequence
NOP ; Processor will stop here and wait for write to complete.
; After write processor continues with 3rd instruction.
INCF EEADRL,F ; Still loading latches Increment address
GOTO LOOP ; Write next latches
START_WRITE
BCF EECON1,LWLO ; No more loading latches - Actually start Flash program
; memory write
MOVLW 55h ; Start of required write sequence:
MOVWF EECON2 ; Write 55h
MOVLW 0AAh ;
MOVWF EECON2 ; Write AAh
BSF EECON1,WR ; Set WR bit to begin write
NOP ; Any instructions here are ignored as processor
; halts to begin write sequence
NOP ; Processor will stop here and wait for write complete.
; after write processor continues with 3rd instruction
BCF EECON1,WREN ; Disable writes
BSF INTCON,GIE ; Enable interrupts
Required
Sequence
Required
Sequence
PIC16(L)F1934/6/7
DS41364E-page 124 2008-2011 Microchip Technology Inc.
11.4 Modifying Flash Program Memory
When modifying existing data in a program memory
row, and data within that row must be preserved, it must
first be read and saved in a RAM image. Program
memory is modified using the following steps:
1. Load the starting address of the row to be mod-
ified.
2. Read the existing data from the row into a RAM
image.
3. Modify the RAM image to contain the new data
to be written into program memory.
4. Load the starting address of the row to be rewrit-
ten.
5. Erase the program memory row.
6. Load the write latches with data from the RAM
image.
7. Initiate a programming operation.
8. Repeat steps 6 and 7 as many times as required
to reprogram the erased row.
11.5 User ID, Device ID and
Configurati on Word Access
Instead of accessing program memory or EEPROM
data memory, the User ID’s, Device ID/Revision ID and
Configuration Words can be accessed when CFGS = 1
in the EECON1 register. This is the region that would
be pointed to by PC<15> = 1, but not all addresses are
accessible. Different access may exist for reads and
writes. Refer to Table 11-2.
When read access is initiated on an address outside the
parameters listed in Table 11-2, the EEDATH:EEDATL
register pair is cleared.
TABLE 11-2: USER ID, DEVICE ID AND CONFIGURATION WORD ACCESS (CFGS = 1)
EXAMPLE 11-3: CONFIGURATION WORD AND DEVICE ID ACCESS
Address Function Read Access Write Access
8000h-8003h User IDs Yes Yes
8006h Device ID/Revision ID Yes No
8007h-8008h Configuration Words 1 and 2 Yes No
* This code block will read 1 word of program memory at the memory address:
* PROG_ADDR_LO (must be 00h-08h) data will be returned in the variables;
* PROG_DATA_HI, PROG_DATA_LO
BANKSEL EEADRL ; Select correct Bank
MOVLW PROG_ADDR_LO ;
MOVWF EEADRL ; Store LSB of address
CLRF EEADRH ; Clear MSB of address
BSF EECON1,CFGS ; Select Configuration Space
BCF INTCON,GIE ; Disable interrupts
BSF EECON1,RD ; Initiate read
NOP ; Executed (See Figure 11-1)
NOP ; Ignored (See Figure 11-1)
BSF INTCON,GIE ; Restore interrupts
MOVF EEDATL,W ; Get LSB of word
MOVWF PROG_DATA_LO ; Store in user location
MOVF EEDATH,W ; Get MSB of word
MOVWF PROG_DATA_HI ; Store in user location
2008-2011 Microchip Technology Inc. DS41364E-page 125
PIC16(L)F1934/6/7
11.6 Write Verify
Depending on the application, good programming
practice may dictate that the value written to the data
EEPROM or program memory should be verified (see
Example 11-6) to the desired value to be written.
Example 11-6 shows how to verify a write to EEPROM.
EXAM PLE 11-6: EEPROM WRITE VERIFY
BANKSEL EEDATL ;
MOVF EEDATL, W ;EEDATL not changed
;from previous write
BSF EECON1, RD ;YES, Read the
;value written
XORWF EEDATL, W ;
BTFSS STATUS, Z ;Is data the same
GOTO WRITE_ERR ;No, handle error
: ;Yes, continue
PIC16(L)F1934/6/7
DS41364E-page 126 2008-2011 Microchip Technology Inc.
REGISTER 11-1: EEDATL: EEPROM DATA LOW BYTE REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
EEDAT<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 EEDAT<7:0>: Read/write value for EEPROM data byte or Least Significant bits of program memory
REGISTER 11-2: EEDATH: EEPROM DATA HIGH BYTE REGISTER
U-0 U-0 R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
EEDAT<13:8>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-6 Unimplemented: Read as ‘0
bit 5-0 EEDAT<13:8>: Read/write value for Most Significant bits of program memory
REGISTER 11-3: EEADRL: EEPROM ADDRESS LOW BYTE REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
EEADR<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 EEADR<7:0>: Specifies the Least Significant bits for program memory address or EEPROM address
REGISTER 11-4: EEADRH: EEPROM ADDRESS HIGH BYTE REGISTER
U-1 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
EEADR<14:8>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 Unimplemented: Read as ‘1
bit 6-0 EEADR<14:8>: Specifies the Most Significant bits for program memory address or EEPROM address
2008-2011 Microchip Technology Inc. DS41364E-page 127
PIC16(L)F1934/6/7
REGISTER 11-5: EECON1: EEPROM CONTROL 1 REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W/HC-0/0 R/W-x/q R/W-0/0 R/S/HC-0/0 R/S/HC-0/0
EEPGD CFGS LWLO FREE WRERR WREN WR RD
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
S = Bit can only be set x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware
bit 7 EEPGD: Flash Program/Data EEPROM Memory Select bit
1 = Accesses program space Flash memory
0 = Accesses data EEPROM memory
bit 6 CFGS: Flash Program/Data EEPROM or Configuration Select bit
1 = Accesses Configuration, User ID and Device ID Registers
0 = Accesses Flash Program or data EEPROM Memory
bit 5 LWLO: Load Write Latches Only bit
If CFGS = 1 (Configuration space) OR CFGS = 0 and EEPGD = 1 (program Flash):
1 = The next WR command does not initiate a write; only the program memory latches are
updated.
0 = The next WR command writes a value from EEDATH:EEDATL into program memory latches
and initiates a write of all the data stored in the program memory latches.
If CFGS = 0 and EEPGD = 0: (Accessing data EEPROM)
LWLO is ignored. The next WR command initiates a write to the data EEPROM.
bit 4 FREE: Program Flash Erase Enable bit
If CFGS = 1 (Configuration space) OR CFGS = 0 and EEPGD = 1 (program Flash):
1 = Performs an erase operation on the next WR command (cleared by hardware after comple-
tion of erase).
0 = Performs a write operation on the next WR command.
If EEPGD = 0 and CFGS = 0: (Accessing data EEPROM)
FREE is ignored. The next WR command will initiate both a erase cycle and a write cycle.
bit 3 WRERR: EEPROM Error Flag bit
1 = Condition indicates an improper program or erase sequence attempt or termination (bit is set
automatically on any set attempt (write1’) of the WR bit).
0 = The program or erase operation completed normally.
bit 2 WREN: Program/Erase Enable bit
1 = Allows program/erase cycles
0 = Inhibits programming/erasing of program Flash and data EEPROM
bit 1 WR: Write Control bit
1 = Initiates a program Flash or data EEPROM program/erase operation.
The operation is self-timed and the bit is cleared by hardware once operation is complete.
The WR bit can only be set (not cleared) in software.
0 = Program/erase operation to the Flash or data EEPROM is complete and inactive.
bit 0 RD: Read Control bit
1 = Initiates an program Flash or data EEPROM read. Read takes one cycle. RD is cleared in
hardware. The RD bit can only be set (not cleared) in software.
0 = Does not initiate a program Flash or data EEPROM data read.
PIC16(L)F1934/6/7
DS41364E-page 128 2008-2011 Microchip Technology Inc.
TABLE 11-3: SUMMARY OF REGISTERS ASSOCIATED WITH DATA EEPROM
REGISTER 11-6: EECON2: EEPROM CONTROL 2 REGISTER
W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0 W-0/0
EEPROM Control Register 2
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
S = Bit can only be set x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 Dat a EEPROM Unlock Pattern bit s
To unlock writes, a 55h must be written first, followed by an AAh, before setting the WR bit of the
EECON1 register. The value written to this register is used to unlock the writes. There are specific
timing requirements on these writes. Refer to Section 11.2.2 “Writing to the Data EEPROM
Memory for more information.
Name Bit 7 Bit 6 B it 5 Bit 4 B it 3 Bit 2 Bit 1 B it 0 Register on
Page
EECON1 EEPGD CFGS LWLO FREE WRERR WREN WR RD 127
EECON2 EEPROM Control Register 2 (not a physical register) 115*
EEADRL EEADRL<7:0> 126
EEADRH EEADRH<6:0 126
EEDATL EEDATL<7:0> 126
EEDATH EEDATH<5:0> 126
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF 103
Legend: = unimplemented location, read as ‘0’. Shaded cells are not used by the data EEPROM module.
* Page provides register information.
2008-2011 Microchip Technology Inc. DS41364E-page 129
PIC16(L)F1934/6/7
12.0 I/O PORTS
Depending on the device selected and peripherals
enabled, there are up to five ports available. In general,
when a peripheral is enabled on a port pin, that pin
cannot be used as a general purpose output. However,
the pin can still be read.
Each port has three standard registers for its operation.
These registers are:
TRISx registers (data direction)
PORTx registers (reads the levels on the pins of
the device)
LATx registers (output latch)
Some ports may have one or more of the following
additional registers. These registers are:
ANSELx (analog select)
WPUx (weak pull-up)
INLVLx (input level control)
The Data Latch (LATx registers) is useful for
read-modify-write operations on the value that the I/O
pins are driving.
A write operation to the LATx register has the same
effect as a write to the corresponding PORTx register.
A read of the LATx register reads of the values held in
the I/O PORT latches, while a read of the PORTx
register reads the actual I/O pin value.
Ports that support analog inputs have an associated
ANSELx register. When an ANSEL bit is set, the digital
input buffer associated with that bit is disabled.
Disabling the input buffer prevents analog signal levels
on the pin between a logic high and low from causing
excessive current in the logic input circuitry. A
simplified model of a generic I/O port, without the
interfaces to other peripherals, is shown in Figure 12-1.
FIGURE 12-1: GENERIC I/O PORT
OPERATION
EXAMPLE 12-1: INITIA LIZI NG PORTA
TABLE 12-1: PORT AVAILABILITY PER
DEVICE
Device
PORTA
PORTB
PORTC
PORTD
PORTE
PIC16(L)F1934 ●●●●●
PIC16(L)F1936 ●●●
PIC16(L)F1937 ●●●●●
QD
CK
Write LATx
Data Register
I/O pin
Read PORTx
Write PORTx
TRISx
Read LATx
Data Bus
To peripherals
ANSELx
VDD
VSS
; This code example illustrates
; initializing the PORTA register. The
; other ports are initialized in the same
; manner.
BANKSEL PORTA ;
CLRF PORTA ;Init PORTA
BANKSEL LATA ;Data Latch
CLRF LATA ;
BANKSEL ANSELA ;
CLRF ANSELA ;digital I/O
BANKSEL TRISA ;
MOVLW B'00111000' ;Set RA<5:3> as inputs
MOVWF TRISA ;and set RA<2:0> as
;outputs
PIC16(L)F1934/6/7
DS41364E-page 130 2008-2011 Microchip Technology Inc.
12.1 Alternate Pin Function
The Alternate Pin Function Control (APFCON) register
is used to steer specific peripheral input and output
functions between different pins. The APFCON register
is shown in Register 12-1. For this device family, the
following functions can be moved between different
pins.
•SS
(Slave Select)
P2B output
CCP2/P2A output
CCP3/P3A output
•Timer1 Gate
SR Latch SRNQ output
Comparator C2 output
These bits have no effect on the values of any TRIS
register. PORT and TRIS overrides will be routed to the
correct pin. The unselected pin will be unaffected.
2008-2011 Microchip Technology Inc. DS41364E-page 131
PIC16(L)F1934/6/7
REGISTER 12-1: APFCON: ALTERNATE PIN FUNCTION CONTROL REGISTER
U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
CCP3SEL T1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 Unimplemented: Read as ‘0’.
bit 6 CCP3SEL: CCP3 Input/Output Pin Selection bit
For 28-Pin Devices (PIC16F1936):
0 = CCP3/P3A function is on RC6/TX/CK/CCP3/P3A/SEG9
1 = CCP3/P3A function is on RB5/AN13/CPS5/CCP3/P3A/T1G/COM1
For 40-Pin Devices (PIC16F1934/7):
0 = CCP3/P3A function is on RE0/AN5/CCP3/P3A/SEG21
1 = CCP3/P3A function is on RB5/AN13/CPS5/CCP3/P3A/T1G/COM1
bit 5 T1GSEL: Timer1 Gate Input Pin Selection bit
0 = T1G function is on RB5/AN13/CPS5/CCP3/P3A/T1G/COM1
1 = T1G function is on RC4/SDI/SDA/T1G/SEG11
bit 4 P2BSEL: CCP2 PWM B Output Pin Selection bit
For 28-Pin Devices (PIC16F1936):
0 = P2B function is on RC0/T1OSO/T1CKI/P2B
1 = P2B function is on RB5/AN13/P2B/CPS5/T1G/COM1
For 40-Pin Devices (PIC16F1934/7):
0 = P2B function is on RC0/T1OSO/T1CKI/P2B
1 = P2B function is on RD2/CPS10/P2B
bit 3 SRNQSEL: SR Latch nQ Output Pin Selection bit
0 = SRnQ function is on RA5/AN4/C2OUT/SRnQ/SS/CPS7/SEG5/VCAP
1 = SRnQ function is on RA0/AN0/C12IN0-/C2OUT/SRnQ/SS/SEG12/VCAP
bit 2 C2OUTSEL: Comparator C2 Output Pin Selection bit
0 = C2OUT function is on RA5/AN4/C2OUT/SRnQ/SS/CPS7/SEG5/VCAP
1 = C2OUT function is on RA0/AN0/C12IN0-/C2OUT/SRnQ/SS/SEG12/VCAP
bit 1 SSSEL: SS Input Pin Selection bit
0 =SS
function is on RA5/AN4/C2OUT/SRNQ/SS/CPS7/SEG5/VCAP
1 =SS function is on RA0/AN0/C12IN0-/C2OUT/SRNQ/SS/SEG12/VCAP
bit 0 CCP2SEL: CCP2 Input/Output Pin Selection bit
0 = CCP2/P2A function is on RC1/T1OSI/CCP2/P2A
1 = CCP2/P2A function is on RB3/AN9/C12IN2-/CPS3/CCP2/P2A/VLCD3
PIC16(L)F1934/6/7
DS41364E-page 132 2008-2011 Microchip Technology Inc.
12.2 PORTA Registers
PORTA is a 8-bit wide, bidirectional port. The
corresponding data direction register is TRISA
(Register 12-3). Setting a TRISA bit (= 1) will make the
corresponding PORTA pin an input (i.e., disable the
output driver). Clearing a TRISA bit (= 0) will make the
corresponding PORTA pin an output (i.e., enables
output driver and puts the contents of the output latch
on the selected pin). Example 12-1 shows how to
initialize an I/O port.
Reading the PORTA register (Register 12-2) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then
written to the PORT data latch (LATA).
The TRISA register (Register 12-3) controls the
PORTA pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits
in the TRISA register are maintained set when using
them as analog inputs. I/O pins configured as analog
input always read 0’.
12.2.1 ANSELA REGISTER
The ANSELA register (Register 12-5) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELA bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELA bits has no effect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
12.2.2 PORTA FUNCTIONS AND OUTPUT
PRIORITIES
Each PORTA pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are shown in Tab le 1 2-2 .
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the highest priority.
Analog input functions, such as ADC, comparator and
CapSense inputs, are not shown in the priority lists.
These inputs are active when the I/O pin is set for
Analog mode using the ANSELx registers. Digital
output functions may control the pin when it is in Analog
mode with the priority shown in Table 12-2.
Note: The ANSELA bits default to the Analog
mode after Reset. To use any pins as
digital general purpose or peripheral
inputs, the corresponding ANSEL bits
must be initialized to ‘0’ by user software.
TABLE 12-2: PORTA OUTPUT PRIORITY
Pin Name Function Priority(1)
RA0 VCAP
SEG12 (LCD)
SRNQ (SR Latch)
C2OUT (Comparator)
RA0
RA1 SEG7 (LCD)
RA1
RA2 COM2 (LCD)
AN2 (DAC)
RA2
RA3 COM3 (LCD) 28-pin only
SEG15
RA3
RA4 SEG4 (LCD)
SRQ (SR Latch)
C1OUT (Comparator)
CCP5, 28-pin only
RA4
RA5 VCAP (enabled by Config. Word)
SEG5 (LCD)
SRNQ (SR Latch)
C2OUT (Comparator)
RA5
RA6 VCAP (enabled by Config. Word)
OSC2 (enabled by Config. Word)
CLKOUT (enabled by Config. Word)
SEG1 (LCD)
RA6
RA7 OSC1/CLKIN (enabled by Config. Word)
SEG2 (LCD)
RA7
Note 1: Priority listed from highest to lowest.
2008-2011 Microchip Technology Inc. DS41364E-page 133
PIC16(L)F1934/6/7
REGISTER 12-2: PORTA: PORTA REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 RA<7:0>: PORTA I/O Value bits(1)
1 = Port pin is > VIH
0 = Port pin is < VIL
Note 1: Writes to PORTA are actually written to corresponding LATA register. Reads from PORTA register is return
of actual I/O pin values.
REGISTER 12-3: TRISA: PORTA TRI-STATE REGISTER
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 TRISA<7:0>: PORTA Tri-State Control bit
1 = PORTA pin configured as an input (tri-stated)
0 = PORTA pin configured as an output
REGISTER 12-4: LATA: PORTA DATA LATCH REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 LATA<7:0>: PORTA Output Latch Value bits(1)
Note 1: Writes to PORTA are actually written to corresponding LATA register. Reads from PORTA register is return
of actual I/O pin values.
PIC16(L)F1934/6/7
DS41364E-page 134 2008-2011 Microchip Technology Inc.
REGISTER 12-5: ANSELA: PORTA ANALOG SELECT REGISTER
U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-6 Unimplemented: Read as0
bit 5-0 ANSA<5:0>: Analog Select between Analog or Digital Function on pins RA<5:0>, respectively
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.
2008-2011 Microchip Technology Inc. DS41364E-page 135
PIC16(L)F1934/6/7
TABLE 12-3: SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
TABLE 12-4: SUMMARY OF CONFIGURATION WORD WITH PORTA
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
ADCON0 CHS<4:0> GO/DONE ADON 163
ADCON1 ADFM ADCS<2:0> ADNREF ADPREF<1:0> 164
ANSELA ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 134
APFCON CCP3SEL T1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL 131
CM1CON0 C1ON C1OUT C1OE C1POL C1SP C1HYS C1SYNC 183
CM2CON0 C2ON C2OUT C2OE C2POL C2SP C2HYS C2SYNC 183
CM1CON1 C1NTP C1INTN C1PCH<1:0> C1NCH<1:0> 184
CM2CON1 C2NTP C2INTN C2PCH<1:0> C2NCH<1:0> 184
CPSCON0 CPSON ———CPSRNG<1:0> CPSOUT T0XCS 323
CPSCON1 ——— CPSCH<3:0> 324
DACCON0 DACEN DACLPS DACOE --- DACPSS<1:0> --- DACNSS 176
LATA LATA7 LATA6 LATA5 LATA4 LATA3 LATA2 LATA1 LATA0 133
LCDCON LCDEN SLPEN WERR CS<1:0> LMUX<1:0> 329
LCDSE0 SE7 SE6 SE5 SE4 SE3 SE2 SE1 SE0 333
LCDSE1 SE15 SE14 SE13 SE12 SE11 SE10 SE9 SE8 333
OPTION_REG WPUEN INTEDG TMR0CS TMR0SE PSA PS<2:0> 193
PORTA RA7 RA6 RA5 RA4 RA3 RA2 RA1 RA0 133
SRCON0 SRLEN SRCLK<2:0> SRQEN SRNQEN SRPS SRPR 189
SSPCON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 287
TRISA TRISA7TRISA6TRISA5TRISA4TRISA3TRISA2TRISA1TRISA0 133
Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTA.
Name Bits Bit -/7 Bit -/6 Bit 13/5 Bit 12/4 Bit 11/3 Bit 10/2 Bit 9/1 Bit 8/0 Register
on Pa ge
CONFIG1 13:8 FCMEN IESO CLKOUTEN BOREN<1:0> CPD 62
7:0 CP MCLRE PWRTE WDTE<1:0> FOSC<2:0>
CONFIG2 13:8 LVP DEBUG BORV STVREN PLLEN 64
7:0 VCAPEN<1:0>(1) WRT<1:0>
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by PORTA.
Note 1: PIC16F1934/6/7 only.
PIC16(L)F1934/6/7
DS41364E-page 136 2008-2011 Microchip Technology Inc.
12.3 PORTB Registers
PORTB is an 8-bit wide, bidirectional port. The
corresponding data direction register is TRISB
(Register 12-7). Setting a TRISB bit (= 1) will make the
corresponding PORTB pin an input (i.e., put the
corresponding output driver in a High-Impedance mode).
Clearing a TRISB bit (= 0) will make the corresponding
PORTB pin an output (i.e., enable the output driver and
put the contents of the output latch on the selected pin).
Example 12-1 shows how to initialize an I/O port.
Reading the PORTB register (Register 12-6) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then written
to the PORT data latch (LATB).
The TRISB register (Register 12-7) controls the PORTB
pin output drivers, even when they are being used as
analog inputs. The user should ensure the bits in the
TRISB register are maintained set when using them as
analog inputs. I/O pins configured as analog input always
read ‘0’.
12.3.1 WEAK PULL-UPS
Each of the PORTB pins has an individually configurable
internal weak pull-up. Control bits WPUB<7:0> enable or
disable each pull-up (see Register 12-10). Each weak
pull-up is automatically turned off when the port pin is
configured as an output. All pull-ups are disabled on a
Power-on Reset by the WPUEN bit of the OPTION_REG
register.
12.3.2 INTERRUPT-ON-CHANGE
All of the PORTB pins are individually configurable as an
interrupt-on-change pin. Control bits IOCB<7:0> enable
or disable the interrupt function for each pin. The
interrupt-on-change feature is disabled on a Power-on
Reset. Reference Section 13.0
“Interrupt-On-Change” for more information.
12.3.3 ANSELB REGISTER
The ANSELB register (Register 12-9) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELB bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELB bits has no effect on digital
output functions. A pin with TRIS clear and ANSELB set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
Note: The ANSELB bits default to the Analog
mode after Reset. To use any pins as
digital general purpose or peripheral
inputs, the corresponding ANSEL bits
must be initialized to ‘0’ by user software.
2008-2011 Microchip Technology Inc. DS41364E-page 137
PIC16(L)F1934/6/7
12.3.4 PORTB FUNCTIONS AND OUTPUT
PRIORITIES
Each PORTB pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are shown in Table 12-5.
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the highest priority.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions override other port
functions and are included in Table 12-5.
TABLE 12-5: PORTB OUTPUT PRIORITY
Pin Name Function Priority(1)
RB0 SEG0 (LCD)
CCP4, 28-pin only
RB0
RB1 P1C (ECCP1), 28-pin only
RB1
RB2 P1B (ECCP1), 28-pin only
RB2
RB3 CCP2/P2A
RB3
RB4 COM0
P1D, 28-pin only
RB4
RB5 COM1
P2B, 28-pin only
CCP3/P3A
RB5
RB6 ICSPCLK (Programming)
ICDCLK (enabled by Config. Word)
SEG14 (LCD)
RB6
RB7 ICSPDAT (Programming)
ICDDAT (enabled by Config. Word)
SEG13 (LCD)
RB7
Note 1: Priority listed from highest to lowest.
PIC16(L)F1934/6/7
DS41364E-page 138 2008-2011 Microchip Technology Inc.
REGISTER 12-6: PORTB: PORTB REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 RB<7:0>: PORTB I/O Pin bit
1 = Port pin is > VIH
0 = Port pin is < VIL
REGISTER 12-7: TRISB: PORTB TRI-STATE REGISTER
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 TRISB<7:0>: PORTB Tri-State Control bit
1 = PORTB pin configured as an input (tri-stated)
0 = PORTB pin configured as an output
REGISTER 12-8: LATB: PORTB DATA LATCH REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 LATB<7:0>: PORTB Output Latch Value bits(1)
Note 1: Writes to PORTB are actually written to corresponding LATB register. Reads from PORTB register is
return of actual I/O pin values.
2008-2011 Microchip Technology Inc. DS41364E-page 139
PIC16(L)F1934/6/7
REGISTER 12-9: ANSELB: PORTB ANALOG SELECT REGISTER
U-0 U-0 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-6 Unimplemented: Read as0
bit 5-0 ANSB<5:0>: Analog Select between Analog or Digital Function on Pins RB<5:0>, respectively
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.
REGISTER 12-10: WPUB: WEAK PULL-UP PORTB REGISTER
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 WPUB<7:0>: Weak Pull-up Register bits
1 = Pull-up enabled
0 = Pull-up disabled
Note 1: Global WPUEN bit of the OPTION_REG register must be cleared for individual pull-ups to be enabled.
2: The weak pull-up device is automatically disabled if the pin is in configured as an output.
PIC16(L)F1934/6/7
DS41364E-page 140 2008-2011 Microchip Technology Inc.
TABLE 12-6: SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
ADCON0 CHS<4:0> GO/DONE ADON 163
ANSELB ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 139
APFCON —CCP3SELT1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL 131
CCPxCON PxM<1:0> DCxB<1:0> CCPxM<3:0> 234
CPSCON0 CPSON CPSRNG<1:0> CPSOUT T0XCS 323
CPSCON1 CPSCH<3:> 324
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
IOCBP IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0 152
IOCBN IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0 152
IOCBF IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0 152
LATB LATB7 LATB6 LATB5 LATB4 LATB3 LATB2 LATB1 LATB0 138
LCDCON LCDEN SLPEN WERR CS<1:0> LMUX<1:0> 329
LCDSE0 SE7 SE6 SE5 SE4 SE3 SE2 SE1 SE0 333
LCDSE1 SE15 SE14 SE13 SE12 SE11 SE10 SE9 SE8 333
OPTION_REG WPUEN INTEDG TMR0CS TMR0SE PSA PS<2:0> 193
PORTB RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0 138
T1GCON TMR1GE T1GPOL T1GTM T1GSPM T1GGO/DONE T1GVAL T1GSS<1:0> 204
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
WPUB WPUB7 WPUB6 WPUB5 WPUB4 WPUB3 WPUB2 WPUB1 WPUB0 139
Legend: x = unknown, u = unchanged, - = unimplemented locations read as0’. Shaded cells are not used by PORTB.
2008-2011 Microchip Technology Inc. DS41364E-page 141
PIC16(L)F1934/6/7
12.4 PORTC Registers
PORTC is a 8-bit wide, bidirectional port. The
corresponding data direction register is TRISC
(Register 12-12). Setting a TRISC bit (= 1) will make the
corresponding PORTC pin an input (i.e., put the
corresponding output driver in a High-Impedance mode).
Clearing a TRISC bit (= 0) will make the corresponding
PORTC pin an output (i.e., enable the output driver and
put the contents of the output latch on the selected pin).
Example 12-1 shows how to initialize an I/O port.
Reading the PORTC register (Register 12-11) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then written
to the PORT data latch (LATC).
The TRISC register (Register 12-12) controls the
PORTC pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits in
the TRISC register are maintained set when using them
as analog inputs. I/O pins configured as analog input
always read ‘0’.
12.4.1 PORTC FUNCTIONS AND OUTPUT
PRIORITIES
Each PORTC pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are shown in Tab le 1 2-7 .
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the highest priority.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions override other port
functions and are included in Table 12-7.
TABLE 12-7: PORTC OUTPUT PRIORITY
Pin Name Function Priority(1)
RC0 T1OSO (Timer1 Oscillator)
CCP2/P2B
RC0
RC1 T1OSI (Timer1 Oscillator)
CCP2/P2A
RC1
RC2 SEG3 (LCD)
CCP1/P1A
RC2
RC3 SEG6 (LCD)
SCL (MSSP)
SCK (MSSP)
RC3
RC4 SEG11 (LCD)
SDA (MSSP)
RC4
RC5 SEG10 (LCD)
SDO (MSSP)
RC5
RC6 ISEG9 (LCD)
TX (EUSART)
CK (EUSART)
CCP3/P3A, 28-pin only
RC6
RC7 SEG8 (LCD)
DT (EUSART)
CCP3/P3B, 28 pin only
RC7
Note 1: Priority listed from highest to lowest.
PIC16(L)F1934/6/7
DS41364E-page 142 2008-2011 Microchip Technology Inc.
REGISTER 12-11: PORTC: PORTC REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 RC<7:0>: PORTC General Purpose I/O Pin bits
1 = Port pin is > VIH
0 = Port pin is < VIL
REGISTER 12-12: TRISC: PORTC TRI-STATE REGISTER
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 TRISC<7:0>: PORTC Tri-State Control bits
1 = PORTC pin configured as an input (tri-stated)
0 = PORTC pin configured as an output
REGISTER 12-13: LATC: PORTC DATA LATCH REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 LATC<7:0>: PORTC Output Latch Value bits(1)
Note 1: Writes to PORTC are actually written to corresponding LATC register. Reads from PORTC register is
return of actual I/O pin values.
2008-2011 Microchip Technology Inc. DS41364E-page 143
PIC16(L)F1934/6/7
TABLE 12-8: SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
APFCON —CCP3SELT1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL 131
CCPxCON PxM<1:0> DCxB<1:0> CCPxM<3:0> 234
LATC LATC7 LATC6 LATC5 LATC4 LATC3 LATC2 LATC1 LATC0 142
LCDCON LCDEN SLPEN WERR CS<1:0> LMUX<1:0> 329
LCDSE0 SE7 SE6 SE5 SE4 SE3 SE2 SE1 SE0 333
LCDSE1 SE15 SE14 SE13 SE12 SE11 SE10 SE9 SE8 333
PORTC RC7 RC6 RC5 RC4 RC3 RC2 RC1 RC0 142
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
SSPCON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 287
SSPSTAT SMP CKE D/A P S R/W UA BF 286
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON203
TXSTA CSRC TX9 TXEN SYNC BRGH TRMT TX9D 300
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
Legend: x = unknown, u = unchanged, - = unimplemented locations read as ‘0’. Shaded cells are not used by PORTC.
PIC16(L)F1934/6/7
DS41364E-page 144 2008-2011 Microchip Technology Inc.
12.5 PORTD Registers
PORTD is a 8-bit wide, bidirectional port. The
corresponding data direction register is TRISD
(Register 12-14). Setting a TRISD bit (= 1) will make the
corresponding PORTD pin an input (i.e., put the
corresponding output driver in a High-Impedance mode).
Clearing a TRISD bit (= 0) will make the corresponding
PORTD pin an output (i.e., enable the output driver and
put the contents of the output latch on the selected pin).
Example 12-1 shows how to initialize an I/O port.
Reading the PORTD register (Register 12-14) reads the
status of the pins, whereas writing to it will write to the
PORT latch. All write operations are read-modify-write
operations. Therefore, a write to a port implies that the
port pins are read, this value is modified and then written
to the PORT data latch (LATD).
The TRISD register (Register 12-15) controls the
PORTD pin output drivers, even when they are being
used as analog inputs. The user should ensure the bits
in the TRISD register are maintained set when using
them as analog inputs. I/O pins configured as analog
input always read 0’.
12.5.1 ANSELD REGISTER
The ANSELD register (Register 12-17) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELD bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELD bits has no effect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
12.5.2 PORTD FUNCTIONS AND OUTPUT
PRIORITIES
Each PORTD pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are shown in Tab le 1 2-9 .
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the highest priority.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions override other port
functions and are included in Tab le 1 2- 9 .
Note: PORTD is available on PIC16(L)F1934
and PIC16(L)F1937 only.
Note: The ANSELD bits default to the Analog
mode after Reset. To use any pins as
digital general purpose or peripheral
inputs, the corresponding ANSEL bits
must be initialized to ‘0’ by user software.
TABLE 12-9: PORTD OUTPUT PRIORITY
Pin Name Function Priority(1)
RD0 COM3 (LCD)
RD0
RD1 CCP4 (CCP)
RD1
RD2 P2B (CCP)
RD2
RD3 SEG16 (LCD)
P2C (CCP)
RD3
RD4 SEG17 (LCD)
P2D (CCP)
RD4
RD5 SEG18 (LCD)
P1B (CCP)
RD5
RD6 SEG19 (LCD)
P1C (CCP)
RD6
RD7 SEG20 (LCD)
P1D (CCP)
RD7
Note 1: Priority listed from highest to lowest.
2008-2011 Microchip Technology Inc. DS41364E-page 145
PIC16(L)F1934/6/7
REGISTER 12-14: PORTD: PORTD REGISTER(1)
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 RD<7:0>: PORTD General Purpose I/O Pin bits
1 = Port pin is > VIH
0 = Port pin is < VIL
Note 1: PORTD is not implemented on PIC16(L)F1936 devices, read as ‘0’.
REGISTER 12-15: TRISD: PORTD TRI-STATE REGISTER(1)
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 TRISD<7:0>: PORTD Tri-State Control bits
1 = PORTD pin configured as an input (tri-stated)
0 = PORTD pin configured as an output
Note 1: TRISD is not implemented on PIC16(L)F1936 devices, read as ‘0’.
2: PORTD implemented on PIC16(L)F1934/7 devices only.
REGISTER 12-16: LATD: PORTD DATA LATCH REGISTER
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 LATD<7:0>: PORTD Output Latch Value bits(1,2)
Note 1: Writes to PORTD are actually written to corresponding LATD register. Reads from PORTD register is
return of actual I/O pin values.
2: PORTD implemented on PIC16(L)F1934/7 devices only.
PIC16(L)F1934/6/7
DS41364E-page 146 2008-2011 Microchip Technology Inc.
TABLE 12-10: SUMMARY OF REGISTERS ASSOCIATED WITH PORTD(1)
REGISTER 12-17: ANSELD: PORTD ANALOG SELECT REGISTER(2)
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-0 ANSD<7:0>: Analog Select between Analog or Digital Function on Pins RD<7:0>, respectively
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.
2: ANSELD register is not implemented on the PIC16(L)F1936. Read as ‘0’.
3: PORTD implemented on PIC16(L)F1934/7 devices only.
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register on
Page
ANSELD ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0 146
CCPxCON PxM<1:0> DCxB<1:0> CCPxM<3:0> 234
CPSCON0 CPSON ———CPSRNG<1:0> CPSOUT T0XCS 323
CPSCON1 ——— CPSCH<3:0> 324
LATD LATD7 LATD6 LATD5 LATD4 LATD3 LATD2 LATD1 LATD0 145
LCDCON LCDEN SLPEN WERR CS<1:0> LMUX<1:0> 329
LCDSE2 SE23 SE22 SE21 SE20 SE19 SE18 SE17 SE16 333
PORTD RD7 RD6 RD5 RD4 RD3 RD2 RD1 RD0 145
TRISD TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 145
Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTD.
Note 1: These registers are not implemented on the PIC16(L)F1936 devices, read as ‘0’.
2008-2011 Microchip Technology Inc. DS41364E-page 147
PIC16(L)F1934/6/7
12.6 PORTE Registers
PORTE is a 4-bit wide, bidirectional port. The
corresponding data direction register is TRISE. Setting a
TRISE bit (= 1) will make the corresponding PORTE pin
an input (i.e., put the corresponding output driver in a
High-Impedance mode). Clearing a TRISE bit (= 0) will
make the corresponding PORTE pin an output (i.e.,
enable the output driver and put the contents of the
output latch on the selected pin). The exception is RE3,
which is input only and its TRIS bit will always read as
1’. Example 12-1 shows how to initialize an I/O port.
Reading the PORTE register (Register 12-18) reads
the status of the pins, whereas writing to it will write to
the PORT latch. All write operations are
read-modify-write operations. Therefore, a write to a
port implies that the port pins are read, this value is
modified and then written to the PORT data latch
(LATE). RE3 reads ‘0’ when MCLRE = 1.
12.6.1 ANSELE REGISTER
The ANSELE register (Register 12-21) is used to
configure the Input mode of an I/O pin to analog.
Setting the appropriate ANSELE bit high will cause all
digital reads on the pin to be read as ‘0’ and allow
analog functions on the pin to operate correctly.
The state of the ANSELE bits has no effect on digital
output functions. A pin with TRIS clear and ANSEL set
will still operate as a digital output, but the Input mode
will be analog. This can cause unexpected behavior
when executing read-modify-write instructions on the
affected port.
The TRISE register (Register 12-19) controls the PORTE
pin output drivers, even when they are being used as
analog inputs. The user should ensure the bits in the
TRISE register are maintained set when using them as
analog inputs. I/O pins configured as analog input always
read ‘0’.
12.6.2 PORTE FUNCTIONS AND OUTPUT
PRIORITIES
Each PORTD pin is multiplexed with other functions. The
pins, their combined functions and their output priorities
are shown in Tab le 1 2-11 .
When multiple outputs are enabled, the actual pin
control goes to the peripheral with the highest priority.
Analog input and some digital input functions are not
included in the list below. These input functions can
remain active when the pin is configured as an output.
Certain digital input functions override other port
functions and are included in Table 12-11.
Note: RE<2:0> and TRISE<2:0> pins are
available on PIC16(L)F1934 and
PIC16(L)F1937 only.
Note: The ANSELE bits default to the Analog
mode after Reset. To use any pins as
digital general purpose or peripheral
inputs, the corresponding ANSEL bits
must be initialized to ‘0’ by user software.
TABLE 12-11: PORTE OUTPUT PRIORITY
Pin Name Function Priority(1)
RE0 SEG21 (LCD)
CCP3/P3A (CCP)
RE0
RE1 SEG22 (LCD)
P3B (CCP)
RE1
RE2 SEG23 (LCD)
CCP5 (CCP)
RE2
Note 1: Priority listed from highest to lowest.
PIC16(L)F1934/6/7
DS41364E-page 148 2008-2011 Microchip Technology Inc.
REGISTER 12-18: PORTE: PORTE REGISTER
U-0 U-0 U-0 U-0 R-x/u R/W-x/u R/W-x/u R/W-x/u
RE3 RE2(1) RE1(1) RE0(1)
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-4 Unimplemented: Read as0
bit 3-0 RE<3:0>: PORTE I/O Pin bits(1)
1 = Port pin is > VIH
0 = Port pin is < VIL
Note 1: RE<2:0> are not implemented on the PIC16(L)F1936. Read as0’.
REGISTER 12-19: TR ISE: PORTE TRI-STATE REGISTER
U-0 U-0 U-0 U-0 U-1(2) R/W-1 R/W-1 R/W-1
TRISE2(1) TRISE1(1) TRISE0(1)
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-4 Unimplemented: Read as0
bit 3 Unimplemented: Read as1
bit 2-0 TRISE<2:0>: RE<2:0> Tri-State Control bits(1)
1 = PORTE pin configured as an input (tri-stated)
0 = PORTE pin configured as an output
Note 1: TRISE<2:0> are not implemented on the PIC16(L)F1936. Read as ‘0’.
2: Unimplemented, read as ‘1’.
2008-2011 Microchip Technology Inc. DS41364E-page 149
PIC16(L)F1934/6/7
REGISTER 12-20: LATE: PORTE DATA LATCH REGISTER
U-0 U-0 U-0 U-0 U-0 R/W-x/u R/W-x/u R/W-x/u
LATE2 LATE1 LATE0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-3 Unimplemented: Read as0
bit 2-0 LATE<2:0>: PORTE Output Latch Value bits(1)
Note 1: Writes to PORTE are actually written to corresponding LATE register. Reads from PORTE register is
return of actual I/O pin values.
REGISTER 12-21: ANSELE: PORTE ANALOG SELECT REGISTER
U-0 U-0 U-0 U-0 U-0 R/W-1 R/W-1 R/W-1
ANSE2(2) ANSE1(2) ANSE0(2)
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-3 Unimplemented: Read as0
bit 2-0 ANSE<2:0>: Analog Select between Analog or Digital Function on Pins RE<2:0>, respectively
0 = Digital I/O. Pin is assigned to port or digital special function.
1 = Analog input. Pin is assigned as analog input(1). Digital input buffer disabled.
Note 1: When setting a pin to an analog input, the corresponding TRIS bit must be set to Input mode in order to
allow external control of the voltage on the pin.
2: ANSELE register is not implemented on the PIC16(L)F1936. Read as ‘0
PIC16(L)F1934/6/7
DS41364E-page 150 2008-2011 Microchip Technology Inc.
TABLE 12-12: SUMMARY OF REGISTERS ASSOCIATED WITH PORTE
REGISTER 12-22: WPUE: WEAK PU LL-UP PORTE REGISTER
U-0 U-0 U-0 U-0 R/W-1/1 U-0 U-0 U-0
WPUE3
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-4 Unimplemented: Read as ‘0
bit 3 WPUE: Weak Pull-up Register bit
1 = Pull-up enabled
0 = Pull-up disabled
bit 2-0 Unimplemented: Read as ‘0
Note 1: Global WPUEN bit of the OPTION_REG register must be cleared for individual pull-ups to be enabled.
2: The weak pull-up device is automatically disabled if the pin is in configured as an output.
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
ADCON0 CHS<4:0> GO/DONE ADON 163
ANSELE —————ANSE2(1) ANSE1(1) ANSE0(1) 149
CCPxCON PxM<1:0> DCxB<1:0> CCPxM<3:0> 234
LATE —————LATE2(1) LATE1(1) LATE0(1) 149
LCDCON LCDEN SLPEN WERR CS<1:0> LMUX<1:0> 329
LCDSE2 SE23 SE22 SE21 SE20 SE19 SE18 SE17 SE16 333
PORTE ————RE3 RE2(1) RE1(1) RE0(1) 148
TRISE ————(2) TRISE2(1) TRISE1(1) TRISE0(1) 148
WPUE ————WPUE3 ———150
Legend: x = unknown, u = unchanged, – = unimplemented locations read as ‘0’. Shaded cells are not used by PORTE.
Note 1: These bits are not implemented on the PIC16(L)F1936 devices, read as ‘0’.
2: Unimplemented, read as ‘1’.
3: These registers/bits are not implemented on PIC16(L)F1936 devices, read as 0’.
2008-2011 Microchip Technology Inc. DS41364E-page 151
PIC16(L)F1934/6/7
13.0 INTERRUPT-ON-CHANGE
The PORTB pins can be configured to operate as
Interrupt-On-Change (IOC) pins. An interrupt can be
generated by detecting a signal that has either a rising
edge or a falling edge. Any individual PORT IOC pin, or
combination of PORT IOC pins, can be configured to
generate an interrupt. The interrupt-on-change module
has the following features:
Interrupt-on-Change enable (Master Switch)
Individual pin configuration
Rising and falling edge detection
Individual pin interrupt flags
Figure 13-1 is a block diagram of the IOC module.
13.1 Enabling the Module
To allow individual PORTB pins to generate an interrupt,
the IOCIE bit of the INTCON register must be set. If the
IOCIE bit is disabled, the edge detection on the pin will
still occur, but an interrupt will not be generated.
13.2 Individual Pin Configuration
For each PORTB pin, a rising edge detector and a falling
edge detector are present. To enable a pin to detect a
rising edge, the associated IOCBPx bit of the IOCBP
register is set. To enable a pin to detect a falling edge,
the associated IOCBNx bit of the IOCBN register is set.
A pin can be configured to detect rising and falling
edges simultaneously by setting both the IOCBPx bit
and the IOCBNx bit of the IOCBP and IOCBN registers,
respectively.
13.3 Interrupt Flags
The IOCBFx bits located in the IOCBF register are
status flags that correspond to the interrupt-on-change
pins of PORTB. If an expected edge is detected on an
appropriately enabled pin, then the status flag for that pin
will be set, and an interrupt will be generated if the IOCIE
bit is set. The IOCIF bit of the INTCON register reflects
the status of all IOCBFx bits.
13.4 Clearing Interrupt Flags
The individual status flags, (IOCBFx bits), can be
cleared by resetting them to zero. If another edge is
detected during this clearing operation, the associated
status flag will be set at the end of the sequence,
regardless of the value actually being written.
In order to ensure that no detected edge is lost while
clearing flags, only AND operations masking out known
changed bits should be performed. The following
sequence is an example of what should be performed.
EXAMPL E 13-1:
13.5 Operation in Sleep
The interrupt-on-change interrupt sequence will wake
the device from Sleep mode, if the IOCIE bit is set.
If an edge is detected while in Sleep mode, the IOCBF
register will be updated prior to the first instruction
executed out of Sleep.
FIGURE 13-1: INTERRUPT-ON-CHANGE BLOCK DIAGRAM
MOVLW 0xff
XORWF IOCBF, W
ANDWF IOCBF, F
RBx
From all other IOCBFx
individual pin detectors
DQ
CK
R
DQ
CK
R
IOCBNx
IOCBPx
Q2 Clock Cycle
IOCIE
IOC Interrupt to
CPU Core
IOCBFx
PIC16(L)F1934/6/7
DS41364E-page 152 2008-2011 Microchip Technology Inc.
13.6 Interrupt-On-Change Registers
REGISTER 13-1: IOCBP: INTERRUPT-ON-CHANGE POSITIVE EDGE REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 IOCBP<7:0>: Interrupt-on-Change Positive Edge Enable bits
1 = Interrupt-on-Change enabled on the pin for a positive going edge. Associated Status bit and
interrupt flag will be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin.
REGISTER 13-2: IOCBN: INTERRUPT-ON-CHANGE NEGATIVE EDGE REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 IOCBN<7:0>: Interrupt-on-Change Negative Edge Enable bits
1 = Interrupt-on-Change enabled on the pin for a negative going edge. Associated Status bit and
interrupt flag will be set upon detecting an edge.
0 = Interrupt-on-Change disabled for the associated pin.
REGISTER 13-3: IOCBF: INTERRUPT-ON-CHANGE FLAG REGISTER
R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0 R/W/HS-0/0
IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HS - Bit is set in hardware
bit 7-0 IOCBF<7:0>: Interrupt-on-Change Flag bits
1 = An enabled change was detected on the associated pin.
Set when IOCBPx = 1 and a rising edge was detected on RBx, or when IOCBNx = 1 and a falling
edge was detected on RBx.
0 = No change was detected, or the user cleared the detected change.
2008-2011 Microchip Technology Inc. DS41364E-page 153
PIC16(L)F1934/6/7
TABLE 13-1: SUMMARY OF REGISTERS ASSOCIATED WITH INTERRUPT-ON-CHANGE
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
ANSELB ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 139
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
IOCBF IOCBF7 IOCBF6 IOCBF5 IOCBF4 IOCBF3 IOCBF2 IOCBF1 IOCBF0 152
IOCBN IOCBN7 IOCBN6 IOCBN5 IOCBN4 IOCBN3 IOCBN2 IOCBN1 IOCBN0 152
IOCBP IOCBP7 IOCBP6 IOCBP5 IOCBP4 IOCBP3 IOCBP2 IOCBP1 IOCBP0 152
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used by Interrupt-on-Change.
PIC16(L)F1934/6/7
DS41364E-page 154 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 155
PIC16(L)F1934/6/7
14.0 FIXED VOLTAGE REFERENCE
(FVR)
The Fixed Voltage Reference, or FVR, is a stable
voltage reference, independent of VDD, with 1.024V,
2.048V or 4.096V selectable output levels. The output
of the FVR can be configured to supply a reference
voltage to the following:
ADC input channel
ADC positive reference
Comparator positive input
Digital-to-Analog Converter (DAC)
Capacitive Sensing (CPS) module
LCD bias generator
The FVR can be enabled by setting the FVREN bit of
the FVRCON register.
14.1 Independent Gain Amplifiers
The output of the FVR supplied to the ADC,
Comparators, DAC and CPS is routed through two
independent programmable gain amplifiers. Each
amplifier can be configured to amplify the reference
voltage by 1x, 2x or 4x, to produce the three possible
voltage levels.
The ADFVR<1:0> bits of the FVRCON register are
used to enable and configure the gain amplifier settings
for the reference supplied to the ADC module. Refer-
ence Section 15.0 “Analog-to-Digital Converter
(ADC) Module” for additional information.
The CDAFVR<1:0> bits of the FVRCON register are used
to enable and configure the gain amplifier settings for the
reference supplied to the DAC, CPS and comparator
module. Reference Section 17.0 “Digital-to-Analog
Converter (DAC) Module”, Section 18.0 “Comparator
Module” and Section 26.0 “Capacitive Sensing (CPS)
Module” for additional information.
14.2 FVR Stabilization Period
When the Fixed Voltage Reference module is enabled, it
requires time for the reference and amplifier circuits to
stabilize. Once the circuits stabilize and are ready for use,
the FVRRDY bit of the FVRCON register will be set. See
in the applicable Electrical Specifications Chapter for
the minimum delay requirement.
FIGURE 14-1: VOLTAGE REFERENCE BLOCK DIAGRAM
ADFVR<1:0>
CDAFVR<1:0>
X1
X2
X4
X1
X2
X4
2
2
FVR BUFFER1
(To ADC Module)
FVR BUFFER2
(To Comparators, DAC)
FVR VREF
(To LCD Bias Generator)
+
_
FVREN
FVRRDY
1.024V Fixed
Reference
PIC16(L)F1934/6/7
DS41364E-page 156 2008-2011 Microchip Technology Inc.
14.3 FVR Control Registers
TABLE 14-1: SUMMARY OF REGISTERS ASSOCIATED WITH FIXED VO LTAGE REFERENCE
REGISTER 14-1: FVRCON: FIXED VOLTAGE REFERENCE CONTROL REGISTER
R/W-0/0 R-q/q R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
FVREN FVRRDY(1) TSEN TSRNG CDAFVR<1:0> ADFVR<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared q = Value depends on condition
bit 7 FVREN: Fixed Voltage Reference Enable bit
0 = Fixed Voltage Reference is disabled
1 = Fixed Voltage Reference is enabled
bit 6 FVRRDY: Fixed Voltage Reference Ready Flag bit(1)
0 = Fixed Voltage Reference output is not ready or not enabled
1 = Fixed Voltage Reference output is ready for use
bit 5 TSEN: Temperature Indicator Enable bit(3)
0 = Temperature Indicator is disabled
1 = Temperature Indicator is enabled
bit 4 TSRNG: Temperature Indicator Range Selection bit(3)
0 =VOUT = VDD - 2VT (Low Range)
1 =V
OUT = VDD - 4VT (High Range)
bit 3-2 CDAFVR<1:0>: Comparator and DAC Fixed Voltage Reference Selection bit
00 = Comparator and DAC Fixed Voltage Reference Peripheral output is off.
01 = Comparator and DAC Fixed Voltage Reference Peripheral output is 1x (1.024V)
10 = Comparator and DAC Fixed Voltage Reference Peripheral output is 2x (2.048V)(2)
11 = Comparator and DAC Fixed Voltage Reference Peripheral output is 4x (4.096V)(2)
bit 1-0 ADFVR<1:0>: ADC Fixed Voltage Reference Selection bit
00 = ADC Fixed Voltage Reference Peripheral output is off.
01 = ADC Fixed Voltage Reference Peripheral output is 1x (1.024V)
10 = ADC Fixed Voltage Reference Peripheral output is 2x (2.048V)(2)
11 = ADC Fixed Voltage Reference Peripheral output is 4x (4.096V)(2)
Note 1: FVRRDY is always ‘1’ on devices with LDO (PIC16F1934/6/7).
2: Fixed Voltage Reference output cannot exceed VDD.
3: See Section 16.0 “Temperature Indicator Module” for additional information.
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Regi ster
on page
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 156
Legend: Shaded cells are not used with the Fixed Voltage Reference.
2008-2011 Microchip Technology Inc. DS41364E-page 157
PIC16(L)F1934/6/7
15.0 ANALOG-TO-DIGITAL
CONVERTER (ADC) MODULE
The Analog-to-Digital Converter (ADC) allows
conversion of an analog input signal to a 10-bit binary
representation of that signal. This device uses analog
inputs, which are multiplexed into a single sample and
hold circuit. The output of the sample and hold is
connected to the input of the converter. The converter
generates a 10-bit binary result via successive
approximation and stores the conversion result into the
ADC result registers (ADRESH:ADRESL register pair).
Figure 15-1 shows the block diagram of the ADC.
The ADC voltage reference is software selectable to be
either internally generated or externally supplied.
The ADC can generate an interrupt upon completion of
a conversion. This interrupt can be used to wake-up the
device from Sleep.
FIGURE 15-1: ADC BLOCK DIAGRAM
DAC
VDD
VREF+ADPREF = 10
ADPREF = 00
ADPREF = 11
FVR Buffer1
VSS
VREF-ADNREF = 1
ADNREF = 0
Note 1: When ADON = 0, all multiplexer inputs are disconnected.
2: Not available on PIC16(L)F1936.
ADON(1)
GO/DONE
VSS
ADC
00000
00001
00010
00011
00100
00101
00111
00110
01000
01001
01010
01011
01100
01101
11110
CHS<4:0>
AN0
AN1
AN2
AN4
AN5(2)
AN6(2)
AN7(2)
AN3
AN8
AN9
AN10
AN11
AN12
AN13
11111
ADRESH ADRESL
10
16
ADFM 0 = Left Justify
1 = Right Justify
Temperature Sensor 11101
PIC16(L)F1934/6/7
DS41364E-page 158 2008-2011 Microchip Technology Inc.
15.1 ADC Configuration
When configuring and using the ADC the following
functions must be considered:
Port configuration
Channel selection
ADC voltage reference selection
ADC conversion clock source
Interrupt control
Result formatting
15.1.1 PORT CONFIGURATION
The ADC can be used to convert both analog and
digital signals. When converting analog signals, the I/O
pin should be configured for analog by setting the
associated TRIS and ANSEL bits. Refer to
Section 12.0 “I/O Ports” for more information.
15.1.2 CHANNEL SELECTION
There are 17 channel selections available:
AN<13:0> pins
Temperature Indicator
DAC Output
FVR (Fixed Voltage Reference) Output
Refer to Section 16.0 “Temperature Indicator Mod-
ule”, Section 17.0 “Digital-to-Analog Converter
(DAC) Module” and Section 14.0 “Fixed Voltage
Reference (FV R)” for more information on these chan-
nel selections.
The CHS bits of the ADCON0 register determine which
channel is connected to the sample and hold circuit.
When changing channels, a delay is required before
starting the next conversion. Refer to Section 15.2
“ADC Operation” for more information.
15.1.3 ADC VOLTAGE REFERENCE
The ADPREF bits of the ADCON1 register provides
control of the positive voltage reference. The positive
voltage reference can be:
•V
REF+ pin
•VDD
FVR 2.048V
FVR 4.096V (Not available on LF devices)
The ADNREF bits of the ADCON1 register provides
control of the negative voltage reference. The negative
voltage reference can be:
•V
REF- pin
•V
SS
See Section 14.0 “Fixed Voltage Reference (FVR)”
for more details on the fixed voltage reference.
15.1.4 CONVERSION CLOCK
The source of the conversion clock is software select-
able via the ADCS bits of the ADCON1 register. There
are seven possible clock options:
•F
OSC/2
•FOSC/4
•FOSC/8
•F
OSC/16
•FOSC/32
•FOSC/64
•F
RC (dedicated internal oscillator)
The time to complete one bit conversion is defined as
TAD. One full 10-bit conversion requires 11.5 TAD
periods as shown in Figure 15-2.
For correct conversion, the appropriate TAD specifica-
tion must be met. Refer to the A/D conversion require-
ments in the applicable Electrical Specifications
Chapter for more information. Tab le 15 - 1 gives exam-
ples of appropriate ADC clock selections.
Note: Analog voltages on any pin that is defined
as a digital input may cause the input buf-
fer to conduct excess current.
Note: Unless using the FRC, any changes in the
system clock frequency will change the
ADC clock frequency, which may
adversely affect the ADC result.
2008-2011 Microchip Technology Inc. DS41364E-page 159
PIC16(L)F1934/6/7
TABLE 15-1: ADC CLOCK PERIOD (TAD) VS. DEVICE OPERATING FREQUENCIES
FIGURE 15-2: ANALOG-TO-DIGITAL CONVERSION TAD CYCLES
ADC Clock Period (TAD)Device Frequency (FOSC)
Device Frequency (FOSC)
ADC
Clock Source ADCS<2:0> 32 MHz 20 MHz 16 MHz 8 MHz 4 MHz 1 MHz
Fosc/2 000 62.5ns(2) 100 ns(2) 125 ns(2) 250 ns(2) 500 ns(2) 2.0 s
Fosc/4 100 125 ns(2) 200 ns(2) 250 ns(2) 500 ns(2) 1.0 s4.0 s
Fosc/8 001 0.5 s(2) 400 ns(2) 0.5 s(2) 1.0 s2.0 s8.0 s(3)
Fosc/16 101 800 ns 800 ns 1.0 s2.0 s4.0 s16.0 s(3)
Fosc/32 010 1.0 s1.6 s2.0 s4.0 s8.0 s(3) 32.0 s(3)
Fosc/64 110 2.0 s3.2 s4.0 s8.0 s(3) 16.0 s(3) 64.0 s(3)
FRC x11 1.0-6.0 s(1,4) 1.0-6.0 s(1,4) 1.0-6.0 s(1,4) 1.0-6.0 s(1,4) 1.0-6.0 s(1,4) 1.0-6.0 s(1,4)
Legend: Shaded cells are outside of recommended range.
Note 1: The FRC source has a typical TAD time of 1.6 s for VDD.
2: These values violate the minimum required TAD time.
3: For faster conversion times, the selection of another clock source is recommended.
4: The ADC clock period (TAD) and total ADC conversion time can be minimized when the ADC clock is derived from the
system clock FOSC. However, the FRC clock source must be used when conversions are to be performed with the
device in Sleep mode.
TAD1TAD2TAD3TAD4 TAD5TAD6 TAD7TAD8 TAD11
Set GO bit
Holding capacitor is disconnected from analog input (typically 100 ns)
TAD9 TAD10
TCY - TAD
ADRESH:ADRESL is loaded, GO bit is cleared,
ADIF bit is set, holding capacitor is connected to analog input.
Conversion starts
b0
b9 b6 b5 b4 b3 b2 b1
b8 b7
On the following cycle:
PIC16(L)F1934/6/7
DS41364E-page 160 2008-2011 Microchip Technology Inc.
15.1.5 INTERRUPTS
The ADC module allows for the ability to generate an
interrupt upon completion of an Analog-to-Digital
conversion. The ADC Interrupt Flag is the ADIF bit in
the PIR1 register. The ADC Interrupt Enable is the
ADIE bit in the PIE1 register. The ADIF bit must be
cleared in software.
This interrupt can be generated while the device is
operating or while in Sleep. If the device is in Sleep, the
interrupt will wake-up the device. Upon waking from
Sleep, the next instruction following the SLEEP instruc-
tion is always executed. If the user is attempting to
wake-up from Sleep and resume in-line code execu-
tion, the GIE and PEIE bits of the INTCON register
must be disabled. If the GIE and PEIE bits of the
INTCON register are enabled, execution will switch to
the Interrupt Service Routine.
Please refer to Section 15.1.5 “Interrupts” for more
information.
15.1.6 RESULT FORMATTING
The 10-bit A/D conversion result can be supplied in two
formats, left justified or right justified. The ADFM bit of
the ADCON1 register controls the output format.
Figure 15-3 shows the two output formats.
FIGURE 15-3: 10-BIT A/D CONVERSION RESULT FORMAT
Note 1: The ADIF bit is set at the completion of
every conversion, regardless of whether
or not the ADC interrupt is enabled.
2: The ADC operates during Sleep only
when the FRC oscillator is selected.
ADRESH ADRESL
(ADFM = 0)MSB LSB
bit 7 bit 0 bit 7 bit 0
10-bit A/D Result Unimplemented: Read as 0
(ADFM = 1)MSB LSB
bit 7 bit 0 bit 7 bit 0
Unimplemented: Read as ‘0 10-bit A/D Result
2008-2011 Microchip Technology Inc. DS41364E-page 161
PIC16(L)F1934/6/7
15.2 ADC Operation
15.2.1 STARTING A CONVERSION
To enable the ADC module, the ADON bit of the
ADCON0 register must be set to a ‘1’. Setting the GO/
DONE bit of the ADCON0 register to a ‘1’ will start the
Analog-to-Digital conversion.
15.2.2 COMPLETION OF A CONVERSION
When the conversion is complete, the ADC module will:
Clear the GO/DONE bit
Set the ADIF Interrupt Flag bit
Update the ADRESH and ADRESL registers with
new conversion result
15.2.3 TERMINATING A CONVERSION
If a conversion must be terminated before completion,
the GO/DONE bit can be cleared in software. The
ADRESH and ADRESL registers will be updated with
the partially complete Analog-to-Digital conversion
sample. Incomplete bits will match the last bit
converted.
15.2.4 ADC OPERATION DURING SLEEP
The ADC module can operate during Sleep. This
requires the ADC clock source to be set to the FRC
option. When the FRC clock source is selected, the
ADC waits one additional instruction before starting the
conversion. This allows the SLEEP instruction to be
executed, which can reduce system noise during the
conversion. If the ADC interrupt is enabled, the device
will wake-up from Sleep when the conversion
completes. If the ADC interrupt is disabled, the ADC
module is turned off after the conversion completes,
although the ADON bit remains set.
When the ADC clock source is something other than
FRC, a SLEEP instruction causes the present conver-
sion to be aborted and the ADC module is turned off,
although the ADON bit remains set.
15.2.5 SPECIAL EVENT TRIGGER
The Special Event Trigger of the CCPx/ECCPX module
allows periodic ADC measurements without software
intervention. When this trigger occurs, the GO/DONE
bit is set by hardware and the Timer1 counter resets to
zero.
Using the Special Event Trigger does not assure proper
ADC timing. It is the user’s responsibility to ensure that
the ADC timing requirements are met.
Refer to Section 23.0 “Capture/Compare/PWM
Modules” for more information.
Note: The GO/DONE bit should not be set in the
same instruction that turns on the ADC.
Refer to Section 15.2.6 “A/D Conver-
sion Procedure”.
Note: A device Reset forces all registers to their
Reset state. Thus, the ADC module is
turned off and any pending conversion is
terminated.
TABLE 15-2: SPECIAL EVENT TRIGGER
Device CCPx/ECCPx
PIC16(L)F1934/6/7 CCP5
PIC16(L)F1934/6/7
DS41364E-page 162 2008-2011 Microchip Technology Inc.
15.2.6 A/D CONVERSION PROCEDURE
This is an example procedure for using the ADC to
perform an Analog-to-Digital conversion:
1. Configure Port:
Disable pin output driver (Refer to the TRIS
register)
Configure pin as analog (Refer to the ANSEL
register)
2. Configure the ADC module:
Select ADC conversion clock
Configure voltage reference
Select ADC input channel
Turn on ADC module
3. Configure ADC interrupt (optional):
Clear ADC interrupt flag
Enable ADC interrupt
Enable peripheral interrupt
Enable global interrupt(1)
4. Wait the required acquisition time(2).
5. Start conversion by setting the GO/DONE bit.
6. Wait for ADC conversion to complete by one of
the following:
Polling the GO/DONE bit
Waiting for the ADC interrupt (interrupts
enabled)
7. Read ADC Result.
8. Clear the ADC interrupt flag (required if interrupt
is enabled).
EXAMPLE 15-1: A/D CONVE RSION
Note 1: The global interrupt can be disabled if the
user is attempting to wake-up from Sleep
and resume in-line code execution.
2: Refer to Section 15.3 “A/D Acquisition
Requirements”.
;This code block configures the ADC
;for polling, Vdd and Vss references, Frc
;clock and AN0 input.
;
;Conversion start & polling for completion
; are included.
;
BANKSEL ADCON1 ;
MOVLW B’11110000’ ;Right justify, Frc
;clock
MOVWF ADCON1 ;Vdd and Vss Vref
BANKSEL TRISA ;
BSF TRISA,0 ;Set RA0 to input
BANKSEL ANSEL ;
BSF ANSEL,0 ;Set RA0 to analog
BANKSEL ADCON0 ;
MOVLW B’00000001’ ;Select channel AN0
MOVWF ADCON0 ;Turn ADC On
CALL SampleTime ;Acquisiton delay
BSF ADCON0,ADGO ;Start conversion
BTFSC ADCON0,ADGO ;Is conversion done?
GOTO $-1 ;No, test again
BANKSEL ADRESH ;
MOVF ADRESH,W ;Read upper 2 bits
MOVWF RESULTHI ;store in GPR space
BANKSEL ADRESL ;
MOVF ADRESL,W ;Read lower 8 bits
MOVWF RESULTLO ;Store in GPR space
2008-2011 Microchip Technology Inc. DS41364E-page 163
PIC16(L)F1934/6/7
15.2.7 ADC REGISTER DEFINITIONS
The following registers are used to control the
operation of the ADC.
REGISTER 15-1: ADCON0: A/D CONTROL REGISTER 0
U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
CHS<4:0> GO/DONE ADON
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 Unimplemented: Read as ‘0
bit 6-2 CHS<4:0>: Analog Channel Select bits
00000 =AN0
00001 =AN1
00010 =AN2
00011 =AN3
00100 =AN4
00101 =AN5
(4)
00110 =AN6
(4)
00111 =AN7
(4)
01000 =AN8
01001 =AN9
01010 =AN10
01011 =AN11
01100 =AN12
01101 =AN13
01110 = Reserved. No channel connected.
11100 = Reserved. No channel connected.
11101 = Temperature Indicator(3)
11110 = DAC output(1)
11111 = FVR (Fixed Voltage Reference) Buffer 1 Output(2)
bit 1 GO/DONE: A/D Conversion Status bit
1 = A/D conversion cycle in progress. Setting this bit starts an A/D conversion cycle.
This bit is automatically cleared by hardware when the A/D conversion has completed.
0 = A/D conversion completed/not in progress
bit 0 ADON: ADC Enable bit
1 = ADC is enabled
0 = ADC is disabled and consumes no operating current
Note 1: See Section 17.0 “Digital-to-Analog Converter (DAC) Module” for more information.
2: See Section 14.0 “Fixed Voltage Reference (FVR)” for more information.
3: See Section 16.0 “Temperature Indicator Module” for more information.
4: Not available on the PIC16(L)F1936.
PIC16(L)F1934/6/7
DS41364E-page 164 2008-2011 Microchip Technology Inc.
REGISTER 15-2: ADCON1: A/D CONTROL REGISTER 1
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
ADFM ADCS<2:0> ADNREF ADPREF<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 ADFM: A/D Result Format Select bit
1 = Right justified. Six Most Significant bits of ADRESH are set to ‘0’ when the conversion result is
loaded.
0 = Left justified. Six Least Significant bits of ADRESL are set to ‘0’ when the conversion result is
loaded.
bit 6-4 ADCS<2:0>: A/D Conversion Clock Select bits
000 =F
OSC/2
001 =F
OSC/8
010 =F
OSC/32
011 =F
RC (clock supplied from a dedicated RC oscillator)
100 =F
OSC/4
101 =F
OSC/16
110 =F
OSC/64
111 =F
RC (clock supplied from a dedicated RC oscillator)
bit 3 Unimplemented: Read as ‘0
bit 2 ADNREF: A/D Negative Voltage Reference Configuration bit
0 =VREF- is connected to VSS
1 =VREF- is connected to external VREF- pin(1)
bit 1-0 ADPREF<1:0>: A/D Positive Voltage Reference Configuration bits
00 =V
REF+ is connected to VDD
01 = Reserved
10 =V
REF+ is connected to external VREF+ pin(1)
11 =VREF+ is connected to internal Fixed Voltage Reference (FVR) module(1)
Note 1: When selecting the FVR or the VREF+ pin as the source of the positive reference, be aware that a
minimum voltage specification exists. See the applicable Electrical Specifications Chapter for details.
2008-2011 Microchip Technology Inc. DS41364E-page 165
PIC16(L)F1934/6/7
REGISTER 15-3: ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 0
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<9:2>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-0 ADRES<9:2>: ADC Result Register bits
Upper 8 bits of 10-bit conversion result
REGISTER 15-4: ADRESL: ADC RESULT REGISTER LOW (ADRESL) ADFM = 0
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-6 ADRES<1:0>: ADC Result Register bits
Lower 2 bits of 10-bit conversion result
bit 5-0 Reserved: Do not use.
PIC16(L)F1934/6/7
DS41364E-page 166 2008-2011 Microchip Technology Inc.
REGISTER 15-5: ADRESH: ADC RESULT REGISTER HIGH (ADRESH) ADFM = 1
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<9:8>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-2 Reserved: Do not use.
bit 1-0 ADRES<9:8>: ADC Result Register bits
Upper 2 bits of 10-bit conversion result
REGISTER 15-6: ADRESL: ADC RESULT REGISTER LOW (ADRESL) ADFM = 1
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
ADRES<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-0 ADRES<7:0>: ADC Result Register bits
Lower 8 bits of 10-bit conversion result
2008-2011 Microchip Technology Inc. DS41364E-page 167
PIC16(L)F1934/6/7
15.3 A/D Acquisition Requirements
For the ADC to meet its specified accuracy, the charge
holding capacitor (CHOLD) must be allowed to fully
charge to the input channel voltage level. The Analog
Input model is shown in Figure 15-4. The source
impedance (RS) and the internal sampling switch (RSS)
impedance directly affect the time required to charge
the capacitor CHOLD. The sampling switch (RSS)
impedance varies over the device voltage (VDD), refer
to Figure 15-4. The maximum recommended
impedance for analog sources is 10 k. As the
source impedance is decreased, the acquisition time
may be decreased. After the analog input channel is
selected (or changed), an A/D acquisition must be
done before the conversion can be started. To calculate
the minimum acquisition time, Equation 15-1 may be
used. This equation assumes that 1/2 LSb error is used
(1,024 steps for the ADC). The 1/2 LSb error is the
maximum error allowed for the ADC to meet its
specified resolution.
EQUATION 15-1: ACQUISITION TIME EXAMPLE
TACQ Amplifier Settling Time Hold Ca pacitor Charging Time Temperature Coeffici e nt++=
TAMP TCTCOFF++=
2µs TCTemperature - 25°C0.05µs/°C++=
TCCHOLD RIC RSS RS++ ln(1/511)=
10pF 1k
7k
10k
++ ln(0.001957)=
1.12=µs
VAPPLIED 1e
Tc
RC
---------



