FLUKE-190-204/AM-REFURB - Fluke

Fluke 430 Series II

Three-Phase Power Quality

and Energy Analyzers

Technical Data

The new 430 Series II Power Quality and Energy

Analyzers offer the best in power quality analysis

and introduce, for the first time ever, the ability

to monetarily quantify energy losses.

The new Fluke 434, 435 and 437 Series II

models help locate, predict, prevent, and trouble-

shoot power quality problems in three-phase

and single-phase power distribution systems.

Additionally, the Fluke-patented energy loss

algorithm, Unified Power Measurement, measures

and quantifies energy losses due to harmonics

and unbalance issues, allowing the user to pinpoint

the origin of energy waste within a system.

More detailed power quality analysis

capability, and a new Fluke-patented

energy monetization function

• Energy loss calculator: Classic active and

reactive power measurements, unbalance and

harmonic power, are quantified to pinpoint true

system energy losses in dollars (other local

currencies available).

• Power inverter efficiency: Simultaneously

measure AC output power and DC input power

for power electronics systems using optional

DC clamp.

• PowerWave data capture: 435 and 437 Series

II analyzers capture fast RMS data, show

half-cycle and waveforms to characterize

electrical system dynamics (generator start-ups,

UPS switching etc.).

• Waveform capture: 435 and 437 Series II

models capture 50/60 cycles (50/60Hz)

of each event that is detected in all modes,

without set-up.

• Automatic Transient Mode: 435 and 437

Series II analyzers capture 200 kHz waveform

data on all phases simultaneously up to 6 kV.

• Fully Class-A compliant: 435 and 437 Series

II analyzers conduct tests according to the

stringent international IEC 61000-4-30 Class-A

standard.

• Mains signaling: 435 and 437 Series II

analyzers measure interference from ripple

control signals at specific frequencies.

• 400 Hz measurement: 437 Series II analyzer

captures power quality measurements for

avionic and military power systems.

• Troubleshoot: Analyze the trends using the

cursors and zoom tools.

• Highest safety rating in the industry:

600 V CAT IV/1000 V CAT III rated for use

at the service entrance.

• Measure all three phases and neutral:

With included four flexible current probes

with enhanced thin flex designed to fit into

the tightest places.

• Automatic Trending: Every measurement

is always automatically recorded, without

any set-up.

• System-Monitor: Ten power quality

parameters on one screen according to

EN50160 power quality standard.

• Logger function: Configure for any test

condition with memory for up to 600

parameters at user defined intervals.

• View graphs and generate reports:

With included analysis software.

• Battery life: Up to 8 hours operating time

per charge on Li-ion battery pack.

437 Series II

Three-Phase

Power Quality

and Energy

Analyzer will

be available

in early 2012

2 Fluke Corporation Fluke 430 Series II Three-Phase Energy and Power Quality Analyzers

Unified Power Measurement

Fluke’s patented Unified Power Measurement sys-

tem (UPM) provides the most comprehensive view

of power available, measuring:

• Parameters of Classical Power (Steinmetz 1897)

and IEEE 1459-2000 Power

• Detailed Loss Analysis

• Unbalance Analysis

These UPM calculations are used to quantify

the fiscal cost of energy loss caused by power

quality issues. The calculations are computed,

along with other facility-specific information,

by an Energy Loss Calculator that ultimately

determines how much money a facility loses

due to wasted energy.

Energy savings

Traditionally energy savings are achieved by

monitoring and targeting, or in other words, by

finding the major loads in a facility and optimiz-

ing their operation. The cost of power quality

could only be quantified in terms of downtime

caused by lost production and damage to electri-

cal equipment. The Unified Power Measurement

(UPM) method now goes beyond this to achieve

energy savings by discovering the energy waste

caused by power quality issues. Using the

Unified Power Measurement, Fluke’s Energy Loss

Calculator (see screen shot below) will determine

how much money a facility is losing due to waste

energy.

