MCP4011T-103E/MC - Microchip Technology

MCP4011/2/3/4

Features

• Volatile Digital Potentiometer in SOT-23, SOIC,

MSOP and DFN packages

• 64 Taps: 63 Resistors with Taps to terminal A and

terminal B

• Simple Up/Down (U/D) Protocol

• Power-on Recall of Default Wiper Setting

- Custom POR wiper settings available

(contact factory)

• Resistance Values: 2.1 kΩ, 5 kΩ, 10 kΩ or 50 kΩ

• Low Tempco:

- Absolute (Rheostat): 50 ppm (0°C to 70°C typ.)

- Ratiometric (Potentiometer): 10 ppm (typ.)

• Low Wiper Resistance: 75Ω (typ.)

• High-Voltage Tolerant Digital Inputs: Up to 12.5V

• Low-Power Operation: 1 µA Max Static Current

• Wide Operating Voltage Range:

- 1.8V to 5.5V - Device Operation

- 2.7V to 5.5V - Resistor Characteristics

Specified

• Extended Temperature Range: -40°C to +125°C

• Wide Bandwidth (-3 dB) Operation:

- 4 MHz (typ.) for 2.1 kΩ device

Description

The MCP4011/2/3/4 devices are volatile, 6-bit Digital

Potentiometers that can be configured as either a

potentiometer or rheostat. The wiper setting is

controlled through a simple Up/Down (U/D) serial

interface.

Package Types

Block Diagram

Device Features

MCP4011

SOIC, MSOP, DFN

MCP4012

SOT-23-6

MCP4013

SOT-23-6

MCP4014

SOT-23-5

RheostatPotentiometer

Potentiometer Rheostat

VSS

VDD U/D

VDD

VSS

U/D

VDD

VSS

U/D

VDD

VSS

U/D

VDD

VSS

U/D

(Resistor Array)

Wiper Register

2-Wire

Interface

and

Control

Logic

Power-Up

and

Brown-Out

Control

Device Wiper

Configuration

Memory

Type

POR Wiper

Setting

Resistance (typical)

# of

Steps

VDD

Operating

Range (2)

Control

Interface

WiperLock™

Technology

Options (kΩ)Wiper

(Ω)

MCP4011 Potentiometer

(1) RAM Mid-Scale 2.1, 5.0, 10.0, 50.0 75 64 1.8V to 5.5V U/D No

MCP4012 Rheostat RAM Mid-Scale 2.1, 5.0, 10.0, 50.0 75 64 1.8V to 5.5V U/D No

MCP4013 Potentiometer RAM Mid-Scale 2.1, 5.0, 10.0, 50.0 75 64 1.8V to 5.5V U/D No

MCP4014 Rheostat RAM Mid-Scale 2.1, 5.0, 10.0, 50.0 75 64 1.8V to 5.5V U/D No

Note 1: Floating either terminal (A or B) allows the device to be used in Rheostat mode.

2: Analog characteristics (resistor) tested from 2.7V to 5.5V.

Low-Cost 64-Step Volatile Digital POT

MCP4011/2/3/4

1.0 ELECTRICAL

CHARACTERISTICS

Absolute Maximum Ratings †

VDD ............................................................................................................. 6.5V

CS and U/D inputs w.r.t VSS.................................... -0.3V to 12.5V

A,B and W terminals w.r.t VSS..................... -0.3V to VDD + 0.3V

Current at Input Pins ..................................................±10 mA

Current at Supply Pins ...............................................±10 mA

Current at Potentiometer Pins ...................................±2.5 mA

Storage temperature .....................................-65°C to +150°C

Ambient temp. with power applied ................-55°C to +125°C

ESD protection on all pins ........... ≥ 4kV (HBM), ≥ 400V (MM)

Maximum Junction Temperature (TJ) . .........................+150°C

† Notice: Stresses above those listed under “Maximum

Ratings” may cause permanent damage to the device. This is

a stress rating only and functional operation of the device at

those or any other conditions above those indicated in the

operational listings of this specification is not implied.

Exposure to maximum rating conditions for extended periods

may affect device reliability.

AC/DC CHARACTERISTICS

Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.

TA = -40°C to +125°C, 2.1 kΩ, 5kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for VDD = 2.7V to 5.5V,

VSS = 0V, TA = +25°C.

Parameters Sym Min Typ Max Units Conditions

Operating Voltage Range VDD 2.7 — 5.5 V

VDD —1.8 — VV

DD = 1.8V, CS:VIHH = 8.5V,

VIH = 1.8V, VIL = 0V,

U/D:VIH = 1.8V, VIL = 0V

CS Input Voltage VCS V

SS — 12.5 V The CS pin will be at one of three

input levels (VIL, VIH or VIHH).

(Note 6)

Supply Current IDD —45 — µA5.5V, CS = VSS, fU/D = 1 MHz

—15 — µA2.7V, CS

= VSS, fU/D = 1 MHz

— 0.3 1 µA Serial Interface Inactive

(CS = VIH, U/D = VIH)

Resistance

(± 20%)

RAB 1.68 2.1 2.52 kΩ-202 devices (Note 1)

4.0 5 6.0 kΩ-502 devices (Note 1)

8.0 10 12.0 kΩ-103 devices (Note 1)

40.0 50 60.0 kΩ-503 devices (Note 1)

Note 1: Resistance is defined as the resistance between terminal A to terminal B.

2: INL and DNL are measured at VW with VA = VDD and VB = VSS. (-202 devices VA = 4V).

3: MCP4011/13 only, test conditions are: IW = 1.9 mA, code = 00h.

4: MCP4012/14 only, test conditions are:

5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.

6: This specification by design.

7: Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and temperature. See

Section 6.0 “Resistor” for additional information.

8: For voltages below 2.7V, refer to Section 2.0 “Typical Performance Curves”.

9: The MCP4011 is externally connected to match the configurations of the MCP4012 and MCP4014 and then tested.

Device

Resistance

Current at Voltage

Comments

5.5V 2.7V

2.1 kΩ2.25 mA 1.1 mA MCP4012 includes VWZSE

MCP4014 includes VWFSE

5kΩ1.4 mA 450 µA

10 kΩ450 µA 210 µA

50 kΩ90 µA 40 µA

MCP4011/2/3/4

Resolution N 64 Taps No Missing Codes

Step Resistance RS—RAB / 63 — Ω Note 6

Wiper Resistance (Note 3, Note 4) RW— 70 125 Ω5.5V

— 70 325 Ω2.7V

Nominal Resistance Tempco ΔR/ΔT — 50 — ppm/°C TA = -20°C to +70°C

— 100 — ppm/°C TA = -40°C to +85°C

— 150 — ppm/°C TA = -40°C to +125°C

Ratiometeric Tempco ΔVWA/Δ

— 10 — ppm/°C MCP4011 and MCP4013 only,

code = 1Fh

Full-Scale Error (MCP4011/13 only) VWFSE -0.5 -0.1 +0.5 LSb Code 3Fh, 2.7V ≤ VDD ≤ 5.5V

Zero-Scale Error (MCP4011/13 only) VWZSE -0.5 +0.1 +0.5 LSb Code 00h, 2.7V ≤ VDD ≤ 5.5V

Monotonicity N Yes Bits

Resistor Terminal Input Voltage Range

(Terminals A, B and W)

VA,VW,

Vss — VDD VNote 5, Note 6

Current through A, W or B IW—— 2.5 mANote 6

Leakage current into A, W or B IWL —100 — nAMCP4011 A = W = B = VSS

—100 — nAMCP4012/13 A = W = VSS

—100 — nAMCP4014 W = VSS

Capacitance (PA)C

AW — 75 — pF f =1 MHz, code = 1Fh

Capacitance (Pw)C

W— 120 — pF f =1 MHz, code = 1Fh

Capacitance (PB)C

BW — 75 — pF f =1 MHz, code = 1Fh

Bandwidth -3 dB BW — 4 — MHz -202

devices

Code = 1F,

output load = 30 pF

— 2 — MHz -502

devices

— 1 — MHz -103

devices

—200 —kHz -503

devices

AC/DC CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.

TA = -40°C to +125°C, 2.1 kΩ, 5kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for VDD = 2.7V to 5.5V,

VSS = 0V, TA = +25°C.

Parameters Sym Min Typ Max Units Conditions

Note 1: Resistance is defined as the resistance between terminal A to terminal B.

2: INL and DNL are measured at VW with VA = VDD and VB = VSS. (-202 devices VA = 4V).

3: MCP4011/13 only, test conditions are: IW = 1.9 mA, code = 00h.

4: MCP4012/14 only, test conditions are:

5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.

6: This specification by design.

7: Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and temperature. See

Section 6.0 “Resistor” for additional information.

8: For voltages below 2.7V, refer to Section 2.0 “Typical Performance Curves”.

9: The MCP4011 is externally connected to match the configurations of the MCP4012 and MCP4014 and then tested.

Device

Resistance

Current at Voltage

Comments

5.5V 2.7V

2.1 kΩ2.25 mA 1.1 mA MCP4012 includes VWZSE

MCP4014 includes VWFSE

5kΩ1.4 mA 450 µA

10 kΩ450 µA 210 µA

50 kΩ90 µA 40 µA

MCP4011/2/3/4
DS21978C-page 4 © 2006 Microchip Technology Inc.
Potentiometer Integral Non-linearity INL -0.5 ±0.25 +0.5 LSb MCP4011/13 only (Note 2)
Potentiometer Differential Non-linearity DNL -0.5 ±0.25 +0.5 LSb MCP4011/13 only (Note 2)
Rheostat Integral Non-linearity 
MCP4011 (Note 4, Note 9) 
MCP4012 and MCP4014  (Note 4) 
R-INL -0.5 ±0.25 +0.5 LSb -202
devices
(2.1 kΩ)
5.5V
-8.5 +4.5 +8.5 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
-0.5 ±0.25 +0.5 LSb -502
devices
(5 kΩ)
5.5V
-5.5 +2.5 +5.5 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
-0.5 ±0.25 +0.5 LSb -103
devices
(10 kΩ)
5.5V
-3 +1 +3 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
-0.5 ±0.25 +0.5 LSb -503
devices
(50 kΩ)
5.5V
-1 +0.25 +1 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
Rheostat Differential Non-linearity 
MCP4011 (Note 4, Note 9) 
MCP4012 and MCP4014  (Note 4) 
R-DNL -0.5 ±0.25 +0.5 LSb -202
devices
(2.1 kΩ)
5.5V
-1 +0.5 +2 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
-0.5 ±0.25 +0.5 LSb -502
devices
(5 kΩ)
5.5V
-1 +0.25 +1.25 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
-0.5 ±0.25 +0.5 LSb -103
devices
(10 kΩ)
5.5V
-1 0+1 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
-0.5 ±0.25 +0.5 LSb -503
devices
(50 kΩ)
5.5V
-0.5 0+0.5 LSb 2.7V (Note 7)
See Section 2.0  LSb 1.8V (Note 7, Note 8)
AC/DC CHARACTERISTICS (CONTINUED)
Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.
TA = -40°C to +125°C, 2.1 kΩ, 5kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for  VDD = 2.7V to 5.5V,
VSS = 0V, TA = +25°C.
Parameters Sym Min Typ Max Units Conditions
Note 1: Resistance is defined as the resistance between terminal A to terminal B.
2: INL and DNL are measured at VW with VA = VDD and VB = VSS. (-202 devices VA = 4V).
3: MCP4011/13 only, test conditions are: IW = 1.9 mA, code = 00h.
4: MCP4012/14 only, test conditions are:    
5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.
6: This specification by design.
7: Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and temperature. See 
Section 6.0 “Resistor” for additional information.
8: For voltages below 2.7V, refer to Section 2.0 “Typical Performance Curves”.
9: The MCP4011 is externally connected to match the configurations of the MCP4012 and MCP4014 and then tested.
Device 
Resistance
Current at Voltage 
Comments
5.5V 2.7V
2.1 kΩ2.25 mA 1.1 mA MCP4012 includes VWZSE 
MCP4014 includes VWFSE 
5kΩ1.4 mA 450 µA
10 kΩ450 µA 210 µA
50 kΩ90 µA 40 µA

