AUIRF2907ZS-7P
HEXFET® Power MOSFET
07/20/10
www.irf.com 1
S
D
G
Features
lAdvanced Process Technology
lUltra Low On-Resistance
l175°C Operating Temperature
lFast Switching
lRepetitive Avalanche Allowed up to Tjmax
lLead-Free, RoHS Compliant
lAutomotive Qualified *
PD - 96321
S (Pin 2, 3, 5, 6, 7)
G (Pin 1)
AUTOMOTIVE GRADE
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
Specifically designed for Automotive applications, this
HEXFET® Power MOSFET utilizes the latest processing
techniques to achieve extremely low on-resistance per silicon
area. Additional features of this design are a 175°C junction
operating temperature, fast switching speed and improved
repetitive avalanche rating . These features combine to make
this design an extremely efficient and reliable device for use
in Automotive applications and a wide variety of other
applications.
Description
Absolute Maximum Ratings
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device.
These are stress ratings only; and functional operation of the device at these or any other condition beyond those
indicated in the specifications is not implied.Exposure to absolute-maximum-rated conditions for extended periods
may affect device reliability. The thermal resistance and power dissipation ratings are measured under board
mounted and still air conditions. Ambient temperature (TA) is 25°C, unless otherwise specified.
GDS
Gate Drain Source
D2P a k 7 P i n
G
SS
D
SS
S
Absolute Maximum Ratin
g
s
Parameter Units
I
D
@ T
C
= 25°C Continuous Drain Current, V
GS
@ 10V (Silicon Limited)
I
D
@ T
C
= 100°C Continuous Drain Current, V
GS
@ 10V (Silicon Limited)
I
DM
Pulsed Drain Current
c
P
D
@
T
C
= 25°C Maximum Power Dissipation W
Linear Derating Factor W/°C
V
GS
Gate-to-Source Voltage V
E
AS
Single Pulse Avalanche Energy (Thermally Limited)
d
mJ
E
AS
(tested) Single Pulse Avalanche Energy Tested Value
g
I
AR
Avalanche Current
c
A
E
AR
Repetitive Avalanche Energy
c
mJ
T
J
Operating Junction and
T
STG
Storage Temperature Range
Soldering Temperature, for 10 seconds (1.6mm from case)
Mounting torque, 6-32 or M3 screw
Thermal Resistance
Parameter Typ. Max. Units
R
θJC
Junction-to-Case
i
––– 0.50
R
θCS
Case-to-Sink, Flat, Greased Surface 0.50 ––
R
θJA
Junction-to-Ambient –– 62
R
θJA
Junction-to-Ambient (PCB Mount, steady state)
h
––– 40
A
°C/W
°C
10 lbf•in (1.1N•m)
300
2.0
± 20
Max.
180
120
700
160
410
See Fig.12a,12b,15,16
300
-55 to + 175
V
(BR)DSS
75V
R
DS(on)
typ. 3.0m
max. 3.8m
j
I
D (Silicon Limited)
180A
AUIRF2907ZS-7P
2www.irf.com
S
D
G
S
D
G
Notes:
Repetitive rating; pulse width limited by
max. junction temperature. (See fig. 11).
Limited by TJmax, starting TJ = 25°C,
L=0.026mH, RG = 25, IAS = 110A, VGS =10V.
Part not recommended for use above this value.
Pulse width 1.0ms; duty cycle 2%.
Coss eff. is a fixed capacitance that gives the same
charging time as Coss while VDS is rising from 0 to 80%
VDSS.
This value determined from sample failure population starting
TJ = 25°C, L=0.026mH, RG = 25, IAS = 110A, VGS =10V.
This is applied to D2Pak, when mounted on 1" square PCB
( FR-4 or G-10 Material ). For recommended footprint and
soldering techniques refer to application note #AN-994.
Rθ is measured at TJ of approximately 90°C.
Solder mounted on IMS substrate.