Unbalance

UPM gives a more comprehensive breakdown of

the energy consumed in the plant. In addition to

measuring reactive power (caused by poor power

factor), UPM also measures the energy waste

caused by unbalance; the effect of unevenly

loading each phase in three-phase systems.

Unbalance can often be corrected by reconnect-

ing loads on different phases to ensure the

current drawn on each phase is as equal as

possible. Unbalance can also be corrected by

installing an unbalance reactance device (or

filter), that will minimize the effects. Correcting

unbalance should be basic good housekeeping

in the facility as unbalance problems can cause

motor failure or shorten equipment life expec-

tancy. Unbalance also wastes energy. Using

UPM can minimize or eliminate that energy

waste, thus saving money.

Harmonics

UPM also provides details of the energy wasted

in your facility due to the presence of harmonics.

Harmonics may be present in your facility due to

the loads you operate or may be caused by loads

in adjacent facilities. The presence of harmonics

in your facility can lead to:

• overheating transformers and conductors

• nuisance tripping of circuit breakers

• early failures of electrical equipment

Quantifying the cost of wasted energy due to the

presence of harmonics simplifies the return-on-

investment calculation needed to justify purchas-

ing harmonic filters. By installing a harmonic

filter the ill effects of harmonics can be reduced

and energy waste eliminated, resulting in lower

operational costs and more reliable operation.

Useful kilowatts (power) available ____________

Reactive (unusable) power ____________

Kilowatts made unusable by unbalance issues ____________

Kilowatts made unusable by harmonics ____________

Neutral current ____________

Total cost of wasted kilowatt hours ____________

Energy Loss Calculator

3 Fluke Corporation Fluke 430 Series II Three-Phase Energy and Power Quality Analyzers

Technical specifications

Specifications are valid for models Fluke 434-II, Fluke 435-II, Fluke 437-II unless otherwise specified.

Specificatons for Amp and Watt readings are based upon i430-Flexi-TF unless otherwise specified.

Input characteristics

Voltage inputs

Number of inputs 4 (3 phase + neutral) dc-coupled

Maximum input voltage 1000 Vrms

Nominal voltage range Selectable 1 V to 1000 V

Max. peak measurement voltage 6 kV (transient mode only)

Input impedance 4 MΩ//5 pF

Bandwidth > 10 kHz, up to 100 kHz for transient mode

Scaling 1:1, 10:1, 100:1, 1,000:1 10,000:1 and variable

Current inputs

Number of inputs 4 (3 phase + neutral) dc- or ac-coupled

Type Clamp or current transformer with mV output or i430flex-TF

Range 0.5 Arms to 600 Arms with included i430flex-TF (with sensitivity 10x)

5 Arms to 6000 Arms with included i430flex-TF (with sensitivity 1x)

0.1 mV/A to 1 V/A and custom for use with optional ac or dc clamps

Input impedance 1 MΩ

Bandwidth > 10 kHz

Scaling 1:1, 10:1, 100:1, 1,000:1 10,000:1 and variable

430 Series II Power Quality and Energy Analyzer selection table

Model Fluke 434-II Fluke 435-II Fluke 437-II

Standard compliance IEC 61000-4-30 Class S IEC 61000-4-30 Class A IEC 61000-4-30 Class A

Volt Amp Hz •••

Dips and swells •••

Harmonics •••

Power and energy •••

Energy loss calculator •••

Unbalance •••

Monitor •••

Inrush •••

Event waveform capture • •

Flicker • •

Transients • •

Mains signaling • •

Power wave • •

Power inverter efficiency •••

400Hz •

C1740 Soft Case • •

C437-II Hard Case with rollers •

SD card (Max 32 GB) 8 GB 8 GB 8 GB

All models include the following accessories TL430 test lead set, 4 x i430 thin flexi current probes, BP290 battery, BC430 power adapter with international power adapter set, USB cable

A-B mini and PowerLog CD.