MCP4011/2/3/4

Digital Inputs/Outputs (CS, U/D)

Input High Voltage VIH 0.7 VDD ——V

Input Low Voltage VIL ——0.3V

DD V

High-Voltage Input Entry Voltage VIHH 8.5 — 12.5 (6) V Threshold for WiperLock™

Technology

High-Voltage Input Exit Voltage VIHH ——V

DD+0.8(6) V

CS Pull-up/Pull-down Resistance RCS —16 — kΩVDD = 5.5V, VCS = 3V

CS Weak Pull-up/Pull-down Current IPU —170 — µAV

DD = 5.5V, VCS = 3V

Input Leakage Current IIL -1 — 1 µA VIN = VDD

CS and U/D Pin Capacitance CIN,

COUT

—10 — pFf

C = 1 MHz, VDD ≥ 2.7V

RAM (Wiper) Value

Value Range N 0h — 3Fh hex

Default POR Setting N 1Fh hex

Power Requirements

Power Supply Sensitivity

(MCP4011 and MCP4013 only)

PSS — 0.0015 0.0035 %/% VDD = 4.5V to 5.5V, VA = 4.5V,

Code = 1Fh

— 0.0015 0.0035 %/% VDD = 2.7V to 4.5V, VA = 2.7V,

Code = 1Fh

AC/DC CHARACTERISTICS (CONTINUED)

Electrical Specifications: Unless otherwise indicated, all parameters apply across the specified operating ranges.

TA = -40°C to +125°C, 2.1 kΩ, 5kΩ, 10 kΩ and 50 kΩ devices. Typical specifications represent values for VDD = 2.7V to 5.5V,

VSS = 0V, TA = +25°C.

Parameters Sym Min Typ Max Units Conditions

Note 1: Resistance is defined as the resistance between terminal A to terminal B.

2: INL and DNL are measured at VW with VA = VDD and VB = VSS. (-202 devices VA = 4V).

3: MCP4011/13 only, test conditions are: IW = 1.9 mA, code = 00h.

4: MCP4012/14 only, test conditions are:

5: Resistor terminals A, W and B’s polarity with respect to each other is not restricted.

6: This specification by design.

7: Non-linearity is affected by wiper resistance (RW), which changes significantly over voltage and temperature. See

Section 6.0 “Resistor” for additional information.

8: For voltages below 2.7V, refer to Section 2.0 “Typical Performance Curves”.

9: The MCP4011 is externally connected to match the configurations of the MCP4012 and MCP4014 and then tested.

Device

Resistance

Current at Voltage

Comments

5.5V 2.7V

2.1 kΩ2.25 mA 1.1 mA MCP4012 includes VWZSE

MCP4014 includes VWFSE

5kΩ1.4 mA 450 µA

10 kΩ450 µA 210 µA

50 kΩ90 µA 40 µA

MCP4011/2/3/4

FIGURE 1-1: Increment Timing Waveform.

U/D

tLCUR

tLO

tHI

tLUC

tCSHI

1/fUD

tCSLO

tLCUF

tLUC tLCUF

SERIAL TIMING CHARACTERISTICS

Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges.

Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C.

Parameters Sym Min Typ Max Units Conditions

CS Low Time tCSLO 5——µs

CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V

———ns1.8V ≤ VDD < 2.7V

U/D to CS Hold Time tLUC 500 — — ns 2.7V ≤ VDD ≤ 5.5V

750 — — ns 1.8V ≤ VDD < 2.7V

CS to U/D Low Setup Time tLCUF 500 — — ns

CS to U/D High Setup Time tLCUR 3——µs

U/D High Time tHI 500 — — ns

U/D Low Time tLO 500 — — ns

Up/Down Toggle Frequency fUD —— 1MHz

Wiper Settling Time tS0.5 — — µs 2.1 kΩ, CL = 100 pF

1——µs5kΩ, CL = 100 pF

2——µs10kΩ, CL = 100 pF

10 5 — µs 50 kΩ, CL = 100 pF

Wiper Response on Power-up tPU —200— ns

MCP4011/2/3/4

FIGURE 1-2: Decrement Timing Waveform.

U/D

tLCUR

tHI

tLO

tCSLO

tLUC

tCSHI

tLUC tLCUF

1/fUD

SERIAL TIMING CHARACTERISTICS

Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges.

Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C.

Parameters Sym Min Typ Max Units Conditions

CS Low Time tCSLO 5——µs

CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V

———ns1.8V ≤ VDD < 2.7V

U/D to CS Hold Time tLUC 500 — — ns 2.7V ≤ VDD ≤ 5.5V

750 — — ns 1.8V ≤ VDD < 2.7V

CS to U/D Low Setup Time tLCUF 500 — — ns

CS to U/D High Setup Time tLCUR 3——µs

U/D High Time tHI 500 — — ns

U/D Low Time tLO 500 — — ns

Up/Down Toggle Frequency fUD —— 1MHz

Wiper Settling Time tS0.5 — — µs 2.1 kΩ, CL = 100 pF

1——µs5kΩ, CL = 100 pF

2——µs10kΩ, CL = 100 pF

10 5 — µs 50 kΩ, CL = 100 pF

Wiper Response on Power-up tPU —200— ns

MCP4011/2/3/4

FIGURE 1-3: High-Voltage Increment Timing Waveform.

U/D

tHCUR

tLO

tHI

tHUC

tCSHI

1/fUD

tCSLO

tHCUF

tHUC tHCUF

12V

SERIAL TIMING CHARACTERISTICS

Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges.

Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C.

Parameters Sym Min Typ Max Units Conditions

CS Low Time tCSLO 5——µs

CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V

———ns1.8V ≤ VDD < 2.7V

U/D High Time tHI 500 — — ns

U/D Low Time tLO 500 — — ns

Up/Down Toggle Frequency fUD —— 1MHz

HV U/D to CS Hold Time tHUC 1.5 — — µs

HV CS to U/D Low Setup Time tHCUF 8——µs

HV CS to U/D High Setup Time tHCUR 4.5 — — µs

Wiper Settling Time tS0.5 — — µs 2.1 kΩ, CL = 100 pF

1——µs5kΩ, CL = 100 pF

2——µs10kΩ, CL = 100 pF

10 5 — µs 50 kΩ, CL = 100 pF

Wiper Response on Power-up tPU —200— ns

MCP4011/2/3/4

FIGURE 1-4: High-Voltage Decrement Timing Waveform.

U/D

tHCUR

tHI

tLO

tCSLO

tHUC

tCSHI

tHUC tHCUF

12V

1/fUD

SERIAL TIMING CHARACTERISTICS

Electrical Specifications: Unless otherwise noted, all parameters apply across the specified operating ranges.

Extended (E): VDD = +1.8V to 5.5V, TA = -40°C to +125°C.

Parameters Sym Min Typ Max Units Conditions

CS Low Time tCSLO 5——µs

CS High Time tCSHI 500 — — ns 2.7V ≤ VDD ≤ 5.5V

———ns1.8V ≤ VDD < 2.7V

U/D High Time tHI 500 — — ns

U/D Low Time tLO 500 — — ns

Up/Down Toggle Frequency fUD —— 1MHz

HV U/D to CS Hold Time tHUC 1.5 — — µs

HV CS to U/D Low Setup Time tHCUF 8——µs

HV CS to U/D High Setup Time tHCUR 4.5 — — µs

Wiper Settling Time tS0.5 — — µs 2.1 kΩ, CL = 100 pF

1——µs5kΩ, CL = 100 pF

2——µs10kΩ, CL = 100 pF

10 5 — µs 50 kΩ, CL = 100 pF

Wiper Response on Power-up tPU —200— ns

MCP4011/2/3/4

TEMPERATURE CHARACTERISTICS

Electrical Specifications: Unless otherwise indicated, VDD = +2.7V to +5.5V, VSS =GND.

Parameters Sym Min Typ Max Units Conditions

Temperature Ranges

Specified Temperature Range TA-40 — +125 °C

Operating Temperature Range TA-40 — +125 °C

Storage Temperature Range TA-65 — +150 °C

Thermal Package Resistances

Thermal Resistance, 5L-SOT-23 θJA —70—°C/W

Thermal Resistance, 6L-SOT-23 θJA —120—°C/W

Thermal Resistance, 8L-DFN (2x3) θJA —85—°C/W

Thermal Resistance, 8L-MSOP θJA —206—°C/W

Thermal Resistance, 8L-SOIC θJA —163—°C/W

MCP4011/2/3/4

2.0 TYPICAL PERFORMANCE CURVES

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-1: Device Current (IDD) vs. U/D

Frequency (fU/D) and Ambient Temperature

(VDD = 2.7V and 5.5V).

FIGURE 2-2: Device Current (ISHDN) and

VDD. (CS = VDD) vs. Ambient Temperature.

FIGURE 2-3: CS Pull-up/Pull-down

Resistance (RCS) and Current (ICS) vs. CS Input

Voltage (VCS) (VDD = 5.5V).

FIGURE 2-4: CS High Input Entry/Exit

Threshold vs. Ambient Temperature and VDD.

Note: The graphs and tables provided following this note are a statistical summary based on a limited number of

samples and are provided for informational purposes only. The performance characteristics listed herein

are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified

operating range (e.g., outside specified power supply range) and therefore outside the warranted range.

0.20 0.40 0.60 0.80 1.00

U/D

(MHz)

Device Current (I

) (µA)

2.7V -40°C

2.7V 25°C

2.7V 85°C

2.7V 125°C

5.5V -40°C

5.5V 25°C

5.5V 85°C

5.5V 125°C

0.0

0.1

0.2

0.3

0.4

0.5

0.6

0.7

0.8

-40 25 85 125

Ambient Temperature (°C)

Device Current (I

) (µA)

VDD = 2.7V

VDD = 5.5V

100

150

200

250

987654321

(V)

(kOhms)

-1000

-800

-600

-400

-200

200

400

600

800

1000

(µA)

RCS

ICS

-40 -20 0 20 40 60 80 100 120

Ambient Temperature (°C)

CS V

Threshold (V)

1.8V Entry

2.7V Entry

5.5V Entry

1.8V Exit

2.7V Exit

5.5V Exit

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-5: 2.1 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-6: 2.1 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-7: 2.1 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

FIGURE 2-8: 2.1 k

Rheo Mode – RW

(

), INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-9: 2.1 k

Rheo Mode – RW

(

), INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-10: 2.1 k

Rheo Mode – RW

(

), INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

100

120

140

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.1

-0.075

-0.05

-0.025

0.025

0.05

0.075

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.1

-0.05

0.05

0.1

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

600

700

800

900

1000

1100

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2.75

-2.25

-1.75

-1.25

-0.75

-0.25

0.25

0.75

1.25

1.75

2.25

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

120

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.4

-0.2

0.2

0.4

0.6

0.8

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

600

700

800

900

1000

1100

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-11: 2.1 k

– Nominal

Resistance (

) vs. Ambient Temperature and

VDD.