VAPPLIED 11
2n1+
1
--------------------------


=
VAPPLIED 11
2n1+
1
--------------------------


VCHOLD=
VAPPLIED 1e
TC
RC
----------



VCHOLD=
;[1] VCHOLD charged to within 1/2 lsb
;[2] VCHOLD char ge res pon se to VAPPLIED
;combining [1] and [2]
The value for TC can be approximated with the following equations:
Solving for TC:
Therefore:
Temperature 50°C and external impedance of 10k
5.0V V DD=
Assumptions:
Note: Where n = number of bits of the ADC.
TACQ 2µs 1.12µs 50°C- 25°C0.05µs/°C++=
4.42µs=
Note 1: The reference voltage (VREF) has no effect on the equation, since it cancels itself out.
2: The charge holding capacitor (CHOLD) is not discharged after each conversion.
3: The maximum recommended impedance for analog sources is 10 k. This is required to meet the pin
leakage specification.
PIC16(L)F1934/6/7
DS41364E-page 168 2008-2011 Microchip Technology Inc.
FIGURE 15-4: ANALOG INPUT MODEL
FIGURE 15-5: ADC TRANSFER FUNCTION
CPIN
VA
Rs
Analog
5 pF
VDD
VT 0.6V
VT 0.6V I LEAKAGE(1)
RIC 1k
Sampling
Switch
SS Rss
CHOLD = 10 pF
VSS/VREF-
6V
Sampling Switch
5V
4V
3V
2V
567891011
(k)
VDD
Legend:
CPIN
VT
I LEAKAGE
RIC
SS
CHOLD
= Input Capacitance
= Threshold Voltage
= Leakage current at the pin due to
= Interconnect Resistance
= Sampling Switch
= Sample/Hold Capacitance
various junctions
RSS
Note 1: Refer to in the applicable Electrical Specifications Chapter.
RSS = Resistance of Sampling Switch
Input
pin
3FFh
3FEh
ADC Output Code
3FDh
3FCh
03h
02h
01h
00h
Full-Scale
3FBh
0.5 LSB
VREF-Zero-Scale
Transition VREF+
Transition
1.5 LSB
Full-Scale Range
Analog Input Voltage
2008-2011 Microchip Technology Inc. DS41364E-page 169
PIC16(L)F1934/6/7
TABLE 15-3: SUMMARY OF REGISTERS ASSOCIATED WITH ADC
Name Bit 7 B it 6 B it 5 B it 4 B it 3 B it 2 Bit 1 Bit 0 Register
on Page
ADCON0 CHS<4:0> GO/DONE ADON 163
ADCON1 ADFM ADCS<2:0> ADNREF ADPREF<1:0> 164
ADRESH A/D Result Register High 165
ADRESL A/D Result Register Low 165
ANSELA —ANSA5ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 134
ANSELB ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 139
ANSELE ———— ANSE2 ANSE1 ANSE0 149
CCP1CON P1M<1:0> DC1B<1:0> CCP1M<3:0> 234
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISE ————(1) TRISE2(2) TRISE1(2) TRISE0(2) 148
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 156
DACCON0 DACEN DACLPS DACOE DACPSS<1:0> DACNSS 176
DACCON1 —— DACR<4:0> 176
Legend: x = unknown, u = unchanged, = unimplemented read as ‘0’, q = value depends on condition. Shaded cells are not
used for ADC module.
Note 1: Unimplemented, read as1’.
2: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
PIC16(L)F1934/6/7
DS41364E-page 170 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 171
PIC16(L)F1934/6/7
16.0 TEMPERATURE INDICATOR
MODULE
This family of devices is equipped with a temperature
circuit designed to measure the operating temperature
of the silicon die. The circuit’s range of operating
temperature falls between -40°C and +85°C. The
output is a voltage that is proportional to the device
temperature. The output of the temperature indicator is
internally connected to the device ADC.
The circuit may be used as a temperature threshold
detector or a more accurate temperature indicator,
depending on the level of calibration performed. A one-
point calibration allows the circuit to indicate a
temperature closely surrounding that point. A two-point
calibration allows the circuit to sense the entire range
of temperature more accurately. Reference Application
Note AN1333, “Use and Calibration of the Internal
Temperature Indicator” (DS01333) for more details
regarding the calibration process.
16.1 Circuit Operation
Figure 16-1 shows a simplified block diagram of the
temperature circuit. The proportional voltage output is
achieved by measuring the forward voltage drop across
multiple silicon junctions.
Equation 16-1 describes the output characteristics of
the temperature indicator.
EQUATION 16-1: VOUT RANGES
The temperature sense circuit is integrated with the
Fixed Voltage Reference (FVR) module. See
Section 14.0 “Fixed Voltage Reference (FVR)” for
more information.
The circuit is enabled by setting the TSEN bit of the
FVRCON register. When disabled, the circuit draws no
current.
The circuit operates in either high or low range. The high
range, selected by setting the TSRNG bit of the
FVRCON register, provides a wider output voltage. This
provides more resolution over the temperature range,
but may be less consistent from part to part. This range
requires a higher bias voltage to operate and thus, a
higher VDD is needed.
The low range is selected by clearing the TSRNG bit of
the FVRCON register. The low range generates a lower
voltage drop and thus, a lower bias voltage is needed to
operate the circuit. The low range is provided for low
voltage operation.
FIGURE 16-1: TEMPERATURE CIRCUIT
DIAGRAM
16.2 Minimum Operating VDD vs.
Minimum Sensing Temperature
When the temperature circuit is operated in low range,
the device may be operated at any operating voltage
that is within specifications.
When the temperature circuit is operated in high range,
the device operating voltage, VDD, must be high
enough to ensure that the temperature circuit is cor-
rectly biased.
Table 16-1 shows the recommended minimum VDD vs.
range setting.
TABLE 16-1: RECOMMENDED VDD VS.
RANGE
16.3 Temperature Output
The output of the circuit is measured using the internal
Analog-to-Digital Converter. A channel is reserved for
the temperature circuit output. Refer to Section 16.0
“Analog-to-Digital Converter (ADC) Module” for
detailed information.
16.4 ADC Acquisition Time
To ensure accurate temperature measurements, the
user must wait at least 200 s after the ADC input
multiplexer is connected to the temperature indicator
output before the conversion is performed. In addition,
the user must wait 200 s between sequential
conversions of the temperature indicator output.
High Range: VOUT = VDD - 4VT
Low R ange: VOUT = VDD - 2VT
Min. VDD, TSRNG = 1Min. VDD, TSRNG = 0
3.6V 1.8V
TSEN
ADC
MUX
TSRNG
VDD
ADC
CHS bits
(ADCON0 register)
n
VOUT
PIC16(L)F1934/6/7
DS41364E-page 172 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 173
PIC16(L)F1934/6/7
17.0 DIGITAL-TO-ANALOG
CONVERTER (DAC) MODULE
The Digital-to-Analog Converter supplies a variable
voltage reference, ratiometric with the input source,
with 32 selectable output levels.
The input of the DAC can be connected to:
•External V
REF pins
•VDD supply voltage
FVR (Fixed Voltage Reference)
The output of the DAC can be configured to supply a
reference voltage to the following:
Comparator positive input
ADC input channel
•DACOUT pin
Capacitive Sensing module (CSM)
The Digital-to-Analog Converter (DAC) can be enabled
by setting the DACEN bit of the DACCON0 register.
17.1 Output Volt age Selection
The DAC has 32 voltage level ranges. The 32 levels
are set with the DACR<4:0> bits of the DACCON1
register.
The DAC output voltage is determined by the following
equations:
EQUATION 17-1: DAC OUTPUT VOLTAGE
17.2 Ratiometric Output Level
The DAC output value is derived using a resistor ladder
with each end of the ladder tied to a positive and
negative voltage reference input source. If the voltage
of either input source fluctuates, a similar fluctuation will
result in the DAC output value.
The value of the individual resistors within the ladder
can be found in the applicable Electrical Specifications
chapter.
17.3 DAC Voltage Reference Output
The DAC can be output to the DACOUT pin by setting
the DACOE bit of the DACCON0 register to ‘1’.
Selecting the DAC reference voltage for output on the
DACOUT pin automatically overrides the digital output
buffer and digital input threshold detector functions of
that pin. Reading the DACOUT pin when it has been
configured for DAC reference voltage output will
always return a ‘0’.
Due to the limited current drive capability, a buffer must
be used on the DAC voltage reference output for
external connections to DACOUT. Figure 17-2 shows
an example buffering technique.
IF DACEN = 1
IF DACEN = 0 & DACLPS = 1 & DACR[4:0] = 11111
VOUT VSOURCE +=
IF DACEN = 0 & DACLPS = 0 & DACR[4:0] = 00000
VOUT VSOURCE =
VSOURCE+ = VDD, VREF, or FVR BUFFER 2
VSOURCE- = VSS
VOUT VSOURCE+VSOURCE-
DACR 4:0
25
-----------------------------