4 Fluke Corporation Fluke 430 Series II Three-Phase Energy and Power Quality Analyzers

Measurement modes

Scope 4 voltage waveforms, 4 current waveforms, Vrms, Vfund. Arms, A fund, V @ cursor, A @ cursor, phase angles

Volts/amps/hertz Vrms phase to phase, Vrms phase to neutral, Vpeak, V Crest Factor, Arms Apeak, A Crest Factor, Hz

Dips and swells Vrms½, Arms½, Pinst with programmable threshold levels for event detection

Harmonics dc, 1 to 50, up to 9th harmonic

for 400 Hz

Harmonics Volts, THD, Harmonic Amps, K factor Amps, Harmonic Watts, THd Watts, K factor Watts, Interharmonic

Volts, Interharmonic Amps, Vrms, Arms (relative to fundamental or to total rms)

Power and energy Vrms, Arms, Wfull, Wfund., VAfull, VAfund., VAharmonics, VAunbalance, var, PF, DPF, CosQ, Efficiency factor,

Wforward, Wreverse

Energy loss calculator Wfund, VAharmonics, VAunbalance, var, A, Loss Active, Loss Reactive, Loss Harmonics, Loss Unbalance, Loss

Neutral, Loss Cost (based upon user defined cost / kWh)

Inverter efficiency

(requires optional dc current clamp)

Wfull, Wfund, Wdc, Efficiency, Vdc, Adc, Vrms, Arms, Hz

Unbalance Vneg%, Vzero%, Aneg%, Azero%, Vfund, Afund, V phase angles, A phase angles

Inrush Inrush current, Inrush duration, Arms½, Vrms½

Monitor Vrms, Arms, harmonic Volts, THD Volts, PLT, Vrms½, Arms½, Hz, dips, swells, interruptions, rapid voltage changes,

unbalance and mains signalling.

All parameters are measured simultaneously in accordance with EN50160

Flagging is applied according to IEC61000-4-30 to indicate unreliable readings due to dips or swells

Flicker (435-II and 437-II only) Pst(1min), Pst, Plt, Pinst, Vrms ½, Arms ½, Hz

Transients (435-II and 437-II only) Transient waveforms 4x Voltage 4x Amps, triggers: Vrms ½, Arms ½, Pinst

Mains Signaling (435-II and 437-II only) Relative signaling voltage and absolute signaling voltage averaged over three seconds for up to two selectable

signaling frequencies

Power Wave (435-II and 437-II only) Vrms½, Arms½ W, Hz and scope waveforms for voltage amps and watts

Logger Custom selection of up to 150 PQ parameters measured simultaneously on 4 phases

Sampling system

Resolution 16 bit analog to digital converter on 8 channels

Maximum sampling speed 200 kS/s on each channel simultaneously

RMS sampling 5000 samples on 10/12 cycles according to IEC61000-4-30

PLL synchronization 4096 samples on 10/12 cycles according to IEC61000-4-7

Nominal frequency 434-II and 435-II: 50 Hz and 60 Hz

437-II: 50 Hz, 60 Hz and 400 Hz

Display modes

Waveform display Available in all modes via SCOPE key

435-II and 437-II: Default display mode for Transients function

Update rate 5x per second

Displays 4 cycles of waveform data on screen, up to 4 waveforms simultaneously

Phasor diagram Available in all modes via Scope waveform display

Default view for Unbalance mode

Meter readings Available in all modes except Monitor and Transients, provides tabulated view of all available readings

Fully customizable up to 150 readings for Logger mode

Trend graph Available in all modes except Transients

Single vertical cursor with min max and avg reading at cursor position

Bar graph Available in Monitor and Harmonics mode

Event list Available in all modes

Provides waveforms on 435II & 437II only.

Input characteristics cont.

