87LPC764
Low power, low price, low pin count
(20 pin) microcontroller with 4 kB OTP
Preliminary specification
Supersedes data of 2000 Apr 14
IC28 Data Handbook
2000 Jun 01
INTEGRATED CIRCUITS
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 i
GENERAL DESCRIPTION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FEATURES 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING INFORMATION 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIN CONFIGURATION, 20-PIN DIP AND SO PACKAGES 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LOGIC SYMBOL 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BLOCK DIAGRAM 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PIN DESCRIPTIONS 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL FUNCTION REGISTERS 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FUNCTIONAL DESCRIPTION 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enhanced CPU 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Functions 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Comparators 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparator Configuration 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Reference Voltage 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparator Interrupt 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparators and Power Reduction Modes 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Comparator Configuration Example 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Serial Interface 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I2C Interrupts 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reading I2CON 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking ATN and DRDY 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Writing I2CON 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regarding Transmit Active 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Regarding Software Response Time 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interrupts 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Interrupt Inputs 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O Ports 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quasi-Bidirectional Output Configuration 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Open Drain Output Configuration 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Push-Pull Output Configuration 18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Keyboard Interrupt (KBI) 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Frequency Oscillator Option 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Medium Frequency Oscillator Option 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
High Frequency Oscillator Option 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-Chip RC Oscillator Option 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Clock Input Option 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock Output 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CPU Clock Modification: CLKR and DIVM 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Monitoring Functions 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brownout Detection 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power On Detection 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Reduction Modes 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Mode 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Down Mode 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Low Voltage EPROM Operation 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T imer/Counters 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 0 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 1 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 2 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 3 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Timer Overflow Toggle Output 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UART 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 ii
Mode 0 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 1 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 2 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mode 3 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Serial Port Control Register (SCON) 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud Rates 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using Timer 1 to Generate Baud Rates 32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
More About UART Mode 0 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
More About UART Mode 1 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
More About UART Modes 2 and 3 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Multiprocessor Communications 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatic Address Recognition 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Timer 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Feed Sequence 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Watchdog Reset 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Additional Features 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Software Reset 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dual Data Pointers 42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
EPROM Characteristics 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32-Byte Customer Code Space 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System Configuration Bytes 43. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security Bits 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABSOLUTE MAXIMUM RATINGS 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DC ELECTRICAL CHARACTERISTICS 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COMPARATOR ELECTRICAL CHARACTERISTICS 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AC ELECTRICAL CHARACTERISTICS 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
1
2000 Jun 01
GENERAL DESCRIPTION
The 87LPC764 is a 20-pin single-chip microcontroller designed for
low pin count applications demanding high-integration, low cost
solutions over a wide range of performance requirements. A
member of the Philips low pin count family, the 87LPC764 offers
programmable oscillator configurations for high and low speed
crystals or RC operation, wide operating voltage range,
programmable port output configurations, selectable Schmitt trigger
inputs, LED drive outputs, and a built-in watchdog timer. The
87LPC764 is based on an accelerated 80C51 processor
architecture that executes instructions at twice the rate of standard
80C51 devices.
FEATURES
•An accelerated 80C51 CPU provides instruction cycle times of
300–600 ns for all instructions except multiply and divide when
executing at 20 MHz. Execution at up to 20 MHz when
VDD = 4.5 V to 6.0 V, 10 MHz when VDD = 2.7 V to 6.0 V.
•2.7 V to 6.0 V operating range for digital functions.
•4 K bytes EPROM code memory.
•128 byte RAM data memory.
•32-byte customer code EPROM allows serialization of devices,
storage of setup parameters, etc.
•Two 16-bit counter/timers. Each timer may be configured to toggle
a port output upon timer overflow.
•Two analog comparators.
•Full duplex UART.
•I2C communication port.
•Eight keypad interrupt inputs, plus two additional external interrupt
inputs.
•Four interrupt priority levels.
•W atchdog timer with separate on-chip oscillator, requiring no
external components. The watchdog timeout time is selectable
from 8 values.
•Active low reset. On-chip power-on reset allows operation with no
external reset components.
•Low voltage reset. One of two preset low voltage levels may be
selected to allow a graceful system shutdown when power fails.
May optionally be configured as an interrupt.
•Oscillator Fail Detect. The watchdog timer has a separate fully
on-chip oscillator, allowing it to perform an oscillator fail detect
function.
•Configurable on-chip oscillator with frequency range and RC
oscillator options (selected by user programmed EPROM bits).
The RC oscillator option allows operation with no external
oscillator components.
•Programmable port output configuration options:
quasi-bidirectional, open drain, push-pull, input-only.
•Selectable Schmitt trigger port inputs.
•LED drive capability (20 mA) on all port pins.
•Controlled slew rate port outputs to reduce EMI. Outputs have
approximately 10 ns minimum ramp times.
•15 I/O pins minimum. Up to 18 I/O pins using on-chip oscillator
and reset options.
•Only power and ground connections are required to operate the
87LPC764 when fully on-chip oscillator and reset options are
selected.
•Serial EPROM programming allows simple in-circuit production
coding. Two EPROM security bits prevent reading of sensitive
application programs.
•Idle and Power Down reduced power modes. Improved wakeup
from Power Down mode (a low interrupt input starts execution).
Typical Power Down current is 1 µA.
•20-pin DIP and SO packages.
ORDERING INFORMATION
Part Number Temperature Range °C and Package Frequency Drawing Number
P87LPC764B N 0 to +70, Plastic Dual In-Line Package 20 MHz (5 V), 10 MHz (3 V) SOT146–1
P87LPC764B D 0 to +70, Plastic Small Outline Package 20 MHz (5 V), 10 MHz (3 V) SOT163–1
P87LPC764F N –45 to +85, Plastic Dual In-Line Package 20 MHz (5 V), 10 MHz (3 V) SOT146–1
P87LPC764F D –45 to +85, Plastic Small Outline Package 20 MHz (5 V), 10 MHz (3 V) SOT163–1
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 2
PIN CONFIGURATION, 20-PIN DIP AND SO PACKAGES
SU01149
1
2
3
4
5
6
7
8
9
11
12
13
14
15
16
17
18
19
20
CMP2/P0.0
P1.7
P1.6
RST/P1.5
VSS
X1/P2.1
X2/CLKOUT/P2.0
INT1/P1.4
SDA/INT0/P1.3
SCL/T0/P1.2
P0.1/CIN2B
P0.2/CIN2A
P0.3/CIN1B
P0.4/CIN1A
P0.5/CMPREF
VDD
P0.6/CMP1
P1.0/TxD
P0.7/T1
P1.1/RxD
10
LOGIC SYMBOL
T1
X1
SU01150
VDD VSS
TxDCMP2
CIN2B
CIN2A
CIN1B
CIN1A
CMPREF
CMP1
CLKOUT/X2
PORT 0PORT 2
PORT 1
RxD
INT0
RST
INT1
T0 SCL
SDA
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 3
BLOCK DIAGRAM
SU01151
TIMER 0, 1
I2C
UART
ACCELERATED
80C51 CPU
WATCHDOG TIMER
AND OSCILLATOR
PORT 0
CONFIGURABLE I/OS
128 BYTE
DATA RAM
4K BYTE
CODE EPROM
INTERNAL BUS
ANALOG
COMPARATORS
PORT 1
CONFIGURABLE I/OS
KEYPAD
INTERRUPT
PORT 2
CONFIGURABLE I/OS
POWER MONITOR
(POWER-ON RESET,
BROWNOUT RESET)
CONFIGURABLE
OSCILLATOR
CRYSTAL OR
RESONATOR
ON-CHIP
R/C
OSCILLATOR
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 4
SU01216
UNUSED CODE
MEMORY SPACE
32-BYTE CUSTOMER
CODE SPACE
(ACCESSIBLE VIA MOVC)
UNUSED CODE
MEMORY SPACE
4 K BYTES ON-CHIP
CODE MEMORY
INTERRUPT VECTORS
SPECIAL FUNCTION
REGISTERS
(ONLY DIRECTLY
ADDRESSABLE)
128 BYTES ON-CHIP DATA
MEMORY
(DIRECTLY AND
INDIRECTLY
ADDRESSABLE)
16-BIT ADDRESSABLE BYTES
UNUSED SPACE
CONFIGURATION BYTES
UCFG1, UCFG2
(ACCESSIBLE VIA MOVX)
UNUSED SPACE
FFFFh
FCFFh
FCE0h
1000h
0FFFh
FFh
80h
7Fh
0000h 00h 0000h
FD00h
FD01h
FFFFh
* The 87LPC764 does not support access to external data memory. However, the User Configuration Bytes
are accessed via the MOVX instruction as if they were in external data memory.
ON-CHIP CODE
MEMORY SPACE ON-CHIP DATA
MEMORY SPACE EXTERNAL DATA
MEMORY SPACE*
Figure 1. 87LPC764 Program and Data Memory Map
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 5
PIN DESCRIPTIONS
MNEMONIC PIN NO. TYPE NAME AND FUNCTION
P0.0–P0.7 1, 13, 14,
16–20 I/O Port 0: Port 0 is an 8-bit I/O port with a user-configurable output type. Port 0 latches are configured in
the quasi-bidirectional mode and have either ones or zeros written to them during reset, as determined
by the PRHI bit in the UCFG1 configuration byte. The operation of port 0 pins as inputs and outputs
depends upon the port configuration selected. Each port pin is configured independently. Refer to the
section on I/O port configuration and the DC Electrical Characteristics for details.
The Keyboard Interrupt feature operates with port 0 pins.
Port 0 also provides various special functions as described below.
1 O P0.0 CMP2 Comparator 2 output.
20 IP0.1 CIN2B Comparator 2 positive input B.
19 IP0.2 CIN2A Comparator 2 positive input A.
18 IP0.3 CIN1B Comparator 1 positive input B.
17 IP0.4 CIN1A Comparator 1 positive input A.
16 IP0.5 CMPREF Comparator reference (negative) input.
14 OP0.6 CMP1 Comparator 1 output.
13 I/O P0.7 T1 T imer/counter 1 external count input or overflow output.
P1.0–P1.7 2–4, 8–12 I/O Port 1: Port 1 is an 8-bit I/O port with a user-configurable output type, except for three pins as noted
below. Port 1 latches are configured in the quasi-bidirectional mode and have either ones or zeros
written to them during reset, as determined by the PRHI bit in the UCFG1 configuration byte. The
operation of the configurable port 1 pins as inputs and outputs depends upon the port configuration
selected. Each of the configurable port pins are programmed independently. Refer to the section on I/O
port configuration and the DC Electrical Characteristics for details.
Port 1 also provides various special functions as described below.
12 OP1.0 TxD T ransmitter output for the serial port.
11 IP1.1 RxD Receiver input for the serial port.
10 I/O
I/O P1.2 T0 T imer/counter 0 external count input or overflow output.