Static Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Parameter Min. T
y
p. Max. Units
V(BR)DSS Drain-to-Source Breakdown Volta
g
e 75 ––– –– V
∆ΒVDSS
/
TJ Breakdown Volta
g
e Temp. Coefficient ––– 0.066 ––– V/°C
RDS(on) SMD Static Drain-to-Source On-Resistance ––– 3.0 3.8 m
VGS(th) Gate Threshold Volta
g
e 2.0 –– 4.0 V
g
fs Forward Transconductance 94 ––– –– S
IDSS Drain-to-Source Leaka
e Current ––– ––– 20
µ
A
––– ––– 250
IGSS Gate-to-Source Forward Leaka
g
e ––– ––– 200 nA
Gate-to-Source Reverse Leaka
g
e ––– ––– -200
Dynamic Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Parameter Min. T
y
p. Max. Units
QgTotal Gate Char
g
e –– 170 260
Qgs Gate-to-Source Char
g
e ––– 55 ––
Qgd Gate-to-Drain ("Miller") Char
g
e ––– 66 ––
td(on) Turn-On Dela
y
Time –21–
trRise Time –90–
td(off) Turn-Off Dela
y
Time –92–
tfFall Time –44–
LDInternal Drain Inductance Between lead,
6mm (0.25in.)
LSInternal Source Inductance from packa
g
e
and center of die contact
Ciss Input Capacitance ––– 7580 –––
Coss Output Capacitance ––– 970 ––
Crss Reverse Transfer Capacitance ––– 540 –––
Coss Output Capacitance ––– 3750 –––
Coss Output Capacitance ––– 650 ––
Coss eff. Effective Output Capacitance
f
–1110–
Diode Characteristics
Parameter Min. T
y
p. Max. Units
ISContinuous Source Current
(Body Diode)
ISM Pulsed Source Current
(Body Diode)
c
VSD Diode Forward Voltage ––– –– 1.3 V
trr Reverse Recovery Time ––– 35 53 ns
Qrr Reverse Recover
y
Char
g
e ––– 40 60 nC
ton Forward Turn-On Time
Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
VDS = VGS, ID = 250µA
VDS = 75V, VGS = 0V
VDS = 75V, VGS = 0V, TJ = 125°C
Conditions
VGS = 0V, ID = 250µA
Reference to 25°C, ID = 1mA
VGS = 10V, ID = 110A
e
T
J
= 25°C, I
F
= 110A, VDD = 38V
di/dt = 100A/
µ
s
e
T
J
= 25°C, I
S
= 110A, V
GS
= 0V
e
showing the
integral reverse
p-n junction diode.
VGS = 0V, VDS = 1.0V, ƒ = 1.0MHz
VGS = 10V
e
MOSFET symbol
VGS = 0V
VDS = 25V
VGS = 0V, VDS = 60V, ƒ = 1.0MHz
Conditions
VGS = 0V, VDS = 0V to 60V
ƒ = 1.0MHz, See Fig. 5
RG = 2.6
ID = 110A
VDS = 25V, ID = 110A
VDD = 38V
ID = 110A
VGS = 20V
VGS = -20V
VDS = 60V
VGS = 10V
e
Conditions
nC
ns
nH
pF
–––
–––
–––
–––
––– ––
––– ––
700
4.5
7.5
A
160
AUIRF2907ZS-7P
www.irf.com 3
Qualification standards can be found at International Rectifiers web site: http//www.irf.com/
 Exceptions to AEC-Q101 requirements are noted in the qualification report.
Qualification Information
D2 PAK 7 Pin MSL1
Qualification Level
Automotive
(per AEC-Q101)
††
Comments: This part number(s) passed Automotive qualification.
IR’s Industrial and Consumer qualification level is granted by
extension of the higher Automotive level.
Charged Device Model Class C4 (1000V)
(per AEC-Q101-005)
Moisture Sensitivity Level
RoHS Compliant Yes
ESD
Machine Model Class M4(425V)
(per AEC-Q101-002)
Human Body Model Class H2(4000V)
(per AEC-Q101-001)
AUIRF2907ZS-7P
4www.irf.com
Fig 2. Typical Output Characteristics
Fig 1. Typical Output Characteristics
Fig 3. Typical Transfer Characteristics Fig 4. Typical Forward Transconductance
vs. Drain Current
0.1 110 100 1000
VDS, Drain-to-Source Voltage (V)
1
10
100
1000
ID, Drain-to-Source Current (A)
VGS
TOP 15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM 4.5V
60µs PULSE WIDTH
Tj = 25°C
4.5V
0.1 110 100 1000
VDS, Drain-to-Source Voltage (V)
10
100
1000
ID, Drain-to-Source Current (A)
4.5V
60µs PULSE WIDTH
Tj = 175°C
VGS
TOP 15V
10V
8.0V
7.0V
6.0V
5.5V
5.0V
BOTTOM 4.5V
1 2 3 4 5 6 7 8
VGS, Gate-to-Source Voltage (V)
0.1
1
10
100
1000
ID, Drain-to-Source Current (Α)
TJ = 25°C
TJ = 175°C
VDS = 25V
60µs PULSE WIDTH
0 25 50 75 100 125 150
ID,Drain-to-Source Current (A)
0
50
100
150
200
Gfs, Forward Transconductance (S)
TJ = 25°C
TJ = 175°C
VDS = 10V
380µs PULSE WIDTH
AUIRF2907ZS-7P
www.irf.com 5
Fig 8. Maximum Safe Operating Area
Fig 6. Typical Gate Charge vs.