FIGURE 2-12: 2.1 k

– RWB (

) vs. Wiper

Setting and Ambient Temperature.

2000

2020

2040

2060

2080

-40 0 40 80 120

Ambient Temperature (°C)

Nominal Resistance (R

)

(Ohms)

VDD = 2.7V

VDD = 5.5V

500

1000

1500

2000

2500

0 8 16 24 32 40 48 56 64

Wiper Setting (decimal)

(Ohms)

-40°C

25°C

85°C

125°C

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-13: 2.1 k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 2.7V).

FIGURE 2-14: 2.1 k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 5.5V).

FIGURE 2-15: 2.1 k

– Power-Up Wiper

Response Time.

FIGURE 2-16: 2.1 k

– Low-Voltage

Increment Wiper Settling Time (VDD = 2.7V).

FIGURE 2-17: 2.1 k

– Low-Voltage

Increment Wiper Settling Time (VDD = 5.5V).

WIPER

U/D

WIPER

VDD

U/D

WIPER

U/D

WIPER

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-18: 5k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-19: 5k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-20: 5k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

FIGURE 2-21: 5k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-22: 5k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-23: 5k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

100

120

140

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.1

-0.075

-0.05

-0.025

0.025

0.05

0.075

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

150

200

250

300

350

400

450

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.125

-0.1

-0.075

-0.05

-0.025

0.025

0.05

0.075

0.1

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

500

1000

1500

2000

2500

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2.75

-2.25

-1.75

-1.25

-0.75

-0.25

0.25

0.75

1.25

1.75

2.25

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

120

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.6

-0.4

-0.2

0.2

0.4

0.6

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

600

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-1

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

500

1000

1500

2000

2500

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-24: 5k

– Nominal Resistance

(

) vs. Ambient Temperature and VDD.

FIGURE 2-25: 5k

– RWB (

) vs. Wiper

Setting and Ambient Temperature.

4800

4825

4850

4875

4900

4925

4950

-40 -20 0 20 40 60 80 100 120

Ambient Temperature (°C)

Nominal Resistance (R

)

(Ohms)

VDD = 2.7V

VDD = 5.5V

1000

2000

3000

4000

5000

6000

0 8 16 24 32 40 48 56 64

Wiper Setting (decimal)

(Ohms)

-40°C

25°C

85°C

125°C

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-26: 5k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 2.7V).

FIGURE 2-27: 5k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 5.5V).

FIGURE 2-28: 5k

– Low-Voltage

Increment Wiper Settling Time (VDD = 2.7V).

FIGURE 2-29: 5k

– Low-Voltage

Increment Wiper Settling Time (VDD = 5.5V).

U/D

WIPER

U/D

WIPER

U/D

WIPER

U/D

WIPER

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-30: 10 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-31: 10 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-32: 10 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

FIGURE 2-33: 10 k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-34: 10 k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-35: 10 k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

100

120

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.1

-0.075

-0.05

-0.025

0.025

0.05

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

150

200

250

300

350

400

450

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.125

-0.1

-0.075

-0.05

-0.025

0.025

0.05

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

500

1000

1500

2000

2500

3000

3500

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2.75

-2.25

-1.75

-1.25

-0.75

-0.25

0.25

0.75

1.25

1.75

2.25

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

120

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.15

-0.1

-0.05

0.05

0.1

0.15

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2.5

-1.5

-0.5

0.5

1.5

2.5

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

500

1000

1500

2000

2500

3000

3500

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-36: 10 k

– Nominal Resistance

(

) vs. Ambient Temperature and VDD.

FIGURE 2-37: 10 k

– RWB (

) vs. Wiper

Setting and Ambient Temperature.

10050

10070

10090

10110

10130

10150

10170

10190

10210

10230

10250

-40 -20 0 20 40 60 80 100 120

Ambient Temperature (°C)

Nominal Resistance (R

)

(Ohms)

VDD = 5.5V

VDD = 2.7V

2000

4000

6000

8000

10000

12000

0 8 16 24 32 40 48 56 64

Wiper Setting (decimal)

(Ohms)

-40°C

25°C

85°C

125°C

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-38: 10 k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 2.7V).

FIGURE 2-39: 10 k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 5.5V).

FIGURE 2-40: 10 k

– Low-Voltage

Increment Wiper Settling Time (VDD = 2.7V).

FIGURE 2-41: 10 k

– Low-Voltage

Increment Wiper Settling Time (VDD = 5.5V).

U/D

WIPER

U/D

WIPER

U/D

WIPER

U/D

WIPER

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-42: 50 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-43: 50 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-44: 50 k

Pot Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

FIGURE 2-45: 50 k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 5.5V).

FIGURE 2-46: 50 k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 2.7V).

FIGURE 2-47: 50 k

Rheo Mode – RW (

INL (LSb), DNL (LSb) vs. Wiper Setting and

Ambient Temperature (VDD = 1.8V).

120

160

200

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.15

-0.1

-0.05

0.05

0.1

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

600

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.1

-0.075

-0.05

-0.025

0.025

0.05

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

11000

12000

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

150

200

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-0.1

-0.05

0.05

0.1

0.15

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

100

200

300

400

500

600

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-1.5

-1

-0.5

0.5

1.5

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

1000

2000

3000

4000

5000

6000

7000

8000

9000

10000

11000

12000

0 8 16 24 32 40 48 56

Wiper Setting (decimal)

Wiper Resistance

(Rw)(ohms)

-2

Error (LSb)

-40C Rw 25C Rw 85C Rw 125C Rw

-40C INL 25C INL 85C INL 125C INL

-40C DNL 25C DNL 85C DNL 125C DNL

INL

DNL

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-48: 50 k

– Nominal Resistance

(

) vs. Ambient Temperature and VDD.

FIGURE 2-49: 50 k

– RWB (

) vs. Wiper

Setting and Ambient Temperature.

48000

48200

48400

48600

48800

49000

49200

49400

49600

49800

-40 -20 0 20 40 60 80 100 120

Ambient Temperature (°C)

Nominal Resistance (R

)

(Ohms)

VDD = 2.7V

VDD = 5.5V

10000

20000

30000

40000

50000

60000

0 8 16 24 32 40 48 56 64

Wiper Setting (decimal)

(Ohms)

-40C

25C

85C

125C

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-50: 50 k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 2.7V).

FIGURE 2-51: 50 k

– Low-Voltage

Decrement Wiper Settling Time (VDD = 5.5V).

FIGURE 2-52: 50 k

– Power-Up Wiper

Response Time.

FIGURE 2-53: 50 k

– Low-Voltage

Increment Wiper Settling Time (VDD = 2.7V).

FIGURE 2-54: 50 k

- Low-Voltage

Increment Wiper Settling Time (VDD = 5.5V).

U/D

WIPER

U/D

WIPER

VDD

WIPER

U/D

WIPER

U/D

WIPER

MCP4011/2/3/4

Note: Unless otherwise indicated, TA = +25°C, VDD = 5V, VSS = 0V.

FIGURE 2-55: -3 dB Bandwidth vs.

Temperature.

FIGURE 2-56: -3 dB Bandwidth Test

Circuit.

0.5

1.5

2.5

3.5

4.5

-40 25 125

Temperature (°C)

-3dB Frequency (MHz)

2.1 k

5 k

10 k

50 k

VIN

+5V

VOUT

2.5V DC

Offset

Gnd

DUT

MCP4011/2/3/4

3.0 PIN DESCRIPTIONS

The descriptions of the pins are listed in Table 3-1.

TABLE 3-1: PIN FUNCTION TABLE

3.1 Positive Power Supply Input (VDD)

The VDD pin is the device’s positive power supply input.

The input power supply is relative to VSS and can range

from 1.8V to 5.5V. A decoupling capacitor on VDD (to

VSS) is recommended to achieve maximum

performance.

3.2 Ground (VSS)

The VSS pin is the device ground reference.

3.3 Potentiometer Terminal A

The terminal A pin is connected to the internal potenti-

ometer’s terminal A (available on some devices). The

potentiometer’s terminal A is the fixed connection to the

0x3F terminal of the digital potentiometer.

The terminal A pin is available on the MCP4011,

MCP4012 and MCP4013 devices. The terminal A pin

does not have a polarity relative to the terminal W or B

pins. The terminal A pin can support both positive and

negative current. The voltage on terminal A must be

between VSS and VDD.

The terminal A pin is not available on the MCP4014.

The potentiometer’s terminal A is internally floating.

3.4 Potentiometer Wiper (W) Terminal

The terminal W pin is connected to the internal potenti-

ometer’s terminal W (the wiper). The wiper terminal is

the adjustable terminal of the digital potentiometer. The

terminal W pin does not have a polarity relative to

terminals A or B pins. The terminal W pin can support

both positive and negative current. The voltage on

terminal W must be between VSS and VDD.

3.5 Potentiometer Terminal B

The terminal B pin is connected to the internal potenti-

ometer’s terminal B (available on some devices). The

potentiometer’s terminal B is the fixed connection to the

0x00 terminal of the digital potentiometer.

The terminal B pin is available on the MCP4011 device.

The terminal B pin does not have a polarity relative to

the terminal W or A pins. The terminal B pin can

support both positive and negative current. The voltage

on terminal B must be between VSS and VDD.

The terminal B pin is not available on the MCP4012,

MCP4013 and MCP4014 devices.

For the MCP4013 and MCP4014, the internal potenti-

ometer’s terminal B is internally connected to VSS.

Terminal B does not have a polarity relative to

terminals W or A. Terminal B can support both positive

and negative current.

For the MCP4012, terminal B is internally floating.

Pin Number

Symbol Pin

Type

Buffer

Type Function

MCP4011

(SOIC-8)

MCP4012

MCP4013

(SOT-23-6)

MCP4014

(SOT-23-5)

111V

DD P — Positive Power Supply Input

222V

SS P — Ground

3 6 — A I/O A Potentiometer Terminal A

4 5 5 W I/O A Potentiometer Wiper Terminal

544CS

I TTL Chip Select Input

6 — — B I/O A Potentiometer Terminal B

7 — — NC — — No Connection

833U/D

I TTL Increment/Decrement Input

Legend: TTL = TTL compatible input A = Analog input

I = Input O = Output

P = Power

MCP4011/2/3/4

3.6 Chip Select (CS)

The CS pin is the chip select input. Forcing the CS pin

to VIL enables the serial commands. These commands

can increment and decrement the wiper. Forcing the

CS pin to VIHH enables the high-voltage serial

commands. These commands can increment and

decrement the wiper and are compatibe with the

MCP402X devices. The wiper is saved to volatile

memory (RAM).

The CS pin has an internal pull-up resistor. The resistor

will become “disabled” when the voltage on the CS pin

is below the VIH level. This means that when the CS pin

is “floating”, the CS pin will be pulled to the VIH level

(serial communication (the U/D pin) is ignored). And

when the CS pin is driven low (VIL), the resistance

becomes very large to reduce the device current

consumption when serial commands are occurring.

See Figure 2-3 for additional information.