5 Fluke Corporation Fluke 430 Series II Three-Phase Energy and Power Quality Analyzers

Product specifications

Model Measurement range Resolution Accuracy

Volt

Vrms (ac+dc) 434-II 1 V to 1000 V phase to neutral 0.1 V ± 0.5 % of nominal voltage****

435-II and 437-II 1 V to 1000 V phase to neutral 0.01 V ± 0.1 % of nominal voltage****

Vpk 1 Vpk to 1400 Vpk 1 V 5 % of nominal voltage

Voltage Crest Factor (CF) 1.0 > 2.8 0.01 ± 5 %

Vrms½ 434-II 1 V to 1000 V phase to neutral 0.1 V ± 1 % of nominal voltage

434-II and 435-II 0.1 V ± 0.2 % of nominal voltage

Vfund 434-II 1 V to 1000 V phase to neutral 0.1 V ± 0.5 % of nominal voltage

435-II and 437-II 0.1 V ± 0.1 % of nominal voltage

Amps (accuracy excluding clamp accuracy)

Amps (ac +dc) i430-Flex 1x 5 A to 6000 A 1 A ± 0.5 % ± 5 counts

i430-Flex 10x 0.5 A to 600 A 0.1 A ± 0.5 % ± 5 counts

1mV/A 1x 5 A to 2000 A 1A ± 0.5 % ± 5 counts

1mV/A 10x 0.5 A A to 200 A (ac only) 0.1 A ± 0.5 % ± 5 counts

Apk i430-Flex 8400 Apk 1 Arms ± 5 %

1mV/A 5500 Apk 1 Arms ± 5 %

A Crest Factor (CF) 1 to 10 0.01 ± 5 %

Amps½ i430-Flex 1x 5 A to 6000 A 1 A ± 1 % ± 10 counts

i430-Flex 10x 0.5 A to 600 A 0.1 A ± 1 % ± 10 counts

1mV/A 1x 5 A to 2000 A 1A ± 1 % ± 10 counts

1mV/A 10x 0.5 A A to 200 A (ac only) 0.1 A ± 1 % ± 10 counts

Afund i430-Flex 1x 5 A to 6000 A 1 A ± 0.5 % ± 5 counts

i430-Flex 10x 0.5 A to 600 A 0.1 A ± 0.5 % ± 5 counts

1mV/A 1x 5 A to 2000 A 1A ± 0.5 % ± 5 counts

1mV/A 10x 0.5 A A to 200 A (ac only) 0.1 A ± 0.5 % ± 5 counts

Hz Fluke 434 @ 50 Hz nominal 42.50 Hz to 57.50 Hz 0.01 Hz ± 0.01 Hz

Fluke 434 @ 60 Hz nominal 51.00 Hz to 69.00 Hz 0.01 Hz ± 0.01 Hz

Fluke 435/7 @ 50 Hz nominal 42.500 Hz to 57.500 Hz 0.001 Hz ± 0.01 Hz

Fluke 435/7 @ 60 Hz nominal 51.000 Hz to 69.000 Hz 0.001 Hz ± 0.01 Hz

Fluke 437 @ 400 Hz nominal 340.0 Hz to 460.0 Hz 0.1 Hz ± 0.1 Hz

Power

Watts (VA, var) i430-Flex max 6000 MW 0.1 W to 1 MW ± 1 % ± 10 counts

1 mV/A max 2000 MW 0.1 W to 1 MW ± 1 % ± 10 counts

Power factor (Cos j/DPF) 0 to 1 0.001 ± 0.1 % @ nominal load conditions

Energy

kWh (kVAh, kvarh) i430-Flex 10x Depends on clamp scaling and V nominal ± 1 % ± 10 counts

Energy loss i430-Flex 10x Depends on clamp scaling and V nominal ± 1 % ± 10 counts

Excluding line resistance accuracy

Harmonics

Harmonic order (n) DC, 1 to 50 Grouping: Harmonic groups according to IEC 61000-4-7

Inter-harmonic order (n) OFF, 1 to 50 Grouping: Harmonic and Interharmonic subgroups according to IEC 61000-4-7