SCL I2C serial clock input/output. When configured as an output, P1.2 is open
drain, in order to conform to I2C specifications.
9 I
I/O P1.3 INT0 External interrupt 0 input.
SDA I2C serial data input/output. When configured as an output, P1.3 is open
drain, in order to conform to I2C specifications.
8 I P1.4 INT1 External interrupt 1 input.
4 I P1.5 RST External Reset input (if selected via EPROM configuration). A low on this pin
resets the microcontroller, causing I/O ports and peripherals to take on their
default states, and the processor begins execution at address 0. When used
as a port pin, P1.5 is a Schmitt trigger input only.
P2.0–P2.1 6, 7 I/O Port 2: Port 2 is a 2-bit I/O port with a user-configurable output type. Port 2 latches are configured in the
quasi-bidirectional mode and have either ones or zeros written to them during reset, as determined by
the PRHI bit in the UCFG1 configuration byte. The operation of port 2 pins as inputs and outputs
depends upon the port configuration selected. Each port pin is configured independently. Refer to the
section on I/O port configuration and the DC Electrical Characteristics for details.
Port 2 also provides various special functions as described below.
7 O P2.0 X2 Output from the oscillator amplifier (when a crystal oscillator option is
selected via the EPROM configuration).
CLKOUT CPU clock divided by 6 clock output when enabled via SFR bit and in
conjunction with internal RC oscillator or external clock input.
6 I P2.1 X1 Input to the oscillator circuit and internal clock generator circuits (when
selected via the EPROM configuration).
VSS 5 I Ground: 0V reference.
VDD 15 I Power Supply: This is the power supply voltage for normal operation as well as Idle and
Power Down modes.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 6
SPECIAL FUNCTION REGISTERS
Name Description SFR
Address Bit Functions and Addresses
MSB LSB Reset
Value
E7 E6 E5 E4 E3 E2 E1 E0
ACC* Accumulator E0h 00h
AUXR1# Auxiliary Function Register A2h KBF BOD BOI LPEP SRST 0 – DPS 02h1
F7 F6 F5 F4 F3 F2 F1 F0
B* B register F0h 00h
CMP1# Comparator 1 control
register ACh – – CE1 CP1 CN1 OE1 CO1 CMF1 00h1
CMP2# Comparator 2 control
register ADh – – CE2 CP2 CN2 OE2 CO2 CMF2 00h1
DIVM# CPU clock divide-by-M
control 95h 00h
DPTR: Data pointer (2 bytes)
DPH Data pointer high byte 83h 00h
DPL Data pointer low byte 82h 00h
CF CE CD CC CB CA C9 C8
I2CFG#* I2C configuration register C8h/RD SLAVEN MASTRQ 0 TIRUN – – CT1 CT0 00h1
C8h/WR SLAVEN MASTRQ CLRTI TIRUN – – CT1 CT0
DF DE DD DC DB DA D9 D8
I2CON#* I2C control register D8h/RD RDAT ATN DRDY ARL STR STP MASTER – 80h1
D8h/WR CXA IDLE CDR CARL CSTR CSTP XSTR XSTP
I2DAT# I2C data register D9h/RD RDAT 0 0 0 0 0 0 0 80h
D9h/WR XDAT x x x x x x x
AF AE AD AC AB AA A9 A8
IEN0* Interrupt enable 0 A8h EA EWD EBO ES ET1 EX1 ET0 EX0 00h
EF EE ED EC EB EA E9 E8
IEN1#* Interrupt enable 1 E8h ETI – EC1 – – EC2 EKB EI2 00h1
BF BE BD BC BB BA B9 B8
IP0* Interrupt priority 0 B8h – PWD PBO PS PT1 PX1 PT0 PX0 00h1
IP0H# Interrupt priority 0 high byte B7h – PWDH PBOH PSH PT1H PX1H PT0H PX0H 00h1
FF FE FD FC FB FA F9 F8
IP1* Interrupt priority 1 F8h PTI – PC1 – – PC2 PKB PI2 00h1
IP1H# Interrupt priority 1 high byte F7h PTIH – PC1H – – PC2H PKBH PI2H 00h1
KBI# Keyboard Interrupt 86h 00h
87 86 85 84 83 82 81 80
P0* Port 0 80h T1 CMP1 CMPREF CIN1A CIN1B CIN2A CIN2B CMP2 Note 2
97 96 95 94 93 92 91 90
P1* Port 1 90h (P1.7) (P1.6) RST INT1 INT0 T0 RxD TxD Note 2
A7 A6 A5 A4 A3 A2 A1 A0
P2* Port 2 A0h – – – – – – X1 X2 Note 2
P0M1# Port 0 output mode 1 84h (P0M1.7) (P0M1.6) (P0M1.5) (P0M1.4) (P0M1.3) (P0M1.2) (P0M1.1) (P0M1.0) 00h
P0M2# Port 0 output mode 2 85h (P0M2.7) (P0M2.6) (P0M2.5) (P0M2.4) (P0M2.3) (P0M2.2) (P0M2.1) (P0M2.0) 00H
P1M1# Port 1 output mode 1 91h (P1M1.7) (P1M1.6) –(P1M1.4) – – (P1M1.1) (P1M1.0) 00h1
P1M2# Port 1 output mode 2 92h (P1M2.7) (P1M2.6) –(P1M2.4) – – (P1M2.1) (P1M2.0) 00h1
P2M1# Port 2 output mode 1 A4h P2S P1S P0S ENCLK T1OE T0OE (P2M1.1) (P2M1.0) 00h
P2M2# Port 2 output mode 2 A5h – – – – – – (P2M2.1) (P2M2.0) 00h1
PCON Power control register 87h SMOD1 SMOD0 BOF POF GF1 GF0 PD IDL Note 3
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 7
Name Reset
Value
Bit Functions and Addresses
MSB LSB
SFR
Address
Description
D7 D6 D5 D4 D3 D2 D1 D0
PSW* Program status word D0h CY AC F0 RS1 RS0 OV F1 P 00h
PT0AD# Port 0 digital input disable F6h 00h
9F 9E 9D 9C 9B 9A 99 98
SCON* Serial port control 98h SM0 SM1 SM2 REN TB8 RB8 TI RI 00h
SBUF Serial port data buffer
register 99h xxh
SADDR# Serial port address register A9h 00h
SADEN# Serial port address enable B9h 00h
SP Stack pointer 81h 07h
8F 8E 8D 8C 8B 8A 89 88
TCON* T imer 0 and 1 control 88h TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00h
TH0 Timer 0 high byte 8Ch 00h
TH1 Timer 1 high byte 8Dh 00h
TL0 T imer 0 low byte 8Ah 00h
TL1 T imer 1 low byte 8Bh 00h
TMOD T imer 0 and 1 mode 89h GATE C/T M1 M0 GA TE C/T M1 M0 00h
WDCON# W atchdog control register A7h – – WDOVF WDRUN WDCLK WDS2 WDS1 WDS0 Note 4
WDRST# W atchdog reset register A6h xxh
NOTES:
* SFRs are bit addressable.
# SFRs are modified from or added to the 80C51 SFRs.
1. Unimplemented bits in SFRs are X (unknown) at all times. Ones should not be written to these bits since they may be used for other
purposes in future derivatives. The reset value shown in the table for these bits is 0.
2. I/O port values at reset are determined by the PRHI bit in the UCFG1 configuration byte.
3. The PCON reset value is x x BOF POF–0 0 0 0b. The BOF and POF flags are not affected by reset. The POF flag is set by hardware upon
power up. The BOF flag is set by the occurrence of a brownout reset/interrupt and upon power up.
4. The WDCON reset value is xx11 0000b for a Watchdog reset, xx01 0000b for all other reset causes if the watchdog is enabled, and xx00
0000b for all other reset causes if the watchdog is disabled.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 8
FUNCTIONAL DESCRIPTION
Details of 87LPC764 functions will be described in the following
sections.
Enhanced CPU
The 87LPC764 uses an enhanced 80C51 CPU which runs at twice the
speed of standard 80C51 devices. This means that the performance of
the 87LPC764 running at 5 MHz is exactly the same as that of a
standard 80C51 running at 10 MHz. A machine cycle consists of 6
oscillator cycles, and most instructions execute in 6 or 12 clocks. A
user configurable option allows restoring standard 80C51 execution
timing. In that case, a machine cycle becomes 12 oscillator cycles.
In the following sections, the term “CPU clock” is used to refer to the
clock that controls internal instruction execution. This may
sometimes be different from the externally applied clock, as in the
case where the part is configured for standard 80C51 timing by
means of the CLKR configuration bit or in the case where the clock
is divided down via the setting of the DIVM register. These features
are described in the Oscillator section.
Analog Functions
The 87LPC764 incorporates two Analog Comparators. In order to
give the best analog function performance and to minimize power
consumption, pins that are actually being used for analog functions
must have the digital outputs and the digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input
Only (high impedance) mode as described in the I/O Ports section.
Digital inputs on port 0 may be disabled through the use of the
PT0AD register. Each bit in this register corresponds to one pin of
Port 0. Setting the corresponding bit in PT0AD disables that pin’s
digital input. Port bits that have their digital inputs disabled will be
read as 0 by any instruction that accesses the port.
Analog Comparators
Two analog comparators are provided on the 87LPC764. Input and
output options allow use of the comparators in a number of different
configurations. Comparator operation is such that the output is a
logical one (which may be read in a register and/or routed to a pin)
when the positive input (one of two selectable pins) is greater than
the negative input (selectable from a pin or an internal reference
voltage). Otherwise the output is a zero. Each comparator may be
configured to cause an interrupt when the output value changes.
Comparator Configuration
Each comparator has a control register, CMP1 for comparator 1 and
CMP2 for comparator 2. The control registers are identical and are
shown in Figure 2.
The overall connections to both comparators are shown in Figure 3.
There are eight possible configurations for each comparator, as
determined by the control bits in the corresponding CMPn register:
CPn, CNn, and OEn. These configurations are shown in Figure 4.
The comparators function down to a VDD of 3.0V.
When each comparator is first enabled, the comparator output and
interrupt flag are not guaranteed to be stable for 10 microseconds.
The corresponding comparator interrupt should not be enabled
during that time, and the comparator interrupt flag must be cleared
before the interrupt is enabled in order to prevent an immediate
interrupt service.
BIT SYMBOL FUNCTION
CMPn.7, 6 — Reserved for future use. Should not be set to 1 by user programs.
CMPn.5 CEn Comparator enable. When set by software, the corresponding comparator function is enabled.
Comparator output is stable 10 microseconds after CEn is first set.
CMPn.4 CPn Comparator positive input select. When 0, CINnA is selected as the positive comparator input. When
1, CINnB is selected as the positive comparator input.
CMPn.3 CNn Comparator negative input select. When 0, the comparator reference pin CMPREF is selected as
the negative comparator input. When 1, the internal comparator reference Vref is selected as the
negative comparator input.