3.7 Increment/Decrement (U/D)

The U/D pin input is used to increment or decrement

the wiper on the digital potentiometer. An increment

moves the wiper one step toward terminal A, while a

decrement moves the wiper one step toward

terminal B.

MCP4011/2/3/4

4.0 GENERAL OVERVIEW

The MCP4011/2/3/4 devices are general purpose

digital potentiometers intended to be used in

applications where a programmable resistance with

moderate bandwidth is desired.

Applications generally suited for the MCP4011/2/3/4

devices include:

• Set point or offset trimming

• Sensor calibration

• Selectable gain and offset amplifier designs

• Cost-sensitive mechanical trim pot replacement

The digital potentiometer is available in four nominal

resistances (RAB), where the nominal resistance is

defined as the resistance between terminal A and

terminal B. The four nominal resistances are 2.1 kΩ,

5kΩ, 10 kΩ and 50 kΩ.

There are 63 resistors in a string between terminal A

and terminal B. The wiper can be set to tap onto any of

these 63 resistors thus providing 64 possible settings

(including terminal A and terminal B).

Figure 4-1 shows a block diagram for the resistive

network of the device. Equation 4-1 shows the

calculation for the step resistance, while Equation 4-2

illustrates the calculation used to determine the

resistance between the wiper and terminal B.

FIGURE 4-1: Resistor Block Diagram.

EQUATION 4-1: RS CALCULATION

EQUATION 4-2: RWB CALCULATION

1 LSb is the ideal resistance difference between two

successive codes. If we use N = 1 and RW = 0 in

Equation 4-2, we can calculate the step size for each

increment or decrement command.

The MCP4011 device offers a voltage divider

(potentiometer) with all terminals available on pins.

The MCP4012 is a true rheostat, with terminal A and

the wiper (W) of the variable resistor available on pins.

The MCP4013 device offers a voltage divider (potenti-

ometer) with terminal B connected to ground.

The MCP4014 device is a Rheostat device with

terminal A of the resistor floating, terminal B connected

to ground, and the wiper (W) available on pin.

The MCP4011 can be externally configured to

implement any of the MCP4012, MCP4013 or

MCP4014 configurations.

4.1 Serial Interface

A 2-wire synchronous serial protocol is used to

increment or decrement the digital potentiometer’s

wiper terminal. The Increment/Decrement (U/D)

protocol utilizes the CS and U/D input pins. Both inputs

are tolerant of signals up to 12.5V without damaging

the device. The CS pin can differenciate between two

high-voltage levels, VIH and VIHH. This enables

additional commands without requiring additional input

pins. The high-voltage commands (VIHH on the CS pin)

are similar to the standard commands and are

supported for compatability to the MCP401X family of

devices.

The simple U/D protocol uses the state of the U/D pin

at the falling edge of the CS pin to determine if

Increment or Decrement mode is desired. Subsequent

rising edges of the U/D pin move the wiper.

The wiper value will not underflow or overflow.

N = 63

N = 62

N = 61

N = 1

N = 0

RW (1)

01h

Analog

Mux

RW (1)

00h

RW (1)

3Dh

RW (1)

3Eh

RW (1)

3Fh

Note 1: The wiper resistance is tap dependent.

That is, each tap selection resistance

has a small variation. This variation

effects the smaller resistance devices

(2.1 kΩ) more.

RAB

---------=

RWB

RABN

--------------RW

N = 0 to 63 (decimal)

MCP4011/2/3/4

4.2 Power-up

When the device powers up (rising VDD crosses the

Trip Point Voltage (VTP)), the “default” wiper setting is

restored. Table 4 - 1 shows the default value loaded into

the wiper on POR/BOR.

TABLE 4-1: DEFAULT POR WIPER

SETTING SELECTION

While VDD < Vmin (1.8V), the electrical performance

may not meet the data sheet specifications (see

Figure 4-2). The wiper state may be unknown. Also, the

device may be capable of incrementing or decrement-

ing, if a valid command is detected on the CS and U/D

pins.

4.3 Brown Out

If the device VDD is below the specified minimum

voltage, care must be taken to ensure that the CS and

U/D pins do not “create” any of the serial commands.

When the device VDD drops below VMIN (1.8V), the

electrical performance may not meet the data sheet

specifications (see Figure 4-2). The wiper state may be

unknown. Also, the device may be capable of

incrementing or decrementing, if a valid command is

detected on the CS and U/D pins.

When the device voltage rises from below the power-

up trip point (VTP) into the valid operation voltage

range, the wiper state will be forced to the default POR

wiper setting (see Ta ble 4- 1 ).

4.4 Serial Interface Inactive

The serial interface is inactive any time the CS pin is at

VIH and all write cycles are completed.

FIGURE 4-2: Power-up and Brown-out.

Package

Code

Default

POR

Wiper

Setting

Wiper

Code

Typical

RAB Value

-202 Mid-scale 1Fh 2.1 kΩ

-502 Mid-scale 1Fh 5.0 kΩ

-103 Mid-scale 1Fh 10.0 kΩ

-503 Mid-scale 1Fh 50.0 kΩ

VTP

VSS

VDD

1.8V

POR Trip Point (on Rising VDD)

Outside Device Operation

Wiper Forced to Default POR Setting

© 2006 Microchip Technology Inc. DS21978C-page 29
MCP4011/2/3/4
5.0 SERIAL INTERFACE
5.1 Overview
The MCP4011/2/3/4 utilizes a simple 2-wire interface to
increment or decrement the digital potentiometer’s
wiper terminal (W). This interface uses the CS and U/D
pins. The CS pin is the Chip Select input, while the U/D
pin is the Up/Down input. 
The Increment/Decrement protocol enables the device
to move one step at a time through the range of
possible resistance values. The wiper value is
initialized with the “default” value upon power-up. 
A wiper value of 00h connects the wiper to terminal B.
A wiper value of 3Fh connects the wiper to terminal A.
Increment commands move the wiper toward terminal
A, but will not increment to a value greater than 3Fh.
Decrement commands move the wiper toward terminal
B, but will not decrement below 00h.
Refer to Section 1.0 “Electrical Characteristics”,
AC/DC Electrical Characteristics table for detailed input
threshold and timing specifications.
Communication is unidirectional. Therefore, the value
of the current wiper setting cannot be read out of the
MCP401X device.
5.2 Serial Commands
The MCP401X devices support eight serial commands.
Six of these commands are for support and to ease
migration with the MCP402X family of devices. The
commands can be grouped into the following types:
• Serial Commands
• High-voltage Serial Commands
All the commands are shown in Table 5-1.
The command type is determined by the voltage level
the CS pin is driven to. The initial state that the CS pin
must be driven is VIH. From VIH, the two levels that the
CS pin can be driven are:
•V
IL 
•V
IHH 
If the CS pin is driven from VIH to  V
IL, a serial
command is selected. If the CS pin is driven from VIH to
VIHH, a high-voltage serial command is selected. 
Support of the high-voltage serial commands is for
compatiblity with the MCP402X devices. 
TABLE 5-1: COMMANDS        
Command Name High Voltage 
on CS pin?
Increment —
Increment (for MCP402X Compatibility) —
Decrement —
Decrement (for MCP402X Compatibility) —
High-Voltage Increment 1 (for MCP402X Compatibility) Yes
High-Voltage Increment 2 (for MCP402X Compatibility) Yes
High-Voltage Decrement 1 (for MCP402X Compatibility) Yes
High-Voltage Decrement 2 (for MCP402X Compatibility) Yes

MCP4011/2/3/4

5.2.1 INCREMENT

This mode is achieved by initializing the U/D pin to a

high state (VIH) prior to achieving a low state (VIL) on the

CS pin. Subsequent rising edges of the U/D pin

increment the wiper setting toward terminal A. This is

shown in Figure 5-1.

After the wiper is incremented to the desired position,

the CS pin should be forced to VIH to ensure that

“unexpected” transitions on the U/D pin do not cause

the wiper setting to increment. Driving the CS pin to VIH

should occur as soon as possible (within device

specifications) after the last desired increment occurs.

When the device voltage falls below the RAM retention

voltage of the device, the wiper state may be corrupted.

When the device returns to the operating range, the

wiper will be loaded with the default POR wiper setting.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-1: Increment.

Note: The wiper value will not overflow. That is,

once the wiper value equals 0x3F,

subsequent increment commands are

ignored.

U/D

Wiper

1 2 3 4

X+1

XX+2 X+3 X+4

VIH

VIL

MCP4011/2/3/4

5.2.2 INCREMENT (FOR MCP402X

COMPATIBILITY)

This mode is achieved by initializing the U/D pin to a

high state (VIH) prior to achieving a low state (VIL) on the

CS pin. Subsequent rising edges of the U/D pin

increments the wiper setting toward terminal A. This is

shown in Figure 5-2.

After the wiper is incremented to the desired position,

the U/D pin should be driven low (VIL), and the CS pin

should be forced to VIH to ensure that “unexpected”

transitions on the U/D pin do not cause the wiper

setting to increment. Driving the CS pin to VIH should

occur as soon as possible (within device specifications)

after the last desired increment occurs.

When the device voltage falls below the RAM retention

voltage of the device, the wiper state may be corrupted.

When the device returns to the operating range, the

wiper will be loaded with the Default POR wiper setting.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-2: Increment (For MCP402X Compatibility).

Note: This command allows compatibility with

the MCP402X family, which supports

updating of the non-volatile wiper setting.

Note: The wiper value will not overflow. That is,

once the wiper value equals 0x3F,

subsequent increment commands are

ignored.

U/D

Wiper

1 2 3 4

X+1

XX+2 X+3 X+4

VIH

VIL

MCP4011/2/3/4

5.2.3 DECREMENT

This mode is achieved by initializing the U/D pin to a low

state (VIL) prior to achieving a low state (VIL) on the CS

pin. Subsequent rising edges of the U/D pin will

decrement the wiper setting toward terminal B. This is

shown in Figure 5-3.

After the wiper is decremented to the desired position,

the U/D pin should be forced low (VIL) and the CS pin

should be forced to VIH. This will ensure that

“unexpected” transitions on the U/D pin do not cause

the wiper setting to decrement. Driving the CS pin to

VIH should occur as soon as possible (within device

specifications) after the last desired increment occurs.

When the device voltage falls below the RAM retention

voltage of the device, the wiper state may be corrupted.

When the device returns to the operating range, the

wiper will be loaded with the default POR wiper setting.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-3: Decrement.

Note: The wiper value will not underflow. That is,

once the wiper value equals 0x00,

subsequent decrement commands are

ignored.

U/D

Wiper

1 2 3 4

X-1XX-2X-3X-4

VIH

VIH 56

VIL

MCP4011/2/3/4

5.2.4 DECREMENT (FOR MCP402X

COMPATIBILITY)

This mode is achieved by initializing the U/D pin to a

low state (VIL) prior to achieving a low state (VIL) on the

CS pin. Subsequent rising edges of the U/D pin

decrement the wiper setting toward terminal B. This is

shown in Figure 5-4.

After the wiper is decremented to the desired position,

the U/D pin should remain high (VIH), and the CS pin

should be forced to VIH to ensure that “unexpected”

transitions on the U/D pin do not cause the wiper

setting to increment. Driving the CS pin to VIH should

occur as soon as possible (within device specifications)

after the last desired increment occurs.

When the device voltage falls below the RAM retention

voltage of the device, the wiper state may be corrupted.

When the device returns to the operating range, the

wiper will be loaded with the default POR wiper setting.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-4: Decrement (For MCP402X Compatibility).