VSOURCE-+=
PIC16(L)F1934/6/7
DS41364E-page 174 2008-2011 Microchip Technology Inc.
FIGURE 17-1: DIGITAL-TO-ANALOG CONVERTER BLOCK DIAGRAM
FIGURE 17-2: VOLTAGE REFERENCE OUTPUT BUFFER EXAMPLE
32-to-1 MUX
DACR<4:0>
R
VREF-
DACNSS
R
R
R
R
R
R
32 DAC
DACOUT
5
(To Comparator, CPS and
ADC Modules)
DACOE
VDD
VREF+
DACPSS<1:0> 2
DACEN
Steps
Digital -t o-Analog Conve r ter (DAC)
FVR BUFFER2
R
VSOURCE-
VSOURCE+
VSS
DACLPS
DACOUT Buffered DAC Output
+
DAC
Module
Voltage
Reference
Output
Impedance
R
PIC® MCU
2008-2011 Microchip Technology Inc. DS41364E-page 175
PIC16(L)F1934/6/7
17.4 Low-P ow er Voltage State
In order for the DAC module to consume the least
amount of power, one of the two voltage reference input
sources to the resistor ladder must be disconnected.
Either the positive voltage source, (VSOURCE+), or the
negative voltage source, (VSOURCE-) can be disabled.
The negative voltage source is disabled by setting the
DACLPS bit in the DACCON0 register. Clearing the
DACLPS bit in the DACCON0 register disables the
positive voltage source.
17.4.1 OUTPUT CLAMPED TO POSITIVE
VOLTAGE SOURCE
The DAC output voltage can be set to VSOURCE+ with
the least amount of power consumption by performing
the following:
Clearing the DACEN bit in the DACCON0 register.
Setting the DACLPS bit in the DACCON0 register.
Configuring the DACPSS bits to the proper
positive source.
Configuring the DACR<4:0> bits to ‘11111’ in the
DACCON1 register.
This is also the method used to output the voltage level
from the FVR to an output pin. See Section 17.5
“Operation During Sle e p” for more information.
Reference Figure 17-3 for output clamping examples.
17.4.2 OUTPUT CLAMPED TO NEGATIVE
VOLTAGE SOURCE
The DAC output voltage can be set to VSOURCE- with
the least amount of power consumption by performing
the following:
Clearing the DACEN bit in the DACCON0 register.
Clearing the DACLPS bit in the DACCON0 register.
Configuring the DACNSS bits to the proper
negative source.
Configuring the DACR<4:0> bits to ‘00000’ in the
DACCON1 register.
This allows the comparator to detect a zero-crossing
while not consuming additional current through the DAC
module.
Reference Figure 17-3 for output clamping examples.
FIGURE 17-3: O UTPUT VOLTAGE CLAMPING EXAMPLES
17.5 Operation During Sleep
When the device wakes up from Sleep through an
interrupt or a Watchdog Timer time-out, the contents of
the DACCON0 register are not affected. To minimize
current consumption in Sleep mode, the voltage
reference should be disabled.
17.6 Effects of a Reset
A device Reset affects the following:
DAC is disabled.
DAC output voltage is removed from the
DACOUT pin.
The DACR<4:0> range select bits are cleared.
R
R
R
DAC Voltage Ladder
(see Figure 17-1)
VSOURCE+
DACEN = 0
DACLPS = 1
DACR<4:0> = 11111
VSOURCE-
R
R
R
DAC Voltage Ladder
(see Figure 17-1)
VSOURCE+
DACEN = 0
DACLPS = 0
DACR<4:0> = 00000
VSOURCE-
Output Clamped to Posit ive Voltage Source Output Clamped to Negati ve Voltage Source
PIC16(L)F1934/6/7
DS41364E-page 176 2008-2011 Microchip Technology Inc.
TABLE 17-1: SUMMARY OF REGISTERS ASSOCIATED WITH THE DAC MODULE
REGISTER 17-1: DACCON0: VOLTAGE REFERENCE CONTROL REGISTER 0
R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 U-0 R/W-0/0
DACEN DACLPS DACOE DACPSS<1:0> DACNSS
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 DACEN: DAC Enable bit
1 = DAC is enabled
0 = DAC is disabled
bit 6 DACLPS: DAC Low-Power Voltage State Select bit
1 = DAC Positive reference source selected
0 = DAC Negative reference source selected
bit 5 DACOE: DAC Voltage Output Enable bit
1 = DAC voltage level is also an output on the DACOUT pin
0 = DAC voltage level is disconnected from the DACOUT pin
bit 4 Unimplemented: Read as ‘0
bit 3-2 DACPSS<1:0>: DAC Positive Source Select bits
00 =V
DD
01 =VREF+ pin
10 = FVR Buffer2 output
11 = Reserved, do not use
bit 1 Unimplemented: Read as ‘0
bit 0 DACNSS: DAC Negative Source Select bits
1 =V
REF-
0 =V
SS
REGISTER 17-2: DACCON1: VOLTAGE REFERENCE CONTROL REGISTER 1
U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
DACR<4:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-5 Unimplemented: Read as ‘0
bit 4-0 DACR<4:0>: DAC Voltage Output Select bits
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on page
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 156
DACCON0 DACEN DACLPS DACOE DACPSS<1:0> DACNSS 176
DACCON1 DACR<4:0> 176
Legend: = Unimplemented location, read as 0’. Shaded cells are not used with the DAC Module.
2008-2011 Microchip Technology Inc. DS41364E-page 177
PIC16(L)F1934/6/7
18.0 COMPARATOR MODULE
Comparators are used to interface analog circuits to a
digital circuit by comparing two analog voltages and
providing a digital indication of their relative magnitudes.
Comparators are very useful mixed signal building
blocks because they provide analog functionality
independent of program execution. The analog
comparator module includes the following features:
Independent comparator control
Programmable input selection
Comparator output is available internally/externally
Programmable output polarity
Interrupt-on-change
Wake-up from Sleep
Programmable Speed/Power optimization
•PWM shutdown
Programmable and fixed voltage reference
18.1 Comparator Overview
A single comparator is shown in Figure 18-1 along with
the relationship between the analog input levels and
the digital output. When the analog voltage at VIN+ is
less than the analog voltage at VIN-, the output of the
comparator is a digital low level. When the analog
voltage at VIN+ is greater than the analog voltage at
VIN-, the output of the comparator is a digital high level.
FIGURE 18-1: SINGLE COMPARATOR
+
VIN+
VIN-Output
Output
VIN+
VIN-
Note: The black areas of the output of the
comparator represents the uncertainty
due to input offsets and response time.
PIC16(L)F1934/6/7
DS41364E-page 178 2008-2011 Microchip Technology Inc.
FIGU RE 18 -2: COMP ARA TOR MO DUL E SIMPL IFI ED BLOC K DIAG RAM
Note 1: When CxON = 0, the Comparator will produce a ‘0’ at the output.
2: When CxON = 0, all multiplexer inputs are disconnected.
3: Output of comparator can be frozen during debugging.
MUX
Cx(3)
0
1
2
3
CxON(1)
CxNCH<1:0>
2
0
1
CXPCH<1:0>
C12IN1-
C12IN2-
C12IN3-
CXIN+
MUX
-
+
CxVN
CxVP
CXOUT
To ECCP PWM Logic
Q1
D
EN
Q
CXPOL
MCXOUT
Set CxIF
0
1
CXSYNC CXOE
CXOUT
DQ
SYNCCXOUT
DAC
FVR Buffer2
C12IN0-
2
CxSP
CxHYS
det
Interrupt
det
Interrupt
To Timer1 or SR Latch
CxINTN
CxINTP
To D ata Bu s
2
3
VSS TRIS bit
CxON
(2)
(2)
(from Timer1)
T1CLK
2008-2011 Microchip Technology Inc. DS41364E-page 179
PIC16(L)F1934/6/7
18.2 Comparator Control
Each comparator has 2 control registers: CMxCON0 and
CMxCON1.
The CMxCON0 registers (see Register 18-1) contain
Control and Status bits for the following:
Enable
•Output selection
Output polarity
Speed/Power selection
Hysteresis enable
Output synchronization
The CMxCON1 registers (see Register 18-2) contain
Control bits for the following:
Interrupt enable
Interrupt edge polarity
Positive input channel selection
Negative input channel selection
18.2.1 COMPARATOR ENABLE
Setting the CxON bit of the CMxCON0 register enables
the comparator for operation. Clearing the CxON bit
disables the comparator resulting in minimum current
consumption.
18.2.2 COMPARATOR OUTPUT
SELECTION
The output of the comparator can be monitored by
reading either the CxOUT bit of the CMxCON0 register
or the MCxOUT bit of the CMOUT register. In order to
make the output available for an external connection,
the following conditions must be true:
CxOE bit of the CMxCON0 register must be set
Corresponding TRIS bit must be cleared
CxON bit of the CMxCON0 register must be set
18.2.3 COMPARATOR OUTPUT POLARITY
Inverting the output of the comparator is functionally
equivalent to swapping the comparator inputs. The
polarity of the comparator output can be inverted by
setting the CxPOL bit of the CMxCON0 register.
Clearing the CxPOL bit results in a non-inverted output.
Table 18-1 shows the output state versus input
conditions, including polarity control.
18.2.4 COMPARATOR SPEED/POWER
SELECTION
The trade-off between speed or power can be opti-
mized during program execution with the CxSP control
bit. The default state for this bit is ‘1’ which selects the
normal speed mode. Device power consumption can
be optimized at the cost of slower comparator propaga-
tion delay by clearing the CxSP bit to ‘0’.
Note 1: The CxOE bit of the CMxCON0 register
overrides the PORT data latch. Setting
the CxON bit of the CMxCON0 register
has no impact on the port override.
2: The internal output of the comparator is
latched with each instruction cycle.
Unless otherwise specified, external
outputs are not latched.
TABLE 18-1: COMPARATOR OUTPUT
STATE VS. IN PUT
CONDITIONS
Input Condition CxPOL CxOUT
CxVN > CxVP00
CxVN < CxVP01
CxVN > CxVP11
CxVN < CxVP10
PIC16(L)F1934/6/7
DS41364E-page 180 2008-2011 Microchip Technology Inc.
18.3 Comparator Hysteresis
A selectable amount of separation voltage can be
added to the input pins of each comparator to provide a
hysteresis function to the overall operation. Hysteresis
is enabled by setting the CxHYS bit of the CMxCON0
register.
See the applicable Electrical Specifications Chapter for
more information.
18.4 Timer1 Gate Operation
The output resulting from a comparator operation can
be used as a source for gate control of Timer1. See
Section 21.6 “Timer1 Gate” for more information.
This feature is useful for timing the duration or interval
of an analog event.
It is recommended that the comparator output be syn-
chronized to Timer1. This ensures that Timer1 does not
increment while a change in the comparator is occur-
ring.
18.4.1 COMPARATOR OUTPUT
SYNCHRONIZATION
The output from either comparator, C1 or C2, can be
synchronized with Timer1 by setting the CxSYNC bit of
the CMxCON0 register.
Once enabled, the comparator output is latched on the
falling edge of the Timer1 source clock. If a prescaler is
used with Timer1, the comparator output is latched after
the prescaling function. To prevent a race condition, the
comparator output is latched on the falling edge of the
Timer1 clock source and Timer1 increments on the
rising edge of its clock source. See the Comparator
Block Diagram (Figure 18-2) and the Timer1 Block
Diagram (Figure 22-1) for more information.
18.5 Comparator Interrupt
An interrupt can be generated upon a change in the
output value of the comparator for each comparator, a
rising edge detector and a falling edge detector are
present.
When either edge detector is triggered and its associ-
ated enable bit is set (CxINTP and/or CxINTN bits of
the CMxCON1 register), the Corresponding Interrupt
Flag bit (CxIF bit of the PIR2 register) will be set.
To enable the interrupt, you must set the following bits:
CxON, CxPOL and CxSP bits of the CMxCON0
register
CxIE bit of the PIE2 register
CxINTP bit of the CMxCON1 register (for a rising
edge detection)
CxINTN bit of the CMxCON1 register (for a falling
edge detection)
PEIE and GIE bits of the INTCON register
The associated interrupt flag bit, CxIF bit of the PIR2
register, must be cleared in software. If another edge is
detected while this flag is being cleared, the flag will still
be set at the end of the sequence.
18.6 Comparator Positive Input
Selection
Configuring the CxPCH<1:0> bits of the CMxCON1
register directs an internal voltage reference or an
analog pin to the non-inverting input of the comparator:
CxIN+ analog pin
•DAC
FVR (Fixed Voltage Reference)
•V
SS (Ground)
See Section 14.0 “Fixed Voltage Reference (FVR)”
for more information on the Fixed Voltage Reference
module.
See Section 17.0 “Digital-to-Analog Converter
(DAC) Module” for more information on the DAC input
signal.
Any time the comparator is disabled (CxON = 0), all
comparator inputs are disabled.
Note: Although a comparator is disabled, an
interrupt can be generated by changing
the output polarity with the CxPOL bit of
the CMxCON0 register, or by switching
the comparator on or off with the CxON bit
of the CMxCON0 register.
2008-2011 Microchip Technology Inc. DS41364E-page 181
PIC16(L)F1934/6/7
18.7 Comparator Negative Input
Selection
The CxNCH<1:0> bits of the CMxCON0 register direct
one of four analog pins to the comparator inverting
input.
18.8 Comparator Response Time
The comparator output is indeterminate for a period of
time after the change of an input source or the selection
of a new reference voltage. This period is referred to as
the response time. The response time of the comparator
differs from the settling time of the voltage reference.
Therefore, both of these times must be considered when
determining the total response time to a comparator
input change. See the Comparator and Voltage Refer-
ence Specifications in the applicable Electrical Specifi-
cations Chapter for more details.
18.9 Interaction with ECCP Logic
The C1 and C2 comparators can be used as general
purpose comparators. Their outputs can be brought
out to the C1OUT and C2OUT pins. When the ECCP
Auto-Shutdown is active it can use one or both
comparator signals. If auto-restart is also enabled, the
comparators can be configured as a closed loop
analog feedback to the ECCP, thereby, creating an
analog controlled PWM.
18.10 Analog Input Connection
Considerations
A simplified circuit for an analog input is shown in
Figure 18-3. Since the analog input pins share their
connection with a digital input, they have reverse
biased ESD protection diodes to VDD and VSS. The
analog input, therefore, must be between VSS and VDD.
If the input voltage deviates from this range by more
than 0.6V in either direction, one of the diodes is for-
ward biased and a latch-up may occur.
A maximum source impedance of 10 k is recommended
for the analog sources. Also, any external component
connected to an analog input pin, such as a capacitor or
a Zener diode, should have very little leakage current to
minimize inaccuracies introduced.
Note: To use CxIN+ and CxINx- pins as analog
input, the appropriate bits must be set in
the ANSEL register and the correspond-
ing TRIS bits must also be set to disable
the output drivers.
Note: When the comparator module is first
initialized the output state is unknown.
Upon initialization, the user should verify
the output state of the comparator prior to
relying on the result, primarily when using
the result in connection with other
peripheral features, such as the ECCP
Auto-Shutdown mode.
Note 1: When reading a PORT register, all pins
configured as analog inputs will read as a
0’. Pins configured as digital inputs will
convert as an analog input, according to
the input specification.
2: Analog levels on any pin defined as a
digital input, may cause the input buffer to
consume more current than is specified.
PIC16(L)F1934/6/7
DS41364E-page 182 2008-2011 Microchip Technology Inc.
FIGURE 18-3: ANALOG INPUT MODEL
VA
Rs < 10K
CPIN
5 pF
VDD
VT 0.6V
VT 0.6V
RIC
ILEAKAGE(1)
Vss
Legend: CPIN = Input Capacitance
ILEAKAGE = Leakage Current at the pin due to various junctions
RIC = Interconnect Resistance
RS= Source Impedance
VA= Analog Voltage
VT= Threshold Voltage
To Comparator
Note 1: See the applicable Electrical Specifications Chapter.
Analog
Input
pin
2008-2011 Microchip Technology Inc. DS41364E-page 183
PIC16(L)F1934/6/7
REGISTER 18-1: CMxCON0: COMPARATOR X CONTROL REGISTER 0
R/W-0/0 R-0/0 R/W-0/0 R/W-0/0 U-0 R/W-1/1 R/W-0/0 R/W-0/0
CxON CxOUT CxOE CxPOL CxSP CxHYS CxSYNC
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 CxON: Comparator Enable bit
1 = Comparator is enabled and consumes no active power
0 = Comparator is disabled
bit 6 CxOUT: Comparator Output bit
If CxPOL = 1 (inverted polarity):
1 = CxVP < CxVN
0 = CxVP > CxVN
If CxPOL = 0 (non-inverted polarity):
1 = CxVP > CxVN
0 = CxVP < CxVN
bit 5 CxOE: Comparator Output Enable bit
1 = CxOUT is present on the CxOUT pin. Requires that the associated TRIS bit be cleared to actually
drive the pin. Not affected by CxON.
0 = CxOUT is internal only
bit 4 CxPOL: Comparator Output Polarity Select bit
1 = Comparator output is inverted
0 = Comparator output is not inverted
bit 3 Unimplemented: Read as ‘0
bit 2 CxSP: Comparator Speed/Power Select bit
1 = Comparator operates in normal power, higher speed mode
0 = Comparator operates in low-power, low-speed mode
bit 1 CxHYS: Comparator Hysteresis Enable bit
1 = Comparator hysteresis enabled
0 = Comparator hysteresis disabled
bit 0 CxSYNC: Comparator Output Synchronous Mode bit
1 = Comparator output to Timer1 and I/O pin is synchronous to changes on Timer1 clock source.
Output updated on the falling edge of Timer1 clock source.
0 = Comparator output to Timer1 and I/O pin is asynchronous.
PIC16(L)F1934/6/7
DS41364E-page 184 2008-2011 Microchip Technology Inc.
REGISTER 18-2: CMxCON1: COMPARATOR CX CONTROL REGISTER 1
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0
CxINTP CxINTN CxPCH<1:0> CxNCH<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 CxINTP: Comparator Interrupt on Positive Going Edge Enable bits
1 = The CxIF interrupt flag will be set upon a positive going edge of the CxOUT bit
0 = No interrupt flag will be set on a positive going edge of the CxOUT bit
bit 6 CxINTN: Comparator Interrupt on Negative Going Edge Enable bits
1 = The CxIF interrupt flag will be set upon a negative going edge of the CxOUT bit
0 = No interrupt flag will be set on a negative going edge of the CxOUT bit
bit 5-4 CxPCH<1:0>: Comparator Positive Input Channel Select bits
00 = CxVP connects to CxIN+ pin
01 = CxVP connects to DAC Voltage Reference
10 = CxVP connects to FVR Voltage Reference
11 = CxVP connects to VSS
bit 3-2 Unimplemented: Read as0
bit 1-0 CxNCH<1:0>: Comparator Negative Input Channel Select bits
00 = CxVN connects to C12IN0- pin
01 = CxVN connects to C12IN1- pin
10 = CxVN connects to C12IN2- pin
11 = CxVN connects to C12IN3- pin
REGISTER 18-3: CMOUT: COMPARATOR OUTPUT REGISTER
U-0 U-0 U-0 U-0 U-0 U-0 R-0/0 R-0/0
MC2OUT MC1OUT
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-2 Unimplemented: Read as0
bit 1 MC2OUT: Mirror Copy of C2OUT bit
bit 0 MC1OUT: Mirror Copy of C1OUT bit
2008-2011 Microchip Technology Inc. DS41364E-page 185
PIC16(L)F1934/6/7
TABLE 18-2: SUMMARY OF REGISTERS ASSOCIATED WITH COMPARATOR MODULE
Name Bit 7 B it 6 B i t 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reg ister
on Page
CM1CON0 C1ON C1OUT C1OE C1POL --- C1SP C1HYS C1SYNC 183
CM2CON0 C2ON C2OUT C2OE C2POL C2SP C2HYS C2SYNC 183
CM1CON1 C1NTP C1INTN C1PCH<1:0> C1NCH<1:0> 184
CM2CON1 C2NTP C2INTN C2PCH<1:0> C2NCH<1:0> 184
CMOUT MC2OUT MC1OUT 184
FVRCON FVREN FVRRDY TSEN TSRNG CDAFVR<1:0> ADFVR<1:0> 156
DACCON0 DACEN DACLPS DACOE DACPSS<1:0> DACNSS 176
DACCON1 DACR<4:0> 176
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF 103
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
ANSELA ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 134
ANSELB ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 139
Legend: = unimplemented location, read as 0’. Shaded cells are unused by the comparator module.
PIC16(L)F1934/6/7
DS41364E-page 186 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 187
PIC16(L)F1934/6/7
19.0 SR LATCH
The module consists of a single SR Latch with multiple
Set and Reset inputs as well as separate latch outputs.
The SR Latch module includes the following features:
Programmable input selection
SR Latch output is available externally
Separate Q and Q outputs
Firmware Set and Reset
The SR Latch can be used in a variety of analog appli-
cations, including oscillator circuits, one-shot circuit,
hysteretic controllers, and analog timing applications.
19.1 Latch Operation
The latch is a Set-Reset Latch that does not depend on
a clock source. Each of the Set and Reset inputs are
active-high. The latch can be set or reset by:
Software control (SRPS and SRPR bits)
Comparator C1 output (SYNCC1OUT)
Comparator C2 output (SYNCC2OUT)
•SRI pin
Programmable clock (SRCLK)
The SRPS and the SRPR bits of the SRCON0 register
may be used to set or reset the SR Latch, respectively.
The latch is Reset-dominant. Therefore, if both Set and
Reset inputs are high, the latch will go to the Reset
state. Both the SRPS and SRPR bits are self resetting
which means that a single write to either of the bits is all
that is necessary to complete a latch Set or Reset oper-
ation.
The output from Comparator C1 or C2 can be used as
the Set or Reset inputs of the SR Latch. The output of
either Comparator can be synchronized to the Timer1
clock source. See Section 18.0 “Comparator Mod-
ule” and Section 21.0 “Timer1 Module with Gate
Control” for more information.
An external source on the SRI pin can be used as the
Set or Reset inputs of the SR Latch.
An internal clock source is available that can periodically
set or reset the SR Latch. The SRCLK<2:0> bits in the
SRCON0 register are used to select the clock source
period. The SRSCKE and SRRCKE bits of the SRCON1
register enable the clock source to set or reset the SR
Latch, respectively.
19.2 Latch Output
The SRQEN and SRNQEN bits of the SRCON0 regis-
ter control the Q and Q latch outputs. Both of the SR
Latch outputs may be directly output to an I/O pin at the
same time. The Q latch output pin function can be
moved to an alternate pin using the SRNQSEL bit of
the APFCON register.
The applicable TRIS bit of the corresponding port must
be cleared to enable the port pin output driver.
19.3 Effects of a Reset
Upon any device Reset, the SR Latch output is not ini-
tialized to a known state. The user’s firmware is
responsible for initializing the latch output before
enabling the output pins.
Note: Enabling both the Set and Reset inputs
from any one source at the same time
may result in indeterminate operation, as
the Reset dominance cannot be assured.
PIC16(L)F1934/6/7
DS41364E-page 188 2008-2011 Microchip Technology Inc.
FIGURE 19-1: SR LATCH SIMPLIFIED BLOCK DIAGRAM
SRPS
S
R
Q
Q
Note 1: If R = 1 and S = 1 simultaneously, Q = 0, Q =1
2: Pulse generator causes a 1 Q-state pulse width.
3: Name denotes the connection point at the comparator output.
Pulse
Gen(2)
SR
Latch(1)
SRQEN
SRSPE
SRSC2E
SRSCKE
SRCLK
SYNCC2OUT(3)
SRSC1E
SYNCC1OUT(3)
SRPR Pulse
Gen(2)
SRRPE
SRRC2E
SRRCKE
SRCLK
SYNCC2OUT(3)
SRRC1E
SYNCC1OUT(3)
SRLEN
SRNQEN
SRLEN
SRQ
SRNQ
SRI
SRI
2008-2011 Microchip Technology Inc. DS41364E-page 189
PIC16(L)F1934/6/7
TABLE 19-1: SRCLK FREQUENCY TABLE
SRCLK Divider FOSC = 32 MHz FOSC = 20 MHz FOSC = 16 MHz FOSC = 4 MHz FOSC = 1 MH z
111 512 62.5 kHz 39.0 kHz 31.3 kHz 7.81 kHz 1.95 kHz
110 256 125 kHz 78.1 kHz 62.5 kHz 15.6 kHz 3.90 kHz
101 128 250 kHz 156 kHz 125 kHz 31.25 kHz 7.81 kHz
100 64 500 kHz 313 kHz 250 kHz 62.5 kHz 15.6 kHz
011 32 1 MHz 625 kHz 500 kHz 125 kHz 31.3 kHz
010 16 2 MHz 1.25 MHz 1 MHz 250 kHz 62.5 kHz
001 8 4 MHz 2.5 MHz 2 MHz 500 kHz 125 kHz
000 4 8 MHz 5 MHz 4 MHz 1 MHz 250 kHz
REGISTER 19-1: SRCON0: SR LATCH CONTROL 0 REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/S-0/0 R/S-0/0
SRLEN SRCLK<2:0> SRQEN SRNQEN SRPS SRPR
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared S = Bit is set only
bit 7 SRLEN: SR Latch Enable bit
1 = SR Latch is enabled
0 = SR Latch is disabled
bit 6-4 SRCLK<2:0>: SR Latch Clock Divider bits
000 = Generates a 1 FOSC wide pulse every 4th FOSC cycle clock
001 = Generates a 1 FOSC wide pulse every 8th FOSC cycle clock
010 = Generates a 1 FOSC wide pulse every 16th FOSC cycle clock
011 = Generates a 1 FOSC wide pulse every 32nd FOSC cycle clock
100 = Generates a 1 FOSC wide pulse every 64th FOSC cycle clock
101 = Generates a 1 FOSC wide pulse every 128th FOSC cycle clock
110 = Generates a 1 FOSC wide pulse every 256th FOSC cycle clock
111 = Generates a 1 FOSC wide pulse every 512th FOSC cycle clock
bit 3 SRQEN: SR Latch Q Output Enable bit
If SRLEN = 1:
1 = Q is present on the SRQ pin
0 = External Q output is disabled
If SRLEN = 0:
SR Latch is disabled
bit 2 SRNQEN: SR Latch Q Output Enable bit
If SRLEN = 1:
1 =Q is present on the SRnQ pin
0 = External Q output is disabled
If SRLEN = 0:
SR Latch is disabled
bit 1 SRPS: Pulse Set Input of the SR Latch bit(1)
1 = Pulse set input for 1 Q-clock period
0 = No effect on set input.
bit 0 SRPR: Pulse Reset Input of the SR Latch bit(1)
1 = Pulse Reset input for 1 Q-clock period
0 = No effect on Reset input.
Note 1: Set only, always reads back ‘0’.
PIC16(L)F1934/6/7
DS41364E-page 190 2008-2011 Microchip Technology Inc.
TABLE 19-2: SUMMARY OF REGISTERS ASSOCIATED WITH SR LATCH MODULE
REGISTER 19-2: SRCON1: SR LATCH CONTROL 1 REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
SRSPE SRSCKE SRSC2E SRSC1E SRRPE SRRCKE SRRC2E SRRC1E
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 SRSPE: SR Latch Peripheral Set Enable bit
1 = SR Latch is set when the SRI pin is high.
0 = SRI pin has no effect on the set input of the SR Latch
bit 6 SRSCKE: SR Latch Set Clock Enable bit
1 = Set input of SR Latch is pulsed with SRCLK
0 = SRCLK has no effect on the set input of the SR Latch
bit 5 SRSC2E: SR Latch C2 Set Enable bit
1 = SR Latch is set when the C2 Comparator output is high
0 = C2 Comparator output has no effect on the set input of the SR Latch
bit 4 SRSC1E: SR Latch C1 Set Enable bit
1 = SR Latch is set when the C1 Comparator output is high
0 = C1 Comparator output has no effect on the set input of the SR Latch
bit 3 SRRPE: SR Latch Peripheral Reset Enable bit
1 = SR Latch is reset when the SRI pin is high.
0 = SRI pin has no effect on the reset input of the SR Latch
bit 2 SRRCKE: SR Latch Reset Clock Enable bit
1 = Reset input of SR Latch is pulsed with SRCLK
0 = SRCLK has no effect on the reset input of the SR Latch
bit 1 SRRC2E: SR Latch C2 Reset Enable bit
1 = SR Latch is reset when the C2 Comparator output is high
0 = C2 Comparator output has no effect on the reset input of the SR Latch
bit 0 SRRC1E: SR Latch C1 Reset Enable bit
1 = SR Latch is reset when the C1 Comparator output is high
0 = C1 Comparator output has no effect on the reset input of the SR Latch
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
ANSELA ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 134
SRCON0 SRLEN SRCLK<2:0> SRQEN SRNQEN SRPS SRPR 189
SRCON1 SRSPE SRSCKE SRSC2E SRSC1E SRRPE SRRCKE SRRC2E SRRC1E 190
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
Legend: — = unimplemented location, read as ‘0’. Shaded cells are unused by the SR Latch module.
2008-2011 Microchip Technology Inc. DS41364E-page 191
PIC16(L)F1934/6/7
20.0 TIMER0 MODULE
The Timer0 module is an 8-bit timer/counter with the
following features:
8-bit timer/counter register (TMR0)
8-bit prescaler (independent of Watchdog Timer)
Programmable internal or external clock source
Programmable external clock edge selection
Interrupt on overflow
TMR0 can be used to gate Timer1
Figure 20-1 is a block diagram of the Timer0 module.
20.1 Timer0 Operation
The Timer0 module can be used as either an 8-bit timer
or an 8-bit counter.
20.1.1 8-BIT TIMER MODE
The Timer0 module will increment every instruction
cycle, if used without a prescaler. 8-it Timer mode is
selected by clearing the TMR0CS bit of the
OPTION_REG register.
When TMR0 is written, the increment is inhibited for
two instruction cycles immediately following the write.
20.1.2 8-BIT COUNTER MODE
In 8-Bit Counter mode, the Timer0 module will increment
on every rising or falling edge of the T0CKI pin or the
Capacitive Sensing Oscillator (CPSCLK) signal.
8-Bit Counter mode using the T0CKI pin is selected by
setting the TMR0CS bit in the OPTION_REG register to
1’ and resetting the T0XCS bit in the CPSCON0 register
to ‘0’.
8-Bit Counter mode using the Capacitive Sensing
Oscillator (CPSCLK) signal is selected by setting the
TMR0CS bit in the OPTION_REG register to ‘1’ and
setting the T0XCS bit in the CPSCON0 register to ‘1’.
The rising or falling transition of the incrementing edge
for either input source is determined by the TMR0SE bit
in the OPTION_REG register.
FIGURE 20-1: BLOCK DIAGRAM OF THE TIMER0
Note: The value written to the TMR0 register
can be adjusted, in order to account for
the two instruction cycle delay when
TMR0 is written.
T0CKI
TMR0SE
TMR0
PS<2:0>
Data Bus
Set Flag bit TMR0IF
on Overflow
TMR0CS
0
1
0
18
8
8-bit
Prescaler
FOSC/4
PSA
Sync
2 TCY
Overflow to Timer1
1
0
From CPSCLK
T0XCS
PIC16(L)F1934/6/7
DS41364E-page 192 2008-2011 Microchip Technology Inc.
20.1.3 SOFTWARE PROGRAMMABLE
PRESCALER
A software programmable prescaler is available for
exclusive use with Timer0. The prescaler is enabled by
clearing the PSA bit of the OPTION_REG register.
There are 8 prescaler options for the Timer0 module
ranging from 1:2 to 1:256. The prescale values are
selectable via the PS<2:0> bits of the OPTION_REG
register. In order to have a 1:1 prescaler value for the
Timer0 module, the prescaler must be disabled by set-
ting the PSA bit of the OPTION_REG register.
The prescaler is not readable or writable. All instructions
writing to the TMR0 register will clear the prescaler.
20.1.4 TIMER0 INTERRUPT
Timer0 will generate an interrupt when the TMR0
register overflows from FFh to 00h. The TMR0IF
interrupt flag bit of the INTCON register is set every
time the TMR0 register overflows, regardless of
whether or not the Timer0 interrupt is enabled. The
TMR0IF bit can only be cleared in software. The Timer0
interrupt enable is the TMR0IE bit of the INTCON
register.
20.1.5 8-BIT COUNTER MODE
SYNCHRONIZATION
When in 8-Bit Counter mode, the incrementing edge on
the T0CKI pin must be synchronized to the instruction
clock. Synchronization can be accomplished by
sampling the prescaler output on the Q2 and Q4 cycles
of the instruction clock. The high and low periods of the
external clocking source must meet the timing
requirements as shown in the applicable Electrical
Specifications Chapter.
20.1.6 OPERATION DURING SLEEP
Timer0 cannot operate while the processor is in Sleep
mode. The contents of the TMR0 register will remain
unchanged while the processor is in Sleep mode.
Note: The Watchdog Timer (WDT) uses its own
independent prescaler.
Note: The Timer0 interrupt cannot wake the
processor from Sleep since the timer is
frozen during Sleep.
2008-2011 Microchip Technology Inc. DS41364E-page 193
PIC16(L)F1934/6/7
20.2 Option and Timer0 Control Register
TABLE 20-1: SUMMARY OF REGISTERS ASSOCIATED WITH TIMER0
REGISTER 20-1: OPTION_ RE G: OPTION REGISTER
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
WPUEN INTEDG TMR0CS TMR0SE PSA PS<2:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 WPUEN: Weak Pull-up Enable bit
1 = All weak pull-ups are disabled (except MCLR, if it is enabled)
0 = Weak pull-ups are enabled by individual WPUx latch values
bit 6 INTEDG: Interrupt Edge Select bit
1 = Interrupt on rising edge of INT pin
0 = Interrupt on falling edge of INT pin
bit 5 TMR0CS: Timer0 Clock Source Select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (FOSC/4)
bit 4 TMR0SE: Timer0 Source Edge Select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
bit 3 PSA: Prescaler Assignment bit
1 = Prescaler is not assigned to the Timer0 module
0 = Prescaler is assigned to the Timer0 module
bit 2-0 PS<2:0>: Prescaler Rate Select bits
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
CPSCON0 CPSON CPSRNG<1:0> CPSOUT T0XCS 323
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
OPTION_REG WPUEN INTEDG TMR0CS TMR0SE PSA PS<2:0> 193
TMR0 Timer0 Module Register 191*
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the Timer0 module.
* Page provides register information.
000
001
010
011
100
101
110
111
1 : 2
1 : 4
1 : 8
1 : 16
1 : 32
1 : 64
1 : 128
1 : 256
Bit Value Timer0 Rate
PIC16(L)F1934/6/7
DS41364E-page 194 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 195
PIC16(L)F1934/6/7
21.0 TIMER1 MODULE WITH GATE
CONTROL
The Timer1 module is a 16-bit timer/counter with the
following features:
16-bit timer/counter register pair (TMR1H:TMR1L)
Programmable internal or external clock source
2-bit prescaler
Dedicated 32 kHz oscillator circuit
Optionally synchronized comparator out
Multiple Timer1 gate (count enable) sources
Interrupt on overflow
Wake-up on overflow (external clock,
Asynchronous mode only)
Time base for the Capture/Compare function
Special Event Trigger (with CCP/ECCP)
Selectable Gate Source Polarity
Gate Toggle Mode
Gate Single-pulse Mode
Gate Value Status
Gate Event Interrupt
Figure 21-1 is a block diagram of the Timer1 module.
FIGURE 21-1: TIMER1 BLOCK DIAGRAM
TMR1H TMR1L
T1SYNC
T1CKPS<1:0>
Prescaler
1, 2, 4, 8
0
1
Synchronized
clock input
2
Set flag bit
TMR1IF on
Overflow TMR1(2)
TMR1ON
Note 1: ST Buffer is high speed type when using T1CKI.
2: Timer1 register increments on rising edge.
3: Synchronize does not operate while in Sleep.
T1G
T1OSC
FOSC/4
Internal
Clock
T1OSO
T1OSI
T1OSCEN
1
0
T1CKI
TMR1CS<1:0>
(1)
Synchronize(3)
det
Sleep input
TMR1GE
0
1
00
01
10
11
T1GPOL
D
Q
CK
Q
0
1
T1GVAL
T1GTM
Single Pulse
Acq. Control
T1GSPM
T1GGO/DONE
T1GSS<1:0>
EN
OUT
10
11
00
01
FOSC
Internal
Clock
Cap. Sensing
R
D
EN
Q
Q1
RD
T1GCON
Data Bus
det
Interrupt
TMR1GIF
Set
T1CLK
FOSC/2
Internal
Clock
D
EN
Q
T1G_IN
TMR1ON
Oscillator
From Timer0
Comparator 1
Overflow
Comparator 2
SYNCC2OUT
SYNCC1OUT
To Comparator Module
To LCD and Clock Switching Modules
PIC16(L)F1934/6/7
DS41364E-page 196 2008-2011 Microchip Technology Inc.
21.1 Timer1 Operation
The Timer1 module is a 16-bit incrementing counter
which is accessed through the TMR1H:TMR1L register
pair. Writes to TMR1H or TMR1L directly update the
counter.
When used with an internal clock source, the module is
a timer and increments on every instruction cycle.
When used with an external clock source, the module
can be used as either a timer or counter and incre-
ments on every selected edge of the external source.
Timer1 is enabled by configuring the TMR1ON and
TMR1GE bits in the T1CON and T1GCON registers,
respectively. Table 21-1 displays the Timer1 enable
selections.
21.2 Clock Source Selection
The TMR1CS<1:0> and T1OSCEN bits of the T1CON
register are used to select the clock source for Timer1.
Table 21-2 displays the clock source selections.
21.2.1 INTERNAL CLOCK SOURCE
When the internal clock source is selected the
TMR1H:TMR1L register pair will increment on multiples
of FOSC as determined by the Timer1 prescaler.
When the FOSC internal clock source is selected, the
Timer1 register value will increment by four counts every
instruction clock cycle. Due to this condition, a 2 LSB
error in resolution will occur when reading the Timer1
value. To utilize the full resolution of Timer1, an
asynchronous input signal must be used to gate the
Timer1 clock input.
The following asynchronous sources may be used:
Asynchronous event on the T1G pin to Timer1
gate
C1 or C2 comparator input to Timer1 gate
21.2.2 EXTERNAL CLOCK SOURCE
When the external clock source is selected, the Timer1
module may work as a timer or a counter.
When enabled to count, Timer1 is incremented on the
rising edge of the external clock input T1CKI or the
capacitive sensing oscillator signal. Either of these
external clock sources can be synchronized to the
microcontroller system clock or they can run
asynchronously.
When used as a timer with a clock oscillator, an
external 32.768 kHz crystal can be used in conjunction
with the dedicated internal oscillator circuit.
TABLE 21-1: TIMER1 ENABLE
SELECTIONS
TMR1ON TMR1GE Timer1
Operation
00Off
01Off
10Always On
11Count Enabled
Note: In Counter mode, a falling edge must be
registered by the counter prior to the first
incrementing rising edge after any one or
more of the following conditions:
Timer1 enabled after POR
Write to TMR1H or TMR1L
Timer1 is disabled
Timer1 is disabled (TMR1ON = 0)
when T1CKI is high then Timer1 is
enabled (TMR1ON=1) when T1CKI is
low.
TABLE 21-2: CLOCK SOURCE SELECTIONS
TMR1CS1 TMR1CS0 T1OSCEN Clock Source
00xInstruction Clock (FOSC/4)
01xSystem Clock (FOSC)
100External Clocking on T1CKI Pin
100External Clocking on T1CKI Pin
11xCapacitive Sensing Oscillator
2008-2011 Microchip Technology Inc. DS41364E-page 197
PIC16(L)F1934/6/7
21.3 Timer1 Prescaler
Timer1 has four prescaler options allowing 1, 2, 4 or 8
divisions of the clock input. The T1CKPS bits of the
T1CON register control the prescale counter. The
prescale counter is not directly readable or writable;
however, the prescaler counter is cleared upon a write to
TMR1H or TMR1L.
21.4 Timer1 Oscillator
A dedicated low-power 32.768 kHz oscillator circuit is
built-in between pins T1OSI (input) and T1OSO
(amplifier output). This internal circuit is to be used in
conjunction with an external 32.768 kHz crystal.
The oscillator circuit is enabled by setting the
T1OSCEN bit of the T1CON register. The oscillator will
continue to run during Sleep.
21.5 Timer1 Operation in
Asynchronous Counter Mode
If control bit T1SYNC of the T1CON register is set, the
external clock input is not synchronized. The timer
increments asynchronously to the internal phase
clocks. If the external clock source is selected then the
timer will continue to run during Sleep and can
generate an interrupt on overflow, which will wake-up
the processor. However, special precautions in
software are needed to read/write the timer (see
Section 21.5.1 “Reading and Writing Timer1 in
Asynchronous Counter Mode”).
21.5.1 READING AND WRITING TIMER1 IN
ASYNCHRONOUS COUNTER
MODE
Reading TMR1H or TMR1L while the timer is running
from an external asynchronous clock will ensure a valid
read (taken care of in hardware). However, the user
should keep in mind that reading the 16-bit timer in two
8-bit values itself, poses certain problems, since the
timer may overflow between the reads.
For writes, it is recommended that the user simply stop
the timer and write the desired values. A write
contention may occur by writing to the timer registers,
while the register is incrementing. This may produce an
unpredictable value in the TMR1H:TMR1L register pair.
21.6 Timer1 Gate
Timer1 can be configured to count freely or the count
can be enabled and disabled using Timer1 gate
circuitry. This is also referred to as Timer1 Gate Enable.
Timer1 gate can also be driven by multiple selectable
sources.
21.6.1 TIMER1 GATE ENABLE
The Timer1 Gate Enable mode is enabled by setting
the TMR1GE bit of the T1GCON register. The polarity
of the Timer1 Gate Enable mode is configured using
the T1GPOL bit of the T1GCON register.
When Timer1 Gate Enable mode is enabled, Timer1
will increment on the rising edge of the Timer1 clock
source. When Timer1 Gate Enable mode is disabled,
no incrementing will occur and Timer1 will hold the
current count. See Figure 21-3 for timing details.
Note: The oscillator requires a start-up and
stabilization time before use. Thus,
T1OSCEN should be set and a suitable
delay observed prior to using Timer1. A
suitable delay similar to the OST delay
can be implemented in software by
clearing the TMR1IF bit then presetting
the TMR1H:TMR1L register pair to
FC00h. The TMR1IF flag will be set when
1024 clock cycles have elapsed, thereby
indicating that the oscillator is running and
reasonably stable.
Note: When switching from synchronous to
asynchronous operation, it is possible to
skip an increment. When switching from
asynchronous to synchronous operation,
it is possible to produce an additional
increment.
TABLE 21-3: TIMER1 GATE ENABLE
SELECTIONS
T1CLK T1GPOL T1G Timer1 Operation
00Counts
01Holds Count
10Holds Count
11Counts
PIC16(L)F1934/6/7
DS41364E-page 198 2008-2011 Microchip Technology Inc.
21.6.2 TIMER1 GATE SOURCE
SELECTION
The Timer1 gate source can be selected from one of
four different sources. Source selection is controlled by
the T1GSS bits of the T1GCON register. The polarity
for each available source is also selectable. Polarity
selection is controlled by the T1GPOL bit of the
T1GCON register.
TABLE 21-4: TIMER1 GATE SOURCES
21.6.2.1 T1G Pin Gate Operation
The T1G pin is one source for Timer1 gate control. It
can be used to supply an external source to the Timer1
gate circuitry.
21.6.2.2 Timer0 Overflow Gate Operation
When Timer0 increments from FFh to 00h, a
low-to-high pulse will automatically be generated and
internally supplied to the Timer1 gate circuitry.
21.6.2.3 Comparator C1 Gate Operation
The output resulting from a Comparator 1 operation can
be selected as a source for Timer1 gate control. The
Comparator 1 output (SYNCC1OUT) can be
synchronized to the Timer1 clock or left asynchronous.
For more information see Section 18.4.1 “Comparator
Output Synchronization”.
21.6.2.4 Comparator C2 Gate Operation
The output resulting from a Comparator 2 operation
can be selected as a source for Timer1 gate control.
The Comparator 2 output (SYNCC2OUT) can be
synchronized to the Timer1 clock or left asynchronous.
For more information see Section 18.4.1 “Comparator
Output Synchronization”.
21.6.3 TIMER1 GATE TOGGLE MODE
When Timer1 Gate Toggle mode is enabled, it is possi-
ble to measure the full-cycle length of a Timer1 gate
signal, as opposed to the duration of a single level
pulse.
The Timer1 gate source is routed through a flip-flop that
changes state on every incrementing edge of the sig-
nal. See Figure 21-4 for timing details.
Timer1 Gate Toggle mode is enabled by setting the
T1GTM bit of the T1GCON register. When the T1GTM
bit is cleared, the flip-flop is cleared and held clear. This
is necessary in order to control which edge is
measured.
21.6.4 TIMER1 GATE SINGLE-PULSE
MODE
When Timer1 Gate Single-Pulse mode is enabled, it is
possible to capture a single pulse gate event. Timer1
Gate Single-Pulse mode is first enabled by setting the
T1GSPM bit in the T1GCON register. Next, the
T1GGO/DONE bit in the T1GCON register must be set.
The Timer1 will be fully enabled on the next
incrementing edge. On the next trailing edge of the
pulse, the T1GGO/DONE bit will automatically be
cleared. No other gate events will be allowed to
increment Timer1 until the T1GGO/DONE bit is once
again set in software. See Figure 21-5 for timing details.
If the Single Pulse Gate mode is disabled by clearing the
T1GSPM bit in the T1GCON register, the T1GGO/DONE
bit should also be cleared.
Enabling the Toggle mode and the Single-Pulse mode
simultaneously will permit both sections to work
together. This allows the cycle times on the Timer1 gate
source to be measured. See Figure 21-6 for timing
details.
21.6.5 TIMER1 GATE VALUE STATUS
When Timer1 Gate Value Status is utilized, it is possible
to read the most current level of the gate control value.
The value is stored in the T1GVAL bit in the T1GCON
register. The T1GVAL bit is valid even when the Timer1
gate is not enabled (TMR1GE bit is cleared).
21.6.6 TIMER1 GATE EVENT INTERRUPT
When Timer1 Gate Event Interrupt is enabled, it is pos-
sible to generate an interrupt upon the completion of a
gate event. When the falling edge of T1GVAL occurs,
the TMR1GIF flag bit in the PIR1 register will be set. If
the TMR1GIE bit in the PIE1 register is set, then an
interrupt will be recognized.
The TMR1GIF flag bit operates even when the Timer1
gate is not enabled (TMR1GE bit is cleared).
T1GSS Timer 1 Ga te Sour ce
00 Timer1 Gate Pin
01 Overflow of Timer0
(TMR0 increments from FFh to 00h)
10 Comparator 1 Output SYNCC1OUT
(optionally Timer1 synchronized output)
11 Comparator 2 Output SYNCC2OUT
(optionally Timer1 synchronized output)
Note: Enabling Toggle mode at the same time
as changing the gate polarity may result in
indeterminate operation.
2008-2011 Microchip Technology Inc. DS41364E-page 199
PIC16(L)F1934/6/7
21.7 Timer1 Interrupt
The Timer1 register pair (TMR1H:TMR1L) increments
to FFFFh and rolls over to 0000h. When Timer1 rolls
over, the Timer1 interrupt flag bit of the PIR1 register is
set. To enable the interrupt on rollover, you must set
these bits:
TMR1ON bit of the T1CON register
TMR1IE bit of the PIE1 register
PEIE bit of the INTCON register
GIE bit of the INTCON register
The interrupt is cleared by clearing the TMR1IF bit in
the Interrupt Service Routine.
21.8 Timer1 Operation During Sleep
Timer1 can only operate during Sleep when setup in
Asynchronous Counter mode. In this mode, an external
crystal or clock source can be used to increment the
counter. To set up the timer to wake the device:
TMR1ON bit of the T1CON register must be set
TMR1IE bit of the PIE1 register must be set
PEIE bit of the INTCON register must be set
T1SYNC bit of the T1CON register must be set
TMR1CS bits of the T1CON register must be
configured
T1OSCEN bit of the T1CON register must be
configured
The device will wake-up on an overflow and execute
the next instructions. If the GIE bit of the INTCON
register is set, the device will call the Interrupt Service
Routine.
Timer1 oscillator will continue to operate in Sleep
regardless of the T1SYNC bit setting.
21. 9 ECCP/CCP Cap ture/ Comp are Time
Base
The CCP modules use the TMR1H:TMR1L register
pair as the time base when operating in Capture or
Compare mode.
In Capture mode, the value in the TMR1H:TMR1L
register pair is copied into the CCPR1H:CCPR1L
register pair on a configured event.
In Compare mode, an event is triggered when the value
CCPR1H:CCPR1L register pair matches the value in
the TMR1H:TMR1L register pair. This event can be a
Special Event Trigger.
For more information, see Section 12.0 “I/O Ports”.
21.10 ECCP/CCP Special Event Trigger
When any of the CCP’s are configured to trigger a spe-
cial event, the trigger will clear the TMR1H:TMR1L reg-
ister pair. This special event does not cause a Timer1
interrupt. The CCP module may still be configured to
generate a CCP interrupt.
In this mode of operation, the CCPR1H:CCPR1L
register pair becomes the period register for Timer1.
Timer1 should be synchronized and FOSC/4 should be
selected as the clock source in order to utilize the Spe-
cial Event Trigger. Asynchronous operation of Timer1
can cause a Special Event Trigger to be missed.
In the event that a write to TMR1H or TMR1L coincides
with a Special Event Trigger from the CCP, the write will
take precedence.
For more information, see Section 15.2.5 “Special
Event Trigger”.
FIGURE 21-2: TIMER1 INCREMENTING EDGE
Note: The TMR1H:TMR1L register pair and the
TMR1IF bit should be cleared before
enabling interrupts.
T1CKI = 1
when TMR1
Enabled
T1CKI = 0
when TMR1
Enabled
Note 1: Arrows indicate counter increments.
2: In Counter mode, a falling edge must be registered by the counter prior to the first incrementing rising edge of the clock.
PIC16(L)F1934/6/7
DS41364E-page 200 2008-2011 Microchip Technology Inc.
FIGURE 21-3: TIMER1 GATE ENABLE MODE
FIGURE 21-4: TIMER1 GATE TOGGLE MODE
TMR1GE
T1GPOL
T1G_IN
T1CKI
T1GVAL
TIMER1 N N + 1 N + 2 N + 3 N + 4
TMR1GE
T1GPOL
T1GTM
T1G_IN
T1CKI
T1GVAL
TIMER1 N N + 1 N + 2 N + 3 N + 4 N + 5 N + 6 N + 7 N + 8
2008-2011 Microchip Technology Inc. DS41364E-page 201
PIC16(L)F1934/6/7
FIGURE 21-5: TIMER1 GATE SINGLE-PULSE MODE
TMR1GE
T1GPOL
T1G_IN
T1CKI
T1GVAL
TIMER1 N N + 1 N + 2
T1GSPM
T1GGO/
DONE
Set by software
Cleared by hardware on
falling edge of T1GVAL
Set by hardware on
falling edge of T1GVAL
Cleared by software
Cleared by
software
TMR1GIF
Counting enabled on
rising edge of T1G
PIC16(L)F1934/6/7
DS41364E-page 202 2008-2011 Microchip Technology Inc.
FIGURE 21-6: TIMER1 GATE SINGLE-PULSE AND TOGGLE COMBINED MODE
TMR1GE
T1GPOL
T1G_IN
T1CKI
T1GVAL
TIMER1 NN + 1
N + 2
T1GSPM
T1GGO/
DONE
Set by software
Cleared by hardware on
falling edge of T1GVAL
Set by hardware on
falling edge of T1GVAL
Cleared by software
Cleared by
software
TMR1GIF
T1GTM
Counting enabled on
rising edge of T1G
N + 4
N + 3
2008-2011 Microchip Technology Inc. DS41364E-page 203
PIC16(L)F1934/6/7
21.11 Timer1 Control Register
The Timer1 Control register (T1CON), shown in
Register 21-1, is used to control Timer1 and select the
various features of the Timer1 module.
REGISTER 21-1: T1CON: TIMER1 CONTROL REGISTER
R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W-0/u U-0 R/W-0/u
TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-6 TMR1CS<1:0>: Timer1 Clock Source Select bits
11 = Timer1 clock source is Capacitive Sensing Oscillator (CAPOSC)
10 = Timer1 clock source is pin or oscillator:
If T1OSCEN = 0:
External clock from T1CKI pin (on the rising edge)
If T1OSCEN = 1:
Crystal oscillator on T1OSI/T1OSO pins
01 = Timer1 clock source is system clock (FOSC)
00 = Timer1 clock source is instruction clock (FOSC/4)
bit 5-4 T1CKPS<1:0>: Timer1 Input Clock Prescale Select bits
11 = 1:8 Prescale value
10 = 1:4 Prescale value
01 = 1:2 Prescale value
00 = 1:1 Prescale value
bit 3 T1OSCEN: LP Oscillator Enable Control bit
1 = Dedicated Timer1 oscillator circuit enabled
0 = Dedicated Timer1 oscillator circuit disabled
bit 2 T1SYNC: Timer1 External Clock Input Synchronization Control bit
TMR1CS<1:0> = 1X
1 = Do not synchronize external clock input
0 = Synchronize external clock input with system clock (FOSC)
TMR1CS<1:0> = 0X
This bit is ignored. Timer1 uses the internal clock when TMR1CS<1:0> = 1X.
bit 1 Unimplemented: Read as ‘0
bit 0 TMR1ON: Timer1 On bit
1 = Enables Timer1
0 = Stops Timer1
Clears Timer1 gate flip-flop
PIC16(L)F1934/6/7
DS41364E-page 204 2008-2011 Microchip Technology Inc.
21.12 Timer1 Gate Control Register
The Timer1 Gate Control register (T1GCON), shown in
Register 21-2, is used to control Timer1 gate.
REGISTER 21-2: T1GCON: TIMER1 GATE CONTROL REGISTER
R/W-0/u R/W-0/u R/W-0/u R/W-0/u R/W/HC-0/u R-x/x R/W-0/u R/W-0/u
TMR1GE T1GPOL T1GTM T1GSPM T1GGO/
DONE
T1GVAL T1GSS<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Bit is cleared by hardware
bit 7 TMR1GE: Timer1 Gate Enable bit
If TMR1ON = 0:
This bit is ignored
If TMR1ON = 1:
1 = Timer1 counting is controlled by the Timer1 gate function
0 = Timer1 counts regardless of Timer1 gate function
bit 6 T1GPOL: Timer1 Gate Polarity bit
1 = Timer1 gate is active-high (Timer1 counts when gate is high)
0 = Timer1 gate is active-low (Timer1 counts when gate is low)
bit 5 T1GTM: Timer1 Gate Toggle Mode bit
1 = Timer1 Gate Toggle mode is enabled
0 = Timer1 Gate Toggle mode is disabled and toggle flip flop is cleared
Timer1 gate flip-flop toggles on every rising edge.
bit 4 T1GSPM: Timer1 Gate Single-Pulse Mode bit
1 = Timer1 gate Single-Pulse mode is enabled and is controlling Timer1 gate
0 = Timer1 gate Single-Pulse mode is disabled
bit 3 T1GGO/DONE: Timer1 Gate Single-Pulse Acquisition Status bit
1 = Timer1 gate single-pulse acquisition is ready, waiting for an edge
0 = Timer1 gate single-pulse acquisition has completed or has not been started
bit 2 T1GVAL: Timer1 Gate Current State bit
Indicates the current state of the Timer1 gate that could be provided to TMR1H:TMR1L.
Unaffected by Timer1 Gate Enable (TMR1GE).
bit 1-0 T1GSS<1:0>: Timer1 Gate Source Select bits
00 = Timer1 gate pin
01 = Timer0 overflow output
10 = Comparator 1 optionally synchronized output (SYNCC1OUT)
11 = Comparator 2 optionally synchronized output (SYNCC2OUT)
2008-2011 Microchip Technology Inc. DS41364E-page 205
PIC16(L)F1934/6/7
TABLE 21-5: SUMMARY OF REGISTERS ASSOCIATED WITH TIMER1
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
ANSELB —ANSB5ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 139
CCP1CON P1M<1:0> DC1B<1:0> CCP1M<3:0> 234
CCP2CON P2M<1:0> DC2B<1:0> CCP2M<3:0> 234
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register 199*
TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register 199*
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON203
T1GCON TMR1GE T1GPOL T1GTM T1GSPM T1GGO/
DONE
T1GVAL T1GSS<1:0> 204
Legend: = unimplemented location, read as 0’. Shaded cells are not used by the Timer1 module.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 206 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 207
PIC16(L)F1934/6/7
22.0 TIMER2/4/6 M ODULES
There are up to three identical Timer2-type modules
available. To maintain pre-existing naming conventions,
the Timers are called Timer2, Timer4 and Timer6 (also
Timer2/4/6).
The Timer2/4/6 modules incorporate the following
features:
8-bit Timer and Period registers (TMRx and PRx,
respectively)
Readable and writable (both registers)
Software programmable prescaler (1:1, 1:4, 1:16,
and 1:64)
Software programmable postscaler (1:1 to 1:16)
Interrupt on TMRx match with PRx, respectively
Optional use as the shift clock for the MSSP
modules (Timer2 only)
See Figure 22-1 for a block diagram of Timer2/4/6.
FIGURE 22-1: TIMER2/4/6 BLOCK DIAGRAM
Note: The ‘x’ variable used in this section is
used to designate Timer2, Timer4, or
Timer6. For example, TxCON references
T2CON, T4CON, or T6CON. PRx refer-
ences PR2, PR4, or PR6.
Comparator
TMRx Sets Flag
TMRx
Output
Reset
Postscaler
Prescaler
PRx
2
FOSC/4
1:1 to 1:16
1:1, 1:4, 1:16, 1:64
EQ
4
bit TMRxIF
TxOUTPS<3:0>
TxCKPS<1:0>
PIC16(L)F1934/6/7
DS41364E-page 208 2008-2011 Microchip Technology Inc.
22.1 Timer2/4/6 Operation
The clock input to the Timer2/4/6 modules is the
system instruction clock (FOSC/4).
TMRx increments from 00h on each clock edge.
A 4-bit counter/prescaler on the clock input allows direct
input, divide-by-4 and divide-by-16 prescale options.
These options are selected by the prescaler control bits,
TxCKPS<1:0> of the TxCON register. The value of
TMRx is compared to that of the Period register, PRx, on
each clock cycle. When the two values match, the
comparator generates a match signal as the timer
output. This signal also resets the value of TMRx to 00h
on the next cycle and drives the output
counter/postscaler (see Section 22.2 “Timer2/4/6
Interrupt”).
The TMRx and PRx registers are both directly readable
and writable. The TMRx register is cleared on any
device Reset, whereas the PRx register initializes to
FFh. Both the prescaler and postscaler counters are
cleared on the following events:
a write to the TMRx register
a write to the TxCON register
Power-on Reset (POR)
Brown-out Reset (BOR)
•MCLR
Reset
Watchdog Timer (WDT) Reset
Stack Overflow Reset
Stack Underflow Reset
RESET Instruction
22.2 Timer2/4/6 Interrupt
Timer2/4/6 can also generate an optional device
interrupt. The Timer2/4/6 output signal (TMRx-to-PRx
match) provides the input for the 4-bit
counter/postscaler. This counter generates the TMRx
match interrupt flag which is latched in TMRxIF of the
PIRx register. The interrupt is enabled by setting the
TMRx Match Interrupt Enable bit, TMRxIE, of the PIEx
register.
A range of 16 postscale options (from 1:1 through 1:16
inclusive) can be selected with the postscaler control
bits, TxOUTPS<3:0>, of the TxCON register.
22.3 Timer2/4/6 Output
The unscaled output of TMRx is available primarily to
the CCP modules, where it is used as a time base for
operations in PWM mode.
Timer2 can be optionally used as the shift clock source
for the MSSP module operating in SPI mode.
Additional information is provided in Section 24.0
“Master Synchronous Serial Port Module”
22.4 Timer2/4/6 Operation During Sleep
The Timer2/4/6 timers cannot be operated while the
processor is in Sleep mode. The contents of the TMRx
and PRx registers will remain unchanged while the
processor is in Sleep mode.
Note: TMRx is not cleared when TxCON is
written.
2008-2011 Microchip Technology Inc. DS41364E-page 209
PIC16(L)F1934/6/7
22.5 Timer2/4/6 Control Register
REGISTER 22-1: TXCON: TIMER2/TIMER4/TIMER6 CONTROL REGISTER
U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
TOUTPS<3:0> TMRxON TxCKPS<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 Unimplemented: Read as ‘0
bit 6-3 TOUTPS<3:0>: Timer Output Postscaler Select bits
0000 = 1:1 Postscaler
0001 = 1:2 Postscaler
0010 = 1:3 Postscaler
0011 = 1:4 Postscaler
0100 = 1:5 Postscaler
0101 = 1:6 Postscaler
0110 = 1:7 Postscaler
0111 = 1:8 Postscaler
1000 = 1:9 Postscaler
1001 = 1:10 Postscaler
1010 = 1:11 Postscaler
1011 = 1:12 Postscaler
1100 = 1:13 Postscaler
1101 = 1:14 Postscaler
1110 = 1:15 Postscaler
1111 = 1:16 Postscaler
bit 2 TMRxON: Timerx On bit
1 =Timerx is on
0 =Timerx is off
bit 1-0 TxCKPS<1:0>: Timer2-type Clock Prescale Select bits
00 = Prescaler is 1
01 = Prescaler is 4
10 = Prescaler is 16
11 = Prescaler is 64
PIC16(L)F1934/6/7
DS41364E-page 210 2008-2011 Microchip Technology Inc.
TABLE 22-1: SUMMARY OF REGISTERS ASSOCIATED WITH TIMER2/4/6
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
CCP2CON P2M<1:0> DC2B<1:0> CCP2M<3:0> 234
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE —TMR4IE101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF —TMR4IF 104
PR2 Timer2 Module Period Register 207*
PR4 Timer4 Module Period Register 207*
PR6 Timer6 Module Period Register 207*
T2CON TOUTPS<3:0> TMR2ON T2CKPS<1:0> 209
T4CON TOUTPS<3:0> TMR4ON T4CKPS<1:0> 209
T6CON TOUTPS<3:0> TMR2ON T6CKPS<1:0> 209
TMR2 Holding Register for the 8-bit TMR2 Register 207*
TMR4 Holding Register for the 8-bit TMR4 Register(1) 207*
TMR6 Holding Register for the 8-bit TMR6 Register(1) 207*
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used for Timer2 module.
* Page provides register information.
2008-2011 Microchip Technology Inc. DS41364E-page 211
PIC16(L)F1934/6/7
23.0 CAPTURE/COMPARE/PWM
MODULES
The Capture/Compare/PWM module is a peripheral
which allows the user to time and control different
events, and to generate Pulse-Width Modulation
(PWM) signals. In Capture mode, the peripheral allows
the timing of the duration of an event. The Compare
mode allows the user to trigger an external event when
a predetermined amount of time has expired. The
PWM mode can generate Pulse-Width Modulated
signals of varying frequency and duty cycle.
This family of devices contains three Enhanced
Capture/Compare/PWM modules (ECCP1, ECCP2,
and ECCP3) and two standard Capture/Compare/PWM
modules (CCP4 and CCP5).
The Capture and Compare functions are identical for all
five CCP modules (ECCP1, ECCP2, ECCP3, CCP4,
and CCP5). The only differences between CCP
modules are in the Pulse-Width Modulation (PWM)
function. The standard PWM function is identical in
modules, CCP4 and CCP5. In CCP modules ECCP1,
ECCP2, and ECCP3, the Enhanced PWM function has
slight variations from one another. Full-Bridge ECCP
modules have four available I/O pins while Half-Bridge
ECCP modules only have two available I/O pins. See
Table 23-1 for more information.
Note 1: In devices with more than one CCP
module, it is very important to pay close
attention to the register names used. A
number placed after the module acronym
is used to distinguish between separate
modules. For example, the CCP1CON
and CCP2CON control the same
operational aspects of two completely
different CCP modules.
2: Throughout this section, generic
references to a CCP module in any of its
operating modes may be interpreted as
being equally applicable to ECCP1,
ECCP2, ECCP3, CCP4 and CCP5.
Register names, module signals, I/O pins,
and bit names may use the generic
designator ‘x’ to indicate the use of a
numeral to distinguish a particular module,
when required.
TABLE 23-1: PWM RESOURCES
Device Name ECCP1 ECCP2 ECCP3 CCP4 CCP5
PIC16(L)F1936 Enhanced PWM
Full-Bridge
Enhanced PWM
Half-Bridge
Enhanced PWM
Half-Bridge Standard PWM Standard PWM
PIC16(L)F1934/7 Enhanced PWM
Full-Bridge
Enhanced PWM
Full-Bridge
Enhanced PWM
Half-Bridge Standard PWM Standard PWM
PIC16(L)F1934/6/7
DS41364E-page 212 2008-2011 Microchip Technology Inc.
23.1 Capture Mode
The Capture mode function described in this section is
available and identical for CCP modules ECCP1,
ECCP2, ECCP3, CCP4 and CCP5.
Capture mode makes use of the 16-bit Timer1
resource. When an event occurs on the CCPx pin, the
16-bit CCPRxH:CCPRxL register pair captures and
stores the 16-bit value of the TMR1H:TMR1L register
pair, respectively. An event is defined as one of the
following and is configured by the CCPxM<3:0> bits of
the CCPxCON register:
Every falling edge
Every rising edge
Every 4th rising edge
Every 16th rising edge
When a capture is made, the Interrupt Request Flag bit
CCPxIF of the PIRx register is set. The interrupt flag
must be cleared in software. If another capture occurs
before the value in the CCPRxH, CCPRxL register pair
is read, the old captured value is overwritten by the new
captured value.
Figure 23-1 shows a simplified diagram of the Capture
operation.
23.1.1 CCP PIN CONFIGURATION
In Capture mode, the CCPx pin should be configured
as an input by setting the associated TRIS control bit.
Also, the CCPx pin function can be moved to
alternative pins using the APFCON register. Refer to
Section 12.1 “Alternate Pin Function for more
details.
FIGURE 23-1: CAPTURE MODE
OPERATION BLOCK
DIAGRAM
23.1.2 TIMER1 MODE RESOURCE
Timer1 must be running in Timer mode or Synchronized
Counter mode for the CCP module to use the capture
feature. In Asynchronous Counter mode, the capture
operation may not work.
See Section 21.0 “Timer1 Module w ith Gate Control”
for more information on configuring Timer1.
23.1.3 SOFTWARE INTERRUPT MODE
When the Capture mode is changed, a false capture
interrupt may be generated. The user should keep the
CCPxIE interrupt enable bit of the PIEx register clear to
avoid false interrupts. Additionally, the user should
clear the CCPxIF interrupt flag bit of the PIRx register
following any change in Operating mode.
23.1.4 CCP PRESCALER
There are four prescaler settings specified by the
CCPxM<3:0> bits of the CCPxCON register. Whenever
the CCP module is turned off, or the CCP module is not
in Capture mode, the prescaler counter is cleared. Any
Reset will clear the prescaler counter.
Switching from one capture prescaler to another does
not clear the prescaler and may generate a false
interrupt. To avoid this unexpected operation, turn the
module off by clearing the CCPxCON register before
changing the prescaler. Example 23-1 demonstrates
the code to perform this function.
EXAMPLE 23-1: CHANGIN G BETWEEN
CAPTURE PRESCALERS
23.1.5 CAPTURE DURING SLEEP
Capture mode depends upon the Timer1 module for
proper operation. There are two options for driving the
Timer1 module in Capture mode. It can be driven by the
instruction clock (FOSC/4), or by an external clock source.
When Timer1 is clocked by FOSC/4, Timer1 will not
increment during Sleep. When the device wakes from
Sleep, Timer1 will continue from its previous state.
Capture mode will operate during Sleep when Timer1
is clocked by an external clock source.
Note: If the CCPx pin is configured as an output,
a write to the port can cause a capture
condition.
CCPRxH CCPRxL
TMR1H TMR1L
Set Flag bit CCPxIF
(PIRx register)
Capture
Enable
CCPxM<3:0>
Prescaler
1, 4, 16
and
Edge Detect
pin
CCPx
System Clock (FOSC)
Note: Clocking Timer1 from the system clock
(FOSC) should not be used in Capture
mode. In order for Capture mode to
recognize the trigger event on the CCPx
pin, Timer1 must be clocked from the
instruction clock (FOSC/4) or from an
external clock source.
BANKSEL CCPxCON ;Set Bank bits to point
;to CCPxCON
CLRF CCPxCON ;Turn CCP module off
MOVLW NEW_CAPT_PS ;Load the W reg with
;the new prescaler
;move value and CCP ON
MOVWF CCPxCON ;Load CCPxCON with this
;value
2008-2011 Microchip Technology Inc. DS41364E-page 213
PIC16(L)F1934/6/7
23.1.6 ALTERNATE PIN LOCATIONS
This module incorporates I/O pins that can be moved to
other locations with the use of the alternate pin function
register, APFCON. To determine which pins can be
moved and what their default locations are upon a
Reset, see Secti on 12.1 “Al ternate Pin Function” for
more information.
TABLE 23-2: SUMMARY OF REGISTERS ASSOCIATED WITH CAPTURE
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
APFCON CCP3SEL T1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL 131
CCPxCON PxM<1:0>(1) DCxB<1:0> CCPxM<3:0> 234
CCPRxL Capture/Compare/PWM Register x Low Byte (LSB) 212
CCPRxH Capture/Compare/PWM Register x High Byte (MSB) 212
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE TMR4IE 101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF —CCP2IF
103
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF TMR4IF 104
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON
203
T1GCON TMR1GE T1GPOL T1GTM T1GSPM T1GGO/DONE T1GVAL T1GSS<1:0> 204
TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register 199
TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register 199
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TRISD(2) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 145
TRISE ———— (3) TRISE2(2) TRISE1(2) TRISE0(2) 148
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by Capture mode.
Note 1: Applies to ECCP modules only.
2: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
3: Unimplemented, read as 1’.
PIC16(L)F1934/6/7
DS41364E-page 214 2008-2011 Microchip Technology Inc.
23.2 Compare Mode
The Compare mode function described in this section
is available and identical for CCP modules ECCP1,
ECCP2, ECCP3, CCP4 and CCP5.
Compare mode makes use of the 16-bit Timer1
resource. The 16-bit value of the CCPRxH:CCPRxL
register pair is constantly compared against the 16-bit
value of the TMR1H:TMR1L register pair. When a
match occurs, one of the following events can occur:
Toggle the CCPx output
Set the CCPx output
Clear the CCPx output
Generate a Special Event Trigger
Generate a Software Interrupt
The action on the pin is based on the value of the
CCPxM<3:0> control bits of the CCPxCON register. At
the same time, the interrupt flag CCPxIF bit is set.
All Compare modes can generate an interrupt.
Figure 23-2 shows a simplified diagram of the
Compare operation.
FIGUR E 2 3-2: COMPARE MODE
OPERATION BLOCK
DIAGRAM
23.2.1 CCP PIN CONFIGURATION
The user must configure the CCPx pin as an output by
clearing the associated TRIS bit.
Also, the CCPx pin function can be moved to
alternative pins using the APFCON register. Refer to
Section 12.1 “Alternate Pin Function for more
details.
23.2.2 TIMER1 MODE RESOURCE
In Compare mode, Timer1 must be running in either
Timer mode or Synchronized Counter mode. The
compare operation may not work in Asynchronous
Counter mode.
See Section 21.0 “Timer1 Module w ith Gate Control”
for more information on configuring Timer1.
23.2.3 SOFTWARE INTERRUPT MODE
When Generate Software Interrupt mode is chosen
(CCPxM<3:0> = 1010), the CCPx module does not
assert control of the CCPx pin (see the CCPxCON
register).
23.2.4 SPECIAL EVENT TRIGGER
When Special Event Trigger mode is chosen
(CCPxM<3:0> = 1011), the CCPx module does the
following:
Resets Timer1
Starts an ADC conversion if ADC is enabled
The CCPx module does not assert control of the CCPx
pin in this mode.
The Special Event Trigger output of the CCP occurs
immediately upon a match between the TMR1H,
TMR1L register pair and the CCPRxH, CCPRxL regis-
ter pair. The TMR1H, TMR1L register pair is not reset
until the next rising edge of the Timer1 clock. The
Special Event Trigger output starts an A/D conversion
(if the A/D module is enabled). This allows the
CCPRxH, CCPRxL register pair to effectively provide a
16-bit programmable period register for Timer1.
Refer to Section 15.2.5 “Special Event Trigger”for
more information.
Note: Clearing the CCPxCON register will force
the CCPx compare output latch to the
default low level. This is not the PORT I/O
data latch.
CCPRxH CCPRxL
TMR1H TMR1L
Comparator
QS
R
Output
Logic
Special Event Trigger
Set CCPxIF Interrupt Flag
(PIRx)
Match
TRIS
CCPxM<3:0>
Mode Select
Output Enable
Pin
CCPx
4
Note: Clocking Timer1 from the system clock
(FOSC) should not be used in Compare
mode. In order for Compare mode to
recognize the trigger event on the CCPx
pin, TImer1 must be clocked from the
instruction clock (FOSC/4) or from an
external clock source.
TABLE 23-3: SPECIAL EVENT TRIGGER
Device CCPx/ECCPx
PIC16(L)F1934/6/7 CCP5
Note 1: The Special Event Trigger from the CCP
module does not set interrupt flag bit
TMR1IF of the PIR1 register.
2: Removing the match condition by
changing the contents of the CCPRxH
and CCPRxL register pair, between the
clock edge that generates the Special
Event Trigger and the clock edge that
generates the Timer1 Reset, will
preclude the Reset from occurring.
2008-2011 Microchip Technology Inc. DS41364E-page 215
PIC16(L)F1934/6/7
23.2.5 COMPARE DURING SLEEP
The Compare mode is dependent upon the system
clock (FOSC) for proper operation. Since FOSC is shut
down during Sleep mode, the Compare mode will not
function properly during Sleep.
23.2.6 ALTERNATE PIN LOCATIONS
This module incorporates I/O pins that can be moved to
other locations with the use of the alternate pin function
register, APFCON. To determine which pins can be
moved and what their default locations are upon a
Reset, see Section 12.1 “ Alternate Pin Function” for
more information.
TABLE 23-4: SUMMARY OF REGISTERS ASSOCIATED WITH COMPARE
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
APFCON CCP3SEL T1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL 131
CCPxCON PxM<1:0>(1) DCxB<1:0> CCPxM<3:0> 234
CCPRxL Capture/Compare/PWM Register x Low Byte (LSB) 212
CCPRxH Capture/Compare/PWM Register x High Byte (MSB) 212
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE TMR4IE 101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF —CCP2IF
103
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF TMR4IF 104
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON
203
T1GCON TMR1GE T1GPOL T1GTM T1GSPM T1GGO/DONE T1GVAL T1GSS<1:0> 204
TMR1L Holding Register for the Least Significant Byte of the 16-bit TMR1 Register 199
TMR1H Holding Register for the Most Significant Byte of the 16-bit TMR1 Register 199
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TRISD(2) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 145
TRISE ———— (3) TRISE2(2) TRISE1(2) TRISE0(2) 148
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by Compare mode.
Note 1: Applies to ECCP modules only.
2: These bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
3: Unimplemented, read as 1’.
PIC16(L)F1934/6/7
DS41364E-page 216 2008-2011 Microchip Technology Inc.
23.3 PWM Overview
Pulse-Width Modulation (PWM) is a scheme that
provides power to a load by switching quickly between
fully on and fully off states. The PWM signal resembles
a square wave where the high portion of the signal is
considered the on state and the low portion of the signal
is considered the off state. The high portion, also known
as the pulse width, can vary in time and is defined in
steps. A larger number of steps applied, which
lengthens the pulse width, also supplies more power to
the load. Lowering the number of steps applied, which
shortens the pulse width, supplies less power. The
PWM period is defined as the duration of one complete
cycle or the total amount of on and off time combined.
PWM resolution defines the maximum number of steps
that can be present in a single PWM period. A higher
resolution allows for more precise control of the pulse
width time and in turn the power that is applied to the
load.
The term duty cycle describes the proportion of the on
time to the off time and is expressed in percentages,
where 0% is fully off and 100% is fully on. A lower duty
cycle corresponds to less power applied and a higher
duty cycle corresponds to more power applied.
Figure 23-3 shows a typical waveform of the PWM
signal.
23.3.1 STANDARD PWM OPERATION
The standard PWM function described in this section is
available and identical for CCP modules ECCP1,
ECCP2, ECCP3, CCP4 and CCP5.
The standard PWM mode generates a Pulse-Width
modulation (PWM) signal on the CCPx pin with up to 10
bits of resolution. The period, duty cycle, and resolution
are controlled by the following registers:
•PRx registers
•TxCON registers
CCPRxL registers
CCPxCON registers
Figure 23-4 shows a simplified block diagram of PWM
operation.
FIGURE 23-3: CCP PWM OUTPUT SIGNAL
FIGURE 23-4: SIMPLIFIED PWM BLOCK
DIAGRAM
Note 1: The corresponding TRIS bit must be
cleared to enable the PWM output on the
CCPx pin.
2: Clearing the CCPxCON register will
relinquish control of the CCPx pin.
Period
Pulse Width
TMRx = 0
TMRx = CCPRxH:CCPxCON<5:4>
TMRx = PRx
CCPRxL
CCPRxH(2) (Slave)
Comparator
TMRx
PRx
(1)
RQ
S
Duty Cycle Registers CCPxCON<5:4>
Clear Timer,
toggle CCPx pin and
latch duty cycle
Note 1: The 8-bit timer TMRx register is concatenated
with the 2-bit internal system clock (FOSC), or
2 bits of the prescaler, to create the 10-bit time
base.
2: In PWM mode, CCPRxH is a read-only register.
TRIS
CCPx
Comparator
2008-2011 Microchip Technology Inc. DS41364E-page 217
PIC16(L)F1934/6/7
23.3.2 SETUP FOR PWM OPERATION
The following steps should be taken when configuring
the CCP module for standard PWM operation:
1. Disable the CCPx pin output driver by setting the
associated TRIS bit.
2. Load the PRx register with the PWM period
value.
3. Configure the CCP module for the PWM mode
by loading the CCPxCON register with the
appropriate values.
4. Load the CCPRxL register and the DCxBx bits
of the CCPxCON register, with the PWM duty
cycle value.
5. Configure and start Timer2/4/6:
Select the Timer2/4/6 resource to be used
for PWM generation by setting the
CxTSEL<1:0> bits in the CCPTMRSx
register.
Clear the TMRxIF interrupt flag bit of the
PIRx register. See Note below.
Configure the TxCKPS bits of the TxCON
register with the Timer prescale value.
Enable the Timer by setting the TMRxON
bit of the TxCON register.
6. Enable PWM output pin:
Wait until the Timer overflows and the
TMRxIF bit of the PIRx register is set. See
Note below.
Enable the CCPx pin output driver by clear-
ing the associated TRIS bit.
23.3.3 TIMER2/4/6 TIMER RESOURCE
The PWM standard mode makes use of one of the 8-bit
Timer2/4/6 timer resources to specify the PWM period.
Configuring the CxTSEL<1:0> bits in the CCPTMRSx
register selects which Timer2/4/6 timer is used.
23.3.4 PWM PERIOD
The PWM period is specified by the PRx register of
Timer2/4/6. The PWM period can be calculated using
the formula of Equation 23-1.
EQUATION 23-1: PWM PERIOD
When TMRx is equal to PRx, the following three events
occur on the next increment cycle:
TMRx is cleared
The CCPx pin is set. (Exception: If the PWM duty
cycle = 0%, the pin will not be set.)
The PWM duty cycle is latched from CCPRxL into
CCPRxH.
23.3.5 PWM DUTY CYCLE
The PWM duty cycle is specified by writing a 10-bit
value to multiple registers: CCPRxL register and
DCxB<1:0> bits of the CCPxCON register. The
CCPRxL contains the eight MSbs and the DCxB<1:0>
bits of the CCPxCON register contain the two LSbs.
CCPRxL and DCxB<1:0> bits of the CCPxCON
register can be written to at any time. The duty cycle
value is not latched into CCPRxH until after the period
completes (i.e., a match between PRx and TMRx
registers occurs). While using the PWM, the CCPRxH
register is read-only.
Equation 23-2 is used to calculate the PWM pulse
width.
Equation 23-3 is used to calculate the PWM duty cycle
ratio.
EQUATION 23-2: PULSE WIDTH
EQUATION 23-3: DUTY CYCLE RATIO
The CCPRxH register and a 2-bit internal latch are
used to double buffer the PWM duty cycle. This double
buffering is essential for glitchless PWM operation.
The 8-bit timer TMRx register is concatenated with either
the 2-bit internal system clock (FOSC), or 2 bits of the
prescaler, to create the 10-bit time base. The system
clock is used if the Timer2/4/6 prescaler is set to 1:1.
When the 10-bit time base matches the CCPRxH and
2-bit latch, then the CCPx pin is cleared (see
Figure 23-4).
Note: In order to send a complete duty cycle and
period on the first PWM output, the above
steps must be included in the setup
sequence. If it is not critical to start with a
complete PWM signal on the first output,
then step 6 may be ignored.
PWM Period PRx1+4TOSC =
(TMRx Pres c ale Val ue )
Note 1: TOSC = 1/FOSC
Note: The Timer postscaler (see Section 22.1
“Timer2/4/6 Operation”) is not used in the
determination of the PWM frequency.
Pulse Width CCPRxL:CCPxCON<5:4>
=
TOSC
(TMRx Prescale Va lue)
Duty Cycle Ratio CCPRxL:CCPxCON<5:4>
4 PRx 1+
-----------------------------------------------------------------------=
PIC16(L)F1934/6/7
DS41364E-page 218 2008-2011 Microchip Technology Inc.
23.3.6 PWM RESOLUTION
The resolution determines the number of available duty
cycles for a given period. For example, a 10-bit resolution
will result in 1024 discrete duty cycles, whereas an 8-bit
resolution will result in 256 discrete duty cycles.
The maximum PWM resolution is 10 bits when PRx is
255. The resolution is a function of the PRx register
value as shown by Equation 23-4.
EQUATION 23-4: PWM RESOLUTION
TABLE 23-5: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 32 MHz)
TABLE 23-6: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 20 MHz)
TABLE 23-7: EXAMPLE PWM FREQUENCIES AND RESOLUTIONS (FOSC = 8 MHz)
Note: If the pulse width value is greater than the
period the assigned PWM pin(s) will
remain unchanged.
Resolution 4PRx 1+log 2log
------------------------------------------ bits=
PWM Frequency 1.95 kHz 7.81 kHz 31.25 kHz 125 kHz 250 kHz 333.3 kHz
Timer Prescale (1, 4, 16) 16 4 1 1 1 1
PRx Value 0xFF 0xFF 0xFF 0x3F 0x1F 0x17
Maximum Resolution (bits) 10 10 10 8 7 6.6
PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz
Timer Prescale (1, 4, 16) 16 4 1 1 1 1
PRx Value 0xFF 0xFF 0xFF 0x3F 0x1F 0x17
Maximum Resolution (bits) 10 10 10 8 7 6.6
PWM Frequency 1.22 kHz 4.90 kHz 19.61 kHz 76.92 kHz 153.85 kHz 200.0 kHz
Timer Prescale (1, 4, 16) 16 4 1 1 1 1
PRx Value 0x65 0x65 0x65 0x19 0x0C 0x09
Maximum Resolution (bits) 8 8 8 6 5 5
2008-2011 Microchip Technology Inc. DS41364E-page 219
PIC16(L)F1934/6/7
23.3.7 OPERATION IN SLEEP MODE
In Sleep mode, the TMRx register will not increment
and the state of the module will not change. If the CCPx
pin is driving a value, it will continue to drive that value.
When the device wakes up, TMRx will continue from its
previous state.
23.3.8 CHANGES IN SYSTEM CLOCK
FREQUENCY
The PWM frequency is derived from the system clock
frequency. Any changes in the system clock frequency
will result in changes to the PWM frequency. See
Section 5.0 “Oscillator Module (With Fail-Safe
Clock Monitor)” for additional details.
23.3.9 EFFECTS OF RESET
Any Reset will force all ports to Input mode and the
CCP registers to their Reset states.
23.3.10 ALTERNATE PIN LOCATIONS
This module incorporates I/O pins that can be moved to
other locations with the use of the alternate pin function
register, APFCON. To determine which pins can be
moved and what their default locations are upon a
Reset, see Section 12.1 “ Alternate Pin Function” for
more information.
TABLE 23-8: SUMMARY OF REGISTERS ASSOCIATED WITH STANDARD PWM
Name Bit 7 Bit 6 Bit 5 B it 4 B it 3 Bit 2 B it 1 Bit 0 Register
on Page
APFCON CCP3SEL T1GSEL P2BSEL SRNQSEL
C2OUTSEL
SSSEL CCP2SEL 131
CCPxCON PxM<1:0>(1) DCxB<1:0> CCPxM<3:0> 234
CCPTMRS0 C4TSEL<1:0> C3TSEL<1:0> C2TSEL<1:0> C1TSEL<1:0> 235
CCPTMRS1 ————— C5TSEL<1:0> 235
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE TMR4IE 101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF —CCP2IF
103
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF TMR4IF 104
PRx Timer2/4/6 Period Register 207*
TxCON TxOUTPS<3:0> TMRxON TxCKPS<:0>1 209
TMRx Timer2/4/6 Module Register 207
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TRISD(2) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 145
TRISE ————(3) TRISE2(2) TRISE1(2) TRISE0(2) 148
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the PWM.
Note 1: Applies to ECCP modules only.
2: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
3: Unimplemented, read as1’.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 220 2008-2011 Microchip Technology Inc.
23.4 PWM (Enhanced Mode)
The enhanced PWM function described in this section is
available for CCP modules ECCP1, ECCP2 and
ECCP3, with any differences between modules noted.
The enhanced PWM mode generates a Pulse-Width
Modulation (PWM) signal on up to four different output
pins with up to 10 bits of resolution. The period, duty
cycle, and resolution are controlled by the following
registers:
•PRx registers
•TxCON registers
CCPRxL registers
CCPxCON registers
The ECCP modules have the following additional PWM
registers which control Auto-shutdown, Auto-restart,
Dead-band Delay and PWM Steering modes:
CCPxAS registers
PSTRxCON registers
PWMxCON registers
The enhanced PWM module can generate the following
five PWM Output modes:
Single PWM
Half-Bridge PWM
Full-Bridge PWM, Forward Mode
Full-Bridge PWM, Reverse Mode
Single PWM with PWM Steering Mode
To select an Enhanced PWM Output mode, the PxM bits
of the CCPxCON register must be configured
appropriately.
The PWM outputs are multiplexed with I/O pins and are
designated PxA, PxB, PxC and PxD. The polarity of the
PWM pins is configurable and is selected by setting the
CCPxM bits in the CCPxCON register appropriately.
Figure 23-5 shows an example of a simplified block
diagram of the Enhanced PWM module.
Table 23-9 shows the pin assignments for various
Enhanced PWM modes.
FIGURE 23-5: EXAMPLE SIMPLIFIED BLOCK DIAGRAM OF THE ENHANCED PWM MODE
Note 1: The corresponding TRIS bit must be
cleared to enable the PWM output on the
CCPx pin.
2: Clearing the CCPxCON register will
relinquish control of the CCPx pin.
3: Any pin not used in the enhanced PWM
mode is available for alternate pin
functions, if applicable.
4: To prevent the generation of an
incomplete waveform when the PWM is
first enabled, the ECCP module waits
until the start of a new PWM period
before generating a PWM signal.
CCPRxL
CCPRxH (Slave)
Comparator
TMRx
Comparator
PRx
(1)
RQ
S
Duty Cycle Registers DCxB<1:0>
Clear Timer,
toggle PWM pin and
latch duty cycle
Note 1: The 8-bit timer TMRx register is concatenated with the 2-bit internal Q clock, or 2 bits of the prescaler to create the 10-bit time
base.
TRISx
CCPx/PxA
TRISx
PxB
TRISx
PxC
TRISx
PxD
Output
Controller
PxM<1:0>
2
CCPxM<3:0>
4
PWMxCON
CCPx/PxA
PxB
PxC
PxD
2008-2011 Microchip Technology Inc. DS41364E-page 221
PIC16(L)F1934/6/7
TABLE 23-9: EXAMPLE PIN ASSIGNMENTS FOR VARIOUS PWM ENHANCED MODES
FIGURE 23-6: EXAMPLE PW M (ENHANCED MODE) OUTPUT RELATIONSHIPS (ACTIVE-HIGH
STATE)
ECCP Mode PxM<1:0> CCPx/PxA PxB PxC PxD
Single 00 Yes(1) Yes(1) Yes(1) Yes (1)
Half-Bridge 10 Yes Yes No No
Full-Bridge, Forward 01 Yes Yes Yes Yes
Full-Bridge, Reverse 11 Yes Yes Yes Yes
Note 1: PWM Steering enables outputs in Single mode.
0
Period
00
10
01
11
Signal PRX+1
PxM<1:0>
PxA Modulated
PxA Modulated
PxB Modulated
PxA Active
PxB Inactive
PxC Inactive
PxD Modulated
PxA Inactive
PxB Modulated
PxC Active
PxD Inactive
Pulse
Width
(Single Output)
(Half-Bridge)
(Full-Bridge,
Forward)
(Full-Bridge,
Reverse)
Delay Delay
Relationships:
Period = 4 * TOSC * (PRx + 1) * (TMRx Prescale Value)
Pulse Width = TOSC * (CCPRxL<7:0>:CCPxCON<5:4>) * (TMRx Prescale Value)
Delay = 4 * TOSC * (PWMxCON<6:0>)
PIC16(L)F1934/6/7
DS41364E-page 222 2008-2011 Microchip Technology Inc.
FIGURE 23-7: EXAMPLE ENHANCED PWM OUTPUT RELATIONSHIPS (ACTIVE-LOW STATE)
0
Period
00
10
01
11
Signal PRx+1
PxM<1:0>
PxA Modulated
PxA Modulated
PxB Modulated
PxA Active
PxB Inactive
PxC Inactive
PxD Modulated
PxA Inactive
PxB Modulated
PxC Active
PxD Inactive
Pulse
Width
(Single Output)
(Half-Bridge)
(Full-Bridge,
Forward)
(Full-Bridge,
Reverse)
Delay Delay
Relationships:
Period = 4 * TOSC * (PRx + 1) * (TMRx Prescale Value)
Pulse Width = TOSC * (CCPRxL<7:0>:CCPxCON<5:4>) * (TMRx Prescale Value)
Delay = 4 * TOSC * (PWMxCON<6:0>)
2008-2011 Microchip Technology Inc. DS41364E-page 223
PIC16(L)F1934/6/7
23.4.1 HALF-BRIDGE MODE
In Half-Bridge mode, two pins are used as outputs to
drive push-pull loads. The PWM output signal is output
on the CCPx/PxA pin, while the complementary PWM
output signal is output on the PxB pin (see
Figure 23-9). This mode can be used for Half-Bridge
applications, as shown in Figure 23-9, or for Full-Bridge
applications, where four power switches are being
modulated with two PWM signals.
In Half-Bridge mode, the programmable dead-band delay
can be used to prevent shoot-through current in
Half-Bridge power devices. The value of the PDC<6:0>
bits of the PWMxCON register sets the number of
instruction cycles before the output is driven active. If the
value is greater than the duty cycle, the corresponding
output remains inactive during the entire cycle. See
Section 23.4.5 “Programmable Dead-Band Delay
Mode” for more details of the dead-band delay
operations.
Since the PxA and PxB outputs are multiplexed with the
PORT data latches, the associated TRIS bits must be
cleared to configure PxA and PxB as outputs.
FIGURE 23-8: EXAMPLE OF
HALF-BRIDGE PWM
OUTPUT
FIGURE 23-9: EXAMPL E OF HALF-BRIDGE APPLICATIONS
Period
Pulse Width
td
td
(1)
PxA(2)
PxB(2)
td = Dead-Band Delay
Period
(1) (1)
Note 1: At this time, the TMRx register is equal to the
PRx register.
2: Output signals are shown as active-high.
PxA
PxB
FET
Driver
FET
Driver
Load
+
-
+
-
FET
Driver
FET
Driver
V+
Load
FET
Driver
FET
Driver
PxA
PxB
Standard Half-Bridge Circuit (“Push-P ull ”)
Half-Bridge Output Driving a Full-Bridge Circuit
PIC16(L)F1934/6/7
DS41364E-page 224 2008-2011 Microchip Technology Inc.
23.4.2 FULL-BRIDGE MODE
In Full-Bridge mode, all four pins are used as outputs.
An example of Full-Bridge application is shown in
Figure 23-10.
In the Forward mode, pin CCPx/PxA is driven to its active
state, pin PxD is modulated, while PxB and PxC will be
driven to their inactive state as shown in Figure 23-11.
In the Reverse mode, PxC is driven to its active state, pin
PxB is modulated, while PxA and PxD will be driven to
their inactive state as shown Figure 23-11.
PxA, PxB, PxC and PxD outputs are multiplexed with
the PORT data latches. The associated TRIS bits must
be cleared to configure the PxA, PxB, PxC and PxD
pins as outputs.
FIGURE 23-10: EXAMPLE OF FULL-BRIDGE APPLICATION
PxA
PxC
FET
Driver
FET
Driver
V+
V-
Load
FET
Driver
FET
Driver
PxB
PxD
QA
QB QD
QC
2008-2011 Microchip Technology Inc. DS41364E-page 225
PIC16(L)F1934/6/7
FIGURE 23-11: EXAMPLE OF FULL-BRIDGE PWM OUTPUT
Period
Pulse Width
PxA(2)
PxB(2)
PxC(2)
PxD(2)
Forw a r d M o de
(1)
Period
Pulse Width
PxA(2)
PxC(2)
PxD(2)
PxB(2)
Reverse Mode
(1)
(1)
(1)
Note 1: At this time, the TMRx register is equal to the PRx register.
2: Output signal is shown as active-high.
PIC16(L)F1934/6/7
DS41364E-page 226 2008-2011 Microchip Technology Inc.
23.4.2.1 Direction Change in Full-Bridge
Mode
In the Full-Bridge mode, the PxM1 bit in the CCPxCON
register allows users to control the forward/reverse
direction. When the application firmware changes this
direction control bit, the module will change to the new
direction on the next PWM cycle.
A direction change is initiated in software by changing
the PxM1 bit of the CCPxCON register. The following
sequence occurs four Timer cycles prior to the end of
the current PWM period:
The modulated outputs (PxB and PxD) are placed
in their inactive state.
The associated unmodulated outputs (PxA and
PxC) are switched to drive in the opposite
direction.
PWM modulation resumes at the beginning of the
next period.
See Figure 23-12 for an illustration of this sequence.
The Full-Bridge mode does not provide dead-band
delay. As one output is modulated at a time, dead-band
delay is generally not required. There is a situation
where dead-band delay is required. This situation
occurs when both of the following conditions are true:
1. The direction of the PWM output changes when
the duty cycle of the output is at or near 100%.
2. The turn off time of the power switch, including
the power device and driver circuit, is greater
than the turn on time.
Figure 23-13 shows an example of the PWM direction
changing from forward to reverse, at a near 100% duty
cycle. In this example, at time t1, the output PxA and
PxD become inactive, while output PxC becomes
active. Since the turn off time of the power devices is
longer than the turn on time, a shoot-through current
will flow through power devices QC and QD (see
Figure 23-10) for the duration of ‘t’. The same
phenomenon will occur to power devices QA and QB
for PWM direction change from reverse to forward.
If changing PWM direction at high duty cycle is required
for an application, two possible solutions for eliminating
the shoot-through current are:
1. Reduce PWM duty cycle for one PWM period
before changing directions.
2. Use switch drivers that can drive the switches off
faster than they can drive them on.
Other options to prevent shoot-through current may
exist.
FIGURE 23-12: EXAMPLE OF PWM DIRECTION CHANGE
Pulse Width
Period(1)
Signal
Note 1: The direction bit PxM1 of the CCPxCON register is written any time during the PWM cycle.
2: When changing directions, the PxA and PxC signals switch before the end of the current PWM cycle. The
modulated PxB and PxD signals are inactive at this time. The length of this time is four Timer counts.
Period
(2)
PxA (Active-High)
PxB (Active-High)
PxC (Active-High)
PxD (Active-High)
Pulse Width
2008-2011 Microchip Technology Inc. DS41364E-page 227
PIC16(L)F1934/6/7
FIGURE 23-13: EXAMPLE OF PWM DIR ECTION CHANGE AT NEAR 100% DUTY CYCLE
Forward Period Reverse Period
PxA
TON
TOFF
T = TOFF – TON
PxB
PxC
PxD
External Switch D
Potential
Shoot-Through Current
Note 1: All signals are shown as active-high.
2: TON is the turn on delay of power switch QC and its driver.
3: TOFF is the turn off delay of power switch QD and its driver.
External Switch C
t1
PW
PW
PIC16(L)F1934/6/7
DS41364E-page 228 2008-2011 Microchip Technology Inc.
23.4.3 ENHANCED PWM
AUTO-SHUTDOWN MODE
The PWM mode supports an Auto-Shutdown mode that
will disable the PWM outputs when an external
shutdown event occurs. Auto-Shutdown mode places
the PWM output pins into a predetermined state. This
mode is used to help prevent the PWM from damaging
the application.
The auto-shutdown sources are selected using the
CCPxAS<2:0> bits of the CCPxAS register. A shutdown
event may be generated by:
•A logic0’ on the INT pin
•A logic1’ on a Comparator (Cx) output
A shutdown condition is indicated by the CCPxASE
(Auto-Shutdown Event Status) bit of the CCPxAS
register. If the bit is a ‘0’, the PWM pins are operating
normally. If the bit is a ‘1’, the PWM outputs are in the
shutdown state.
When a shutdown event occurs, two things happen:
The CCPxASE bit is set to ‘1’. The CCPxASE will
remain set until cleared in firmware or an auto-restart
occurs (see Section 23.4.4 “Auto-Restart Mode” ).
The enabled PWM pins are asynchronously placed in
their shutdown states. The PWM output pins are
grouped into pairs [PxA/PxC] and [PxB/PxD]. The state
of each pin pair is determined by the PSSxAC and
PSSxBD bits of the CCPxAS register. Each pin pair may
be placed into one of three states:
•Drive logic 1
•Drive logic 0
Tri-state (high-impedance)
FIGURE 23-14: PWM AUTO-SHUTDOWN WITH FIRMWARE RESTART (PXRSEN = 0)
Note 1: The auto-shutdown condition is a
level-based signal, not an edge-based
signal. As long as the level is present, the
auto-shutdown will persist.
2: Writing to the CCPxASE bit is disabled
while an auto-shutdown condition
persists.
3: Once the auto-shutdown condition has
been removed and the PWM restarted
(either through firmware or auto-restart)
the PWM signal will always restart at the
beginning of the next PWM period.
4: Prior to an auto-shutdown event caused
by a comparator output or INT pin event,