Volts %f 0.0 % to 100 % 0.1 % ± 0.1 % ± n x 0.1 %

%r 0.0 % to 100 % 0.1 % ± 0.1 % ± n x 0.4 %

Absolute 0.0 to 1000 V 0.1 V ± 5 % *

THD 0.0 % to 100 % 0.1 % ± 2.5 %

Amps %f 0.0 % to 100 % 0.1 % ± 0.1 % ± n x 0.1 %

%r 0.0 % to 100 % 0.1 % ± 0.1 % ± n x 0.4 %

Absolute 0.0 to 600 A 0.1 A ± 5 % ± 5 counts

THD 0.0 % to 100 % 0.1 % ± 2.5 %

Watts %f or %r 0.0 % to 100 % 0.1 % ± n x 2 %

Absolute Depends on clamp scaling and V nominal —± 5 % ± n x 2 % ± 10 counts

THD 0.0 % to 100 % 0.1 % ± 5 %

Phase Angle -360° to +0° 1° ± n x 1°

6 Fluke Corporation Fluke 430 Series II Three-Phase Energy and Power Quality Analyzers

Flicker

Plt, Pst, Pst(1min) Pinst 0.00 to 20.00 0.01 ± 5 %

Unbalance

Volts % 0.0 % to 20.0 % 0.1 % ± 0.1 %

Amps % 0.0 % to 20.0 % 0.1% ± 1 %

Mains signaling

Threshold levels Threshold, limits and signaling duration is

programable for two signaling frequencies

— —

Signaling frequency 60 Hz to 3000 Hz 0.1 Hz

Relative V% 0 % to 100 % 0.10 % ± 0.4 %

Absolute V3s (3 second avg.) 0.0 V to 1000 V 0.1 V ± 5 % of nominal voltage

Trend recording

Method Automatically records min, max and average values over time for all readings being displayed for the three phases and neutral

simultaneously

Sampling 5 readings/s continuous sampling per channel, 100/120** reading/s for 1/2 cycle values and Pinst

Recording time 1 hr up to 1 year, user selectable (default setting 7 days)

Averaging time Minimum of 1 second

Memory Data is stored on SDcard (8GB included 32GB max)

Events 434-II: Tabulated in event list

435-II & 437-II: Tabulated in event list, including 50/60** waveform cycles and 7.5s 1/2 cycle rms Voltage and Amps trend

Measurement method

Vrms, Arms 10/12 cycle contiguous non-overlapping intervals using 500/4162 samples per cycle in accordance with IEC 61000-4-30

Vpeak, Apeak Absolute highest sample value within 10/12 cycle interval with 40 μs sample resolution

V Crest Factor Measures ratio between the Vpeak and Vrms

A Crest Factor Measures ratio between the Apeak and Arms

Hz Measured every 10 sec in accordance with IEC61000-4-30. Vrms½, Arms½ Value is measured over 1 cycle, commencing at a

fundamental zero crossing, and refreshed each half-cycle.

This technique is independent for each channel in accordance with IEC 61000-4-30.

Harmonics Calculated from 10/12-cycle gapless harmonic group measurements on Voltage and Amps according to IEC 61000-4-7

Watt Full and fundamental real power display. Calculates average value of instantaneous power over 10/12 cycle period for each

phase. Total Active Power PT = P1 + P2 + P3.

VA Full and fundamental apparent power display. Calculates apparent power using Vrms x Arms value over 10/12 cycle period.

var Fundamental reactive power display. Calculates reactive power on fundamental positive sequence components. Capacitive and

inductive load is indicated with capacitor and inductor icons.

VA Harmonics Total disturbance power due to harmonics. Calculated for each phase and for total system based upon total apparent power and

fundamental real power.

VA Unbalance Unbalance power for total sytem. Calculated using symmetrical components method for fundamental apparent power and total

apparent power.

Power factor Calculated total watt/VA

Cos jCosine of angle between fundamental voltage and current

DPF Calculated fundamental Watt/VA

Energy/energy cost Power values are accumulated over time for kWh values. Energy cost is calculated from user defined /kWh cost variable

Unbalance The supply voltage unbalance is evaluated using the method of symmetrical components according to IEC61000-4-30

Flicker According to IEC 61000-4-15 flickermeter—functional and design specification.