Note: This command allows compatibility with

the MCP402X family, which supports

updating of the non-volatile wiper setting.

Note: The wiper value will not underflow. That is,

once the wiper value equals 0x00,

subsequent decrement commands are

ignored.

U/D

Wiper X-1

XX-2 X-3 X-4

1 2 3 4

VIH

VIL

MCP4011/2/3/4

5.2.5 HIGH-VOLTAGE INCREMENT 1

(FOR MCP402X COMPATIBILITY)

This mode is achieved by initializing the U/D pin to a

high state (VIH) prior to the CS pin being driven to VIHH.

Subsequent rising edges of the U/D pin increment the

wiper setting toward terminal A. Set the U/D pin to the

high state (VIH) prior to forcing the CS pin to VIH. This

is shown in Figure 5-5.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-5: High-Voltage Increment 1 (For MCP402X Compatibility).

Note: This command allows compatibility with

the MCP402X family, which supports

updating of the non-volatile wiper setting

with the WiperLock Technology feature.

Note: The wiper value will not overflow. That is,

once the wiper value equals 0x3F,

subsequent increment commands are

ignored.

U/D

Wiper

1 2 3 4

X+1

XX+2 X+3 X+4

VIHH

VIH

VIL

VIH

MCP4011/2/3/4

5.2.6 HIGH-VOLTAGE INCREMENT 2

(FOR MCP402X COMPATIBILITY)

This mode is achieved by initializing the U/D pin to a

high state (VIH) prior to the CS pin being driven to VIHH.

Subsequent rising edges of the U/D pin increment the

wiper setting toward terminal A. Set the U/D pin to the

low state (VIL) prior to forcing the CS pin to VIH. This is

shown in Figure 5-6.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-6: High-Voltage Increment 2 (For MCP402X Compatibility).

Note: This command allows compatibility with

the MCP402X family, which supports

updating of the non-volatile wiper setting

with the WiperLock Technology feature.

Note: The wiper value will not overflow. That is,

once the wiper value equals 0x3F,

subsequent increment commands are

ignored.

U/D

Wiper

1 2 3 4

X+1

XX+2 X+3 X+4

VIHH

VIH

VIL

VIH

VIL

MCP4011/2/3/4

5.2.7 HIGH-VOLTAGE DECREMENT 1

(FOR MCP402X COMPATIBILITY)

This mode is achieved by initializing the U/D pin to a

low state (VIL) prior to the CS pin being driven to VIHH.

Subsequent rising edges of the U/D pin decrement the

wiper setting toward terminal B. Set the U/D pin to the

low state (VIL) prior to forcing the CS pin to VIH. This is

shown in Figure 5-7.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-7: High-Voltage Decrement 1 (For MCP402X Compatibility).

Note: This command allows compatibility with

the MCP402X family, which supports

updating of the non-volatile wiper setting

with the WiperLock Technology feature.

Note: The wiper value will not underflow. That is,

once the wiper value equals 0x00,

subsequent decrement commands are

ignored.

U/D

Wiper

1 2 3 4

X-1

XX-2 X-3 X-4

VIHH

VIH

VIL

VIH

VIL

MCP4011/2/3/4

5.2.8 HIGH-VOLTAGE DECREMENT 2

(FOR MCP402X COMPATIBILITY)

This mode is achieved by initializing the U/D pin to the

low state (VIL) prior to driving the CS pin to VIHH.

Subsequent rising edges of the U/D pin decrement the

wiper setting toward terminal B. Set the U/D pin to a

high state (VIH) prior to forcing the CS pin to VIH. This

is shown in Figure 5-8.

After the CS pin is driven to VIH (from VIL), any other

serial command may immediately be entered.

FIGURE 5-8: High-Voltage Decrement 2 (For MCP402X Compatibility).

Note: This command allows compatibility with

the MCP402X family, which supports

updating of the non-volatile wiper setting

with the WiperLock Technology feature.

Note: The wiper value will not underflow. That is,

once the wiper value equals 0x00,

subsequent decrement commands are

ignored.

U/D

Wiper

1 2 3 4

X-1

XX-2 X-3 X-4

VIHH

VDD

VIH

VIL

MCP4011/2/3/4

5.3 CS High Voltage

The CS pin is High-Voltage (VIHH) tolerant, like the

MCP402X. This allows the MCP401X to be used in

MCP402X applications without needing to change

other portions of the application circuit.

6.0 RESISTOR

Digital potentiometer applications can be divided into

two categories:

• Rheostat configuration

• Potentiometer (or voltage divider) configuration

Figure 6-1 shows a block diagram for the MCP401X

resistors.

FIGURE 6-1: Resistor Block Diagram.

Step resistance (RS) is the resistance from one tap

setting to the next. This value will be dependent on the

RAB value that has been selected. Table 6-1 shows the

typical step resistances for each device.

The total resistance of the device has minimal variation

due to operating voltage (see Figure 2-11, Figure 2-24,

Figure 2-36 or Figure 2-48).

TABLE 6-1: TYPICAL STEP RESISTANCES

Terminal A and B, as well as the wiper W, do not have

a polarity. These terminals can support both positive

and negative current.

N = 63

N = 62

N = 61

N = 1

N = 0

RW (1)

01h

Analog

Mux

RW (1)

00h

RW (1)

3Dh

RW (1)

3Eh

RW (1)

3Fh

Note 1: The wiper resistance is tap dependent.

That is, each tap selection resistance

has a small variation. This variation

effects the smaller resistance devices

(2.1 kΩ) more.

Part Number

Typical Resistance (Ω)

Total (RAB) Step (RS)

MCP401X-203E 2100 33.33

MCP401X-503E 5000 79.37

MCP401X-104E 10000 158.73

MCP401X-504E 50000 793.65

MCP4011/2/3/4

6.1 Resistor Configurations

6.1.1 RHEOSTAT CONFIGURATION

When used as a rheostat, two of the three digital poten-

tiometer’s terminals are used as a resistive element in

the circuit. With terminal W (wiper) and either terminal

A or terminal B, a variable resistor is created. The

resistance will depend on the tap setting of the wiper

and the wiper’s resistance. The resistance is controlled

by changing the wiper setting.

The unused terminal (B or A) should be left floating.

Figure 6-2 shows the two possible resistors that can be

used. Reversing the polarity of the A and B terminals

will not affect operation.

FIGURE 6-2: Rheostat Configuration.

This allows the control of the total resistance between

the two nodes. The total resistance depends on the

“starting” terminal to the wiper terminal. At the code

00h, the RBW resistance is minimal (RW), but the RAW

resistance in maximized (RAB + RW). Conversely, at the

code 3Fh, the RAW resistance is minimal (RW), but the

RBW resistance in maximized (RAB + RW).

The resistance step size (RS) equates to one LSb of the

resistor.

The change in wiper-to-end terminal resistance over

temperature is shown in Figure 2-11, Figure 2-24,

Figure 2-36 and Figure 2-48. The most variation over

temperature will occur in the first few codes due to the

wiper resistance coefficient affecting the total

resistance. The remaining codes are dominated by the

total resistance tempco RAB.

6.1.2 POTENTIOMETER

CONFIGURATION

When used as a potentiometer, all three terminals are

tied to different nodes in the circuit. This allows the

potentiometer to output a voltage proportional to the

input voltage. This configuration is sometimes called

voltage divider mode. The potentiometer is used to

provide a variable voltage by adjusting the wiper

position between the two endpoints as shown in

Figure 6-3. Reversing the polarity of the A and B

terminals will not affect operation.

FIGURE 6-3: Potentiometer Configuration.

The temperature coefficient of the RAB resistors is

minimal by design. In this configuration, the resistors all

change uniformly, so minimal variation should be seen.

The wiper resistor temperature coefficient is different

from the RAB temperature coefficient. The voltage at

node V3 (Figure 6-3) is not dependent on this wiper

resistance, just the ratio of the RAB resistors, so this

temperature coefficient in most cases can be

ignored.

Note: To avoid damage to the internal wiper

circuitry in this configuration, care should

be taken to insure the current flow never

exceeds 2.5 mA.

Resistor

RAW RBW

Note: To avoid damage to the internal wiper

circuitry in this configuration, care should

be taken to insure the current flow never

exceeds 2.5 mA.

MCP4011/2/3/4

6.2 Wiper Resistance

Wiper resistance is the series resistance of the wiper.

This resistance is typically measured when the wiper is

positioned at either zero-scale (00h) or full-scale (3Fh).

The wiper resistance in potentiometer-generated

voltage divider applications is not a significant source

of error.

The wiper resistance in rheostat applications can

create significant non-linearity as the wiper is moved

toward zero-scale (00h). The lower the nominal

resistance, the greater the possible error.

Wiper resistance is significant depending on the

devices operating voltage. As the device voltage

decreases, the wiper resistance increases (see

Figure 6-4 and Ta b l e 6 - 2 ).

In a rheostat configuration, this change in voltage

needs to be taken into account, particularly for the

lower resistance devices. For the 2.1 kΩ device, the

maximum wiper resistance at 5.5V is approximately 6%

of the total resistance, while at 2.7V, it is approximately

15.5% of the total resistance.

In a potentiometer configuration, the wiper resistance

variation does not effect the output voltage seen on the

terminal W pin.

The slope of the resistance has a linear area (at the

higher voltages) and a non-linear area (at the lower

voltages), where resistance increases faster than the

voltage drop (at low voltages).

FIGURE 6-4: Relationship of Wiper

Resistance (RW) to Voltage.

Since there is minimal variation of the total device

resistance over voltage, at a constant temperature (see

Figure 2-11, Figure 2-24, Figure 2-36 or Figure 2-48),

the change in wiper resistance over voltage can have a

significant impact on the INL and DNL error.

TABLE 6-2: TYPICAL STEP RESISTANCES AND RELATIONSHIP TO WIPER RESISTANCE

VDD

Note: The slope of the resistance has a linear

area (at the higher voltages) and a non-

linear area (at the lower voltages).

Resistance (Ω)R

W / RS (%) (1, 2) R

W / RAB (%) (1, 3)

Typical Wiper (RW)

RW =

Typical

RW = Max

@ 5.5V

RW = Max

@ 2.7V

RW =

Typical

RW = Max

@ 5.5V

RW = Max

@ 2.7V

Total

(RAB)

Step

(RS)Typical Max @

5.5V

Max @

2.7V

2100 33.33 75 125 325 225.0% 375.0% 975.0% 3.57% 5.95% 15.48%

5000 79.37 75 125 325 94.5% 157.5% 409.5% 1.5% 2.50% 6.50%

10000 158.73 75 125 325 47.25% 78.75% 204.75% 0.75% 1.25% 3.25%

50000 793.65 75 125 325 9.45% 15.75% 40.95% 0.15% 0.25% 0.65%

Note 1: The wiper resistance (RW) is not a significant source of error in potentiometer-generated voltage divider

applications. In rheostat applications, the variation of the RW value can create significant non-linearity.

2: RS is the typical value. The variation of this resistance is minimal over voltage.

3: RAB is the typical value. The variation of this resistance is minimal over voltage.

MCP4011/2/3/4

6.3 Operational Characteristics

Understanding the operational characteristics of the

device’s resistor components is important to the system

design.

6.3.1 ACCURACY

6.3.1.1 Integral Non-Linearity (INL)

INL error for these devices is the maximum deviation

between an actual code transition point and its

corresponding ideal transition point after offset and

gain errors have been removed. These endpoints are

from 0x00 to 0x3F. Refer to Figure 6-5.