Gate-to-Source Voltage
Fig 5. Typical Capacitance vs.
Drain-to-Source Voltage
Fig 7. Typical Source-Drain Diode
Forward Voltage
110 100
VDS, Drain-to-Source Voltage (V)
100
1000
10000
100000
C, Capacitance(pF)
VGS = 0V, f = 1 MHZ
Ciss = C gs + Cgd, C ds SHORTED
Crss = Cgd
Coss = Cds + Cgd
Coss
Crss
Ciss
0 50 100 150 200
QG Total Gate Charge (nC)
0.0
2.0
4.0
6.0
8.0
10.0
12.0
VGS, Gate-to-Source Voltage (V)
VDS= 60V
VDS= 38V
VDS= 15V
ID= 110A
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4
VSD, Source-to-Drain Voltage (V)
0.1
1
10
100
1000
ISD, Reverse Drain Current (A)
TJ = 25°C
TJ = 175°C
VGS = 0V
0.1 1.0 10.0 100.0
VDS, Drain-toSource Voltage (V)
0.1
1
10
100
1000
10000
ID, Drain-to-Source Current (A)
Tc = 25°C
Tj = 175°C
Single Pulse
1msec
10msec
OPERATION IN THIS AREA
LIMITED BY R DS(on)
100µsec
DC
LIMITED BY PACKAGE
AUIRF2907ZS-7P
6www.irf.com
Fig 11. Maximum Effective Transient Thermal Impedance, Junction-to-Case
Fig 9. Maximum Drain Current vs.
Case Temperature
Fig 10. Normalized On-Resistance
vs. Temperature
-60 -40 -20 020 40 60 80 100120140160180
TJ , Junction Temperature (°C)
0.5
1.0
1.5
2.0
2.5
3.0
RDS(on) , Drain-to-Source On Resistance
(Normalized)
ID = 180A
VGS = 10V
1E-006 1E-005 0.0001 0.001 0.01 0.1
t1 , Rectangular Pulse Duration (sec)
0.0001
0.001
0.01
0.1
1
Thermal Response ( Z thJC )
0.20
0.10
D = 0.50
0.02
0.01
0.05
SINGLE PULSE
( THERMAL RESPONSE )
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
Ri (°C/W) τi (sec)
0.1072 0.000096
0.2787 0.002614
0.1143 0.013847
τJ
τJ
τ1
τ1
τ2
τ2τ3
τ3
R1
R1R2
R2R3
R3
τ
τC
Ci i/Ri
Ci= τi/Ri
25 50 75 100 125 150 175
TC , Case Temperature (°C)
0
40
80
120
160
200
ID, Drain Current (A)
AUIRF2907ZS-7P
www.irf.com 7
QG
QGS QGD
VG
Charge
D.U.T. V
DS
I
D
I
G
3mA
V
GS
.3µF
50K
.2µF
12V
Current Regulator
Same Type as D.U.T.
Current Sampling Resistors
+
-
10 V
Fig 13b. Gate Charge Test Circuit
Fig 13a. Basic Gate Charge Waveform
Fig 12c. Maximum Avalanche Energy
vs. Drain Current
Fig 12b. Unclamped Inductive Waveforms
Fig 12a. Unclamped Inductive Test Circuit
tp
V
(BR)DSS
I
AS
Fig 14. Threshold Voltage vs. Temperature
R
G
I
AS
0.01
t
p
D.U.T
L
VDS
+
-V
DD
DRIVER
A
15V
20V
VGS
25 50 75 100 125 150 175
Starting TJ , Junction Temperature (°C)
0
100
200
300
400
500
600
700
EAS , Single Pulse Avalanche Energy (mJ)
ID
TOP 24A
34A
BOTTOM 110A
-75 -50 -25 025 50 75 100 125 150 175 200
TJ , Temperature ( °C )
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VGS(th) Gate threshold Voltage (V)
ID = 250µA
ID = 1.0mA
ID = 1.0A
AUIRF2907ZS-7P
8www.irf.com
Fig 15. Typical Avalanche Current vs.Pulsewidth
Fig 16. Maximum Avalanche Energy
vs. Temperature
Notes on Repetitive Avalanche Curves , Figures 15, 16:
(For further info, see AN-1005 at www.irf.com)
1. Avalanche failures assumption:
Purely a thermal phenomenon and failure occurs at a
temperature far in excess of Tjmax. This is validated for
every part type.