a software shutdown can be triggered in
firmware by setting the CCPxASE bit of
the CCPxAS register to ‘1’. The
Auto-Restart feature tracks the active sta-
tus of a shutdown caused by a compara-
tor output or INT pin event only. If it is
enabled at this time, it will immediately
clear this bit and restart the ECCP mod-
ule at the beginning of the next PWM
period.
Shutdown
PWM
CCPxASE bit
Activity
Event
Shutdown
Event Occurs Shutdown
Event Clears
PWM
Resumes
PWM Period
Start of
PWM Period
CCPxASE
Cleared by
Firmware
Timer
Overflow Timer
Overflow
Timer
Overflow Timer
Overflow
Missing Pulse
(Auto-Shutdown) Missing Pulse
(CCPxASE not clear)
Timer
Overflow
2008-2011 Microchip Technology Inc. DS41364E-page 229
PIC16(L)F1934/6/7
23.4.4 AUTO-RESTART MODE
The Enhanced PWM can be configured to automati-
cally restart the PWM signal once the auto-shutdown
condition has been removed. Auto-restart is enabled by
setting the PxRSEN bit in the PWMxCON register.
If auto-restart is enabled, the CCPxASE bit will remain
set as long as the auto-shutdown condition is active.
When the auto-shutdown condition is removed, the
CCPxASE bit will be cleared via hardware and normal
operation will resume.
FIGURE 23-15: PWM AUTO-SHUTDOWN WITH AUTO-RESTART (PXRSEN = 1)
Shutdown
PWM
CCPxASE bit
Activity
Event
Shutdown
Event Occurs
Shutdown
Event Clears
PWM Period
Start of
PWM Period
CCPxASE
Cleared by
Hardware
Timer
Overflow Timer
Overflow
Timer
Overflow Timer
Overflow
Missing Pulse
(Auto-Shutdown) Missing Pulse
(CCPxASE not clear)
Timer
Overflow
PWM
Resumes
PIC16(L)F1934/6/7
DS41364E-page 230 2008-2011 Microchip Technology Inc.
23.4.5 PROGRAMMABLE DEAD-BAND
DELAY MODE
In Half-Bridge applications where all power switches
are modulated at the PWM frequency, the power
switches normally require more time to turn off than to
turn on. If both the upper and lower power switches are
switched at the same time (one turned on, and the
other turned off), both switches may be on for a short
period of time until one switch completely turns off.
During this brief interval, a very high current
(shoot-through current) will flow through both power
switches, shorting the bridge supply. To avoid this
potentially destructive shoot-through current from
flowing during switching, turning on either of the power
switches is normally delayed to allow the other switch
to completely turn off.
In Half-Bridge mode, a digitally programmable
dead-band delay is available to avoid shoot-through
current from destroying the bridge power switches. The
delay occurs at the signal transition from the non-active
state to the active state. See Figure 23-16 for
illustration. The lower seven bits of the associated
PWMxCON register (Register 23-5) sets the delay
period in terms of microcontroller instruction cycles
(TCY or 4 TOSC).
FIGURE 23-16: EXAMPLE OF
HALF-BRIDGE PWM
OUTPUT
FIGURE 23-17 : EXAMPLE OF HALF-BRIDGE APPLICATIONS
Period
Pulse Width
td
td
(1)
PxA(2)
PxB(2)
td = Dead-Band Delay
Period
(1) (1)
Note 1: At this time, the TMRx register is equal to the
PRx register.
2: Output signals are shown as active-high.
PxA
PxB
FET
Driver
FET
Driver
V+
V-
Load
+
V
-
+
V
-
Standard Half-Bridge Circuit (“Push-P ull ”)
2008-2011 Microchip Technology Inc. DS41364E-page 231
PIC16(L)F1934/6/7
23.4.6 PWM STEERING MODE
In Single Output mode, PWM steering allows any of the
PWM pins to be the modulated signal. Additionally, the
same PWM signal can be simultaneously available on
multiple pins.
Once the Single Output mode is selected
(CCPxM<3:2> = 11 and PxM<1:0> = 00 of the
CCPxCON register), the user firmware can bring out
the same PWM signal to one, two, three or four output
pins by setting the appropriate STRx<D:A> bits of the
PSTRxCON register, as shown in Ta bl e 23 - 9 .
While the PWM Steering mode is active, CCPxM<1:0>
bits of the CCPxCON register select the PWM output
polarity for the Px<D:A> pins.
The PWM auto-shutdown operation also applies to
PWM Steering mode as described in Section 23.4.3
“Enhanced PWM Auto-shutdown mode”. An
auto-shutdown event will only affect pins that have
PWM outputs enabled.
FIGURE 23-18: SIMPLIFIED STEERING
BLOCK DIAGRAM
Note: The associated TRIS bits must be set to
output (0’) to enable the pin output driver
in order to see the PWM signal on the pin.
1
0TRIS
PxA pin
PORT Data
PxA Signal
STRxA
1
0TRIS
PxB pin
PORT Data
STRxB
1
0
TRIS
PxC pin
PORT Data
STRxC
1
0
TRIS
PxD pin
PORT Data
STRxD
Note 1: Port outputs are configured as shown when
the CCPxCON register bits PxM<1:0> = 00
and CCPxM<3:2> = 11.
2: Single PWM output requires setting at least
one of the STRx bits.
CCPxM1
CCPxM0
CCPxM1
CCPxM0
PIC16(L)F1934/6/7
DS41364E-page 232 2008-2011 Microchip Technology Inc.
23.4.6.1 Steering Synchronization
The STRxSYNC bit of the PSTRxCON register gives
the user two selections of when the steering event will
happen. When the STRxSYNC bit is ‘0’, the steering
event will happen at the end of the instruction that
writes to the PSTRxCON register. In this case, the
output signal at the Px<D:A> pins may be an
incomplete PWM waveform. This operation is useful
when the user firmware needs to immediately remove
a PWM signal from the pin.
When the STRxSYNC bit is ‘1’, the effective steering
update will happen at the beginning of the next PWM
period. In this case, steering on/off the PWM output will
always produce a complete PWM waveform.
Figures 23-19 and 23-20 illustrate the timing diagrams
of the PWM steering depending on the STRxSYNC
setting.
23.4.7 START-UP CONSIDERATIONS
When any PWM mode is used, the application
hardware must use the proper external pull-up and/or
pull-down resistors on the PWM output pins.
The CCPxM<1:0> bits of the CCPxCON register allow
the user to choose whether the PWM output signals are
active-high or active-low for each pair of PWM output
pins (PxA/PxC and PxB/PxD). The PWM output
polarities must be selected before the PWM pin output
drivers are enabled. Changing the polarity
configuration while the PWM pin output drivers are
enable is not recommended since it may result in
damage to the application circuits.
The PxA, PxB, PxC and PxD output latches may not be
in the proper states when the PWM module is
initialized. Enabling the PWM pin output drivers at the
same time as the Enhanced PWM modes may cause
damage to the application circuit. The Enhanced PWM
modes must be enabled in the proper Output mode and
complete a full PWM cycle before enabling the PWM
pin output drivers. The completion of a full PWM cycle
is indicated by the TMRxIF bit of the PIRx register
being set as the second PWM period begins.
FIGURE 23-19: EXAMPLE OF STEERING EVENT AT END OF INSTRUCTION (STRxSYNC = 0)
FIGURE 23-20: EXAMPLE OF STEERING EVENT AT BEGINNING OF INSTRUCTION
(STRxSYNC = 1)
Note: When the microcontroller is released from
Reset, all of the I/O pins are in the
high-impedance state. The external cir-
cuits must keep the power switch devices
in the Off state until the microcontroller
drives the I/O pins with the proper signal
levels or activates the PWM output(s).
PWM
P1n = PWM
STRx
P1<D:A> PORT Data
PWM Period
PORT Data
PWM
PORT Data
P1n = PWM
STRx
P1<D:A> PORT Data
2008-2011 Microchip Technology Inc. DS41364E-page 233
PIC16(L)F1934/6/7
TABLE 23-10: SUMMARY OF REGISTERS ASSOCIATED WITH ENHANCED PWM
Name Bit 7 Bit 6 Bit 5 B it 4 B it 3 Bit 2 B it 1 Bit 0 Register
on Page
CCPxCON PxM<1:0>(1) DCxB<1:0> CCPxM<3:0> 234
CCPxAS CCPxASE CCPxAS<2:0> PSSxAC<1:0> PSSxBD<1:0> 236
CCPTMRS0 C4TSEL<1:0> C3TSEL<1:0> C2TSEL<1:0> C1TSEL<1:0> 235
CCPTMRS1 ————— C5TSEL<1:0> 235
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIE3 CCP5IE CCP4IE CCP3IE TMR6IE TMR4IE 101
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF —CCP2IF
103
PIR3 CCP5IF CCP4IF CCP3IF TMR6IF TMR4IF 104
PRx Timer2/4/6 Period Register 207*
PSTRxCON —— STRxSYNC STRxD STRxC STRxB STRxA 238
PWMxCON PxRSEN PxDC<6:0> 237
TxCON TxOUTPS<3:0> TMRxON TxCKPS<:0>1 209
TMRx Timer2/4/6 Module Register 207
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TRISD(2) TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 145
TRISE ————(3) TRISE2(2) TRISE1(2) TRISE0(2) 148
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the PWM.
Note 1: Applies to ECCP modules only.
2: These registers/bits are not implemented on PIC16(L)F1936 devices, read as ‘0’.
3: Unimplemented, read as 1’.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 234 2008-2011 Microchip Technology Inc.
23.5 CCP Control Register
REGISTER 23-1: CCPxCON: CCPx CONTROL REGISTER
R/W-00 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
PxM<1:0>(1) DCxB<1:0> CCPxM<3:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Reset
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-6 PxM<1:0>: Enhanced PWM Output Configuration bits(1)
Capture mode:
Unused
Compare mode:
Unused
If CCPxM<3:2> = 00, 01, 10:
xx = PxA assigned as Capture/Compare input; PxB, PxC, PxD assigned as port pins
If CCPxM<3:2> = 11:
00 = Single output; PxA modulated; PxB, PxC, PxD assigned as port pins
01 = Full-Bridge output forward; PxD modulated; PxA active; PxB, PxC inactive
10 = Half-Bridge output; PxA, PxB modulated with dead-band control; PxC, PxD assigned as port pins
11 = Full-Bridge output reverse; PxB modulated; PxC active; PxA, PxD inactive
bit 5-4 DCxB<1:0>: PWM Duty Cycle Least Significant bits
Capture mode:
Unused
Compare mode:
Unused
PWM mode:
These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPRxL.
bit 3-0 CCPxM<3:0>: ECCPx Mode Select bits
0000 = Capture/Compare/PWM off (resets ECCPx module)
0001 = Reserved
0010 = Compare mode: toggle output on match
0011 = Reserved
0100 = Capture mode: every falling edge
0101 = Capture mode: every rising edge
0110 = Capture mode: every 4th rising edge
0111 = Capture mode: every 16th rising edge
1000 = Compare mode: initialize ECCPx pin low; set output on compare match (set CCPxIF)
1001 = Compare mode: initialize ECCPx pin high; clear output on compare match (set CCPxIF)
1010 = Compare mode: generate software interrupt only; ECCPx pin reverts to I/O state
1011 = Compare mode: Special Event Trigger (ECCPx resets Timer, sets CCPxIF bit starts A/D conversion if A/D
module is enabled)(1)
CCP4/CCP5 only:
11xx =PWM mode
ECCP1/ECCP2/ECCP3 only:
1100 = PWM mode: PxA, PxC active-high; PxB, PxD active-high
1101 = PWM mode: PxA, PxC active-high; PxB, PxD active-low
1110 = PWM mode: PxA, PxC active-low; PxB, PxD active-high
1111 = PWM mode: PxA, PxC active-low; PxB, PxD active-low
Note 1: These bits are not implemented on CCP4 and CCP5.
2008-2011 Microchip Technology Inc. DS41364E-page 235
PIC16(L)F1934/6/7
REGISTER 23-2: CCPTMRS0: PWM TIMER SELECTION CONTROL REGISTER 0
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
C4TSEL<1:0> C3TSEL<1:0> C2TSEL<1:0> C1TSEL<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-6 C4TSEL<1:0>: CCP4 Timer Selection bits
00 = CCP4 is based off Timer2 in PWM mode
01 = CCP4 is based off Timer4 in PWM mode
10 = CCP4 is based off Timer6 in PWM mode
11 =Reserved
bit 5-4 C3TSEL<1:0>: CCP3 Timer Selection bits
00 = CCP3 is based off Timer2 in PWM mode
01 = CCP3 is based off Timer4 in PWM mode
10 = CCP3 is based off Timer6 in PWM mode
11 =Reserved
bit 3-2 C2TSEL<1:0>: CCP2 Timer Selection bits
00 = CCP2 is based off Timer2 in PWM mode
01 = CCP2 is based off Timer4 in PWM mode
10 = CCP2 is based off Timer6 in PWM mode
11 =Reserved
bit 1-0 C1TSEL<1:0>: CCP1 Timer Selection bits
00 = CCP1 is based off Timer2 in PWM mode
01 = CCP1 is based off Timer4 in PWM mode
10 = CCP1 is based off Timer6 in PWM mode
11 =Reserved
REGISTER 23-3: CCPTMRS1: PWM TIMER SELECTION CONTROL REGISTER 1
U-0 U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0
C5TSEL<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-2 Unimplemented: Read as0
bit 1-0 C5TSEL<1:0>: CCP5 Timer Selection bits
00 = CCP5 is based off Timer2 in PWM mode
01 = CCP5 is based off Timer4 in PWM mode
10 = CCP5 is based off Timer6 in PWM mode
11 =Reserved
PIC16(L)F1934/6/7
DS41364E-page 236 2008-2011 Microchip Technology Inc.
REGISTER 23-4: CCPxAS: CCPX AUTO-SHUTDOWN CONTROL REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
CCPxASE CCPxAS<2:0> PSSxAC<1:0> PSSxBD<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 CCPxASE: CCPx Auto-Shutdown Event Status bit
1 = A shutdown event has occurred; CCPx outputs are in shutdown state
0 = CCPx outputs are operating
bit 6-4 CCPxAS<2:0>: CCPx Auto-Shutdown Source Select bits
000 = Auto-shutdown is disabled
001 = Comparator C1 output high(1)
010 = Comparator C2 output high(1)
011 = Either Comparator C1 or C2 high(1)
100 =VIL on INT pin
101 =V
IL on INT pin or Comparator C1 high(1)
110 =VIL on INT pin or Comparator C2 high(1)
111 =VIL on INT pin or Comparator C1 or Comparator C2 high(1)
bit 3-2 PSSxAC<1:0>: Pins PxA and PxC Shutdown State Control bits
00 = Drive pins PxA and PxC to ‘0
01 = Drive pins PxA and PxC to ‘1
1x = Pins PxA and PxC tri-state
bit 1-0 PSSxBD<1:0>: Pins PxB and PxD Shutdown State Control bits
00 = Drive pins PxB and PxD to ‘0
01 = Drive pins PxB and PxD to ‘1
1x = Pins PxB and PxD tri-state
Note 1: If CxSYNC is enabled, the shutdown will be delayed by Timer1.
2008-2011 Microchip Technology Inc. DS41364E-page 237
PIC16(L)F1934/6/7
REGISTER 23-5: PWMxCON: ENHANCED PWM CONTROL REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
PxRSEN PxDC<6:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7 PxRSEN: PWM Restart Enable bit
1 = Upon auto-shutdown, the CCPxASE bit clears automatically once the shutdown event goes away;
the PWM restarts automatically
0 = Upon auto-shutdown, CCPxASE must be cleared in software to restart the PWM
bit 6-0 PxDC<6:0>: PWM Delay Count bits
PxDCx = Number of FOSC/4 (4 * TOSC) cycles between the scheduled time when a PWM signal
should transition active and the actual time it transitions active
Note 1: Bit resets to ‘0’ with Two-Speed Start-up and LP, XT or HS selected as the Oscillator mode or Fail-Safe
mode is enabled.
PIC16(L)F1934/6/7
DS41364E-page 238 2008-2011 Microchip Technology Inc.
REGISTER 23-6: PSTRxCON : PWM STEERING CONTROL REGISTER(1)
U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-1/1
STRxSYNC STRxD STRxC STRxB STRxA
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
bit 7-5 Unimplemented: Read as0
bit 4 STRxSYNC: Steering Sync bit
1 = Output steering update occurs on next PWM period
0 = Output steering update occurs at the beginning of the instruction cycle boundary
bit 3 STRxD: Steering Enable bit D
1 = PxD pin has the PWM waveform with polarity control from CCPxM<1:0>
0 = PxD pin is assigned to port pin
bit 2 STRxC: Steering Enable bit C
1 = PxC pin has the PWM waveform with polarity control from CCPxM<1:0>
0 = PxC pin is assigned to port pin
bit 1 STRxB: Steering Enable bit B
1 = PxB pin has the PWM waveform with polarity control from CCPxM<1:0>
0 = PxB pin is assigned to port pin
bit 0 STRxA: Steering Enable bit A
1 = PxA pin has the PWM waveform with polarity control from CCPxM<1:0>
0 = PxA pin is assigned to port pin
Note 1: The PWM Steering mode is available only when the CCPxCON register bits CCPxM<3:2> = 11 and
PxM<1:0> = 00.
2008-2011 Microchip Technology Inc. DS41364E-page 239
PIC16(L)F1934/6/7
24.0 MASTER SYNCHRONOUS
SERIAL PORT MODULE
24.1 Master SSP (MSSP) Module
Overview
The Master Synchronous Serial Port (MSSP) module is
a serial interface useful for communicating with other
peripheral or microcontroller devices. These peripheral
devices may be serial EEPROMs, shift registers, dis-
play drivers, A/D converters, etc. The MSSP module
can operate in one of two modes:
Serial Peripheral Interface (SPI)
Inter-Integrated Circuit (I2C™)
The SPI interface supports the following modes and
features:
•Master mode
Slave mode
Clock Parity
Slave Select Synchronization (Slave mode only)
Daisy-chain connection of slave devices
Figure 24-1 is a block diagram of the SPI interface
module.
FIGURE 24-1: MSSP BLOCK DIAGRAM (SPI MODE)
( )
Read Write
Data Bus
SSPSR Reg
SSPM<3:0>
bit 0 Shift
Clock
SS Control
Enable
Edge
Select
Clock Select
TMR2 Output
TOSC
Prescaler
4, 16, 64
2
Edge
Select
2 (CKP, CKE)
4
TRIS bit
SDO
SSPBUF Reg
SDI
SS
SCK
Baud rate
generator
(SSPADD)
PIC16(L)F1934/6/7
DS41364E-page 240 2008-2011 Microchip Technology Inc.
The I2C interface supports the following modes and
features:
•Master mode
Slave mode
Byte NACKing (Slave mode)
Limited Multi-master support
7-bit and 10-bit addressing
Start and Stop interrupts
Interrupt masking
Clock stretching
Bus collision detection
General call address matching
•Address masking
Address Hold and Data Hold modes
Selectable SDA hold times
Figure 24-2 is a block diagram of the I2C interface mod-
ule in Master mode. Figure 24-3 is a diagram of the I2C
interface module in Slave mode.
FIGURE 24-2: MSSP BLOCK DIAGRAM (I2C™ MASTER MODE)
Read Write
SSPSR
Start bit, Stop bit,
Start bit detect,
SSPBUF
Internal
data bus
Set/Reset: S, P, SSPSTAT, WCOL, SSPOV
Shift
Clock
MSb LSb
SDA
Acknowledge
Generate (SSPCON2)
Stop bit detect
Write collision detect
Clock arbitration
State counter for
end of XMIT/RCV
SCL
SCL in
Bus Collision
SDA in
Receive Enable (RCEN)
Clock Cntl
Clock arbitrate/BCOL detect
(Hold off clock source)
[SSPM 3:0]
Baud Rate
Reset SEN, PEN (SSPCON2)
Generator
(SSPADD)
Address Match detect
Set SSPIF, BCLIF
2008-2011 Microchip Technology Inc. DS41364E-page 241
PIC16(L)F1934/6/7
FIGURE 24-3: MSSP BLOCK DIAGRAM (I2C™ SLAVE MODE)
Read Write
SSPSR Reg
Match Detect
SSPADD Reg
Start and
Stop bit Detect
SSPBUF Reg
Internal
Data Bus
Addr Match
Set, Reset
S, P bits
(SSPSTAT Reg)
SCL
SDA
Shift
Clock
MSb LSb
SSPMSK Reg
PIC16(L)F1934/6/7
DS41364E-page 242 2008-2011 Microchip Technology Inc.
24.2 SPI Mode Overview
The Serial Peripheral Interface (SPI) bus is a
synchronous serial data communication bus that
operates in Full-Duplex mode. Devices communicate
in a master/slave environment where the master device
initiates the communication. A slave device is
controlled through a Chip Select known as Slave
Select.
The SPI bus specifies four signal connections:
Serial Clock (SCK)
Serial Data Out (SDO)
Serial Data In (SDI)
Slave Select (SS)
Figure 24-1 shows the block diagram of the MSSP
module when operating in SPI Mode.
The SPI bus operates with a single master device and
one or more slave devices. When multiple slave
devices are used, an independent Slave Select con-
nection is required from the master device to each
slave device.
Figure 24-4 shows a typical connection between a
master device and multiple slave devices.
The master selects only one slave at a time. Most slave
devices have tri-state outputs so their output signal
appears disconnected from the bus when they are not
selected.
Transmissions involve two shift registers, eight bits in
size, one in the master and one in the slave. With either
the master or the slave device, data is always shifted
out one bit at a time, with the Most Significant bit (MSb)
shifted out first. At the same time, a new Least
Significant bit (LSb) is shifted into the same register.
Figure 24-5 shows a typical connection between two
processors configured as master and slave devices.
Data is shifted out of both shift registers on the pro-
grammed clock edge and latched on the opposite edge
of the clock.
The master device transmits information out on its SDO
output pin which is connected to, and received by, the
slave’s SDI input pin. The slave device transmits infor-
mation out on its SDO output pin, which is connected
to, and received by, the master’s SDI input pin.
To begin communication, the master device first sends
out the clock signal. Both the master and the slave
devices should be configured for the same clock polar-
ity.
The master device starts a transmission by sending out
the MSb from its shift register. The slave device reads
this bit from that same line and saves it into the LSb
position of its shift register.
During each SPI clock cycle, a full-duplex data
transmission occurs. This means that while the master
device is sending out the MSb from its shift register (on
its SDO pin) and the slave device is reading this bit and
saving it as the LSb of its shift register, that the slave
device is also sending out the MSb from its shift register
(on its SDO pin) and the master device is reading this
bit and saving it as the LSb of its shift register.
After 8 bits have been shifted out, the master and slave
have exchanged register values.
If there is more data to exchange, the shift registers are
loaded with new data and the process repeats itself.
Whether the data is meaningful or not (dummy data),
depends on the application software. This leads to
three scenarios for data transmission:
Master sends useful data and slave sends dummy
data.
Master sends useful data and slave sends useful
data.
Master sends dummy data and slave sends useful
data.
Transmissions may involve any number of clock
cycles. When there is no more data to be transmitted,
the master stops sending the clock signal and it dese-
lects the slave.
Every slave device connected to the bus that has not
been selected through its slave select line must disre-
gard the clock and transmission signals and must not
transmit out any data of its own.
2008-2011 Microchip Technology Inc. DS41364E-page 243
PIC16(L)F1934/6/7
FIGURE 24-4: SPI MASTER AND MULTIPLE SLAVE CONNECTION
24.2.1 SPI MODE REGISTERS
The MSSP module has five registers for SPI mode
operation. These are:
MSSP STATUS register (SSPSTAT)
MSSP Control Register 1 (SSPCON1)
MSSP Control Register 3 (SSPCON3)
MSSP Data Buffer register (SSPBUF)
MSSP Address register (SSPADD)
MSSP Shift register (SSPSR)
(Not directly accessible)
SSPCON1 and SSPSTAT are the control and STATUS
registers in SPI mode operation. The SSPCON1 regis-
ter is readable and writable. The lower 6 bits of the
SSPSTAT are read-only. The upper two bits of the
SSPSTAT are read/write.
In one SPI master mode, SSPADD can be loaded with
a value used in the Baud Rate Generator. More infor-
mation on the Baud Rate Generator is available in
Section 24.7 “Baud Rate Generator”.
SSPSR is the shift register used for shifting data in and
out. SSPBUF provides indirect access to the SSPSR
register. SSPBUF is the buffer register to which data
bytes are written, and from which data bytes are read.
In receive operations, SSPSR and SSPBUF together
create a buffered receiver. When SSPSR receives a
complete byte, it is transferred to SSPBUF and the
SSPIF interrupt is set.
During transmission, the SSPBUF is not buffered. A
write to SSPBUF will write to both SSPBUF and
SSPSR.
SPI Master SCK
SDO
SDI
General I/O
General I/O
General I/O
SCK
SDI
SDO
SS
SPI Slave
#1
SCK
SDI
SDO
SS
SPI Slave
#2
SCK
SDI
SDO
SS
SPI Slave
#3
PIC16(L)F1934/6/7
DS41364E-page 244 2008-2011 Microchip Technology Inc.
24.2.2 SPI MODE OPERATION
When initializing the SPI, several options need to be
specified. This is done by programming the appropriate
control bits (SSPCON1<5:0> and SSPSTAT<7:6>).
These control bits allow the following to be specified:
Master mode (SCK is the clock output)
Slave mode (SCK is the clock input)
Clock Polarity (Idle state of SCK)
Data Input Sample Phase (middle or end of data
output time)
Clock Edge (output data on rising/falling edge of
SCK)
Clock Rate (Master mode only)
Slave Select mode (Slave mode only)
To enable the serial port, SSP Enable bit, SSPEN of the
SSPCON1 register, must be set. To reset or reconfig-
ure SPI mode, clear the SSPEN bit, re-initialize the
SSPCONx registers and then set the SSPEN bit. This
configures the SDI, SDO, SCK and SS pins as serial
port pins. For the pins to behave as the serial port func-
tion, some must have their data direction bits (in the
TRIS register) appropriately programmed as follows:
SDI must have corresponding TRIS bit set
SDO must have corresponding TRIS bit cleared
SCK (Master mode) must have corresponding
TRIS bit cleared
SCK (Slave mode) must have corresponding
TRIS bit set
•SS
must have corresponding TRIS bit set
Any serial port function that is not desired may be
overridden by programming the corresponding data
direction (TRIS) register to the opposite value.
The MSSP consists of a transmit/receive shift register
(SSPSR) and a buffer register (SSPBUF). The SSPSR
shifts the data in and out of the device, MSb first. The
SSPBUF holds the data that was written to the SSPSR
until the received data is ready. Once the 8 bits of data
have been received, that byte is moved to the SSPBUF
register. Then, the Buffer Full Detect bit, BF of the
SSPSTAT register, and the interrupt flag bit, SSPIF, are
set. This double-buffering of the received data
(SSPBUF) allows the next byte to start reception before
reading the data that was just received. Any write to the
SSPBUF register during transmission/reception of data
will be ignored and the write collision detect bit WCOL
of the SSPCON1 register, will be set. User software
must clear the WCOL bit to allow the following write(s)
to the SSPBUF register to complete successfully.
When the application software is expecting to receive
valid data, the SSPBUF should be read before the next
byte of data to transfer is written to the SSPBUF. The
Buffer Full bit, BF of the SSPSTAT register, indicates
when SSPBUF has been loaded with the received data
(transmission is complete). When the SSPBUF is read,
the BF bit is cleared. This data may be irrelevant if the
SPI is only a transmitter. Generally, the MSSP interrupt
is used to determine when the transmission/reception
has completed. If the interrupt method is not going to
be used, then software polling can be done to ensure
that a write collision does not occur.
The SSPSR is not directly readable or writable and can
only be accessed by addressing the SSPBUF register.
Additionally, the SSPSTAT register indicates the
various status conditions.
FIGURE 24-5: SPI MASTER/SLAVE CONNECTION
Serial Input Buffer
(BUF)
Shift Register
(SSPSR)
MSb LSb
SDO
SDI
Processor 1
SCK
SPI Master SSPM<3:0> = 00xx
Serial Input Buffer
(SSPBUF)
Shift Register
(SSPSR)
LSb
MSb
SDI
SDO
Processor 2
SCK
SPI Slave SSPM<3:0> = 010x
Serial Clock
SS
Slave Select
General I/O (optional)
= 1010
2008-2011 Microchip Technology Inc. DS41364E-page 245
PIC16(L)F1934/6/7
24.2.3 SPI MASTER MODE
The master can initiate the data transfer at any time
because it controls the SCK line. The master
determines when the slave (Processor 2, Figure 24-5)
is to broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and Status bits
appropriately set).
The clock polarity is selected by appropriately
programming the CKP bit of the SSPCON1 register
and the CKE bit of the SSPSTAT register. This then,
would give waveforms for SPI communication as
shown in Figure 24-6, Figure 24-8 and Figure 24-9,
where the MSB is transmitted first. In Master mode, the
SPI clock rate (bit rate) is user programmable to be one
of the following:
•F
OSC/4 (or TCY)
•FOSC/16 (or 4 * TCY)
•FOSC/64 (or 16 * TCY)
Timer2 output/2
Fosc/(4 * (SSPADD + 1))
Figure 24-6 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
FIGURE 24-6: SPI MODE WAVEFORM (MASTER MODE)
SCK
(CKP = 0
SCK
(CKP = 1
SCK
(CKP = 0
SCK
(CKP = 1
4 Clock
Modes
Input
Sample
Input
Sample
SDI
bit 7 bit 0
SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
bit 7
SDI
SSPIF
(SMP = 1)
(SMP = 0)
(SMP = 1)
CKE = 1)
CKE = 0)
CKE = 1)
CKE = 0)
(SMP = 0)
Write to
SSPBUF
SSPSR to
SSPBUF
SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
(CKE = 0)
(CKE = 1)
bit 0
PIC16(L)F1934/6/7
DS41364E-page 246 2008-2011 Microchip Technology Inc.
24.2.4 SPI SLAVE MODE
In Slave mode, the data is transmitted and received as
external clock pulses appear on SCK. When the last
bit is latched, the SSPIF interrupt flag bit is set.
Before enabling the module in SPI Slave mode, the clock
line must match the proper Idle state. The clock line can
be observed by reading the SCK pin. The Idle state is
determined by the CKP bit of the SSPCON1 register.
While in Slave mode, the external clock is supplied by
the external clock source on the SCK pin. This external
clock must meet the minimum high and low times as
specified in the electrical specifications.
While in Sleep mode, the slave can transmit/receive
data. The shift register is clocked from the SCK pin
input and when a byte is received, the device will gen-
erate an interrupt. If enabled, the device will wake-up
from Sleep.
24.2.4.1 Daisy-Chain Configuration
The SPI bus can sometimes be connected in a
daisy-chain configuration. The first slave output is
connected to the second slave input, the second slave
output is connected to the third slave input, and so on.
The final slave output is connected to the master input.
Each slave sends out, during a second group of clock
pulses, an exact copy of what was received during the
first group of clock pulses. The whole chain acts as one
large communication shift register. The daisy-chain
feature only requires a single Slave Select line from the
master device.
Figure 24-7 shows the block diagram of a typical
daisy-chain connection when operating in SPI Mode.
In a daisy-chain configuration, only the most recent
byte on the bus is required by the slave. Setting the
BOEN bit of the SSPCON3 register will enable writes
to the SSPBUF register, even if the previous byte has
not been read. This allows the software to ignore data
that may not apply to it.
24.2.5 SLAVE SELECT
SYNCHRONIZATION
The Slave Select can also be used to synchronize com-
munication. The Slave Select line is held high until the
master device is ready to communicate. When the
Slave Select line is pulled low, the slave knows that a
new transmission is starting.
If the slave fails to receive the communication properly,
it will be reset at the end of the transmission, when the
Slave Select line returns to a high state. The slave is
then ready to receive a new transmission when the
Slave Select line is pulled low again. If the Slave Select
line is not used, there is a risk that the slave will even-
tually become out of sync with the master. If the slave
misses a bit, it will always be one bit off in future trans-
missions. Use of the Slave Select line allows the slave
and master to align themselves at the beginning of
each transmission.
The SS pin allows a Synchronous Slave mode. The
SPI must be in Slave mode with SS pin control enabled
(SSPCON1<3:0> = 0100).
When the SS pin is low, transmission and reception are
enabled and the SDO pin is driven.
When the SS pin goes high, the SDO pin is no longer
driven, even if in the middle of a transmitted byte and
becomes a floating output. External pull-up/pull-down
resistors may be desirable depending on the applica-
tion.
When the SPI module resets, the bit counter is forced
to ‘0’. This can be done by either forcing the SS pin to
a high level or clearing the SSPEN bit.
Note 1: When the SPI is in Slave mode with SS pin
control enabled (SSPCON1<3:0> =
0100), the SPI module will reset if the SS
pin is set to VDD.
2: When the SPI is used in Slave mode with
CKE set; the user must enable SS pin
control.
3: While operated in SPI Slave mode the
SMP bit of the SSPSTAT register must
remain clear.
2008-2011 Microchip Technology Inc. DS41364E-page 247
PIC16(L)F1934/6/7
FIGURE 24-7: SPI DAISY-CHAIN CONNECTION
FIGURE 24-8: SLAVE SELECT SYNCHRONOUS WAVEFORM
SPI Master SCK
SDO
SDI
General I/O
SCK
SDI
SDO
SS
SPI Slave
#1
SCK
SDI
SDO
SS
SPI Slave
#2
SCK
SDI
SDO
SS
SPI Slave
#3
SCK
(CKP = 1
SCK
(CKP = 0
Input
Sample
SDI
bit 7
SDO bit 7 bit 6 bit 7
SSPIF
Interrupt
CKE = 0)
CKE = 0)
Write to
SSPBUF
SSPSR to
SSPBUF
SS
Flag
bit 0
bit 7
bit 0
bit 6
SSPBUF to
SSPSR
Shift register SSPSR
and bit count are reset
PIC16(L)F1934/6/7
DS41364E-page 248 2008-2011 Microchip Technology Inc.
FIGURE 24-9: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 0)
FIGURE 24-10: SPI MODE WAVEFORM (SLAVE MODE WITH CKE = 1)
SCK
(CKP = 1
SCK
(CKP = 0
Input
Sample
SDI
bit 7
SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
SSPIF
Interrupt
CKE = 0)
CKE = 0)
Write to
SSPBUF
SSPSR to
SSPBUF
SS
Flag
Optional
bit 0
detection active
Write Collision
Valid
SCK
(CKP = 1
SCK
(CKP = 0
Input
Sample
SDI
bit 7 bit 0
SDO bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0
SSPIF
Interrupt
CKE = 1)
CKE = 1)
Write to
SSPBUF
SSPSR to
SSPBUF
SS
Flag
Not Optional
Write Collision
detection active
Valid
2008-2011 Microchip Technology Inc. DS41364E-page 249
PIC16(L)F1934/6/7
24.2.6 SPI OPERATION IN SLEEP MODE
In SPI Master mode, module clocks may be operating
at a different speed than when in Full Power mode; in
the case of the Sleep mode, all clocks are halted.
Special care must be taken by the user when the MSSP
clock is much faster than the system clock.
In Slave mode, when MSSP interrupts are enabled,
after the master completes sending data, an MSSP
interrupt will wake the controller from Sleep.
If an exit from Sleep mode is not desired, MSSP
interrupts should be disabled.
In SPI Master mode, when the Sleep mode is selected,
all module clocks are halted and the transmis-
sion/reception will remain in that state until the device
wakes. After the device returns to Run mode, the mod-
ule will resume transmitting and receiving data.
In SPI Slave mode, the SPI Transmit/Receive Shift
register operates asynchronously to the device. This
allows the device to be placed in Sleep mode and data
to be shifted into the SPI Transmit/Receive Shift
register. When all 8 bits have been received, the MSSP
interrupt flag bit will be set and if enabled, will wake the
device.
TABLE 24-1: SUMMARY OF REGISTERS ASSOCIATED WITH SPI OPERATION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 B it 0 Register
on Pag e
ANSELA ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 134
APFCON CCP3SEL T1GSEL P2BSEL SRNQSEL C2OUTSEL SSSEL CCP2SEL 131
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSP1IE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSP1IF CCP1IF TMR2IF TMR1IF 102
SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register 243*
SSPCON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 287
SSPCON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 289
SSPSTAT SMP CKE D/A P S R/W UA BF 286
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISB2 TRISC1 TRISC0 142
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the MSSP in SPI mode.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 250 2008-2011 Microchip Technology Inc.
24.3 I2C Mode Overview
The Inter-Integrated Circuit Bus (I2C) is a multi-master
serial data communication bus. Devices communicate
in a master/slave environment where the master
devices initiate the communication. A Slave device is
controlled through addressing.
The I2C bus specifies two signal connections:
Serial Clock (SCL)
Serial Data (SDA)
Figure 24-11 shows the block diagram of the MSSP
module when operating in I2C Mode.
Both the SCL and SDA connections are bidirectional
open-drain lines, each requiring pull-up resistors for the
supply voltage. Pulling the line to ground is considered
a logical zero and letting the line float is considered a
logical one.
Figure 24-11 shows a typical connection between two
processors configured as master and slave devices.
The I2C bus can operate with one or more master
devices and one or more slave devices.
There are four potential modes of operation for a given
device:
Master Transmit mode
(master is transmitting data to a slave)
Master Receive mode
(master is receiving data from a slave)
•Slave Transmit mode
(slave is transmitting data to a master)
Slave Receive mode
(slave is receiving data from the master)
To begin communication, a master device starts out in
Master Transmit mode. The master device sends out a
Start bit followed by the address byte of the slave it
intends to communicate with. This is followed by a sin-
gle Read/Write bit, which determines whether the mas-
ter intends to transmit to or receive data from the slave
device.
If the requested slave exists on the bus, it will respond
with an Acknowledge bit, otherwise known as an ACK.
The master then continues in either Transmit mode or
Receive mode and the slave continues in the comple-
ment, either in Receive mode or Transmit mode,
respectively.
A Start bit is indicated by a high-to-low transition of the
SDA line while the SCL line is held high. Address and
data bytes are sent out, Most Significant bit (MSb) first.
The Read/Write bit is sent out as a logical one when the
master intends to read data from the slave, and is sent
out as a logical zero when it intends to write data to the
slave.
FIGURE 24-11: I2C MASTER/
SLAVE CONNECTION
The Acknowledge bit (ACK) is an active-low signal,
which holds the SDA line low to indicate to the transmit-
ter that the slave device has received the transmitted
data and is ready to receive more.
The transition of a data bit is always performed while
the SCL line is held low. Transitions that occur while the
SCL line is held high are used to indicate Start and Stop
bits.
If the master intends to write to the slave, then it repeat-
edly sends out a byte of data, with the slave responding
after each byte with an ACK bit. In this example, the
master device is in Master Transmit mode and the
slave is in Slave Receive mode.
If the master intends to read from the slave, then it
repeatedly receives a byte of data from the slave, and
responds after each byte with an ACK bit. In this exam-
ple, the master device is in Master Receive mode and
the slave is Slave Transmit mode.
On the last byte of data communicated, the master
device may end the transmission by sending a Stop bit.
If the master device is in Receive mode, it sends the
Stop bit in place of the last ACK bit. A Stop bit is indi-
cated by a low-to-high transition of the SDA line while
the SCL line is held high.
In some cases, the master may want to maintain con-
trol of the bus and re-initiate another transmission. If
so, the master device may send another Start bit in
place of the Stop bit or last ACK bit when it is in receive
mode.
The I2C bus specifies three message protocols;
Single message where a master writes data to a
slave.
Single message where a master reads data from
a slave.
Combined message where a master initiates a
minimum of two writes, or two reads, or a
combination of writes and reads, to one or more
slaves.
Master
SCL
SDA
SCL
SDA
Slave
VDD
VDD
2008-2011 Microchip Technology Inc. DS41364E-page 251
PIC16(L)F1934/6/7
When one device is transmitting a logical one, or letting
the line float, and a second device is transmitting a log-
ical zero, or holding the line low, the first device can
detect that the line is not a logical one. This detection,
when used on the SCL line, is called clock stretching.
Clock stretching gives slave devices a mechanism to
control the flow of data. When this detection is used on
the SDA line, it is called arbitration. Arbitration ensures
that there is only one master device communicating at
any single time.
24.3.1 CLOCK STRETCHING
When a slave device has not completed processing
data, it can delay the transfer of more data through the
process of clock stretching. An addressed slave device
may hold the SCL clock line low after receiving or send-
ing a bit, indicating that it is not yet ready to continue.
The master that is communicating with the slave will
attempt to raise the SCL line in order to transfer the
next bit, but will detect that the clock line has not yet
been released. Because the SCL connection is
open-drain, the slave has the ability to hold that line low
until it is ready to continue communicating.
Clock stretching allows receivers that cannot keep up
with a transmitter to control the flow of incoming data.
24.3.2 ARBITRATION
Each master device must monitor the bus for Start and
Stop bits. If the device detects that the bus is busy, it
cannot begin a new message until the bus returns to an
Idle state.
However, two master devices may try to initiate a trans-
mission on or about the same time. When this occurs,
the process of arbitration begins. Each transmitter
checks the level of the SDA data line and compares it
to the level that it expects to find. The first transmitter to
observe that the two levels do not match, loses arbitra-
tion, and must stop transmitting on the SDA line.
For example, if one transmitter holds the SDA line to a
logical one (lets it float) and a second transmitter holds
it to a logical zero (pulls it low), the result is that the
SDA line will be low. The first transmitter then observes
that the level of the line is different than expected and
concludes that another transmitter is communicating.
The first transmitter to notice this difference is the one
that loses arbitration and must stop driving the SDA
line. If this transmitter is also a master device, it also
must stop driving the SCL line. It then can monitor the
lines for a Stop condition before trying to reissue its
transmission. In the meantime, the other device that
has not noticed any difference between the expected
and actual levels on the SDA line continues with its
original transmission. It can do so without any compli-
cations, because so far, the transmission appears
exactly as expected with no other transmitter disturbing
the message.
Slave Transmit mode can also be arbitrated, when a
master addresses multiple slaves, but this is less com-
mon.
If two master devices are sending a message to two dif-
ferent slave devices at the address stage, the master
sending the lower slave address always wins arbitra-
tion. When two master devices send messages to the
same slave address, and addresses can sometimes
refer to multiple slaves, the arbitration process must
continue into the data stage.
Arbitration usually occurs very rarely, but it is a neces-
sary process for proper multi-master support.
24.4 I2C™ Mode Operation
All MSSP I2C communication is byte oriented and
shifted out MSb first. Six SFR registers and 2 interrupt
flags interface the module with the PIC® microcon-
troller and user software. Two pins, SDA and SCL, are
exercised by the module to communicate with other
external I2C devices.
24.4.1 BYTE FORMAT
All communication in I2C is done in 9-bit segments. A
byte is sent from a Master to a Slave or vice-versa, fol-
lowed by an Acknowledge bit sent back. After the 8th
falling edge of the SCL line, the device outputting data
on the SDA changes that pin to an input and reads in
an Acknowledge value on the next clock pulse.
The clock signal, SCL, is provided by the master. Data
is valid to change while the SCL signal is low, and
sampled on the rising edge of the clock. Changes on
the SDA line while the SCL line is high define special
conditions on the bus, explained below.
24.4.2 DEFINITION OF I2C TERMINOLOGY
There is language and terminology in the description
of I2C communication that have definitions specific to
I2C. That word usage is defined below and may be
used in the rest of this document without explana-
tion. This table was adapted from the Philips I2C
specification.
24.4.3 SDA AND SCL PINS
Selection of any I2C mode with the SSPEN bit set,
forces the SCL and SDA pins to be open-drain. These
pins should be set by the user to inputs by setting the
appropriate TRIS bits.
24.4.4 SDA HOLD TIME
The hold time of the SDA pin is selected by the SDAHT
bit of the SSPCON3 register. Hold time is the time SDA
is held valid after the falling edge of SCL. Setting the
SDAHT bit selects a longer 300 ns minimum hold time
and may help on buses with large capacitance.
Note: Data is tied to output zero when an I2C
mode is enabled.
PIC16(L)F1934/6/7
DS41364E-page 252 2008-2011 Microchip Technology Inc.
TABLE 24-2: I2C BUS TERMS 24.4.5 START CONDITION
The I2C specification defines a Start condition as a
transition of SDA from a high to a low state while SCL
line is high. A Start condition is always generated by
the master and signifies the transition of the bus from
an Idle to an Active state. Figure 24-10 shows wave
forms for Start and Stop conditions.
A bus collision can occur on a Start condition if the
module samples the SDA line low before asserting it
low. This does not conform to the I2C specification that
states no bus collision can occur on a Start.
24.4.6 STOP CONDITION
A Stop condition is a transition of the SDA line from
low-to-high state while the SCL line is high.
24.4.7 RESTART CONDITION
A Restart is valid any time that a Stop would be valid.
A master can issue a Restart if it wishes to hold the
bus after terminating the current transfer. A Restart
has the same effect on the slave that a Start would,
resetting all slave logic and preparing it to clock in an
address. The master may want to address the same or
another slave.
In 10-bit Addressing Slave mode a Restart is required
for the master to clock data out of the addressed
slave. Once a slave has been fully addressed, match-
ing both high and low address bytes, the master can
issue a Restart and the high address byte with the
R/W bit set. The slave logic will then hold the clock
and prepare to clock out data.
After a full match with R/W clear in 10-bit mode, a prior
match flag is set and maintained. Until a Stop condi-
tion, a high address with R/W clear, or high address
match fails.
24.4.8 START/STOP CONDITION
INTERRUPT MASKING
The SCIE and PCIE bits of the SSPCON3 register can
enable the generation of an interrupt in Slave modes
that do not typically support this function. Slave modes
where interrupt on Start and Stop detect are already
enabled, these bits will have no effect.
TERM Description
Transmitter The device which shifts data out
onto the bus.
Receiver The device which shifts data in
from the bus.
Master The device that initiates a transfer,
generates clock signals and termi-
nates a transfer.
Slave The device addressed by the mas-
ter.
Multi-master A bus with more than one device
that can initiate data transfers.
Arbitration Procedure to ensure that only one
master at a time controls the bus.
Winning arbitration ensures that
the message is not corrupted.
Synchronization Procedure to synchronize the
clocks of two or more devices on
the bus.
Idle No master is controlling the bus,
and both SDA and SCL lines are
high.
Active Any time one or more master
devices are controlling the bus.
Addressed
Slave
Slave device that has received a
matching address and is actively
being clocked by a master.
Matching
Address
Address byte that is clocked into a
slave that matches the value
stored in SSPADD.
Write Request Slave receives a matching
address with R/W bit clear, and is
ready to clock in data.
Read Request Master sends an address byte with
the R/W bit set, indicating that it
wishes to clock data out of the
Slave. This data is the next and all
following bytes until a Restart or
Stop.
Clock Stretching When a device on the bus hold
SCL low to stall communication.
Bus Collision Any time the SDA line is sampled
low by the module while it is out-
putting and expected high state.
Note: At least one SCL low time must appear
before a Stop is valid, therefore, if the SDA
line goes low then high again while the SCL
line stays high, only the Start condition is
detected.
2008-2011 Microchip Technology Inc. DS41364E-page 253
PIC16(L)F1934/6/7
FIGURE 24-12 : I2C START AND STOP CONDITIONS
FIGURE 24-13 : I2C RESTART CONDITION
SDA
SCL
P
Stop
Condition
S
Start
Condition
Change of
Data Allowed
Change of
Data Allowed
Restart
Condition
Sr
Change of
Data Allowed
Change of
Data Allowed
PIC16(L)F1934/6/7
DS41364E-page 254 2008-2011 Microchip Technology Inc.
24.4.9 ACKNOWLEDGE SEQUENCE
The 9th SCL pulse for any transferred byte in I2C is
dedicated as an Acknowledge. It allows receiving
devices to respond back to the transmitter by pulling
the SDA line low. The transmitter must release control
of the line during this time to shift in the response. The
Acknowledge (ACK) is an active-low signal, pulling the
SDA line low indicated to the transmitter that the
device has received the transmitted data and is ready
to receive more.
The result of an ACK is placed in the ACKSTAT bit of
the SSPCON2 register.
Slave software, when the AHEN and DHEN bits are
set, allow the user to set the ACK value sent back to
the transmitter. The ACKDT bit of the SSPCON2 regis-
ter is set/cleared to determine the response.
Slave hardware will generate an ACK response if the
AHEN and DHEN bits of the SSPCON3 register are
clear.
There are certain conditions where an ACK will not be
sent by the slave. If the BF bit of the SSPSTAT register
or the SSPOV bit of the SSPCON1 register are set
when a byte is received.
When the module is addressed, after the 8th falling
edge of SCL on the bus, the ACKTIM bit of the
SSPCON3 register is set. The ACKTIM bit indicates
the acknowledge time of the active bus. The ACKTIM
Status bit is only active when the AHEN bit or DHEN
bit is enabled.
24.5 I2C Slave Mode Operation
The MSSP Slave mode operates in one of four modes
selected in the SSPM bits of SSPCON1 register. The
modes can be divided into 7-bit and 10-bit Addressing
mode. 10-bit Addressing modes operate the same as
7-bit with some additional overhead for handling the
larger addresses.
Modes with Start and Stop bit interrupts operated the
same as the other modes with SSPIF additionally get-
ting set upon detection of a Start, Restart, or Stop
condition.
24.5.1 SLAVE MODE ADDRESSES
The SSPADD register (Register 24-6) contains the
Slave mode address. The first byte received after a
Start or Restart condition is compared against the
value stored in this register. If the byte matches, the
value is loaded into the SSPBUF register and an inter-
rupt is generated. If the value does not match, the
module goes Idle and no indication is given to the soft-
ware that anything happened.
The SSP Mask register (Register 24-5) affects the
address matching process. See Section 24.5.9 “SSP
Mask Register” for more information.
24.5.1.1 I2C Slave 7-bit Addressing Mode
In 7-bit Addressing mode, the LSb of the received data
byte is ignored when determining if there is an address
match.
24.5.1.2 I2C Slave 10-bit Addressing Mode
In 10-bit Addressing mode, the first received byte is
compared to the binary value of ‘1 1 1 1 0 A9 A8 0’. A9
and A8 are the two MSb of the 10-bit address and
stored in bits 2 and 1 of the SSPADD register.
After the acknowledge of the high byte the UA bit is set
and SCL is held low until the user updates SSPADD
with the low address. The low address byte is clocked
in and all 8 bits are compared to the low address value
in SSPADD. Even if there is not an address match;
SSPIF and UA are set, and SCL is held low until
SSPADD is updated to receive a high byte again.
When SSPADD is updated the UA bit is cleared. This
ensures the module is ready to receive the high
address byte on the next communication.
A high and low address match as a write request is
required at the start of all 10-bit addressing communi-
cation. A transmission can be initiated by issuing a
Restart once the slave is addressed, and clocking in
the high address with the R/W bit set. The slave hard-
ware will then acknowledge the read request and pre-
pare to clock out data. This is only valid for a slave
after it has received a complete high and low address
byte match.
2008-2011 Microchip Technology Inc. DS41364E-page 255
PIC16(L)F1934/6/7
24.5.2 SLAVE RECEPTION
When the R/W bit of a matching received address byte
is clear, the R/W bit of the SSPSTAT register is cleared.
The received address is loaded into the SSPBUF reg-
ister and acknowledged.
When the overflow condition exists for a received
address, then not Acknowledge is given. An overflow
condition is defined as either bit BF bit of the SSPSTAT
register is set, or bit SSPOV bit of the SSPCON1 reg-
ister is set. The BOEN bit of the SSPCON3 register
modifies this operation. For more information see
Register 24-4.
An MSSP interrupt is generated for each transferred
data byte. Flag bit, SSPIF, must be cleared by software.
When the SEN bit of the SSPCON2 register is set, SCL
will be held low (clock stretch) following each received
byte. The clock must be released by setting the CKP
bit of the SSPCON1 register, except sometimes in
10-bit mode. See Section 24.2.3 “SPI Master Mode”
for more detail.
24.5.2.1 7-bit Addressing Reception
This section describes a standard sequence of events
for the MSSP module configured as an I2C Slave in
7-bit Addressing mode. All decisions made by hard-
ware or software and their effect on reception.
Figure 24-13 and Figure 24-14 is used as a visual
reference for this description.
This is a step by step process of what typically must
be done to accomplish I2C communication.
1. Start bit detected.
2. S bit of SSPSTAT is set; SSPIF is set if interrupt
on Start detect is enabled.
3. Matching address with R/W bit clear is received.
4. The slave pulls SDA low sending an ACK to the
master, and sets SSPIF bit.
5. Software clears the SSPIF bit.
6. Software reads received address from SSPBUF
clearing the BF flag.
7. If SEN = 1; Slave software sets CKP bit to
release the SCL line.
8. The master clocks out a data byte.
9. Slave drives SDA low sending an ACK to the
master, and sets SSPIF bit.
10. Software clears SSPIF.
11. Software reads the received byte from SSPBUF
clearing BF.
12. Steps 8-12 are repeated for all received bytes
from the Master.
13. Master sends Stop condition, setting P bit of
SSPSTAT, and the bus goes Idle.
24.5.2.2 7-bit Reception with AHEN and
DHEN
Slave device reception with AHEN and DHEN set
operate the same as without these options with extra
interrupts and clock stretching added after the 8th fall-
ing edge of SCL. These additional interrupts allow the
slave software to decide whether it wants to ACK the
receive address or data byte, rather than the hard-
ware. This functionality adds support for PMBus™ that
was not present on previous versions of this module.
This list describes the steps that need to be taken by
slave software to use these options for I2C communi-
cation. Figure 24-15 displays a module using both
address and data holding. Figure 24-16 includes the
operation with the SEN bit of the SSPCON2 register
set.
1. S bit of SSPSTAT is set; SSPIF is set if interrupt
on Start detect is enabled.
2. Matching address with R/W bit clear is clocked
in. SSPIF is set and CKP cleared after the 8th
falling edge of SCL.
3. Slave clears the SSPIF.
4. Slave can look at the ACKTIM bit of the
SSPCON3 register to determine if the SSPIF
was after or before the ACK.
5. Slave reads the address value from SSPBUF,
clearing the BF flag.
6. Slave sets ACK value clocked out to the master
by setting ACKDT.
7. Slave releases the clock by setting CKP.
8. SSPIF is set after an ACK, not after a NACK.
9. If SEN = 1 the slave hardware will stretch the
clock after the ACK.
10. Slave clears SSPIF.
11. SSPIF set and CKP cleared after 8th falling
edge of SCL for a received data byte.
12. Slave looks at ACKTIM bit of SSPCON3 to
determine the source of the interrupt.
13. Slave reads the received data from SSPBUF
clearing BF.
14. Steps 7-14 are the same for each received data
byte.
15. Communication is ended by either the slave
sending an ACK =1, or the master sending a
Stop condition. If a Stop is sent and Interrupt on
Stop Detect is disabled, the slave will only know
by polling the P bit of the SSTSTAT register.
Note: SSPIF is still set after the 9th falling edge of
SCL even if there is no clock stretching and
BF has been cleared. Only if NACK is sent
to Master is SSPIF not set
PIC16(L)F1934/6/7
DS41364E-page 256 2008-2011 Microchip Technology Inc.
FIGURE 24-14 : I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 0, AHEN = 0, DHEN = 0)
Receiving Address
ACK
Receiving Data
ACK
Receiving Data ACK =1
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
SDA
SCL
SSPIF
BF
SSPOV
12345678 12345678 12345678
999
ACK is not sent.
SSPOV set because
SSPBUF is still full.
Cleared by software
First byte
of data is
available
in SSPBUF
SSPBUF is read
SSPIF set on 9th
falling edge of
SCL
Cleared by software
P
Bus Master sends
Stop condition
S
From Slave to Master
2008-2011 Microchip Technology Inc. DS41364E-page 257
PIC16(L)F1934/6/7
FIGURE 24-15 : I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 1, AHEN = 0, DHEN = 0)
SEN SEN
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0SDA
SCL 123456789 123456789 123456789 P
SSPIF set on 9th
SCL is not held
CKP is written to 1 in software,
CKP is written to 1’ in software,
ACK
low because
falling edge of SCL
releasing SCL
ACK is not sent.
Bus Master sends
CKP
SSPOV
BF
SSPIF
SSPOV set because
SSPBUF is still full.
Cleared by software
First byte
of data is
available
in SSPBUF
ACK=1
Cleared by software
SSPBUF is read
Clock is held low until CKP is set to ‘1
releasing SCL
Stop condition
S
ACK
ACK
Receive Address Receive Data Receive Data
R/W=0
PIC16(L)F1934/6/7
DS41364E-page 258 2008-2011 Microchip Technology Inc.
FIGURE 24-16 : I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 0, AHEN = 1, DHEN = 1)
Receiving Address Receiving Data Received Data
P
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
SDA
SCL
BF
CKP
S
P
12 3 4 56 7 8 912345678 9
12345678
Master sends
Stop condition
S
Data is read from SSPBUF
Cleared by software
SSPIF is set on
9th falling edge of
SCL, after ACK
CKP set by software,
SCL is released
Slave software
9
ACKTIM cleared by
hardware in 9th
rising edge of SCL
sets ACKDT to
not ACK
When DHEN=1:
CKP is cleared by
hardware on 8th falling
edge of SCL
Slave software
clears ACKDT to
ACK the received
byte
ACKTIM set by hardware
on 8th falling edge of SCL
When AHEN=1:
CKP is cleared by hardware
and SCL is stretched
Address is
read from
SSBUF
ACKTIM set by hardware
on 8th falling edge of SCL
ACK
Master Releases SDA
to slave for ACK sequence
No interrupt
after not ACK
from Slave
ACK=1
ACK
ACKDT
ACKTIM
SSPIF
If AHEN = 1:
SSPIF is set
2008-2011 Microchip Technology Inc. DS41364E-page 259
PIC16(L)F1934/6/7
FIGURE 24-17 : I2C SLAVE, 7-BIT ADDRESS, RECEPTION (SEN = 1, AHEN = 1, DHEN = 1)
Receiving Address Receive Data Receive Data
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
SDA
SCL
SSPIF
BF
ACKDT
CKP
S
P
ACK
S12
345678 912
345678 9 12345 67 8 9
ACK
ACK
Cleared by software
ACKTIM is cleared by hardware
SSPBUF can be
Set by software,
read any time before
next byte is loaded
release SCL
on 9th rising edge of SCL
Received
address is loaded into
SSPBUF
Slave software clears
ACKDT to ACK
R/W = 0Master releases
SDA to slave for ACK sequence
the received byte
When AHEN = 1;
on the 8th falling edge
of SCL of an address
byte, CKP is cleared
ACKTIM is set by hardware
on 8th falling edge of SCL
When DHEN = 1;
on the 8th falling edge
of SCL of a received
data byte, CKP is cleared
Received data is
available on SSPBUF
Slave sends
not ACK
CKP is not cleared
if not ACK
P
Master sends
Stop condition
No interrupt after
if not ACK
from Slave
ACKTIM
PIC16(L)F1934/6/7
DS41364E-page 260 2008-2011 Microchip Technology Inc.
24.5.3 SLAVE TRANSMISSION
When the R/W bit of the incoming address byte is set
and an address match occurs, the R/W bit of the
SSPSTAT register is set. The received address is
loaded into the SSPBUF register, and an ACK pulse is
sent by the slave on the ninth bit.
Following the ACK, slave hardware clears the CKP bit
and the SCL pin is held low (see Section 24.5.6
“Clock Stretching” for more detail). By stretching the
clock, the master will be unable to assert another clock
pulse until the slave is done preparing the transmit
data.
The transmit data must be loaded into the SSPBUF
register which also loads the SSPSR register. Then the
SCL pin should be released by setting the CKP bit of
the SSPCON1 register. The eight data bits are shifted
out on the falling edge of the SCL input. This ensures
that the SDA signal is valid during the SCL high time.
The ACK pulse from the master-receiver is latched on
the rising edge of the ninth SCL input pulse. This ACK
value is copied to the ACKSTAT bit of the SSPCON2
register. If ACKSTAT is set (not ACK), then the data
transfer is complete. In this case, when the not ACK is
latched by the slave, the slave goes Idle and waits for
another occurrence of the Start bit. If the SDA line was
low (ACK), the next transmit data must be loaded into
the SSPBUF register. Again, the SCL pin must be
released by setting bit CKP.
An MSSP interrupt is generated for each data transfer
byte. The SSPIF bit must be cleared by software and
the SSPSTAT register is used to determine the status
of the byte. The SSPIF bit is set on the falling edge of
the ninth clock pulse.
24.5.3.1 Slave Mode Bus Collision
A slave receives a Read request and begins shifting
data out on the SDA line. If a bus collision is detected
and the SBCDE bit of the SSPCON3 register is set, the
BCLIF bit of the PIR register is set. Once a bus collision
is detected, the slave goes Idle and waits to be
addressed again. User software can use the BCLIF bit
to handle a slave bus collision.
24.5.3.2 7-bit Transmission
A master device can transmit a read request to a
slave, and then clock data out of the slave. The list
below outlines what software for a slave will need to
do to accomplish a standard transmission.
Figure 24-17 can be used as a reference to this list.
1. Master sends a Start condition on SDA and
SCL.
2. S bit of SSPSTAT is set; SSPIF is set if interrupt
on Start detect is enabled.
3. Matching address with R/W bit set is received by
the Slave setting SSPIF bit.
4. Slave hardware generates an ACK and sets
SSPIF.
5. SSPIF bit is cleared by user.
6. Software reads the received address from
SSPBUF, clearing BF.
7. R/W is set so CKP was automatically cleared
after the ACK.
8. The slave software loads the transmit data into
SSPBUF.
9. CKP bit is set releasing SCL, allowing the
master to clock the data out of the slave.
10. SSPIF is set after the ACK response from the
master is loaded into the ACKSTAT register.
11. SSPIF bit is cleared.
12. The slave software checks the ACKSTAT bit to
see if the master wants to clock out more data.
13. Steps 9-13 are repeated for each transmitted
byte.
14. If the master sends a not ACK; the clock is not
held, but SSPIF is still set.
15. The master sends a Restart condition or a Stop.
16. The slave is no longer addressed.
Note 1: If the master ACKs the clock will be
stretched.
2: ACKSTAT is the only bit updated on the
rising edge of SCL (9th) rather than the
falling.
2008-2011 Microchip Technology Inc. DS41364E-page 261
PIC16(L)F1934/6/7
FIGURE 24-18 : I2C SLAVE, 7-BIT ADDRESS, TRANSMISSION (AHEN = 0)
Receiving Address Automatic Transmitting Data Automatic Transmitting Data
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
SDA
SCL
SSPIF
BF
CKP
ACKSTAT
R/W
D/A
S
P
Received address
When R/W is set
R/W is copied from the
Indicates an address
is read from SSPBUF
SCL is always
held low after 9th SCL
falling edge
matching address byte
has been received
Masters not ACK
is copied to
ACKSTAT
CKP is not
held for not
ACK
BF is automatically
cleared after 8th falling
edge of SCL
Data to transmit is
loaded into SSPBUF
Set by software
Cleared by software
ACK
ACK
ACK
R/W = 1
SP
Master sends
Stop condition
PIC16(L)F1934/6/7
DS41364E-page 262 2008-2011 Microchip Technology Inc.
24.5.3.3 7-bit Transmission with Address
Hold Enabled
Setting the AHEN bit of the SSPCON3 register
enables additional clock stretching and interrupt
generation after the 8th falling edge of a received
matching address. Once a matching address has
been clocked in, CKP is cleared and the SSPIF
interrupt is set.
Figure 24-18 displays a standard waveform of a 7-bit
Address Slave Transmission with AHEN enabled.
1. Bus starts Idle.
2. Master sends Start condition; the S bit of
SSPSTAT is set; SSPIF is set if interrupt on Start
detect is enabled.
3. Master sends matching address with R/W bit
set. After the 8th falling edge of the SCL line the
CKP bit is cleared and SSPIF interrupt is gener-
ated.
4. Slave software clears SSPIF.
5. Slave software reads ACKTIM bit of SSPCON3
register, and R/W and D/A of the SSPSTAT reg-
ister to determine the source of the interrupt.
6. Slave reads the address value from the
SSPBUF register clearing the BF bit.
7. Slave software decides from this information if it
wishes to ACK or not ACK and sets ACKDT bit
of the SSPCON2 register accordingly.
8. Slave sets the CKP bit releasing SCL.
9. Master clocks in the ACK value from the slave.
10. Slave hardware automatically clears the CKP bit
and sets SSPIF after the ACK if the R/W bit is
set.
11. Slave software clears SSPIF.
12. Slave loads value to transmit to the master into
SSPBUF setting the BF bit.
13. Slave sets CKP bit releasing the clock.
14. Master clocks out the data from the slave and
sends an ACK value on the 9th SCL pulse.
15. Slave hardware copies the ACK value into the
ACKSTAT bit of the SSPCON2 register.
16. Steps 10-15 are repeated for each byte transmit-
ted to the master from the slave.
17. If the master sends a not ACK the slave
releases the bus allowing the master to send a
Stop and end the communication.
Note: SSPBUF cannot be loaded until after the
ACK.
Note: Master must send a not ACK on the last byte
to ensure that the slave releases the SCL
line to receive a Stop.
2008-2011 Microchip Technology Inc. DS41364E-page 263
PIC16(L)F1934/6/7
FIGURE 24-19 : I2C SLAVE, 7-BIT ADDRESS, TRANSMISSION (AHEN = 1)
Receiving Address Automatic Transmitting Data Automatic Transmitting Data
A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
SDA
SCL
SSPIF
BF
ACKDT
ACKSTAT
CKP
R/W
D/A
Received address
is read from SSPBUF
BF is automatically
cleared after 8th falling
edge of SCL
Data to transmit is
loaded into SSPBUF
Cleared by software
Slave clears
ACKDT to ACK
address
Master’s ACK
response is copied
to SSPSTAT
CKP not cleared
after not ACK
Set by software,
releases SCL
ACKTIM is cleared
on 9th rising edge of SCL
ACKTIM is set on 8th falling
edge of SCL
When AHEN = 1;
CKP is cleared by hardware
after receiving matching
address.
When R/W = 1;
CKP is always
cleared after ACK
SP
Master sends
Stop condition
ACK
R/W = 1
Master releases SDA
to slave for ACK sequence
ACK
ACK
ACKTIM
PIC16(L)F1934/6/7
DS41364E-page 264 2008-2011 Microchip Technology Inc.
24.5.4 SLAVE MODE 10-BIT ADDRESS
RECEPTION
This section describes a standard sequence of events
for the MSSP module configured as an I2C Slave in
10-bit Addressing mode.
Figure 24-19 is used as a visual reference for this
description.
This is a step by step process of what must be done by
slave software to accomplish I2C communication.
1. Bus starts Idle.
2. Master sends Start condition; S bit of SSPSTAT
is set; SSPIF is set if interrupt on Start detect is
enabled.
3. Master sends matching high address with R/W
bit clear; UA bit of the SSPSTAT register is set.
4. Slave sends ACK and SSPIF is set.
5. Software clears the SSPIF bit.
6. Software reads received address from SSPBUF
clearing the BF flag.
7. Slave loads low address into SSPADD,
releasing SCL.
8. Master sends matching low address byte to the
Slave; UA bit is set.
9. Slave sends ACK and SSPIF is set.
10. Slave clears SSPIF.
11. Slave reads the received matching address
from SSPBUF clearing BF.
12. Slave loads high address into SSPADD.
13. Master clocks a data byte to the slave and
clocks out the slaves ACK on the 9th SCL pulse;
SSPIF is set.
14. If SEN bit of SSPCON2 is set, CKP is cleared by
hardware and the clock is stretched.
15. Slave clears SSPIF.
16. Slave reads the received byte from SSPBUF
clearing BF.
17. If SEN is set the slave sets CKP to release the
SCL.
18. Steps 13-17 repeat for each received byte.
19. Master sends Stop to end the transmission.
24.5.5 10-BIT ADDRESSING WITH
ADDRESS OR DATA HOLD
Reception using 10-bit addressing with AHEN or
DHEN set is the same as with 7-bit modes. The only
difference is the need to update the SSPADD register
using the UA bit. All functionality, specifically when the
CKP bit is cleared and SCL line is held low are the
same. Figure 24-20 can be used as a reference of a
slave in 10-bit addressing with AHEN set.
Figure 24-21 shows a standard waveform for a slave
transmitter in 10-bit Addressing mode.
Note: Updates to the SSPADD register are not
allowed until after the ACK sequence.
Note: If the low address does not match, SSPIF
and UA are still set so that the slave soft-
ware can set SSPADD back to the high
address. BF is not set because there is no
match. CKP is unaffected.
2008-2011 Microchip Technology Inc. DS41364E-page 265
PIC16(L)F1934/6/7
FIGURE 24-20 : I2C SLAVE, 10-BIT ADDRESS, RECEPTION (SEN = 1, AHEN = 0, DHEN = 0)
SSPIF
Receive First Address Byte
ACK
Receive Second Address Byte
ACK
Receive Data
ACK
Receive Data
ACK
1 1 1 1 0
A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
SDA
SCL
UA
CKP
12345678912345678
912345678
9123456789P
Master sends
Stop condition
Cleared by software
Receive address is
Software updates SSPADD
Data is read
SCL is held low
Set by software,
while CKP =
0
from SSPBUF
releasing SCL
When SEN =
1
;
CKP is cleared after
9th falling edge of received byte
read from SSPBUF
and releases SCL
When UA =
1
;
If address matches
Set by hardware
on 9th falling edge
SSPADD it is loaded into
SSPBUF
SCL is held low
S
BF
PIC16(L)F1934/6/7
DS41364E-page 266 2008-2011 Microchip Technology Inc.
FIGURE 24-21 : I2C SLAVE, 10-BIT ADDRESS, RECEPTION (SEN = 0, AHEN = 1, DHEN = 0)
Receive First Address Byte
UA
Receive Second Address Byte
UA
Receive Data
ACK
Receive Data
1 1 1 1 0
A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5SDA
SCL
SSPIF
BF
ACKDT
UA
CKP
ACKTIM
12345678 9
S
ACK
ACK
12345678 91234567891
2
SSPBUF
is read from
Received data
SSPBUF can be
read anytime before
the next received byte
Cleared by software
falling edge of SCL
not allowed until 9th
Update to SSPADD is
Set CKP with software
releases SCL
SCL
clears UA and releases
Update of SSPADD,
Set by hardware
on 9th falling edge
Slave software clears
ACKDT to ACK
the received byte
If when AHEN = 1;
on the 8th falling edge
of SCL of an address
byte, CKP is cleared
ACKTIM is set by hardware
on 8th falling edge of SCL
Cleared by software
R/W = 0
2008-2011 Microchip Technology Inc. DS41364E-page 267
PIC16(L)F1934/6/7
FIGURE 24-22 : I2C SLAVE, 10-BIT ADDRESS, TRANSMISSION (SEN = 0, AHEN = 0, DHEN = 0)
Receiving Address
ACK
Receiving Second Address Byte
Sr
Receive First Address Byte
ACK
Transmitting Data Byte
1 1 1 1 0
A9 A8 A7 A6 A5 A4 A3 A2 A1 A0
1 1 1 1 0
A9 A8 D7 D6 D5 D4 D3 D2 D1 D0SDA
SCL
SSPIF
BF
UA
CKP
R/W
D/A
123456789 123456789 123 4 56789 123456789
ACK = 1
P
Master sends
Stop condition
Master sends
not ACK
Master sends
Restart event
ACK
R/W = 0
S
Cleared by software
After SSPADD is
updated, UA is cleared
and SCL is released
High address is loaded
Received address is Data to transmit is
Set by software
Indicates an address
When R/W = 1;
R/W is copied from the
Set by hardware
UA indicates SSPADD
SSPBUF loaded
with received address
must be updated
has been received
loaded into SSPBUF
releases SCL
Masters not ACK
is copied
matching address byte
CKP is cleared on
9th falling edge of SCL
read from SSPBUF
back into SSPADD
ACKSTAT
Set by hardware
PIC16(L)F1934/6/7
DS41364E-page 268 2008-2011 Microchip Technology Inc.
24.5.6 CLOCK STRETCHING
Clock stretching occurs when a device on the bus
holds the SCL line low, effectively pausing communi-
cation. The slave may stretch the clock to allow more
time to handle data or prepare a response for the mas-
ter device. A master device is not concerned with
stretching as anytime it is active on the bus and not
transferring data it is stretching. Any stretching done
by a slave is invisible to the master software and han-
dled by the hardware that generates SCL.
The CKP bit of the SSPCON1 register is used to con-
trol stretching in software. Any time the CKP bit is
cleared, the module will wait for the SCL line to go low
and then hold it. Setting CKP will release SCL and
allow more communication.
24.5.6.1 Normal Clock Stretching
Following an ACK if the R/W bit of SSPSTAT is set, a
read request, the slave hardware will clear CKP. This
allows the slave time to update SSPBUF with data to
transfer to the master. If the SEN bit of SSPCON2 is
set, the slave hardware will always stretch the clock
after the ACK sequence. Once the slave is ready, CKP
is set by software and communication resumes.
24.5.6.2 10-bit Addressing Mode
In 10-bit Addressing mode, when the UA bit is set, the
clock is always stretched. This is the only time the SCL
is stretched without CKP being cleared. SCL is
released immediately after a write to SSPADD.
24.5.6.3 Byte NACKing
When the AHEN bit of SSPCON3 is set; CKP is
cleared by hardware after the 8th falling edge of SCL
for a received matching address byte. When the
DHEN bit of SSPCON3 is set; CKP is cleared after the
8th falling edge of SCL for received data.
Stretching after the 8th falling edge of SCL allows the
slave to look at the received address or data and
decide if it wants to ACK the received data.
24.5.7 CLOCK SYNCHRONIZATION AND
THE CKP BIT
Any time the CKP bit is cleared, the module will wait
for the SCL line to go low and then hold it. However,
clearing the CKP bit will not assert the SCL output low
until the SCL output is already sampled low. There-
fore, the CKP bit will not assert the SCL line until an
external I2C master device has already asserted the
SCL line. The SCL output will remain low until the CKP
bit is set and all other devices on the I2C bus have
released SCL. This ensures that a write to the CKP bit
will not violate the minimum high time requirement for
SCL (see Figure 24-22).
FIGURE 24-23: CLOCK SYNCHRONIZATION TIMING
Note 1: The BF bit has no effect on whether the
clock will be stretched or not. This is differ-
ent than previous versions of the module
that would not stretch the clock, clear
CKP, if SSPBUF was read before the 9th
falling edge of SCL.
2: Previous versions of the module did not
stretch the clock for a transmission if
SSPBUF was loaded before the 9th falling
edge of SCL. It is now always cleared for
read requests.
Note: Previous versions of the module did not
stretch the clock if the second address byte
did not match.
SDA
SCL
DX ‚1DX
WR
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
SSPCON1
CKP
Master device
releases clock
Master device
asserts clock
2008-2011 Microchip Technology Inc. DS41364E-page 269
PIC16(L)F1934/6/7
24.5.8 GENERAL CALL ADDRESS
SUPPORT
The addressing procedure for the I2C bus is such that
the first byte after the Start condition usually deter-
mines which device will be the slave addressed by the
master device. The exception is the general call
address which can address all devices. When this
address is used, all devices should, in theory, respond
with an Acknowledge.
The general call address is a reserved address in the
I2C protocol, defined as address 0x00. When the
GCEN bit of the SSPCON2 register is set, the slave
module will automatically ACK the reception of this
address regardless of the value stored in SSPADD.
After the slave clocks in an address of all zeros with
the R/W bit clear, an interrupt is generated and slave
software can read SSPBUF and respond.
Figure 24-23 shows a general call reception
sequence.
In 10-bit Address mode, the UA bit will not be set on
the reception of the general call address. The slave
will prepare to receive the second byte as data, just as
it would in 7-bit mode.
If the AHEN bit of the SSPCON3 register is set, just as
with any other address reception, the slave hardware
will stretch the clock after the 8th falling edge of SCL.
The slave must then set its ACKDT value and release
the clock with communication progressing as it would
normally.
FIGURE 24-24: SLAVE MODE GENERAL CALL ADDRESS SEQUENCE
24.5.9 SSP MASK REGISTER
An SSP Mask (SSPMSK) register (Register 24-5) is
available in I2C Slave mode as a mask for the value
held in the SSPSR register during an address
comparison operation. A zero (‘0’) bit in the SSPMSK
register has the effect of making the corresponding bit
of the received address a “don’t care”.
This register is reset to all ‘1s upon any Reset
condition and, therefore, has no effect on standard
SSP operation until written with a mask value.
The SSP Mask register is active during:
7-bit Address mode: address compare of A<7:1>.
10-bit Address mode: address compare of A<7:0>
only. The SSP mask has no effect during the
reception of the first (high) byte of the address.
SDA
SCL
S
SSPIF
BF (SSPSTAT<0>)
Cleared by software
SSPBUF is read
R/W = 0
ACK
General Call Address
Address is compared to General Call Address
Receiving Data ACK
123456789123456789
D7 D6 D5 D4 D3 D2 D1 D0
after ACK, set interrupt
GCEN (SSPCON2<7>)
’1’
PIC16(L)F1934/6/7
DS41364E-page 270 2008-2011 Microchip Technology Inc.
24.6 I2C Master Mode
Master mode is enabled by setting and clearing the
appropriate SSPM bits in the SSPCON1 register and
by setting the SSPEN bit. In Master mode, the SDA and
SCK pins must be configured as inputs. The MSSP
peripheral hardware will override the output driver TRIS
controls when necessary to drive the pins low.
Master mode of operation is supported by interrupt
generation on the detection of the Start and Stop con-
ditions. The Stop (P) and Start (S) bits are cleared from
a Reset or when the MSSP module is disabled. Control
of the I2C bus may be taken when the P bit is set, or the
bus is Idle.
In Firmware Controlled Master mode, user code
conducts all I2C bus operations based on Start and
Stop bit condition detection. Start and Stop condition
detection is the only active circuitry in this mode. All
other communication is done by the user software
directly manipulating the SDA and SCL lines.
The following events will cause the SSP Interrupt Flag
bit, SSPIF, to be set (SSP interrupt, if enabled):
Start condition detected
Stop condition detected
Data transfer byte transmitted/received
Acknowledge transmitted/received
Repeated Start generated
24.6.1 I2C MASTER MODE OPERATION
The master device generates all of the serial clock
pulses and the Start and Stop conditions. A transfer is
ended with a Stop condition or with a Repeated Start
condition. Since the Repeated Start condition is also
the beginning of the next serial transfer, the I2C bus will
not be released.
In Master Transmitter mode, serial data is output
through SDA, while SCL outputs the serial clock. The
first byte transmitted contains the slave address of the
receiving device (7 bits) and the Read/Write (R/W) bit.
In this case, the R/W bit will be logic ‘0’. Serial data is
transmitted 8 bits at a time. After each byte is transmit-
ted, an Acknowledge bit is received. Start and Stop
conditions are output to indicate the beginning and the
end of a serial transfer.
In Master Receive mode, the first byte transmitted con-
tains the slave address of the transmitting device
(7 bits) and the R/W bit. In this case, the R/W bit will be
logic ‘1’. Thus, the first byte transmitted is a 7-bit slave
address followed by a ‘1’ to indicate the receive bit.
Serial data is received via SDA, while SCL outputs the
serial clock. Serial data is received 8 bits at a time. After
each byte is received, an Acknowledge bit is transmit-
ted. Start and Stop conditions indicate the beginning
and end of transmission.
A Baud Rate Generator is used to set the clock fre-
quency output on SCL. See Section 24.7 “Bau d Rate
Generator” for more detail.
Note 1: The MSSP module, when configured in
I2C Master mode, does not allow queue-
ing of events. For instance, the user is not
allowed to initiate a Start condition and
immediately write the SSPBUF register to
initiate transmission before the Start con-
dition is complete. In this case, the
SSPBUF will not be written to and the
WCOL bit will be set, indicating that a
write to the SSPBUF did not occur
2: When in Master mode, Start/Stop detec-
tion is masked and an interrupt is gener-
ated when the SEN/PEN bit is cleared and
the generation is complete.
2008-2011 Microchip Technology Inc. DS41364E-page 271
PIC16(L)F1934/6/7
24.6.2 CLOCK ARBITRATION
Clock arbitration occurs when the master, during any
receive, transmit or Repeated Start/Stop condition,
releases the SCL pin (SCL allowed to float high). When
the SCL pin is allowed to float high, the Baud Rate Gen-
erator (BRG) is suspended from counting until the SCL
pin is actually sampled high. When the SCL pin is sam-
pled high, the Baud Rate Generator is reloaded with
the contents of SSPADD<7:0> and begins counting.
This ensures that the SCL high time will always be at
least one BRG rollover count in the event that the clock
is held low by an external device (Figure 24-25).
FIGURE 24-25: BAUD RATE GENERATOR TIMING WITH CLOCK ARBITRATION
24.6.3 WCOL STATUS FLAG
If the user writes the SSPBUF when a Start, Restart,
Stop, Receive or Transmit sequence is in progress, the
WCOL is set and the contents of the buffer are
unchanged (the write does not occur). Any time the
WCOL bit is set it indicates that an action on SSPBUF
was attempted while the module was not Idle.
SDA
SCL
SCL deasserted but slave holds
DX ‚1DX
BRG
SCL is sampled high, reload takes
place and BRG starts its count
03h 02h 01h 00h (hold off) 03h 02h
Reload
BRG
Value
SCL low (clock arbitration)
SCL allowed to transition high
BRG decrements on
Q2 and Q4 cycles
Note: Because queueing of events is not
allowed, writing to the lower 5 bits of
SSPCON2 is disabled until the Start
condition is complete.
PIC16(L)F1934/6/7
DS41364E-page 272 2008-2011 Microchip Technology Inc.
24.6.4 I2C MASTER MODE START
CONDITION TIMING
To initiate a Start condition, the user sets the Start
Enable bit, SEN bit of the SSPCON2 register. If the
SDA and SCL pins are sampled high, the Baud Rate
Generator is reloaded with the contents of
SSPADD<7:0> and starts its count. If SCL and SDA
are both sampled high when the Baud Rate Generator
times out (TBRG), the SDA pin is driven low. The action
of the SDA being driven low while SCL is high is the
Start condition and causes the S bit of the SSPSTAT1
register to be set. Following this, the Baud Rate Gen-
erator is reloaded with the contents of SSPADD<7:0>
and resumes its count. When the Baud Rate Genera-
tor times out (TBRG), the SEN bit of the SSPCON2 reg-
ister will be automatically cleared by hardware; the
Baud Rate Generator is suspended, leaving the SDA
line held low and the Start condition is complete.
FIGURE 24-26: FIRST START BIT TIMING
Note 1: If at the beginning of the Start condition,
the SDA and SCL pins are already sam-
pled low, or if during the Start condition,
the SCL line is sampled low before the
SDA line is driven low, a bus collision
occurs, the Bus Collision Interrupt Flag,
BCLIF, is set, the Start condition is
aborted and the I2C module is reset into
its Idle state.
2: The Philips I2C specification states that a
bus collision cannot occur on a Start.
SDA
SCL
S
TBRG
1st bit 2nd bit
TBRG
SDA = 1, At completion of Start bit,
SCL = 1
Write to SSPBUF occurs here
TBRG
hardware clears SEN bit
TBRG
Write to SEN bit occurs here Set S bit (SSPSTAT<3>)
and sets SSPIF bit
2008-2011 Microchip Technology Inc. DS41364E-page 273
PIC16(L)F1934/6/7
24.6.5 I2C MASTER MODE REPEATED
START CONDITION TIMING
A Repeated Start condition occurs when the RSEN bit
of the SSPCON2 register is programmed high and the
Master state machine is no longer active. When the
RSEN bit is set, the SCL pin is asserted low. When the
SCL pin is sampled low, the Baud Rate Generator is
loaded and begins counting. The SDA pin is released
(brought high) for one Baud Rate Generator count
(TBRG). When the Baud Rate Generator times out, if
SDA is sampled high, the SCL pin will be deasserted
(brought high). When SCL is sampled high, the Baud
Rate Generator is reloaded and begins counting. SDA
and SCL must be sampled high for one TBRG. This
action is then followed by assertion of the SDA pin
(SDA = 0) for one TBRG while SCL is high. SCL is
asserted low. Following this, the RSEN bit of the
SSPCON2 register will be automatically cleared and
the Baud Rate Generator will not be reloaded, leaving
the SDA pin held low. As soon as a Start condition is
detected on the SDA and SCL pins, the S bit of the
SSPSTAT register will be set. The SSPIF bit will not be
set until the Baud Rate Generator has timed out.
FIGURE 24-27: REPEAT START CONDITION WAVEFORM
Note 1: If RSEN is programmed while any other
event is in progress, it will not take effect.
2: A bus collision during the Repeated Start
condition occurs if:
SDA is sampled low when SCL
goes from low-to-high.
SCL goes low before SDA is
asserted low. This may indicate
that another master is attempting to
transmit a data ‘1’.
SDA
SCL
Repeated Start
Write to SSPCON2
Write to SSPBUF occurs here
At completion of Start bit,
hardware clears RSEN bit
1st bit
S bit set by hardware
TBRG
TBRG
SDA = 1,SDA = 1,
SCL (no change) SCL = 1
occurs here
TBRG TBRG TBRG
and sets SSPIF
Sr
PIC16(L)F1934/6/7
DS41364E-page 274 2008-2011 Microchip Technology Inc.
24.6.6 I2C MASTER MODE
TRANSMISSION
Transmission of a data byte, a 7-bit address or the
other half of a 10-bit address is accomplished by simply
writing a value to the SSPBUF register. This action will
set the Buffer Full (BF) flag bit, and allow the Baud Rate
Generator to begin counting and start the next trans-
mission. Each bit of address/data will be shifted out
onto the SDA pin after the falling edge of SCL is
asserted. SCL is held low for one Baud Rate Generator
rollover count (TBRG). Data should be valid before SCL
is released high. When the SCL pin is released high, it
is held that way for TBRG. The data on the SDA pin
must remain stable for that duration and some hold
time after the next falling edge of SCL. After the eighth
bit is shifted out (the falling edge of the eighth clock),
the BF flag is cleared and the master releases SDA.
This allows the slave device being addressed to
respond with an ACK bit during the ninth bit time if an
address match occurred, or if data was received prop-
erly. The status of ACK is written into the ACKSTAT bit
on the rising edge of the ninth clock. If the master
receives an Acknowledge, the Acknowledge Status bit,
ACKSTAT, is cleared. If not, the bit is set. After the ninth
clock, the SSPIF bit is set and the master clock (Baud
Rate Generator) is suspended until the next data byte
is loaded into the SSPBUF, leaving SCL low and SDA
unchanged (Figure 24-27).
After the write to the SSPBUF, each bit of the address
will be shifted out on the falling edge of SCL until all
seven address bits and the R/W bit are completed. On
the falling edge of the eighth clock, the master will
release the SDA pin, allowing the slave to respond with
an Acknowledge. On the falling edge of the ninth clock,
the master will sample the SDA pin to see if the address
was recognized by a slave. The status of the ACK bit is
loaded into the ACKSTAT Status bit of the SSPCON2
register. Following the falling edge of the ninth clock
transmission of the address, the SSPIF is set, the BF
flag is cleared and the Baud Rate Generator is turned
off until another write to the SSPBUF takes place, hold-
ing SCL low and allowing SDA to float.
24.6.6.1 BF Status Flag
In Transmit mode, the BF bit of the SSPSTAT register
is set when the CPU writes to SSPBUF and is cleared
when all 8 bits are shifted out.
24.6.6.2 WCOL Status Flag
If the user writes the SSPBUF when a transmit is
already in progress (i.e., SSPSR is still shifting out a
data byte), the WCOL is set and the contents of the buf-
fer are unchanged (the write does not occur).
WCOL must be cleared by software before the next
transmission.
24.6.6.3 ACKSTAT Status Flag
In Transmit mode, the ACKSTAT bit of the SSPCON2
register is cleared when the slave has sent an Acknowl-
edge (ACK =0) and is set when the slave does not
Acknowledge (ACK =1). A slave sends an Acknowl-
edge when it has recognized its address (including a
general call), or when the slave has properly received
its data.
24.6.6.4 Typical transmit sequence:
1. The user generates a Start condition by setting
the SEN bit of the SSPCON2 register.
2. SSPIF is set by hardware on completion of the
Start.
3. SSPIF is cleared by software.
4. The MSSP module will wait the required start
time before any other operation takes place.
5. The user loads the SSPBUF with the slave
address to transmit.
6. Address is shifted out the SDA pin until all 8 bits
are transmitted. Transmission begins as soon
as SSPBUF is written to.
7. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
ACKSTAT bit of the SSPCON2 register.
8. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
9. The user loads the SSPBUF with eight bits of
data.
10. Data is shifted out the SDA pin until all 8 bits are
transmitted.
11. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
ACKSTAT bit of the SSPCON2 register.
12. Steps 8-11 are repeated for all transmitted data
bytes.
13. The user generates a Stop or Restart condition
by setting the PEN or RSEN bits of the
SSPCON2 register. Interrupt is generated once
the Stop/Restart condition is complete.
2008-2011 Microchip Technology Inc. DS41364E-page 275
PIC16(L)F1934/6/7
FIGURE 24-28 : I2C MASTER MODE WAVEFORM (RECEPTION, 7-BIT ADDRESS)
P
9
87
6
5
D0
D1
D2
D3D4
D5
D6D7
S
A7 A6 A5 A4 A3 A2 A1
SDA
SCL 12345678912345678 9 1234
Bus master
terminates
transfer
ACK
Receiving Data from Slave
Receiving Data from Slave
D0
D1
D2
D3D4
D5
D6D7
ACK
R/W
Transmit Address to Slave
SSPIF
BF
ACK is not sent
Write to SSPCON2<0> (SEN = 1),
Write to SSPBUF occurs here, ACK from Slave
Master configured as a receiver
by programming SSPCON2<3> (RCEN = 1)
PEN bit = 1
written here
Data shifted in on falling edge of CLK
Cleared by software
start XMIT
SEN = 0
SSPOV
SDA = 0, SCL = 1
while CPU
(SSPSTAT<0>)
ACK
Cleared by software
Cleared by software
Set SSPIF interrupt
at end of receive
Set P bit
(SSPSTAT<4>)
and SSPIF
Cleared in
software
ACK from Master
Set SSPIF at end
Set SSPIF interrupt
at end of Acknowledge
sequence
Set SSPIF interrupt
at end of Acknow-
ledge sequence
of receive
Set ACKEN, start Acknowledge sequence
SSPOV is set because
SSPBUF is still full
SDA = ACKDT = 1
RCEN cleared
automatically
RCEN = 1, start
next receive
Write to SSPCON2<4>
to start Acknowledge sequence
SDA = ACKDT (SSPCON2<5>) = 0
RCEN cleared
automatically
responds to SSPIF
ACKEN
begin Start condition
Cleared by software
SDA = ACKDT = 0
Last bit is shifted into SSPSR and
contents are unloaded into SSPBUF
RCEN
Master configured as a receiver
by programming SSPCON2<3> (RCEN = 1)
RCEN cleared
automatically
ACK from Master
SDA = ACKDT = 0 RCEN cleared
automatically
PIC16(L)F1934/6/7
DS41364E-page 276 2008-2011 Microchip Technology Inc.
24.6.7 I2C MASTER MODE RECEPTION
Master mode reception is enabled by programming the
Receive Enable bit, RCEN bit of the SSPCON2
register.
The Baud Rate Generator begins counting and on each
rollover, the state of the SCL pin changes
(high-to-low/low-to-high) and data is shifted into the
SSPSR. After the falling edge of the eighth clock, the
receive enable flag is automatically cleared, the con-
tents of the SSPSR are loaded into the SSPBUF, the
BF flag bit is set, the SSPIF flag bit is set and the Baud
Rate Generator is suspended from counting, holding