Positive INL means higher resistance than ideal.

Negative INL means lower resistance than ideal.

FIGURE 6-5: INL Accuracy.

6.3.1.2 Differential Non-Linearity (DNL)

DNL error is the measure of variations in code widths

from the ideal code width. A DNL error of zero would

imply that every code is exactly 1 LSb wide.

FIGURE 6-6: DNL Accuracy.

6.3.1.3 Ratiometric Temperature Coefficient

The ratiometric temperature coefficient quantifies the

error in the ratio RAW/RWB due to temperature drift.

This is typically the critical error when using a

potentiometer device (MCP4011 and MCP4013) in a

voltage divider configuration.

6.3.1.4 Absolute Temperature Coefficient

The absolute temperature coefficient quantifies the

error in the end-to-end resistance (nominal resistance

RAB) due to temperature drift. This is typically the

critical error when using a rheostat device (MCP4012

and MCP4014) in an adjustable resistor configuration.

111

110

101

100

011

010

001

000

Digital

Input

Code

Actual

Rransfer

Function

INL < 0

Ideal Transfer

Function

INL < 0

Digital Pot Output

111

110

101

100

011

010

001

000

Digital

Input

Code

Actual

Transfer

Function

Ideal Transfer

Function

Narrow Code < 1 LSb

Wide Code, > 1 LSb

Digital Pot Output

MCP4011/2/3/4

6.3.2 MONOTONIC OPERATION

Monotonic operation means that the device’s

resistance increases with every step change (from

terminal A to terminal B or terminal B to terminal A).

The wiper resistance is different at each tap location.

When changing from one tap position to the next (either

increasing or decreasing), the ΔRW is less than the

ΔRS. When this change occurs, the device voltage and

temperature are “the same” for the two tap positions.

FIGURE 6-7: Resistance RBW.

0x3F

0x3E

0x3D

0x03

0x02

0x01

0x00

Digital Input Code

Resistance (RBW)

(@ tap)

RS0

RS1

RS3

RS62

RS63

RBW = RSn + RW(@ Tap n)

n = 0

n = ?

MCP4011/2/3/4

7.0 DESIGN CONSIDERATIONS

In the design of a system with the MCP401X devices,

the following considerations should be taken into

account:

• The Power Supply

• The Layout

7.1 Power Supply Considerations

The typical application will require a bypass capacitor

in order to filter high-frequency noise, which can be

induced onto the power supply's traces. The bypass

capacitor helps to minimize the effect of these noise

sources on signal integrity. Figure 7-1 illustrates an

appropriate bypass strategy.

In this example, the recommended bypass capacitor

value is 0.1 µF. This capacitor should be placed as

close (within 4 mm) to the device power pin (VDD) as

possible.

The power source supplying these devices should be

as clean as possible. If the application circuit has

separate digital and analog power supplies, VDD and

VSS should reside on the analog plane.

FIGURE 7-1: Typical Microcontroller

Connections.

7.2 Layout Considerations

Inductively-coupled AC transients and digital switching

noise can degrade the input and output signal integrity,

potentially masking the MCP4011/2/3/4’s performance.

Careful board layout will minimize these effects and

increase the Signal-to-Noise Ratio (SNR). Bench

testing has shown that a multi-layer board utilizing a

low-inductance ground plane, isolated inputs, isolated

outputs and proper decoupling are critical to achieving

the performance that the silicon is capable of providing.

Particularly harsh environments may require shielding

of critical signals.

If low noise is desired, breadboards and wire-wrapped

boards are not recommended.

VDD

VSS VSS

MCP4011/2/3/4

0.1 µF

PIC® Microcontroller

0.1 µF

U/D

MCP4011/2/3/4

8.0 APPLICATIONS EXAMPLES

Non-volatile digital potentiometers have a multitude of

practical uses in modern electronic circuits. The most

popular uses include precision calibration of set point

thresholds, sensor trimming, LCD bias trimming, audio

attenuation, adjustable power supplies, motor control

overcurrent trip setting, adjustable gain amplifiers and

offset trimming. The MCP4011/2/3/4 devices can be

used to replace the common mechanical trim pot in

applications where the operating and terminal voltages

are within CMOS process limitations (VDD = 2.7V to

5.5V).

8.1 Set Point Threshold Trimming

Applications that need accurate detection of an input

threshold event often need several sources of error

eliminated. Use of comparators and operational

amplifiers (op amps) with low offset and gain error can

help achieve the desired accuracy, but in many

applications, the input source variation is beyond the

designer’s control. If the entire system can be

calibrated after assembly in a controlled environment

(like factory test), these sources of error are minimized,

if not entirely eliminated.

Figure 8-1 illustrates a common digital potentiometer

configuration. This configuration is often referred to as

a “windowed voltage divider”. Note that R1 and R2 are

not necessary to create the voltage divider, but their

presence is useful when the desired threshold has

limited range. It is “windowed” because R1 and R2 can

narrow the adjustable range of VTRIP to a value much

less than VDD – VSS. If the output range is reduced, the

magnitude of each output step is reduced. This

effectively increases the trimming resolution for a fixed

digital potentiometer resolution. This technique may

allow a lower-cost digital potentiometer to be utilized

(64 steps instead of 256 steps).

The MCP4011’s and MCP4013’s low DNL performance

is critical to meeting calibration accuracy in production

without having to use a higher precision digital

potentiometer.

EQUATION 8-1: CALCULATING THE

WIPER SETTING FROM

THE DESIRED VTRIP

FIGURE 8-1: Using the Digital

Potentiometer to Set a Precise Output Voltage.

8.1.1 TRIMMING A THRESHOLD FOR AN

OPTICAL SENSOR

If the application has to calibrate the threshold of a

diode, transistor or resistor, a variation range of 0.1V is

common. Often, the desired resolution of 2 mV or

better is adequate to accurately detect the presence of

a precise signal. A “windowed” voltage divider, utilizing

the MCP4011 or MCP4013, would be a potential

solution as shown in Figure 8-2.

FIGURE 8-2: Set Point or Threshold

Calibration.

VTRIP VDD

R2RWB

R1RAB R2

-----------------------------------

⎝⎠

⎛⎞

RAB RNominal

RWB RAB

------

⎝⎠

⎛⎞

•=

DVTRIP

VDD

--------------

⎝⎠

⎛⎞

R1RAB R2

++()R2

–()•

⎝⎠

⎛⎞

63•=

Where:

D = Digital Potentiometer Wiper Setting (0-63)

VDD

VOUT

MCP4011

U/D

VTRIP

0.1 µF

Comparator

VCC+

VCC–

VDD

Rsense

VDD

MCP4011

U/D MCP6021

MCP4011/2/3/4

8.2 Operational Amplifier

Applications

Figure 8-3, Figure 8-4 and Figure 8-5 illustrate typical

amplifier circuits that could replace fixed resistors with

the MCP4011/2/3/4 to achieve digitally-adjustable

analog solutions.

Figure 8-4 shows a circuit that allows a non-inverting

amplifier to have its’ offset and gain to be independently

trimmed. The MCP4011 is used along with resistors R1

and R2 to set the offset voltage. The sum of R1 + R2

resistance should be significantly greater (> 100 times)

the resistance value of the MCP4011. This allows each

increment or decrement in the MCP4011 to be a fine

adjustment of the offset voltage. The input voltage of

the op amp (VIN) should be centered at the op amps Vw

voltage. The gain is adjusted by the MCP4012. If the

resistance value of the MCP4012 is small compared to

the resistance value of R3, then this is a fine adjustment

of the gain. If the resistance value of the MCP4012 is

equal (or large) compared to the resistance value of R3,

then this is a course adjustment of the gain. In general,

trim the course adjustments first and then trim the fine

adjustments.

FIGURE 8-3: Trimming Offset and Gain in

an Inverting Amplifier.

FIGURE 8-4: Trimming Offset and Gain in

a Non-Inverting Amplifier.

FIGURE 8-5: Programmable Filter.

Op Amp

VIN

VOUT

–

MCP4011

VDD

R3R4

MCP4011

MCP6001

Op Amp

VIN

VOUT

–

VDD

MCP6291

MCP4011

MCP4012

VDD

Op Amp

VIN VOUT

–

MCP4011

VDD

MCP4011

R3R4

REq C

⋅⋅

-----------------------------=

Pot1

Pot2

REq R1RAB RWB

–+()R2RWB

+()Rw

Thevenin

Equivalent

MCP6021

MCP4011/2/3/4

8.3 Temperature Sensor Applications

Thermistors are resistors with very predictable

variation with temperature. Thermistors are a popular

sensor choice when a low-cost, temperature-sensing

solution is desired. Unfortunately, thermistors have

non-linear characteristics that are undesirable, typically

requiring trimming in an application to achieve greater

accuracy. There are several common solutions to trim

and linearize thermistors. Figure 8-6 and Figure 8-7

are simple methods for linearizing a 3-terminal NTC

thermistor. Both are simple voltage dividers using a

Positive Temperature Coefficient (PTC) resistor (R1)

with a transfer function capable of compensating for the

linearity error in the Negative Temperature Coefficient

(NTC) thermistor.

The circuit, illustrated by Figure 8-6, utilizes a digital

rheostat for trimming the offset error caused by the

thermistor’s part-to-part variation. This solution puts the

digital potentiometer’s RW into the voltage divider

calculation. The MCP4011/2/3/4’s RAB temperature

coefficient is 50 ppm (-20°C to +70°C). RW’s error is

substantially greater than RAB’s error because RW

varies with VDD, wiper setting and temperature. For the

50 kΩ devices, the error introduced by RW is, in most

cases, insignificant as long as the wiper setting is > 6.

For the 2 kΩ devices, the error introduced by RW is

significant because it is a higher percentage of RWB.

For these reasons, the circuit illustrated in Figure 8-6 is

not the most optimum method for “exciting” and

linearizing a thermistor.

FIGURE 8-6: Thermistor Calibration using

a Digital Potentiometer in a Rheostat

Configuration.

The circuit illustrated by Figure 8-7 utilizes a digital

potentiometer for trimming the offset error. This

solution removes RW from the trimming equation along

with the error associated with RW. R2 is not required,

but can be utilized to reduce the trimming “window” and

reduce variation due to the digital potentiometer’s RAB

part-to-part variability.

FIGURE 8-7: Thermistor Calibration using

a Digital Potentiometer in a Potentiometer

Configuration.

8.4 Wheatstone Bridge Trimming

Another common configuration to “excite” a sensor

(such as a strain gauge, pressure sensor or thermistor)

is the wheatstone bridge configuration. The wheat-

stone bridge provides a differential output instead of a

single-ended output. Figure 8-8 illustrates a

wheatstone bridge utilizing one to three digital

potentiometers. The digital potentiometers in this

example are used to trim the offset and gain of the

wheatstone bridge.

FIGURE 8-8: Wheatstone Bridge

Trimming.

NTC

VDD

MCP4012

VOUT

Thermistor

NTC

VDD

MCP4011

VOUT

Thermistor

VDD

MCP4012

VOUT

2.1 kΩ

MCP4012

50 kΩ

MCP4012

50 kΩ

MCP4011/2/3/4

9.0 DEVELOPMENT SUPPORT

9.1 Evaluation/Demonstration Boards

Currently there are three boards that are available that

can be used to evaluate the MCP401X family of

devices.