CMPn.2 OEn Output enable. When 1, the comparator output is connected to the CMPn pin if the comparator is
enabled (CEn = 1). This output is asynchronous to the CPU clock.
CMPn.1 COn Comparator output, synchronized to the CPU clock to allow reading by software. Cleared when the
comparator is disabled (CEn = 0).
CMPn.0 CMFn Comparator interrupt flag. This bit is set by hardware whenever the comparator output COn changes
state. This bit will cause a hardware interrupt if enabled and of sufficient priority. Cleared by
software and when the comparator is disabled (CEn = 0).
CMFn
SU01152
COnOEnCNnCPnCEn——
01234567
CMPn Reset Value: 00h
Not Bit Addressable
Address: ACh for CMP1, ADh for CMP2
Figure 2. Comparator Control Registers (CMP1 and CMP2)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 9
SU01153
+
–
(P0.4) CIN1A
COMPARATOR 1
(P0.3) CIN1B CO1
OE1
(P0.5) CMPREF
+
–
(P0.2) CIN2A
COMPARATOR 2
(P0.1) CIN2B CO2
OE2
CP1
CN1
CP2
CN2
CMP2 (P0.0)
CMP1 (P0.6)
CHANGE DETECT
CMF1 INTERRUPT
CHANGE DETECT
CMF2 INTERRUPT
Vref
Figure 3. Comparator Input and Output Connections
Vref (1.23V) Vref (1.23V)
Vref (1.23V)
SU01154
+
–
CINnA
CMPREF COn
CPn, CNn, OEn = 0 0 0
+
–
CINnA
CMPREF CMPn
COn
CPn, CNn, OEn = 0 0 1
+
–
CINnA CMPn
COn
CPn, CNn, OEn = 0 1 1
+
–
CINnB
CMPREF CMPn
COn
CPn, CNn, OEn = 1 0 1
+
–
CINnB CMPn
COn
CPn, CNn, OEn = 1 1 1
CPn, CNn, OEn = 0 1 0
CPn, CNn, OEn = 1 0 0
CPn, CNn, OEn = 1 1 0
+
–
CINnA
Vref (1.23V) COn
+
–
CINnB
CMPREF COn
+
–
CINnB COn
Figure 4. Comparator Configurations
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 10
Internal Reference Voltage
An internal reference voltage generator may supply a default
reference when a single comparator input pin is used. The value of
the internal reference voltage, referred to as Vref, is 1.28 V ±10%.
Comparator Interrupt
Each comparator has an interrupt flag CMFn contained in its
configuration register. This flag is set whenever the comparator
output changes state. The flag may be polled by software or may be
used to generate an interrupt. The interrupt will be generated when
the corresponding enable bit ECn in the IEN1 register is set and the
interrupt system is enabled via the EA bit in the IEN0 register.
Comparators and Power Reduction Modes
Either or both comparators may remain enabled when Power Down
or Idle mode is activated. The comparators will continue to function
in the power reduction mode. If a comparator interrupt is enabled, a
change of the comparator output state will generate an interrupt and
wake up the processor. If the comparator output to a pin is enabled,
the pin should be configured in the push-pull mode in order to obtain
fast switching times while in power down mode. The reason is that
with the oscillator stopped, the temporary strong pull-up that
normally occurs during switching on a quasi-bidirectional port pin
does not take place.
Comparators consume power in Power Down and Idle modes, as
well as in the normal operating mode. This fact should be taken into
account when system power consumption is an issue.
Comparator Configuration Example
The code shown in Figure 5 is an example of initializing one
comparator. Comparator 1 is configured to use the CIN1A and
CMPREF inputs, outputs the comparator result to the CMP1 pin,
and generates an interrupt when the comparator output changes.
The interrupt routine used for the comparator must clear the
interrupt flag (CMF1 in this case) before returning.
SU01189
CmpInit:
mov PT0AD,#30h ; Disable digital inputs on pins that are used
; for analog functions: CIN1A, CMPREF.
anl P0M2,#0cfh ; Disable digital outputs on pins that are used
orl P0M1,#30h ; for analog functions: CIN1A, CMPREF.
mov CMP1,#24h ; Turn on comparator 1 and set up for:
; – Positive input on CIN1A.
; – Negative input from CMPREF pin.
; – Output to CMP1 pin enabled.
call delay10us ; The comparator has to start up for at
; least 10 microseconds before use.
anl CMP1,#0feh ; Clear comparator 1 interrupt flag.
setb EC1 ; Enable the comparator 1 interrupt. The
; priority is left at the current value.
setb EA ; Enable the interrupt system (if needed).
ret ; Return to caller.
Figure 5.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 11
I2C Serial Interface
The I2C bus uses two wires (SDA and SCL) to transfer information
between devices connected to the bus. The main features of the
bus are:
•Bidirectional data transfer between masters and slaves.
•Serial addressing of slaves (no added wiring).
•Acknowledgment after each transferred byte.
•Multimaster bus.
•Arbitration between simultaneously transmitting masters without
corruption of serial data on bus.
The I2C subsystem includes hardware to simplify the software required
to drive the I2C bus. The hardware is a single bit interface which in
addition to including the necessary arbitration and framing error
checks, includes clock stretching and a bus timeout timer. The
interface is synchronized to software either through polled loops
or interrupts.
Refer to the application note AN422, entitled “Using the 8XC751
Microcontroller as an I2C Bus Master” for additional discussion of
the 8xC76x I2C interface and sample driver routines.
The 87LPC764 I2C implementation duplicates that of the 87C751
and 87C752 except for the following details:
•The interrupt vector addresses for both the I2C interrupt and the
T imer I interrupt.
•The I2C SFR addresses (I2CON, !2CFG, I2DAT).
•The location of the I2C interrupt enable bit and the name of the
SFR it is located within (EI2 is Bit 0 in IEN1).
•The location of the T imer I interrupt enable bit and the name of the
SFR it is located within (ETI is Bit 7 in IEN1).
•The I2C and T imer I interrupts have a settable priority.
T imer I is used to both control the timing of the I2C bus and also to
detect a “bus locked” condition, by causing an interrupt when
nothing happens on the I2C bus for an inordinately long period of
time while a transmission is in progress. If this interrupt occurs, the
program has the opportunity to attempt to correct the fault and
resume I2C operation.
Six time spans are important in I2C operation and are insured by timer I:
•The MINIMUM HIGH time for SCL when this device is the master.
•The MINIMUM LOW time for SCL when this device is a master.
This is not very important for a single-bit hardware interface like
this one, because the SCL low time is stretched until the software
responds to the I2C flags. The software response time normally
meets or exceeds the MIN LO time. In cases where the software
responds within MIN HI + MIN LO) time, timer I will ensure that
the minimum time is met.
•The MINIMUM SCL HIGH TO SDA HIGH time in a stop condition.
•The MINIMUM SDA HIGH TO SDA LOW time between I2C stop
and start conditions (4.7ms, see I2C specification).
•The MINIMUM SDA LOW TO SCL LOW time in a start condition.
•The MAXIMUM SCL CHANGE time while an I2C frame is in
progress. A frame is in progress between a start condition and the
following stop condition. This time span serves to detect a lack of
software response on this device as well as external I2C
problems. SCL “stuck low” indicates a faulty master or slave. SCL
“stuck high” may mean a faulty device, or that noise induced onto
the I2C bus caused all masters to withdraw from I2C arbitration.
The first five of these times are 4.7 ms (see I2C specification) and
are covered by the low order three bits of timer I. T imer I is clocked
by the 87LPC764 CPU clock. T imer I can be pre-loaded with one of
four values to optimize timing for different oscillator frequencies. At
lower frequencies, software response time is increased and will
degrade maximum performance of the I2C bus. See special function
register I2CFG description for prescale values (CT0, CT1).
The MAXIMUM SCL CHANGE time is important, but its exact span
is not critical. The complete 10 bits of timer I are used to count out
the maximum time. When I2C operation is enabled, this counter is
cleared by transitions on the SCL pin. The timer does not run
between I2C frames (i.e., whenever reset or stop occurred more
recently than the last start). When this counter is running, it will carry
out after 1020 to 1023 machine cycles have elapsed since a change
on SCL. A carry out causes a hardware reset of the I2C interface
and generates an interrupt if the T imer I interrupt is enabled. In
cases where the bus hang-up is due to a lack of software response
by this device, the reset releases SCL and allows I2C operation
among other devices to continue.
T imer I is enabled to run, and will reset the I2C interface upon
overflow, if the TIRUN bit in the I2CFG register is set. The T imer I
interrupt may be enabled via the ETI bit in IEN1, and its priority set
by the PTIH and PTI bits in the Ip1H and IP1 registers respectively.
I2C Interrupts
If I2C interrupts are enabled (EA and EI2 are both set to 1), an I2C
interrupt will occur whenever the ATN flag is set by a start, stop,
arbitration loss, or data ready condition (refer to the description of ATN
following). In practice, it is not efficient to operate the I2C interface in
this fashion because the I2C interrupt service routine would somehow
have to distinguish between hundreds of possible conditions. Also,
since I2C can operate at a fairly high rate, the software may execute
faster if the code simply waits for the I2C interface.
Typically, the I 2C interrupt should only be used to indicate a start
condition at an idle slave device, or a stop condition at an idle master
device (if it is waiting to use the I2C bus). This is accomplished by
enabling the I2C interrupt only during the aforementioned conditions.
Reading I2CON
RDAT The data from SDA is captured into “Receive DATa”
whenever a rising edge occurs on SCL. RDAT is also
available (with seven low-order zeros) in the I2DAT
register. The difference between reading it here and
there is that reading I2DAT clears DRDY, allowing the
I2C to proceed on to another bit. Typically, the first
seven bits of a received byte are read from
I2DAT, while the 8th is read here. Then I2DAT can be
written to send the Acknowledge bit and clear DRDY.
A TN “ATteNtion” is 1 when one or more of DRDY, ARL, STR, or
STP is 1. Thus, ATN comprises a single bit that can be
tested to release the I2C service routine from a “wait loop.”
DRDY “Data ReaDY” (and thus ATN) is set when a rising edge
occurs on SCL, except at idle slave. DRDY is cleared
by writing CDR = 1, or by writing or reading the I2DAT
register. The following low period on SCL is stretched
until the program responds by clearing DRDY.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 12
BIT SYMBOL FUNCTION
I2CON.7 RDAT Read: the most recently received data bit.
“ CXA Write: clears the transmit active flag.
I2CON.6 ATN Read: ATN = 1 if any of the flags DRDY, ARL, STP, or STP = 1.
“ IDLE Write: in the I2C slave mode, writing a 1 to this bit causes the I2C hardware to ignore the bus until it
is needed again.
I2CON.5 DRDY Read: Data Ready flag, set when there is a rising edge on SCL.
“ CDR Write: writing a 1 to this bit clears the DRDY flag.
I2CON.4 ARL Read: Arbitration Loss flag, set when arbitration is lost while in the transmit mode.