SCL low. The MSSP is now in Idle state awaiting the
next command. When the buffer is read by the CPU,
the BF flag bit is automatically cleared. The user can
then send an Acknowledge bit at the end of reception
by setting the Acknowledge Sequence Enable, ACKEN
bit of the SSPCON2 register.
24.6.7.1 BF Status Flag
In receive operation, the BF bit is set when an address
or data byte is loaded into SSPBUF from SSPSR. It is
cleared when the SSPBUF register is read.
24.6.7.2 SSPOV Status Flag
In receive operation, the SSPOV bit is set when 8 bits
are received into the SSPSR and the BF flag bit is
already set from a previous reception.
24.6.7.3 WCOL Status Flag
If the user writes the SSPBUF when a receive is
already in progress (i.e., SSPSR is still shifting in a data
byte), the WCOL bit is set and the contents of the buffer
are unchanged (the write does not occur).
24.6.7.4 Typical Receive Sequence:
1. The user generates a Start condition by setting
the SEN bit of the SSPCON2 register.
2. SSPIF is set by hardware on completion of the
Start.
3. SSPIF is cleared by software.
4. User writes SSPBUF with the slave address to
transmit and the R/W bit set.
5. Address is shifted out the SDA pin until all 8 bits
are transmitted. Transmission begins as soon
as SSPBUF is written to.
6. The MSSP module shifts in the ACK bit from the
slave device and writes its value into the
ACKSTAT bit of the SSPCON2 register.
7. The MSSP module generates an interrupt at the
end of the ninth clock cycle by setting the SSPIF
bit.
8. User sets the RCEN bit of the SSPCON2 register
and the Master clocks in a byte from the slave.
9. After the 8th falling edge of SCL, SSPIF and BF
are set.
10. Master clears SSPIF and reads the received
byte from SSPBUF, clears BF.
11. Master sets ACK value sent to slave in ACKDT
bit of the SSPCON2 register and initiates the
ACK by setting the ACKEN bit.
12. Masters ACK is clocked out to the Slave and
SSPIF is set.
13. User clears SSPIF.
14. Steps 8-13 are repeated for each received byte
from the slave.
15. Master sends a not ACK or Stop to end
communication.
Note: The MSSP module must be in an Idle
state before the RCEN bit is set or the
RCEN bit will be disregarded.
2008-2011 Microchip Technology Inc. DS41364E-page 277
PIC16(L)F1934/6/7
FIGURE 24-29 : I2C MASTER MODE WAVEFORM (RECEPTION, 7-BIT ADDRESS)
P
9
87
6
5
D0
D1
D2
D3D4
D5
D6D7
S
A7 A6 A5 A4 A3 A2 A1
SDA
SCL 12345678912345678 9 1234
Bus master
terminates
transfer
ACK
Receiving Data from Slave
Receiving Data from Slave
D0
D1
D2
D3D4
D5
D6D7
ACK
R/W
Transmit Address to Slave
SSPIF
BF
ACK is not sent
Write to SSPCON2<0> (SEN = 1),
Write to SSPBUF occurs here, ACK from Slave
Master configured as a receiver
by programming SSPCON2<3> (RCEN = 1)
PEN bit = 1
written here
Data shifted in on falling edge of CLK
Cleared by software
start XMIT
SEN = 0
SSPOV
SDA = 0, SCL = 1
while CPU
(SSPSTAT<0>)
ACK
Cleared by software
Cleared by software
Set SSPIF interrupt
at end of receive
Set P bit
(SSPSTAT<4>)
and SSPIF
Cleared in
software
ACK from Master
Set SSPIF at end
Set SSPIF interrupt
at end of Acknowledge
sequence
Set SSPIF interrupt
at end of Acknow-
ledge sequence
of receive
Set ACKEN, start Acknowledge sequence
SSPOV is set because
SSPBUF is still full
SDA = ACKDT = 1
RCEN cleared
automatically
RCEN = 1, start
next receive
Write to SSPCON2<4>
to start Acknowledge sequence
SDA = ACKDT (SSPCON2<5>) = 0
RCEN cleared
automatically
responds to SSPIF
ACKEN
begin Start condition
Cleared by software
SDA = ACKDT = 0
Last bit is shifted into SSPSR and
contents are unloaded into SSPBUF
RCEN
Master configured as a receiver
by programming SSPCON2<3> (RCEN = 1)
RCEN cleared
automatically
ACK from Master
SDA = ACKDT = 0 RCEN cleared
automatically
PIC16(L)F1934/6/7
DS41364E-page 278 2008-2011 Microchip Technology Inc.
24.6.8 ACKNOWLEDGE SEQUENCE
TIMING
An Acknowledge sequence is enabled by setting the
Acknowledge Sequence Enable bit, ACKEN bit of the
SSPCON2 register. When this bit is set, the SCL pin is
pulled low and the contents of the Acknowledge data bit
are presented on the SDA pin. If the user wishes to gen-
erate an Acknowledge, then the ACKDT bit should be
cleared. If not, the user should set the ACKDT bit before
starting an Acknowledge sequence. The Baud Rate
Generator then counts for one rollover period (TBRG)
and the SCL pin is deasserted (pulled high). When the
SCL pin is sampled high (clock arbitration), the Baud
Rate Generator counts for TBRG. The SCL pin is then
pulled low. Following this, the ACKEN bit is automatically
cleared, the Baud Rate Generator is turned off and the
MSSP module then goes into Idle mode (Figure 24-29).
24.6.8.1 WCOL Status Flag
If the user writes the SSPBUF when an Acknowledge
sequence is in progress, then WCOL is set and the
contents of the buffer are unchanged (the write does
not occur).
24.6.9 STOP CONDITION TIMING
A Stop bit is asserted on the SDA pin at the end of a
receive/transmit by setting the Stop Sequence Enable
bit, PEN bit of the SSPCON2 register. At the end of a
receive/transmit, the SCL line is held low after the
falling edge of the ninth clock. When the PEN bit is set,
the master will assert the SDA line low. When the SDA
line is sampled low, the Baud Rate Generator is
reloaded and counts down to ‘0’. When the Baud Rate
Generator times out, the SCL pin will be brought high
and one TBRG (Baud Rate Generator rollover count)
later, the SDA pin will be deasserted. When the SDA
pin is sampled high while SCL is high, the P bit of the
SSPSTAT register is set. A TBRG later, the PEN bit is
cleared and the SSPIF bit is set (Figure 24-30).
24.6.9.1 WCOL Status Flag
If the user writes the SSPBUF when a Stop sequence
is in progress, then the WCOL bit is set and the
contents of the buffer are unchanged (the write does
not occur).
FIGURE 24-30: ACKNOWLEDGE SEQUEN CE WAVEFORM
FIGURE 24-31: STOP CONDITION RECEIVE OR TRANSMIT MODE
Note: TBRG = one Baud Rate Generator period.
SDA
SCL
SSPIF set at
Acknowledge sequence starts here,
write to SSPCON2 ACKEN automatically cleared
Cleared in
TBRG TBRG
the end of receive
8
ACKEN = 1, ACKDT = 0
D0
9
SSPIF
software SSPIF set at the end
of Acknowledge sequence
Cleared in
software
ACK
SCL
SDA
SDA asserted low before rising edge of clock
Write to SSPCON2,
set PEN
Falling edge of
SCL = 1 for TBRG, followed by SDA = 1 for TBRG
9th clock
SCL brought high after TBRG
Note: TBRG = one Baud Rate Generator period.
TBRG TBRG
after SDA sampled high. P bit (SSPSTAT<4>) is set.
TBRG
to setup Stop condition
ACK
P
TBRG
PEN bit (SSPCON2<2>) is cleared by
hardware and the SSPIF bit is set
2008-2011 Microchip Technology Inc. DS41364E-page 279
PIC16(L)F1934/6/7
24.6.10 SLEEP OPERATION
While in Sleep mode, the I2C slave module can receive
addresses or data and when an address match or
complete byte transfer occurs, wake the processor
from Sleep (if the MSSP interrupt is enabled).
24.6.11 EFFECTS OF A RESET
A Reset disables the MSSP module and terminates the
current transfer.
24.6.12 MULTI-MASTER MODE
In Multi-Master mode, the interrupt generation on the
detection of the Start and Stop conditions allows the
determination of when the bus is free. The Stop (P) and
Start (S) bits are cleared from a Reset or when the
MSSP module is disabled. Control of the I2C bus may
be taken when the P bit of the SSPSTAT register is set,
or the bus is Idle, with both the S and P bits clear. When
the bus is busy, enabling the SSP interrupt will gener-
ate the interrupt when the Stop condition occurs.
In multi-master operation, the SDA line must be
monitored for arbitration to see if the signal level is the
expected output level. This check is performed by
hardware with the result placed in the BCLIF bit.
The states where arbitration can be lost are:
Address Transfer
Data Transfer
A Start Condition
A Repeated Start Condition
An Acknowledge Condition
24.6.13 MULTI -MASTER COMMUNICATION,
BUS COLLISION AND BUS
ARBITRATION
Multi-Master mode support is achieved by bus arbitra-
tion. When the master outputs address/data bits onto
the SDA pin, arbitration takes place when the master
outputs a ‘1on SDA, by letting SDA float high and
another master asserts a ‘0’. When the SCL pin floats
high, data should be stable. If the expected data on
SDA is a ‘1’ and the data sampled on the SDA pin is ‘0’,
then a bus collision has taken place. The master will set
the Bus Collision Interrupt Flag, BCLIF, and reset the
I2C port to its Idle state (Figure 24-31).
If a transmit was in progress when the bus collision
occurred, the transmission is halted, the BF flag is
cleared, the SDA and SCL lines are deasserted and the
SSPBUF can be written to. When the user services the
bus collision Interrupt Service Routine and if the I2C
bus is free, the user can resume communication by
asserting a Start condition.
If a Start, Repeated Start, Stop or Acknowledge condi-
tion was in progress when the bus collision occurred, the
condition is aborted, the SDA and SCL lines are deas-
serted and the respective control bits in the SSPCON2
register are cleared. When the user services the bus col-
lision Interrupt Service Routine and if the I2C bus is free,
the user can resume communication by asserting a Start
condition.
The master will continue to monitor the SDA and SCL
pins. If a Stop condition occurs, the SSPIF bit will be set.
A write to the SSPBUF will start the transmission of
data at the first data bit, regardless of where the
transmitter left off when the bus collision occurred.
In Multi-Master mode, the interrupt generation on the
detection of Start and Stop conditions allows the deter-
mination of when the bus is free. Control of the I2C bus
can be taken when the P bit is set in the SSPSTAT
register, or the bus is Idle and the S and P bits are
cleared.
FIGURE 24-32: BUS COLLISION TIMING FOR TRANSMIT AND ACKNOWLEDGE
SDA
SCL
BCLIF
SDA released
SDA line pulled low
by another source
Sample SDA. While SCL is high,
data does not match what is driven
Bus collision has occurred.
Set bus collision
interrupt (BCLIF)
by the master.
by master
Data changes
while SCL = 0
PIC16(L)F1934/6/7
DS41364E-page 280 2008-2011 Microchip Technology Inc.
24.6.13.1 Bus Collision During a Start
Condition
During a Start condition, a bus collision occurs if:
a) SDA or SCL are sampled low at the beginning of
the Start condition (Figure 24-32).
b) SCL is sampled low before SDA is asserted low
(Figure 24-33).
During a Start condition, both the SDA and the SCL
pins are monitored.
If the SDA pin is already low, or the SCL pin is already
low, then all of the following occur:
the Start condition is aborted,
the BCLIF flag is set and
the MSSP module is reset to its Idle state
(Figure 24-32).
The Start condition begins with the SDA and SCL pins
deasserted. When the SDA pin is sampled high, the
Baud Rate Generator is loaded and counts down. If the
SCL pin is sampled low while SDA is high, a bus colli-
sion occurs because it is assumed that another master
is attempting to drive a data ‘1’ during the Start
condition.
If the SDA pin is sampled low during this count, the
BRG is reset and the SDA line is asserted early
(Figure 24-34). If, however, a ‘1’ is sampled on the SDA
pin, the SDA pin is asserted low at the end of the BRG
count. The Baud Rate Generator is then reloaded and
counts down to zero; if the SCL pin is sampled as0
during this time, a bus collision does not occur. At the
end of the BRG count, the SCL pin is asserted low.
FIGURE 24-33: BUS COLLISION DURING START CONDITION (SDA ONLY)
Note: The reason that bus collision is not a fac-
tor during a Start condition is that no two
bus masters can assert a Start condition
at the exact same time. Therefore, one
master will always assert SDA before the
other. This condition does not cause a bus
collision because the two masters must be
allowed to arbitrate the first address fol-
lowing the Start condition. If the address is
the same, arbitration must be allowed to
continue into the data portion, Repeated
Start or Stop conditions.
SDA
SCL
SEN
SDA sampled low before
SDA goes low before the SEN bit is set.
S bit and SSPIF set because
SSP module reset into Idle state.
SEN cleared automatically because of bus collision.
S bit and SSPIF set because
Set SEN, enable Start
condition if SDA = 1, SCL = 1
SDA = 0, SCL = 1.
BCLIF
S
SSPIF
SDA = 0, SCL = 1.
SSPIF and BCLIF are
cleared by software
SSPIF and BCLIF are
cleared by software
Set BCLIF,
Start condition. Set BCLIF.
2008-2011 Microchip Technology Inc. DS41364E-page 281
PIC16(L)F1934/6/7
FIGURE 24-34: BUS COLLISION DURING START CONDITION (SCL = 0)
FIGURE 24-35: BRG RESET DUE TO SDA ARBITRATION DURING START CONDITION
SDA
SCL
SEN bus collision occurs. Set BCLIF.
SCL = 0 before SDA = 0,
Set SEN, enable Start
sequence if SDA = 1, SCL = 1
TBRG TBRG
SDA = 0, SCL = 1
BCLIF
S
SSPIF
Interrupt cleared
by software
bus collision occurs. Set BCLIF.
SCL = 0 before BRG time-out,
0’’0
00
SDA
SCL
SEN
Set S
Less than TBRG TBRG
SDA = 0, SCL = 1
BCLIF
S
SSPIF
S
Interrupts cleared
by software
set SSPIF
SDA = 0, SCL = 1,
SCL pulled low after BRG
time-out
Set SSPIF
0
SDA pulled low by other master.
Reset BRG and assert SDA.
Set SEN, enable Start
sequence if SDA = 1, SCL = 1
PIC16(L)F1934/6/7
DS41364E-page 282 2008-2011 Microchip Technology Inc.
24.6.13.2 Bus Collision During a Repeated
Start Condition
During a Repeated Start condition, a bus collision
occurs if:
a) A low level is sampled on SDA when SCL goes
from low level to high level.
b) SCL goes low before SDA is asserted low,
indicating that another master is attempting to
transmit a data ‘1’.
When the user releases SDA and the pin is allowed to
float high, the BRG is loaded with SSPADD and counts
down to zero. The SCL pin is then deasserted and
when sampled high, the SDA pin is sampled.
If SDA is low, a bus collision has occurred (i.e., another
master is attempting to transmit a data ‘0’, Figure 24-35).
If SDA is sampled high, the BRG is reloaded and begins
counting. If SDA goes from high-to-low before the BRG
times out, no bus collision occurs because no two
masters can assert SDA at exactly the same time.
If SCL goes from high-to-low before the BRG times out
and SDA has not already been asserted, a bus collision
occurs. In this case, another master is attempting to
transmit a data ‘1’ during the Repeated Start condition,
see Figure 24-36.
If, at the end of the BRG time-out, both SCL and SDA
are still high, the SDA pin is driven low and the BRG is
reloaded and begins counting. At the end of the count,
regardless of the status of the SCL pin, the SCL pin is
driven low and the Repeated Start condition is
complete.
FIGURE 24-36: BUS COLLISION DURING A REPEATED START CONDITION (CASE 1)
FIGURE 24-37: BUS COLLISION DURING REPEATED START CONDITION (CASE 2)
SDA
SCL
RSEN
BCLIF
S
SSPIF
Sample SDA when SCL goes high.
If SDA = 0, set BCLIF and release SDA and SCL.
Cleared by software
0
0
SDA
SCL
BCLIF
RSEN
S
SSPIF
Interrupt cleared
by software
SCL goes low before SDA,
set BCLIF. Release SDA and SCL.
TBRG TBRG
0
2008-2011 Microchip Technology Inc. DS41364E-page 283
PIC16(L)F1934/6/7
24.6.13.3 Bus Collision During a Stop
Condition
Bus collision occurs during a Stop condition if:
a) After the SDA pin has been deasserted and
allowed to float high, SDA is sampled low after
the BRG has timed out.
b) After the SCL pin is deasserted, SCL is sampled
low before SDA goes high.
The Stop condition begins with SDA asserted low.
When SDA is sampled low, the SCL pin is allowed to
float. When the pin is sampled high (clock arbitration),
the Baud Rate Generator is loaded with SSPADD and
counts down to 0. After the BRG times out, SDA is
sampled. If SDA is sampled low, a bus collision has
occurred. This is due to another master attempting to
drive a data0’ (Figure 24-37). If the SCL pin is sampled
low before SDA is allowed to float high, a bus collision
occurs. This is another case of another master
attempting to drive a data ‘0’ (Figure 24-38).
FIGURE 24-38: BUS COLLISION DURING A STOP CONDITION (CASE 1)
FIGURE 24-39: BUS COLLISION DURING A STOP CONDITION (CASE 2)
SDA
SCL
BCLIF
PEN
P
SSPIF
TBRG TBRG TBRG
SDA asserted low
SDA sampled
low after TBRG,
set BCLIF
0
0
SDA
SCL
BCLIF
PEN
P
SSPIF
TBRG TBRG TBRG
Assert SDA SCL goes low before SDA goes high,
set BCLIF
0
0
PIC16(L)F1934/6/7
DS41364E-page 284 2008-2011 Microchip Technology Inc.
TABLE 24-3: SUMMARY OF REGISTERS ASSOCIATED WITH I2C™ OPERATION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Reset
Values on
Page:
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIE2 OSFIE C2IE C1IE EEIE BCLIE CCP2IE(1) 100
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
PIR2 OSFIF C2IF C1IF EEIF BCLIF CCP2IF(1) 103
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
SSPADD ADD<7:0> 290
SSPBUF MSSP Receive Buffer/Transmit Register 243*
SSPCON1 WCOL SSPOV SSPEN CKP SSPM<3:0> 287
SSPCON2 GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN 288
SSPCON3 ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN 289
SSPMSK MSK<7:0> 290
SSPSTAT SMP CKE D/A PSR/WUA BF 286
Legend: — = unimplemented location, read as 0’. Shaded cells are not used by the MSSP module in I2C™ mode.
* Page provides register information.
Note 1: PIC16F1934 only.
2008-2011 Microchip Technology Inc. DS41364E-page 285
PIC16(L)F1934/6/7
24.7 Baud Rate Generator
The MSSP module has a Baud Rate Generator avail-
able for clock generation in both I2C and SPI Master
modes. The Baud Rate Generator (BRG) reload value
is placed in the SSPADD register (Register 24-6).
When a write occurs to SSPBUF, the Baud Rate Gen-
erator will automatically begin counting down.
Once the given operation is complete, the internal clock
will automatically stop counting and the clock pin will
remain in its last state.
An internal signal “Reload” in Figure 24-39 triggers the
value from SSPADD to be loaded into the BRG counter.
This occurs twice for each oscillation of the module
clock line. The logic dictating when the reload signal is
asserted depends on the mode the MSSP is being
operated in.
Table 24-4 demonstrates clock rates based on
instruction cycles and the BRG value loaded into
SSPADD.
EQUATION 24-1:
FIGURE 24-40: BAUD RATE GENERATOR BLOCK DIAGRAM
TABLE 24-4: MSSP CLOCK RATE W/BRG
FCLOCK FOSC
SSPxADD 1+4
-------------------------------------------------=
Note: Values of 0x00, 0x01 and 0x02 are not valid
for SSPADD when used as a Baud Rate
Generator for I2C. This is an implementation
limitation.
FOSC FCY BRG Value FCLOCK
(2 Rollovers of BRG)
32 MHz 8 MHz 13h 400 kHz(1)
32 MHz 8 MHz 19h 308 kHz
32 MHz 8 MHz 4Fh 100 kHz
16 MHz 4 MHz 09h 400 kHz(1)
16 MHz 4 MHz 0Ch 308 kHz
16 MHz 4 MHz 27h 100 kHz
4 MHz 1 MHz 09h 100 kHz
Note 1: The I2C interface does not conform to the 400 kHz I2C specification (which applies to rates greater than
100 kHz) in all details, but may be used with care where higher rates are required by the application.
SSPM<3:0>
BRG Down Counter
SSPCLK FOSC/2
SSPADD<7:0>
SSPM<3:0>
SCL
Reload
Control
Reload
PIC16(L)F1934/6/7
DS41364E-page 286 2008-2011 Microchip Technology Inc.
REGISTER 24-1: SSPSTAT: SSP STATUS REGISTER
R/W-0/0 R/W-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0 R-0/0
SMP CKE D/A PSR/WUA BF
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 SMP: SPI Data Input Sample bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode
In I2 C Master or Slave mode:
1 = Slew rate control disabled for standard speed mode (100 kHz and 1 MHz)
0 = Slew rate control enabled for high speed mode (400 kHz)
bit 6 CKE: SPI Clock Edge Select bit (SPI mode only)
In SPI Master or Slave mode:
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
In I2 Cmode only:
1 = Enable input logic so that thresholds are compliant with SMBus specification
0 = Disable SMBus specific inputs
bit 5 D/A: Data/Address bit (I2C mode only)
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
bit 4 P: Stop bit
(I2C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.)
1 = Indicates that a Stop bit has been detected last (this bit is ‘0’ on Reset)
0 = Stop bit was not detected last
bit 3 S: Start bit
(I2C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.)
1 = Indicates that a Start bit has been detected last (this bit is ‘0’ on Reset)
0 = Start bit was not detected last
bit 2 R/W: Read/Write bit information (I2C mode only)
This bit holds the R/W bit information following the last address match. This bit is only valid from the address match
to the next Start bit, Stop bit, or not ACK bit.
In I2 C Slave mode:
1 = Read
0 = Write
In I2 C Master mode:
1 = Transmit is in progress
0 = Transmit is not in progress
OR-ing this bit with SEN, RSEN, PEN, RCEN or ACKEN will indicate if the MSSP is in Idle mode.
bit 1 UA: Update Address bit (10-bit I2C mode only)
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
bit 0 BF: Buffer Full Status bit
Receive (SPI and I2 C modes):
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Transmit (I2 C mode only):
1 = Data transmit in progress (does not include the ACK and Stop bits), SSPBUF is full
0 = Data transmit complete (does not include the ACK and Stop bits), SSPBUF is empty
2008-2011 Microchip Technology Inc. DS41364E-page 287
PIC16(L)F1934/6/7
REGISTER 24-2: SSPCON1: SSP CONTROL REGISTER 1
R/C/HS-0/0 R/C/HS-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
WCOL SSPOV SSPEN CKP SSPM<3:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared HS = Bit is set by hardware C = User cleared
bit 7 WCOL: Write Collision Detect bit
Master mode:
1 = A write to the SSPBUF register was attempted while the I2C conditions were not valid for a transmission to be started
0 = No collision
Slave mode:
1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software)
0 = No collision
bit 6 SSPOV: Receive Overflow Indicator bit(1)
In SPI mode:
1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost.
Overflow can only occur in Slave mode. In Slave mode, the user must read the SSPBUF, even if only transmitting data, to avoid
setting overflow. In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the
SSPBUF register (must be cleared in software).
0 = No overflow
In I2 C mode:
1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a “don’t care” in Transmit mode
(must be cleared in software).
0 = No overflow
bit 5 SSPEN: Synchronous Serial Port Enable bit
In both modes, when enabled, these pins must be properly configured as input or output
In SPI mode:
1 = Enables serial port and configures SCK, SDO, SDI and SS as the source of the serial port pins(2)
0 = Disables serial port and configures these pins as I/O port pins
In I2 C mode:
1 = Enables the serial port and configures the SDA and SCL pins as the source of the serial port pins(3)
0 = Disables serial port and configures these pins as I/O port pins
bit 4 CKP: Clock Polarity Select bit
In SPI mode:
1 = Idle state for clock is a high level
0 = Idle state for clock is a low level
In I2 C Slave mode:
SCL release control
1 = Enable clock
0 = Holds clock low (clock stretch). (Used to ensure data setup time.)
In I2 C Master mode:
Unused in this mode
bit 3-0 SSPM<3:0>: Synchronous Serial Port Mode Select bits
0000 = SPI Master mode, clock = FOSC/4
0001 = SPI Master mode, clock = FOSC/16
0010 = SPI Master mode, clock = FOSC/64
0011 = SPI Master mode, clock = TMR2 output/2
0100 = SPI Slave mode, clock = SCK pin, SS pin control enabled
0101 = SPI Slave mode, clock = SCK pin, SS pin control disabled, SS can be used as I/O pin
0110 = I2C Slave mode, 7-bit address
0111 = I2C Slave mode, 10-bit address
1000 = I2C Master mode, clock = FOSC / (4 * (SSPADD+1))(4)
1001 = Reserved
1010 = SPI Master mode, clock = FOSC/(4 * (SSPADD+1))(5)
1011 = I2C firmware controlled Master mode (Slave Idle)
1100 = Reserved
1101 = Reserved
1110 = I2C Slave mode, 7-bit address with Start and Stop bit interrupts enabled
1111 = I2C Slave mode, 10-bit address with Start and Stop bit interrupts enabled
Note 1: In Master mode, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register.
2: When enabled, these pins must be properly configured as input or output.
3: When enabled, the SDA and SCL pins must be configured as inputs.
4: SSPADD values of 0, 1 or 2 are not supported for I2C Mode.
5: SSPADD value of0’ is not supported. Use SSPM = 0000 instead.
PIC16(L)F1934/6/7
DS41364E-page 288 2008-2011 Microchip Technology Inc.
REGISTER 24-3: SSPCON2: SSP CONTROL REGISTER 2
R/W-0/0 R-0/0 R/W-0/0 R/S/HS-0/0 R/S/HS-0/0 R/S/HS-0/0 R/S/HS-0/0 R/W/HS-0/0
GCEN ACKSTAT ACKDT ACKEN RCEN PEN RSEN SEN
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared HC = Cleared by hardware S = User set
bit 7 GCEN: General Call Enable bit (in I2C Slave mode only)
1 = Enable interrupt when a general call address (0x00 or 00h) is received in the SSPSR
0 = General call address disabled
bit 6 ACKSTAT: Acknowledge Status bit (in I2C mode only)
1 = Acknowledge was not received
0 = Acknowledge was received
bit 5 ACKDT: Acknowledge Data bit (in I2C mode only)
In Receive mode:
Value transmitted when the user initiates an Acknowledge sequence at the end of a receive
1 = Not Acknowledge
0 = Acknowledge
bit 4 ACKEN: Acknowledge Sequence Enable bit (in I2C Master mode only)
In Master Receive mode:
1 = Initiate Acknowledge sequence on SDA and SCL pins, and transmit ACKDT data bit.
Automatically cleared by hardware.
0 = Acknowledge sequence Idle
bit 3 RCEN: Receive Enable bit (in I2C Master mode only)
1 = Enables Receive mode for I2C
0 = Receive Idle
bit 2 PEN: Stop Condition Enable bit (in I2C Master mode only)
SCKMSSP Release Control:
1 = Initiate Stop condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Stop condition Idle
bit 1 RSEN: Repeated Start Condition Enabled bit (in I2C Master mode only)
1 = Initiate Repeated Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Repeated Start condition Idle
bit 0 SEN: Start Condition Enabled bit (in I2C Master mode only)
In Master mode:
1 = Initiate Start condition on SDA and SCL pins. Automatically cleared by hardware.
0 = Start condition Idle
In Slave mode:
1 = Clock stretching is enabled for both slave transmit and slave receive (stretch enabled)
0 = Clock stretching is disabled
Note 1: For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I2C module is not in the Idle mode, this bit may not be
set (no spooling) and the SSPBUF may not be written (or writes to the SSPBUF are disabled).
2008-2011 Microchip Technology Inc. DS41364E-page 289
PIC16(L)F1934/6/7
REGISTER 24-4: SSPCON3: SSP CONTROL REGISTER 3
R-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ACKTIM PCIE SCIE BOEN SDAHT SBCDE AHEN DHEN
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 ACKTIM: Acknowledge Time Status bit (I2C mode only)(3)
1 = Indicates the I2C bus is in an Acknowledge sequence, set on 8TH falling edge of SCL clock
0 = Not an Acknowledge sequence, cleared on 9TH rising edge of SCL clock
bit 6 PCIE: Stop Condition Interrupt Enable bit (I2C mode only)
1 = Enable interrupt on detection of Stop condition
0 = Stop detection interrupts are disabled(2)
bit 5 SCIE: Start Condition Interrupt Enable bit (I2C mode only)
1 = Enable interrupt on detection of Start or Restart conditions
0 = Start detection interrupts are disabled(2)
bit 4 BOEN: Buffer Overwrite Enable bit
In SPI Slave mode:(1)
1 = SSPBUF updates every time that a new data byte is shifted in ignoring the BF bit
0 = If new byte is received with BF bit of the SSPSTAT register already set, SSPOV bit of the
SSPCON1 register is set, and the buffer is not updated
In I2C Master and SPI Master mode:
This bit is ignored.
In I2C Slave mode:
1 = SSPBUF is updated and ACK is generated for a received address/data byte, ignoring the state
of the SSPOV bit only if the BF bit = 0.
0 = SSPBUF is only updated when SSPOV is clear
bit 3 SDAHT: SDA Hold Time Selection bit (I2C mode only)
1 = Minimum of 300 ns hold time on SDA after the falling edge of SCL
0 = Minimum of 100 ns hold time on SDA after the falling edge of SCL
bit 2 SBCDE: Slave Mode Bus Collision Detect Enable bit (I2C Slave mode only)
If on the rising edge of SCL, SDA is sampled low when the module is outputting a high state, the BCLIF
bit of the PIR2 register is set, and bus goes Idle
1 = Enable slave bus collision interrupts
0 = Slave bus collision interrupts are disabled
bit 1 AHEN: Address Hold Enable bit (I2C Slave mode only)
1 = Following the 8th falling edge of SCL for a matching received address byte; CKP bit of the
SSPCON1 register will be cleared and the SCL will be held low.
0 = Address holding is disabled
bit 0 DHEN: Data Hold Enable bit (I2C Slave mode only)
1 = Following the 8th falling edge of SCL for a received data byte; slave hardware clears the CKP bit
of the SSPCON1 register and SCL is held low.
0 = Data holding is disabled
Note 1: For daisy-chained SPI operation; allows the user to ignore all but the last received byte. SSPOV is still set
when a new byte is received and BF = 1, but hardware continues to write the most recent byte to SSPBUF.
2: This bit has no effect in Slave modes that Start and Stop condition detection is explicitly listed as enabled.
3: The ACKTIM Status bit is only active when the AHEN bit or DHEN bit is set.
PIC16(L)F1934/6/7
DS41364E-page 290 2008-2011 Microchip Technology Inc.
REGISTER 24-5: SSPMSK: SSP MASK REGISTER
R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1 R/W-1/1
MSK<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-1 MSK<7:1>: Mask bits
1 = The received address bit n is compared to SSPADD<n> to detect I2C address match
0 = The received address bit n is not used to detect I2C address match
bit 0 MSK<0>: Mask bit for I2C Slave mode, 10-bit Address
I2C Slave mode, 10-bit address (SSPM<3:0> = 0111 or 1111):
1 = The received address bit 0 is compared to SSPADD<0> to detect I2C address match
0 = The received address bit 0 is not used to detect I2C address match
I2C Slave mode, 7-bit address, the bit is ignored
REGISTER 24-6: SSPADD: MSSP ADDRESS AND BAUD RATE REGISTER (I2C MODE)
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
ADD<7:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set 0’ = Bit is cleared
Master mode:
bit 7-0 ADD<7:0>: Baud Rate Clock Divider bits
SCL pin clock period = ((ADD<7:0> + 1) *4)/FOSC
10-Bit Slave mode — Most Significant Address byte:
bit 7-3 Not used: Unused for Most Significant Address byte. Bit state of this register is a “don’t care”. Bit pat-
tern sent by master is fixed by I2C specification and must be equal to ‘11110’. However, those bits are
compared by hardware and are not affected by the value in this register.
bit 2-1 ADD<2:1>: Two Most Significant bits of 10-bit address
bit 0 Not used: Unused in this mode. Bit state is a “don’t care”.
10-Bit Slave mode — Least Significant Address byte:
bit 7-0 ADD<7:0>: Eight Least Significant bits of 10-bit address
7-Bi t Slave mode:
bit 7-1 ADD<7:1>: 7-bit address
bit 0 Not used: Unused in this mode. Bit state is a “don’t care”.
2008-2011 Microchip Technology Inc. DS41364E-page 291
PIC16(L)F1934/6/7
25.0 ENHANCED UNIVERSAL
SYNCHRONOUS
ASYNCHRONOUS RECEIVER
TRANSMITTER (EUSART)
The Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) module is a serial I/O
communications peripheral. It contains all the clock
generators, shift registers and data buffers necessary
to perform an input or output serial data transfer
independent of device program execution. The
EUSART, also known as a Serial Communications
Interface (SCI), can be configured as a full-duplex
asynchronous system or half-duplex synchronous
system. Full-Duplex mode is useful for
communications with peripheral systems, such as CRT
terminals and personal computers. Half-Duplex
Synchronous mode is intended for communications
with peripheral devices, such as A/D or D/A integrated
circuits, serial EEPROMs or other microcontrollers.
These devices typically do not have internal clocks for
baud rate generation and require the external clock
signal provided by a master synchronous device.
The EUSART module includes the following capabilities:
Full-duplex asynchronous transmit and receive
Two-character input buffer
One-character output buffer
Programmable 8-bit or 9-bit character length
Address detection in 9-bit mode
Input buffer overrun error detection
Received character framing error detection
Half-duplex synchronous master
Half-duplex synchronous slave
Programmable clock polarity in synchronous
modes
Sleep operation
The EUSART module implements the following
additional features, making it ideally suited for use in
Local Interconnect Network (LIN) bus systems:
Automatic detection and calibration of the baud rate
Wake-up on Break reception
13-bit Break character transmit
Block diagrams of the EUSART transmitter and
receiver are shown in Figure 25-1 and Figure 25-2.
FIGURE 25-1: EUSART TRANSMIT BLOCK DIAGRAM
TXIF
TXIE
Interrupt
TXEN
TX9D
MSb LSb
Data Bus
TXREG Register
Transmit Shift Register (TSR)
(8) 0
TX9
TRMT SPEN
TX/CK pin
Pin Buffer
and Control
8
SPBRGL
SPBRGH
BRG16
FOSC ÷ n
n
+ 1 Multiplier x4 x16 x64
SYNC 1X00 0
BRGH X110 0
BRG16 X101 0
Baud Rate Generator
••
PIC16(L)F1934/6/7
DS41364E-page 292 2008-2011 Microchip Technology Inc.
FIGURE 25-2: EUSART RECEIVE BLOCK DIAGRAM
The operation of the EUSART module is controlled
through three registers:
Transmit Status and Control (TXSTA)
Receive Status and Control (RCSTA)
Baud Rate Control (BAUDCON)
These registers are detailed in Register 25-1,
Register 25-2 and Register 25-3, respectively.
When the receiver or transmitter section is not enabled
then the corresponding RX or TX pin may be used for
general purpose input and output.
RX/DT pin
Pin Buffer
and Control
SPEN
Data
Recovery
CREN OERR
FERR
RSR Register
MSb LSb
RX9D RCREG Register FIFO
Interrupt
RCIF
RCIE
Data Bus
8
Stop START
(8) 7 1 0
RX9
• • •
SPBRGLSPBRGH
BRG16
RCIDL
FOSC ÷ n
n
+ 1 Multiplier x4 x16 x64
SYNC 1X00 0
BRGH X110 0
BRG16 X101 0
Baud Rate Generator
2008-2011 Microchip Technology Inc. DS41364E-page 293
PIC16(L)F1934/6/7
25.1 EUSART Asynchronous Mode
The EUSART transmits and receives data using the
standard non-return-to-zero (NRZ) format. NRZ is
implemented with two levels: a VOH mark state which
represents a ‘1’ data bit, and a VOL space state which
represents a ‘0’ data bit. NRZ refers to the fact that
consecutively transmitted data bits of the same value
stay at the output level of that bit without returning to a
neutral level between each bit transmission. An NRZ
transmission port idles in the mark state. Each character
transmission consists of one Start bit followed by eight
or nine data bits and is always terminated by one or
more Stop bits. The Start bit is always a space and the
Stop bits are always marks. The most common data
format is 8 bits. Each transmitted bit persists for a period
of 1/(Baud Rate). An on-chip dedicated 8-bit/16-bit Baud
Rate Generator is used to derive standard baud rate
frequencies from the system oscillator. See Table 25-5
for examples of baud rate configurations.
The EUSART transmits and receives the LSb first. The
EUSART’s transmitter and receiver are functionally
independent, but share the same data format and baud
rate. Parity is not supported by the hardware, but can
be implemented in software and stored as the ninth
data bit.
25.1.1 EUSART ASYNCHRONOUS
TRANSMITTER
The EUSART transmitter block diagram is shown in
Figure 25-1. The heart of the transmitter is the serial
Transmit Shift Register (TSR), which is not directly
accessible by software. The TSR obtains its data from
the transmit buffer, which is the TXREG register.
25.1.1.1 Enabling the Transmitter
The EUSART transmitter is enabled for asynchronous
operations by configuring the following three control
bits:
•TXEN = 1
SYNC = 0
SPEN = 1
All other EUSART control bits are assumed to be in
their default state.
Setting the TXEN bit of the TXSTA register enables the
transmitter circuitry of the EUSART. Clearing the SYNC
bit of the TXSTA register configures the EUSART for
asynchronous operation. Setting the SPEN bit of the
RCSTA register enables the EUSART and automatically
configures the TX/CK I/O pin as an output. If the TX/CK
pin is shared with an analog peripheral, the analog I/O
function must be disabled by clearing the corresponding
ANSEL bit.
25.1.1.2 Transmitting Data
A transmission is initiated by writing a character to the
TXREG register. If this is the first character, or the
previous character has been completely flushed from
the TSR, the data in the TXREG is immediately
transferred to the TSR register. If the TSR still contains
all or part of a previous character, the new character
data is held in the TXREG until the Stop bit of the
previous character has been transmitted. The pending
character in the TXREG is then transferred to the TSR
in one TCY immediately following the Stop bit
transmission. The transmission of the Start bit, data bits
and Stop bit sequence commences immediately
following the transfer of the data to the TSR from the
TXREG.
25.1.1.3 Transmit Data Polarity
The polarity of the transmit data can be controlled with
the SCKP bit of the BAUDCON register. The default
state of this bit is ‘0’ which selects high true transmit Idle
and data bits. Setting the SCKP bit to ‘1’ will invert the
transmit data resulting in low true Idle and data bits. The
SCKP bit controls transmit data polarity in
Asynchronous mode only. In Synchronous mode, the
SCKP bit has a different function. See Section 25.4.1.2
“Clock Polarity.
25.1.1.4 Transmit Interrupt Flag
The TXIF interrupt flag bit of the PIR1 register is set
whenever the EUSART transmitter is enabled and no
character is being held for transmission in the TXREG.
In other words, the TXIF bit is only clear when the TSR
is busy with a character and a new character has been
queued for transmission in the TXREG. The TXIF flag bit
is not cleared immediately upon writing TXREG. TXIF
becomes valid in the second instruction cycle following
the write execution. Polling TXIF immediately following
the TXREG write will return invalid results. The TXIF bit
is read-only, it cannot be set or cleared by software.
The TXIF interrupt can be enabled by setting the TXIE
interrupt enable bit of the PIE1 register. However, the
TXIF flag bit will be set whenever the TXREG is empty,
regardless of the state of TXIE enable bit.
To use interrupts when transmitting data, set the TXIE
bit only when there is more data to send. Clear the
TXIE interrupt enable bit upon writing the last character
of the transmission to the TXREG.
Note 1: The TXIF Transmitter Interrupt flag is set
when the TXEN enable bit is set.
PIC16(L)F1934/6/7
DS41364E-page 294 2008-2011 Microchip Technology Inc.
25.1.1.5 TSR Status
The TRMT bit of the TXSTA register indicates the
status of the TSR register. This is a read-only bit. The
TRMT bit is set when the TSR register is empty and is
cleared when a character is transferred to the TSR
register from the TXREG. The TRMT bit remains clear
until all bits have been shifted out of the TSR register.
No interrupt logic is tied to this bit, so the user has to
poll this bit to determine the TSR status.
25.1.1.6 Transmitting 9-Bit Characters
The EUSART supports 9-bit character transmissions.
When the TX9 bit of the TXSTA register is set, the
EUSART will shift 9 bits out for each character transmit-
ted. The TX9D bit of the TXSTA register is the ninth,
and Most Significant, data bit. When transmitting 9-bit
data, the TX9D data bit must be written before writing
the 8 Least Significant bits into the TXREG. All nine bits
of data will be transferred to the TSR shift register
immediately after the TXREG is written.
A special 9-bit Address mode is available for use with
multiple receivers. See Section 25.1.2.7 “Address
Detection” for more information on the address mode.
25.1.1.7 Asynchronous Transmission Set-up:
1. Initialize the SPBRGH, SPBRGL register pair and
the BRGH and BRG16 bits to achieve the desired
baud rate (see Section 25.3 “EUSART Baud
Rate Generator (BRG)”).
2. Enable the asynchronous serial port by clearing
the SYNC bit and setting the SPEN bit.
3. If 9-bit transmission is desired, set the TX9 con-
trol bit. A set ninth data bit will indicate that the 8
Least Significant data bits are an address when
the receiver is set for address detection.
4. Set SCKP bit if inverted transmit is desired.
5. Enable the transmission by setting the TXEN
control bit. This will cause the TXIF interrupt bit
to be set.
6. If interrupts are desired, set the TXIE interrupt
enable bit of the PIE1 register. An interrupt will
occur immediately provided that the GIE and
PEIE bits of the INTCON register are also set.
7. If 9-bit transmission is selected, the ninth bit
should be loaded into the TX9D data bit.
8. Load 8-bit data into the TXREG register. This
will start the transmission.
FIGURE 25-3: ASYNCHRONOUS TRANSMISSION
FIGURE 25-4: ASYNCHRON OUS TRANSMISSION (BACK-TO-BACK)
Note: The TSR register is not mapped in data
memory, so it is not available to the user.
Word 1
Stop bit
Word 1
Transmit Shift Reg.
Start bit bit 0 bit 1 bit 7/8
Write to TXREG
Word 1
BRG Output
(Shift Clock)
TX/CK
TXIF bit
(Transmit Buffer
Reg. Empty Flag)
TRMT bit
(Transmit Shift
Reg. Empty Flag)
1 TCY
pin
Transmit Shift Reg.
Write to TXREG
BRG Output
(Shift Clock)
TX/CK
TRMT bit
(Transmit Shift
Reg. Empty Flag)
Word 1 Word 2
Word 1 Word 2
Start bit Stop bit Start bit
Transmit Shift Reg.
Word 1 Word 2
bit 0 bit 1 bit 7/8 bit 0
Note: This timing diagram shows two consecutive transmissions.
1 TCY
1 TCY
pin
TXIF bit
(Transmit Buffer
Reg. Empty Flag)
2008-2011 Microchip Technology Inc. DS41364E-page 295
PIC16(L)F1934/6/7
TABLE 25-1: SUMMARY OF REGISTERS ASSOCIATED WITH ASYNCHRONOUS TRANSMISSION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL SCKP BRG16 WUE ABDEN 302
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
SPBRGL BRG<7:0> 303*
SPBRGH BRG<15:8> 303*
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TXREG EUSART Transmit Data Register 293*
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: — = unimplemented location, read as ‘0’. Shaded cells are not used for Asynchronous Transmission.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 296 2008-2011 Microchip Technology Inc.
25.1.2 EUSART ASYNCHRONOUS
RECEIVER
The Asynchronous mode is typically used in RS-232
systems. The receiver block diagram is shown in
Figure 25-2. The data is received on the RX/DT pin and
drives the data recovery block. The data recovery block
is actually a high-speed shifter operating at 16 times
the baud rate, whereas the serial Receive Shift
Register (RSR) operates at the bit rate. When all 8 or 9
bits of the character have been shifted in, they are
immediately transferred to a two character
First-In-First-Out (FIFO) memory. The FIFO buffering
allows reception of two complete characters and the
start of a third character before software must start
servicing the EUSART receiver. The FIFO and RSR
registers are not directly accessible by software.
Access to the received data is via the RCREG register.
25.1.2.1 Enabling the Receiver
The EUSART receiver is enabled for asynchronous
operation by configuring the following three control bits:
CREN = 1
SYNC = 0
SPEN = 1
All other EUSART control bits are assumed to be in
their default state.
Setting the CREN bit of the RCSTA register enables the
receiver circuitry of the EUSART. Clearing the SYNC bit
of the TXSTA register configures the EUSART for
asynchronous operation. Setting the SPEN bit of the
RCSTA register enables the EUSART. The programmer
must set the corresponding TRIS bit to configure the
RX/DT I/O pin as an input.
25.1.2.2 Receiving Data
The receiver data recovery circuit initiates character
reception on the falling edge of the first bit. The first bit,
also known as the Start bit, is always a zero. The data
recovery circuit counts one-half bit time to the center of
the Start bit and verifies that the bit is still a zero. If it is
not a zero then the data recovery circuit aborts
character reception, without generating an error, and
resumes looking for the falling edge of the Start bit. If
the Start bit zero verification succeeds then the data
recovery circuit counts a full bit time to the center of the
next bit. The bit is then sampled by a majority detect
circuit and the resulting 0’ or ‘1’ is shifted into the RSR.
This repeats until all data bits have been sampled and
shifted into the RSR. One final bit time is measured and
the level sampled. This is the Stop bit, which is always
a ‘1’. If the data recovery circuit samples a ‘0’ in the
Stop bit position then a framing error is set for this
character, otherwise the framing error is cleared for this
character. See Section 25.1.2.4 “Receive Framing
Error” for more information on framing errors.
Immediately after all data bits and the Stop bit have
been received, the character in the RSR is transferred
to the EUSART receive FIFO and the RCIF interrupt
flag bit of the PIR1 register is set. The top character in
the FIFO is transferred out of the FIFO by reading the
RCREG register.
25.1.2.3 Receive Interrupts
The RCIF interrupt flag bit of the PIR1 register is set
whenever the EUSART receiver is enabled and there is
an unread character in the receive FIFO. The RCIF
interrupt flag bit is read-only, it cannot be set or cleared
by software.
RCIF interrupts are enabled by setting all of the
following bits:
RCIE interrupt enable bit of the PIE1 register
PEIE, Peripheral Interrupt Enable bit of the
INTCON register
GIE, Global Interrupt Enable bit of the INTCON
register
The RCIF interrupt flag bit will be set when there is an
unread character in the FIFO, regardless of the state of
interrupt enable bits.
Note 1: If the RX/DT function is on an analog pin,
the corresponding ANSEL bit must be
cleared for the receiver to function.
Note: If the receive FIFO is overrun, no additional
characters will be received until the overrun
condition is cleared. See Section 25.1.2.5
“Receive Overrun Error” for more
information on overrun errors.
2008-2011 Microchip Technology Inc. DS41364E-page 297
PIC16(L)F1934/6/7
25.1.2.4 Receive Framing Error
Each character in the receive FIFO buffer has a
corresponding framing error Status bit. A framing error
indicates that a Stop bit was not seen at the expected
time. The framing error status is accessed via the
FERR bit of the RCSTA register. The FERR bit
represents the status of the top unread character in the
receive FIFO. Therefore, the FERR bit must be read
before reading the RCREG.
The FERR bit is read-only and only applies to the top
unread character in the receive FIFO. A framing error
(FERR = 1) does not preclude reception of additional
characters. It is not necessary to clear the FERR bit.
Reading the next character from the FIFO buffer will
advance the FIFO to the next character and the next
corresponding framing error.
The FERR bit can be forced clear by clearing the SPEN
bit of the RCSTA register which resets the EUSART.
Clearing the CREN bit of the RCSTA register does not
affect the FERR bit. A framing error by itself does not
generate an interrupt.
25.1.2.5 Receive Overrun Error
The receive FIFO buffer can hold two characters. An
overrun error will be generated if a third character, in its
entirety, is received before the FIFO is accessed. When
this happens the OERR bit of the RCSTA register is set.
The characters already in the FIFO buffer can be read
but no additional characters will be received until the
error is cleared. The error must be cleared by either
clearing the CREN bit of the RCSTA register or by
resetting the EUSART by clearing the SPEN bit of the
RCSTA register.
25.1.2.6 Receiving 9-bit Characters
The EUSART supports 9-bit character reception. When
the RX9 bit of the RCSTA register is set the EUSART
will shift 9 bits into the RSR for each character
received. The RX9D bit of the RCSTA register is the
ninth and Most Significant data bit of the top unread
character in the receive FIFO. When reading 9-bit data
from the receive FIFO buffer, the RX9D data bit must
be read before reading the 8 Least Significant bits from
the RCREG.
25.1.2.7 Address Detection
A special Address Detection mode is available for use
when multiple receivers share the same transmission
line, such as in RS-485 systems. Address detection is
enabled by setting the ADDEN bit of the RCSTA
register.
Address detection requires 9-bit character reception.
When address detection is enabled, only characters
with the ninth data bit set will be transferred to the
receive FIFO buffer, thereby setting the RCIF interrupt
bit. All other characters will be ignored.
Upon receiving an address character, user software
determines if the address matches its own. Upon
address match, user software must disable address
detection by clearing the ADDEN bit before the next
Stop bit occurs. When user software detects the end of
the message, determined by the message protocol
used, software places the receiver back into the
Address Detection mode by setting the ADDEN bit.
Note: If all receive characters in the receive
FIFO have framing errors, repeated reads
of the RCREG will not clear the FERR bit.
PIC16(L)F1934/6/7
DS41364E-page 298 2008-2011 Microchip Technology Inc.
25.1.2.8 Asynchronous Reception Set-up:
1. Initialize the SPBRGH, SPBRGL register pair
and the BRGH and BRG16 bits to achieve the
desired baud rate (see Section 25.3 “EUSART
Baud Rate Generator (BRG)”).
2. Clear the ANSEL bit for the RX pin (if applicable).
3. Enable the serial port by setting the SPEN bit.
The SYNC bit must be clear for asynchronous
operation.
4. If interrupts are desired, set the RCIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
5. If 9-bit reception is desired, set the RX9 bit.
6. Enable reception by setting the CREN bit.
7. The RCIF interrupt flag bit will be set when a
character is transferred from the RSR to the
receive buffer. An interrupt will be generated if
the RCIE interrupt enable bit was also set.
8. Read the RCSTA register to get the error flags
and, if 9-bit data reception is enabled, the ninth
data bit.
9. Get the received 8 Least Significant data bits
from the receive buffer by reading the RCREG
register.
10. If an overrun occurred, clear the OERR flag by
clearing the CREN receiver enable bit.
25.1.2.9 9-bit Address Detection Mode Set-up
This mode would typically be used in RS-485 systems.
To set up an Asynchronous Reception with Address
Detect Enable:
1. Initialize the SPBRGH, SPBRGL register pair
and the BRGH and BRG16 bits to achieve the
desired baud rate (see Section 25.3 “EUSART
Baud Rate Generator (BRG)”).
2. Clear the ANSEL bit for the RX pin (if applicable).
3. Enable the serial port by setting the SPEN bit.
The SYNC bit must be clear for asynchronous
operation.
4. If interrupts are desired, set the RCIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
5. Enable 9-bit reception by setting the RX9 bit.
6. Enable address detection by setting the ADDEN
bit.
7. Enable reception by setting the CREN bit.
8. The RCIF interrupt flag bit will be set when a
character with the ninth bit set is transferred
from the RSR to the receive buffer. An interrupt
will be generated if the RCIE interrupt enable bit
was also set.
9. Read the RCSTA register to get the error flags.
The ninth data bit will always be set.
10. Get the received 8 Least Significant data bits
from the receive buffer by reading the RCREG
register. Software determines if this is the
device’s address.
11. If an overrun occurred, clear the OERR flag by
clearing the CREN receiver enable bit.
12. If the device has been addressed, clear the
ADDEN bit to allow all received data into the
receive buffer and generate interrupts.
FIGURE 25-5: ASYNCHRONOUS RECEPTION
Start
bit bit 7/8
bit 1bit 0 bit 7/8 bit 0Stop
bit
Start
bit
Start
bit
bit 7/8 Stop
bit
RX/DT pin
Reg
Rcv Buffer Reg.
Rcv Shift
Read Rcv
Buffer Reg.
RCREG
RCIF
(Interrupt Flag)
OERR bit
CREN
Word 1
RCREG
Word 2
RCREG
Stop
bit
Note: This timing diagram shows three words appearing on the RX input. The RCREG (receive buffer) is read after the third word,
causing the OERR (overrun) bit to be set.
RCIDL
2008-2011 Microchip Technology Inc. DS41364E-page 299
PIC16(L)F1934/6/7
TABLE 25-2: SUMMARY OF REGISTERS ASSOCIATED WITH ASYNCHRONOUS RECEPTION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL SCKP BRG16 —WUEABDEN 302
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
RCREG EUSART Receive Data Register 296*
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
SPBRGL BRG<7:0> 303*
SPBRGH BRG<15:8> 303*
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for asynchronous reception.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 300 2008-2011 Microchip Technology Inc.
25.2 Clock Accuracy with
Asynchronous Operation
The factory calibrates the internal oscillator block out-
put (INTOSC). However, the INTOSC frequency may
drift as VDD or temperature changes, and this directly
affects the asynchronous baud rate. Two methods may
be used to adjust the baud rate clock, but both require
a reference clock source of some kind.
The first (preferred) method uses the OSCTUNE
register to adjust the INTOSC output. Adjusting the
value in the OSCTUNE register allows for fine resolution
changes to the system clock source. See Section 5.2.2
“Internal Clock Sources” for more information.
The other method adjusts the value in the Baud Rate
Generator. This can be done automatically with the
Auto-Baud Detect feature (see Section 25.3.1
“Auto-Baud Detect). There may not be fine enough
resolution when adjusting the Baud Rate Generator to
compensate for a gradual change in the peripheral
clock frequency.
REGISTER 25-1: TXSTA: TRANSMIT STATUS AND CONTROL REGISTER
R/W-/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R-1/1 R/W-0/0
CSRC TX9 TXEN(1) SYNC SENDB BRGH TRMT TX9D
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 CSRC: Clock Source Select bit
Asynchronous mode:
Don’t care
Synchronous mode:
1 = Master mode (clock generated internally from BRG)
0 = Slave mode (clock from external source)
bit 6 TX9: 9-bit Transmit Enable bit
1 = Selects 9-bit transmission
0 = Selects 8-bit transmission
bit 5 TXEN: Transmit Enable bit(1)
1 = Transmit enabled
0 = Transmit disabled
bit 4 SYNC: EUSART Mode Select bit
1 = Synchronous mode
0 = Asynchronous mode
bit 3 SENDB: Send Break Character bit
Asynchronous mode:
1 = Send Sync Break on next transmission (cleared by hardware upon completion)
0 = Sync Break transmission completed
Synchronous mode:
Don’t care
bit 2 BRGH: High Baud Rate Select bit
Asynchronous mode:
1 = High speed
0 = Low speed
Synchronous mode:
Unused in this mode
bit 1 TRMT: Transmit Shift Register Status bit
1 = TSR empty
0 = TSR full
bit 0 TX9D: Ninth bit of Transmit Data
Can be address/data bit or a parity bit.
Note 1: SREN/CREN overrides TXEN in Sync mode.
2008-2011 Microchip Technology Inc. DS41364E-page 301
PIC16(L)F1934/6/7
REGISTER 25-2: RCSTA: RECEIVE STATUS AND CONTROL REGISTER(1)
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R-0/0 R-0/0 R-x/x
SPEN RX9 SREN CREN ADDEN FERR OERR RX9D
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 SPEN: Serial Port Enable bit
1 = Serial port enabled (configures RX/DT and TX/CK pins as serial port pins)
0 = Serial port disabled (held in Reset)
bit 6 RX9: 9-bit Receive Enable bit
1 = Selects 9-bit reception
0 = Selects 8-bit reception
bit 5 SREN: Single Receive Enable bit
Asynchronous mode:
Don’t care
Synchronous mode – Master:
1 = Enables single receive
0 = Disables single receive
This bit is cleared after reception is complete.
Synchronous mode – Slave
Don’t care
bit 4 CREN: Continuous Receive Enable bit
Asynchronous mode:
1 = Enables receiver
0 = Disables receiver
Synchronous mode:
1 = Enables continuous receive until enable bit CREN is cleared (CREN overrides SREN)
0 = Disables continuous receive
bit 3 ADDEN: Address Detect Enable bit
Asynchronous mode 9-bit (RX9 = 1):
1 = Enables address detection, enable interrupt and load the receive buffer when RSR<8> is set
0 = Disables address detection, all bytes are received and ninth bit can be used as parity bit
Asynchronous mode 8-bit (RX9 = 0):
Don’t care
bit 2 FERR: Framing Error bit
1 = Framing error (can be updated by reading RCREG register and receive next valid byte)
0 = No framing error
bit 1 OERR: Overrun Error bit
1 = Overrun error (can be cleared by clearing bit CREN)
0 = No overrun error
bit 0 RX9D: Ninth bit of Received Data
This can be address/data bit or a parity bit and must be calculated by user firmware.
PIC16(L)F1934/6/7
DS41364E-page 302 2008-2011 Microchip Technology Inc.
REGISTER 25-3: BAUDCON: BAUD RATE CONTROL REGISTER
R-0/0 R-1/1 U-0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0
ABDOVF RCIDL SCKP BRG16 WUE ABDEN
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 ABDOVF: Auto-Baud Detect Overflow bit
Asynchronous mode:
1 = Auto-baud timer overflowed
0 = Auto-baud timer did not overflow
Synchronous mode:
Don’t care
bit 6 RCIDL: Receive Idle Flag bit
Asynchronous mode:
1 = Receiver is Idle
0 = Start bit has been received and the receiver is receiving
Synchronous mode:
Don’t care
bit 5 Unimplemented: Read as ‘0
bit 4 SCKP: Synchronous Clock Polarity Select bit
Asynchronous mode:
1 = Transmit inverted data to the TX/CK pin
0 = Transmit non-inverted data to the TX/CK pin
Synchronous mode:
1 = Data is clocked on rising edge of the clock
0 = Data is clocked on falling edge of the clock
bit 3 BRG16: 16-bit Baud Rate Generator bit
1 = 16-bit Baud Rate Generator is used
0 = 8-bit Baud Rate Generator is used
bit 2 Unimplemented: Read as ‘0
bit 1 WUE: Wake-up Enable bit
Asynchronous mode:
1 = Receiver is waiting for a falling edge. No character will be received, byte RCIF will be set. WUE
will automatically clear after RCIF is set.
0 = Receiver is operating normally
Synchronous mode:
Don’t care
bit 0 ABDEN: Auto-Baud Detect Enable bit
Asynchronous mode:
1 = Auto-Baud Detect mode is enabled (clears when auto-baud is complete)
0 = Auto-Baud Detect mode is disabled
Synchronous mode:
Don’t care
2008-2011 Microchip Technology Inc. DS41364E-page 303
PIC16(L)F1934/6/7
25.3 EUSART Baud Rate Generator
(BRG)
The Baud Rate Generator (BRG) is an 8-bit or 16-bit
timer that is dedicated to the support of both the
asynchronous and synchronous EUSART operation.
By default, the BRG operates in 8-bit mode. Setting the
BRG16 bit of the BAUDCON register selects 16-bit
mode.
The SPBRGH, SPBRGL register pair determines the
period of the free running baud rate timer. In
Asynchronous mode the multiplier of the baud rate
period is determined by both the BRGH bit of the TXSTA
register and the BRG16 bit of the BAUDCON register. In
Synchronous mode, the BRGH bit is ignored.
Table 25-3 contains the formulas for determining the
baud rate. Example 25-1 provides a sample calculation
for determining the baud rate and baud rate error.
Typical baud rates and error values for various
asynchronous modes have been computed for your
convenience and are shown in Table 25-3. It may be
advantageous to use the high baud rate (BRGH = 1),
or the 16-bit BRG (BRG16 = 1) to reduce the baud rate
error. The 16-bit BRG mode is used to achieve slow
baud rates for fast oscillator frequencies.
Writing a new value to the SPBRGH, SPBRGL register
pair causes the BRG timer to be reset (or cleared). This
ensures that the BRG does not wait for a timer overflow
before outputting the new baud rate.
If the system clock is changed during an active receive
operation, a receive error or data loss may result. To
avoid this problem, check the status of the RCIDL bit to
make sure that the receive operation is Idle before
changing the system clock.
EXAMPLE 25-1: CALCULATIN G BAUD
RATE ERROR
For a device with FOSC of 16 MHz, desired baud rate
of 9600, Asynchronous mode, 8-bit BRG:
Solving for SPBRGH:SPBRGL:
X
FOSC
Desired Ba ud R at e
---------------------------------------------
64
--------------------------------------------- 1=
Desired Baud Rate FOSC
64 [SPBRGH:SPBRG] 1+
---------------------------------------------------------------------=
16000000
9600
------------------------
64
------------------------1=
25.04225==
Calculated Baud Rate 16000000
64 25 1+
---------------------------=
9615=
Error Calc. Bau d Rate Desire d B aud Rate
Desired Baud Rate
--------------------------------------------------------------------------------------------=
9615 9600
9600
---------------------------------- 0. 1 6%==
PIC16(L)F1934/6/7
DS41364E-page 304 2008-2011 Microchip Technology Inc.
TABLE 25-3: BAUD RATE FORMULAS
TABLE 25-4: SUMMARY OF REGISTERS ASSOCIATED WITH THE BAUD RATE GENERATOR
Configuration Bits BRG/EUSART Mode Baud Rate Formula
SYNC BRG16 BRGH
000 8-bit/Asynchronous FOSC/[64 (n+1)]
001 8-bit/Asynchronous FOSC/[16 (n+1)]
010 16-bit/Asynchronous
011 16-bit/Asynchronous
FOSC/[4 (n+1)]10x 8-bit/Synchronous
11x 16-bit/Synchronous
Legend: x = Don’t care, n = value of SPBRGH, SPBRGL register pair
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL SCKP BRG16 WUE ABDEN 302
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
SPBRGL BRG<7:0> 303*
SPBRGH BRG<15:8> 303*
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for the Baud Rate Generator.
* Page provides register information.
2008-2011 Microchip Technology Inc. DS41364E-page 305
PIC16(L)F1934/6/7
TABLE 25-5: BAUD RATES FOR ASYNCHRONOUS MODES
BAUD
RATE
SYNC = 0, BRGH = 0, BRG16 = 0
FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300—— —— —— ——
1200 1221 1.73 255 1200 0.00 239 1200 0.00 143
2400 2404 0.16 207 2404 0.16 129 2400 0.00 119 2400 0.00 71
9600 9615 0.16 51 9470 -1.36 32 9600 0.00 29 9600 0.00 17
10417 10417 0.00 47 10417 0.00 29 10286 -1.26 27 10165 -2.42 16
19.2k 19.23k 0.16 25 19.53k 1.73 15 19.20k 0.00 14 19.20k 0.00 8
57.6k 55.55k -3.55 3 57.60k 0.00 7 57.60k 0.00 2
115.2k
BAUD
RATE
SYNC = 0, BRGH = 0, BRG16 = 0
FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 300 0.16 207 300 0.00 191 300 0.16 51
1200 1202 0.16 103 1202 0.16 51 1200 0.00 47 1202 0.16 12
2400 2404 0.16 51 2404 0.16 25 2400 0.00 23
9600 9615 0.16 12 9600 0.00 5
10417 10417 0.00 11 10417 0.00 5
19.2k 19.20k 0.00 2
57.6k 57.60k 0.00 0
115.2k
BAUD
RATE
SYNC = 0, BRGH = 1, BRG16 = 0
FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 —— —— —— ——
1200
2400 ——
9600 9615 0.16 207 9615 0.16 129 9600 0.00 119 9600 0.00 71
10417 10417 0.00 191 10417 0.00 119 10378 -0.37 110 10473 0.53 65
19.2k 19.23k 0.16 103 19.23k 0.16 64 19.20k 0.00 59 19.20k 0.00 35
57.6k 57.14k -0.79 34 56.82k -1.36 21 57.60k 0.00 19 57.60k 0.00 11
115.2k 117.64k 2.12 16 113.64k -1.36 10 115.2k 0.00 9 115.2k 0.00 5
PIC16(L)F1934/6/7
DS41364E-page 306 2008-2011 Microchip Technology Inc.
BAUD
RATE
SYNC = 0, BRGH = 1, BRG16 = 0
FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 —— 300 0.16 207
1200 1202 0.16 207 1200 0.00 191 1202 0.16 51
2400 2404 0.16 207 2404 0.16 103 2400 0.00 95 2404 0.16 25
9600 9615 0.16 51 9615 0.16 25 9600 0.00 23
10417 10417 0.00 47 10417 0.00 23 10473 0.53 21 10417 0.00 5
19.2k 19231 0.16 25 19.23k 0.16 12 19.2k 0.00 11
57.6k 55556 -3.55 8 57.60k 0.00 3
115.2k 115.2k 0.00 1
BAUD
RATE
SYNC = 0, BRGH = 0, BRG16 = 1
FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 300.0 0.00 6666 300.0 -0.01 4166 300.0 0.00 3839 300.0 0.00 2303
1200 1200 -0.02 3332 1200 -0.03 1041 1200 0.00 959 1200 0.00 575
2400 2401 -0.04 832 2399 -0.03 520 2400 0.00 479 2400 0.00 287
9600 9615 0.16 207 9615 0.16 129 9600 0.00 119 9600 0.00 71
10417 10417 0.00 191 10417 0.00 119 10378 -0.37 110 10473 0.53 65
19.2k 19.23k 0.16 103 19.23k 0.16 64 19.20k 0.00 59 19.20k 0.00 35
57.6k 57.14k -0.79 34 56.818 -1.36 21 57.60k 0.00 19 57.60k 0.00 11
115.2k 117.6k 2.12 16 113.636 -1.36 10 115.2k 0.00 9 115.2k 0.00 5
BAUD
RATE
SYNC = 0, BRGH = 0, BRG16 = 1
FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 299.9 -0.02 1666 300.1 0.04 832 300.0 0.00 767 300.5 0.16 207
1200 1199 -0.08 416 1202 0.16 207 1200 0.00 191 1202 0.16 51
2400 2404 0.16 207 2404 0.16 103 2400 0.00 95 2404 0.16 25
9600 9615 0.16 51 9615 0.16 25 9600 0.00 23
10417 10417 0.00 47 10417 0.00 23 10473 0.53 21 10417 0.00 5
19.2k 19.23k 0.16 25 19.23k 0.16 12 19.20k 0.00 11
57.6k 55556 -3.55 8 57.60k 0.00 3
115.2k 115.2k 0.00 1
TABLE 25-5: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED)
2008-2011 Microchip Technology Inc. DS41364E-page 307
PIC16(L)F1934/6/7
BAUD
RATE
SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1
FOSC = 32.000 MHz FOSC = 20.000 MHz FOSC = 18.432 MHz FOSC = 11.0592 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 300.0 0.00 26666 300.0 0.00 16665 300.0 0.00 15359 300.0 0.00 9215
1200 1200 0.00 6666 1200 -0.01 4166 1200 0.00 3839 1200 0.00 2303
2400 2400 0.01 3332 2400 0.02 2082 2400 0.00 1919 2400 0.00 1151
9600 9604 0.04 832 9597 -0.03 520 9600 0.00 479 9600 0.00 287
10417 10417 0.00 767 10417 0.00 479 10425 0.08 441 10433 0.16 264
19.2k 19.18k -0.08 416 19.23k 0.16 259 19.20k 0.00 239 19.20k 0.00 143
57.6k 57.55k -0.08 138 57.47k -0.22 86 57.60k 0.00 79 57.60k 0.00 47
115.2k 115.9k 0.64 68 116.3k 0.94 42 115.2k 0.00 39 115.2k 0.00 23
BAUD
RATE
SYNC = 0, BRGH = 1, BRG16 = 1 or SYNC = 1, BRG16 = 1
FOSC = 8.000 MHz FOSC = 4.000 MHz FOSC = 3.6864 MHz FOSC = 1.000 MHz
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
Actual
Rate %
Error
SPBRG
value
(decimal)
300 300.0 0.00 6666 300.0 0.01 3332 300.0 0.00 3071 300.1 0.04 832
1200 1200 -0.02 1666 1200 0.04 832 1200 0.00 767 1202 0.16 207
2400 2401 0.04 832 2398 0.08 416 2400 0.00 383 2404 0.16 103
9600 9615 0.16 207 9615 0.16 103 9600 0.00 95 9615 0.16 25
10417 10417 0 191 10417 0.00 95 10473 0.53 87 10417 0.00 23
19.2k 19.23k 0.16 103 19.23k 0.16 51 19.20k 0.00 47 19.23k 0.16 12
57.6k 57.14k -0.79 34 58.82k 2.12 16 57.60k 0.00 15
115.2k 117.6k 2.12 16 111.1k -3.55 8 115.2k 0.00 7
TABLE 25-5: BAUD RATES FOR ASYNCHRONOUS MODES (CONTINUED)
PIC16(L)F1934/6/7
DS41364E-page 308 2008-2011 Microchip Technology Inc.
25.3.1 AUTO-BAUD DETECT
The EUSART module supports automatic detection
and calibration of the baud rate.
In the Auto-Baud Detect (ABD) mode, the clock to the
BRG is reversed. Rather than the BRG clocking the
incoming RX signal, the RX signal is timing the BRG.
The Baud Rate Generator is used to time the period of
a received 55h (ASCII “U”) which is the Sync character
for the LIN bus. The unique feature of this character is
that it has five rising edges including the Stop bit edge.
Setting the ABDEN bit of the BAUDCON register starts
the auto-baud calibration sequence (Figure 25-6).
While the ABD sequence takes place, the EUSART
state machine is held in Idle. On the first rising edge of
the receive line, after the Start bit, the SPBRG begins
counting up using the BRG counter clock as shown in
Table 25-6. The fifth rising edge will occur on the RX pin
at the end of the eighth bit period. At that time, an
accumulated value totaling the proper BRG period is
left in the SPBRGH, SPBRGL register pair, the ABDEN
bit is automatically cleared and the RCIF interrupt flag
is set. The value in the RCREG needs to be read to
clear the RCIF interrupt. RCREG content should be
discarded. When calibrating for modes that do not use
the SPBRGH register the user can verify that the
SPBRGL register did not overflow by checking for 00h
in the SPBRGH register.
The BRG auto-baud clock is determined by the BRG16
and BRGH bits as shown in Table 25-6. During ABD,
both the SPBRGH and SPBRGL registers are used as
a 16-bit counter, independent of the BRG16 bit setting.
While calibrating the baud rate period, the SPBRGH
and SPBRGL registers are clocked at 1/8th the BRG
base clock rate. The resulting byte measurement is the
average bit time when clocked at full speed.
TABLE 25-6: BRG COUNTER CLOCK RATES
FIGURE 25-6: AUTOMATIC BAUD RATE CALIBRATION
Note 1: If the WUE bit is set with the ABDEN bit,
auto-baud detection will occur on the byte
following the Break character (see
Section 25.3.3 “Auto-Wake-up on
Break”).
2: It is up to the user to determine that the
incoming character baud rate is within the
range of the selected BRG clock source.
Some combinations of oscillator frequency
and EUSART baud rates are not possible.
3: During the auto-baud process, the
auto-baud counter starts counting at 1.
Upon completion of the auto-baud
sequence, to achieve maximum accuracy,
subtract 1 from the SPBRGH:SPBRGL
register pair.
BRG16 BRGH BRG Base
Clock BRG ABD
Clock
00FOSC/64 FOSC/512
01FOSC/16 FOSC/128
10FOSC/16 FOSC/128
11 FOSC/4 FOSC/32
Note: During the ABD sequence, SPBRGL and
SPBRGH registers are both used as a 16-bit
counter, independent of BRG16 setting.
BRG Value
RX pin
ABDEN bit
RCIF bit
bit 0 bit 1
(Interrupt)
Read
RCREG
BRG Clock
Start
Auto Cleared
Set by User
XXXXh 0000h
Edge #1
bit 2 bit 3
Edge #2
bit 4 bit 5
Edge #3
bit 6 bit 7
Edge #4
Stop bit
Edge #5
001Ch
Note 1: The ABD sequence requires the EUSART module to be configured in Asynchronous mode.
SPBRGL XXh 1Ch
SPBRGH XXh 00h
RCIDL
2008-2011 Microchip Technology Inc. DS41364E-page 309
PIC16(L)F1934/6/7
25.3.2 AUTO-BAUD OVERFLOW
During the course of automatic baud detection, the
ABDOVF bit of the BAUDCON register will be set if the
baud rate counter overflows before the fifth rising edge
is detected on the RX pin. The ABDOVF bit indicates
that the counter has exceeded the maximum count that
can fit in the 16 bits of the SPBRGH:SPBRGL register
pair. After the ABDOVF has been set, the counter con-
tinues to count until the fifth rising edge is detected on
the RX pin. Upon detecting the fifth RX edge, the hard-
ware will set the RCIF interrupt flag and clear the
ABDEN bit of the BAUDCON register. The RCIF flag
can be subsequently cleared by reading the RCREG
register. The ABDOVF flag of the BAUDCON register
can be cleared by software directly.
To terminate the auto-baud process before the RCIF
flag is set, clear the ABDEN bit then clear the ABDOVF
bit of the BAUDCON register. The ABDOVF bit will
remain set if the ABDEN bit is not cleared first.
25.3.3 AUTO-WAKE-UP ON BREAK
During Sleep mode, all clocks to the EUSART are
suspended. Because of this, the Baud Rate Generator
is inactive and a proper character reception cannot be
performed. The Auto-Wake-up feature allows the
controller to wake-up due to activity on the RX/DT line.
This feature is available only in Asynchronous mode.
The Auto-Wake-up feature is enabled by setting the
WUE bit of the BAUDCON register. Once set, the normal
receive sequence on RX/DT is disabled, and the
EUSART remains in an Idle state, monitoring for a
wake-up event independent of the CPU mode. A
wake-up event consists of a high-to-low transition on the
RX/DT line. (This coincides with the start of a Sync Break
or a wake-up signal character for the LIN protocol.)
The EUSART module generates an RCIF interrupt
coincident with the wake-up event. The interrupt is
generated synchronously to the Q clocks in normal CPU
operating modes (Figure 25-7), and asynchronously if
the device is in Sleep mode (Figure 25-8). The interrupt
condition is cleared by reading the RCREG register.
The WUE bit is automatically cleared by the low-to-high
transition on the RX line at the end of the Break. This
signals to the user that the Break event is over. At this
point, the EUSART module is in Idle mode waiting to
receive the next character.
25.3.3.1 Special Considerations
Break Character
To avoid character errors or character fragments during
a wake-up event, the wake-up character must be all
zeros.
When the wake-up is enabled the function works
independent of the low time on the data stream. If the
WUE bit is set and a valid non-zero character is
received, the low time from the Start bit to the first rising
edge will be interpreted as the wake-up event. The
remaining bits in the character will be received as a
fragmented character and subsequent characters can
result in framing or overrun errors.
Therefore, the initial character in the transmission must
be all ‘0s. This must be 10 or more bit times, 13-bit
times recommended for LIN bus, or any number of bit
times for standard RS-232 devices.
Oscillator Start-up Time
Oscillator start-up time must be considered, especially
in applications using oscillators with longer start-up
intervals (i.e., LP, XT or HS/PLL mode). The Sync
Break (or wake-up signal) character must be of
sufficient length, and be followed by a sufficient
interval, to allow enough time for the selected oscillator
to start and provide proper initialization of the EUSART.
WUE Bit
The wake-up event causes a receive interrupt by
setting the RCIF bit. The WUE bit is cleared in
hardware by a rising edge on RX/DT. The interrupt
condition is then cleared in software by reading the
RCREG register and discarding its contents.
To ensure that no actual data is lost, check the RCIDL
bit to verify that a receive operation is not in process
before setting the WUE bit. If a receive operation is not
occurring, the WUE bit may then be set just prior to
entering the Sleep mode.
PIC16(L)F1934/6/7
DS41364E-page 310 2008-2011 Microchip Technology Inc.
FIGURE 25-7: AUTO-WAKE-UP BIT (WUE) TIMING DURING NORMAL OPERATION
FIGURE 25-8: AUTO-WAKE-UP BIT (WUE) TIMINGS DURING SLEEP
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4
OSC1
WUE bit
RX/DT Line
RCIF
Bit set by user Auto Cleared
Cleared due to User Read of RCREG
Note 1: The EUSART remains in Idle while the WUE bit is set.
Q1Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1Q2 Q3 Q4
OSC1
WUE bit
RX/DT Line
RCIF
Bit Set by User Auto Cleared
Cleared due to User Read of RCREG
Sleep Command Executed
Note 1
Note 1: If the wake-up event requires long oscillator warm-up time, the automatic clearing of the WUE bit can occur while the stposc signal is
still active. This sequence should not depend on the presence of Q clocks.
2: The EUSART remains in Idle while the WUE bit is set.
Sleep Ends
2008-2011 Microchip Technology Inc. DS41364E-page 311
PIC16(L)F1934/6/7
25.3.4 BREAK CHARACTER SEQUENCE
The EUSART module has the capability of sending the
special Break character sequences that are required by
the LIN bus standard. A Break character consists of a
Start bit, followed by 12 ‘0bits and a Stop bit.
To send a Break character, set the SENDB and TXEN
bits of the TXSTA register. The Break character trans-
mission is then initiated by a write to the TXREG. The
value of data written to TXREG will be ignored and all
0’s will be transmitted.
The SENDB bit is automatically reset by hardware after
the corresponding Stop bit is sent. This allows the user
to preload the transmit FIFO with the next transmit byte
following the Break character (typically, the Sync
character in the LIN specification).
The TRMT bit of the TXSTA register indicates when the
transmit operation is active or Idle, just as it does during
normal transmission. See Figure 25-9 for the timing of
the Break character sequence.
25.3.4.1 Break and Sync Transmit Sequence
The following sequence will start a message frame
header made up of a Break, followed by an auto-baud
Sync byte. This sequence is typical of a LIN bus
master.
1. Configure the EUSART for the desired mode.
2. Set the TXEN and SENDB bits to enable the
Break sequence.
3. Load the TXREG with a dummy character to
initiate transmission (the value is ignored).
4. Write ‘55h’ to TXREG to load the Sync character
into the transmit FIFO buffer.
5. After the Break has been sent, the SENDB bit is
reset by hardware and the Sync character is
then transmitted.
When the TXREG becomes empty, as indicated by the
TXIF, the next data byte can be written to TXREG.
25.3.5 RECEIVING A BREAK CHARACTER
The Enhanced EUSART module can receive a Break
character in two ways.
The first method to detect a Break character uses the
FERR bit of the RCSTA register and the Received data
as indicated by RCREG. The Baud Rate Generator is
assumed to have been initialized to the expected baud
rate.
A Break character has been received when;
RCIF bit is set
FERR bit is set
RCREG = 00h
The second method uses the Auto-Wake-up feature
described in Section 25.3.3 “Auto-Wake-up on
Break”. By enabling this feature, the EUSART will
sample the next two transitions on RX/DT, cause an
RCIF interrupt, and receive the next data byte followed
by another interrupt.
Note that following a Break character, the user will
typically want to enable the Auto-Baud Detect feature.
For both methods, the user can set the ABDEN bit of
the BAUDCON register before placing the EUSART in
Sleep mode.
FIGURE 25-9: SEND BREAK CHARACTER SEQUENCE
Write to TXREG Dummy Write
BRG Output
(Shift Clock)
Start bit bit 0 bit 1 bit 11 Stop bit
Break
TXIF bit
(Transmit
Interrupt Flag)
TX (pin)
TRMT bit
(Transmit Shift
Empty Flag)
SENDB
(send Break
control bit)
SENDB Sampled Here Auto Cleared
PIC16(L)F1934/6/7
DS41364E-page 312 2008-2011 Microchip Technology Inc.
25.4 EUSART Synchronous Mode
Synchronous serial communications are typically used
in systems with a single master and one or more
slaves. The master device contains the necessary cir-
cuitry for baud rate generation and supplies the clock
for all devices in the system. Slave devices can take
advantage of the master clock by eliminating the inter-
nal clock generation circuitry.
There are two signal lines in Synchronous mode: a bidi-
rectional data line and a clock line. Slaves use the
external clock supplied by the master to shift the serial
data into and out of their respective receive and trans-
mit shift registers. Since the data line is bidirectional,
synchronous operation is half-duplex only. Half-duplex
refers to the fact that master and slave devices can
receive and transmit data but not both simultaneously.
The EUSART can operate as either a master or slave
device.
Start and Stop bits are not used in synchronous trans-
missions.
25.4.1 SYNCHRONOUS MASTER MODE
The following bits are used to configure the EUSART
for Synchronous Master operation:
SYNC = 1
CSRC = 1
SREN = 0 (for transmit); SREN = 1 (for receive)
CREN = 0 (for transmit); CREN = 1 (for receive)
SPEN = 1
Setting the SYNC bit of the TXSTA register configures
the device for synchronous operation. Setting the CSRC
bit of the TXSTA register configures the device as a
master. Clearing the SREN and CREN bits of the RCSTA
register ensures that the device is in the Transmit mode,
otherwise the device will be configured to receive. Setting
the SPEN bit of the RCSTA register enables the
EUSART.
25.4.1.1 Master Clock
Synchronous data transfers use a separate clock line,
which is synchronous with the data. A device config-
ured as a master transmits the clock on the TX/CK line.
The TX/CK pin output driver is automatically enabled
when the EUSART is configured for synchronous
transmit or receive operation. Serial data bits change
on the leading edge to ensure they are valid at the trail-
ing edge of each clock. One clock cycle is generated
for each data bit. Only as many clock cycles are gener-
ated as there are data bits.
25.4.1.2 Clock Polarity
A clock polarity option is provided for Microwire
compatibility. Clock polarity is selected with the SCKP
bit of the BAUDCON register. Setting the SCKP bit sets
the clock Idle state as high. When the SCKP bit is set,
the data changes on the falling edge of each clock.
Clearing the SCKP bit sets the Idle state as low. When
the SCKP bit is cleared, the data changes on the rising
edge of each clock.
25.4.1.3 Synchronous Master Transmission
Data is transferred out of the device on the RX/DT pin.
The RX/DT and TX/CK pin output drivers are automat-
ically enabled when the EUSART is configured for syn-
chronous master transmit operation.
A transmission is initiated by writing a character to the
TXREG register. If the TSR still contains all or part of a
previous character the new character data is held in the
TXREG until the last bit of the previous character has
been transmitted. If this is the first character, or the pre-
vious character has been completely flushed from the
TSR, the data in the TXREG is immediately transferred
to the TSR. The transmission of the character com-
mences immediately following the transfer of the data
to the TSR from the TXREG.
Each data bit changes on the leading edge of the mas-
ter clock and remains valid until the subsequent leading
clock edge.
25.4.1.4 Synchronous Master Transmission
Set-up:
1. Initialize the SPBRGH, SPBRGL register pair
and the BRGH and BRG16 bits to achieve the
desired baud rate (see Section 25.3 “EUSART
Baud Rate Generator (BRG)”).
2. Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
3. Disable Receive mode by clearing bits SREN
and CREN.
4. Enable Transmit mode by setting the TXEN bit.
5. If 9-bit transmission is desired, set the TX9 bit.
6. If interrupts are desired, set the TXIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
7. If 9-bit transmission is selected, the ninth bit
should be loaded in the TX9D bit.
8. Start transmission by loading data to the TXREG
register.
Note: The TSR register is not mapped in data
memory, so it is not available to the user.
2008-2011 Microchip Technology Inc. DS41364E-page 313
PIC16(L)F1934/6/7
FIGURE 25-10: SYNCHRONOUS TRANSMISSION
FIGURE 25-11: SYNCHRONOUS TRANSMISSION (THROUGH TXEN)
TABLE 25-7: SUMMARY OF REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER
TRANSMISSION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL SCKP BRG16 WUE ABDEN 302
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
SPBRGL BRG<7:0> 303*
SPBRGH BRG<15:8> 303*
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TXREG EUSART Transmit Data Register 293*
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: = unimplemented read as ‘0’. Shaded cells are not used for synchronous master transmission.
* Page provides register information.
bit 0 bit 1 bit 7
Word 1
bit 2 bit 0 bit 1 bit 7
RX/DT
Write to
TXREG Reg
TXIF bit
(Interrupt Flag)
TXEN bit 1 1
Word 2
TRMT bit
Write Word 1 Write Word 2
Note: Sync Master mode, SPBRGL = 0, continuous transmission of two 8-bit words.
pin
TX/CK pin
TX/CK pin
(SCKP = 0)
(SCKP = 1)
RX/DT pin
TX/CK pin
Write to
TXREG reg
TXIF bit
TRMT bit
bit 0 bit 1 bit 2 bit 6 bit 7
TXEN bit
PIC16(L)F1934/6/7
DS41364E-page 314 2008-2011 Microchip Technology Inc.
25.4.1.5 Synchronous Master Reception
Data is received at the RX/DT pin. The RX/DT pin
output driver is automatically disabled when the
EUSART is configured for synchronous master receive
operation.
In Synchronous mode, reception is enabled by setting
either the Single Receive Enable bit (SREN of the
RCSTA register) or the Continuous Receive Enable bit
(CREN of the RCSTA register).
When SREN is set and CREN is clear, only as many
clock cycles are generated as there are data bits in a
single character. The SREN bit is automatically cleared
at the completion of one character. When CREN is set,
clocks are continuously generated until CREN is
cleared. If CREN is cleared in the middle of a character
the CK clock stops immediately and the partial charac-
ter is discarded. If SREN and CREN are both set, then
SREN is cleared at the completion of the first character
and CREN takes precedence.
To initiate reception, set either SREN or CREN. Data is
sampled at the RX/DT pin on the trailing edge of the
TX/CK clock pin and is shifted into the Receive Shift
Register (RSR). When a complete character is
received into the RSR, the RCIF bit is set and the char-
acter is automatically transferred to the two character
receive FIFO. The Least Significant eight bits of the top
character in the receive FIFO are available in RCREG.
The RCIF bit remains set as long as there are unread
characters in the receive FIFO.
25.4.1.6 Slave Clock
Synchronous data transfers use a separate clock line,
which is synchronous with the data. A device configured
as a slave receives the clock on the TX/CK line. The
TX/CK pin output driver is automatically disabled when
the device is configured for synchronous slave transmit
or receive operation. Serial data bits change on the
leading edge to ensure they are valid at the trailing edge
of each clock. One data bit is transferred for each clock
cycle. Only as many clock cycles should be received as
there are data bits.
25.4.1.7 Receive Overrun Error
The receive FIFO buffer can hold two characters. An
overrun error will be generated if a third character, in its
entirety, is received before RCREG is read to access
the FIFO. When this happens the OERR bit of the
RCSTA register is set. Previous data in the FIFO will
not be overwritten. The two characters in the FIFO
buffer can be read, however, no additional characters
will be received until the error is cleared. The OERR bit
can only be cleared by clearing the overrun condition.
If the overrun error occurred when the SREN bit is set
and CREN is clear then the error is cleared by reading
RCREG. If the overrun occurred when the CREN bit is
set then the error condition is cleared by either clearing
the CREN bit of the RCSTA register or by clearing the
SPEN bit which resets the EUSART.
25.4.1.8 Receiving 9-bit Characters
The EUSART supports 9-bit character reception. When
the RX9 bit of the RCSTA register is set the EUSART
will shift 9-bits into the RSR for each character
received. The RX9D bit of the RCSTA register is the
ninth, and Most Significant, data bit of the top unread
character in the receive FIFO. When reading 9-bit data
from the receive FIFO buffer, the RX9D data bit must
be read before reading the 8 Least Significant bits from
the RCREG.
25.4.1.9 Synchronous Master Reception
Set-up:
1. Initialize the SPBRGH, SPBRGL register pair for
the appropriate baud rate. Set or clear the
BRGH and BRG16 bits, as required, to achieve
the desired baud rate.
2. Clear the ANSEL bit for the RX pin (if applicable).
3. Enable the synchronous master serial port by
setting bits SYNC, SPEN and CSRC.
4. Ensure bits CREN and SREN are clear.
5. If interrupts are desired, set the RCIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
6. If 9-bit reception is desired, set bit RX9.
7. Start reception by setting the SREN bit or for
continuous reception, set the CREN bit.
8. Interrupt flag bit RCIF will be set when reception
of a character is complete. An interrupt will be
generated if the enable bit RCIE was set.
9. Read the RCSTA register to get the ninth bit (if
enabled) and determine if any error occurred
during reception.
10. Read the 8-bit received data by reading the
RCREG register.
11. If an overrun error occurs, clear the error by
either clearing the CREN bit of the RCSTA
register or by clearing the SPEN bit which resets
the EUSART.
2008-2011 Microchip Technology Inc. DS41364E-page 315
PIC16(L)F1934/6/7
FIGURE 25-12: SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
TABLE 25-8: SUMMARY OF REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER
RECEPTION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL SCKP BRG16 WUE ABDEN 302
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
RCREG EUSART Receive Data Register 296*
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
SPBRGL BRG<7:0> 303*
SPBRGH BRG<15:8> 303*
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for synchronous master reception.
* Page provides register information.
CREN bit
RX/DT
Write to
bit SREN
SREN bit
RCIF bit
(Interrupt)
Read
RXREG
0
bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7
0
Note: Timing diagram demonstrates Sync Master mode with bit SREN = 1 and bit BRGH = 0.
TX/CK pin
TX/CK pin
pin
(SCKP = 0)
(SCKP = 1)
PIC16(L)F1934/6/7
DS41364E-page 316 2008-2011 Microchip Technology Inc.
25.4.2 SYNCHRONOUS SLAVE MODE
The following bits are used to configure the EUSART
for Synchronous slave operation:
SYNC = 1
CSRC = 0
SREN = 0 (for transmit); SREN = 1 (for receive)
CREN = 0 (for transmit); CREN = 1 (for receive)
SPEN = 1
Setting the SYNC bit of the TXSTA register configures the
device for synchronous operation. Clearing the CSRC bit
of the TXSTA register configures the device as a slave.
Clearing the SREN and CREN bits of the RCSTA register
ensures that the device is in the Transmit mode,
otherwise the device will be configured to receive. Setting
the SPEN bit of the RCSTA register enables the
EUSART.
25.4.2.1 EUSART Synchronous Slave
Transmit
The operation of the Synchronous Master and Slave
modes are identical (see Section 25.4.1.3
“Synchronous Master Transmission”), except in the
case of the Sleep mode.
If two words are written to the TXREG and then the
SLEEP instruction is executed, the following will occur:
1. The first character will immediately transfer to
the TSR register and transmit.
2. The second word will remain in TXREG register.
3. The TXIF bit will not be set.
4. After the first character has been shifted out of
TSR, the TXREG register will transfer the second
character to the TSR and the TXIF bit will now be
set.
5. If the PEIE and TXIE bits are set, the interrupt
will wake the device from Sleep and execute the
next instruction. If the GIE bit is also set, the
program will call the Interrupt Service Routine.
25.4.2.2 Synchronous Slave Transmission
Set-up:
1. Set the SYNC and SPEN bits and clear the
CSRC bit.
2. Clear the ANSEL bit for the CK pin (if applicable).
3. Clear the CREN and SREN bits.
4. If interrupts are desired, set the TXIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
5. If 9-bit transmission is desired, set the TX9 bit.
6. Enable transmission by setting the TXEN bit.
7. If 9-bit transmission is selected, insert the Most
Significant bit into the TX9D bit.
8. Start transmission by writing the Least
Significant 8 bits to the TXREG register.
TABLE 25-9: SUMMARY OF REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE
TRANSMISSION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL —SCKPBRG16 WUE ABDEN 302
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TXREG EUSART Transmit Data Register 293*
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for synchronous slave transmission.
* Page provides register information.
2008-2011 Microchip Technology Inc. DS41364E-page 317
PIC16(L)F1934/6/7
25.4.2.3 EUSART Synchronous Slave
Reception
The operation of the Synchronous Master and Slave
modes is identical (Section 25.4.1.5 “Synchronous
Master Reception”), with the following exceptions:
Sleep
CREN bit is always set, therefore the receiver is
never Idle
SREN bit, which is a “don’t care” in Slave mode
A character may be received while in Sleep mode by
setting the CREN bit prior to entering Sleep. Once the
word is received, the RSR register will transfer the data
to the RCREG register. If the RCIE enable bit is set, the
interrupt generated will wake the device from Sleep
and execute the next instruction. If the GIE bit is also
set, the program will branch to the interrupt vector.
25.4.2.4 Synchronous Slave Reception
Set-up:
1. Set the SYNC and SPEN bits and clear the
CSRC bit.
2. Clear the ANSEL bit for both the CK and DT pins
(if applicable).
3. If interrupts are desired, set the RCIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
4. If 9-bit reception is desired, set the RX9 bit.
5. Set the CREN bit to enable reception.
6. The RCIF bit will be set when reception is
complete. An interrupt will be generated if the