1. The MCP402X Digital Potentiometer Evaluation

Board kit (MCP402XEV) contains a simple dem-

onstration board utilizing a PIC10F206, the

MCP401X and a blank PCB, which can be pop-

ulated with any desired MCP4011/2/3/4 device

in a SOT-23-5, SOT-23-6 or 150 mil SOIC 8-pin

package.

This board has two push buttons to control when

the PIC® microcontroller generates MCP402X

serial commands. The example firmware

demonstrates the following commands:

• Increment

• Decrement

• High-Voltage Increment and Enable

WiperLock Technology

• High-Voltage Decrement and Enable

WiperLock Technology

• High-Voltage Increment and Disable

WiperLock Technology

• High-Voltage Decrement and Disable

WiperLock Technology

The populated board (with the MCP4011) can

be used to evaluate the other MCP401X devices

by appropriately jumpering the PCB pads.

2. The SOT-23-5/6 Evaluation Board (VSUPEV2)

can be used to evaluate the characteristics of

the MCP4012, MCP4013 and MCP4014

devices.

3. The 8-pin SOIC/MSOP/TSSOP/DIP Evaluation

Board (SOIC8EV) can be used to evaluate the

characteristics of the MCP4011 device in either

the SOIC or MSOP package.

4. The MCP4XXX Digital Potentiometer Daughter

Board allows the system designer to quickly

evaluate the operation of Microchip Technol-

ogy's MCP42XXX and MCP402X Digital Poten-

tiometers. The board supports two MCP42XXX

devices and an MCP402X device, which can be

replaced with an MCP401X device.

The board also has a voltage doubler device

(TC1240A), which can be used to show the

WiperLock™ Technology feature of the

MCP4021.

These boards may be purchased directly from the

Microchip web site at www.microchip.com.

MCP4011/2/3/4

10.0 PACKAGING INFORMATION

10.1 Package Marking Information

5-Lead SOT-23 (MCP4014)Example:

XXNN JU25

Part Number Code

MCP4014T-202E/OT JUNN

MCP4014T-502E/OT JVNN

MCP4014T-103E/OT JWNN

MCP4014T-503E/OT JXNN

Note: Applies to 5-Lead SOT-23

6-Lead SOT-23 (MCP4012 / MCP4013)Example:

XXNN BJ25

Part Number

Code

MCP4012 MCP4013

MCP401xT-202E/CH BJNN BPNN

MCP401xT-502E/CH BKNN BQNN

MCP401xT-103E/CH BLNN BRNN

MCP401xT-503E/CH BMNN BSNN

Note: Applies to 6-Lead SOT-23

Legend: XX...X Customer-specific information

Y Year code (last digit of calendar year)

YY Year code (last 2 digits of calendar year)

WW Week code (week of January 1 is week ‘01’)

NNN Alphanumeric traceability code

Pb-free JEDEC designator for Matte Tin (Sn)

*This package is Pb-free. The Pb-free JEDEC designator ( )

can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will

be carried over to the next line, thus limiting the number of available

characters for customer-specific information.

MCP4011/2/3/4

Package Marking Information

Legend: XX...X Customer-specific information

Y Year code (last digit of calendar year)

YY Year code (last 2 digits of calendar year)

WW Week code (week of January 1 is week ‘01’)

NNN Alphanumeric traceability code

Pb-free JEDEC designator for Matte Tin (Sn)

*This package is Pb-free. The Pb-free JEDEC designator ( )

can be found on the outer packaging for this package.

Note: In the event the full Microchip part number cannot be marked on one line, it will

be carried over to the next line, thus limiting the number of available

characters for customer-specific information.

8-Lead MSOP (MCP4011) Example:

XXXXXX

YWWNNN

401122

534256

Example:8-Lead DFN (2x3) (MCP4011)

XXX

YWW

NNN

ABE

534

256

8-Lead SOIC (150 mil) (MCP4011) Example:

XXXXXXXX

XXXXYYWW

NNN

401152E

SN^^ 0534

256

Part Number Code

MCP4011T-202E/MC ABE

MCP4011T-502E/MC ABF

MCP4011T-103E/MC ABG

MCP4011T-503E/MC ABH

Note: Applies to 8-Lead DFN

Part Numbers

Code

8L-MSOP 8L-SOIC

MCP4011-202E/MS MCP4011-202E/SN 22

MCP4011-502E/MS MCP4011-502E/SN 52

MCP4011-103E/MS MCP4011-103E/SN 13

MCP4011-503E/MS MCP4011-503E/SN 53

MCP4011/2/3/4

5-Lead Plastic Small Outline Transistor (OT) (SOT-23)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

10501050

Mold Draft Angle Bottom

10501050

Mold Draft Angle Top

0.500.430.35.020.017.014BLead Width

0.200.150.09.008.006.004

Lead Thickness

10501050

Foot Angle

0.550.450.35.022.018.014LFoot Length

3.102.952.80.122.116.110DOverall Length

1.751.631.50.069.064.059E1Molded Package Width

3.002.802.60.118.110.102EOverall Width

0.150.080.00.006.003.000A1Standoff

1.301.100.90.051.043.035A2Molded Package Thickness

1.451.180.90.057.046.035AOverall Height

1.90.075

Outside lead pitch (basic)

0.95.038

Pitch

Number of Pins

MAXNOMMINMAXNOMMINDimension Limits

MILLIMETERSINCHES

Units

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side.

Notes:

EIAJ Equivalent: SC-74A

Drawing No. C04-091

Controlling Parameter

Revised 09-12-05

MCP4011/2/3/4

6-Lead Plastic Small Outline Transistor (CH) (SOT-23)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

10501050

Mold Draft Angle Bottom

10501050

Mold Draft Angle Top

0.500.430.35.020.017.014BLead Width

0.200.150.09.008.006.004

Lead Thickness

10501050

Foot Angle

0.550.450.35.022.018.014LFoot Length

3.102.952.80.122.116.110DOverall Length

1.751.631.50.069.064.059E1Molded Package Width

3.002.802.60.118.110.102EOverall Width

0.150.080.00.006.003.000A1Standoff

1.301.100.90.051.043.035A2Molded Package Thickness

1.451.180.90.057.046.035AOverall Height

1.90 BSC.075 BSC

Outside lead pitch

0.95 BSC.038 BSC

Pitch

Number of Pins

MAXNOMMINMAXNOMMINDimension Limits

MILLIMETERSINCHES

Units

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .005" (0.127mm) per side.

Notes:

JEITA (formerly EIAJ) equivalent: SC-74A

Controlling Parameter

Drawing No. C04-120

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

See ASME Y14.5M

Revised 09-12-05

MCP4011/2/3/4

8-Lead Plastic Dual-Flat No-Lead Package (MC) 2x3x0.9 mm Body (DFN) – Saw Singulated

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Number of Pins

Pitch

Overall Height

Standoff

Contact Thickness

Overall Length

Overall Width

Exposed Pad Length

Exposed Pad Width

Contact Width

Contact Length §

Contact-to-Exposed Pad §

Units

Dimension Limits

0.80

0.00

1.30

1.50

0.18

0.30

0.20

0.50 BSC

0.90

0.02

0.20 REF

2.00 BSC

3.00 BSC

—

0.25

0.40

—

1.00

0.05

1.75

1.90

0.30

0.50

—

MIN NOM MAX

MILLIMETERS

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Package may have one or more exposed tie bars at ends.

3. § Significant Characteristic

4. Package is saw singulated

5. Dimensioning and tolerancing per ASME Y14.5M

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Microchip Technology Drawing No. C04–123, Sept. 8, 2006

A3 A1 NOTE 2

NOTE 1

BOTTOM VIEW

EXPOSED PAD

TOP VIEW

MCP4011/2/3/4

8-Lead Plastic Micro Small Outline Package (MS) (MSOP)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

NOTE 1

Number of Pins

Pitch

Overall Height

Molded Package Thickness

Standoff

Overall Width

Molded Package Width

Overall Length

Foot Length

Footprint

Foot Angle

Lead Thickness

Lead Width

Units

Dimension Limits

—

0.75

0.00

0.40

0°

0.08

0.22

0.65 BSC

—

0.85

—

4.90 BSC

3.00 BSC

0.60

0.95 REF

—

1.10

0.95

0.15

0.80

8°

0.23

0.40

MIN NOM MAX

MILLIMETERS

Notes:

1. Pin 1 visual index feature may vary, but must be located within the hatched area.

2. Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions

shall not exceed 0.15 mm per side.

3. Dimensioning and tolerancing per ASME Y14.5M

BSC: Basic Dimension. Theoretically exact value shown without tolerances.

REF: Reference Dimension, usually without tolerance, for information purposes only.

Microchip Technology Drawing No. C04–111, Sept. 8, 2006

MCP4011/2/3/4

8-Lead Plastic Small Outline (SN) – Narrow, 150 mil (SOIC)

Note: For the most current package drawings, please see the Microchip Packaging Specification located at

http://www.microchip.com/packaging

Foot Angle φ048048

1512015120

Mold Draft Angle Bottom

1512015120

Mold Draft Angle Top

0.510.420.33.020.017.013BLead Width

0.250.230.20.010.009.008

Lead Thickness

0.760.620.48.030.025.019LFoot Length

0.510.380.25.020.015.010hChamfer Distance

5.004.904.80.197.193.189DOverall Length

3.993.913.71.157.154.146E1Molded Package Width

6.206.025.79.244.237.228EOverall Width

0.250.180.10.010.007.004A1Standoff §

1.551.421.32.061.056.052A2Molded Package Thickness

1.751.551.35.069.061.053AOverall Height

1.27

.050

Pitch

Number of Pins

MAXNOMMINMAXNOMMINDimension Limits

MILLIMETERSINCHES*Units

45°

* Controlling Parameter

Notes:

Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010” (0.254mm) per side.

JEDEC Equivalent: MS-012

Drawing No. C04-057

§ Significant Characteristic

MCP4011/2/3/4

APPENDIX A: REVISION HISTORY

Revision C (December 2006)

• Added device designators in conditions column to

associate units (MHz) in Bandwidth -3 dB

parameter in AC/DC Characteristics table.

• Added device designations in conditions column

for R-INL and R-DNL specifications.

Revision B (October 2006)

• For the 10 kΩ device, the rheostat differential

non-linearity specification at 2.7V was changed

from ±0.5 LSb to ±1 LSb.

• Figure 2-9 in Section 2.0 “Typical Performance

Curves” was updated with the correct data.

• Added Figure 2-55 for -3 db Bandwidth

information.

• Added Figure 2-56 for -3 db Bandwidth test

circuit.

• Updated available Development Tools

• Added disclaimer to package outline drawings

and updated changed drawings as needed.

Revision A (November 2005)

• Original Release of this Document.

MCP4011/2/3/4

NOTES:

MCP4011/2/3/4

PRODUCT IDENTIFICATION SYSTEM

To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.