2. Safe operation in Avalanche is allowed as long asTjmax is
not exceeded.
3. Equation below based on circuit and waveforms shown in
Figures 12a, 12b.
4. PD (ave) = Average power dissipation per single
avalanche pulse.
5. BV = Rated breakdown voltage (1.3 factor accounts for
voltage increase during avalanche).
6. Iav = Allowable avalanche current.
7. T = Allowable rise in junction temperature, not to exceed
Tjmax (assumed as 25°C in Figure 15, 16).
tav = Average time in avalanche.
D = Duty cycle in avalanche = tav ·f
ZthJC(D, tav) = Transient thermal resistance, see figure 11)
PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC
Iav = 2DT/ [1.3·BV·Zth]
EAS (AR) = PD (ave)·tav
1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01
tav (sec)
1
10
100
1000
Avalanche Current (A)
0.05
Duty Cycle = Single Pulse
0.10
Allowed avalanche Current vs
avalanche pulsewidth, tav
assuming Tj = 25°C due to
avalanche losses
0.01
25 50 75 100 125 150 175
Starting TJ , Junction Temperature (°C)
0
50
100
150
200
EAR , Avalanche Energy (mJ)
TOP Single Pulse
BOTTOM 1% Duty Cycle
ID = 110A
AUIRF2907ZS-7P
www.irf.com 9
Fig 17. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
VDS
90%
10%
VGS
t
d(on)
t
r
t
d(off)
t
f
VDS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
RD
VGS
RG
D.U.T.
10V
+
-
VDD
Fig 18a. Switching Time Test Circuit
Fig 18b. Switching Time Waveforms
Circuit Layout Considerations
Low Stray Inductance
Ground Plane
Low Leakage Inductance
Current Transformer
P.W. Period
di/dt
Diode Recovery
dv/dt
Ripple 5%
Body Diode Forward Drop
Re-Applied
Voltage
Reverse
Recovery
Current
Body Diode Forward
Current
V
GS
=10V
V
DD
I
SD
Driver Gate Drive
D.U.T. I
SD
Waveform
D.U.T. V
DS
Waveform
Inductor Curent
D = P. W .
Period
* VGS = 5V for Logic Level Devices
*
+
-
+
+
+
-
-
-
RGVDD
dv/dt controlled by RG
Driver same type as D.U.T.
ISD controlled by Duty Factor "D"
D.U.T. - Device Under Test
D.U.T
AUIRF2907ZS-7P
10 www.irf.com
D2Pak - 7 Pin Package Outline
Dimensions are shown in millimeters (inches)
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
D2Pak - 7 Pin Part Marking Information
YWWA
XX or XX
Part Number
IR Logo
Lot Code
AUIRF2907ZS-7
Date Code
Y= Year
WW= Work Week
A= Automotive, Lead Free
AUIRF2907ZS-7P
www.irf.com 11
D2Pak - 7 Pin Tape and Reel
AUIRF2907ZS-7P
12 www.irf.com
Ordering Information
Base
p
art number Packa
g
e T
yp
e Standard Pac
k
Com
p
lete Part Number
Form Quantit
y
AUIRF2907ZS-7P D2Pak Tube 50 AUIRF2907ZS-7P
Tape and Reel Left 800 AUIRF2907ZS7PTL
Tape and Reel Right 800 AUIRF2907ZS7PTR
AUIRF2907ZS-7P
www.irf.com 13
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make
corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any
product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific
requirements with regards to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions
of sale supplied at the time of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty.
Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by
government requirements, testing of all parameters of each product is not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications
using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and
operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive
business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express
and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible
or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other
applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where
personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer
shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims,
costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated
with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are specifically
designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade meet military specifications. Buyers
acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely at the Buyer’s risk, and that
they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated
by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree
that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements
For technical support, please contact IR’s Technical Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105