“ CARL Write: writing a 1 to this bit clears the CARL flag.
I2CON.3 STR Read: Start flag, set when a start condition is detected at a master or non-idle slave.
“ CSTR Write: writing a 1 to this bit clears the STR flag.
I2CON.2 STP Read: Stop flag, set when a stop condition is detected at a master or non-idle slave.
“ CSTP Write: writing a 1 to this bit clears the STP flag.
I2CON.1 MASTER Read: indicates whether this device is currently as bus master .
“ XSTR Write: writing a 1 to this bit causes a repeated start condition to be generated.
I2CON.0 — Read: undefined.
“ XSTP Write: writing a 1 to this bit causes a stop condition to be generated.
* Due to the manner in which bit addressing is implemented in the 80C51 family, the I2CON register should never be altered by
use of the SETB, CLR, CPL, MOV (bit), or JBC instructions. This is due to the fact that read and write functions of this register
are different. Testing of I2CON bits via the JB and JNB instructions is supported.
—
SU01155
MASTERSTPSTRARLDRDYATNRDAT
01234567
I2CON Reset Value: 81h
Bit Addressable*
Address: D8h
XSTPXSTRCSTPCSTRCARLCDRIDLECXA
READ
WRITE
Figure 6. I2C Control Register (I2CON)
BIT SYMBOL FUNCTION
I2DAT.7 RDAT Read: the most recently received data bit, captured from SDA at every rising edge of SCL. Reading
I2DAT also clears DRDY and the Transmit Active state.
“ XDAT Write: sets the data for the next transmitted bit. Writing I2DAT also clears DRDY and sets the
T ransmit Active state.
I2DAT.6–0 – Unused.
—
SU01156
——————RDAT
01234567
I2DAT Reset Value: xxh
Not Bit Addressable
Address: D9h
———————XDAT
READ
WRITE
Figure 7. I2C Data Register (I2DAT)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 13
Checking ATN and DRDY
When a program detects ATN = 1, it should next check DRDY. If
DRDY = 1, then if it receives the last bit, it should capture the data
from RDAT (in I2DAT or I2CON). Next, if the next bit is to be sent, it
should be written to I2DAT. One way or another, it should clear
DRDY and then return to monitoring ATN. Note that if any of ARL,
STR, or STP is set, clearing DRDY will not release SCL to high, so
that the I2C will not go on to the next bit. If a program detects
ATN = 1, and DRDY = 0, it should go on to examine ARL, STR,
and STP.
ARL “Arbitration Loss” is 1 when transmit Active was set, but
this device lost arbitration to another transmitter.
T ransmit Active is cleared when ARL is 1. There are
four separate cases in which ARL is set.
1. If the program sent a 1 or repeated start, but another
device sent a 0, or a stop, so that SDA is 0 at the rising
edge of SCL. (If the other device sent a stop, the setting
of ARL will be followed shortly by STP being set.)
2. If the program sent a 1, but another device sent a
repeated start, and it drove SDA low before SCL
could be driven low. (This type of ARL is always
accompanied by STR = 1.)
3. In master mode, if the program sent a repeated start,
but another device sent a 1, and it drove SCL low
before this device could drive SDA low.
4. In master mode, if the program sent stop, but it could
not be sent because another device sent a 0.
STR “STaRt” is set to a 1 when an I2C start condition is
detected at a non-idle slave or at a master. (STR is not
set when an idle slave becomes active due to a start
bit; the slave has nothing useful to do until the rising
edge of SCL sets DRDY.)
STP “SToP” is set to 1 when an I2C stop condition is
detected at a non-idle slave or at a master. (STP is not
set for a stop condition at an idle slave.)
MASTER “MASTER” is 1 if this device is currently a master on
the I2C. MASTER is set when MASTRQ is 1 and the
bus is not busy (i.e., if a start bit hasn’t been
received since reset or a “T imer I” time-out, or if a stop
has been received since the last start). MASTER is
cleared when ARL is set, or after the software writes
MASTRQ = 0 and then XSTP = 1.
Writing I2CON
Typically, for each bit in an I2C message, a service routine waits for
ATN = 1. Based on DRDY, ARL, STR, and STP, and on the current
bit position in the message, it may then write I2CON with one or
more of the following bits, or it may read or write the I2DAT register.
CXA Writing a 1 to “Clear Xmit Active” clears the Transmit
Active state. (Reading the I2DAT register also does this.)
Regarding Transmit Active
T ransmit Active is set by writing the I2DAT register, or by writing
I2CON with XSTR = 1 or XSTP = 1. The I2C interface will only drive
the SDA line low when T ransmit Active is set, and the ARL bit will
only be set to 1 when T ransmit Active is set. Transmit Active is
cleared by reading the I2DAT register, or by writing I2CON with CXA
= 1. T ransmit Active is automatically cleared when ARL is 1.
IDLE Writing 1 to “IDLE” causes a slave’s I2C hardware to
ignore the I2C until the next start condition (but if
MASTRQ is 1, then a stop condition will cause this
device to become a master).
CDR Writing a 1 to “Clear Data Ready” clears DRDY.
(Reading or writing the I2DAT register also does this.)
CARL Writing a 1 to “Clear Arbitration Loss” clears the ARL bit.
CSTR Writing a 1 to “Clear STaRt” clears the STR bit.
CSTP Writing a 1 to “Clear SToP” clears the STP bit. Note that
if one or more of DRDY, ARL, STR, or STP is 1, the low
time of SCL is stretched until the service routine
responds by clearing them.
XSTR Writing 1s to “Xmit repeated STaRt” and CDR tells the
I2C hardware to send a repeated start condition. This
should only be at a master. Note that XSTR need not
and should not be used to send an “initial”
(non-repeated) start; it is sent automatically by the I2C
hardware. W riting XSTR = 1 includes the effect of
writing I2DAT with XDAT = 1; it sets Transmit Active
and releases SDA to high during the SCL low time.
After SCL goes high, the I2C hardware waits for the
suitable minimum time and then drives SDA low to
make the start condition.
XSTP Writing 1s to “Xmit SToP” and CDR tells the I2C
hardware to send a stop condition. This should only be
done at a master. If there are no more messages to
initiate, the service routine should clear the MASTRQ
bit in I2CFG to 0 before writing XSTP with 1. Writing
XSTP = 1 includes the effect of writing I2DAT with
XDAT = 0; it sets Transmit Active and drives SDA low
during the SCL low time. After SCL goes high, the I2C
hardware waits for the suitable minimum time and then
releases SDA to high to make the stop condition.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 14
BIT SYMBOL FUNCTION
I2CFG.7 SLAVEN Slave Enable. Writing a 1 this bit enables the slave functions of the I 2C subsystem. If SLAVEN and
MASTRQ are 0, the I2C hardware is disabled. This bit is cleared to 0 by reset and by an I2C
time-out.
I2CFG.6 MASTRQ Master Request. Writing a 1 to this bit requests mastership of the I2C bus. If a transmission is in
progress when this bit is changed from 0 to 1, action is delayed until a stop condition is detected. A
start condition is sent and DRDY is set (thus making ATN = 1 and generating an I2C interrupt).
When a master wishes to release mastership status of the I2C, it writes a 1 to XSTP in I2CON.
MASTRQ is cleared by an I2C time-out.
I2CFG.5 CLRTI W riting a 1 to this bit clears the Timer I overflow flag. This bit position always reads as a 0.
I2CFG.4 TIRUN W riting a 1 to this bit lets Timer I run; a zero stops and clears it. Together with SLAVEN, MASTRQ,
and MASTER, this bit determines operational modes as shown in Table 1.
I2CFG.2, 3 — Reserved for future use. Should not be set to 1 by user programs.
I2CFG.1, 0 CT1, CT0 These two bits are programmed as a function of the CPU clock rate, to optimize the MIN HI and LO
time of SCL when this device is a master on the I2C. The time value determined by these bits
controls both of these parameters, and also the timing for stop and start conditions.
CT0
SU01157
CT1——TIRUNCLRTIMASTRQSLAVEN
01234567
I2CFG Reset Value: 00h
Not Bit Addressable
Address: C8h
Figure 8. I2C Configuration Register (I2CFG)
Regarding Software Response Time
Because the 87LPC764 can run at 20 MHz, and because the I2C
interface is optimized for high-speed operation, it is quite likely that
an I2C service routine will sometimes respond to DRDY (which is set
at a rising edge of SCL) and write I2DAT before SCL has gone low
again. If XDAT were applied directly to SDA, this situation would
produce an I2C protocol violation. The programmer need not worry
about this possibility because XDAT is applied to SDA only when
SCL is low.
Conversely, a program that includes an I2C service routine may take
a long time to respond to DRDY. Typically, an I2C routine operates
on a flag-polling basis during a message, with interrupts from other
peripheral functions enabled. If an interrupt occurs, it will delay the
response of the I2C service routine. The programmer need not worry
about this very much either, because the I2C hardware stretches the
SCL low time until the service routine responds. The only constraint
on the response is that it must not exceed the T imer I time-out.
Values to be used in the CT1 and CT0 bits are shown in Table 2. To
allow the I2C bus to run at the maximum rate for a particular
oscillator frequency, compare the actual oscillator rate to the f OSC
max column in the table. The value for CT1 and CT0 is found in the
first line of the table where CPU clock max is greater than or equal
to the actual frequency.
Table 2 also shows the machine cycle count for various settings of
CT1/CT0. This allows calculation of the actual minimum high and
low times for SCL as follows:
SCL min highńlow time (in microseconds) +6 * Min Time Count
CPU clock (in MHz)
For instance, at an 8 MHz frequency, with CT1/CT0 set to 1 0, the
minimum SCL high and low times will be 5.25 µs.
Table 2 also shows the T imer I timeout period (given in machine
cycles) for each CT1/CT0 combination. The timeout period varies
because of the way in which minimum SCL high and low times are
measured. When the I2C interface is operating, T imer I is pre-loaded
at every SCL transition with a value dependent upon CT1/CT0. The
pre-load value is chosen such that a minimum SCL high or low time
has elapsed when T imer I reaches a count of 008 (the actual value
pre-loaded into Timer I is 8 minus the machine cycle count).
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 15
Table 1. Interaction of TIRUN with SLAVEN, MASTRQ, and MASTER
SLAVEN,
MASTRQ,
MASTER TIRUN OPERATING MODE
All 0 0The I2C interface is disabled. Timer I is cleared and does not run. This is the state assumed after a reset. If an I2C
application wants to ignore the I2C at certain times, it should write SLAVEN, MASTRQ, and TIRUN all to zero.
All 0 1The I2C interface is disabled.
Any or all 1 0The I2C interface is enabled. The 3 low-order bits of Timer I run for min-time generation, but the hi-order bits do
not, so that there is no checking for I2C being “hung.” This configuration can be used for very slow I2C operation.
Any or all 1 1The I2C interface is enabled. Timer I runs during frames on the I2C, and is cleared by transitions on SCL, and by
Start and Stop conditions. This is the normal state for I2C operation.