RCIE bit was set.
7. If 9-bit mode is enabled, retrieve the Most
Significant bit from the RX9D bit of the RCSTA
register.
8. Retrieve the 8 Least Significant bits from the
receive FIFO by reading the RCREG register.
9. If an overrun error occurs, clear the error by
either clearing the CREN bit of the RCSTA
register or by clearing the SPEN bit which resets
the EUSART.
TABLE 25-10: SUMMARY OF REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE
RECEPTION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
BAUDCON ABDOVF RCIDL —SCKPBRG16 WUE ABDEN 302
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
PIE1 TMR1GIE ADIE RCIE TXIE SSPIE CCP1IE TMR2IE TMR1IE 99
PIR1 TMR1GIF ADIF RCIF TXIF SSPIF CCP1IF TMR2IF TMR1IF 102
RCREG EUSART Receive Data Register 296*
RCSTA SPEN RX9 SREN CREN ADDEN FERR OERR RX9D 301
TRISC TRISC7 TRISC6 TRISC5 TRISC4 TRISC3 TRISC2 TRISC1 TRISC0 142
TXSTA CSRC TX9 TXEN SYNC SENDB BRGH TRMT TX9D 300
Legend: — = unimplemented read as ‘0’. Shaded cells are not used for synchronous slave reception.
* Page provides register information.
PIC16(L)F1934/6/7
DS41364E-page 318 2008-2011 Microchip Technology Inc.
25.5 EUSART Operation During Sleep
The EUSART will remain active during Sleep only in the
Synchronous Slave mode. All other modes require the
system clock and therefore cannot generate the neces-
sary signals to run the Transmit or Receive Shift regis-
ters during Sleep.
Synchronous Slave mode uses an externally generated
clock to run the Transmit and Receive Shift registers.
25.5.1 SYNCHRONOUS RECEIVE DURING
SLEEP
To receive during Sleep, all the following conditions
must be met before entering Sleep mode:
RCSTA and TXSTA Control registers must be
configured for Synchronous Slave Reception (see
Section 25.4.2.4 “Synchronous Slave
Reception Set-up:”).
If interrupts are desired, set the RCIE bit of the
PIE1 register and the GIE and PEIE bits of the
INTCON register.
The RCIF interrupt flag must be cleared by read-
ing RCREG to unload any pending characters in
the receive buffer.
Upon entering Sleep mode, the device will be ready to
accept data and clocks on the RX/DT and TX/CK pins,
respectively. When the data word has been completely
clocked in by the external device, the RCIF interrupt
flag bit of the PIR1 register will be set. Thereby, waking
the processor from Sleep.
Upon waking from Sleep, the instruction following the
SLEEP instruction will be executed. If the Global Inter-
rupt Enable (GIE) bit of the INTCON register is also set,
then the Interrupt Service Routine at address 004h will
be called.
25.5.2 SYNCHRONOUS TRANSMIT
DURING SLEEP
To transmit during Sleep, all the following conditions
must be met before entering Sleep mode:
RCSTA and TXSTA Control registers must be
configured for Synchronous Slave Transmission
(see Section 25.4.2.2 “Synchronous Slave
Transmission Set-up:”).
The TXIF interrupt flag must be cleared by writing
the output data to the TXREG, thereby filling the
TSR and transmit buffer.
If interrupts are desired, set the TXIE bit of the
PIE1 register and the PEIE bit of the INTCON reg-
ister.
Interrupt enable bits TXIE of the PIE1 register and
PEIE of the INTCON register must set.
Upon entering Sleep mode, the device will be ready to
accept clocks on TX/CK pin and transmit data on the
RX/DT pin. When the data word in the TSR has been
completely clocked out by the external device, the
pending byte in the TXREG will transfer to the TSR and
the TXIF flag will be set. Thereby, waking the processor
from Sleep. At this point, the TXREG is available to
accept another character for transmission, which will
clear the TXIF flag.
Upon waking from Sleep, the instruction following the
SLEEP instruction will be executed. If the Global
Interrupt Enable (GIE) bit is also set then the Interrupt
Service Routine at address 0004h will be called.
2008-2011 Microchip Technology Inc. DS41364E-page 319
PIC16(L)F1934/6/7
26.0 CAPACITIVE SENSING (CPS)
MODULE
The Capacitive Sensing (CPS) module allows for an
interaction with an end user without a mechanical
interface. In a typical application, the CPS module is
attached to a pad on a Printed Circuit Board (PCB),
which is electrically isolated from the end user. When the
end user places their finger over the PCB pad, a
capacitive load is added, causing a frequency shift in the
CPS module. The CPS module requires software and at
least one timer resource to determine the change in
frequency. Key features of this module include:
Analog MUX for monitoring multiple inputs
Capacitive sensing oscillator
Multiple power ranges
Multiple timer resources
Software control
Operation during Sleep
FIGURE 26-1: CAPACITIVE SENSING BLOCK DIAGRAM
TMR0CS
CPS0
CPS1
CPS2
CPS3
CPS4
CPS5
CPS6
CPS7
CPS8(1)
CPS9(1)
CPS10(1)
CPSCH<3:0>(2)
Capacitive
Sensing
Oscillator
CPSOSC
CPSON
CPSRNG<1:0>
TMR0
0
1
Set
TMR0IF
Overflow
T0XCS
0
1
T0CKI
CPSOUT
CPS11(1)
CPS12(1)
CPS13(1)
CPS14(1)
CPS15(1)
CPSCLK
Note 1: Reference CPSCON1 register (Register 26-2) for channels implemented on each device.
2: CPSCH3 is not implemented on PIC16(L)F1936.
3: If CPSON = 0, disabling capacitive sensing, no channel is selected.
FOSC/4
Timer0 Module
CPSON(3)
T1CS<1:0>
T1OSC/
T1CKI
TMR1H:TMR1L
EN
T1GSEL<1:0>
Timer1 Gate
Control Logic
T1G
FOSC
FOSC/4
Timer1 Module
SYNCC1OUT
SYNCC2OUT
PIC16(L)F1934/6/7
DS41364E-page 320 2008-2011 Microchip Technology Inc.
26.1 Analog MUX
The CPS module can monitor up to 16 inputs. The
capacitive sensing inputs are defined as CPS<15:0>.
To determine if a frequency change has occurred the
user must:
Select the appropriate CPS pin by setting the
CPSCH<3:0> bits of the CPSCON1 register.
Set the corresponding ANSEL bit.
Set the corresponding TRIS bit.
Run the software algorithm.
Selection of the CPSx pin while the module is enabled
will cause the capacitive sensing oscillator to be on the
CPSx pin. Failure to set the corresponding ANSEL and
TRIS bits can cause the capacitive sensing oscillator to
stop, leading to false frequency readings.
26.2 Capacitive Sensing Oscillator
The capacitive sensing oscillator consists of a constant
current source and a constant current sink, to produce
a triangle waveform. The CPSOUT bit of the
CPSCON0 register shows the status of the capacitive
sensing oscillator, whether it is a sinking or sourcing
current. The oscillator is designed to drive a capacitive
load (single PCB pad) and at the same time, be a clock
source to either Timer0 or Timer1. The oscillator has
three different current settings as defined by
CPSRNG<1:0> of the CPSCON0 register. The different
current settings for the oscillator serve two purposes:
Maximize the number of counts in a timer for a
fixed time base.
Maximize the count differential in the timer during
a change in frequency.
26.3 Voltage References
The capacitive sensing oscillator uses voltage refer-
ences to provide two voltage thresholds for oscillation.
The upper voltage threshold is referred to as Ref+ and
the lower voltage threshold is referred to as Ref-.
The VSS voltage determines the lower threshold level
(Ref-) and the VDD voltage determines the upper
threshold level (Ref+).
26.4 Power Ranges
The capacitive sensing oscillator can operate in one of
three different power modes.
There are three distinct power ranges; low, medium and
high. Current consumption is dependent upon the range
selected. See Table 26-1 for proper power range
selection.
The remaining mode is a Noise Detection mode that
resides within the high range. The Noise Detection
mode is unique in that it disables the sinking and sourc-
ing of current on the analog pin but leaves the rest of
the oscillator circuitry active. This reduces the oscilla-
tion frequency on the analog pin to zero and also
greatly reduces the current consumed by the oscillator
module.
When noise is introduced onto the pin, the oscillator is
driven at the frequency determined by the noise. This
produces a detectable signal at the comparator output,
indicating the presence of activity on the pin.
Figure 26-2 shows a more detailed drawing of the
current sources and comparators associated with the
oscillator.
TABLE 26-1: POWER RANGE SELECTION
CPSRNG<1:0> Mode Nominal Current(1)
00 Off 0.0 A
01 Low 0.1 A
10 Medium 1.2 A
11 High 18 A
Note 1: See the applicable Electrical Specifica-
tions Chapter for more information.
2008-2011 Microchip Technology Inc. DS41364E-page 321
PIC16(L)F1934/6/7
26.5 Timer Resources
To measure the change in frequency of the capacitive
sensing oscillator, a fixed time base is required. For the
period of the fixed time base, the capacitive sensing
oscillator is used to clock either Timer0 or Timer1. The
frequency of the capacitive sensing oscillator is equal
to the number of counts in the timer divided by the
period of the fixed time base.
26.6 Fixed Time Base
To measure the frequency of the capacitive sensing
oscillator, a fixed time base is required. Any timer
resource or software loop can be used to establish the
fixed time base. It is up to the end user to determine the
method in which the fixed time base is generated.
26.6.1 TIMER0
To select Timer0 as the timer resource for the CPS
module:
Set the T0XCS bit of the CPSCON0 register.
Clear the TMR0CS bit of the OPTION_REG
register.
When Timer0 is chosen as the timer resource, the
capacitive sensing oscillator will be the clock source for
Timer0. Refer to Section 20.0 “Timer0 Module” for
additional information.
26.6.2 TIMER1
To select Timer1 as the timer resource for the CPS
module, set the TMR1CS<1:0> of the T1CON register
to ‘11’. When Timer1 is chosen as the timer resource,
the capacitive sensing oscillator will be the clock
source for Timer1. Because the Timer1 module has a
gate control, developing a time base for the frequency
measurement can be simplified by using the Timer0
overflow flag.
It is recommend that the Timer0 overflow flag, in con-
junction with the Toggle mode of the Timer1 gate, be
used to develop the fixed time base required by the
software portion of the CPS module. Refer to
Section 21.12 “Timer1 Gate Control Register” for
additional information.
TABLE 26-2: TIMER1 ENABLE FUNCTION
26.7 Software Control
The software portion of the CPS module is required to
determine the change in frequency of the capacitive
sensing oscillator. This is accomplished by the
following:
Setting a fixed time base to acquire counts on
Timer0 or Timer1.
Establishing the nominal frequency for the
capacitive sensing oscillator.
Establishing the reduced frequency for the
capacitive sensing oscillator due to an additional
capacitive load.
Set the frequency threshold.
26.7.1 NOMINAL FREQUENCY
(NO CAPACITIVE LOAD)
To determine the nominal frequency of the capacitive
sensing oscillator:
Remove any extra capacitive load on the selected
CPSx pin.
At the start of the fixed time base, clear the timer
resource.
At the end of the fixed time base save the value in
the timer resource.
The value of the timer resource is the number of
oscillations of the capacitive sensing oscillator for the
given time base. The frequency of the capacitive
sensing oscillator is equal to the number of counts on
in the timer divided by the period of the fixed time base.
26.7.2 REDUCED FREQUENCY
(ADDITIONAL CAPACITIVE LOAD)
The extra capacitive load will cause the frequency of the
capacitive sensing oscillator to decrease. To determine
the reduced frequency of the capacitive sensing
oscillator:
Add a typical capacitive load on the selected
CPSx pin.
Use the same fixed time base as the nominal
frequency measurement.
At the start of the fixed time base, clear the timer
resource.
At the end of the fixed time base save the value in
the timer resource.
The value of the timer resource is the number of oscil-
lations of the capacitive sensing oscillator with an addi-
tional capacitive load. The frequency of the capacitive
sensing oscillator is equal to the number of counts on
in the timer divided by the period of the fixed time base.
This frequency should be less than the value obtained
during the nominal frequency measurement.
Note: The fixed time base can not be generated
by the timer resource that the capacitive
sensing oscillator is clocking.
TMR1ON TMR1GE Timer1 Operation
00 Off
01 Off
10 On
11Count Enabled by input
PIC16(L)F1934/6/7
DS41364E-page 322 2008-2011 Microchip Technology Inc.
26.7.3 FREQUENCY THRESHOLD
The frequency threshold should be placed midway
between the value of nominal frequency and the
reduced frequency of the capacitive sensing oscillator.
Refer to Application Note AN1103, “Software Handling
for Capacitive Sensing” (DS01103) for more detailed
information on the software required for CPS module.
26.8 Operation during Sleep
The capacitive sensing oscillator will continue to run as
long as the module is enabled, independent of the part
being in Sleep. In order for the software to determine if
a frequency change has occurred, the part must be
awake. However, the part does not have to be awake
when the timer resource is acquiring counts.
Note: For more information on general capacitive
sensing refer to Application Notes:
AN1101, “Introduction to Capacitive
Sensing” (DS01101)
AN1102, “Layout and Physical
Design Guidelines for Capacitive
Sensing” (DS01102)
Note: Timer0 does not operate when in Sleep,
and therefore cannot be used for
capacitive sense measurements in Sleep.
2008-2011 Microchip Technology Inc. DS41364E-page 323
PIC16(L)F1934/6/7
REGISTER 26-1: CPSCON0: CAPACITIVE SENSING CONTROL REGISTER 0
R/W-0/0 R/W-0/0 U-0 U-0 R/W-0/0 R/W-0/0 R-0/0 R/W-0/0
CPSON CPSRNG<1:0> CPSOUT T0XCS
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7 CPSON: CPS Module Enable bit
1 = CPS module is enabled
0 = CPS module is disabled
bit 6-4 Unimplemented: Read as ‘0
bit 3-2 CPSRNG<1:0>: Capacitive Sensing Current Range
00 = Oscillator is off
01 = Oscillator is in Low Range. Charge/Discharge Current is nominally 0.1 µA
10 = Oscillator is in Medium Range. Charge/Discharge Current is nominally 1.2 µA
11 = Oscillator is in High Range. Charge/Discharge Current is nominally 18 µA
bit 1 CPSOUT: Capacitive Sensing Oscillator Status bit
1 = Oscillator is sourcing current (Current flowing out of the pin)
0 = Oscillator is sinking current (Current flowing into the pin)
bit 0 T0XCS: Timer0 External Clock Source Select bit
If TMR0CS = 1:
The T0XCS bit controls which clock external to the core/Timer0 module supplies Timer0:
1 = Timer0 clock source is the capacitive sensing oscillator
0 = Timer0 clock source is the T0CKI pin
If TMR0CS = 0:
Timer0 clock source is controlled by the core/Timer0 module and is FOSC/4
PIC16(L)F1934/6/7
DS41364E-page 324 2008-2011 Microchip Technology Inc.
REGISTER 26-2: CPSCON1: CAPACITIVE SENSING CONTROL REGISTER 1
U-0 U-0 U-0 U-0 R/W-0/0(1) R/W-0/0 R/W-0/0 R/W-0/0
CPSCH<3:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-4 Unimplemented: Read as ‘0
bit 3-0 CPSCH<3:0>: Capacitive Sensing Channel Select bits
If CPSON = 0:
These bits are ignored. No channel is selected.
If CPSON = 1:
0000 = channel 0, (CPS0)
0001 = channel 1, (CPS1)
0010 = channel 2, (CPS2)
0011 = channel 3, (CPS3)
0100 = channel 4, (CPS4)
0101 = channel 5, (CPS5)
0110 = channel 6, (CPS6)
0111 = channel 7, (CPS7)
1000 = channel 8, (CPS8(1))
1001 = channel 9, (CPS9(1))
1010 = channel 10, (CPS10(1))
1011 = channel 11, (CPS11(1))
1100 = channel 12, (CPS12(1))
1101 = channel 13, (CPS13(1))
1110 = channel 14, (CPS14(1))
1111 = channel 15, (CPS15(1))
Note 1: These channels are not implemented on the PIC16(L)F1936.
2: This bit is not implemented on PIC16(L)F1936, read as ‘0
2008-2011 Microchip Technology Inc. DS41364E-page 325
PIC16(L)F1934/6/7
TABLE 26-3: SUMMARY OF REGISTERS ASSOCIATED WITH CAPACITIVE SENSING
Name Bit 7 B it 6 B it 5 B it 4 B it 3 B it 2 Bit 1 Bit 0 Re giste r
on Page
ANSELA ANSA5 ANSA4 ANSA3 ANSA2 ANSA1 ANSA0 134
ANSELB ANSB5 ANSB4 ANSB3 ANSB2 ANSB1 ANSB0 139
ANSELD ANSD7 ANSD6 ANSD5 ANSD4 ANSD3 ANSD2 ANSD1 ANSD0 146
CPSCON0 CPSON —— CPSRNG<1:0> CPSOUT T0XCS 323
CPSCON1 ———— CPSCH<3:0> 324
OPTION_REG WPUEN INTEDG TMR0CS TMR0SE PSA PS2 PS1 PS0 193
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC —TMR1ON203
TRISA TRISA7 TRISA6 TRISA5 TRISA4 TRISA3 TRISA2 TRISA1 TRISA0 133
TRISB TRISB7 TRISB6 TRISB5 TRISB4 TRISB3 TRISB2 TRISB1 TRISB0 138
TRISD TRISD7 TRISD6 TRISD5 TRISD4 TRISD3 TRISD2 TRISD1 TRISD0 145
Legend: — = Unimplemented location, read as ‘0’. Shaded cells are not used by the CPS module.
PIC16(L)F1934/6/7
DS41364E-page 326 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 327
PIC16(L)F1934/6/7
27.0 LIQUID CRYSTAL DISPLAY
(LCD) DRIVER MODULE
The Liquid Crystal Display (LCD) Driver module
generates the timing control to drive a static or
multiplexed LCD panel. In the PIC16(L)F1934/6/7
device, the module drives the panels of up to four
commons and up to 24 segments. The LCD module
also provides control of the LCD pixel data.
The LCD Driver module supports:
Direct driving of LCD panel
Three LCD clock sources with selectable prescaler
Up to four common pins:
- Static (1 common)
- 1/2 multiplex (2 commons)
- 1/3 multiplex (3 commons)
- 1/4 multiplex (4 commons)
Segment pins up to:
- 16 (PIC16(L)F1936)
- 24 (PIC16(L)F1934/7)
Static, 1/2 or 1/3 LCD Bias
FIGURE 27-1: LCD DRIVER MODULE BLOCK DIAGRAM
Note: COM3 and SEG15 share the same physical
pin on the PIC16(L)F1936, therefore
SEG15 is not available when using 1/4
multiplex displays.
Data Bus SEG<23:0>(1, 3)
To I/O Pads(1)
LCDDATAx
Registers
Note 1: These are not directly connected to the I/O pads, but may be tri-stated, depending on the configuration of
the LCD module.
2: SEG<23:0> on PIC16F1934/1937, SEG<15:0> on PIC16(L)F1936.
3: COM3 and SEG15 share the same physical pin on the PIC16(L)F1936, therefore SEG15 is not available
when using 1/4 multiplex displays.
COM<3:0>(3)
Clock Source
Timing Control
Select and
Prescaler
LFINTOSC
FOSC/256
T1OSC
To I/O Pads(1)
LCDCON
LCDPS
LCDSEn
MUX
PIC16(L)F1934/6/7
DS41364E-page 328 2008-2011 Microchip Technology Inc.
27.1 LCD Registers
The module contains the following registers:
LCD Control register (LCDCON)
LCD Phase register (LCDPS)
LCD Reference Ladder register (LCDRL)
LCD Contrast Control register (LCDCST)
LCD Reference Voltage Control register
(LCDREF)
Up to 3 LCD Segment Enable registers (LCDSEn)
Up to 12 LCD data registers (LCDDATAn)
TABLE 27-1: LCD SEGMENT AND DATA
REGISTERS
The LCDCON register (Register 27-1) controls the
operation of the LCD driver module. The LCDPS regis-
ter (Register 27-2) configures the LCD clock source
prescaler and the type of waveform; Type-A or Type-B.
The LCDSEn registers (Register 27-5) configure the
functions of the port pins.
The following LCDSEn registers are available:
LCDSE0 SE<7:0>
LCDSE1 SE<15:8>
LCDSE2 SE<23:16>(1)
Once the module is initialized for the LCD panel, the
individual bits of the LCDDATAn registers are
cleared/set to represent a clear/dark pixel, respectively:
LCDDATA0 SEG<7:0>COM0
LCDDATA1 SEG<15:8>COM0
LCDDATA2 SEG<23:16>COM0(1)
LCDDATA3 SEG<7:0>COM1
LCDDATA4 SEG<15:8>COM1
LCDDATA5 SEG<23:16>COM1(1)
LCDDATA6 SEG<7:0>COM2
LCDDATA7 SEG<15:8>COM2
LCDDATA8 SEG<23:16>COM2(1)
LCDDATA9 SEG<7:0>COM3
LCDDATA10 SEG<15:8>COM3
LCDDATA11 SEG<23:16>COM3(1)
As an example, LCDDATAn is detailed in
Register 27-6.
Once the module is configured, the LCDEN bit of the
LCDCON register is used to enable or disable the LCD
module. The LCD panel can also operate during Sleep
by clearing the SLPEN bit of the LCDCON register.
Device # of LCD Registers
Segment
Enable Data
PIC16(L)F1936 2 8
PIC16(L)F1934/7 3 12
Note 1: PIC16(L)F1934/7 only.
Note 1: PIC16(L)F1934/7 only.
2008-2011 Microchip Technology Inc. DS41364E-page 329
PIC16(L)F1934/6/7
REGISTER 27-1: LCDCON: LIQUID CRYSTAL DISPLAY (LCD) CONTROL REGISTER
R/W-0/0 R/W-0/0 R/C-0/0 U-0 R/W-0/0 R/W-0/0 R/W-1/1 R/W-1/1
LCDEN SLPEN WERR CS<1:0> LMUX<1:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared C = Only clearable bit
bit 7 LCDEN: LCD Driver Enable bit
1 = LCD Driver module is enabled
0 = LCD Driver module is disabled
bit 6 SLPEN: LCD Driver Enable in Sleep Mode bit
1 = LCD Driver module is disabled in Sleep mode
0 = LCD Driver module is enabled in Sleep mode
bit 5 WERR: LCD Write Failed Error bit
1 = LCDDATAn register written while the WA bit of the LCDPS register = 0 (must be cleared in
software)
0 = No LCD write error
bit 4 Unimplemented: Read as ‘0
bit 3-2 CS<1:0>: Clock Source Select bits
00 = FOSC/256
01 = T1OSC (Timer1)
1x = LFINTOSC (31 kHz)
bit 1-0 LMUX<1:0>: Commons Select bits
Note 1: On these devices, COM3 and SEG15 are shared on one pin, limiting the device from driving 64 pixels.
LMUX<1:0> Multiplex
Maximum Number of Pixels
Bias
PIC16(L)F1936 PIC16(L)F1934/7
00 Static (COM0) 16 24 Static
01 1/2 (COM<1:0>) 32 48 1/2 or 1/3
10 1/3 (COM<2:0>) 48 72 1/2 or 1/3
11 1/4 (COM<3:0>) 60(1) 96 1/3
PIC16(L)F1934/6/7
DS41364E-page 330 2008-2011 Microchip Technology Inc.
REGISTER 27-2: LCDPS: LCD PHASE REGISTER
R/W-0/0 R/W-0/0 R-0/0 R-0/0 R/W-0/0 R/W-0/0 R/W-1/1 R/W-1/1
WFT BIASMD LCDA WA LP<3:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared C = Only clearable bit
bit 7 WFT: Waveform Type bit
1 = Type-B phase changes on each frame boundary
0 = Type-A phase changes within each common type
bit 6 BIASMD: Bias Mode Select bit
When LMUX<1:0> = 00:
0 = Static Bias mode (do not set this bit to1’)
When LMUX<1:0> = 01:
1 = 1/2 Bias mode
0 = 1/3 Bias mode
When LMUX<1:0> = 10:
1 = 1/2 Bias mode
0 = 1/3 Bias mode
When LMUX<1:0> = 11:
0 = 1/3 Bias mode (do not set this bit to ‘1’)
bit 5 LCDA: LCD Active Status bit
1 = LCD Driver module is active
0 = LCD Driver module is inactive
bit 4 WA: LCD Write Allow Status bit
1 = Writing to the LCDDATAn registers is allowed
0 = Writing to the LCDDATAn registers is not allowed
bit 3-0 LP<3:0>: LCD Prescaler Selection bits
1111 = 1:16
1110 = 1:15
1101 = 1:14
1100 = 1:13
1011 = 1:12
1010 = 1:11
1001 = 1:10
1000 = 1:9
0111 = 1:8
0110 = 1:7
0101 = 1:6
0100 = 1:5
0011 = 1:4
0010 = 1:3
0001 = 1:2
0000 = 1:1
2008-2011 Microchip Technology Inc. DS41364E-page 331
PIC16(L)F1934/6/7
REGISTER 27-3: LCDREF: LCD REFERENCE VOLTAGE CONTROL REGISTER
R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0 U-0
LCDIRE LCDIRS LCDIRI VLCD3PE VLCD2PE VLCD1PE
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared C = Only clearable bit
bit 7 LCDIRE: LCD Internal Reference Enable bit
1 = Internal LCD Reference is enabled and connected to the Internal Contrast Control circuit
0 = Internal LCD Reference is disabled
bit 6 LCDIRS: LCD Internal Reference Source bit
If LCDIRE = 1:
0 = Internal LCD Contrast Control is powered by VDD
1 = Internal LCD Contrast Control is powered by a 3.072V output of the FVR
If LCDIRE = 0:
Internal LCD Contrast Control is unconnected. LCD bandgap buffer is disabled.
bit 5 LCDIRI: LCD Internal Reference Ladder Idle Enable bit
Allows the Internal FVR buffer to shut down when the LCD Reference Ladder is in power mode ‘B’
1 = When the LCD Reference Ladder is in power mode ‘B’, the LCD Internal FVR buffer is disabled
0 = The LCD Internal FVR Buffer ignores the LCD Reference Ladder Power mode
bit 4 Unimplemented: Read as ‘0
bit 3 VLCD3PE: VLCD3 Pin Enable bit
1 = The VLCD3 pin is connected to the internal bias voltage LCDBIAS3(1)
0 = The VLCD3 pin is not connected
bit 2 VLCD2PE: VLCD2 Pin Enable bit
1 = The VLCD2 pin is connected to the internal bias voltage LCDBIAS2(1)
0 = The VLCD2 pin is not connected
bit 1 VLCD1PE: VLCD1 Pin Enable bit
1 = The VLCD1 pin is connected to the internal bias voltage LCDBIAS1(1)
0 = The VLCD1 pin is not connected
bit 0 Unimplemented: Read as ‘0
Note 1: Normal pin controls of TRISx and ANSELx are unaffected.
PIC16(L)F1934/6/7
DS41364E-page 332 2008-2011 Microchip Technology Inc.
REGISTER 27-4: LCDCST: LCD CONTRAST CONTROL REGISTER
U-0 U-0 U-0 U-0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
LCDCST<2:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared C = Only clearable bit
bit 7-3 Unimplemented: Read as ‘0
bit 2-0 LCDCST<2:0>: LCD Contrast Control bits
Selects the resistance of the LCD contrast control resistor ladder
Bit Value = Resistor ladder
000 = Minimum Resistance (Maximum contrast). Resistor ladder is shorted.
001 = Resistor ladder is at 1/7th of maximum resistance
010 = Resistor ladder is at 2/7th of maximum resistance
011 = Resistor ladder is at 3/7th of maximum resistance
100 = Resistor ladder is at 4/7th of maximum resistance
101 = Resistor ladder is at 5/7th of maximum resistance
110 = Resistor ladder is at 6/7th of maximum resistance
111 = Resistor ladder is at maximum resistance (Minimum contrast).
2008-2011 Microchip Technology Inc. DS41364E-page 333
PIC16(L)F1934/6/7
REGISTER 27-5: LCDSEn: LCD SEGMENT ENABLE REGISTERS
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0
SEn SEn SEn SEn SEn SEn SEn SEn
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 SEn: Segment Enable bits
1 = Segment function of the pin is enabled
0 = I/O function of the pin is enabled
REGISTER 27-6: LCDDATAn: LCD DATA REGISTERS
R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u R/W-x/u
SEGx-COMy SEGx-COMy SEGx-COMy SEGx-COMy SEGx-COMy SEGx-COMy SEGx-COMy SEGx-COMy
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-0 SEGx-COMy: Pixel On bits
1 = Pixel on (dark)
0 = Pixel off (clear)
PIC16(L)F1934/6/7
DS41364E-page 334 2008-2011 Microchip Technology Inc.
27.2 LCD Clock Source Selection
The LCD module has 3 possible clock sources:
•F
OSC/256
•T1OSC
•LFINTOSC
The first clock source is the system clock divided by
256 (FOSC/256). This divider ratio is chosen to provide
about 1 kHz output when the system clock is 8 MHz.
The divider is not programmable. Instead, the LCD
prescaler bits LP<3:0> of the LCDPS register are used
to set the LCD frame clock rate.
The second clock source is the T1OSC. This also gives
about 1 kHz when a 32.768 kHz crystal is used with the
Timer1 oscillator. To use the Timer1 oscillator as a
clock source, the T1OSCEN bit of the T1CON register
should be set.
The third clock source is the 31 kHz LFINTOSC, which
provides approximately 1 kHz output.
The second and third clock sources may be used to
continue running the LCD while the processor is in
Sleep.
Using bits CS<1:0> of the LCDCON register can select
any of these clock sources.
27.2.1 LCD PRESCALER
A 4-bit counter is available as a prescaler for the LCD
clock. The prescaler is not directly readable or writable;
its value is set by the LP<3:0> bits of the LCDPS register,
which determine the prescaler assignment and prescale
ratio.
The prescale values are selectable from 1:1 through
1:16.
FIGURE 27-2: LCD CLOCK GENERATION
CS<1:0>
T1OSC 32 kHz
Crystal Osc.
LFINTOSC
Nominal = 31 kHz
Static
1/2
1/3,
1/4
÷4
LMUX<1:0>
4-bit Prog ÷1, 2, 3, 4
Ring Counter
COM0
COM1
COM2
COM3
÷256
FOSC
÷2 ÷ 32
LP<3:0>
Prescaler
To Ladder
Power Control
Segment
Clock
Counter
2008-2011 Microchip Technology Inc. DS41364E-page 335
PIC16(L)F1934/6/7
27.3 LCD Bias Voltage Generat ion
The LCD module can be configured for one of three
bias types:
Static Bias (2 voltage levels: VSS and VLCD)
1/2 Bias (3 voltage levels: VSS, 1/2 VLCD and
VLCD)
1/3 Bias (4 voltage levels: VSS, 1/3 VLCD,
2/3 VLCD and VLCD)
TABLE 27-2: LCD BIAS VOLTAGES
So that the user is not forced to place external compo-
nents and use up to three pins for bias voltage generation,
internal contrast control and an internal reference ladder
are provided internally. Both of these features may be
used in conjunction with the external VLCD<3:1> pins, to
provide maximum flexibility. Refer to Figure 27-3.
FIGURE 27-3: LCD BIAS VOLTAGE GENERATION BLOCK DIAGRAM
St atic Bias 1/2 Bias 1/3 Bias
LCD Bias 0 VSS VSS VSS
LCD Bias 1 —1/2 VDD 1/3 VDD
LCD Bias 2 —1/2 VDD 2/3 VDD
LCD Bias 3 VLCD3VLCD3VLCD3
VDD LCDIRE
x 3 3.072V
1.024V from
FVR
VLCD3
LCDIRS
LCDIRE
LCDIRS
LCDCST<2:0>
VLCD3PE
VLCD2
VLCD2PE
VLCD1
VLCD1PE
LCDRLP1
BIASMD
lcdbias3
lcdbias2
lcdbias1
lcdbias0
LCDA
LCDA
LCDA
LCDRLP0
PIC16(L)F1934/6/7
DS41364E-page 336 2008-2011 Microchip Technology Inc.
27.4 LCD Bias Internal Reference
Ladder
The internal reference ladder can be used to divide the
LCD bias voltage two or three equally spaced voltages
that will be supplied to the LCD segment pins. To create
this, the reference ladder consists of three matched
resistors. Refer to Figure 27-3.
27.4.1 BIAS MODE INTERACTION
When in 1/2 Bias mode (BIASMD = 1), then the middle
resistor of the ladder is shorted out so that only two
voltages are generated. The current consumption of the
ladder is higher in this mode, with the one resistor
removed.
TABLE 27-3: LCD INTERNAL LADDER
POWER MODES (1/3 BIAS)
27.4.2 POWER MODES
The internal reference ladder may be operated in one of
three power modes. This allows the user to trade off LCD
contrast for power in the specific application. The larger
the LCD glass, the more capacitance is present on a
physical LCD segment, requiring more current to
maintain the same contrast level.
Three different power modes are available, LP, MP and
HP. The internal reference ladder can also be turned off
for applications that wish to provide an external ladder
or to minimize power consumption. Disabling the
internal reference ladder results in all of the ladders
being disconnected, allowing external voltages to be
supplied.
Whenever the LCD module is inactive (LCDA = 0), the
internal reference ladder will be turned off.
Power
Mode Nominal Resistance of
Entire Ladder Nominal
IDD
Low 3 Mohm 1 µA
Medium 300 kohm 10 µA
High 30 kohm 100 µA
2008-2011 Microchip Technology Inc. DS41364E-page 337
PIC16(L)F1934/6/7
27.4.3 AUTOMATIC POWER MODE
SWITCHING
As an LCD segment is electrically only a capacitor, cur-
rent is drawn only during the interval where the voltage
is switching. To minimize total device current, the LCD
internal reference ladder can be operated in a different
power mode for the transition portion of the duration.
This is controlled by the LCDRL register
(Register 27-7).
The LCDRL register allows switching between two
power modes, designated ‘A’ and ‘B’. ‘A’ Power mode
is active for a programmable time, beginning at the
time when the LCD segments transition. ‘B’ Power
mode is the remaining time before the segments or
commons change again. The LRLAT<2:0> bits select
how long, if any, that the ‘A’ Power mode is active.
Refer to Figure 27-4.
To implement this, the 5-bit prescaler used to divide
the 32 kHz clock down to the LCD controller’s 1 kHz
base rate is used to select the power mode.
FIGURE 27-4: LCD INTERNAL REFERENCE LADDER POWER MODE SWITCHING DIAGRAM –
TYPE A
Single Segment Time
‘H00 ‘H01 ‘H02 ‘H03 ‘H04 ‘H05 ‘H06 ‘H07 ‘H0E ‘H0F ‘H00 ‘H01
‘H3
Power Mode A Power Mode B Mode A
LRLAT<2:0>
32 kHz Clock
Ladder Power
Segment Clock
LRLAT<2:0>
Segment Data
Power Mode
COM0
SEG0
COM0-SEG0
Control
V0
V1
V0
V1
V0
V1
-V1
PIC16(L)F1934/6/7
DS41364E-page 338 Preliminary 2008-2011 Microchip Technology Inc.
FIGURE 27-5: LCD INTERNAL REFERENCE LADDER POWER MODE SWITCHING DIAGRAM – TYPE A W AVEFORM (1/2 MUX, 1/ 2 BIAS DRIVE)
Single Segment Time
‘H00 ‘H01 ‘H02 ‘H03 ‘H04 ‘H05 ‘H06 ‘H07 ‘H0F
Power Mode A Power Mode B
LRLAT<2:0> = 011
32 kHz Clock
Ladder Power
Segment Clock
Segment Data
Power Mode
COM0-SEG0
Control
V1
V2
V0
-V2
-V1
Single Segment Time
‘H00 ‘H01 ‘H02 ‘H03 ‘H04 ‘H05 ‘H06 ‘H07 ‘H0F
Power Mode A Power Mode B
‘H0E ‘H0E
LRLAT<2:0> = 011
2008-2011 Microchip Technology Inc. Preliminary DS41364E-page 339
PIC16(L)F1934/6/7
FIGURE 27-6: LCD INTERNAL REFERENCE LADDER POWER MODE SWITCHING DIAGRAM – TYPE B W AVEFORM (1/2 MUX, 1/ 2 BIAS DRIVE)
Single Segment Time
‘H00 ‘H01 ‘H02 ‘H03 ‘H0F
Power Mode A Power Mode B
32 kHz Clock
Ladder Power
Segment Clock
Segment Data
Power Mode
COM0-SEG0
Control
V1
V2
V0
-V2
-V1
‘H0E
Single Segment Time
‘H10 ‘H11 ‘H12 ‘H13 ‘H1F
Power Mode A Power Mode B
‘H1E
Single Segment Time
‘H00 ‘H01 ‘H02 ‘H03 ‘H0F
Power Mode A Power Mode B
‘H0E
Single Segment Time
‘H10 ‘H11 ‘H12 ‘H13 ‘H1F
Power Mode A Power Mode B
‘H1E
LRLAT<2:0>
=
011
LRLAT<2:0>
=
011
LRLAT<2:0>
=
011
LRLAT<2:0>
=
011
PIC16(L)F1934/6/7
DS41364E-page 340 2008-2011 Microchip Technology Inc.
REGISTER 27-7: LCDRL: LCD REFERENCE LADDER CONTROL REGISTERS
R/W-0/0 R/W-0/0 R/W-0/0 R/W-0/0 U-0 R/W-0/0 R/W-0/0 R/W-0/0
LRLAP<1:0> LRLBP<1:0> LRLAT<2:0>
bit 7 bit 0
Legend:
R = Readable bit W = Writable bit U = Unimplemented bit, read as ‘0’
u = Bit is unchanged x = Bit is unknown -n/n = Value at POR and BOR/Value at all other Resets
‘1’ = Bit is set ‘0’ = Bit is cleared
bit 7-6 LRLAP<1:0>: LCD Reference Ladder A Time Power Control bits
During Time interval A (Refer to Figure 27-4):
00 = Internal LCD Reference Ladder is powered down and unconnected
01 = Internal LCD Reference Ladder is powered in Low-Power mode
10 = Internal LCD Reference Ladder is powered in Medium-Power mode
11 = Internal LCD Reference Ladder is powered in High-Power mode
bit 5-4 LRLBP<1:0>: LCD Reference Ladder B Time Power Control bits
During Time interval B (Refer to Figure 27-4):
00 = Internal LCD Reference Ladder is powered down and unconnected
01 = Internal LCD Reference Ladder is powered in Low-Power mode
10 = Internal LCD Reference Ladder is powered in Medium-Power mode
11 = Internal LCD Reference Ladder is powered in High-Power mode
bit 3 Unimplemented: Read as ‘0
bit 2-0 LRLAT<2:0>: LCD Reference Ladder A Time Interval Control bits
Sets the number of 32 kHz clocks that the A Time Interval Power mode is active
For type A waveforms (WFT =
0
):
000 = Internal LCD Reference Ladder is always in ‘B’ Power mode
001 = Internal LCD Reference Ladder is in ‘A’ Power mode for 1 clock and ‘B’ Power mode for 15 clocks
010 = Internal LCD Reference Ladder is in ‘A’ Power mode for 2 clocks and ‘B’ Power mode for 14 clocks
011 = Internal LCD Reference Ladder is in ‘A’ Power mode for 3 clocks and ‘B’ Power mode for 13 clocks
100 = Internal LCD Reference Ladder is in ‘A’ Power mode for 4 clocks and ‘B’ Power mode for 12 clocks
101 = Internal LCD Reference Ladder is in ‘A’ Power mode for 5 clocks and ‘B’ Power mode for 11 clocks
110 = Internal LCD Reference Ladder is in ‘A’ Power mode for 6 clocks and ‘B’ Power mode for 10 clocks
111 = Internal LCD Reference Ladder is in ‘A’ Power mode for 7 clocks and ‘B’ Power mode for 9 clocks
For type B waveforms (WFT =
1
):
000
=
Internal LCD Reference Ladder is always in ‘B’ Power mode.
001 = Internal LCD Reference Ladder is in ‘A’ Power mode for 1 clock and ‘B’ Power mode for 31 clocks
010 = Internal LCD Reference Ladder is in ‘A’ Power mode for 2 clocks and ‘B’ Power mode for 30 clocks
011 = Internal LCD Reference Ladder is in ‘A’ Power mode for 3 clocks and ‘B’ Power mode for 29 clocks
100 = Internal LCD Reference Ladder is in ‘A’ Power mode for 4 clocks and ‘B’ Power mode for 28 clocks
101 = Internal LCD Reference Ladder is in ‘A’ Power mode for 5 clocks and ‘B’ Power mode for 27 clocks
110 = Internal LCD Reference Ladder is in ‘A’ Power mode for 6 clocks and ‘B’ Power mode for 26 clocks
111 = Internal LCD Reference Ladder is in ‘A’ Power mode for 7 clocks and ‘B’ Power mode for 25 clocks
2008-2011 Microchip Technology Inc. DS41364E-page 341
PIC16(L)F1934/6/7
27.4.4 CONTRAST CONTROL
The LCD contrast control circuit consists of a
seven-tap resistor ladder, controlled by the LCDCST
bits. Refer to Figure 27-7.
The contrast control circuit is used to decrease the
output voltage of the signal source by a total of
approximately 10%, when LCDCST = 111.
Whenever the LCD module is inactive (LCDA = 0), the
contrast control ladder will be turned off (open).
FIGURE 27-7: INTERNAL REFERENCE AND CONTRAST CONTROL BLOCK DIAGRAM
27.4.5 INTERNAL REFERENCE
Under firmware control, an internal reference for the
LCD bias voltages can be enabled. When enabled, the
source of this voltage can be either VDDIO or a voltage
3 times the main fixed voltage reference (3.072V).
When no internal reference is selected, the LCD con-
trast control circuit is disabled and LCD bias must be
provided externally.
Whenever the LCD module is inactive (LCDA = 0), the
internal reference will be turned off.
When the internal reference is enabled and the Fixed
Voltage Reference is selected, the LCDIRI bit can be
used to minimize power consumption by tieing into the
LCD Reference Ladder Automatic Power mode switch-
ing. When LCDIRI = 1 and the LCD reference ladder is
in Power mode ‘B’, the LCD internal FVR buffer is
disabled.
.
27.4.6 VLCD<3:1> PINS
The VLCD<3:1> pins provide the ability for an external
LCD bias network to be used instead of the internal lad-
der. Use of the VLCD<3:1> pins does not prevent use
of the internal ladder. Each VLCD pin has an indepen-
dent control in the LCDREF register (Register 27-3),
allowing access to any or all of the LCD Bias signals.
This architecture allows for maximum flexibility in differ-
ent applications
For example, the VLCD<3:1> pins may be used to add
capacitors to the internal reference ladder, increasing
the drive capacity.
For applications where the internal contrast control is
insufficient, the firmware can choose to only enable the
VLCD3 pin, allowing an external contrast control circuit
to use the internal reference divider.
LCDCST<2:0>
Analog
RR RR
7 Stages
MUX
To top of
Reference Ladder
7
0
3
3.072V
VDDIO
From FVR
Buffer
Internal Reference Contrast control
Note: The LCD module automatically turns on the
Fixed Voltage Reference when needed.
PIC16(L)F1934/6/7
DS41364E-page 342 2008-2011 Microchip Technology Inc.
27.5 LCD Multiplex Types
The LCD driver module can be configured into one of
four multiplex types:
Static (only COM0 is used)
1/2 multiplex (COM<1:0> are used)
1/3 multiplex (COM<2:0> are used)
1/4 multiplex (COM<3:0> are used)
The LMUX<1:0> bit setting of the LCDCON register
decides which of the LCD common pins are used (see
Table 27-4 for details).
If the pin is a digital I/O, the corresponding TRIS bit
controls the data direction. If the pin is a COM drive,
then the TRIS setting of that pin is overridden.
TABLE 27-4: COMMON PIN USAGE
27.6 Segment Enables
The LCDSEn registers are used to select the pin
function for each segment pin. The selection allows
each pin to operate as either an LCD segment driver or
as one of the pin’s alternate functions. To configure the
pin as a segment pin, the corresponding bits in the
LCDSEn registers must be set to1’.
If the pin is a digital I/O, the corresponding TRIS bit
controls the data direction. Any bit set in the LCDSEn
registers overrides any bit settings in the corresponding
TRIS register.
27.7 Pixel Control
The LCDDATAx registers contain bits which define the
state of each pixel. Each bit defines one unique pixel.
Register 27-6 shows the correlation of each bit in the
LCDDATAx registers to the respective common and
segment signals.
Any LCD pixel location not being used for display can
be used as general purpose RAM.
27.8 LCD Frame Frequency
The rate at which the COM and SEG outputs change is
called the LCD frame frequency.
TABLE 27-5: FRAME FREQUENCY
FORMULAS
TABLE 27-6: APPROXIMATE FRAME
FREQUENCY (IN Hz) USING
FOSC @ 8 MHz, TIMER1 @
32.768 kHz OR LFINTOSC
Multiplex LMUX
<1:0> COM3 COM2 COM1
Static 00 Unused Unused Unused
1/2 01 Unused Unused Active
1/3 10 Unused Active Active
1/4 11 Active Active Active
Note: On a Power-on Reset, these pins are
configured as normal I/O, not LCD pins.
Multiplex Frame Frequency =
Static Clock source/(4 x 1 x (LPD Prescaler) x 32))
1/2 Clock source/(2 x 2 x (LPD Prescaler) x 32))
1/3 Clock source/(1 x 3 x (LPD Prescaler) x 32))
1/4 Clock source/(1 x 4 x (LPD Prescaler) x 32))
Note: Clock source is FOSC/256, T1OSC or
LFINTOSC.
LP<3:0> Static 1/2 1/3 1/4
2 122 122 162 122
3 81 81 108 81
461618161
549496549
641415441
735354735
2008-2011 Microchip Technology Inc. DS41364E-page 343
PIC16(L)F1934/6/7
TABLE 27-7: LCD SEGMENT MAPPING WORKSHEET
LCD
Function COM0 COM1 COM2 COM3
LCDDATAx
Address LCD
Segment LCDDATAx
Address LCD
Segment LCDDATAx
Address LCD
Segment LCDDATAx
Address LCD
Segment
SEG0 LCDDATA0, 0 LCDDATA3, 0 LCDDATA6, 0 LCDDATA9, 0
SEG1 LCDDATA0, 1 LCDDATA3, 1 LCDDATA6, 1 LCDDATA9, 1
SEG2 LCDDATA0, 2 LCDDATA3, 2 LCDDATA6, 2 LCDDATA9, 2
SEG3 LCDDATA0, 3 LCDDATA3, 3 LCDDATA6, 3 LCDDATA9, 3
SEG4 LCDDATA0, 4 LCDDATA3, 4 LCDDATA6, 4 LCDDATA9, 4
SEG5 LCDDATA0, 5 LCDDATA3, 5 LCDDATA6, 5 LCDDATA9, 5
SEG6 LCDDATA0, 6 LCDDATA3, 6 LCDDATA6, 6 LCDDATA9, 6
SEG7 LCDDATA0, 7 LCDDATA3, 7 LCDDATA6, 7 LCDDATA9, 7
SEG8 LCDDATA1, 0 LCDDATA4, 0 LCDDATA7, 0 LCDDATA10, 0
SEG9 LCDDATA1, 1 LCDDATA4, 1 LCDDATA7, 1 LCDDATA10, 1
SEG10 LCDDATA1, 2 LCDDATA4, 2 LCDDATA7, 2 LCDDATA10, 2
SEG11 LCDDATA1, 3 LCDDATA4, 3 LCDDATA7, 3 LCDDATA10, 3
SEG12 LCDDATA1, 4 LCDDATA4, 4 LCDDATA7, 4 LCDDATA10, 4
SEG13 LCDDATA1, 5 LCDDATA4, 5 LCDDATA7, 5 LCDDATA10, 5
SEG14 LCDDATA1, 6 LCDDATA4, 6 LCDDATA7, 6 LCDDATA10, 6
SEG15 LCDDATA1, 7 LCDDATA4, 7 LCDDATA7, 7 LCDDATA10, 7
SEG16 LCDDATA2, 0 LCDDATA5, 0 LCDDATA8, 0 LCDDATA11, 0
SEG17 LCDDATA2, 1 LCDDATA5, 1 LCDDATA8, 1 LCDDATA11, 1
SEG18 LCDDATA2, 2 LCDDATA5, 2 LCDDATA8, 2 LCDDATA11, 2
SEG19 LCDDATA2, 3 LCDDATA5, 3 LCDDATA8, 3 LCDDATA11, 3
SEG20 LCDDATA2, 4 LCDDATA5, 4 LCDDATA8, 4 LCDDATA11, 4
SEG21 LCDDATA2, 5 LCDDATA5, 5 LCDDATA8, 5 LCDDATA11, 5
SEG22 LCDDATA2, 6 LCDDATA5, 6 LCDDATA8, 6 LCDDATA11, 6
SEG23 LCDDATA2, 7 LCDDATA5, 7 LCDDATA8, 7 LCDDATA11, 7
PIC16(L)F1934/6/7
DS41364E-page 344 2008-2011 Microchip Technology Inc.
27.9 LCD Wavefor m Generation
LCD waveforms are generated so that the net AC
voltage across the dark pixel should be maximized and
the net AC voltage across the clear pixel should be
minimized. The net DC voltage across any pixel should
be zero.
The COM signal represents the time slice for each
common, while the SEG contains the pixel data.
The pixel signal (COM-SEG) will have no DC
component and it can take only one of the two RMS
values. The higher RMS value will create a dark pixel
and a lower RMS value will create a clear pixel.
As the number of commons increases, the delta
between the two RMS values decreases. The delta
represents the maximum contrast that the display can
have.
The LCDs can be driven by two types of waveform:
Type-A and Type-B. In Type-A waveform, the phase
changes within each common type, whereas in Type-B
waveform, the phase changes on each frame
boundary. Thus, Type-A waveform maintains 0 VDC
over a single frame, whereas Type-B waveform takes
two frames.
Figure 27-8 through Figure 27-18 provide waveforms
for static, half-multiplex, 1/3-multiplex and 1/4-multiplex
drives for Type-A and Type-B waveforms.
FIGURE 27-8: TYPE-A/TYPE-B WAVEFORMS IN STATIC DRIVE
Note 1: If Sleep has to be executed with LCD
Sleep disabled (LCDCON<SLPEN> is
1’), then care must be taken to execute
Sleep only when VDC on all the pixels is
0’.
2: When the LCD clock source is FOSC/256,
if Sleep is executed, irrespective of the
LCDCON<SLPEN> setting, the LCD
immediately goes into Sleep. Thus, take
care to see that VDC on all pixels is ‘0
when Sleep is executed.
V1
V0
COM0 pin
SEG0 pin
COM0-SEG0
COM0-SEG1
SEG1 pin
V1
V0
V1
V0
V0
V1
-V1
V0
1 Frame
COM0
SEG0
SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
segment voltage
(active)
segment voltage
(inactive)
2008-2011 Microchip Technology Inc. DS41364E-page 345
PIC16(L)F1934/6/7
FIGURE 27-9: TYPE-A WAVEFORMS IN 1/2 MUX, 1/2 BIAS DRIVE
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
-V2
-V1
V2
V1
V0
-V2
-V1
COM0 pin
COM1 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
1 Frame
COM1
COM0
SEG0
SEG1
SEG2
SEG3
1 Segment Time
Note: 1 Frame = 2 single segment times.
segment voltage
segment voltage
(active)
(inactive)
PIC16(L)F1934/6/7
DS41364E-page 346 2008-2011 Microchip Technology Inc.
FIGURE 27-10 : TYPE-B WAVEFORMS IN 1/2 MUX, 1/2 BIAS DRIVE
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
-V2
-V1
V2
V1
V0
-V2
-V1
COM0 pin
COM1 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
COM1
COM0
SEG2
SEG3
2 Frames
Note: 1 Frame = 2 single segment times.
1 Segment Time
segment voltage
(active)
segment voltage
(inactive)
SEG0
SEG1
2008-2011 Microchip Technology Inc. DS41364E-page 347
PIC16(L)F1934/6/7
FIGURE 27-11: TYP E-A WAVEFORMS IN 1/2 MUX, 1/3 BIAS DRIVE
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
-V3
-V2
-V1
V3
V2
V1
V0
-V3
-V2
-V1
COM0 pin
COM1 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
1 Frame
COM1
COM0
SEG2
SEG3
segment voltage
(active)
segment voltage
(inactive)
SEG0
SEG1
1 Segment Time
Note: 1 Frame = 2 single segment times.
PIC16(L)F1934/6/7
DS41364E-page 348 2008-2011 Microchip Technology Inc.
FIGURE 27-12 : TYPE-B WAVEFORMS IN 1/2 MUX, 1/3 BIAS DRIVE
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
-V3
-V2
-V1
V3
V2
V1
V0
-V3
-V2
-V1
COM0 pin
COM1 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
COM1
COM0
SEG2
SEG3
segment voltage
(active)
segment voltage
(inactive)
SEG0
SEG1
2 Frames
Note: 1 Frame = 2 single segment times.
1 Segment Time
2008-2011 Microchip Technology Inc. DS41364E-page 349
PIC16(L)F1934/6/7
FIGURE 27-13 : TYPE-A WAVEFORMS IN 1/3 MUX, 1/2 BIAS DRIVE
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
-V2
-V1
V2
V1
V0
-V2
-V1
COM0 pin
COM1 pin
COM2 pin
SEG0 and
SEG1 pin
COM0-SEG0
COM0-SEG1
COM2
COM1
COM0
SEG0
SEG1
SEG2
SEG2 pins
segment voltage
(inactive)
segment voltage
(active)
1 Frame
1 Segment Time
Note: 1 Frame = 2 single segment times.
PIC16(L)F1934/6/7
DS41364E-page 350 2008-2011 Microchip Technology Inc.
FIGURE 27-14 : TYPE-B WAVEFORMS IN 1/3 MUX, 1/2 BIAS DRIVE
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
V2
V1
V0
-V2
-V1
V2
V1
V0
-V2
-V1
COM0 pin
COM1 pin
COM2 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
COM2
COM1
COM0
SEG0
SEG1
SEG2
segment voltage
(inactive)
segment voltage
(active)
2 Frames
Note: 1 Frame = 2 single segment times.
1 Segment Time
2008-2011 Microchip Technology Inc. DS41364E-page 351
PIC16(L)F1934/6/7
FIGURE 27-15 : TYPE-A WAVEFORMS IN 1/3 MUX, 1/3 BIAS DRIVE
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
-V3
-V2
-V1
V3
V2
V1
V0
-V3
-V2
-V1
COM0 pin
COM1 pin
COM2 pin
SEG0 and
SEG1 pin
COM0-SEG0
COM0-SEG1
COM2
COM1
COM0
SEG0
SEG1
SEG2
SEG2 pins
segment voltage
(inactive)
segment voltage
(active)
1 Frame
1 Segment Time
Note: 1 Frame = 2 single segment times.
PIC16(L)F1934/6/7
DS41364E-page 352 2008-2011 Microchip Technology Inc.
FIGURE 27-16 : TYPE-B WAVEFORMS IN 1/3 MUX, 1/3 BIAS DRIVE
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
-V3
-V2
-V1
V3
V2
V1
V0
-V3
-V2
-V1
COM0 pin
COM1 pin
COM2 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
COM2
COM1
COM0
SEG0
SEG1
SEG2
segment voltage
(inactive)
segment voltage
(active)
2 Frames
Note: 1 Frame = 2 single segment times.
1 Segment Time
2008-2011 Microchip Technology Inc. DS41364E-page 353
PIC16(L)F1934/6/7
FIGURE 27-17 : TYPE-A WAVEFORMS IN 1/4 MUX, 1/3 BIAS DRIVE
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
-V3
-V2
-V1
V3
V2
V1
V0
-V3
-V2
-V1
COM0 pin
COM1 pin
COM2 pin
COM3 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
COM3
COM2
COM1
COM0
SEG0
SEG1
segment voltage
(active)
segment voltage
(inactive)
1 Frame
1 Segment Time
Note: 1 Frame = 2 single segment times.
PIC16(L)F1934/6/7
DS41364E-page 354 2008-2011 Microchip Technology Inc.
FIGURE 27-18 : TYPE-B WAVEFORMS IN 1/4 MUX, 1/3 BIAS DRIVE
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
-V3
-V2
-V1
V3
V2
V1
V0
-V3
-V2
-V1
COM0 pin
COM1 pin
COM2 pin
COM3 pin
SEG0 pin
SEG1 pin
COM0-SEG0
COM0-SEG1
COM2
COM1
COM0
SEG0
SEG1
COM3
segment voltage
(active)
segment voltage
(inactive) 2 Frames
Note: 1 Frame = 2 single segment times.
1 Segment Time
2008-2011 Microchip Technology Inc. DS41364E-page 355
PIC16(L)F1934/6/7
27.10 LCD Interrupts
The LCD module provides an interrupt in two cases. An
interrupt when the LCD controller goes from active to
inactive controller. An interrupt also provides unframed
boundaries for Type B waveform. The LCD timing gen-
eration provides an interrupt that defines the LCD
frame timing.
27.10.1 LCD INTERRUPT ON MODULE
SHUTDOWN
An LCD interrupt is generated when the module com-
pletes shutting down (LCDA goes from ‘1’ to ‘0’).
27.10.2 LCD FRAME INTERRUPTS
A new frame is defined to begin at the leading edge of
the COM0 common signal. The interrupt will be set
immediately after the LCD controller completes access-
ing all pixel data required for a frame. This will occur at
a fixed interval before the frame boundary (TFINT), as
shown in Figure 27-19. The LCD controller will begin to
access data for the next frame within the interval from
the interrupt to when the controller begins to access
data after the interrupt (TFWR). New data must be writ-
ten within TFWR, as this is when the LCD controller will
begin to access the data for the next frame.
When the LCD driver is running with Type-B waveforms
and the LMUX<1:0> bits are not equal to ‘00’ (static
drive), there are some additional issues that must be
addressed. Since the DC voltage on the pixel takes two
frames to maintain zero volts, the pixel data must not
change between subsequent frames. If the pixel data
were allowed to change, the waveform for the odd
frames would not necessarily be the complement of the
waveform generated in the even frames and a DC
component would be introduced into the panel.
Therefore, when using Type-B waveforms, the user
must synchronize the LCD pixel updates to occur within
a subframe after the frame interrupt.
To correctly sequence writing while in Type-B, the
interrupt will only occur on complete phase intervals. If
the user attempts to write when the write is disabled,
the WERR bit of the LCDCON register is set and the
write does not occur.
Note: The LCD frame interrupt is not generated
when the Type-A waveform is selected
and when the Type-B with no multiplex
(static) is selected.
PIC16(L)F1934/6/7
DS41364E-page 356 2008-2011 Microchip Technology Inc.
FIGURE 27-19: WAVEFORMS AND INTERRUPT TIMING IN QUARTER-DUTY CYCLE DRIVE
(EXAMPLE – TYPE-B, NON-STATIC)
Frame
Boundary
Frame
Boundary
LCD
Interrupt
Occurs
Controller Accesses
Next Frame Data
TFINT
TFWR
TFWR =TFRAME/2*(LMUX<1:0> + 1) + TCY/2
TFINT =(TFWR/2 – (2 TCY + 40 ns)) minimum = 1.5(TFRAME/4) – (2 TCY + 40 ns)
(TFWR/2 – (1 TCY + 40 ns)) maximum = 1.5(TFRAME/4) – (1 TCY + 40 ns)
Frame
Boundary
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
COM0
COM1
COM2
COM3
2 Frames
2008-2011 Microchip Technology Inc. DS41364E-page 357
PIC16(L)F1934/6/7
27.11 Operation During Sleep
The LCD module can operate during Sleep. The
selection is controlled by bit SLPEN of the LCDCON
register. Setting the SLPEN bit allows the LCD module
to go to Sleep. Clearing the SLPEN bit allows the
module to continue to operate during Sleep.
If a SLEEP instruction is executed and SLPEN = 1, the
LCD module will cease all functions and go into a very
low-current Consumption mode. The module will stop
operation immediately and drive the minimum LCD
voltage on both segment and common lines.
Figure 27-20 shows this operation.
The LCD module can be configured to operate during
Sleep. The selection is controlled by bit SLPEN of the
LCDCON register. Clearing SLPEN and correctly con-
figuring the LCD module clock will allow the LCD mod-
ule to operate during Sleep. Setting SLPEN and
correctly executing the LCD module shutdown will dis-
able the LCD module during Sleep and save power.
If a SLEEP instruction is executed and SLPEN = 1, the
LCD module will immediately cease all functions, drive
the outputs to Vss and go into a very Low-Current
mode. The SLEEP instruction should only be executed
after the LCD module has been disabled and the cur-
rent cycle completed, thus ensuring that there are no
DC voltages on the glass. To disable the LCD module,
clear the LCDEN bit. The LCD module will complete the
disabling process after the current frame, clear the
LCDA bit and optionally cause an interrupt.
The steps required to properly enter Sleep with the
LCD disabled are:
Clear LCDEN
Wait for LCDA = 0 either by polling or by interrupt
Execute SLEEP
If SLPEN = 0 and SLEEP is executed while the LCD
module clock source is FOSC/4, then the LCD module
will halt with the pin driving the last LCD voltage pat-
tern. Prolonged exposure to a fixed LCD voltage pat-
tern will cause damage to the LCD glass. To prevent
LCD glass damage, either perform the proper LCD
module shutdown prior to Sleep, or change the LCD
module clock to allow the LCD module to continue
operation during Sleep.
If a SLEEP instruction is executed and SLPEN = 0 and
the LCD module clock is either T1OSC or LFINTOSC,
the module will continue to display the current contents
of the LCDDATA registers. While in Sleep, the LCD
data cannot be changed. If the LCDIE bit is set, the
device will wake from Sleep on the next LCD frame
boundary. The LCD module current consumption will
not decrease in this mode; however, the overall device
power consumption will be lower due to the shutdown
of the CPU and other peripherals.
Table 27-8 shows the status of the LCD module during
a Sleep while using each of the three available clock
sources.
If a SLEEP instruction is executed and SLPEN = 0, the
module will continue to display the current contents of
the LCDDATA registers. To allow the module to
continue operation while in Sleep, the clock source
must be either the LFINTOSC or T1OSC external
oscillator. While in Sleep, the LCD data cannot be
changed. The LCD module current consumption will
not decrease in this mode; however, the overall
consumption of the device will be lower due to shut
down of the core and other peripheral functions.
Table 27-8 shows the status of the LCD module during
Sleep while using each of the three available clock
sources:
TABLE 27-8: LCD MODULE STATUS
DURING SLEEP
If LCD interrupts are being generated (Type-B wave-
form with a multiplex mode not static) and LCDIE = 1,
the device will awaken from Sleep on the next frame
boundary.
Note: When the LCDEN bit is cleared, the LCD
module will be disabled at the completion
of frame. At this time, the port pins will
revert to digital functionality. To minimize
power consumption due to floating digital
inputs, the LCD pins should be driven low
using the PORT and TRIS registers.
Clock Source SLPEN Operational
During Sleep
T1OSC 0Yes
1No
LFINTOSC 0Yes
1No
FOSC/4 0No
1No
Note: The LFINTOSC or external T1OSC
oscillator must be used to operate the
LCD module during Sleep.
PIC16(L)F1934/6/7
DS41364E-page 358 2008-2011 Microchip Technology Inc.
FIGURE 27-20: SLEEP ENTRY/EXIT WHEN SLPEN = 1
SLEEP Instruction Execution Wake-up
2 Frames
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
V3
V2
V1
V0
COM0
COM1
COM2
SEG0
2008-2011 Microchip Technology Inc. DS41364E-page 359
PIC16(L)F1934/6/7
27.12 Configuring the LCD Module
The following is the sequence of steps to configure the
LCD module.
1. Select the frame clock prescale using bits
LP<3:0> of the LCDPS register.
2. Configure the appropriate pins to function as
segment drivers using the LCDSEn registers.
3. Configure the LCD module for the following
using the LCDCON register:
- Multiplex and Bias mode, bits LMUX<1:0>
- Timing source, bits CS<1:0>
- Sleep mode, bit SLPEN
4. Write initial values to pixel data registers,
LCDDATA0 through LCDDATA11.
5. Clear LCD Interrupt Flag, LCDIF bit of the PIR2
register and if desired, enable the interrupt by
setting bit LCDIE of the PIE2 register.
6. Configure bias voltages by setting the LCDRL,
LCDREF and the associated ANSELx
registers as needed.
7. Enable the LCD module by setting bit LCDEN of
the LCDCON register.
27.13 Disabling the LCD Module
To disable the LCD module, write all ‘0s to the
LCDCON register.
27.14 LCD Current Consumption
When using the LCD module the current consumption
consists of the following three factors:
Oscillator Selection
LCD Bias Source
Capacitance of the LCD segments
The current consumption of just the LCD module can
be considered negligible compared to these other
factors.
27.14.1 OSCILLATOR SELECTION
The current consumed by the clock source selected
must be considered when using the LCD module. See
the applicable Electrical Specifications Chapter for
oscillator current consumption information.
27.14.2 LCD BIAS SOURCE
The LCD bias source, internal or external, can contrib-
ute significantly to the current consumption. Use the
highest possible resistor values while maintaining
contrast to minimize current.
27.14.3 CAPACITANCE OF THE LCD
SEGMENTS
The LCD segments which can be modeled as capaci-
tors which must be both charged and discharged every
frame. The size of the LCD segment and its technology
determines the segment’s capacitance.
PIC16(L)F1934/6/7
DS41364E-page 360 2008-2011 Microchip Technology Inc.
TABLE 27-9: SUMMARY OF REGISTERS ASSOCIATED WITH LCD OPERATION
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Register
on Page
INTCON GIE PEIE TMR0IE INTE IOCIE TMR0IF INTF IOCIF 98
LCDCON LCDEN SLPEN WERR CS<1:0> LMUX<1:0> 329
LCDCST LCDCST<2:0> 332
LCDDATA0 SEG7
COM0
SEG6
COM0
SEG5
COM0
SEG4
COM0
SEG3
COM0
SEG2
COM0
SEG1
COM0
SEG0
COM0
333
LCDDATA1 SEG15
COM0
SEG14
COM0
SEG13
COM0
SEG12
COM0
SEG11
COM0
SEG10
COM0
SEG9
COM0
SEG8
COM0
333
LCDDATA2 SEG23
COM0
SEG22
COM0
SEG21
COM0
SEG20
COM0
SEG19
COM0
SEG18
COM0
SEG17
COM0
SEG16
COM0
333
LCDDATA3 SEG7
COM1
SEG6
COM1
SEG5
COM1
SEG4
COM1
SEG3
COM1
SEG2
COM1
SEG1
COM1
SEG0
COM1
333
LCDDATA4 SEG15
COM1
SEG14
COM1
SEG13
COM1
SEG12
COM1
SEG11
COM1
SEG10
COM1
SEG9
COM1
SEG8
COM1
333
LCDDATA5 SEG23
COM1
SEG22
COM1
SEG21
COM1
SEG20
COM1
SEG19
COM1
SEG18
COM1
SEG17
COM1
SEG16
COM1
333
LCDDATA6 SEG7
COM2
SEG6
COM2
SEG5
COM2
SEG4
COM2
SEG3
COM2
SEG2
COM2
SEG1
COM2
SEG0
COM2
333
LCDDATA7 SEG15
COM2
SEG14
COM2
SEG13
COM2
SEG12
COM2
SEG11
COM2
SEG10
COM2
SEG9
COM2
SEG8
COM2
333
LCDDATA8 SEG23
COM2
SEG22
COM2
SEG21
COM2
SEG20
COM2
SEG19
COM2
SEG18
COM2
SEG17
COM2
SEG16
COM2
333
LCDDATA9 SEG7
COM3
SEG6
COM3
SEG5
COM3
SEG4
COM3
SEG3
COM3
SEG2
COM3
SEG1
COM3
SEG0
COM3
333
LCDDATA10 SEG15
COM3
SEG14
COM3
SEG13
COM3
SEG12
COM3
SEG11
COM3
SEG10
COM3
SEG9
COM3
SEG8
COM3
333
LCDDATA11 SEG23
COM3
SEG22
COM3
SEG21
COM3
SEG20
COM3
SEG19
COM3
SEG18
COM3
SEG17
COM3
SEG16
COM3
333
LCDPS WFT BIASMD LCDA WA LP<3:0> 330
LCDREF LCDIRE LCDIRS LCDIRI VLCD3PE VLCD2PE VLCD1PE 331
LCDRL LRLAP<1:0> LRLBP<1:0> —LRLAT<2:0>340
LCDSE0 SE<7:0> 333
LCDSE1 SE<15:8> 333
LCDSE2 SE<23:16> 333
PIE2 OSFIE C2IE C1IE EEIE BCLIE LCDIE CCP2IE 100
PIR2 OSFIF C2IF C1IF EEIF BCLIF LCDIF CCP2IF 103
T1CON TMR1CS<1:0> T1CKPS<1:0> T1OSCEN T1SYNC TMR1ON 203
Legend: = unimplemented location, read as 0’. Shaded cells are not used by the LCD module.
2008-2011 Microchip Technology Inc. DS41364E-page 361
PIC16(L)F1934/6/7
28.0 IN-CIRCUIT SERIAL
PROGRAMMING™ (ICSP™)
ICSP™ programming allows customers to manufacture
circuit boards with unprogrammed devices. Programming
can be done after the assembly process allowing the
device to be programmed with the most recent firmware
or a custom firmware. Five pins are needed for ICSP™
programming:
ICSPCLK
ICSPDAT
•MCLR
/VPP
•VDD
•VSS
In Program/Verify mode the Program Memory, User IDs
and the Configuration Words are programmed through
serial communications. The ICSPDAT pin is a bidirec-
tional I/O used for transferring the serial data and the
ICSPCLK pin is the clock input. For more information on
ICSP™ refer to the “PIC16193X/ PIC16LF193X Memory
Programming Specification (DS41360).
28.1 High-Voltage Programming Entry
Mode
The device is placed into High-Voltage Programming
Entry mode by holding the ICSPCLK and ICSPDAT
pins low then raising the voltage on MCLR/VPP to VIHH.
Some programmers produce VPP greater than VIHH
(9.0V), an external circuit is required to limit the VPP
voltage. See Figure 28-1 for example circuit.
FIGURE 28-1: VPP LIMITER EXAMPLE CIRCUIT
VREF
VPP
VDD
VSS
ICSP_DATA
ICSP_CLOCK
NC
RJ11-6PIN
RJ11-6PIN
R1
270 Ohm
To M PL AB ® ICD 2 To Target Bo ar d
1
2
3
4
5
61
2
3
4
5
6
R2 R3
10k 1% 24k 1%
U1
LM431BCMX
A
2
3
6
7
8
A
A
A
K
NC
NC
1
4
5
Note: The MPLAB® ICD 2 produces a VPP
voltage greater than the maximum VPP
specification of the PIC16(L)F1934/6/7.
PIC16(L)F1934/6/7
DS41364E-page 362 2008-2011 Microchip Technology Inc.
28.2 Low-Vol tage Programming Entry
Mode
The Low-Voltage Programming Entry mode allows the
PIC16(L)F1934/6/7 devices to be programmed using
VDD only, without high voltage. When the LVP bit of
Configuration Word 2 is set to ‘1’, the low-voltage ICSP
programming entry is enabled. To disable the
Low-Voltage ICSP mode, the LVP bit must be
programmed to0’.
Entry into the Low-Voltage Programming Entry mode
requires the following steps:
1. MCLR is brought to VIL.
2. A 32-bit key sequence is presented on
ICSPDAT, while clocking ICSPCLK.
Once the key sequence is complete, MCLR must be
held at VIL for as long as Program/Verify mode is to be
maintained.
If low-voltage programming is enabled (LVP = 1), the
MCLR Reset function is automatically enabled and
cannot be disabled. See Section 6.3 “MCLR for more
information.
The LVP bit can only be reprogrammed to ‘0’ by using
the High-Voltage Programming mode.
28.3 Comm on Programming Interfaces
Connection to a target device is typically done through
an ICSP™ header. A commonly found connector on
development tools is the RJ-11 in the 6P6C (6 pin, 6
connector) configuration. See Figure 28-2.
FIGURE 28-2: ICD RJ-11 STYLE
CONNECTOR INTERFACE
Another connector often found in use with the PICkit
programmers is a standard 6-pin header with 0.1 inch
spacing. Refer to Figure 28-3.
FIGURE 28-3: PI Ckit ™ STYLE CONNECTOR INTERFACE
1
2
3
4
5
6
Target
Bottom Side
PC Board
VPP/MCLR VSS
ICSPCLK
VDD
ICSPDAT
NC
Pin Description*
1 = VPP/MCLR
2 = VDD Target
3 = VSS (ground)
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
1
2
3
4
5
6
* The 6-pin header (0.100" spacing) accepts 0.025" square pins.
Pin Description*
1 = VPP/MCLR
2 = VDD Target
3 = VSS (ground)
4 = ICSPDAT
5 = ICSPCLK
6 = No Connect
Pin 1 Indicator
2008-2011 Microchip Technology Inc. DS41364E-page 363
PIC16(L)F1934/6/7
For additional interface recommendations, refer to your
specific device programmer manual prior to PCB
design.
It is recommended that isolation devices be used to
separate the programming pins from other circuitry.
The type of isolation is highly dependent on the specific
application and may include devices such as resistors,
diodes, or even jumpers. See Figure 28-4 for more
information.
FIGURE 28-4: TYPICAL CONNECTION FOR ICSP™ PROGRAMMING
VDD
VPP
VSS
External
Device to be
Data
Clock
VDD
MCLR/VPP
VSS
ICSPDAT
ICSPCLK
**
*
To Normal Connections
*Isolation devices (as required).
Programming
Signals Programmed
VDD
PIC16(L)F1934/6/7
DS41364E-page 364 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 365
PIC16(L)F1934/6/7
29.0 INSTRUCTION SET SUMMARY
Each PIC16 instruction is a 14-bit word containing the
operation code (opcode) and all required operands.
The opcodes are broken into three broad categories.
Byte Oriented
Bit Oriented
Literal and Control
The literal and control category contains the most var-
ied instruction word format.
Table 29-3 lists the instructions recognized by the
MPASMTM assembler.
All instructions are executed within a single instruction
cycle, with the following exceptions, which may take
two or three cycles:
Subroutine takes two cycles (CALL, CALLW)
Returns from interrupts or subroutines take two
cycles (RETURN, RETLW, RETFIE)
Program branching takes two cycles (GOTO, BRA,
BRW, BTFSS, BTFSC, DECFSZ, INCSFZ)
One additional instruction cycle will be used when
any instruction references an indirect file register
and the file select register is pointing to program
memory.
One instruction cycle consists of 4 oscillator cycles; for
an oscillator frequency of 4 MHz, this gives a nominal
instruction execution rate of 1 MHz.
All instruction examples use the format0xhh’ to
represent a hexadecimal number, where ‘h’ signifies a
hexadecimal digit.
29.1 Read-Modify-Write Operations
Any instruction that specifies a file register as part of
the instruction performs a Read-Modify-Write (R-M-W)
operation. The register is read, the data is modified,
and the result is stored according to either the instruc-
tion, or the destination designator ‘d’. A read operation
is performed on a register even if the instruction writes
to that register.
TABLE 29-1: OPCODE FIELD
DESCRIPTIONS
TABLE 29-2: ABBREVIATION
DESCRIPTIONS
Field Description
fRegister file address (0x00 to 0x7F)
WWorking register (accumulator)
bBit address within an 8-bit file register
kLiteral field, constant data or label
xDon’t care location (= 0 or 1).
The assembler will generate code with x = 0.
It is the recommended form of use for
compatibility with all Microchip software tools.
dDestination select; d = 0: store result in W,
d = 1: store result in file register f.
Default is d = 1.
nFSR or INDF number. (0-1)
mm Pre-post increment-decrement mode
selection
Field Description
PC Program Counter
TO Time-out bit
CCarry bit
DC Digit carry bit
ZZero bit
PD Power-down bit
PIC16(L)F1934/6/7
DS41364E-page 366 2008-2011 Microchip Technology Inc.
FIGURE 29-1: GENERAL FORMAT FOR
INSTRUCTIONS
Byte-oriented file registe r operations
13 8 7 6 0
d = 0 for destination W
OPCODE d f (FILE #)
d = 1 for destination f
f = 7-bit file register address
Bit-oriente d file register operations
13 10 9 7 6 0
OPCODE b (BIT #) f (FILE #)
b = 3-bit bit address
f = 7-bit file register address
Literal and control operations
13 8 7 0
OPCODE k (literal)
k = 8-bit immediate value
13 11 10 0
OPCODE k (literal)
k = 11-bit immediate value
General
CALL and GOTO instructions only
MOVLP instruction only
13 5 4 0
OPCODE k (literal)
k = 5-bit immediate value
MOVLB instruction only
13 9 8 0
OPCODE k (literal)
k = 9-bit immediate value
BRA instruction only
FSR Offset instructions
13 7 6 5 0
OPCODE n k (literal)
n = appropriate FSR
FSR Increment instructions
13 7 6 0
OPCODE k (literal)
k = 7-bit immediate value
13 3 2 1 0
OPCODE n m (mode)
n = appropriate FSR
m = 2-bit mode value
k = 6-bit immediate value
13 0
OPCODE
OPCODE only
2008-2011 Microchip Technology Inc. DS41364E-page 367
PIC16(L)F1934/6/7
TABLE 29-3: PIC16(L)F1934/6/7 ENHANCED INSTRUCTION SET
Mnemonic,
Operands Description Cycles 14-B it Opcod e Status
Affected Notes
MSb LSb
BYTE-ORIENTED FILE REGISTER OPERATIONS
ADDWF
ADDWFC
ANDWF
ASRF
LSLF
LSRF
CLRF
CLRW
COMF
DECF
INCF
IORWF
MOVF
MOVWF
RLF
RRF
SUBWF
SUBWFB
SWAPF
XORWF
f, d
f, d
f, d
f, d
f, d
f, d
f
f, d
f, d
f, d
f, d
f, d
f
f, d
f, d
f, d
f, d
f, d
f, d
Add W and f
Add with Carry W and f
AND W with f
Arithmetic Right Shift
Logical Left Shift
Logical Right Shift
Clear f
Clear W
Complement f
Decrement f
Increment f
Inclusive OR W with f
Move f
Move W to f
Rotate Left f through Carry
Rotate Right f through Carry
Subtract W from f
Subtract with Borrow W from f
Swap nibbles in f
Exclusive OR W with f
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
00
11
00
11
11
11
00
00
00
00
00
00
00
00
00
00
00
11
00
00
0111
1101
0101
0111
0101
0110
0001
0001
1001
0011
1010
0100
1000
0000
1101
1100
0010
1011
1110
0110
dfff
dfff
dfff
dfff
dfff
dfff
lfff
0000
dfff
dfff
dfff
dfff
dfff
1fff
dfff
dfff
dfff
dfff
dfff
dfff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
00xx
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
ffff
C, DC, Z
C, DC, Z
Z
C, Z
C, Z
C, Z
Z
Z
Z
Z
Z
Z
Z
C
C
C, DC, Z
C, DC, Z
Z
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
BYTE ORIENTED SKIP OPERATIONS
DECFSZ
INCFSZ
f, d
f, d
Decrement f, Skip if 0
Increment f, Skip if 0
1(2)
1(2)
00
00 1011
1111 dfff
dfff ffff
ffff
1, 2
1, 2
BIT-ORIENTED FILE REGISTER OPERATIONS
BCF
BSF
f, b
f, b
Bit Clear f
Bit Set f
1
1
01
01 00bb
01bb bfff
bfff ffff
ffff
2
2
BIT-ORIENTED SKIP OPERATIONS
BTFSC
BTFSS
f, b
f, b
Bit Test f, Skip if Clear
Bit Test f, Skip if Set
1 (2)
1 (2)
01
01 10bb
11bb bfff
bfff ffff
ffff
1, 2
1, 2
LITERAL OPERATIONS
ADDLW
ANDLW
IORLW
MOVLB
MOVLP
MOVLW
SUBLW
XORLW
k
k
k
k
k
k
k
k
Add literal and W
AND literal with W
Inclusive OR literal with W
Move literal to BSR
Move literal to PCLATH
Move literal to W
Subtract W from literal
Exclusive OR literal with W
1
1
1
1
1
1
1
1
11
11
11
00
11
11
11
11
1110
1001
1000
0000
0001
0000
1100
1010
kkkk
kkkk
kkkk
001k
1kkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
kkkk
C, DC, Z
Z
Z
C, DC, Z
Z
Note 1:If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second cycle is
executed as a NOP.
2: If this instruction addresses an INDF register and the MSb of the corresponding FSR is set, this instruction will require one
additional instruction cycle.
PIC16(L)F1934/6/7
DS41364E-page 368 2008-2011 Microchip Technology Inc.
TABLE 29-3: PIC16(L)F1938/9 ENHANCED INSTRUCTION SET (CONTINUED)
Mnemonic,
Operands Description Cycles 14-B it Opcod e Status
Affected Notes
MSb LSb
CONTROL OPERATIONS
BRA
BRW
CALL
CALLW
GOTO
RETFIE
RETLW
RETURN
k
k
k
k
k
Relative Branch
Relative Branch with W
Call Subroutine
Call Subroutine with W
Go to address
Return from interrupt
Return with literal in W
Return from Subroutine
2
2
2
2
2
2
2
2
11
00
10
00
10
00
11
00
001k
0000
0kkk
0000
1kkk
0000
0100
0000
kkkk
0000
kkkk
0000
kkkk
0000
kkkk
0000
kkkk
1011
kkkk
1010
kkkk
1001
kkkk
1000
INHERENT OPERATIONS
CLRWDT
NOP
OPTION
RESET
SLEEP
TRIS
f
Clear Watchdog Timer
No Operation
Load OPTION_REG register with W
Software device Reset
Go into Standby mode
Load TRIS register with W
1
1
1
1
1
1
00
00
00
00
00
00
0000
0000
0000
0000
0000
0000
0110
0000
0110
0000
0110
0110
0100
0000
0010
0001
0011
0fff
TO, PD
TO, PD
C-COMPILER OPTIMIZED
ADDFSR
MOVIW
MOVWI
n, k
n mm
k[n]
n mm
k[n]
Add Literal k to FSRn
Move Indirect FSRn to W with pre/post inc/dec
modifier, mm
Move INDFn to W, Indexed Indirect.
Move W to Indirect FSRn with pre/post inc/dec
modifier, mm
Move W to INDFn, Indexed Indirect.
1
1
1
1
1
11
00
11
00
11
0001
0000
1111
0000
1111
0nkk
0001
0nkk
0001
1nkk
kkkk
0nmm
kkkk
1nmm
kkkk
Z
Z
2, 3
2
2, 3
2
Note 1:If the Program Counter (PC) is modified, or a conditional test is true, the instruction requires two cycles. The second cycle is
executed as a NOP.
2: If this instruction addresses an INDF register and the MSb of the corresponding FSR is set, this instruction will require
one additional instruction cycle.
3: See Table in the MOVIW and MOVWI instruction descriptions.
2008-2011 Microchip Technology Inc. DS41364E-page 369
PIC16(L)F1934/6/7
29.2 Instruction Descripti ons
ADDFSR Add Literal to FSRn
Syntax: [ label ] ADDFSR FSRn, k
Operands: -32 k 31
n [ 0, 1]
Operation: FSR(n) + k FSR(n)
Status Affected: None
Description: The signed 6-bit literal ‘k’ is added to
the contents of the FSRnH:FSRnL
register pair.
FSRn is limited to the range 0000h -
FFFFh. Moving beyond these bounds
will cause the FSR to wrap around.
ADDLW Add literal and W
Syntax: [ label ] ADDLW k
Operands: 0 k 255
Operation: (W) + k (W)
Status Affected: C, DC, Z
Description: The contents of the W register are
added to the eight-bit literal ‘k’ and the
result is placed in the W register.
ADDWF Add W and f
Syntax: [ label ] ADDWF f,d
Operands: 0 f 127
d 0,1
Operation: (W) + (f) (destination)
Status Affected: C, DC, Z
Description: Add the contents of the W register
with register ‘f’. If ‘d’ is ‘0’, the result is
stored in the W register. If ‘d’ is ‘1’, the
result is stored back in register ‘f’.
ADDWFC ADD W a nd CARRY bit to f
Syntax: [ label ] ADDWFC f {,d}
Operands: 0 f 127
d [0,1]
Operation: (W) + (f) + (C) dest
Status Affected: C, DC, Z
Description: Add W, the Carry flag and data mem-
ory location ‘f’. If ‘d’ is0’, the result is
placed in W. If ‘d’ is ‘1’, the result is
placed in data memory location ‘f’.
ANDLW AND literal with W
Syntax: [ label ] ANDLW k
Operands: 0 k 255
Operation: (W) .AND. (k) (W)
Status Affected: Z
Description: The contents of W register are
AND’ed with the eight-bit literal ‘k’.
The result is placed in the W register.
ANDWF AND W with f
Syntax: [ label ] ANDWF f,d
Operands: 0 f 127
d 0,1
Operation: (W) .AND. (f) (destination)
Status Affected: Z
Description: AND the W register with register ‘f’. If
‘d’ is 0’, the result is stored in the W
register. If ‘d’ is ‘1’, the result is stored
back in register ‘f’.
ASRF Arithmetic Right Shift
Syntax: [ label ] ASRF f {,d}
Operands: 0 f 127
d [0,1]
Operation: (f<7>) dest<7>
(f<7:1>) dest<6:0>,
(f<0>) C,
Status Affected: C, Z
Description: The contents of register ‘f’ are shifted
one bit to the right through the Carry
flag. The MSb remains unchanged. If
‘d’ is ‘0’, the result is placed in W. If ‘d’
is ‘1’, the result is stored back in reg-
ister ‘f’.
register f C
PIC16(L)F1934/6/7
DS41364E-page 370 2008-2011 Microchip Technology Inc.
BCF Bit Clear f
Syntax: [ label ] BCF f,b
Operands: 0 f 127
0 b 7
Operation: 0 (f<b>)
Status Affected: None
Description: Bit ‘b’ in register ‘f’ is cleared.
BRA Relative Branch
Syntax: [ label ] BRA label
[ label ] BRA $+k
Operands: -256 label - PC + 1 255
-256 k 255
Operation: (PC) + 1 + k PC
Status Affected: None
Description: Add the signed 9-bit literal ‘k’ to the
PC. Since the PC will have incre-
mented to fetch the next instruction,
the new address will be PC + 1 + k.
This instruction is a two-cycle instruc-
tion. This branch has a limited range.
BRW Relative Branch with W
Syntax: [ label ] BRW
Operands: None
Operation: (PC) + (W) PC
Status Affected: None
Description: Add the contents of W (unsigned) to
the PC. Since the PC will have incre-
mented to fetch the next instruction,
the new address will be PC + 1 + (W).
This instruction is a two-cycle instruc-
tion.
BSF Bit Set f
Syntax: [ label ] BSF f,b
Operands: 0 f 127
0 b 7
Operation: 1 (f<b>)
Status Affected: None
Description: Bit ‘b’ in register ‘f’ is set.
BTFSC Bit Test f, Skip if Clear
Syntax: [ label ] BTFSC f,b
Operands: 0 f 127
0 b 7
Operation: skip if (f<b>) = 0
Status Affected: None
Description: If bit ‘b’ in register ‘f’ is ‘1’, the next
instruction is executed.
If bit ‘b’, in register ‘f’, is ‘0’, the next
instruction is discarded, and a NOP is
executed instead, making this a
2-cycle instruction.
BTFSS Bit Test f, Skip if Set
Syntax: [ label ] BTFSS f,b
Operands: 0 f 127
0 b < 7
Operation: skip if (f<b>) = 1
Status Affected: None
Description: If bit ‘b’ in register ‘f’ is 0’, the next
instruction is executed.
If bit ‘b’ is ‘1’, then the next
instruction is discarded and a NOP is
executed instead, making this a
2-cycle instruction.
2008-2011 Microchip Technology Inc. DS41364E-page 371
PIC16(L)F1934/6/7
CALL Call Subroutine
Syntax: [ label ] CALL k
Operands: 0 k 2047
Operation: (PC)+ 1 TOS,
k PC<10:0>,
(PCLATH<6:3>) PC<14:11>
Status Affected: None
Description: Call Subroutine. First, return address
(PC + 1) is pushed onto the stack.
The eleven-bit immediate address is
loaded into PC bits <10:0>. The upper
bits of the PC are loaded from
PCLATH. CALL is a two-cycle instruc-
tion.
CALLW Subroutine Call With W
Syntax: [ label ] CALLW
Operands: None
Operation: (PC) +1 TOS,
(W) PC<7:0>,
(PCLATH<6:0>) PC<14:8>
Status Affected: None
Description: Subroutine call with W. First, the
return address (PC + 1) is pushed
onto the return stack. Then, the con-
tents of W is loaded into PC<7:0>,
and the contents of PCLATH into
PC<14:8>. CALLW is a two-cycle
instruction.
CLRF Clear f
Syntax: [ lab el ] CLRF f
Operands: 0 f 127
Operation: 00h (f)
1 Z
Status Affected: Z
Description: The contents of register ‘f’ are cleared
and the Z bit is set.
CLRW Clear W
Syntax: [ label ] CLRW
Operands: None
Operation: 00h (W)
1 Z
Status Affected: Z
Description: W register is cleared. Zero bit (Z) is
set.
CLRWDT Clear Watchdog Timer
Syntax: [ label ] CLRWDT
Operands: None
Operation: 00h WDT
0 WDT prescaler,
1 TO
1 PD
Status Affected: TO, PD
Description: CLRWDT instruction resets the Watch-
dog Timer. It also resets the prescaler
of the WDT.
Status bits TO and PD are set.
COMF C omplement f
Syntax: [ label ] COMF f,d
Operands: 0 f 127
d [0,1]
Operation: (f) (destination)
Status Affected: Z
Description: The contents of register ‘f’ are com-
plemented. If ‘d’ is 0’, the result is
stored in W. If ‘d’ is ‘1’, the result is
stored back in register ‘f’.
DECF Decrement f
Syntax: [ label ] DECF f,d
Operands: 0 f 127
d [0,1]
Operation: (f) - 1 (destination)
Status Affected: Z
Description: Decrement register ‘f’. If ‘d’ is 0’, the
result is stored in the W
register. If ‘d’ is ‘1’, the result is stored
back in register ‘f’.
PIC16(L)F1934/6/7
DS41364E-page 372 2008-2011 Microchip Technology Inc.
DECFSZ Decrement f, Skip if 0
Syntax: [ label ] DECFSZ f,d
Operands: 0 f 127
d [0,1]
Operation: (f) - 1 (destination);
skip if result = 0
Status Affected: None
Description: The contents of register ‘f’ are decre-
mented. If ‘d’ is ‘0’, the result is placed
in the W register. If ‘d’ is ‘1’, the result
is placed back in register ‘f’.
If the result is ‘1’, the next instruction is
executed. If the result is ‘0, then a
NOP is executed instead, making it a
2-cycle instruction.
GOTO Unconditional Branch
Syntax: [ label ] GOTO k
Operands: 0 k 2047
Operation: k PC<10:0>
PCLATH<6:3> PC<14:11>
Status Affected: None
Description: GOTO is an unconditional branch. The
eleven-bit immediate value is loaded
into PC bits <10:0>. The upper bits of
PC are loaded from PCLATH<4:3>.
GOTO is a two-cycle instruction.
INCF Increment f
Syntax: [ label ] INCF f,d
Operands: 0 f 127
d [0,1]
Operation: (f) + 1 (destination)
Status Affected: Z
Description: The contents of register ‘f’ are incre-
mented. If ‘d’ is ‘0’, the result is placed
in the W register. If ‘d’ is ‘1’, the result
is placed back in register ‘f’.
INCFSZ Increment f, Skip if 0
Syntax: [ label ] INCFSZ f,d
Operands: 0 f 127
d [0,1]
Operation: (f) + 1 (destination),
skip if result = 0
Status Affected: None
Description: The contents of register ‘f’ are incre-
mented. If ‘d’ is ‘0’, the result is placed
in the W register. If ‘d’ is ‘1’, the result
is placed back in register ‘f’.
If the result is ‘1’, the next instruction is
executed. If the result is ‘0’, a NOP is
executed instead, making it a 2-cycle
instruction.
IORLW Inclusive OR literal with W
Syntax: [ label ] IORLW k
Operands: 0 k 255
Operation: (W) .OR. k (W)
Status Affected: Z
Description: The contents of the W register are
OR’ed with the eight-bit literal ‘k’. The
result is placed in the W register.
IORWF Inclusive OR W with f
Syntax: [ label ] IORWF f,d
Operands: 0 f 127
d [0,1]
Operation: (W) .OR. (f) (destination)
Status Affected: Z
Description: Inclusive OR the W register with regis-
ter ‘f’. If ‘d’ is ‘0’, the result is placed in
the W register. If ‘d’ is ‘1’, the result is
placed back in register ‘f’.
2008-2011 Microchip Technology Inc. DS41364E-page 373
PIC16(L)F1934/6/7
LSLF Logical Left Shift
Syntax: [ label ] LSLF f {,d}
Operands: 0 f 127
d [0,1]
Operation: (f<7>) C
(f<6:0>) dest<7:1>
0 dest<0>
Status Affected: C, Z
Description: The contents of register ‘f’ are shifted
one bit to the left through the Carry flag.
A ‘0’ is shifted into the LSb. If ‘d’ is ‘0’,
the result is placed in W. If ‘d’ is ‘1’, the
result is stored back in register ‘f’.
LSRF Logical Right Shift
Syntax: [ label ] LSLF f {,d}
Operands: 0 f 127
d [0,1]
Operation: 0 dest<7>
(f<7:1>) dest<6:0>,
(f<0>) C,
Status Affected: C, Z
Description: The contents of register ‘f’ are shifted
one bit to the right through the Carry
flag. A ‘0’ is shifted into the MSb. If ‘d’ is
0’, the result is placed in W. If ‘d’ is ‘1’,
the result is stored back in register ‘f’.
register f 0
C
register f C0
MOVF Move f
Syntax: [ label ] MOVF f,d
Operands: 0 f 127
d [0,1]
Operation: (f) (dest)
Status Affected: Z
Description: The contents of register f is moved to
a destination dependent upon the
status of d. If d = 0,
destination is W register. If d = 1, the
destination is file register f itself. d = 1
is useful to test a file register since
status flag Z is affected.
Words: 1
Cycles: 1
Example: MOVF FSR, 0
After Instruction
W = value in FSR register
Z= 1
PIC16(L)F1934/6/7
DS41364E-page 374 2008-2011 Microchip Technology Inc.
MOVIW Move INDFn to W
Syntax: [ label ] MOVIW ++FSRn
[ label ] MOVIW --FSRn
[ label ] MOVIW FSRn++
[ label ] MOVIW FSRn--
[ label ] MOVIW k[FSRn]
Operands: n [0,1]
mm [00,01, 10, 11]
-32 k 31
Operation: INDFn W
Effective address is determined by
FSR + 1 (preincrement)
FSR - 1 (predecrement)
FSR + k (relative offset)
After the Move, the FSR value will be
either:
FSR + 1 (all increments)
FSR - 1 (all decrements)
Unchanged
Status Affected: Z
Mode Syntax mm
Preincrement ++FSRn 00
Predecrement --FSRn 01
Postincrement FSRn++ 10
Postdecrement FSRn-- 11
Description: This instruction is used to move data
between W and one of the indirect
registers (INDFn). Before/after this
move, the pointer (FSRn) is updated by
pre/post incrementing/decrementing it.
Note: The INDFn registers are not
physical registers. Any instruction that
accesses an INDFn register actually
accesses the register at the address
specified by the FSRn.
FSRn is limited to the range 0000h -
FFFFh. Incrementing/decrementing it
beyond these bounds will cause it to wrap
around.
MOVLB Move literal to BSR
Syntax: [ label ] MOVLB k
Operands: 0 k 15
Operation: k BSR
Status Affected: None
Description: The five-bit literal ‘k’ is loaded into the
Bank Select Register (BSR).
MOVLP Move literal to PCLATH
Syntax: [ label ] MOVLP k
Operands: 0 k 127
Operation: k PCLATH
Status Affected: None
Description: The seven-bit literal ‘k’ is loaded into the
PCLATH register.
MOVLW Move literal t o W
Syntax: [ label ] MOVLW k
Operands: 0 k 255
Operation: k (W)
Status Affected: None
Description: The eight-bit literal ‘k’ is loaded into W
register. The “don’t cares” will assem-
ble as ‘0’s.
Words: 1
Cycles: 1
Example: MOVLW 0x5A
After Instruction
W = 0x5A
MOVWF Mo ve W to f
Syntax: [ label ] MOVWF f
Operands: 0 f 127
Operation: (W) (f)
Status Affected: None
Description: Move data from W register to register
‘f’.
Words: 1
Cycles: 1
Example: MOVWF OPTION_REG
Before Instruction
OPTION_REG = 0xFF
W = 0x4F
After Instruction
OPTION_REG = 0x4F
W = 0x4F
2008-2011 Microchip Technology Inc. DS41364E-page 375
PIC16(L)F1934/6/7
MOVWI Move W to INDFn
Syntax: [ label ] MOVWI ++FSRn
[ label ] MOVWI --FSRn
[ label ] MOVWI FSRn++
[ label ] MOVWI FSRn--
[ label ] MOVWI k[FSRn]
Operands: n [0,1]
mm [00,01, 10, 11]
-32 k 31
Operation: W INDFn
Effective address is determined by
FSR + 1 (preincrement)
FSR - 1 (predecrement)
FSR + k (relative offset)
After the Move, the FSR value will be
either:
FSR + 1 (all increments)
FSR - 1 (all decrements)
Unchanged
Status Affected: None
Mode Syntax mm
Preincrement ++FSRn 00
Predecrement --FSRn 01
Postincrement FSRn++ 10
Postdecrement FSRn-- 11
Description: This instruction is used to move data
between W and one of the indirect
registers (INDFn). Before/after this
move, the pointer (FSRn) is updated by
pre/post incrementing/decrementing it.
Note: The INDFn registers are not
physical registers. Any instruction that
accesses an INDFn register actually
accesses the register at the address
specified by the FSRn.
FSRn is limited to the range 0000h -
FFFFh. Incrementing/decrementing it
beyond these bounds will cause it to wrap
around.
The increment/decrement operation on
FSRn WILL NOT affect any Status bits.
NOP No Operation
Syntax: [ label ] NOP
Operands: None
Operation: No operation
Status Affected: None
Description: No operation.
Words: 1
Cycles: 1
Example: NOP
OPTION Load OPTION_REG Register
with W
Syntax: [ label ] OPTION
Operands: None
Operation: (W) OPTION_REG
Status Affected: None
Description: Move data from W register to
OPTION_REG register.
Words: 1
Cycles: 1
Example: OPTION
Before Instruction
OPTION_REG = 0xFF
W = 0x4F
After Instruction
OPTION_REG = 0x4F
W = 0x4F
RESET Software Reset
Syntax: [ label ] RESET
Operands: None
Operation: Execute a device Reset. Resets the
nRI flag of the PCON register.
Status Affected: None
Description: This instruction provides a way to
execute a hardware Reset by soft-
ware.
PIC16(L)F1934/6/7
DS41364E-page 376 2008-2011 Microchip Technology Inc.
RETFIE Return from Interrupt
Syntax: [ label ] RETFIE
Operands: None
Operation: TOS PC,
1 GIE
Status Affected: None
Description: Return from Interrupt. Stack is POPed
and Top-of-Stack (TOS) is loaded in
the PC. Interrupts are enabled by
setting Global
Interrupt Enable bit, GIE
(INTCON<7>). This is a two-cycle
instruction.
Words: 1
Cycles: 2
Example: RETFIE
After Interrupt
PC = TOS
GIE = 1
RETLW Return with literal in W
Syntax: [ label ] RETLW k
Operands: 0 k 255
Operation: k (W);
TOS PC
Status Affected: None
Description: The W register is loaded with the eight
bit literal ‘k’. The program counter is
loaded from the top of the stack (the
return address). This is a two-cycle
instruction.
Words: 1
Cycles: 2
Example:
TABLE
CALL TABLE;W contains table
;offset value
;W now has table value
ADDWF PC ;W = offset
RETLW k1 ;Begin table
RETLW k2 ;
RETLW kn ; End of table
Before Instruction
W = 0x07
After Instruction
W = value of k8
RETURN Return from Subroutine
Syntax: [ label ] RETURN
Operands: None
Operation: TOS PC
Status Affected: None
Description: Return from subroutine. The stack is
POPed and the top of the stack (TOS)
is loaded into the program counter.
This is a two-cycle instruction.
RLF Rotate Left f through Carry
Syntax: [ label ] RLF f,d
Operands: 0 f 127
d [0,1]
Operation: See description below
Status Affected: C
Description: The contents of register ‘f’ are rotated
one bit to the left through the Carry
flag. If ‘d’ is ‘0’, the result is placed in
the W register. If ‘d’ is ‘1’, the result is
stored back in register ‘f’.
Words: 1
Cycles: 1
Example: RLF REG1,0
Before Instruction
REG1 = 1110 0110
C=0
After Instruction
REG1 = 1110 0110
W = 1100 1100
C=1
Register fC
2008-2011 Microchip Technology Inc. DS41364E-page 377
PIC16(L)F1934/6/7
RRF Rotate Right f through Carry
Syntax: [ label ] RRF f,d
Operands: 0 f 127
d [0,1]
Operation: See description below
Status Affected: C
Description: The contents of register ‘f’ are rotated
one bit to the right through the Carry
flag. If ‘d’ is 0’, the result is placed in
the W register. If ‘d’ is ‘1’, the result is
placed back in register ‘f’.
SLEEP Enter Sleep mode
Syntax: [ label ]SLEEP
Operands: None
Operation: 00h WDT,
0 WDT prescaler,
1 TO,
0 PD
Status Affected: TO, PD
Description: The power-down Status bit, PD is
cleared. Time-out Status bit, TO is
set. Watchdog Timer and its pres-
caler are cleared.
The processor is put into Sleep mode
with the oscillator stopped.
Register fC
SUBLW Subtract W from literal
Syntax: [ label ]SUBLW k
Operands: 0 k 255
Operation: k - (W) W)
Status Affected: C, DC, Z
Description: The W register is subtracted (2’s com-
plement method) from the eight-bit
literal ‘k’. The result is placed in the W
register.
SUBWF Subtract W from f
Syntax: [ label ] SUBWF f,d
Operands: 0 f 127
d [0,1]
Operation: (f) - (W) destination)
Status Affected: C, DC, Z
Description: Subtract (2’s complement method) W
register from register ‘f’. If ‘d’ is ‘0’, the
result is stored in the W
register. If ‘d’ is1’, the result is stored
back in register ‘f.
SUBWFB Subtract W from f with Borrow
Syntax: SUBWFB f {,d}
Operands: 0 f 127
d [0,1]
Operation: (f) – (W) – (B) dest
Status Affected: C, DC, Z
Description: Subtract W and the BORROW flag
(CARRY) from register ‘f’ (2’s comple-
ment method). If ‘d’ is ‘0’, the result is
stored in W. If ‘d’ is ‘1’, the result is
stored back in register ‘f’.
C = 0W k
C = 1W k
DC = 0W<3:0> k<3:0>
DC = 1W<3:0> k<3:0>
C = 0W f
C = 1W f
DC = 0W<3:0> f<3:0>
DC = 1W<3:0> f<3:0>
PIC16(L)F1934/6/7
DS41364E-page 378 2008-2011 Microchip Technology Inc.
SWAPF Swap Nibbles in f
Syntax: [ label ] SWAPF f,d
Operands: 0 f 127
d [0,1]
Operation: (f<3:0>) (destination<7:4>),
(f<7:4>) (destination<3:0>)
Status Affected: None
Description: The upper and lower nibbles of regis-
ter ‘f’ are exchanged. If ‘d’ is 0’, the
result is placed in the W register. If ‘d’
is ‘1’, the result is placed in register ‘f’.
TRIS Load TRIS Register with W
Syntax: [ label ] TRIS f
Operands: 5 f 7
Operation: (W) TRIS register ‘f’
Status Affected: None
Description: Move data from W register to TRIS
register.
When ‘f’ = 5, TRISA is loaded.
When ‘f’ = 6, TRISB is loaded.
When ‘f’ = 7, TRISC is loaded.
XORLW Exclusive OR literal with W
Syntax: [ label ] XORLW k
Operands: 0 k 255
Operation: (W) .XOR. k W)
Status Affected: Z
Description: The contents of the W register are
XOR’ed with the eight-bit
literal ‘k’. The result is placed in the
W register.
XORWF Exclusive OR W with f
Syntax: [ label ] XORWF f,d
Operands: 0 f 127
d [0,1]
Operation: (W) .XOR. (f) destination)
Status Affected: Z
Description: Exclusive OR the contents of the W
register with register ‘f’. If ‘d’ is ‘0’, the
result is stored in the W register. If ‘d’
is ‘1’, the result is stored back in regis-
ter ‘f’.
2008-2011 Microchip Technology Inc. DS41364E-page 379
PIC16(L)F1934/6/7
30.0 ELECTRICAL SPECIFICATIONS
Absolute Maximum Ratings(†)
Ambient temperature under bias....................................................................................................... -40°C to +125°C
Storage temperature ........................................................................................................................ -65°C to +150°C
Voltage on VDD with respect to VSS ................................................................................................... -0.3V to +6.5V
Voltage on VCAP pin with respect to VSS.............................................................................................. -0.3V to +4.0V
Voltage on VDD with respect to VSS ................................................................................................... -0.3V to +4.0V
Voltage on MCLR with respect to Vss ................................................................................................. -0.3V to +9.0V
Voltage on all other pins with respect to VSS ........................................................................... -0.3V to (VDD + 0.3V)
Total power dissipation(1) ............................................................................................................................... 800 mW
Maximum current out of VSS(2) pin, -40°C TA +85°C for industrial ........................................................... 255 mA
Maximum current out of VSS(2) pin, -40°C TA +125°C for extended......................................................... 105 mA
Maximum current into VDD(2) pin, -40°C TA +85°C for industrial .............................................................. 170 mA
Maximum current into VDD(2) pin, -40°C TA +125°C for extended.............................................................. 70 mA
Clamp current, IK (VPIN < 0 or VPIN > VDD)20 mA
Maximum output current sunk by any I/O pin.................................................................................................... 25 mA
Maximum output current sourced by any I/O pin .............................................................................................. 25 mA
Note 1: Power dissipation is calculated as follows: PDIS = VDD x {IDD IOH} + {(VDD – VOH) x IOH} + (VOl x IOL)
2: For 28-pin devices.
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operation listings of this specification is not implied. Exposure above maximum rating conditions for
extended periods may affect device reliability.
PIC16(L)F1934/6/7
DS41364E-page 380 2008-2011 Microchip Technology Inc.
FIGURE 30-1: PIC16F1934/36/37 VOLTAGE FREQUENCY GRAPH, -40°C
TA