Includes 230 V 50 Hz lamp and 120 V 60 Hz lamp models.

Transient capture Captures waveform triggered on signal envelope. Additionally triggers on dips, swells, interruptions and Amps level

Inrush current The inrush current begins when the Arms half cycle rises above the inrush threshold, and ends when the Arms half cycle

rms is equal to or below the inrush threshold minus a user-selected hysteresis value. The measurement is the square root of

the mean of the squared Arms half cycle values measured during the inrush duration. Each half-cycle interval is contiguous

and non-overlapping as recommended by IEC 61000-4-30. Markers indicate inrush duration. Cursors allow measurement of

peak Arms half cycle.

Mains signaling Measurements are based on: either the corresponding 10/12-cycle rms value interharmonic bin or the rms of the four nearest

10/12-cycle rms value interharmonic bins per IEC 61000-4-30. Limit setup for Monitor mode follows EN50160 standard limits.

Time synchronization Optional GPS430-II timesync module provides time uncertainty ≤ 20 ms or ≤ 16.7 ms for time tagging of events and time

aggregated measurements. When synchronization is not available, time tolerance is ≤ 1-s/24h

Product specifications cont.

7 Fluke Corporation Fluke 430 Series II Three-Phase Energy and Power Quality Analyzers

Environmental

Operating temperature 0 °C ~ +40 °C; +40 °C ~ +50 °C excl. battery

Storage temperature -20 °C ~ +60 °C

Humidity +10 °C ~ +30 °C: 95 % RH non-condensing

+30 °C ~ +40 °C: 75 % RH non-condensing

+40 °C ~ +50 °C: 45 % RH non-condensing

Maximum operating altitude Up to 2,000 m (6666 ft) for CAT IV 600 V, CAT III 1000 V

Up to 3,000 m (10,000 ft) for CAT III 600 V, CAT II 1000 V

Maximum storage altitude 12 km (40,000 ft)

Electro-Magnetic-Compatibility

(EMC)

EN 61326 (2005-12) for emission and immunity

Interfaces mini-USB-B, Isolated USB port for PC connectivity

SD card slot accessible behind instrument battery

Warranty Three years (parts and labor) on main instrument, one year on accessories

Included accessories

Power options BC430 Power Adapter

International plug adapter set

BP290 (Single capacity Li-ion battery) 28Wh (Up to 8 hours)

Leads TL430 Test lead and Alligator clip set

Color coding WC100 color coding clips and regional decals

Flexible current probes i430flex-TF, 24 inch (61cm) length, 4 clamps

Memory, Software and

PC connection

8 GB SD card

PowerLog on CD (includes operator manuals in PDF format)

USB cable A-Bmini

Carrying case C1740 Soft Case for 434-II and 435-II

C437 Hard Case with rollers for 437-II

* ± 5 % if ≥ 1 % of nominal voltage ± 0.05 % of nominal voltage if < 1% of nominal voltage

** 50Hz/60Hz nominal frequency according to IEC 61000-4-30

*** 400Hz measurements are not supported for Flicker, Mains Signaling and Monitor Mode.

**** for nominal voltage 50 V to 500 V

Wiring configurations

1Ø + NEUTRAL Single phase with neutral

1Ø SPLIT PHASE Split phase

1Ø IT NO NEUTRAL Single phase system with two phase voltages without neutral

3Ø WYE Three phase four wire system WYE

3Ø DELTA Three phase three wire system Delta

3Ø IT Three phase system without neutral WYE

3Ø HIGH LEG Four wire three phase Delta system with center tapped high leg

3Ø OPEN LEG Open delta three wire system with 2 transformer windings

2-ELEMENT Three phase three wire system without current sensor on phase L2/B (2 watt meter method)

2½-ELEMENT Three phase four wire system without voltage sensor on phase L2/B

INVERTER EFFICIENCY dc voltage and current input with ac output power (automatically displayed and selected in Inverter Efficiency mode)