Table 2. CT1, CT0 Values
CT1, CT0 Min Time Count
(Machine Cycles) CPU Clock Max
(for 100 kHz I2C) Timeout Period
(Machine Cycles)
1 0 78.4 MHz 1023
0 1 67.2 MHz 1022
0 0 56.0 MHz 1021
1 1 44.8 MHz 1020
Interrupts
The 87LPC764 uses a four priority level interrupt structure. This
allows great flexibility in controlling the handling of the 87LPC764’s many
interrupt sources. The 87LPC764 supports up to 12 interrupt sources.
Each interrupt source can be individually enabled or disabled by
setting or clearing a bit in registers IEN0 or IEN1. The IEN0
register also contains a global disable bit, EA, which disables all
interrupts at once.
Each interrupt source can be individually programmed to one of four
priority levels by setting or clearing bits in the IP0, IP0H, IP1, and
IP1H registers. An interrupt service routine in progress can be
interrupted by a higher priority interrupt, but not by another interrupt
of the same or lower priority. The highest priority interrupt service
cannot be interrupted by any other interrupt source. So, if two
requests of different priority levels are received simultaneously, the
request of higher priority level is serviced.
If requests of the same priority level are received simultaneously, an
internal polling sequence determines which request is serviced. This
is called the arbitration ranking. Note that the arbitration ranking is
only used to resolve simultaneous requests of the same priority level.
Table 3 summarizes the interrupt sources, flag bits, vector
addresses, enable bits, priority bits, arbitration ranking, and whether
each interrupt may wake up the CPU from Power Down mode.
Table 3. Summary of Interrupts
Description Interrupt
Flag Bit(s) Vector
Address Interrupt
Enable Bit(s) Interrupt
Priority Arbitration
Ranking Power Down
Wakeup
External Interrupt 0 IE0 0003h EX0 (IEN0.0) IP0H.0, IP0.0 1 (highest) Yes
T imer 0 Interrupt TF0 000Bh ET0 (IEN0.1) IP0H.1, IP0.1 4 No
External Interrupt 1 IE1 0013h EX1 (IEN0.2) IP0H.2, IP0.2 7Yes
T imer 1 Interrupt TF1 001Bh ET1 (IEN0.3) IP0H.3, IP0.3 10 No
Serial Port Tx and Rx TI & RI 0023h ES (IEN0.4) IP0H.4, IP0.4 12 No
Brownout Detect BOD 002Bh EBO (IEN0.5) IP0H.5, IP0.5 2Yes
I2C Interrupt ATN 0033h EI2 (IEN1.0) IP1H.0, IP1.0 5 No
KBI Interrupt KBF 003Bh EKB (IEN1.1) IP1H.1, IP1.1 8Yes
Comparator 2 interrupt CMF2 0043h EC2 (IEN1.2) IP1H.2, IP1.2 11 Yes
W atchdog Timer WDOVF 0053h EWD (IEN0.6) IP0H.6, IP0.6 3Yes
Comparator 1 interrupt CMF1 0063h EC1 (IEN1.5) IP1H.5, IP1.5 9Yes
T imer I interrupt – 0073h ETI (IEN1.7) IP1H.7, IP1.7 13 (lowest) No
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 16
External Interrupt Inputs
The 87LPC764 has two individual interrupt inputs as well as the
Keyboard Interrupt function. The latter is described separately
elsewhere in this section. The two interrupt inputs are identical to
those present on the standard 80C51 microcontroller.
The external sources can be programmed to be level-activated or
transition-activated by setting or clearing bit IT1 or IT0 in Register
TCON. If ITn = 0, external interrupt n is triggered by a detected low
at the INTn pin. If ITn = 1, external interrupt n is edge triggered. In
this mode if successive samples of the INTn pin show a high in one
cycle and a low in the next cycle, interrupt request flag IEn in TCON
is set, causing an interrupt request.
Since the external interrupt pins are sampled once each machine
cycle, an input high or low should hold for at least 6 CPU Clocks to
ensure proper sampling. If the external interrupt is
transition-activated, the external source has to hold the request pin
high for at least one machine cycle, and then hold it low for at least
one machine cycle. This is to ensure that the transition is seen and
that interrupt request flag IEn is set. IEn is automatically cleared by
the CPU when the service routine is called.
If the external interrupt is level-activated, the external source must
hold the request active until the requested interrupt is actually
generated. If the external interrupt is still asserted when the interrupt
service routine is completed another interrupt will be generated. It is
not necessary to clear the interrupt flag IEn when the interrupt is
level sensitive, it simply tracks the input pin level.
If an external interrupt is enabled when the 87LPC764 is put into
Power Down or Idle mode, the interrupt will cause the processor to
wake up and resume operation. Refer to the section on Power
Reduction Modes for details.
SU01158
WAKEUP
(IF IN POWER
DOWN)
EA
(FROM IEN0
REGISTER) INTERRUPT
TO CPU
IE0
EX0
IE1
EX1
BOD
EBO
KBF
EKB
CM2
EC2
WDT
EWD
CM1
EC1
TF0
ET0
TF1
ET1
RI + TI
ES
ATN
EI2
Figure 9. Interrupt Sources, Interrupt Enables, and Power Down Wakeup Sources
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 17
I/O Ports
The 87LPC764 has 3 I/O ports, port 0, port 1, and port 2. The exact
number of I/O pins available depend upon the oscillator and reset
options chosen. At least 15 pins of the 87LPC764 may be used as
I/Os when a two-pin external oscillator and an external reset circuit
are used. Up to 18 pins may be available if fully on-chip oscillator
and reset configurations are chosen.
All but three I/O port pins on the 87LPC764 may be software
configured to one of four types on a bit-by-bit basis, as shown in
Table 4. These are: quasi-bidirectional (standard 80C51 port
outputs), push-pull, open drain, and input only. Two configuration
registers for each port choose the output type for each port pin.
Table 4. Port Output Configuration Settings
PxM1.y PxM2.y Port Output Mode
0 0 Quasi-bidirectional
0 1 Push-Pull
1 0 Input Only (High Impedance)
1 1 Open Drain
Quasi-Bidirectional Output Configuration
The default port output configuration for standard 87LPC764 I/O
ports is the quasi-bidirectional output that is common on the 80C51
and most of its derivatives. This output type can be used as both an
input and output without the need to reconfigure the port. This is
possible because when the port outputs a logic high, it is weakly
driven, allowing an external device to pull the pin low. When the pin
is pulled low, it is driven strongly and able to sink a fairly large
current. These features are somewhat similar to an open drain
output except that there are three pull-up transistors in the
quasi-bidirectional output that serve different purposes.
One of these pull-ups, called the “very weak” pull-up, is turned on
whenever the port latch for the pin contains a logic 1. The very weak
pull-up sources a very small current that will pull the pin high if it is
left floating.
A second pull-up, called the “weak” pull-up, is turned on when the
port latch for the pin contains a logic 1 and the pin itself is also at a
logic 1 level. This pull-up provides the primary source current for a
quasi-bidirectional pin that is outputting a 1. If a pin that has a logic 1
on it is pulled low by an external device, the weak pull-up turns off,
and only the very weak pull-up remains on. In order to pull the pin
low under these conditions, the external device has to sink enough
current to overpower the weak pull-up and take the voltage on the
port pin below its input threshold.
The third pull-up is referred to as the “strong” pull-up. This pull-up is
used to speed up low-to-high transitions on a quasi-bidirectional port
pin when the port latch changes from a logic 0 to a logic 1. When this
occurs, the strong pull-up turns on for a brief time, two CPU clocks, in
order to pull the port pin high quickly. Then it turns of f again.
The quasi-bidirectional port configuration is shown in Figure 10.
SU01159
WEAK
VERY
WEAK
STRONG
PORT
PIN
VDD
2 CPU
CLOCK DELAY
INPUT
DATA
PORT LATCH
DATA N
PPP
Figure 10. Quasi-Bidirectional Output
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 18
Open Drain Output Configuration
The open drain output configuration turns off all pull-ups and only
drives the pull-down transistor of the port driver when the port latch
contains a logic 0. To be used as a logic output, a port configured in
this manner must have an external pull-up, typically a resistor tied to
VDD. The pull-down for this mode is the same as for the
quasi-bidirectional mode.
The open drain port configuration is shown in Figure 11.
Push-Pull Output Configuration
The push-pull output configuration has the same pull-down structure
as both the open drain and the quasi-bidirectional output modes, but
provides a continuous strong pull-up when the port latch contains a
logic 1. The push-pull mode may be used when more source current
is needed from a port output.
The push-pull port configuration is shown in Figure 12.
The three port pins that cannot be configured are P1.2, P1.3, and
P1.5. The port pins P1.2 and P1.3 are permanently configured as
open drain outputs. They may be used as inputs by writing ones to
their respective port latches. P1.5 may be used as a Schmitt trigger
input if the 87LPC764 has been configured for an internal reset and
is not using the external reset input function RST.
Additionally, port pins P2.0 and P2.1 are disabled for both input and
output if one of the crystal oscillator options is chosen. Those
options are described in the Oscillator section.
The value of port pins at reset is determined by the PRHI bit in the
UCFG1 register. Ports may be configured to reset high or low as
needed for the application. When port pins are driven high at reset,
they are in quasi-bidirectional mode and therefore do not source
large amounts of current.
Every output on the 87LPC764 may potentially be used as a 20 mA
sink LED drive output. However, there is a maximum total output
current for all ports which must not be exceeded.
All ports pins of the 87LPC764 have slew rate controlled outputs. This
is to limit noise generated by quickly switching output signals. The
slew rate is factory set to approximately 10 ns rise and fall times.
The bits in the P2M1 register that are not used to control
configuration of P2.1 and P2.0 are used for other purposes. These
bits can enable Schmitt trigger inputs on each I/O port, enable
toggle outputs from T imer 0 and Timer 1, and enable a clock output
if either the internal RC oscillator or external clock input is being
used. The last two functions are described in the T imer/Counters
and Oscillator sections respectively. The enable bits for all of these
functions are shown in Figure 13.
Each I/O port of the 87LPC764 may be selected to use TTL level
inputs or Schmitt inputs with hysteresis. A single configuration bit
determines this selection for the entire port. Port pins P1.2, P1.3,
and P1.5 always have a Schmitt trigger input.
SU01160
PORT
PIN
INPUT
DATA
PORT LATCH
DATA N
Figure 11. Open Drain Output
SU01161
PORT
PIN
VDD
INPUT
DATA
PORT LATCH
DATA N
P
Figure 12. Push-Pull Output
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 19
BIT SYMBOL FUNCTION
P2M1.7 P2S When P2S = 1, this bit enables Schmitt trigger inputs on Port 2.
P2M1.6 P1S When P1S = 1, this bit enables Schmitt trigger inputs on Port 1.
P2M1.5 P0S When P0S = 1, this bit enables Schmitt trigger inputs on Port 0.