Device: MCP4011: Single Potentiometer with U/D Interface

MCP4011T: Single Potentiometer with U/D Interface

(Tape and Reel) (SOIC, MSOP)

MCP4012: Single Rheostat with U/D interface

MCP4012T: Single Rheostat with U/D interface

(Tape and Reel) (SOT-23-6)

MCP4013: Single Potentiometer to GND with U/D

Interface

MCP4013T: Single Potentiometer to GND with U/D

Interface (Tape and Reel) (SOT-23-6)

MCP4014: Single Rheostat to GND with U/D

Interface

MCP4014T: Single Rheostat to GND with U/D

Interface (Tape and Reel)(SOT-23-5)

Resistance Version: 202 = 2.1 kΩ

502 = 5 kΩ

103 = 10 kΩ

503 = 50 kΩ

Temperature Range: E = -40°C to +125°C

Package: CH = Plastic Small Outline Transistor, 6-lead

MC = Plastic Dual Flat No Lead (2x3x0.9 mm), 8-lead

MS = Plastic MSOP, 8-lead

SN = Plastic SOIC, (150 mil Body), 8-lead

OT = Plastic Small Outline Transistor, 5-lead

PART NO. X/XX

PackageTemperature

Range

Device

Examples:

a) MCP4011-103E/MS: 10 kΩ, 8-LD MSOP

b) MCP4011-103E/SN: 10 kΩ, 8-LD SOIC

c) MCP4011T-103E/MC: T/R, 10 kΩ, 8-LD DFN

d) MCP4011T-103E/MS: T/R, 10 kΩ, 8-LD MSOP

e) MCP4011T-103E/SN: T/R, 10 kΩ, 8-LD SOIC

f) MCP4011-202E/MS: 2.1 kΩ, 8-LD MSOP

g) MCP4011-202E/SN: 2.1 kΩ, 8-LD SOIC

h) MCP4011T-202E/MC: T/R, 2.1 kΩ, 8-LD DFN

i) MCP4011T-202E/MS: T/R, 2.1 kΩ, 8-LD MSOP

j) MCP4011T-202E/SN: T/R, 2.1 kΩ, 8-LD SOIC

k) MCP4011-502E/MS: 5 kΩ, 8-LD MSOP

l) MCP4011-502E/SN: 5 kΩ, 8-LD SOIC

m) MCP4011T-502E/MC: T/R, 5 kΩ, 8-LD DFN

n) MCP4011T-502E/MS: T/R, 5 kΩ, 8-LD MSOP

o) MCP4011T-502E/SN: T/R, 5 kΩ, 8-LD SOIC

p) MCP4011-503E/MS: 50 kΩ, 8-LD MSOP

q) MCP4011-503E/SN: 50 kΩ, 8-LD SOIC

r) MCP4011T-503E/MC: T/R, 50 kΩ, 8-LD DFN

s) MCP4011T-503E/MS: T/R, 50 kΩ, 8-LD MSOP

t) MCP4011T-503E/SN: T/R, 50 kΩ, 8-LD SOIC

a) MCP4012T-202E/CH 2.1 kΩ, 6-LD SOT-23

b) MCP4012T-502E/CH 5 kΩ, 6-LD SOT-23

c) MCP4012T-103E/CH 10 kΩ, 6-LD SOT-23

d) MCP4012T-503E/CH 50 kΩ, 6-LD SOT-23

a) MCP4013T-202E/CH 2.1 kΩ, 6-LD SOT-23

b) MCP4013T-502E/CH 5 kΩ, 6-LD SOT-23

c) MCP4013T-103E/CH 10 kΩ, 6-LD SOT-23

d) MCP4013T-503E/CH 50 kΩ, 6-LD SOT-23

a) MCP4014T-202E/OT 2.1 kΩ, 5-LD SOT-23

b) MCP4014T-502E/OT 5 kΩ, 5-LD SOT-23

c) MCP4014T-103E/OT 10 kΩ, 5-LD SOT-23

d) MCP4014T-503E/OT 50 kΩ, 5-LD SOT-23

XXX

Resistance

Version

MCP4011/2/3/4

NOTES:

Information contained in this publication regarding device

applications and the like is provided only for your convenience

and may be superseded by updates. It is your responsibility to

ensure that your application meets with your specifications.

MICROCHIP MAKES NO REPRESENTATIONS OR

WARRANTIES OF ANY KIND WHETHER EXPRESS OR

IMPLIED, WRITTEN OR ORAL, STATUTORY OR

OTHERWISE, RELATED TO THE INFORMATION,

INCLUDING BUT NOT LIMITED TO ITS CONDITION,

QUALITY, PERFORMANCE, MERCHANTABILITY OR

FITNESS FOR PURPOSE. Microchip disclaims all liability

arising from this information and its use. Use of Microchip

devices in life support and/or safety applications is entirely at

the buyer’s risk, and the buyer agrees to defend, indemnify and

hold harmless Microchip from any and all damages, claims,

suits, or expenses resulting from such use. No licenses are

conveyed, implicitly or otherwise, under any Microchip

intellectual property rights.

Trademarks

The Microchip name and logo, the Microchip logo, Accuron,

dsPIC, KEELOQ, microID, MPLAB, PIC, PICmicro,

PICSTART, PRO MATE, PowerSmart, rfPIC, and

SmartShunt are registered trademarks of Microchip

Technology Incorporated in the U.S.A. and other countries.

AmpLab, FilterLab, Migratable Memory, MXDEV, MXLAB,

SEEVAL, SmartSensor and The Embedded Control Solutions

Company are registered trademarks of Microchip Technology

Incorporated in the U.S.A.

Analog-for-the-Digital Age, Application Maestro, CodeGuard,

dsPICDEM, dsPICDEM.net, dsPICworks, ECAN,

ECONOMONITOR, FanSense, FlexROM, fuzzyLAB,

In-Circuit Serial Programming, ICSP, ICEPIC, Linear Active

Thermistor, Mindi, MiWi, MPASM, MPLIB, MPLINK, PICkit,

PICDEM, PICDEM.net, PICLAB, PICtail, PowerCal,

PowerInfo, PowerMate, PowerTool, REAL ICE, rfLAB,

rfPICDEM, Select Mode, Smart Serial, SmartTel, Total

Endurance, UNI/O, WiperLock and ZENA are trademarks of

Microchip Technology Incorporated in the U.S.A. and other

countries.

SQTP is a service mark of Microchip Technology Incorporated

in the U.S.A.

All other trademarks mentioned herein are property of their

respective companies.

Printed on recycled paper.

Note the following details of the code protection feature on Microchip devices:

• Microchip products meet the specification contained in their particular Microchip Data Sheet.

• Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the

intended manner and under normal conditions.

• There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our

knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data

Sheets. Most likely, the person doing so is engaged in theft of intellectual property.

• Microchip is willing to work with the customer who is concerned about the integrity of their code.

• Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not

mean that we are guaranteeing the product as “unbreakable.”

Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our

products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts

allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.

Microchip received ISO/TS-16949:2002 certification for its worldwide

headquarters, design and wafer fabrication facilities in Chandler and

Tempe, Arizona, Gresham, Oregon and Mountain View, California. The

Company’s quality system processes and procedures are for its PIC®

8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs,

microperipherals, nonvolatile memory and analog products. In

addition, Microchip’s quality system for the design and manufacture of

development systems is ISO 9001:2000 certified.

AMERICAS

Corporate Office

2355 West Chandler Blvd.

Chandler, AZ 85224-6199

Tel: 480-792-7200

Fax: 480-792-7277

Technical Support:

http://support.microchip.com

Web Address:

www.microchip.com

Atlanta

Duluth, GA

Tel: 678-957-9614

Fax: 678-957-1455

Boston

Westborough, MA

Tel: 774-760-0087

Fax: 774-760-0088

Chicago

Itasca, IL

Tel: 630-285-0071

Fax: 630-285-0075

Dallas

Addison, TX

Tel: 972-818-7423

Fax: 972-818-2924

Detroit

Farmington Hills, MI

Tel: 248-538-2250

Fax: 248-538-2260

Kokomo

Kokomo, IN

Tel: 765-864-8360

Fax: 765-864-8387

Los Angeles

Mission Viejo, CA

Tel: 949-462-9523

Fax: 949-462-9608

Santa Clara

Santa Clara, CA

Tel: 408-961-6444

Fax: 408-961-6445

Toronto

Mississauga, Ontario,

Canada

Tel: 905-673-0699

Fax: 905-673-6509

ASIA/PACIFIC

Asia Pacific Office

Suites 3707-14, 37th Floor

Tower 6, The Gateway

Habour City, Kowloon

Hong Kong

Tel: 852-2401-1200

Fax: 852-2401-3431

Australia - Sydney

Tel: 61-2-9868-6733

Fax: 61-2-9868-6755

China - Beijing

Tel: 86-10-8528-2100

Fax: 86-10-8528-2104

China - Chengdu

Tel: 86-28-8665-5511

Fax: 86-28-8665-7889

China - Fuzhou

Tel: 86-591-8750-3506

Fax: 86-591-8750-3521

China - Hong Kong SAR

Tel: 852-2401-1200

Fax: 852-2401-3431

China - Qingdao

Tel: 86-532-8502-7355

Fax: 86-532-8502-7205

China - Shanghai

Tel: 86-21-5407-5533

Fax: 86-21-5407-5066

China - Shenyang

Tel: 86-24-2334-2829

Fax: 86-24-2334-2393

China - Shenzhen

Tel: 86-755-8203-2660

Fax: 86-755-8203-1760

China - Shunde

Tel: 86-757-2839-5507

Fax: 86-757-2839-5571

China - Wuhan

Tel: 86-27-5980-5300

Fax: 86-27-5980-5118

China - Xian

Tel: 86-29-8833-7250

Fax: 86-29-8833-7256

ASIA/PACIFIC

India - Bangalore

Tel: 91-80-4182-8400

Fax: 91-80-4182-8422

India - New Delhi

Tel: 91-11-4160-8631

Fax: 91-11-4160-8632

India - Pune

Tel: 91-20-2566-1512

Fax: 91-20-2566-1513

Japan - Yokohama

Tel: 81-45-471- 6166

Fax: 81-45-471-6122

Korea - Gumi

Tel: 82-54-473-4301

Fax: 82-54-473-4302

Korea - Seoul

Tel: 82-2-554-7200

Fax: 82-2-558-5932 or

82-2-558-5934

Malaysia - Penang

Tel: 60-4-646-8870

Fax: 60-4-646-5086

Philippines - Manila

Tel: 63-2-634-9065

Fax: 63-2-634-9069

Singapore

Tel: 65-6334-8870

Fax: 65-6334-8850

Taiwan - Hsin Chu

Tel: 886-3-572-9526

Fax: 886-3-572-6459

Taiwan - Kaohsiung

Tel: 886-7-536-4818

Fax: 886-7-536-4803

Taiwan - Taipei

Tel: 886-2-2500-6610

Fax: 886-2-2508-0102

Thailand - Bangkok

Tel: 66-2-694-1351

Fax: 66-2-694-1350

EUROPE

Austria - Wels

Tel: 43-7242-2244-39

Fax: 43-7242-2244-393

Denmark - Copenhagen

Tel: 45-4450-2828

Fax: 45-4485-2829

France - Paris

Tel: 33-1-69-53-63-20

Fax: 33-1-69-30-90-79

Germany - Munich

Tel: 49-89-627-144-0

Fax: 49-89-627-144-44

Italy - Milan

Tel: 39-0331-742611

Fax: 39-0331-466781

Netherlands - Drunen

Tel: 31-416-690399

Fax: 31-416-690340

Spain - Madrid

Tel: 34-91-708-08-90

Fax: 34-91-708-08-91

UK - Wokingham

Tel: 44-118-921-5869

Fax: 44-118-921-5820

WORLDWIDE SALES AND SERVICE

12/08/06