+125°C
FIGURE 30-2: PI C16L F19 34/3 6/37 VOLTAGE FREQUENCY GRAPH, -40°C
TA

+125°C
1.8
0
2.5
Frequency (MHz)
VDD (V)
Note 1: The shaded region indicates the permissible combinations of voltage and frequency.
2: Refer to Table 30-1 for each Oscillator mode’s supported frequencies.
43210 16
5.5
1.8
0
2.5
Frequency (MHz )
VDD (V)
Note 1: The shaded region indicates the permissible combinations of voltage and frequency.
2: Refer to Table 30-1 for each Oscillator mode’s supported frequencies.
432
10 16
3.6
2008-2011 Microchip Technology Inc. DS41364E-page 381
PIC16(L)F1934/6/7
FIGURE 30-3: HFINTOSC FREQUENCY ACCURACY OVER DEVICE VDD AND TEMPERATURE
125
25
2.0
0
60
85
VDD (V)
4.0 5.04.5
Temperature (°C)
2.5 3.0 3.5 5.51.8
-40
± 5%
± 2%
± 5%
± 3%
PIC16(L)F1934/6/7
DS41364E-page 382 2008-2011 Microchip Technology Inc.
30.1 DC Characteris tics: PIC16(L)F1934/6/7- I/E (Industrial, Extended)
PIC16LF1934/36/37 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
PIC16F1934/36/37 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param.
No. Sym. Characteristic Min. Typ† Max. Units Conditions
D001 VDD Supply Voltage
PIC16LF1934/36/37 1.8
2.3
3.6
3.6
V
V
FOSC 16 MHz:
FOSC 32 MHz (Note 2 )
D001 PIC16F1934/36/37 1.8
2.3
5.5
5.5
V
V
FOSC 16 MHz:
FOSC 32 MHz (Note 2 )
D002* VDR RAM Data Retention Voltage(1)
PIC16LF1934/36/37 1.5 V Device in Sleep mode
D002* PIC16F1934/36/37 1.7 V Device in Sleep mode
VPOR*Power-on Reset Release Voltage —1.6 V
VPORR*Power-on R eset Rearm Voltage
PIC16LF1934/36/37 0.8 V Device in Sleep mode
PIC16F1934/36/37 1.7 V Device in Sleep mode
D003 VADFVR Fixed Voltage Reference Voltage
for ADC -8 6 % 1.024V, VDD 2.5V
2.048V, VDD 2.5V
4.096V, VDD 4.75V
D003A VCDAFVR Fixed Voltage Reference Voltage
for Comparator and DAC -11 7 % 1.024V, VDD 2.5V
2.048V, VDD 2.5V
4.096V, VDD 4.75V
D003B VLCDFVR Fixed Voltage Reference Voltage
for LCD Bias -11 10 % 3.072V, VDD 3.6V
D004* SVDD VDD Rise Rate to ensure internal
Power-on Reset signal
0.05 V/ms See Section 6.1 “Power-on Reset
(POR)” for details.
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: This is the limit to which VDD can be lowered in Sleep mode without losing RAM data.
2: PLL required for 32 MHz operation.
2008-2011 Microchip Technology Inc. DS41364E-page 383
PIC16(L)F1934/6/7
FIGURE 30-4: POR AND POR REARM WITH SLOW RISING VDD
VDD
VPOR
VPORR
VSS
VSS
NPOR
TPOR(3)
POR REARM
Note 1: When NPOR is low, the device is held in Reset.
2: TPOR 1 s typical.
3: TVLOW 2.7 s typical.
TVLOW(2)
PIC16(L)F1934/6/7
DS41364E-page 384 2008-2011 Microchip Technology Inc.
30.2 DC Characteris tics: PIC16(L)F1934/6/7- I/E (Industrial, Extended)
PIC16LF1934/36/37 Standard Opera ting Conditions (unles s otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
PIC16F1934/36/37 Standard Oper ating Condi tions (unles s otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Device
Characteristics Min. Typ† Max. Units Conditions
VDD Note
Supply Current (IDD)(1, 2)
D009 LDO Regulator 350 A HS, EC OR INTOSC/INTOSCIO (8-16 MHZ)
Clock modes with all VCAP pins disabled
50 A All VCAP pins disabled
30 A VCAP enabled on RA0, RA5 or RA6
5 A LP Clock mode and Sleep (requires FVR and
BOR to be disabled)
D010 7.0 16 A1.8F
OSC = 32 kHz
LP Oscillator mode (Note 4),
-40°C TA +85°C
—9.0 20 A3.0
D010 29 63 A1.8 FOSC = 32 kHz
LP Oscillator mode (Note 4, 5),
-40°C TA +85°C
37 74 A3.0
40 79 A5.0
D010A 7.0 23 A1.8
FOSC = 32 kHz
LP Oscillator mode (Note 4)
-40°C TA +125°C
—9.0 27 A3.0
D010A 29 68 A1.8 FOSC = 32 kHz
LP Oscillator mode (Note 4, 5)
-40°C TA +125°C
37 88 A3.0
40 95 A5.0
D011 140 200 A1.8F
OSC = 1 MHz
XT Oscillator mode
—250
330 A3.0
D011 160 260 A1.8 FOSC = 1 MHz
XT Oscillator mode (Note 5)
280 480 A3.0
390 690 A5.0
D012 430 650 A1.8F
OSC = 4 MHz
XT Oscillator mode
750 1000 A3.0
D012 450 700 A1.8 FOSC = 4 MHz
XT Oscillator mode (Note 5)
770 1100 A3.0
930 1300 A5.0
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: 0.1 F capacitor on VCAP (RA0).
6: 8 MHz crystal oscillator with 4x PLL enabled.
2008-2011 Microchip Technology Inc. DS41364E-page 385
PIC16(L)F1934/6/7
Supply Current (IDD)(1, 2)
D013 50 100 A1.8FOSC = 500 kHz
EC Oscillator Low-Power mode
—85
150 A3.0
D013 70 120 A1.8 FOSC = 500 kHz
EC Oscillator Low-Power mode (Note 5)
115 170 A3.0
120 200 A5.0
D014 400 550 A1.8F
OSC = 4 MHz
EC Oscillator mode
Medium Power mode
—700
1100 A3.0
D014 430 650 A1.8 FOSC = 4 MHz
EC Oscillator mode (Note 5)
Medium Power mode
720 1000 A3.0
850 1200 A5.0
D015 5.3 6.2 mA 3.0 FOSC = 32 MHz
EC Oscillator High-Power mode
—6.37.5 mA 3.6
D015 5.3 6.5 mA 3.0 FOSC = 32 MHz
EC Oscillator High-Power mode (Note 5)
5.4 7.5 mA 5.0
D016 5 12 A1.8F
OSC = 32 kHz, LFINTOSC mode (Note 4)
-40°C TA +85°C
—8 16 A3.0
D016 27 70 A1.8 FOSC = 32 kHz, LFINTOSC mode
(Note 4, Note 5)
-40°C TA +85°C
34 80 A3.0
36 90 A5.0
30.2 DC Characteri stics: PIC16(L)F1934/6/7-I/E (Industrial, Extended) (Continued)
PIC16LF1934/36/37 Standard Operating Condit ion s (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
PIC16F1934/36/37 Standard Operating Condi t ions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Device
Characteristics Min. Typ† Max. Units Conditions
VDD Note
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: 0.1 F capacitor on VCAP (RA0).
6: 8 MHz crystal oscillator with 4x PLL enabled.
PIC16(L)F1934/6/7
DS41364E-page 386 2008-2011 Microchip Technology Inc.
D017 Supply Current (IDD)(1, 2)
—110
180 A1.8FOSC = 500 kHz
MFINTOSC mode
—140
250 A3.0
D017 150 250 A1.8 FOSC = 500 kHz
MFINTOSC mode (Note 5)
210 330 A3.0
270 430 A5.0
D018 1.0 1.4 mA 1.8 FOSC = 8 MHz
HFINTOSC mode
—1.82.3 mA 3.0
D018 1.0 1.5 mA 1.8 FOSC = 8 MHz
HFINTOSC mode (Note 5)
1.8 2.3 mA 3.0
2.0 2.8 mA 5.0
D019 1.5 2.2 mA 1.8 FOSC = 16 MHz
HFINTOSC mode
—2.83.7 mA 3.0
D019 1.7 2.3 mA 1.8 FOSC = 16 MHz
HFINTOSC mode (Note 5)
2.9 3.9 mA 3.0
3.1 4.1 mA 5.0
D020 4.8 6.2 mA 3.0 FOSC = 32 MHz
HFINTOSC mode
—5.07.5 mA 3.6
D020 4.8 6.5 mA 3.0 FOSC = 32 MHz
HFINTOSC mode
5.0 7.5 mA 5.0
D021 410 550 A1.8F
OSC = 4 MHz
EXTRC mode (Note 3)
710 990 A3.0
D021 430 700 A1.8 FOSC = 4 MHz
EXTRC mode (Note 3, Note 5)
730 1100 A3.0
860 1400 A5.0
D022 5.0 6.2 mA 3.0 FOSC = 32 MHz
HS Oscillator mode (Note 6)
—6.07.5 mA 3.6
D022 5.0 6.5 mA 3.0 FOSC = 32 MHz
HS Oscillator mode (Note 5, Note 6)
5.2 7.5 mA 5.0
30.2 DC Characteristics: PIC16(L)F1934/6/7-I/E (Industrial, Extended) (Continued)
PIC16LF1934/36/37 Standard Opera ting Conditions (unles s otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
PIC16F1934/36/37 Standard Oper ating Condi tions (unles s otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Device
Characteristics Min. Typ† Max. Units Conditions
VDD Note
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k
4: FVR and BOR are disabled.
5: 0.1 F capacitor on VCAP (RA0).
6: 8 MHz crystal oscillator with 4x PLL enabled.
2008-2011 Microchip Technology Inc. DS41364E-page 387
PIC16(L)F1934/6/7
30.3 DC Characteristics: PIC16(L)F1934/6/7- I/E (Power-Down)
PIC16LF1934/36/37 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
PIC16F1934/36/37 Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Device Characteristics Min. Typ† Max.
+85°C Max.
+125°C Units Conditions
VDD Note
Power-down Base Current (IPD)(2)
D023 0.06 1.0 8.0 A 1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
0.08 2.0 9.0 A3.0
D023 21 55 63 A1.8 WDT, BOR, FVR, and T1OSC
disabled, all Peripherals Inactive
25 58 78 A3.0
27 60 88 A5.0
D024 0.5 4.0 9.0 A 1.8 LPWDT Current (Note 1)
—0.85.0 10 A3.0
D024 23 57 65 A1.8 LPWDT Current (Note 1)
26 59 80 A3.0
28 61 90 A5.0
D025 15 28 30 A 1.8 FVR current
—15 30 33 A3.0
D025 38 96 100 A1.8 FVR current (Note 4 )
45 110 120 A3.0
90 140 155 A5.0
D026 13 25 28 A 3.0 BOR Current (Note 1)
D026 40 110 120 A3.0 BOR Current (Note 1, Note 4)
87 140 155 A5.0
D027 0.6 5.0 9.0 A 1.8 T1OSC Current (Note 1)
—1.87.0 12 A3.0
D027 22 57 60 A1.8 T1OSC Current (Note 1)
29 62 70 A3.0
35 66 85 A5.0
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
4: 0.1 F capacitor on VCAP (RA0).
PIC16(L)F1934/6/7
DS41364E-page 388 2008-2011 Microchip Technology Inc.
Power-down Base Current (IPD)(2)
D028 0.1 4.0 8.0 A 1.8 A/D Current (Note 1, Note 3), no
conversion in progress
0.1 5.0 9.0 A3.0
D028 22 56 63 A1.8 A/D Current (Note 1, Note 3), no
conversion in progress
26 58 78 A3.0
27 61 88 A5.0
D029 250 A 1.8 A/D Current (Note 1, Note 3),
conversion in progress
—250 A3.0
D029 280 A1.8 A/D Current (Note 1, Note 3,
Note 4), conversion in progress
280 A3.0
280 A5.0
D030 2 7 11 A 1.8 Cap Sense, Low-Power mode
—3 9 13A3.0
D030 21 61 63 A1.8 Cap Sense, Low-Power mode
27 63 78 A3.0
28 66 88 A5.0
D031 1 A 3.0 LCD Bias Ladder, Low-power
—10 A 3.0 LCD Bias Ladder, Medium-power
—75 A 3.0 LCD Bias Ladder, High-power
D031 1 A5.0 LCD Bias Ladder, Low-power
10 A5.0 LCD Bias Ladder, Medium-power
75 A5.0 LCD Bias Ladder, High-power
D032 7.6 22 25 A 1.8 Comparator, Low-Power mode
8.0 23 27 A3.0
D032 24 65 75 A1.8 Comparator, Low-Power mode
26 75 88 A3.0
28 77 97 A5.0
30.3 DC Characteristics: PIC16(L)F1934/6/7-I/E (Power-Down) (Continued )
PIC16LF1934/36/37 Standard Operati ng Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
PIC16F1934/36/37 Standard Operating Condition s (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Device Characteristics Min. Typ† Max.
+85°C Max.
+125°C Units Conditions
VDD Note
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
4: 0.1 F capacitor on VCAP (RA0).
2008-2011 Microchip Technology Inc. DS41364E-page 389
PIC16(L)F1934/6/7
30.4 DC Characteristics: PIC16(L)F1934/6/7-I/E
DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
VIL Input L ow Voltage
I/O PORT:
D032 with TTL buffer 0.8 V 4.5V VDD 5.5V
D032A 0.15 VDD V1.8V VDD 4.5V
D033 with Schmitt Trigger buffer 0.2 VDD V2.0V VDD 5.5V
with I2C™ levels 0.3 VDD V
with SMBus levels 0.8 V 2.7V VDD 5.5V
D034 MCLR, OSC1 (RC mode)(1) ——0.2VDD V
D034A OSC1 (HS mode) 0.3 VDD V
VIH Input High Voltage
I/O ports:
D040 with TTL buffer 2.0 V 4.5V VDD 5.5V
D040A 0.25 VDD +
0.8
——V1.8V VDD 4.5V
D041 with Schmitt Trigger buffer 0.8 VDD ——V2.0V VDD 5.5V
with I2C™ levels 0.7 VDD ——V
with SMBus levels 2.1 V 2.7V VDD 5.5V
D042 MCLR 0.8 VDD ——V
D043A OSC1 (HS mode) 0.7 VDD ——V
D043B OSC1 (RC mode) 0.9 VDD ——VVDD 2.0V (Note 1)
IIL Input Leakage Current(2)
D060 I/O ports ± 5
± 5
± 125
± 1000
nA
nA
VSS VPIN VDD, Pin at high-
impedance @ 85°C
125°C
D061 MCLR(3) —± 50± 200nAVSS VPIN VDD @ 85°C
IPUR Weak Pull-up Current
D070* 25
25
100
140
200
300 A
VDD = 3.3V, VPIN = VSS
VDD = 5.0V, VPIN = VSS
VOL Output Low Volta ge(4)
D080 I/O ports
——0.6V
IOL = 8mA, VDD = 5V
IOL = 6mA, VDD = 3.3V
IOL = 1.8mA, VDD = 1.8V
VOH Output High Volta ge (4)
D090 I/O ports
VDD - 0.7 V
IOH = 3.5mA, VDD = 5V
IOH = 3mA, VDD = 3.3V
IOH = 1mA, VDD = 1.8V
Capacitive Loading Specs on Output Pins
D101* COSC2 OSC2 pin 15 pF In XT, HS and LP modes when
external clock is used to drive
OSC1
D101A* CIO All I/O pins 50 pF
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
4: Including OSC2 in CLKOUT mode.
PIC16(L)F1934/6/7
DS41364E-page 390 2008-2011 Microchip Technology Inc.
VCAP Capacitor Charging
D102 Charging current 200 A
D102A Source/sink capability when
charging complete
—0.0mA
30.4 DC Characteristics: PIC16(L)F1934/6/7-I/E (Continued)
DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +85°C for industrial
-40°C TA +125°C for extended
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: In RC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended to use an external
clock in RC mode.
2: Negative current is defined as current sourced by the pin.
3: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
4: Including OSC2 in CLKOUT mode.
2008-2011 Microchip Technology Inc. DS41364E-page 391
PIC16(L)F1934/6/7
30.5 Memory Programming Requirements
DC CHARACTERISTICS Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
Program Memory
Program m in g Speci fic at ion s
D110 VIHH Voltage on MCLR/VPP/RE3 pin 8.0 9.0 V (Note 3, Note 4)
D111 IDDP Supply Current during
Programming
——10mA
D112 VDD for Bulk Erase 2.7 VDD
max.
V
D113 VPEW VDD for Write or Row Erase VDD
min.
—V
DD
max.
V
D114 IPPPGM Current on MCLR/VPP during Erase/
Write
——1.0mA
D115 IDDPGM Current on VDD during Erase/Write 5.0 mA
Data EEPROM Memory
D116 EDByte Endurance 100K —E/W-40C to +85C
D117 VDRW VDD for Read/Write VDD
min.
—V
DD
max.
V
D118 TDEW Erase/Write Cycle Time 4.0 5.0 ms
D119 TRETD Characteristic Retention 40 Year Provided no other
specifications are violated
D120 TREF Number of Total Erase/Write
Cycles before Refresh(2) 1M 10M E/W -40°C to +85°C
Program Flash Memory
D121 EPCell Endurance 10K —E/W-40C to +85C (Note 1)
D122 VPR VDD for Read VDD
min.
—V
DD
max.
V
D123 TIW Self-timed Write Cycle Time 2 2.5 ms
D124 TRETD Characteristic Retention 40 Year Provided no other
specifications are violated
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: Self-write and Block Erase.
2: Refer to Section 11.2 “Using the Data EEPROM” for a more detailed discussion on data EEPROM
endurance.
3: Required only if single-supply programming is disabled.
4: The MPLAB ICD 2 does not support variable VPP output. Circuitry to limit the ICD 2 VPP voltage must be
placed between the ICD 2 and target system when programming or debugging with the ICD 2.
PIC16(L)F1934/6/7
DS41364E-page 392 2008-2011 Microchip Technology Inc.
30.6 Thermal Considerations
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +125°C
Param
No. Sym. Characteristic Typ. Units Conditions
TH01 JA Thermal Resistance Junction to Ambient 60 C/W 28-pin SPDIP package
80 C/W 28-pin SOIC package
90 C/W 28-pin SSOP package
27.5 C/W 28-pin UQFN 4x4mm package
27.5 C/W 28-pin QFN 6x6mm package
47.2 C/W 40-pin PDIP package
46 C/W 44-pin TQFP package
24.4 C/W 44-pin QFN 8x8mm package
TH02 JC Thermal Resistance Junction to Case 31.4 C/W 28-pin SPDIP package
24 C/W 28-pin SOIC package
24 C/W 28-pin SSOP package
24 C/W 28-pin UQFN 4x4mm package
24 C/W 28-pin QFN 6x6mm package
24.7 C/W 40-pin PDIP package
14.5 C/W 44-pin TQFP package
20 C/W 44-pin QFN 8x8mm package
TH03 TJMAX Maximum Junction Temperature 150 C
TH04 PD Power Dissipation W PD = PINTERNAL + PI/O
TH05 PINTERNAL Internal Power Dissipation W PINTERNAL = IDD x VDD(1)
TH06 PI/OI/O Power Dissipation W PI/O = (IOL * VOL) + (IOH * (VDD - VOH))
TH07 PDER Derated Power W PDER = PDMAX (TJ - TA)/JA(2)
Note 1: IDD is current to run the chip alone without driving any load on the output pins.
2: TA = Ambient Temperature
3: TJ = Junction Temperature
2008-2011 Microchip Technology Inc. DS41364E-page 393
PIC16(L)F1934/6/7
30.7 Timing Parameter Symbology
The timing parameter symbols have been created with
one of the following formats:
FIGURE 30-5: LOAD CONDITIONS
1. TppS2ppS
2. TppS
T
F Frequency T Time
Lowercase letters (pp) and their meanings:
pp
cc CCP1 osc OSC1
ck CLKOUT rd RD
cs CS rw RD or WR
di SDI sc SCK
do SDO ss SS
dt Data in t0 T0CKI
io I/O PORT t1 T1CKI
mc MCLR wr WR
Uppercase letters and their meanings:
S
FFall PPeriod
HHigh RRise
I Invalid (High-impedance) V Valid
L Low Z High-impedance
V
SS
C
L
Legend: CL = 50 pF for all pins, 15 pF for
OSC2 output
Load Condition
Pin
PIC16(L)F1934/6/7
DS41364E-page 394 2008-2011 Microchip Technology Inc.
30.8 AC Characteristics: PIC16(L)F1934/6/7- I/E
FIGURE 30-6: CLOCK TIMING
TABLE 30-1: CLOCK OSCILLATOR TIMING REQUIREMENTS
OSC1/CLKIN
OSC2/CLKOUT
Q4 Q1 Q2 Q3 Q4 Q1
OS02
OS03
OS04 OS04
OSC2/CLKOUT
(LP,XT,HS Modes)
(CLKOUT Mode)
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
OS01 FOSC External CLKIN Frequency(1) DC 0.5 MHz EC Oscillator mode (low)
DC 4 MHz EC Oscillator mode (medium)
DC 20 MHz EC Oscillator mode (high)
Oscillator Frequency(1) 32.768 kHz LP Oscillator mode
0.1 4 MHz XT Oscillator mode
1 4 MHz HS Oscillator mode
1 20 MHz HS Oscillator mode, VDD > 2.7V
DC 4 MHz RC Oscillator mode, VDD 2.0V
OS02 TOSC External CLKIN Period(1) 27 s LP Oscillator mode
250 ns XT Oscillator mode
50 ns HS Oscillator mode
50 ns EC Oscillator mode
Oscillator Period(1) 30.5 s LP Oscillator mode
250 10,000 ns XT Oscillator mode
50 1,000 ns HS Oscillator mode
250 ns RC Oscillator mode
OS03 TCY Instruction Cycle Time(1) 200 TCY DC ns TCY = 4/FOSC
OS04* TosH,
TosL
External CLKIN High,
External CLKIN Low
2—s LP oscillator
100 ns XT oscillator
20 ns HS oscillator
OS05* TosR,
TosF
External CLKIN Rise,
External CLKIN Fall
0—ns LP oscillator
0—ns XT oscillator
0—ns HS oscillator
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (T
CY) equals four times the input oscillator time base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at “min” values with an external clock applied to OSC1 pin. When an external
clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
2008-2011 Microchip Technology Inc. DS41364E-page 395
PIC16(L)F1934/6/7
TABLE 30-2: OSCILLATOR PARAMETERS
TABLE 30-3: PLL CLOCK TIMING SPECIFICATIONS (VDD = 2.7V TO 5.5V)
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param
No. Sym. Characteristic Freq.
Tolerance Min. Typ† Max. Units Conditions
OS08 HFOSC Internal Calibrated HFINTOSC
Frequency(2) ±2%
±3%
16.0
16.0
MHz
MHz
0°C TA +60°C, VDD 2.5V
60°C T
A 85°C, VDD 2.5V
±5% 16.0 MHz -40°C TA +125°C
OS08A MFOSC Internal Calibrated MFINTOSC
Frequency(2) ±2%
±3%
500
500
kHz
kHz
0°C TA +60°C, VDD 2.5V
60°C T
A 85°C, VDD 2.5V
±5% 500 kHz -40°C TA +125°C
OS09 LFOSC Internal LFINTOSC Frequency 31 kHz -40°C TA +125°C
OS10* TIOSC ST HFINTOSC
Wake-up from Sleep Start-up Time
MFINTOSC
Wake-up from Sleep Start-up Time
——3.28s
24 35 s
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are based on
characterization data for that particular oscillator type under standard operating conditions with the device executing code.
Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current con-
sumption. All devices are tested to operate at “min” values with an external clock applied to the OSC1 pin. When an exter-
nal clock input is used, the “max” cycle time limit is “DC” (no clock) for all devices.
2: To ensure these oscillator frequency tolerances, VDD and VSS must be capacitively decoupled as close to the device as
possible. 0.1 F and 0.01 F values in parallel are recommended.
3: By design.
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
F10 FOSC Oscillator Frequency Range 4 8 MHz
F11 FSYS On-Chip VCO System Frequency 16 32 MHz
F12 TRC PLL Start-up Time (Lock Time) 2 ms
F13* CLK CLKOUT Stability (Jitter) -0.25% +0.25% %
* These parameters are characterized but not tested.
Data in “Typ” column is at 5V, 25C unless otherwise stated. These parameters are for design guidance
only and are not tested.
PIC16(L)F1934/6/7
DS41364E-page 396 2008-2011 Microchip Technology Inc.
FIGURE 30-7: CLKOUT AND I/O TIMING
FOSC
CLKOUT
I/O pin
(Input)
I/O pin
(Output)
Q4 Q1 Q2 Q3
OS11
OS19
OS13
OS15
OS18, OS19
OS20
OS21
OS17
OS16
OS14
OS12
OS18
Old Value New Value
Write Fetch Read ExecuteCycle
2008-2011 Microchip Technology Inc. DS41364E-page 397
PIC16(L)F1934/6/7
TABLE 30-4: CLKOUT AND I/O TIMING PARAMETERS
FIGURE 30-8: RESET, WATCHDOG TIMER, OSCILLATOR ST ART-UP TIMER AND POWER-UP
TIMER TIMI NG
S tandard Operating Conditi ons (unle ss othe rwis e stated)
Operating Temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
OS11 TosH2ckL FOSC to CLKOUT (1) ——70nsVDD = 3.3-5.0V
OS12 TosH2ckH FOSC to CLKOUT (1) ——72nsVDD = 3.3-5.0V
OS13 TckL2ioV CLKOUT to Port out valid(1) ——20ns
OS14 TioV2ckH Port input valid before CLKOUT(1) TOSC + 200 ns ns
OS15 TosH2ioV Fosc (Q1 cycle) to Port out valid 50 70* ns VDD = 3.3-5.0V
OS16 TosH2ioI Fosc (Q2 cycle) to Port input invalid
(I/O in hold time)
50 ns VDD = 3.3-5.0V
OS17 TioV2osH Port input valid to Fosc(Q2 cycle)
(I/O in setup time)
20 ns
OS18 TioR Port output rise time
40
15
72
32
ns VDD = 1.8V
VDD = 3.3-5.0V
OS19 TioF Port output fall time
28
15
55
30
ns VDD = 1.8V
VDD = 3.3-5.0V
OS20* Tinp INT pin input high or low time 25 ns
OS21* Tioc Interrupt-on-change new input level
time
25 ns
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25C unless otherwise stated.
Note1: Measurements are taken in RC mode where CLKOUT output is 4 x TOSC.
VDD
MCLR
Internal
POR
PWRT
Time-out
OSC
Start-Up Time
Internal Reset(1)
Watchdog Timer
33
32
30
31
34
I/O pins
34
Note 1: Asserted low.
Reset(1)
PIC16(L)F1934/6/7
DS41364E-page 398 2008-2011 Microchip Technology Inc.
FIGURE 30-9: BROWN-OUT RESET TIMING AND CHARACTERISTICS
VBOR
VDD
(Device in Brown-out Reset) (Device not in Brown-out Reset)
33(1)
Note 1: 64 ms delay only if PWRTE bit in the Configuration Word register is programmed to 0’.
2 ms delay if PWRTE = 0 and VREGEN = 1.
Reset
(due to BOR)
VBOR and VHYST
37
2008-2011 Microchip Technology Inc. DS41364E-page 399
PIC16(L)F1934/6/7
TABLE 30-5: RESET, WATCHDOG TIMER, OSCILLATOR ST ART-UP TIMER, POWER-UP TIMER
AND BROWN-OUT RESET PARAMETERS
FIGURE 30-10: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
30 TMCLMCLR Pulse Width (low) 2 s
31 TWDTLP Low-Power Watchdog Timer
Time-out Period
10 16 27 ms VDD = 3.3V-5V
1:16 Prescaler used
32 TOST Oscillator Start-up Timer Period(1), (2) 1024 Tosc (Note 3)
33* TPWRT Power-up Timer Period, PWRTE =040 65 140 ms
34* TIOZ I/O high-impedance from MCLR Low
or Watchdog Timer Reset
——2.0s
35 VBOR Brown-out Reset Voltage 2.38
1.80
2.5
1.9
2.73
2.11
VBORV=2.5V
BORV=1.9V
36* VHYST Brown-out Reset Hysteresis 0 25 60 mV -40°C to +85°C
37* TBORDC Brown-out Reset DC Response
Time
1335sVDD VBOR
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note1: Instruction cycle period (TCY) equals four times the input oscillator time base period. All specified values are
based on characterization data for that particular oscillator type under standard operating conditions with the
device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or
higher than expected current consumption. All devices are tested to operate at “min” values with an external
clock applied to the OSC1 pin. When an external clock input is used, the “max” cycle time limit is “DC” (no
clock) for all devices.
2: By design.
3: Period of the slower clock.
4: To ensure these voltage tolerances, VDD and VSS must be capacitively decoupled as close to the device as
possible. 0.1 F and 0.01 F values in parallel are recommended.
T0CKI
T1CKI
40 41
42
45 46
47 49
TMR0 or
TMR1
PIC16(L)F1934/6/7
DS41364E-page 400 2008-2011 Microchip Technology Inc.
TABLE 30-6: TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
FIGURE 30-11: CAPTURE/COM PARE/PWM TIMINGS (CCP)
TABLE 30-7: CAPTURE/COMPARE/PWM REQUIREMENTS (CCP)
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
40* TT0H T0CKI High Pulse Width No Prescaler 0.5 TCY + 20 ns
With Prescaler 10 ns
41* TT0L T0CKI Low Pulse Width No Prescaler 0.5 TCY + 20 ns
With Prescaler 10 ns
42* TT0P T0CKI Period Greater of:
20 or TCY + 40
N
ns N = prescale value
(2, 4, ..., 256)
45* TT1H T1CKI High
Time
Synchronous, No Prescaler 0.5 TCY + 20 ns
Synchronous,
with Prescaler
15 ns
Asynchronous 30 ns
46* TT1L T1CKI Low
Time
Synchronous, No Prescaler 0.5 TCY + 20 ns
Synchronous, with Prescaler 15 ns
Asynchronous 30 ns
47* TT1P T1CKI Input
Period
Synchronous Greater of:
30 or TCY + 40
N
ns N = prescale value
(1, 2, 4, 8)
Asynchronous 60 ns
48 FT1 Timer1 Oscillator Input Frequency Range
(oscillator enabled by setting bit T1OSCEN)
32.4 32.768 33.1 kHz
49* TCKEZTMR1 Delay from External Clock Edge to Timer
Increment
2 TOSC —7 TOSC Timers in Sync
mode
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
CC01* TccL CCPx Input Low Time No Prescaler 0.5TCY + 20 ns
With Prescaler 20 ns
CC02* TccH CCPx Input High Time No Prescaler 0.5TCY + 20 ns
With Prescaler 20 ns
CC03* TccP CCPx Input Period 3TCY + 40
N
ns N = prescale value (1, 4 or 16)
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note: Refer to Figure 30-5 for load conditions.
(Capture mode)
CC01 CC02
CC03
CCPx
2008-2011 Microchip Technology Inc. DS41364E-page 401
PIC16(L)F1934/6/7
TABLE 30-8: PIC16(L)F1934/6/7 A/D CONVERTER (ADC) CHARACTERISTICS:
TABLE 30-9: PIC16(L)F1934/6/7 A/D CONVERSION REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating temperature Tested at 25°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
AD01 NRResolution 10 bit
AD02 EIL Integral Error ±1.7 LSb VREF = 3.0V
AD03 EDL Differential Error ±1 LSb No missing codes
VREF = 3.0V
AD04 EOFF Offset Error ±2.5 LSb VREF = 3.0V
AD05 EGN Gain Error ±2.0 LSb VREF = 3.0V
AD06 VREF Reference Voltage(3) 1.8 VDD VVREF = (VREF+ minus VREF-) (Note 5)
AD07 VAIN Full-Scale Range VSS —VREF V
AD08 ZAIN Recommended Impedance of
Analog Voltage Source
—— 10
kCan go higher if external 0.01F capacitor is
present on input pin.
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: Total Absolute Error includes integral, differential, offset and gain errors.
2: The A/D conversion result never decreases with an increase in the input voltage and has no missing codes.
3: ADC VREF is from external VREF, VDD pin or FVR, whichever is selected as reference input.
4: When ADC is off, it will not consume any current other than leakage current. The power-down current specification
includes any such leakage from the ADC module.
5: FVR voltage selected must be 2.048V or 4.096V.
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C TA +125°C
Param
No. Sym. Characteristic Min. Typ† Max. Units Conditions
AD130* TAD A/D Clock Period 1.0 9.0 sTOSC-based
A/D Internal RC Oscillator
Period
1.0 2.5 6.0 s ADCS<1:0> = 11 (ADRC mode)
AD131 TCNV Conversion Time (not including
Acquisition Time)(1) —11—TAD Set GO/DONE bit to conversion
complete
AD132* TACQ Acquisition Time 5.0 s
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The ADRES register may be read on the following TCY cycle.
PIC16(L)F1934/6/7
DS41364E-page 402 2008-2011 Microchip Technology Inc.
FIGURE 30-12: PIC16(L)F1934/6/7 A/D CONVERSION TIMING (NORMAL MODE)
FIGURE 30-13: PIC16(L)F1934/6/7 A/D CONVERSION TIMING (SLEEP MODE)
AD131
AD130
BSF ADCON0, GO
Q4
A/D CLK
A/D Data
ADRES
ADIF
GO
Sample
OLD_DATA
Sampling Stopped
DONE
NEW_DATA
765 3210
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the
SLEEP instruction to be executed.
1 TCY
4
AD134 (TOSC/2(1))
1 TCY
AD132
AD132
AD131
AD130
BSF ADCON0, GO
Q4
A/D CLK
A/D Data
ADRES
ADIF
GO
Sample
OLD_DATA
Sampling Stopped
DONE
NEW_DATA
7 5 3210
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the
SLEEP instruction to be executed.
AD134
4
6
1 TCY
(TOSC/2 + TCY(1))
1 TCY
2008-2011 Microchip Technology Inc. DS41364E-page 403
PIC16(L)F1934/6/7
TABLE 30-10: COMPARATOR SPECIFICATIONS
TABLE 30-11: DIGITAL-TO-ANALOG CONVERTER (DAC) SPECIFICATIONS
FIGURE 30-14: USART SYNCHRONOUS TRANSMISSION (MASTER/SLAVE) TIMING
Operating Conditions: 1.8V < VDD < 5.5V, -40°C < TA < +125°C (unless otherwise stated).
Param
No. Sym. Characteristics Min. Typ. Max. Units Comments
CM01 VIOFF Input Offset Voltage ±7.5 ±60 mV High-Power mode
CM02 VICM Input Common Mode Voltage 0 VDD V
CM03 CMRR Common Mode Rejection Ratio 50 dB
CM04A
TRESP
Response Time Rising Edge 400 800 ns High-Power mode
CM04B Response Time Falling Edge 200 400 ns High-Power mode
CM04C Response Time Rising Edge 1200 ns Low-Power mode
CM04D Response Time Falling Edge 550 ns Low-Power mode
CM05 TMC2OV Comparator Mode Change to
Output Valid*
——10s
CM06 CHYSTER Comparator Hysteresis 45 mV Hysteresis on
* These parameters are characterized but not tested.
Note 1: Response time measured with one comparator input at VDD/2, while the other input transitions
from VSS to VDD.
2: Comparator Hysteresis is available when the CxHYS bit of the CMxCON0 register is enabled.
Operating Condit ions : 2.5V < VDD < 5.5V, -40°C < TA < +125°C (unless otherwise stated).
Param
No. Sym. Characteristics Min. Typ. Max. Units Comments
DAC01* CLSB Step Size VDD/32 V
DAC02* CACC Absolute Accuracy 1/2 LSb
DAC03* CRUnit Resistor Value (R) 5000
DAC04* CST Settling Time(1) ——10s
* These parameters are characterized but not tested.
Note 1: Settling time measured while DACR<4:0> transitions from ‘0000’ to1111’.
Note: Refer to Figure 30-5 for load conditions.
US121 US121
US120 US122
CK
DT
PIC16(L)F1934/6/7
DS41364E-page 404 2008-2011 Microchip Technology Inc.
TABLE 30-12: USART SYNCHRONOUS TRANSMISSION REQUIREMENT S
FIGURE 30-15: USART SYNCHRONOUS RECEIVE (MASTER/SLAVE) TIMING
TABLE 30-13: USART SYNCHRONOUS RECEIVE REQUIREMENTS
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param.
No. Symbol Characteristic Min. Max. Units Conditions
US120 TCKH2DTV SYNC XMIT (Master and Slave)
Clock high to data-out valid
3.0-5.5V 80 ns
1.8-5.5V 100 ns
US121 TCKRF Clock out rise time and fall time
(Master mode)
3.0-5.5V 45 ns
1.8-5.5V 50 ns
US122 TDTRF Data-out rise time and fall time 3.0-5.5V 45 ns
1.8-5.5V 50 ns
Standard Operating Conditions (unless otherwise stated)
Operating Temperature -40°C TA +125°C
Param.
No. Symbol Characteristic Min. Max. Units Conditions
US125 TDTV2CKL SYNC RCV (Master and Slave)
Data-hold before CK (DT hold time) 10 ns
US126 T
CKL2DTL Data-hold after CK (DT hold time) 15 ns
Note: Refer to Figure 30-5 for load conditions.
US125
US126
CK
DT
2008-2011 Microchip Technology Inc. DS41364E-page 405
PIC16(L)F1934/6/7
FIGURE 30-16 : SP I MAST E R MODE TIMING (CKE = 0, SMP = 0)
FIGURE 30-17 : SP I MAST E R MODE TIMING (CKE = 1, SMP = 1)
SS
SCK
(CKP = 0)
SCK
(CKP = 1)
SDO
SDI
SP70
SP71 SP72
SP73
SP74
SP75, SP76
SP78
SP79
SP80
SP79
SP78
MSb LSb
bit 6 - - - - - -1
MSb In LSb In
bit 6 - - - -1
Note: Refer to Figure 30-5 for load conditions.
SS
SCK
(CKP = 0)
SCK
(CKP = 1)
SDO
SDI
SP81
SP71 SP72
SP74
SP75, SP76
SP78
SP80
MSb
SP79
SP73
MSb In
bit 6 - - - - - -1
LSb In
bit 6 - - - -1
LSb
Note: Refer to Figure 30-5 for load conditions.
PIC16(L)F1934/6/7
DS41364E-page 406 2008-2011 Microchip Technology Inc.
FIGURE 30-18 : SPI SL AVE MODE TIMING (CKE = 0)
FIGURE 30-19 : SPI SL AVE MODE TIMING (CKE = 1)
SS
SCK
(CKP = 0)
SCK
(CKP = 1)
SDO
SDI
SP70
SP71 SP72
SP73
SP74
SP75, SP76 SP77
SP78
SP79
SP80
SP79
SP78
MSb LSb
bit 6 - - - - - -1
MSb In bit 6 - - - -1 LSb In
SP83
Note: Refer to Figure 30-5 for load conditions.
SS
SCK
(CKP = 0)
SCK
(CKP = 1)
SDO
SDI
SP70
SP71 SP72
SP82
SP74
SP75, SP76
MSb bit 6 - - - - - -1 LSb
SP77
MSb In bit 6 - - - -1 LSb In
SP80
SP83
Note: Refer to Figure 30-5 for load conditions.
2008-2011 Microchip Technology Inc. DS41364E-page 407
PIC16(L)F1934/6/7
TABLE 30-14: SPI MODE REQUIREMENTS
FIGURE 30-20 : I2C™ BUS STAR T/STOP BITS TIMING
Param
No. Symbol Characteristic Min. Typ† Max. Units Conditions
SP70* TSSL2SCH,
TSSL2SCL
SS to SCK or SCK input TCY ——ns
SP71* TSCH SCK input high time (Slave mode) TCY + 20 ns
SP72* TSCL SCK input low time (Slave mode) TCY + 20 ns
SP73* TDIV2SCH,
TDIV2SCL
Setup time of SDI data input to SCK edge 100 ns
SP74* TSCH2DIL,
TSCL2DIL
Hold time of SDI data input to SCK edge 100 ns
SP75* TDOR SDO data output rise time 3.0-5.5V 10 25 ns
1.8-5.5V 25 50 ns
SP76* TDOF SDO data output fall time 10 25 ns
SP77* TSSH2DOZSS to SDO output high-impedance 10 50 ns
SP78* TSCR SCK output rise time
(Master mode)
3.0-5.5V 10 25 ns
1.8-5.5V 25 50 ns
SP79* TSCF SCK output fall time (Master mode) 10 25 ns
SP80* TSCH2DOV,
TSCL2DOV
SDO data output valid after
SCK edge
3.0-5.5V 50 ns
1.8-5.5V 145 ns
SP81* TDOV2SCH,
TDOV2SCL
SDO data output setup to SCK edge Tcy ns
SP82* TSSL2DOV SDO data output valid after SS edge 50 ns
SP83* TSCH2SSH,
TSCL2SSH
SS after SCK edge 1.5TCY + 40 ns
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note: Refer to Figure 30-5 for load conditions.
SP91
SP92
SP93
SCL
SDA
Start
Condition
Stop
Condition
SP90
PIC16(L)F1934/6/7
DS41364E-page 408 2008-2011 Microchip Technology Inc.
TABLE 30-15: I2C™ BUS START/STOP BITS REQUIREMENTS
FIGURE 30-21 : I2C™ BUS DATA TIMING
Param
No. Symbol Characteristic Min. Typ Max. Units Conditions
SP90* TSU:STA Start condition 100 kHz mode 4700 ns Only relevant for Repeated
Start condition
Setup time 400 kHz mode 600
SP91* THD:STA Start condition 100 kHz mode 4000 ns After this period, the first
clock pulse is generated
Hold time 400 kHz mode 600
SP92* TSU:STO Stop condition 100 kHz mode 4700 ns
Setup time 400 kHz mode 600
SP93 THD:STO Stop condition 100 kHz mode 4000 ns
Hold time 400 kHz mode 600
* These parameters are characterized but not tested.
Note: Refer to Figure 30-5 for load conditions.
SP90
SP91 SP92
SP100
SP101
SP103
SP106 SP107
SP109 SP109
SP110
SP102
SCL
SDA
In
SDA
Out
2008-2011 Microchip Technology Inc. DS41364E-page 409
PIC16(L)F1934/6/7
TABLE 30-16: I2C™ BUS DATA REQUIREM ENTS
Param.
No. Symbol Characteristic Min. Max. Units Conditions
SP100* THIGH Clock high time 100 kHz mode 4.0 s Device must operate at a
minimum of 1.5 MHz
400 kHz mode 0.6 s Device must operate at a
minimum of 10 MHz
SSP module 1.5TCY
SP101* TLOW Clock low time 100 kHz mode 4.7 s Device must operate at a
minimum of 1.5 MHz
400 kHz mode 1.3 s Device must operate at a
minimum of 10 MHz
SSP module 1.5TCY
SP102* TRSDA and SCL rise
time
100 kHz mode 1000 ns
400 kHz mode 20 + 0.1CB300 ns CB is specified to be from
10-400 pF
SP103* TFSDA and SCL fall
time
100 kHz mode 250 ns
400 kHz mode 20 + 0.1CB250 ns CB is specified to be from
10-400 pF
SP106* THD:DAT Data input hold time 100 kHz mode 0 ns
400 kHz mode 0 0.9 s
SP107* TSU:DAT Data input setup
time
100 kHz mode 250 ns (Note 2)
400 kHz mode 100 ns
SP109* TAA Output valid from
clock
100 kHz mode 3500 ns (Note 1)
400 kHz mode ns
SP110* TBUF Bus free time 100 kHz mode 4.7 s Time the bus must be free
before a new transmission
can start
400 kHz mode 1.3 s
SP111 CBBus capacitive loading 400 pF
* These parameters are characterized but not tested.
Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region
(min. 300 ns) of the falling edge of SCL to avoid unintended generation of Start or Stop conditions.
2: A Fast mode (400 kHz) I2C bus device can be used in a Standard mode (100 kHz) I2C bus system, but
the requirement T
SU:DAT 250 ns must then be met. This will automatically be the case if the device does
not stretch the low period of the SCL signal. If such a device does stretch the low period of the SCL signal,
it must output the next data bit to the SDA line TR max. + TSU:DAT = 1000 + 250 = 1250 ns (according to
the Standard mode I2C bus specification), before the SCL line is released.
PIC16(L)F1934/6/7
DS41364E-page 410 2008-2011 Microchip Technology Inc.
TABLE 30-17: CAP SENSE OSCILLATOR SPECIFICATIONS
FIGURE 30-22: CAP SENSE OSCILLATOR
Param.
No. Symbol Characteristic Min. Typ† Max. Units Conditions
CS01 ISRC Current Source High -3 -8 -15 A
Medium -0.8 -1.5 -3 A
Low -0.1 -0.3 -0.4 A
CS02 ISNK Current Sink High 2.5 7.5 14 A
Medium 0.6 1.5 2.9 A
Low 0.1 0.25 0.6 A
CS03 VCTH Cap Threshold 0.8 mV
CS04 VCTL Cap Threshold 0.4 mV
CS05 VCHYST Cap Hysteresis
(VCTH-VCTL)
High
Medium
Low
350
250
175
525
375
300
725
500
425
mV
mV
mV
* These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
ISRC
VCTH
VCTL
ISNK
EnabledEnabled
2008-2011 Microchip Technology Inc. DS41364E-page 411
PIC16(L)F1934/6/7
31.0 DC AND AC CHARACTERISTICS GRAPHS AND CHARTS
FIGURE 31-1: PIC16F1934/6/7 RESET VOLTAGE, BOR = 1.9V
FIGURE 31-2: PIC16F1934/6/7 HYSTERESIS, BOR = 1.9V
1.800
1.850
1.900
1.950
2.000
2.050
2.100
-40°C 25°C 85°C 125°C
Max.
Min.
Voltage (V)
Temperature (
Celsius)
Max.: High Power + 3
Min.: Low Power -3
Typical
Min.
Max.
0
0.005
0.01
0.015
0.02
0.025
0.03
0.035
-40°C 25°C 85°C 125°C
Voltage (V)
Temperature
(Celsius)
Max.: Typical + 3
Min.: Typical -3
PIC16(L)F1934/6/7
DS41364E-page 412 2008-2011 Microchip Technology Inc.
FIGURE 31-3: PIC16F1934/6/7 RESET VOLTAGE, BOR = 2.5V
FIGURE 31-4: PIC16F1934/6/7 HYSTERESIS, BOR = 2.5V
2.350
2.400
2.450
2.500
2.550
2.600
2.650
-40°C 25°C 85°C 125°C
Max.
Min.
Voltage (V)
Temperature
(Celsius)
Max.: High Power + 3
Min.: Low Power -3
Typical
Min.
Max.
0
0.01
0.02
0.03
0.04
0.05
0.06
-40°C 25°C 85°C 125°C
Voltage (V)
Temperature
(Celsius)
Max.: Typical + 3
Min.: Typical -3
2008-2011 Microchip Technology Inc. DS41364E-page 413
PIC16(L)F1934/6/7
FIGURE 31-5: PIC16F1934/6/7 POR RELEASE
FIGURE 31-6: PIC16F19 34/ 6/7 COMPARATOR HYSTERESIS, HIGH-POWER MODE
Typical
Min.
Max.
1.5
1.52
1.54
1.56
1.58
1.6
1.62
1.64
1.66
1.68
1.7
-40°C 25°C 85°C 125°C
Release Voltage (V)
Temperature
(Celsius)
Max.: Maximum + 3
Min.: Minimum -3
Min: -40°C
Typical: 25°C
Max.: 125°C
0
10
20
30
40
50
60
70
80
90
1.8 3 3.6 5.5
Hysteresis (mV)
VDD (V)
Max.: Maximum + 3
Min.: Minimum -3
PIC16(L)F1934/6/7
DS41364E-page 414 2008-2011 Microchip Technology Inc.
FIGURE 31-7: PIC16F19 34/ 6/7 COMPARATOR HYSTERESIS, LOW-POWER MODE
FIGURE 31-8: PIC16F19 34/ 6/7 COMPARATOR OFFSET, HIGH-POWER MODE, VDD = 5.5V
Min.: -40°C
Typical: 25°C
Max.: 125°C
0
2
4
6
8
10
12
14
16
1.8 5.5
Hysteresis (mV)
VDD (V)
Max.: Maximum + 3
Min.: Minimum -3
Max.
Typical
Min.
-60
-40
-20
0
20
40
60
0.2 1 1.8 2.6 3.4 4.2 5
Offset (mV)
Common Mode Voltage (V)
Max.: Maximum + 3
Min.: Minimum -3
2008-2011 Microchip Technology Inc. DS41364E-page 415
PIC16(L)F1934/6/7
FIGURE 31-9: PIC16F1934/ 6/7 C OMPARATOR RESPONSE TIME, HIGH-POWER MODE
FIGURE 31-10: TYPICAL COMPARATOR RESPONSE TIME OVER TEMPERATURE,
HIGH-POWER MODE
Typical
Max.
0
50
100
150
200
250
300
350
1.8 2 2.5 3 3.6 5.5
Tim e (nSeconds)
VDD (V)
Max.: Maximum + 3
Min.: Minimum -3
-40°C
25°C
85°C
125°C
135
140
145
150
155
160
165
170
1.822.533.65.5
Time (nSeconds)
VDD (V)
PIC16(L)F1934/6/7
DS41364E-page 416 2008-2011 Microchip Technology Inc.
FIGURE 31-11: VOH vs. IOH OVER TEMPERATURE (VDD = 5.0V)
FIGURE 31-12 : VOL vs. IOL OVER TEMPERATURE (VDD = 5.0V)
FIGURE 31-13 : VOH vs. IOH OVER TEMPERATURE (VDD = 3.0V)
0
1
2
3
4
5
6
0 -2.5 -5 -7.5 -10 -12.5 -15 -17.5 -20 -22.5 -25 -27.5 -30
Typ.: 25°C Max.: -40°CMin.: 125°C
IOH (mA)
Max.: Maximum + 3
Min.: Minimum -3
VOH (V)
0
1
2
3
4
5
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75
Max.: 125°C Typ.: 25°C Min.: -40°C
VOL (V)
IOL (mA)
Max.: Maximum + 3
Min.: Minimum -3
0
0.5
1
1.5
2
2.5
3
3.5
-15-12.5-10-7.5-5-2.50
Typ.: 25°C Max.: -40°C
Min.: 125°C
IOH (mA)
Max.: Maximum + 3
Min.: Minimum -3
VOH (V)
2008-2011 Microchip Technology Inc. DS41364E-page 417
PIC16(L)F1934/6/7
FIGURE 31-14 : VOL vs. IOL OVER TEMPERATURE (VDD = 3.0V)
FIGURE 31-15 : VOH vs. IOH OVER TEMPERATURE (VDD = 1.8V)
FIGURE 31-16 : VOL vs. IOL OVER TEMPERATURE (VDD = 1.8V)
0
0.5
1
1.5
2
2.5
3
0 5 10 15 20 25 30
Max.: 125°C Typ.: 25°C Min.: -40°C
VOL (V)
IOL (mA)
Max.: Maximum + 3
Min.: Minimum -3
Typ.: 25°C
Max.: -40°C
Min.: 125°C
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
-5-4.5-4-3.5-3-2.5-2-1.5-1-0.50
IOH (mA)
VOH (V)
Max.: Maximum + 3
Min.: Minimum -3
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
012345678910
Max.: 125°C Typ.: 25°C Min.: -40°C
VOL (V)
IOL (mA)
Max.: Maximum + 3
Min.: Minimum -3
PIC16(L)F1934/6/7
DS41364E-page 418 2008-2011 Microchip Technology Inc.
FIGURE 31-17: PIC16LF1937 HF INTOSC MODE, FOSC = 8 MHz
FIGURE 31-18: PIC16F1937 MF INTOSC MODE, FOSC = 500 kHz
FIGURE 31-19: PIC16LF1937 HF INTOSC MODE, FOSC = 16 MHz
Max.
Typical
1
1.2
1.4
1.6
1.8
2
2.2
2.4
1.8 2 2.5 3 3.3 3.6
Max.: 25°C + 3
Typical: 25°C
IDD (mA)
VDD (V)
Max.
Typical
100
150
200
250
300
350
400
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
IDD (µA)
Max.: 25°C + 3
Typical: 25°C
Max.
Typical
1.5
2
2.5
3
3.5
4
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (mA)
Max.: 25°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 419
PIC16(L)F1934/6/7
FIGURE 31-20: PIC16F1937 HF INTOSC MODE, FOSC = 16 MHz
FIGURE 31-21: PIC16F1937 HF INTOSC MODE, FOSC = 8 MHz
FIGURE 31-22: PIC16F1937 LF INTOSC MODE, FOSC = 32 kHz
Max.
Typical
1.25
1.75
2.25
2.75
3.25
3.75
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
IDD (mA)
Max.: 25°C + 3
Typical: 25°C
Max.
Typical
0.75
0.95
1.15
1.35
1.55
1.75
1.95
2.15
1.8 2 2.5 3 3.3 3.6 4.2 5.5
IDD (mA)
5
4.5
Max.: 25°C + 3
Typical: 25°C
VDD (V)
Typical
Max.
20
25
30
35
40
45
50
55
60
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IDD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 420 2008-2011 Microchip Technology Inc.
FIGURE 31-23: PIC16LF1937 LF INTOSC MODE, FOSC = 32 kHz
FIGURE 31-24: PIC16LF1937 MF INTOSC MODE, FOSC = 500 kHz
FIGURE 31-25: PIC16LF1937 LP OSCILLATOR MODE, FOSC = 32 kHz
Typical
Max.
2
4
6
8
10
12
14
16
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (µA)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
75
95
115
135
155
175
195
215
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (mA)
Max.: 25°C + 3
Typical: 25°C
Typical
Max.
0
2
4
6
8
10
12
14
16
18
1.8 2 2.5 3 3.3 3.6
Max.: 85°C + 3
Typical: 25°C
IDD (µA)
VDD (V)
2008-2011 Microchip Technology Inc. DS41364E-page 421
PIC16(L)F1934/6/7
FIGURE 31-26: PIC16F1937 LP OSCILLATOR MODE, FOSC = 32 kHz
FIGURE 31-27: PIC16LF1937 HS OSCILLATOR MODE, FOSC = 32 MHz
FIGURE 31-28: PIC16F1937 HS OSCILLATOR MODE, FOSC = 32 MHz
Typical
Max.
20
25
30
35
40
45
50
55
60
65
70
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IDD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
2
3
4
5
6
7
1.8 2 2.5 3 3.3 3.6
IDD (mA)
VDD (V)
Max.: 25°C + 3
Typical: 25°C
Max.
Typical
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IDD (mA)
VDD (V)
Max.: -40°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 422 2008-2011 Microchip Technology Inc.
FIGURE 31-29: PIC16LF1937 EXTRC MODE, FOSC = 4 MHz
FIGURE 31-30: PIC16LF1937 XT OSCILLATOR, FOSC = 1 MHz
FIGURE 31-31 : PI C16F 19 37 XT OS CILL ATOR, FOSC = 1 MHz
Max.
Typical
200
300
400
500
600
700
800
900
1000
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (µA)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
50
100
150
200
250
300
350
400
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (µA)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
100
150
200
250
300
350
400
450
500
550
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
Current (µA)
2008-2011 Microchip Technology Inc. DS41364E-page 423
PIC16(L)F1934/6/7
FIGURE 31-32: PIC16LF1937 XT OSCILLATOR, FOSC = 4 MHz
FIGURE 31-33 : PI C16F 19 37 XT OS CILL ATOR, FOSC = 4 MHz
FIGURE 31-34: PIC16LF1937 EC OSCILLATOR, HIGH-POWER MODE, FOSC = 32 MHz
Max.
Typical
200
300
400
500
600
700
800
900
1000
1100
1.8 2 2.5 3 3.3 3.6
VDD (V)
Max.: 125°C + 3
Typical: 25°C
IDDA)
Max.
Typical
300
400
500
600
700
800
900
1000
1100
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
Max.: 125°C + 3
Typical: 25°C
VDD (V)
Current (µA)
Typical
Max.
2
3
4
5
6
7
8
1.8 2 2.5 3 3.3 3.6
IDD (mA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 424 2008-2011 Microchip Technology Inc.
FIGURE 31-35 : PI C16F19 37 EC OS CILL ATO R, HIGH-POWER MOD E, FOSC = 32 MHz
FIGURE 31-36: PIC16LF1937 EC OSCILLATOR, MEDIUM-POWER MODE, FOSC = 4 MHz
FIGURE 31-37 : PI C16F 19 37 EC OSCIL LAT O R, MEDIUM-P OWE R MODE, FOSC = 4 MHz
Typical
Max.
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
Curr en t (m A)
Max.: -40°C + 3
Typical: 25°C
Max.
Typical
200
300
400
500
600
700
800
900
1000
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (µA)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
300
400
500
600
700
800
900
1000
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
IDD (µA)
Max.: 125°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 425
PIC16(L)F1934/6/7
FIGURE 31-38: PIC16LF1937 EC OSCILLATOR, LOW-POWER MODE, FOSC = 500 kHz
FIGURE 31-39 : PI C16F 19 37 EC OSCILL AT OR, LOW-POW ER MO DE, FOSC = 500 kHz
FIGURE 31-40 : PI C16F 19 37 EXT RC MODE, FOSC = 4 MHz
Max.
Typical
0
20
40
60
80
100
120
140
160
1.8 2 2.5 3 3.3 3.6
VDD (V)
IDD (µA)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
40
60
80
100
120
140
160
180
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
IDDA)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
300
400
500
600
700
800
900
1000
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
VDD (V)
IDD (µA)
Max.: 125°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 426 2008-2011 Microchip Technology Inc.
FIGURE 31-41: PIC16LF1937 LCD, LOW POWER
FIGURE 31-42: PIC16LF1937 LCD, MEDIUM POWER
Max.
Typical
0
1
2
3
4
5
6
1.7 1.8 2 2.5 3 3.3 3.6
VDD (V)
IPD (µA)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
0
2
4
6
8
10
12
14
16
18
1.8 2 2.5 3 3.3 3.6
VDD (V)
IPDA)
Max.: 85°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 427
PIC16(L)F1934/6/7
FIGURE 31-43: PIC16LF1937 LCD, HIGH POWER
FIGURE 31-44: PIC16LF1937 A/D CURRENT
FIGURE 31-45: PIC16F19 37 A/D CURRENT
Max.
Typical
0
20
40
60
80
100
120
1.7 1.8 2 2.5 3 3.3
VDD (V)
Max.: 85°C + 3
Typical: 25°C
IPD (µA)
Typical
Max.
0
20
40
60
80
100
120
140
1.8 2 2.5 3 3.6
IPDA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
Typical
Max.
0
10
20
30
40
50
60
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 428 2008-2011 Microchip Technology Inc.
FIGURE 31-46 : PI C16L F19 37 HF INTOSC
FIGURE 31-47 : PI C16F19 37 HF INTOSC
FIGURE 31-48: PIC16LF1937 COMPARATOR 1, HIGH POWER
Max.
Typical
0.01
0.1
1
10
100
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
0
10
20
30
40
50
60
70
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPDA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
20
25
30
35
40
45
50
55
60
1.822.533.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 429
PIC16(L)F1934/6/7
FIGURE 31-49: PIC16F1937 COMPARATOR 1, HIGH POWER
FIGURE 31-50: PIC16LF1937 COMPARATOR 1, LOW POWER
Max.
Typical
30
40
50
60
70
80
90
100
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
5
6
7
8
9
10
11
12
13
14
15
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 430 2008-2011 Microchip Technology Inc.
FIGURE 31-51 : PI C16F 19 37 COM PARATOR 1, LOW POWER
FIGURE 31-52: PIC16LF1937 CAP SENSE, HIGH POWER
Max.
Typical
20
25
30
35
40
45
50
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
0
10
20
30
40
50
60
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 431
PIC16(L)F1934/6/7
FIGURE 31-53 : PI C 16F19 37 CAP SE NSE , HIGH POW ER
FIGURE 31-54: PIC16LF1937 CAP SENSE, MEDIUM POWER
FIGURE 31-55 : PI C16F 19 37 CAP SE NSE, MEDIU M POWE R
Max.
Typical
0
20
40
60
80
100
120
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA )
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
0
2
4
6
8
10
12
14
16
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
10
20
30
40
50
60
70
80
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 432 2008-2011 Microchip Technology Inc.
FIGURE 31-56: PIC16LF1937 COMPARATOR 2, HIGH POWER
FIGURE 31-57: PIC16F1937 COMPARATOR 2, HIGH POWER
FIGURE 31-58: PIC16LF1937 COMPARATOR 2, LOW POWER
Max.
Typical
20
25
30
35
40
45
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
30
35
40
45
50
55
60
65
70
75
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
0
2
4
6
8
10
12
14
16
18
20
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 433
PIC16(L)F1934/6/7
FIGURE 31-59 : PI C16F 19 37 COM PARATOR 2, LOW POWER
FIGURE 31-60: PIC16LF1937 CAP SENSE, LOW POWER
FIGURE 31-61 : PI C16F 19 37 CAP SE NSE , LOW POWER
Max.
Typical
20
25
30
35
40
45
50
55
60
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
0
2
4
6
8
10
12
14
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
Max.
Typical
0
10
20
30
40
50
60
70
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 125°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 434 2008-2011 Microchip Technology Inc.
FIGURE 31-62: PIC16LF1937 TIMER 1 OSCILLATOR
FIGURE 31-63 : PI C16F19 37 TIMER 1 OSCILLATO R
FIGURE 31-64: PIC16LF1937 BOR CURRENT
Max.
Typical
0
1
2
3
4
5
6
7
8
9
10
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
0
10
20
30
40
50
60
70
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
0
5
10
15
20
25
33.6 4
IPD (µA )
VDD (V)
Max.: 85°C + 3
Typical: 25°C
2008-2011 Microchip Technology Inc. DS41364E-page 435
PIC16(L)F1934/6/7
FIGURE 31-65: PIC16F19 37 BOR CURRENT
FIGURE 31-66 : PI C16LF 19 37 FVR_AD C
Max.
Typical
0
20
40
60
80
100
120
140
3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
0
5
10
15
20
25
30
1.8 2 2.5 3 3.6
IPD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
PIC16(L)F1934/6/7
DS41364E-page 436 2008-2011 Microchip Technology Inc.
FIGURE 31-67 : PI C16F 19 37 FVR_A DC
FIGURE 31-68 : PI C16L F19 37 WDT
Max.
Typical
0
20
40
60
80
100
120
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
VDD (V)
Max.: 85°C + 3
Typical: 25°C
Max.
Typical
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
1.8 2 2.5 3 3.6
IPD (µA)
Max.: 85°C + 3
Typical: 25°C
VDD (V)
2008-2011 Microchip Technology Inc. DS41364E-page 437
PIC16(L)F1934/6/7
FIGURE 31-69 : PI C16F 19 37 WDT
FIGURE 31-70 : PI C16LF 19 37 FVR_DA C
FIGURE 31-71 : PI C16F 19 37 FVR_D AC
Max.
Typical
0
5
10
15
20
25
30
35
40
45
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
Max.: 85°C + 3
Typical: 25°C
VDD (V)
Max.
Typical
0
5
10
15
20
25
30
1.822.533.6
IPD (µA)
Max.: 85°C + 3
Typical: 25°C
VDD (V)
Max.
Typical
0
20
40
60
80
100
120
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
IPD (µA)
Max.: 85°C + 3
Typical: 25°C
VDD (V)
PIC16(L)F1934/6/7
DS41364E-page 438 2008-2011 Microchip Technology Inc.
FIGURE 31-72: PIC16LF1937 BASE IPD
FIGURE 31-73 : PI C16F 19 37 BASE IPD
Typical
Max.
0.1
1
10
100
1.8 2 2.5 3 3.6
Max.: 85°C + 3
Typical: 25°C
IPD (µA)
VDD (V)
Typical
Max.
0
5
10
15
20
25
30
35
40
45
1.8 2 2.5 3 3.3 3.6 4.2 4.5 5 5.5
Max.: 85°C + 3
Typical: 25°C
IPD (µA)
VDD (V)
2008-2011 Microchip Technology Inc. DS41364E-page 439
PIC16(L)F1934/6/7
32.0 DEVELOPMENT SUPPORT
The PIC® microcontrollers and dsPIC® digital signal
controllers are supported with a full range of software
and hardware development tools:
Integrated Development Environment
- MPLAB® IDE Software
Compilers/Assemblers/Linkers
- MPLAB C Compiler for Various Device
Families
- HI-TECH C for Various Device Families
- MPASMTM Assembler
-MPLINK
TM Object Linker/
MPLIBTM Object Librarian
- MPLAB Assembler/Linker/Librarian for
Various Device Families
Simulators
- MPLAB SIM Software Simulator
•Emulators
- MPLAB REAL ICE™ In-Circuit Emulator
In-Circuit Debuggers
- MPLAB ICD 3
- PICkit™ 3 Debug Express
Device Programmers
- PICkit™ 2 Programmer
- MPLAB PM3 Device Programmer
Low-Cost Demonstration/Development Boards,
Evaluation Kits, and Starter Kits
32.1 MPLAB Integrated Development
Environment Software
The MPLAB IDE software brings an ease of software
development previously unseen in the 8/16/32-bit
microcontroller market. The MPLAB IDE is a Windows®
operating system-based application that contains:
A single graphical interface to all debugging tools
- Simulator
- Programmer (sold separately)
- In-Circuit Emulator (sold separately)
- In-Circuit Debugger (sold separately)
A full-featured editor with color-coded context
A multiple project manager
Customizable data windows with direct edit of
contents
High-level source code debugging
Mouse over variable inspection
Drag and drop variables from source to watch
windows
Extensive on-line help
Integration of select third party tools, such as
IAR C Compilers
The MPLAB IDE allows you to:
Edit your source files (either C or assembly)
One-touch compile or assemble, and download to
emulator and simulator tools (automatically
updates all project information)
Debug using:
- Source files (C or assembly)
- Mixed C and assembly
- Machine code
MPLAB IDE supports multiple debugging tools in a
single development paradigm, from the cost-effective
simulators, through low-cost in-circuit debuggers, to
full-featured emulators. This eliminates the learning
curve when upgrading to tools with increased flexibility
and power.
PIC16(L)F1934/6/7
DS41364E-page 440 2008-2011 Microchip Technology Inc.
32.2 MPLAB C Compilers for Var ious
Device Families
The MPLAB C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC18,
PIC24 and PIC32 families of microcontrollers and the
dsPIC30 and dsPIC33 families of digital signal control-
lers. These compilers provide powerful integration
capabilities, superior code optimization and ease of
use.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
32.3 HI-TECH C for Various Device
Families
The HI-TECH C Compiler code development systems
are complete ANSI C compilers for Microchip’s PIC
family of microcontrollers and the dsPIC family of digital
signal controllers. These compilers provide powerful
integration capabilities, omniscient code generation
and ease of use.
For easy source level debugging, the compilers provide
symbol information that is optimized to the MPLAB IDE
debugger.
The compilers include a macro assembler, linker, pre-
processor, and one-step driver, and can run on multiple
platforms.
32.4 MPASM Assembler
The MPASM Assembler is a full-featured, universal
macro assembler for PIC10/12/16/18 MCUs.
The MPASM Assembler generates relocatable object
files for the MPLINK Object Linker, Intel® standard HEX
files, MAP files to detail memory usage and symbol
reference, absolute LST files that contain source lines
and generated machine code and COFF files for
debugging.
The MPASM Assembler features include:
Integration into MPLAB IDE projects
User-defined macros to streamline
assembly code
Conditional assembly for multi-purpose
source files
Directives that allow complete control over the
assembly process
32.5 MPLINK Object Linker/
MPLIB Object Librarian
The MPLINK Object Linker combines relocatable
objects created by the MPASM Assembler and the
MPLAB C18 C Compiler. It can link relocatable objects
from precompiled libraries, using directives from a
linker script.
The MPLIB Object Librarian manages the creation and
modification of library files of precompiled code. When
a routine from a library is called from a source file, only
the modules that contain that routine will be linked in
with the application. This allows large libraries to be
used efficiently in many different applications.
The object linker/library features include:
Efficient linking of single libraries instead of many
smaller files
Enhanced code maintainability by grouping
related modules together
Flexible creation of libraries with easy module
listing, replacement, deletion and extraction
32.6 MPLAB Assembler, Linker and
Librarian for Various Device
Families
MPLAB Assembler produces relocatable machine
code from symbolic assembly language for PIC24,
PIC32 and dsPIC devices. MPLAB C Compiler uses
the assembler to produce its object file. The assembler
generates relocatable object files that can then be
archived or linked with other relocatable object files and
archives to create an executable file. Notable features
of the assembler include:
Support for the entire device instruction set
Support for fixed-point and floating-point data
Command line interface
Rich directive set
Flexible macro language
MPLAB IDE compatibility
2008-2011 Microchip Technology Inc. DS41364E-page 441
PIC16(L)F1934/6/7
32.7 MPLAB SIM Sof tware Simulator
The MPLAB SIM Software Simulator allows code
development in a PC-hosted environment by simulat-
ing the PIC MCUs and dsPIC® DSCs on an instruction
level. On any given instruction, the data areas can be
examined or modified and stimuli can be applied from
a comprehensive stimulus controller. Registers can be
logged to files for further run-time analysis. The trace
buffer and logic analyzer display extend the power of
the simulator to record and track program execution,
actions on I/O, most peripherals and internal registers.
The MPLAB SIM Software Simulator fully supports
symbolic debugging using the MPLAB C Compilers,
and the MPASM and MPLAB Assemblers. The soft-
ware simulator offers the flexibility to develop and
debug code outside of the hardware laboratory envi-
ronment, making it an excellent, economical software
development tool.
32.8 MPLAB REAL ICE In-Circuit
Emulator System
MPLAB REAL ICE In-Circuit Emulator System is
Microchip’s next generation high-speed emulator for
Microchip Flash DSC and MCU devices. It debugs and
programs PIC® Flash MCUs and dsPIC® Flash DSCs
with the easy-to-use, powerful graphical user interface of
the MPLAB Integrated Development Environment (IDE),
included with each kit.
The emulator is connected to the design engineer’s PC
using a high-speed USB 2.0 interface and is connected
to the target with either a connector compatible with in-
circuit debugger systems (RJ11) or with the new high-
speed, noise tolerant, Low-Voltage Differential Signal
(LVDS) interconnection (CAT5).
The emulator is field upgradable through future firmware
downloads in MPLAB IDE. In upcoming releases of
MPLAB IDE, new devices will be supported, and new
features will be added. MPLAB REAL ICE offers
significant advantages over competitive emulators
including low-cost, full-speed emulation, run-time
variable watches, trace analysis, complex breakpoints, a
ruggedized probe interface and long (up to three meters)
interconnection cables.
32.9 MPLAB ICD 3 In-Circuit Debugger
System
MPLAB ICD 3 In-Circuit Debugger System is Micro-
chip’s most cost effective high-speed hardware
debugger/programmer for Microchip Flash Digital Sig-
nal Controller (DSC) and microcontroller (MCU)
devices. It debugs and programs PIC® Flash microcon-
trollers and dsPIC® DSCs with the powerful, yet easy-
to-use graphical user interface of MPLAB Integrated
Development Environment (IDE).
The MPLAB ICD 3 In-Circuit Debugger probe is con-
nected to the design engineer’s PC using a high-speed
USB 2.0 interface and is connected to the target with a
connector compatible with the MPLAB ICD 2 or MPLAB
REAL ICE systems (RJ-11). MPLAB ICD 3 supports all
MPLAB ICD 2 headers.
32.10 PICkit 3 In-Circuit Debugger/
Programmer and
PICkit 3 Debug Express
The MPLAB PICkit 3 allows debugging and program-
ming of PIC® and dsPIC® Flash microcontrollers at a
most affordable price point using the powerful graphical
user interface of the MPLAB Integrated Development
Environment (IDE). The MPLAB PICkit 3 is connected
to the design engineer’s PC using a full speed USB
interface and can be connected to the target via an
Microchip debug (RJ-11) connector (compatible with
MPLAB ICD 3 and MPLAB REAL ICE). The connector
uses two device I/O pins and the reset line to imple-
ment in-circuit debugging and In-Circuit Serial Pro-
gramming™.
The PICkit 3 Debug Express include the PICkit 3, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
PIC16(L)F1934/6/7
DS41364E-page 442 2008-2011 Microchip Technology Inc.
32.11 PICkit 2 Development
Programmer/Debugger and
PICkit 2 Debug Express
The PICkit™ 2 Development Programmer/Debugger is
a low-cost development tool with an easy to use inter-
face for programming and debugging Microchip’s Flash
families of microcontrollers. The full featured
Windows® programming interface supports baseline
(PIC10F, PIC12F5xx, PIC16F5xx), midrange
(PIC12F6xx, PIC16F), PIC18F, PIC24, dsPIC30,
dsPIC33, and PIC32 families of 8-bit, 16-bit, and 32-bit
microcontrollers, and many Microchip Serial EEPROM
products. With Microchip’s powerful MPLAB Integrated
Development Environment (IDE) the PICkit™ 2
enables in-circuit debugging on most PIC® microcon-
trollers. In-Circuit-Debugging runs, halts and single
steps the program while the PIC microcontroller is
embedded in the application. When halted at a break-
point, the file registers can be examined and modified.
The PICkit 2 Debug Express include the PICkit 2, demo
board and microcontroller, hookup cables and CDROM
with user’s guide, lessons, tutorial, compiler and
MPLAB IDE software.
32.12 MPLAB PM3 Device Programmer
The MPLAB PM3 Device Programmer is a universal,
CE compliant device programmer with programmable
voltage verification at VDDMIN and VDDMAX for
maximum reliability. It features a large LCD display
(128 x 64) for menus and error messages and a modu-
lar, detachable socket assembly to support various
package types. The ICSP™ cable assembly is included
as a standard item. In Stand-Alone mode, the MPLAB
PM3 Device Programmer can read, verify and program
PIC devices without a PC connection. It can also set
code protection in this mode. The MPLAB PM3
connects to the host PC via an RS-232 or USB cable.
The MPLAB PM3 has high-speed communications and
optimized algorithms for quick programming of large
memory devices and incorporates an MMC card for file
storage and data applications.
32.13 Demonstration/Development
Boards, Evaluation Kits, and
Starter Kits
A wide variety of demonstration, development and
evaluation boards for various PIC MCUs and dsPIC
DSCs allows quick application development on fully func-
tional systems. Most boards include prototyping areas for
adding custom circuitry and provide application firmware
and source code for examination and modification.
The boards support a variety of features, including LEDs,
temperature sensors, switches, speakers, RS-232
interfaces, LCD displays, potentiometers and additional
EEPROM memory.
The demonstration and development boards can be
used in teaching environments, for prototyping custom
circuits and for learning about various microcontroller
applications.
In addition to the PICDEM™ and dsPICDEM™ demon-
stration/development board series of circuits, Microchip
has a line of evaluation kits and demonstration software
for analog filter design, KEELOQ® security ICs, CAN,
IrDA®, PowerSmart battery management, SEEVAL®
evaluation system, Sigma-Delta ADC, flow rate
sensing, plus many more.
Also available are starter kits that contain everything
needed to experience the specified device. This usually
includes a single application and debug capability, all
on one board.
Check the Microchip web page (www.microchip.com)
for the complete list of demonstration, development
and evaluation kits.
2008-2011 Microchip Technology Inc. DS41364E-page 443
PIC16(L)F1934/6/7
33.0 PACKAGING INFORMATION
33.1 Package Marking Information
40-Lead PDIP (600 mil) Example
XXXXXXXXXXXXXXXXXX
YYWWNNN
XXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXX
3
e
PIC16F1937
1048017
-I/P
*Standard PICmicro® device marking consists of Microchip part number, year code, week code and
traceability code. For PICmicro device marking beyond this, certain price adders apply. Please check
with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP
price.
Legend: XX...X Customer-specific information
Y Year code (last digit of calendar year)
YY Year code (last 2 digits of calendar year)
WW Week code (week of January 1 is week ‘01’)
NNN Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
*This package is Pb-free. The Pb-free JEDEC designator ( )
can be found on the outer packaging for this package.
Note: In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
3
e
3
e
28-Lead SOIC (7.50 mm) Example
YYWWNNN
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXXXXXX
0810017
-I/SO
3
e
PIC16F1936
28-Lead SPDIP (300 mil) Example
XXXXXXXXXXXXXXX
YYWWNNN
XXXXXXXXXXXXXXX
XXXXXXXXXXXXXXX
3
e
PIC16F1936
1048017
-I/SP
PIC16(L)F1934/6/7
DS41364E-page 444 2008-2011 Microchip Technology Inc.
Package Marking Information (Continued)
28-Lead SSOP (5.30 mm) Example
PIC16F1936
0810017
-I/SS
3
e
28-Lead UQFN (4x4x0.5 mm) Example
PIN 1 PIN 1
PIC16
048017
F1936
I/ML
3
e
40-Lead UQFN (5x5x0.5 mm) Example
PIN 1 PIN 1
3
e
PIC16F1937
-I/ML
0810017
2008-2011 Microchip Technology Inc. DS41364E-page 445
PIC16(L)F1934/6/7
Package Marking Information (Continued)
44-Lead TQFP (10x10x1 mm) Example
XXXXXXXXXX
YYWWNNN
XXXXXXXXXX
XXXXXXXXXX
PIC16F1937
0810017
-I/PT
3
e
44-Lead QFN (8x8x0.9 mm) Example
XXXXXXXXXXX
XXXXXXXXXXX
YYWWNNN
XXXXXXXXXXX
PIN 1 PIN 1
3
e
PIC16F1937
-I/ML
0810017
PIC16(L)F1934/6/7
DS41364E-page 446 2008-2011 Microchip Technology Inc.
33.2 Package Details
The following sections give the technical details of the packages.