P2M1.4 ENCLK When ENCLK is set and the 87LPC764 is configured to use the on-chip RC oscillator, a clock
output is enabled on the X2 pin (P2.0). Refer to the Oscillator section for details.
P2M1.3 ENT1 When set, the P.7 pin is toggled whenever Timer 1 overflows. The output frequency is therefore
one half of the T imer 1 overflow rate. Refer to the Timer/Counters section for details.
P2M1.2 ENT0 When set, the P1.2 pin is toggled whenever Timer 0 overflows. The output frequency is therefore
one half of the T imer 0 overflow rate. Refer to the Timer/Counterssection for details.
P2M1.1, P2M1.0 — These bits, along with the matching bits in the P2M2 register, control the output configuration of
P2.1 and P2.0 respectively, as shown in Table 4.
(P2M1.0)
SU01162
(P2M1.1)ENT0ENT1ENCLKP0SP1SP2S
01234567
P2M1 Reset Value: 00h
Not Bit Addressable
Address: A4h
Figure 13. Port 2 Mode Register 1 (P2M1)
Keyboard Interrupt (KBI)
The Keyboard Interrupt function is intended primarily to allow a
single interrupt to be generated when any key is pressed on a
keyboard or keypad connected to specific pins of the 87LPC764, as
shown in Figure 14. This interrupt may be used to wake up the CPU
from Idle or Power Down modes. This feature is particularly useful in
handheld, battery powered systems that need to carefully manage
power consumption yet also need to be convenient to use.
The 87LPC764 allows any or all pins of port 0 to be enabled to
cause this interrupt. Port pins are enabled by the setting of bits in
the KBI register, as shown in Figure 15. The Keyboard Interrupt Flag
(KBF) in the AUXR1 register is set when any enabled pin is pulled
low while the KBI interrupt function is active. An interrupt will
generated if it has been enabled. Note that the KBF bit must be
cleared by software.
Due to human time scales and the mechanical delay associated with
keyswitch closures, the KBI feature will typically allow the interrupt
service routine to poll port 0 in order to determine which key was
pressed, even if the processor has to wake up from Power Down
mode. Refer to the section on Power Reduction Modes for details.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 20
SU01163
KBF (KBI INTERRUPT)
EKB
(FROM IEN1 REGISTER)
P0.7
KBI.7
P0.6
KBI.6
P0.5
P0.4
P0.3
P0.2
P0.1
P0.0
KBI.5
KBI.4
KBI.3
KBI.2
KBI.1
KBI.0
Figure 14. Keyboard Interrupt
BIT SYMBOL FUNCTION
KBI.7 — When set, enables P0.7 as a cause of a Keyboard Interrupt.
KBI.6 — When set, enables P0.6 as a cause of a Keyboard Interrupt.
KBI.5 — When set, enables P0.5 as a cause of a Keyboard Interrupt.
KBI.4 — When set, enables P0.4 as a cause of a Keyboard Interrupt.
KBI.3 — When set, enables P0.3 as a cause of a Keyboard Interrupt.
KBI.2 — When set, enables P0.2 as a cause of a Keyboard Interrupt.
KBI.1 — When set, enables P0.1 as a cause of a Keyboard Interrupt.
KBI.0 — When set, enables P0.0 as a cause of a Keyboard Interrupt.
Note: the Keyboard Interrupt must be enabled in order for the settings of the KBI register to be effective. The interrupt flag
(KBF) is located at bit 7 of AUXR1.
KBI.0
SU01164
KBI.1KBI.2KBI.3KBI.4KBI.5KBI.6KBI.7
01234567
KBI Reset Value: 00h
Not Bit Addressable
Address: 86h
Figure 15. Keyboard Interrupt Register (KBI)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 21
Oscillator
The 87LPC764 provides several user selectable oscillator options,
allowing optimization for a range of needs from high precision to
lowest possible cost. These are configured when the EPROM is
programmed. Basic oscillator types that are supported include: low,
medium, and high speed crystals, covering a range from 20 kHz to
20 MHz; ceramic resonators; and on-chip RC oscillator.
Low Frequency Oscillator Option
This option supports an external crystal in the range of 20 kHz to 100 kHz.
Table 5 shows capacitor values that may be used with a quartz crystal in this mode.
Table 5. Recommended oscillator capacitors for use with the low frequency oscillator option
Oscillator VDD = 2.7 to 4.5 V VDD = 4.5 to 6.0 V
Frequency Lower Limit Optimal Value Upper Limit Lower Limit Optimal Value Upper Limit
20 kHz 15 pF 15 pF 33 pF 33 pF 33 pF 47 pF
32 kHz 15 pF 15 pF 33 pF 33 pF 33 pF 47 pF
100 kHz 15 pF 15 pF 33 pF 15 pF 15 pF 33 pF
Medium Frequency Oscillator Option
This option supports an external crystal in the range of 100 kHz to 4 MHz. Ceramic resonators are also supported in this configuration.
Table 6 shows capacitor values that may be used with a quartz crystal in this mode.
Table 6. Recommended oscillator capacitors for use with the medium frequency oscillator option
Oscillator Freq ency
VDD = 2.7 to 4.5 V
Oscillator
Freq
u
ency
Lower Limit Optimal Value Upper Limit
100 kHz 33 pF 33 pF 47 pF
1 MHz 15 pF 15 pF 33 pF
4 MHz 15 pF 15 pF 33 pF
High Frequency Oscillator Option
This option supports an external crystal in the range of 4 to 20 MHz. Ceramic resonators are also supported in this configuration.
Table 7 shows capacitor values that may be used with a quartz crystal in this mode.
Table 7. Recommended oscillator capacitors for use with the high frequency oscillator option
Oscillator VDD = 2.7 to 4.5 V VDD = 4.5 to 6.0 V
Frequency Lower Limit Optimal Value Upper Limit Lower Limit Optimal Value Upper Limit
4 MHz 15 pF 33 pF 47 pF 15 pF 33 pF 68 pF
8 MHz 15 pF 15 pF 33 pF 15 pF 33 pF 47 pF
16 MHz – – – 15 pF 15 pF 33 pF
20 MHz – – – 15 pF 15 pF 33 pF
On-Chip RC Oscillator Option
The on-chip RC oscillator option has a typical frequency of 6 MHz
and can be divided down for slower operation through the use of the
DIVM register. Note that the on-chip oscillator has a ±25% frequency
tolerance and for that reason may not be suitable for use in some
applications. A clock output on the X2/P2.0 pin may be enabled
when the on-chip RC oscillator is used.
External Clock Input Option
In this configuration, the processor clock is input from an external
source driving the X1/P2.1 pin. The rate may be from 0 Hz up to
20 MHz when VDD is above 4.5 V and up to 10 MHz when VDD is
below 4.5 V. When the external clock input mode is used, the X2/P2.0
pin may be used as a standard port pin. A clock output on the X2/P2.0
pin may be enabled when the external clock input is used.
Clock Output
The 87LPC764 supports a clock output function when either the
on-chip RC oscillator or external clock input options are selected.
This allows external devices to synchronize to the 87LPC764. When
enabled, via the ENCLK bit in the P2M1 register, the clock output
appears on the X2/CLKOUT pin whenever the on-chip oscillator is
running, including in Idle mode. The frequency of the clock output is
1/6 of the CPU clock rate. If the clock output is not needed in Idle
mode, it may be turned off prior to entering Idle, saving additional
power. The clock output may also be enabled when the external
clock input option is selected.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 22
SU01165
87LPC764
QUARTZ CRYSTAL OR
CERAMIC RESONATOR
X2
X1
THE OSCILLATOR MUST BE CONFIGURED IN ONE OF
THE FOLLOWING MODES:
– LOW FREQUENCY CRYSTAL
– MEDIUM FREQUENCY CRYSTAL
– HIGH FREQUENCY CRYSTAL
*
CAPACITOR VALUES MAY BE OPTIMIZED FOR
DIFFERENT OSCILLATOR FREQUENCIES (SEE TEXT)
A SERIES RESISTOR MAY BE REQUIRED IN ORDER TO
LIMIT CRYSTAL DRIVE LEVELS. THIS IS PARTICULARLY
IMPORTANT FOR LOW FREQUENCY CRYSTALS (SEE TEXT).
Figure 16. Using the Crystal Oscillator
SU01166
87LPC764
X2
X1
THE OSCILLATOR MUST BE CONFIGURED IN
THE EXTERNAL CLOCK INPUT MODE.
A CLOCK OUTPUT MAY BE OBTAINED ON
THE X2 PIN BY SETTING THE ENCLK BIT IN
THE P2M1 REGISTER.
CMOS COMPATIBLE EXTERNAL
OSCILLATOR SIGNAL
Figure 17. Using an External Clock Input
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 23
SU01167
CLOCK SELECT
CLOCK
SOURCES
CLOCK
OUT
XTAL
SELECT
INTERNAL RC OSCILLATOR
CRYSTAL: LOW FREQUENCY
CRYSTAL: MEDIUM FREQUENCY
CRYSTAL: HIGH FREQUENCY
EXTERNAL CLOCK INPUT
10-BIT RIPPLE COUNTER
RESET
COUNT
COUNT 256
COUNT 1024
OSCILLATOR STARTUP TIMER
DIVIDE-BY-M
(DIVM REGISTER)
AND
CLKR SELECT CPU
CLOCK
÷1/÷2
CLKR
(UCFG1.3)
POWER DOWN
POWER MONITOR RESET
FOSC0 (UCFG1.0)
FOSC1 (UCFG1.1)
FOSC2 (UCFG1.2)
Figure 18. Block Diagram of Oscillator Control
CPU Clock Modification: CLKR and DIVM
For backward compatibility, the CLKR configuration bit allows
setting the 87LPC764 instruction and peripheral timing to match
standard 80C51 timing by dividing the CPU clock by two. Default
timing for the 87LPC764 is 6 CPU clocks per machine cycle while
standard 80C51 timing is 12 clocks per machine cycle. This
division also applies to peripheral timing, allowing 80C51 code that
is oscillator frequency and/or timer rate dependent. The CLKR bit
is located in the EPROM configuration register UCFG1, described
under EPROM Characteristics
In addition to this, the CPU clock may be divided down from the
oscillator rate by a programmable divider, under program control.
This function is controlled by the DIVM register. If the DIVM register
is set to zero (the default value), the CPU will be clocked by either
the unmodified oscillator rate, or that rate divided by two, as
determined by the previously described CLKR function.
When the DIVM register is set to some value N (between 1 and 255),
the CPU clock is divided by 2 * (N + 1). Clock division values from 4
through 512 are thus possible. This feature makes it possible to
temporarily run the CPU at a lower rate, reducing power consumption,
in a manner similar to Idle mode. By dividing the clock, the CPU can
retain the ability to respond to events other than those that can cause
interrupts (i.e. events that allow exiting the Idle mode) by executing its
normal program at a lower rate. This can allow bypassing the
oscillator startup time in cases where Power Down mode would
otherwise be used. The value of DIVM may be changed by the
program at any time without interrupting code execution.