General specifications

Case Design Rugged, shock proof with integrated protective holster

Drip and dust proof IP51 according to IEC60529 when used in tilt stand position

Shock and vibration Shock 30 g, vibration: 3 g sinusoid, random 0.03 g2/Hz according to MIL-PRF-28800F Class 2

Display Brightness: 200 cd/m2 typ. using power adapter, 90 cd/m2 typical using battery power

Size: 127 mm x 88 mm (153 mm/6.0 in diagonal) LCD

Resolution: 320 x 240 pixels

Contrast and brightness: user-adjustable, temperature compensated

Memory 8GB SD card (SDHC compliant, FAT32 formatted) standard, upto 32GB optionally

Screen save and multiple data memories for storing data including recordings (dependent on memory size)

Real-time clock Time and date stamp for Trend mode, Transient display, System Monitor and event capture

Ordering information

Fluke-434-II Three-Phase Energy Analyzer

Fluke-435-II Three-Phase Power Quality and Energy Analyzer

Fluke-437-II 400 Hz Three-Phase Power Quality and Energy Analyzer

Optional/replacement accessories

I430-FLEXI-TF-4PK 6000 A Fluke 430 Thin Flexi 61 cm (24 in) 4 pack

C437-II Hard Case 430 Series II with roller

C1740 Softcase for 174X and 43X-II PQ Analyzer

i5sPQ3 i5sPQ3, 5 A ac Current Clamps, 3-pack

i400s i400s AC Current Clamp

WC100 WC100 Color Localization Set

GPS430-II GPS430 Time Synchronization Module

BP291 Double capacity Li-ion battery (up to 16 hr)

HH290 Hanging hook for use on cabinet doors

Fluke Corporation

PO Box 9090, Everett, WA 98206 U.S.A.

Fluke Europe B.V.

PO Box 1186, 5602 BD

Eindhoven, The Netherlands

Fluke. The Most Trusted Tools in the World.

For more information call:

In the U.S.A. (800) 443-5853 or

Fax (425) 446-5116

In Europe/M-East/Africa +31 (0) 40 2675 200 or

Fax +31 (0) 40 2675 222

In Canada (800)-36-FLUKE or

Fax (905) 890-6866

From other countries +1 (425) 446-5500 or

Fax +1 (425) 446-5116

Web access: http://www.fluke.com

Speciﬁcations subject to change without notice.

Printed in U.S.A. 6/2012 2643006E D-EN

Pub ID 11858-eng

Modification of this document is not

permitted without written permission

from Fluke Corporation.

Flexible Current Probe i430 Flexi-TF specification

General specifications

Probe and cable material Alcryn 2070NC, reinforced insulation, UL94 V0, Color: RED

Couplings material Lati Latamid 6H-V0 Nylon

Probe cable length 610 mm (24 in)

Probe cable diameter 12.4 mm (0.49 in)

Probe cable bend radius 38.1 mm (1.5 in)

Output cable length 2.5 meters RG58

Output connector Safety BNC connector

Operating range -20 °C to +90 °C

Storage temperature -40 °C to +105°C

Operating humidity 15 % to 85 % (non condensing)

Degree of protection (Probe) IP41

Specifications

Current range 6000 A AC RMS

Voltage output (@1000 ARMS, 50 Hz) 86.6 mV

Accuracy ± 1 % of reading(@ 25 °C, 50 Hz)

Linearity (10 % to 100 % of range) ± 0.2 % of reading

Noise (10 Hz – 7 kHz) 1.0 mV ACRMS

Output impedance 82 Ω min

Load impedance 50 MΩ

Internal Resistance per 100 mm probe

length

10.5Ω ± 5 %

Bandwidth (-3dB) 10 Hz to 7 kHz

Phase error (45 Hz – 65 Hz) ± 1°

Position sensitivity ± 2 % of reading max.

Temperature coefficient ± 0.08 % max of reading per °C

Working voltage

(see safety standards section)

1000 V AC RMS or DC (head)

30 V max. (output)