!"
 
 
 
 
 
!" 

 
   
 
 
 
    
 
   
    
   
   
   
    
   
  
NOTE 1
N
12
D
E1
eB
c
E
L
A2
eb
b1
A1
A
3
   
2008-2011 Microchip Technology Inc. DS41364E-page 447
PIC16(L)F1934/6/7
#$
!"
 
 
 
 
 
!" 

 
   
 
 
 
   
 
  
   
  
  
  
   
  
  
N
NOTE 1
E1
D
123
A
A1 b1
be
c
eB
E
L
A2
   
PIC16(L)F1934/6/7
DS41364E-page 448 2008-2011 Microchip Technology Inc.
%%&'()*%+
!"
 
 
 
 
 
 
!" 

 
   
 
 
 
 
   
 
  
 
  
  
  
  
  
  
  
  
c
h
h
L
L1
A2
A1
A
NOTE 1
123
b
e
E
E1
D
φ
β
α
N
   
2008-2011 Microchip Technology Inc. DS41364E-page 449
PIC16(L)F1934/6/7
,-%*)%
!"
 
 
 
 
 
!" 

 
   
 
 
 
   
  
   
    
   
   
  
  
   
  
L
L1
c
A2
A1
A
E
E1
D
N
12
NOTE 1 b
e
φ
   
PIC16(L)F1934/6/7
DS41364E-page 450 2008-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2011 Microchip Technology Inc. DS41364E-page 451
PIC16(L)F1934/6/7
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
PIC16(L)F1934/6/7
DS41364E-page 452 2008-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2011 Microchip Technology Inc. DS41364E-page 453
PIC16(L)F1934/6/7
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
PIC16(L)F1934/6/7
DS41364E-page 454 2008-2011 Microchip Technology Inc.
Note: For the most current package drawings, please see the Microchip Packaging Specification located at
http://www.microchip.com/packaging
2008-2011 Microchip Technology Inc. DS41364E-page 455
PIC16(L)F1934/6/7
##.,/01.23232')./0
!"
 
 
 
 
 
 
!" 

 
   
 
 
 
   
   
   
  
   
 
 
  
  
  
   
   
   
A
E
E1
D
D1
e
b
NOTE 1 NOTE 2
N
123
c
A1
L
A2
L1
α
φ
β
   
PIC16(L)F1934/6/7
DS41364E-page 456 2008-2011 Microchip Technology Inc.
##.,/01.23232')./0
!" 

2008-2011 Microchip Technology Inc. DS41364E-page 457
PIC16(L)F1934/6/7
##/0'!453/0!
!"
 
 
 
 
 
!" 

 
   
 
 
   
    
  
 
    
 
    
   
   
 
DEXPOSED
PAD
D2
e
b
K
L
E2
2
1
N
NOTE 1
2
1
E
N
BOTTOM VIEW
TOP VIEW
A3 A1
A
   
PIC16(L)F1934/6/7
DS41364E-page 458 2008-2011 Microchip Technology Inc.
##/0'!453/0!
!" 

2008-2011 Microchip Technology Inc. DS41364E-page 459
PIC16(L)F1934/6/7
APPENDIX A: DATA SHEE T
REVISION HISTORY
Revision A (12/2008)
Original release
Revision B (04/2009)
Revised data sheet title; Revised Features section.
Revision C (10/2009)
Added PIC16L/LF1933/34. General updates.
Revision D (12/2009)
General updates.
Revision E (5/2011)
Separated 193X data sheet into three separate data
sheets. Added Characterization Data.
APPENDIX B: MIGRATING FROM
OTHER PIC®
DEVICES
This discusses some of the issues in migrating from
other PIC® devices to the PIC16(L)F1934/6/7 family of
devices.
B.1 PIC16F917 to PIC16F1937
TABLE B-1: FEATURE COMPARISON
Feature PIC16F917 PIC16F1937
Max. Operating Speed 20 MHz 32 MHz
Max. Program
Memory (Words)
8K 8K
Max. SRAM (Bytes) 368 512
A/D Resolution 10-bit 10-bit
Timers (8/16-bit) 2/1 4/1
Oscillator Modes 4 8
Brown-out Reset Y Y
Internal Pull-ups RB<7:0> RB<7:0>
Interrupt-on-change RB<7:4> RB<7:0>
Comparator 2 2
AUSART/EUSART 1/0 0/1
Extended WDT Y Y
Software Control
Option of WDT/BOR
NY
INTOSC Frequencies 30 kHz -
8MHz
500 kHz -
32 MHz
Clock Switching Y Y
Capacitive Sensing N Y
CCP/ECCP 2/0 2/3
Enhanced PIC16 CPU N Y
MSSP/SSP 0/1 1/0
LCD Y Y
PIC16(L)F1934/6/7
DS41364E-page 460 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 461
PIC16(L)F1934/6/7
INDEX
A
A/D
Specifications............................................................ 403
Absolute Maximum Ratings (PIC16F/LF1934/36/37) ....... 381
AC Characteristics
Industrial and Extended ............................................ 396
Load Conditions ........................................................ 395
ACKSTAT ......................................................................... 276
ACKSTAT Status Flag ...................................................... 276
ADC .................................................................................. 159
Acquisition Requirements ......................................... 169
Associated registers.................................................. 171
Block Diagram........................................................... 159
Calculating Acquisition Time..................................... 169
Channel Selection..................................................... 160
Configuration............................................................. 160
Configuring Interrupt ................................................. 164
Conversion Clock...................................................... 160
Conversion Procedure .............................................. 164
Internal Sampling Switch (RSS) Impedance.............. 169
Interrupts................................................................... 162
Operation .................................................................. 163
Operation During Sleep ............................................ 163
Port Configuration..................................................... 160
Reference Voltage (VREF)......................................... 160
Source Impedance.................................................... 169
Special Event Trigger................................................ 163
Starting an A/D Conversion ......................................162
ADCON0 Register....................................................... 40, 165
ADCON1 Register....................................................... 40, 166
ADDFSR ........................................................................... 371
ADDWFC .......................................................................... 371
ADRESH Register............................................................... 40
ADRESH Register (ADFM = 0) ......................................... 167
ADRESH Register (ADFM = 1) ......................................... 168
ADRESL Register (ADFM = 0).......................................... 167
ADRESL Register (ADFM = 1).......................................... 168
Alternate Pin Function....................................................... 132
Analog-to-Digital Converter. See ADC
ANSELA Register ............................................................. 136
ANSELB Register ............................................................. 141
ANSELD Register ............................................................. 148
ANSELE Register ............................................................. 151
APFCON Register............................................................. 133
Assembler
MPASM Assembler................................................... 442
B
BAUDCON Register.......................................................... 304
BF ............................................................................. 276, 278
BF Status Flag .......................................................... 276, 278
Block Diagram
Capacitive Sensing ................................................... 321
Block Diagrams
(CCP) Capture Mode Operation ............................... 214
ADC .......................................................................... 159
ADC Transfer Function ............................................. 170
Analog Input Model ........................................... 170, 184
CCP PWM................................................................. 218
Clock Source............................................................... 70
Comparator ............................................................... 180
Compare ................................................................... 216
Crystal Operation.................................................. 72, 73
Digital-to-Analog Converter (DAC) ........................... 176
EUSART Receive ..................................................... 294
EUSART Transmit .................................................... 293
External RC Mode ...................................................... 73
Fail-Safe Clock Monitor (FSCM)................................. 81
Generic I/O Port........................................................ 131
Interrupt Logic............................................................. 95
LCD Bias Voltage Generation .................................. 337
LCD Clock Generation.............................................. 336
On-Chip Reset Circuit................................................. 87
PIC16F193X/LF193X ........................................... 16, 24
PWM (Enhanced) ..................................................... 222
Resonator Operation .................................................. 72
Timer0 ...................................................................... 193
Timer1 ...................................................................... 197
Timer1 Gate.............................................. 202, 203, 204
Timer2/4/6 ................................................................ 209
Voltage Reference.................................................... 157
Voltage Reference Output Buffer Example .............. 176
BORCON Register.............................................................. 89
BRA .................................................................................. 372
Break Character (12-bit) Transmit and Receive ............... 313
Brown-out Reset (BOR)...................................................... 89
Specifications ........................................................... 401
Timing and Characteristics ....................................... 400
C
C Compilers
MPLAB C18.............................................................. 442
CALL................................................................................. 373
CALLW ............................................................................. 373
Capacitive Sensing ........................................................... 321
Associated registers w/ Capacitive Sensing............. 327
Specifications ........................................................... 412
Capture Module. See Enhanced Capture/Compare/
PWM(ECCP)
Capture/Compare/PWM ................................................... 213
Capture/Compare/PWM (CCP)
Associated Registers w/ Capture ............................. 215
Associated Registers w/ Compare ........................... 217
Associated Registers w/ PWM ......................... 221, 235
Capture Mode........................................................... 214
CCPx Pin Configuration............................................ 214
Compare Mode......................................................... 216
CCPx Pin Configuration.................................... 216
Software Interrupt Mode........................... 214, 216
Special Event Trigger ....................................... 216
Timer1 Mode Resource ............................ 214, 216
Prescaler .................................................................. 214
PWM Mode
Duty Cycle ........................................................ 219
Effects of Reset ................................................ 221
Example PWM Frequencies and
Resolutions, 20 MHZ................................ 220
Example PWM Frequencies and
Resolutions, 32 MHZ................................ 220
Example PWM Frequencies and
Resolutions, 8 MHz .................................. 220
Operation in Sleep Mode.................................. 221
Resolution ........................................................ 220
System Clock Frequency Changes .................. 221
PWM Operation ........................................................ 218
PWM Overview......................................................... 218
PWM Period ............................................................. 219
PIC16(L)F1934/6/7
DS41364E-page 462 2008-2011 Microchip Technology Inc.
PWM Setup...............................................................219
CCP1CON Register ...................................................... 44, 45
CCPR1H Register ......................................................... 44, 45
CCPR1L Register.......................................................... 44, 45
CCPTMRS0 Register ........................................................237
CCPTMRS1 Register ........................................................237
CCPxAS Register..............................................................238
CCPxCON (ECCPx) Register ........................................... 236
Clock Accuracy with Asynchronous Operation ................. 302
Clock Sources
External Modes ........................................................... 71
EC ....................................................................... 71
HS ....................................................................... 71
LP........................................................................71
OST..................................................................... 72
RC....................................................................... 73
XT ....................................................................... 71
Internal Modes ............................................................ 74
HFINTOSC.......................................................... 74
Internal Oscillator Clock Switch Timing...............76
LFINTOSC .......................................................... 75
MFINTOSC ......................................................... 74
Clock Switching...................................................................78
CMOUT Register...............................................................186
CMxCON0 Register ..........................................................185
CMxCON1 Register ..........................................................186
Code Examples
A/D Conversion.........................................................164
Changing Between Capture Prescalers .................... 214
Initializing PORTA..................................................... 131
Initializing PORTE..................................................... 150
Write Verify ...............................................................127
Writing to Flash Program Memory ............................ 125
Comparator
Associated Registers ........................................ 187, 188
Operation .................................................................. 179
Comparator Module .......................................................... 179
Cx Output State Versus Input Conditions ................. 181
Comparator Specifications ................................................ 405
Comparators
C2OUT as T1 Gate ...................................................199
Compare Module. See Enhanced Capture/Compare/
PWM (ECCP)
CONFIG1 Register.............................................................. 62
CONFIG2 Register.............................................................. 64
Core Registers ....................................................................39
CPSCON0 Register .......................................................... 325
CPSCON1 Register .......................................................... 326
Customer Change Notification Service ............................. 471
Customer Notification Service........................................... 471
Customer Support ............................................................. 471
D
DACCON0 (Digital-to-Analog Converter Control 0)
Register..................................................................... 178
DACCON1 (Digital-to-Analog Converter Control 1)
Register..................................................................... 178
Memory ............................................................................ 117
Associated Registers ................................................ 130
Code Protection ........................................................ 118
Reading..................................................................... 118
Writing....................................................................... 118
Data Memory................................................................. 28, 31
DC and AC Characteristics ............................................... 413
DC Characteristics
Extended and Industrial (PIC16F/LF1934/36/37) ..... 391
Industrial and Extended (PIC16F/LF1934/36/37) ..... 384
Development Support....................................................... 441
Device Configuration .......................................................... 61
Code Protection.......................................................... 65
Configuration Word..................................................... 61
User ID ................................................................. 65, 66
Device Overview......................................................... 15, 113
Digital-to-Analog Converter (DAC) ................................... 175
Associated Registers ................................................ 178
Effects of a Reset ..................................................... 176
Specifications ........................................................... 405
E
ECCP/CCP. See Enhanced Capture/Compare/PWM
EEADR Registers ............................................................. 117
EEADRH Registers........................................................... 117
EEADRL Register ............................................................. 128
EEADRL Registers ........................................................... 117
EECON1 Register..................................................... 117, 129
EECON2 Register..................................................... 117, 130
EEDATH Register............................................................. 128
EEDATL Register ............................................................. 128
EEPROM Data Memory
Avoiding Spurious Write ........................................... 118
Write Verify ............................................................... 127
Effects of Reset
PWM mode............................................................... 221
Electrical Specifications (PIC16F/LF1934/36/37) ............. 381
Enhanced Capture/Compare/PWM (ECCP)..................... 213
Enhanced PWM Mode.............................................. 222
Auto-Restart ..................................................... 231
Auto-shutdown.................................................. 230
Direction Change in Full-Bridge Output Mode.. 228
Full-Bridge Application...................................... 226
Full-Bridge Mode .............................................. 226
Half-Bridge Application ..................................... 225
Half-Bridge Application Examples .................... 232
Half-Bridge Mode.............................................. 225
Output Relationships (Active-High and
Active-Low)............................................... 223
Output Relationships Diagram.......................... 224
Programmable Dead Band Delay..................... 232
Shoot-through Current...................................... 232
Start-up Considerations .................................... 234
Specifications ........................................................... 402
Enhanced Mid-range CPU.................................................. 23
Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) .............................. 293
Errata .................................................................................. 14
EUSART ........................................................................... 293
Associated Registers
Baud Rate Generator ....................................... 306
Asynchronous Mode ................................................. 295
12-bit Break Transmit and Receive .................. 313
Associated Registers
Receive .................................................... 301
Transmit.................................................... 297
Auto-Wake-up on Break ................................... 311
Baud Rate Generator (BRG) ............................ 305
Clock Accuracy................................................. 302
Receiver ........................................................... 298
Setting up 9-bit Mode with Address Detect ...... 300
Transmitter ....................................................... 295
Baud Rate Generator (BRG)
Auto Baud Rate Detect..................................... 310
Baud Rate Error, Calculating............................ 305
2008-2011 Microchip Technology Inc. DS41364E-page 463
PIC16(L)F1934/6/7
Baud Rates, Asynchronous Modes .................. 307
Formulas ........................................................... 306
High Baud Rate Select (BRGH Bit) .................. 305
Synchronous Master Mode ............................... 314, 318
Associated Registers
Receive..................................................... 317
Transmit.................................................... 315
Reception.......................................................... 316
Transmission .................................................... 314
Synchronous Slave Mode
Associated Registers
Receive..................................................... 319
Transmit.................................................... 318
Reception.......................................................... 319
Transmission .................................................... 318
Extended Instruction Set
ADDFSR ................................................................... 371
F
Fail-Safe Clock Monitor....................................................... 81
Fail-Safe Condition Clearing....................................... 81
Fail-Safe Detection ..................................................... 81
Fail-Safe Operation..................................................... 81
Reset or Wake-up from Sleep..................................... 81
Firmware Instructions........................................................ 367
Fixed Voltage Reference (FVR)
Associated Registers ................................................ 158
Flash Program Memory .................................................... 117
Erasing...................................................................... 122
Modifying................................................................... 126
Writing....................................................................... 122
FSR Register39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 51, 52
FVRCON (Fixed Voltage Reference Control) Register..... 158
I
I2C Mode (MSSP)
Acknowledge Sequence Timing................................ 280
Bus Collision
During a Repeated Start Condition................... 284
During a Stop Condition.................................... 285
Effects of a Reset...................................................... 281
I2C Clock Rate w/BRG.............................................. 287
Master Mode
Operation .......................................................... 272
Reception.......................................................... 278
Start Condition Timing .............................. 274, 275
Transmission .................................................... 276
Multi-Master Communication, Bus Collision and
Arbitration ......................................................... 281
Multi-Master Mode .................................................... 281
Read/Write Bit Information (R/W Bit) ........................ 257
Slave Mode
Transmission .................................................... 262
Sleep Operation ........................................................ 281
Stop Condition Timing............................................... 280
INDF Register39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 51, 52
Indirect Addressing ............................................................. 56
Instruction Format ............................................................. 368
Instruction Set ................................................................... 367
ADDLW ..................................................................... 371
ADDWF..................................................................... 371
ADDWFC .................................................................. 371
ANDLW ..................................................................... 371
ANDWF..................................................................... 371
BRA........................................................................... 372
CALL ......................................................................... 373
CALLW ..................................................................... 373
LSLF ......................................................................... 375
LSRF ........................................................................ 375
MOVF ....................................................................... 375
MOVIW ..................................................................... 376
MOVLB ..................................................................... 376
MOVWI..................................................................... 377
OPTION.................................................................... 377
RESET...................................................................... 377
SUBWFB .................................................................. 379
TRIS ......................................................................... 380
BCF .......................................................................... 372
BSF........................................................................... 372
BTFSC...................................................................... 372
BTFSS ...................................................................... 372
CALL......................................................................... 373
CLRF ........................................................................ 373
CLRW ....................................................................... 373
CLRWDT .................................................................. 373
COMF ....................................................................... 373
DECF........................................................................ 373
DECFSZ ................................................................... 374
GOTO ....................................................................... 374
INCF ......................................................................... 374
INCFSZ..................................................................... 374
IORLW...................................................................... 374
IORWF...................................................................... 374
MOVLW .................................................................... 376
MOVWF.................................................................... 376
NOP.......................................................................... 377
RETFIE..................................................................... 378
RETLW ..................................................................... 378
RETURN................................................................... 378
RLF........................................................................... 378
RRF .......................................................................... 379
SLEEP ...................................................................... 379
SUBLW..................................................................... 379
SUBWF..................................................................... 379
SWAPF..................................................................... 380
XORLW .................................................................... 380
XORWF .................................................................... 380
INTCON Register.............................................................. 100
Internal Oscillator Block
INTOSC
Specifications ................................................... 397
Internal Sampling Switch (RSS) Impedance ..................... 169
Internet Address ............................................................... 471
Interrupt-On-Change......................................................... 153
Associated Registers................................................ 155
Interrupts ............................................................................ 95
ADC .......................................................................... 164
Associated registers w/ Interrupts ............................ 107
Configuration Word w/ Clock Sources........................ 85
Configuration Word w/ LDO...................................... 109
TMR1........................................................................ 201
INTOSC Specifications ..................................................... 397
IOCBF Register ................................................................ 154
IOCBN Register................................................................ 154
IOCBP Register ................................................................ 154
L
LATA Register .......................................................... 135, 144
LATB Register .................................................................. 140
LATD Register .................................................................. 147
LATE Register .................................................................. 151
LCD
PIC16(L)F1934/6/7
DS41364E-page 464 2008-2011 Microchip Technology Inc.
Associated Registers ................................................ 362
Bias Voltage Generation ................................... 337, 338
Clock Source Selection............................................. 336
Configuring the Module............................................. 361
Disabling the Module ................................................ 361
Frame Frequency......................................................344
Interrupts................................................................... 357
LCDCON Register ....................................................330
LCDPS Register........................................................ 330
Multiplex Types .........................................................344
Operation During Sleep ............................................ 359
Pixel Control.............................................................. 344
Prescaler................................................................... 336
Segment Enables......................................................344
Waveform Generation............................................... 346
LCDCON Register..................................................... 330, 331
LCDCST Register ............................................................. 334
LCDDATAx Registers ............................................... 335, 342
LCDPS Register........................................................ 330, 332
LP Bits....................................................................... 336
LCDREF Register ............................................................. 333
LCDRL Register................................................................342
LCDSEn Registers............................................................335
Liquid Crystal Display (LCD) Driver .................................. 329
Load Conditions ................................................................ 395
LSLF.................................................................................. 375
LSRF ................................................................................. 375
M
Master Synchronous Serial Port. See MSSP
MCLR .................................................................................. 90
Internal ........................................................................90
Memory Organization
Data ...................................................................... 28, 31
Program ...................................................................... 25
Microchip Internet Web Site..............................................471
Migrating from other PIC Microcontroller Devices............. 461
MOVIW.............................................................................. 376
MOVLB.............................................................................. 376
MOVWI.............................................................................. 377
MPLAB ASM30 Assembler, Linker, Librarian ................... 442
MPLAB Integrated Development Environment Software .. 441
MPLAB PM3 Device Programmer..................................... 444
MPLAB REAL ICE In-Circuit Emulator System.................443
MPLINK Object Linker/MPLIB Object Librarian ................ 442
MSSP ................................................................................ 241
SPI Mode ..................................................................244
SSPBUF Register ..................................................... 247
SSPSR Register ....................................................... 247
O
OPCODE Field Descriptions............................................. 367
OPTION ............................................................................ 377
OPTION Register.............................................................. 195
OSCCON Register ..............................................................83
Oscillator
Associated Registers .................................................. 85
Oscillator Module ................................................................69
ECH ............................................................................ 69
ECL ............................................................................. 69
ECM ............................................................................ 69
HS ............................................................................... 69
INTOSC ......................................................................69
LP................................................................................ 69
RC............................................................................... 69
XT ............................................................................... 69
Oscillator Parameters ....................................................... 397
Oscillator Specifications.................................................... 396
Oscillator Start-up Timer (OST)
Specifications ........................................................... 401
Oscillator Switching
Fail-Safe Clock Monitor .............................................. 81
Two-Speed Clock Start-up.......................................... 79
OSCSTAT Register ............................................................ 84
OSCTUNE Register............................................................ 85
P
P1A/P1B/P1C/P1D.See Enhanced Capture/Compare/
PWM (ECCP)............................................................ 222
Packaging ......................................................................... 445
Marking..................................................... 445, 446, 447
PDIP Details ............................................................. 448
PCL and PCLATH............................................................... 24
PCL Register39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 51, 52
PCLATH Register39, 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 51,
.................................................................................... 52
PCON Register ............................................................. 40, 93
PIE1 Register.............................................................. 40, 101
PIE2 Register.............................................................. 40, 102
PIE3 Register.................................................................... 103
Pin Diagram
PIC16(L)F1934/1937, 40-pin PDIP............................... 8
PIC16(L)F1934/1937, 40-pin UQFN ............................. 9
PIC16(L)F1934/1937, 44-pin QFN.............................. 10
PIC16(L)F1934/1937, 44-pin TQFP............................ 11
PIC16(L)F1936, 28-pin QFN/UQFN ............................. 6
PIC16(L)F1936, 28-pin SPDIP/SOIC/SSOP................. 5
Pinout Descriptions
PIC16F193X/PIC16LF193X........................................ 17
PIR1 Register ............................................................. 39, 104
PIR2 Register ............................................................. 39, 105
PIR3 Register ................................................................... 106
PORTA ............................................................................. 134
ANSELA Register ..................................................... 134
Associated Registers ................................................ 137
Configuration Word w/ PORTA................................. 137
PORTA Register................................................... 39, 41
Specifications ........................................................... 399
PORTA Register ............................................................... 135
PORTB ............................................................................. 138
Additional Pin Functions
Weak Pull-up .................................................... 139
ANSELB Register ..................................................... 138
Associated Registers ................................................ 142
Interrupt-on-Change ................................................. 138
P1B/P1C/P1D.See Enhanced Capture/Compare/
PWM+ (ECCP+) ............................................... 138
Pin Descriptions and Diagrams ................................ 139
PORTB Register................................................... 39, 41
PORTB Register ............................................................... 140
PORTC ............................................................................. 143
Associated Registers ................................................ 145
P1A.See Enhanced Capture/Compare/PWM+
(ECCP+) ........................................................... 143
Pin Descriptions and Diagrams ................................ 143
PORTC Register................................................... 39, 41
Specifications ........................................................... 399
PORTC Register............................................................... 144
PORTD ............................................................................. 146
Additional Pin Functions
ANSELD Register............................................. 146
Associated Registers ................................................ 148
2008-2011 Microchip Technology Inc. DS41364E-page 465
PIC16(L)F1934/6/7
P1B/P1C/P1D.See Enhanced Capture/Compare/
PWM+ (ECCP+) ............................................... 146
Pin Descriptions and Diagrams................................. 146
PORTD Register ...................................................39, 41
PORTD Register ............................................................... 147
PORTE.............................................................................. 149
ANSELE Register ..................................................... 149
Associated Registers ................................................ 152
Pin Descriptions and Diagrams................................. 149
PORTE Register ................................................... 39, 41
PORTE Register ............................................................... 150
Power-Down Mode (Sleep) ............................................... 111
Associated Registers ................................................ 112
Power-on Reset .................................................................. 88
Power-up Timer (PWRT) .................................................... 88
Specifications............................................................ 401
PR2 Register................................................................. 39, 47
Precision Internal Oscillator Parameters........................... 397
Program Memory ................................................................ 25
Map and Stack (PIC16(L)F1934) ................................ 25
Map and Stack (PIC16(L)F1936, PIC16(L)F1937) ..... 26
Map and Stack (PIC16F1934/LF1934) ....................... 31
Map and Stack (PIC16F1936/LF1936,
PIC16F1937/LF1937) ......................................... 31
Programming Mode Exit ..................................................... 90
Programming, Device Instructions .................................... 367
PSTRxCON Register ........................................................ 240
PWM (ECCP Module)
PWM Steering........................................................... 233
Steering Synchronization.......................................... 234
PWM Mode. See Enhanced Capture/Compare/PWM ...... 222
PWM Steering................................................................... 233
PWMxCON Register ......................................................... 239
R
RCREG ............................................................................. 300
RCREG Register................................................................. 42
RCSTA Register ......................................................... 42, 303
Reader Response ............................................................. 472
Read-Modify-Write Operations ......................................... 367
Register
RCREG Register....................................................... 310
Registers
ADCON0 (ADC Control 0) ........................................ 165
ADCON1 (ADC Control 1) ........................................ 166
ADRESH (ADC Result High) with ADFM = 0)........... 167
ADRESH (ADC Result High) with ADFM = 1)........... 168
ADRESL (ADC Result Low) with ADFM = 0) ............ 167
ADRESL (ADC Result Low) with ADFM = 1) ............ 168
ANSELA (PORTA Analog Select)............................. 136
ANSELB (PORTB Analog Select)............................. 141
ANSELD (PORTD Analog Select) ............................ 148
ANSELE (PORTE Analog Select)............................. 151
APFCON (Alternate Pin Function Control)................ 133
BAUDCON (Baud Rate Control) ............................... 304
BORCON Brown-out Reset Control)........................... 89
CCPTMRS0 (PWM Timer Selection Control 0) ........ 237
CCPTMRS1 (PWM Timer Selection Control 1) ........ 237
CCPxAS (CCPx Auto-Shutdown Control)................. 238
CCPxCON (ECCPx Control)..................................... 236
CMOUT (Comparator Output)................................... 186
CMxCON0 (Cx Control) ............................................ 185
CMxCON1 (Cx Control 1) ......................................... 186
Configuration Word 1 .................................................. 62
Configuration Word 2 .................................................. 64
CPSCON0 (Capacitive Sensing Control Register 0) 325
CPSCON1 (Capacitive Sensing Control Register 1) 326
DACCON0 ................................................................ 178
DACCON1 ................................................................ 178
EEADRL (EEPROM Address).................................. 128
EECON1 (EEPROM Control 1) ................................ 129
EECON2 (EEPROM Control 2) ................................ 130
EEDATH (EEPROM Data) ....................................... 128
EEDATL (EEPROM Data)........................................ 128
FVRCON .................................................................. 158
INTCON (Interrupt Control) ...................................... 100
IOCBF (Interrupt-on-Change Flag)........................... 154
IOCBN (Interrupt-on-Change Negative Edge).......... 154
IOCBP (Interrupt-on-Change Positive Edge)............ 154
LATA (Data Latch PORTA) ...................................... 135
LATB (Data Latch PORTB) ...................................... 140
LATC (Data Latch PORTC) ...................................... 144
LATD (Data Latch PORTD) ...................................... 147
LATE (Data Latch PORTE) ...................................... 151
LCDCON (LCD Control) ........................................... 331
LCDCST (LCD Contrast Control) ............................. 334
LCDDATAx (LCD Data).................................... 335, 342
LCDPS (LCD Phase)................................................ 332
LCDREF (LCD Reference Voltage Control) ............. 333
LCDRL (LCD Reference Voltage Control)................ 342
LCDSEn (LCD Segment Enable) ............................. 335
OPTION_REG (OPTION)......................................... 195
OSCCON (Oscillator Control)..................................... 83
OSCSTAT (Oscillator Status) ..................................... 84
OSCTUNE (Oscillator Tuning).................................... 85
PCON (Power Control Register)................................. 93
PCON (Power Control) ............................................... 93
PIE1 (Peripheral Interrupt Enable 1) ........................ 101
PIE2 (Peripheral Interrupt Enable 2) ........................ 102
PIE3 (Peripheral Interrupt Enable 3) ........................ 103
PIR1 (Peripheral Interrupt Register 1) ...................... 104
PIR2 (Peripheral Interrupt Request 2) ...................... 105
PIR3 (Peripheral Interrupt Request 3) ...................... 106
PORTA ..................................................................... 135
PORTB ..................................................................... 140
PORTC ..................................................................... 144
PORTD ..................................................................... 147
PORTE ..................................................................... 150
PSTRxCON (PWM Steering Control) ....................... 240
PWMxCON (Enhanced PWM Control) ..................... 239
RCSTA (Receive Status and Control) ...................... 303
Special Function, Summary........................................ 39
SRCON0 (SR Latch Control 0) ................................. 191
SRCON1 (SR Latch Control 1) ................................. 192
SSPADD (MSSP Address and Baud Rate,
I2C Mode) ......................................................... 292
SSPCON1 (MSSP Control 1) ................................... 289
SSPCON2 (SSP Control 2) ...................................... 290
SSPCON3 (SSP Control 3) ...................................... 291
SSPMSK (SSP Mask) .............................................. 292
SSPSTAT (SSP Status) ........................................... 288
STATUS ..................................................................... 29
T1CON (Timer1 Control) .......................................... 205
T1GCON (Timer1 Gate Control)............................... 206
TRISA (Tri-State PORTA) ........................................ 135
TRISB (Tri-State PORTB) ........................................ 140
TRISC (Tri-State PORTC) ........................................ 144
TRISD (Tri-State PORTD) ........................................ 147
TRISE (Tri-State PORTE) ........................................ 150
TXCON ..................................................................... 211
TXSTA (Transmit Status and Control)...................... 302
PIC16(L)F1934/6/7
DS41364E-page 466 2008-2011 Microchip Technology Inc.
WDTCON (Watchdog Timer Control)........................ 115
WPUB (Weak Pull-up PORTB) .................................141
RESET .............................................................................. 377
Reset................................................................................... 87
Reset Instruction ................................................................. 90
Resets ................................................................................. 87
Associated Registers .................................................. 94
Revision History ................................................................ 461
S
Shoot-through Current ...................................................... 232
Software Simulator (MPLAB SIM)..................................... 443
SPBRG Register ........................................................... 41, 42
SPBRGH ........................................................................... 305
SPBRGL............................................................................ 305
Special Event Trigger........................................................163
Special Function Registers (SFRs) ..................................... 39
SPI Mode (MSSP)
Associated Registers ................................................ 251
SPI Clock .................................................................. 247
SR Latch ...........................................................................189
Associated registers w/ SR Latch .............................192
SRCON0 Register............................................................. 191
SRCON1 Register............................................................. 192
SSPADD Register ....................................................... 43, 292
SSPBUF Register ............................................................... 43
SSPCON Register............................................................... 43
SSPCON1 Register...........................................................289
SSPCON2 Register...........................................................290
SSPCON3 Register...........................................................291
SSPMSK Register.............................................................292
SSPOV.............................................................................. 278
SSPOV Status Flag........................................................... 278
SSPSTAT Register ..................................................... 43, 288
R/W Bit......................................................................257
Stack ................................................................................... 54
Accessing.................................................................... 54
Reset........................................................................... 56
Stack Overflow/Underflow................................................... 90
STATUS Register................................................................ 29
SUBWFB........................................................................... 379
T
T1CON Register.......................................................... 39, 205
T1GCON Register............................................................. 206
T2CON Register............................................................ 39, 47
Temperature Indicator Module .......................................... 173
Thermal Considerations (PIC16F/LF1934/36/37) ............. 394
Timer0 ............................................................................... 193
Associated Registers ................................................ 195
Operation .................................................................. 193
Specifications............................................................ 402
Timer1 ............................................................................... 197
Associated registers.................................................. 207
Asynchronous Counter Mode ................................... 199
Reading and Writing ......................................... 199
Clock Source Selection............................................. 198
Interrupt..................................................................... 201
Operation .................................................................. 198
Operation During Sleep ............................................ 201
Oscillator ................................................................... 199
Prescaler................................................................... 199
Specifications............................................................ 402
Timer1 Gate
Selecting Source............................................... 199
TMR1H Register ....................................................... 197
TMR1L Register........................................................ 197
Timer2
Associated registers ................................................. 212
Timer2/4/6......................................................................... 209
Associated registers ................................................. 212
Timers
Timer1
T1CON ............................................................. 205
T1GCON........................................................... 206
Timer2/4/6
TXCON ............................................................. 211
Timing Diagrams
A/D Conversion......................................................... 404
A/D Conversion (Sleep Mode) .................................. 404
Acknowledge Sequence ........................................... 280
Asynchronous Reception.......................................... 300
Asynchronous Transmission..................................... 296
Asynchronous Transmission (Back to Back) ............ 296
Auto Wake-up Bit (WUE) During Normal Operation . 312
Auto Wake-up Bit (WUE) During Sleep .................... 312
Automatic Baud Rate Calibration.............................. 310
Baud Rate Generator with Clock Arbitration............. 273
BRG Reset Due to SDA Arbitration During Start
Condition .......................................................... 283
Brown-out Reset (BOR)............................................ 400
Brown-out Reset Situations ........................................ 89
Bus Collision During a Repeated Start Condition
(Case 1)............................................................ 284
Bus Collision During a Repeated Start Condition
(Case 2)............................................................ 284
Bus Collision During a Start Condition (SCL = 0) ..... 283
Bus Collision During a Stop Condition (Case 1) ....... 285
Bus Collision During a Stop Condition (Case 2) ....... 285
Bus Collision During Start Condition (SDA only) ...... 282
Bus Collision for Transmit and Acknowledge ........... 281
CLKOUT and I/O ...................................................... 398
Clock Synchronization .............................................. 270
Clock Timing............................................................. 396
Comparator Output ................................................... 179
Enhanced Capture/Compare/PWM (ECCP)............. 402
Fail-Safe Clock Monitor (FSCM)................................. 82
First Start Bit Timing ................................................. 274
Full-Bridge PWM Output........................................... 227
Half-Bridge PWM Output .................................. 225, 232
I2C Bus Data............................................................. 410
I2C Bus Start/Stop Bits ............................................. 409
I2C Master Mode (7-Bit Reception)................... 277, 279
I2C Stop Condition Receive or Transmit Mode......... 280
INT Pin Interrupt ......................................................... 98
Internal Oscillator Switch Timing ................................ 77
LCD Interrupt Timing in Quarter-Duty Cycle Drive ... 358
LCD Sleep Entry/Exit when SLPEN = 1 or CS = 00 . 360
PWM Auto-shutdown................................................ 231
Firmware Restart .............................................. 230
PWM Direction Change ............................................ 228
PWM Direction Change at Near 100% Duty Cycle... 229
PWM Output (Active-High) ....................................... 223
PWM Output (Active-Low) ........................................ 224
Repeat Start Condition ............................................. 275
Reset Start-up Sequence ........................................... 91
Reset, WDT, OST and Power-up Timer ................... 399
Send Break Character Sequence............................. 313
SPI Master Mode (CKE = 1, SMP = 1) ..................... 407
SPI Mode (Master Mode).......................................... 247
SPI Slave Mode (CKE = 0) ....................................... 408
2008-2011 Microchip Technology Inc. DS41364E-page 467
PIC16(L)F1934/6/7
SPI Slave Mode (CKE = 1) ....................................... 408
Synchronous Reception (Master Mode, SREN) ....... 317
Synchronous Transmission....................................... 315
Synchronous Transmission (Through TXEN) ........... 315
Timer0 and Timer1 External Clock ........................... 401
Timer1 Incrementing Edge........................................ 201
Two Speed Start-up .................................................... 80
Type-A in 1/2 MUX, 1/2 Bias Drive ........................... 347
Type-A in 1/2 MUX, 1/3 Bias Drive ........................... 349
Type-A in 1/3 MUX, 1/2 Bias Drive ........................... 351
Type-A in 1/3 MUX, 1/3 Bias Drive ........................... 353
Type-A in 1/4 MUX, 1/3 Bias Drive ........................... 355
Type-A/Type-B in Static Drive................................... 346
Type-B in 1/2 MUX, 1/2 Bias Drive ........................... 348
Type-B in 1/2 MUX, 1/3 Bias Drive ........................... 350
Type-B in 1/3 MUX, 1/2 Bias Drive ........................... 352
Type-B in 1/3 MUX, 1/3 Bias Drive ........................... 354
Type-B in 1/4 MUX, 1/3 Bias Drive ........................... 356
USART Synchronous Receive (Master/Slave) ......... 406
USART Synchronous Transmission (Master/Slave) . 405
Wake-up from Interrupt............................................. 112
Timing Diagrams and Specifications
PLL Clock.................................................................. 397
Timing Parameter Symbology........................................... 395
Timing Requirements
I2C Bus Data ............................................................. 411
I2C Bus Start/Stop Bits ............................................. 410
SPI Mode .................................................................. 409
TMR0 Register.................................................................... 39
TMR1H Register ................................................................. 39
TMR1L Register.................................................................. 39
TMR2 Register.............................................................. 39, 47
TRIS.................................................................................. 380
TRISA Register ........................................................... 40, 135
TRISB ............................................................................... 138
TRISB Register ........................................................... 40, 140
TRISC ............................................................................... 143
TRISC Register........................................................... 40, 144
TRISD ............................................................................... 146
TRISD Register........................................................... 40, 147
TRISE ............................................................................... 149
TRISE Register ........................................................... 40, 150
Two-Speed Clock Start-up Mode ........................................ 79
TXCON (Timer2/4/6) Register .......................................... 211
TXREG.............................................................................. 295
TXREG Register ................................................................. 42
TXSTA Register .......................................................... 42, 302
BRGH Bit .................................................................. 305
U
USART
Synchronous Master Mode
Requirements, Synchronous Receive .............. 406
Requirements, Synchronous Transmission ...... 406
Timing Diagram, Synchronous Receive ........... 406
Timing Diagram, Synchronous Transmission ... 405
V
VREF. SEE ADC Reference Voltage
W
Wake-up on Break............................................................ 311
Wake-up Using Interrupts................................................. 112
Watchdog Timer (WDT)...................................................... 90
Associated Registers................................................ 116
Configuration Word w/ Watchdog Timer................... 116
Modes....................................................................... 114
Specifications ........................................................... 401
WCOL....................................................... 273, 276, 278, 280
WCOL Status Flag.................................... 273, 276, 278, 280
WDTCON Register ........................................................... 115
WPUB Register................................................................. 141
Write Protection .................................................................. 65
WWW Address ................................................................. 471
WWW, On-Line Support ..................................................... 14
PIC16(L)F1934/6/7
DS41364E-page 468 2008-2011 Microchip Technology Inc.
NOTES:
2008-2011 Microchip Technology Inc. DS41364E-page 469
PIC16(L)F1934/6/7
THE MICROCHIP WEB SITE
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com. Under “Support”, click on
“Customer Change Notification” and follow the
registration instructions.
CUSTOMER SUPP ORT
Users of Microchip products can receive assistance
through several channels:
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers should contact their distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical suppo rt is avail able throug h the we b site
at: http://microchip.com/support
PIC16(L)F1934/6/7
DS41364E-page 470 2008-2011 Microchip Technology Inc.
READER RESP ONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip
product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our
documentation can better serve you, please FAX your comments to the Technical Publications Manager at
(480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
TO: Technical Publications Manager
RE: Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
Application (optional):
Would you like a reply? Y N
Device: Literature Number:
Questions:
FAX: (______) _________ - _________
DS41364EPIC16(L)F1934/6/7
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
2008-2011 Microchip Technology Inc. DS41364E-page 471
PIC16(L)F1934/6/7
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
Examples:
a) PIC16LF1937 - I/P = Industrial temp., Plastic
DIP package, low-voltage VDD limits.
b) PIC16F1934 - I/PT = Industrial temp., TQFP
package, standard VDD limits.
Note 1: Tape and Reel identifier only appears in the
catalog part number description. This
identifier is used for ordering purposes and is
not printed on the device package. Check
with your Microchip Sales Office for package
availability with the Tape and Reel option.
PART NO. X/XX XXX
PatternPackageTemperature
Range
Device
[X](1)
Tape and Reel
Option
-
Device: PIC16F1934, PIC16LF1934, PIC16F1934, PIC16LF1934
PIC16F1936, PIC16LF1936, PIC16F1936, PIC16LF1936
PIC16F1937, PIC16LF1937, PIC16F1937, PIC16LF1937
Tape and Reel
Option: Blank = Standard packaging (tube or tray)
T = Tape and Reel(1)
Temperature
Range: I= -40C to +85C
E= -40
C to +125C
Package: ML = Micro Lead Frame (QFN)
MV = Micro Lead Frame (UQFN) 4x4
P=Plastic DIP
PT = TQFP (Thin Quad Flatpack)
SO = SOIC
SP = Skinny Plastic DIP
SS = SSOP
Pattern: 3-Digit Pattern Code for QTP (blank otherwise)
DS41364E-page 472 2008-2011 Microchip Technology Inc.
AMERICAS
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://www.microchip.com/
support
Web Address:
www.microchip.com
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Cleveland
Independence, OH
Tel: 216-447-0464
Fax: 216-447-0643
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Indianapolis
Noblesville, IN
Tel: 317-773-8323
Fax: 317-773-5453
Los A n ge les
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
ASIA/PACIFIC
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8569-7000
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
China - Chongqing
Tel: 86-23-8980-9588
Fax: 86-23-8980-9500
China - Hangzhou
Tel: 86-571-2819-3180
Fax: 86-571-2819-3189
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
ASIA/PACIFIC
India - Bangalore
Tel: 91-80-3090-4444
Fax: 91-80-3090-4123
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
Taiwan - Hsin Chu
Tel: 886-3-6578-300
Fax: 886-3-6578-370
Taiwan - Kaohsiung
Tel: 886-7-213-7830
Fax: 886-7-330-9305
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
EUROPE
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Cop e nha gen
Tel: 45-4450-2828
Fax: 45-4485-2829
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spai n - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
Worldwide Sales and Service
05/02/11