Power Monitoring Functions
The 87LPC764 incorporates power monitoring functions designed to
prevent incorrect operation during initial power up and power loss or
reduction during operation. This is accomplished with two hardware
functions: Power-On Detect and Brownout Detect.
Brownout Detection
The Brownout Detect function allows preventing the processor from
failing in an unpredictable manner if the power supply voltage drops
below a certain level. The default operation is for a brownout
detection to cause a processor reset, however it may alternatively
be configured to generate an interrupt by setting the BOI bit in the
AUXR1 register (AUXR1.5).
The 87LPC764 allows selection of two Brownout levels: 2.5 V or
3.8 V. When VDD drops below the selected voltage, the brownout
detector triggers and remains active until VDD is returns to a level
above the Brownout Detect voltage. When Brownout Detect causes
a processor reset, that reset remains active as long as VDD remains
below the Brownout Detect voltage. When Brownout Detect
generates an interrupt, that interrupt occurs once as VDD crosses
from above to below the Brownout Detect voltage. For the interrupt
to be processed, the interrupt system and the BOI interrupt must
both be enabled (via the EA and EBO bits in IEN0).
When Brownout Detect is activated, the BOF flag in the PCON
register is set so that the cause of processor reset may be determined
by software. This flag will remain set until cleared by software.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 24
For correct activation of Brownout Detect, the VDD fall time must be
no faster than 50 mV/µs. When VDD is restored, is should not rise
faster than 2 mV/µs in order to insure a proper reset.
The brownout voltage (2.5 V or 3.8 V) is selected via the BOV bit in
the EPROM configuration register UCFG1. When unprogrammed
(BOV = 1), the brownout detect voltage is 2.5 V. When programmed
(BOV = 0), the brownout detect voltage is 3.8 V.
If the Brownout Detect function is not required in an application, it
may be disabled, thus saving power. Brownout Detect is disabled by
setting the control bit BOD in the AUXR1 register (AUXR1.6).
Power On Detection
The Power On Detect has a function similar to the Brownout Detect,
but is designed to work as power comes up initially, before the
power supply voltage reaches a level where Brownout Detect can
work. When this feature is activated, the POF flag in the PCON
register is set to indicate an initial power up condition. The POF flag
will remain set until cleared by software.
Power Reduction Modes
The 87LPC764 supports Idle and Power Down modes of power
reduction.
Idle Mode
The Idle mode leaves peripherals running in order to allow them to
activate the processor when an interrupt is generated. Any enabled
interrupt source or Reset may terminate Idle mode. Idle mode is
entered by setting the IDL bit in the PCON register (see Figure 19).
Power Down Mode
The Power Down mode stops the oscillator in order to absolutely
minimize power consumption. Power Down mode is entered by
setting the PD bit in the PCON register (see Figure 19).
The processor can be made to exit Power Down mode via Reset or
one of the interrupt sources shown in Table 5. This will occur if the
interrupt is enabled and its priority is higher than any interrupt
currently in progress.
In Power Down mode, the power supply voltage may be reduced to
the RAM keep-alive voltage VRAM. This retains the RAM contents
at the point where Power Down mode was entered. SFR contents
are not guaranteed after VDD has been lowered to VRAM, therefore
it is recommended to wake up the processor via Reset in this case.
VDD must be raised to within the operating range before the Power
Down mode is exited. Since the watchdog timer has a separate
oscillator, it may reset the processor upon overflow if it is running
during Power Down.
Note that if the Brownout Detect reset is enabled, the processor will
be put into reset as soon as VDD drops below the brownout voltage.
If Brownout Detect is configured as an interrupt and is enabled, it will
wake up the processor from Power Down mode when VDD drops
below the brownout voltage.
When the processor wakes up from Power Down mode, it will start
the oscillator immediately and begin execution when the oscillator is
stable. Oscillator stability is determined by counting 1024 CPU
clocks after start-up when one of the crystal oscillator configurations
is used, or 256 clocks after start-up for the internal RC or external
clock input configurations.
Some chip functions continue to operate and draw power during
Power Down mode, increasing the total power used during Power
Down. These include the Brownout Detect, W atchdog Timer, and
Comparators.
BIT SYMBOL FUNCTION
PCON.7 SMOD1 When set, this bit doubles the UART baud rate for modes 1, 2, and 3.
PCON.6 SMOD0 This bit selects the function of bit 7 of the SCON SFR. When 0, SCON.7 is the SM0 bit. When 1,
SCON.7 is the FE (Framing Error) flag. See Figure 26 for additional information.
PCON.5 BOF Brown Out Flag. Set automatically when a brownout reset or interrupt has occurred. Also set at
power on. Cleared by software. Refer to the Power Monitoring Functions section for additional
information.
PCON.4 POF Power On Flag. Set automatically when a power-on reset has occurred. Cleared by software. Refer
to the Power Monitoring Functions section for additional information.
PCON.3 GF1 General purpose flag 1. May be read or written by user software, but has no effect on operation.
PCON.2 GF0 General purpose flag 0. May be read or written by user software, but has no effect on operation.
PCON.1 PD Power Down control bit. Setting this bit activates Power Down mode operation. Cleared when the
Power Down mode is terminated (see text).
PCON.0 IDL Idle mode control bit. Setting this bit activates Idle mode operation. Cleared when the Idle mode is
terminated (see text).
IDL
SU01168
PDGF0GF1POFBOFSMOD0SMOD1
01234567
PCON Reset Value: S 30h for a Power On reset
S 20h for a Brownout reset
S 00h for other reset sources
Not Bit Addressable
Address: 87h
Figure 19. Power Control Register (PCON)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 25
Table 8. Sources of Wakeup from Power Down Mode
W akeup Source Conditions
External Interrupt 0 or 1 The corresponding interrupt must be enabled.
Keyboard Interrupt The keyboard interrupt feature must be enabled and properly set up. The corresponding interrupt must be
enabled.
Comparator 1 or 2 The comparator(s) must be enabled and properly set up. The corresponding interrupt must be enabled.
W atchdog Timer Reset The watchdog timer must be enabled via the WDTE bit in the UCFG1 EPROM configuration byte.
W atchdog Timer Interrupt The WDTE bit in the UCFG1 EPROM configuration byte must not be set. The corresponding interrupt must
be enabled.
Brownout Detect Reset The BOD bit in AUXR1 must not be set (brownout detect not disabled). The BOI bit in AUXR1 must not be
set (brownout interrupt disabled).
Brownout Detect Interrupt The BOD bit in AUXR1 must not be set (brownout detect not disabled). The BOI bit in AUXR1 must be set
(brownout interrupt enabled). The corresponding interrupt must be enabled.
Reset Input The external reset input must be enabled.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 26
Low Voltage EPROM Operation
The EPROM array contains some analog circuits that are not
required when VDD is less than 4 V, but are required for a VDD
greater than 4 V. The LPEP bit (AUXR.4), when set by software, will
power down these analog circuits resulting in a reduced supply
current. LPEP is cleared only by power-on reset, so it may be set
ONLY for applications that always operate with VDD less than 4 V.
Reset
The 87LPC764 has an active low reset input when configured for an
external reset. A fully internal reset may also be configured which
provides a reset when power is initially applied to the device. The
watchdog timer can act as an oscillator fail detect because it uses
an independent, fully on-chip oscillator.
The external reset input is disabled, and fully internal reset
generation enabled, by programming the RPD bit in the EPROM
configuration register UCFG1 to 0. EPROM configuration is
described in the section EPROM Characteristics
SU01169
87LPC764 87LPC764
VDD
8.2 kW
10 mF
RST
RST
2.2 mF
Figure 20. Typical External Reset Circuits
SU01170
CHIP RESET
CPU
CLOCK
Q
RESET
TIMING
RPD (UCFG1.6)
WDT
MODULE
SOFTWARE RESET
SRST (AUXR1.3)
POWER MONITOR
RESET
RST/VPP PIN
WDTE (UCFG1.7)
S
R
Figure 21. Block Diagram Showing Reset Sources
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 27
Timer/Counters
The 87LPC764 has two general purpose counter/timers which are
upward compatible with the standard 80C51 T imer 0 and Timer 1.
Both can be configured to operate either as timers or event counters
(see Figure 22). An option to automatically toggle the T0 and/or T1
pins upon timer overflow has been added.
In the “T imer” function, the register is incremented every machine
cycle. Thus, one can think of it as counting machine cycles. Since a
machine cycle consists of 6 CPU clock periods, the count rate is 1/6
of the CPU clock frequency. Refer to the section Enhanced CPU for
a description of the CPU clock.
In the “Counter” function, the register is incremented in response to
a 1-to-0 transition at its corresponding external input pin, T0 or T1.
In this function, the external input is sampled once during every
machine cycle. When the samples of the pin state show a high in
one cycle and a low in the next cycle, the count is incremented. The
new count value appears in the register during the cycle following
the one in which the transition was detected. Since it takes 2
machine cycles (12 CPU clocks) to recognize a 1-to-0 transition, the
maximum count rate is 1/6 of the CPU clock frequency. There are no
restrictions on the duty cycle of the external input signal, but to
ensure that a given level is sampled at least once before it changes,
it should be held for at least one full machine cycle.
The “T imer” or “Counter” function is selected by control bits C/T in
the Special Function Register TMOD. In addition to the “T imer” or
“Counter” selection, T imer 0 and Timer 1 have four operating
modes, which are selected by bit-pairs (M1, M0) in TMOD. Modes 0,
1, and 2 are the same for both T imers/Counters. Mode 3 is different.
The four operating modes are described in the following text.
BIT SYMBOL FUNCTION
TMOD.7 GA TE Gating control for Timer 1. When set, Timer/Counter is enabled only while the INT1 pin is high and
the TR1 control pin is set. When cleared, T imer 1 is enabled when the TR1 control bit is set.
TMOD.6 C/T Timer or Counter Selector for Timer 1. Cleared for Timer operation (input from internal system clock.)
Set for Counter operation (input from T1 input pin).
TMOD.5, 4 M1, M0 Mode Select for Timer 1 (see table below).
TMOD.3 GA TE Gating control for Timer 0. When set, Timer/Counter is enabled only while the INT0 pin is high and
the TR0 control pin is set. When cleared, T imer 0 is enabled when the TR0 control bit is set.
TMOD.2 C/T Timer or Counter Selector for Timer 0. Cleared for Timer operation (input from internal system clock.)
Set for Counter operation (input from T0 input pin).
TMOD.1, 0 M1, M0 Mode Select for Timer 0 (see table below).
M1, M0 T imer Mode
0 0 8048 T imer “TLn” serves as 5-bit prescaler.
0 1 16-bit T imer/Counter “THn” and “TLn” are cascaded; there is no prescaler.
1 0 8-bit auto-reload Timer/Counter. THn holds a value which is loaded into TLn when it overflows.
1 1 T imer 0 is a dual 8-bit Timer/Counter in this mode. TL0 is an 8-bit Timer/Counter controlled by the
standard Timer 0 control bits. TH0 is an 8-bit timer only, controlled by the Timer 1 control bits (see
text). T imer 1 in this mode is stopped.
M0
SU01171
M1C/TGATEM0M1C/TGATE
01234567
TMOD Reset Value: 00h
Not Bit Addressable
Address: 89h
Figure 22. Timer/Counter Mode Control Register (TMOD)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 28
Mode 0
Putting either Timer into Mode 0 makes it look like an 8048 Timer,
which is an 8-bit Counter with a divide-by-32 prescaler. Figure 24
shows Mode 0 operation.
In this mode, the T imer register is configured as a 13-bit register. As
the count rolls over from all 1s to all 0s, it sets the T imer interrupt
flag TFn. The count input is enabled to the T imer when TRn = 1 and
either GATE = 0 or INTn = 1. (Setting GATE = 1 allows the Timer to
be controlled by external input INTn, to facilitate pulse width
measurements). TRn is a control bit in the Special Function Register
TCON (Figure 23). The GATE bit is in the TMOD register.
The 13-bit register consists of all 8 bits of THn and the lower 5 bits
of TLn. The upper 3 bits of TLn are indeterminate and should be
ignored. Setting the run flag (TRn) does not clear the registers.
Mode 0 operation is the same for T imer 0 and Timer 1. See
Figure 24. There are two different GATE bits, one for Timer 1
(TMOD.7) and one for T imer 0 (TMOD.3).
BIT SYMBOL FUNCTION
TCON.7 TF1 Timer 1 overflow flag. Set by hardware on Timer/Counter overflow. Cleared by hardware when the
interrupt is processed, or by software.
TCON.6 TR1 Timer 1 Run control bit. Set/cleared by software to turn Timer/Counter 1 on/off.
TCON.5 TF0 Timer 0 overflow flag. Set by hardware on Timer/Counter overflow. Cleared by hardware when the
processor vectors to the interrupt routine, or by software.
TCON.4 TR0 Timer 0 Run control bit. Set/cleared by software to turn Timer/Counter 0 on/off.
TCON.3 IE1 Interrupt 1 Edge flag. Set by hardware when external interrupt 1 edge is detected. Cleared by
hardware when the interrupt is processed, or by software.
TCON.2 IT1 Interrupt 1 Type control bit. Set/cleared by software to specify falling edge/low level triggered
external interrupts.
TCON.1 IE0 Interrupt 0 Edge flag. Set by hardware when external interrupt 0 edge is detected. Cleared by
hardware when the interrupt is processed, or by software.
TCON.0 IT0 Interrupt 0 Type control bit. Set/cleared by software to specify falling edge/low level triggered
external interrupts.
IT0
SU01172
IE0IT1IE1TR0TF0TR1TF1
01234567
TCON Reset Value: 00h
Bit Addressable
Address: 88h
Figure 23. Timer/Counter Control Register (TCON)
SU01173
TLN
(5-BITS) THN
(8-BITS)
OSC/6 OR
OSC/12
OVERFLOW
Tn PIN
TnOE
TOGGLE
CONTROL
C/T = 1
C/T = 0
Tn PIN
TRn
GATE
INTn PIN
INTERRUPT
TFn
Figure 24. Timer/Counter 0 or 1 in Mode 0 (13-Bit Counter)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 29
Mode 1
Mode 1 is the same as Mode 0, except that all 16 bits of the timer
register (THn and TLn) are used. See Figure 25
Mode 2
Mode 2 configures the T imer register as an 8-bit Counter (TL1) with
automatic reload, as shown in Figure 26. Overflow from TLn not only
sets TFn, but also reloads TLn with the contents of THn, which must
be preset by software. The reload leaves THn unchanged. Mode 2
operation is the same for T imer 0 and Timer 1.
Mode 3
When Timer 1 is in Mode 3 it is stopped. The effect is the same as
setting TR1 = 0.
T imer 0 in Mode 3 establishes TL0 and TH0 as two separate 8-bit
counters. The logic for Mode 3 on T imer 0 is shown in Figure 27.
TL0 uses the T imer 0 control bits: C/T, GATE, TR0, INT0, and TF0.
TH0 is locked into a timer function (counting machine cycles) and
takes over the use of TR1 and TF1 from T imer 1. Thus, TH0 now
controls the “T imer 1” interrupt.
Mode 3 is provided for applications that require an extra 8-bit timer.
With T imer 0 in Mode 3, an 87LPC764 can look like it has three
T imer/Counters. When Timer 0 is in Mode 3, T imer 1 can be turned
on and off by switching it into and out of its own Mode 3. It can still
be used by the serial port as a baud rate generator, or in any
application not requiring an interrupt.
SU01174
TLN
(8-BITS) THN
(8-BITS)
OSC/6 OR
OSC/12
OVERFLOW
Tn PIN
TnOE
TOGGLE
CONTROL
C/T = 1
C/T = 0
Tn PIN
TRn
GATE
INTn PIN
INTERRUPT
TFn
Figure 25. Timer/Counter 0 or 1 in Mode 1 (16-Bit Counter)
SU01392
TLN
(8-BITS)
THN
(8-BITS)
OSC/6 OR
OSC/12 OVERFLOW
Tn PIN
TnOE
TOGGLE
CONTROL
C/T = 1
C/T = 0
Tn PIN
TRn
GATE
INTn PIN
INTERRUPT
TFn
RELOAD
Figure 26. Timer/Counter 0 or 1 in Mode 2 (8-Bit Auto-Reload)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 30
SU01176
TL0
(8-BITS)
OSC/6 OR
OSC/12 OVERFLOW
T0 PIN
T0OE
TOGGLE
CONTROL
C/T = 1
C/T = 0
T0 PIN
TR0
GATE
INT0 PIN
INTERRUPT
TF0
TH0
(8-BITS) OVERFLOW
T1 PIN
T1OE
TOGGLE
CONTROL
INTERRUPT
TF1
TR1
OSC/6 OR
OSC/12
Figure 27. Timer/Counter 0 Mode 3 (Two 8-Bit Counters)
Timer Overflow Toggle Output
T imers 0 and 1 can be configured to automatically toggle a port
output whenever a timer overflow occurs. The same device pins that
are used for the T0 and T1 count inputs are also used for the timer
toggle outputs. This function is enabled by control bits T0OE and
T1OE in the P2M1 register, and apply to Timer 0 and Timer 1
respectively. The port outputs will be a logic 1 prior to the first timer
overflow when this mode is turned on.
UART
The 87LPC764 includes an enhanced 80C51 UART. The baud rate
source for the UART is timer 1 for modes 1 and 3, while the rate is
fixed in modes 0 and 2. Because CPU clocking is different on the
87LPC764 than on the standard 80C51, baud rate calculation is
somewhat different. Enhancements over the standard 80C51 UART
include Framing Error detection and automatic address recognition.
The serial port is full duplex, meaning it can transmit and receive
simultaneously. It is also receive-buffered, meaning it can
commence reception of a second byte before a previously received
byte has been read from the SBUF register. However, if the first byte
still hasn’t been read by the time reception of the second byte is
complete, the first byte will be lost. The serial port receive and
transmit registers are both accessed through Special Function
Register SBUF. Writing to SBUF loads the transmit register, and
reading SBUF accesses a physically separate receive register.
The serial port can be operated in 4 modes:
Mode 0
Serial data enters and exits through RxD. TxD outputs the shift
clock. 8 bits are transmitted or received, LSB first. The baud rate is
fixed at 1/6 of the CPU clock frequency.
Mode 1
10 bits are transmitted (through TxD) or received (through RxD): a
start bit (logical 0), 8 data bits (LSB first), and a stop bit (logical 1).
When data is received, the stop bit is stored in RB8 in Special
Function Register SCON. The baud rate is variable and is
determined by the T imer 1 overflow rate.
Mode 2
11 bits are transmitted (through TxD) or received (through RxD):
start bit (logical 0), 8 data bits (LSB first), a programmable 9th data
bit, and a stop bit (logical 1). When data is transmitted, the 9th data
bit (TB8 in SCON) can be assigned the value of 0 or 1. Or, for
example, the parity bit (P, in the PSW) could be moved into TB8.
When data is received, the 9th data bit goes into RB8 in Special
Function Register SCON, while the stop bit is ignored. The baud
rate is programmable to either 1/16 or 1/32 of the CPU clock
frequency, as determined by the SMOD1 bit in PCON.
Mode 3
11 bits are transmitted (through TxD) or received (through RxD): a
start bit (logical 0), 8 data bits (LSB first), a programmable 9th data
bit, and a stop bit (logical 1). In fact, Mode 3 is the same as Mode 2
in all respects except baud rate. The baud rate in Mode 3 is variable
and is determined by the T imer 1 overflow rate.
In all four modes, transmission is initiated by any instruction that
uses SBUF as a destination register. Reception is initiated in Mode 0
by the condition RI = 0 and REN = 1. Reception is initiated in the
other modes by the incoming start bit if REN = 1.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 31
Serial Port Control Register (SCON)
The serial port control and status register is the Special Function
Register SCON, shown in Figure 28. This register contains not only
the mode selection bits, but also the 9th data bit for transmit and
receive (TB8 and RB8), and the serial port interrupt bits (TI and RI).
The Framing Error bit (FE) allows detection of missing stop bits in
the received data stream. The FE bit shares the bit position SCON.7
with the SM0 bit. Which bit appears in SCON at any particular time
is determined by the SMOD0 bit in the PCON register. If SMOD0 =
0, SCON.7 is the SM0 bit. If SMOD0 = 1, SCON.7 is the FE bit.
Once set, the FE bit remains set until it is cleared by software. This
allows detection of framing errors for a group of characters without
the need for monitoring it for every character individually.
BIT SYMBOL FUNCTION
SCON.7 FE Framing Error. This bit is set by the UART receiver when an invalid stop bit is detected. Must be
cleared by software. The SMOD0 bit in the PCON register must be 1 for this bit to be accessible.
See SM0 bit below.
SCON.7 SM0 With SM1, defines the serial port mode. The SMOD0 bit in the PCON register must be 0 for this bit
to be accessible. See FE bit above.
SCON. 6 SM1 With SM0, defines the serial port mode (see table below).
SM0, SM1 UART Mode Baud Rate
0 0 0: shift register CPU clock/6
0 1 1: 8-bit UART Variable (see text)
1 0 2: 9-bit UART CPU clock/32 or CPU clock/16
1 1 3: 9-bit UART Variable (see text)
SCON.5 SM2 Enables the multiprocessor communication feature in Modes 2 and 3. In Mode 2 or 3, if SM2 is set
to 1, then Rl will not be activated if the received 9th data bit (RB8) is 0. In Mode 1, if SM2=1 then RI
will not be activated if a valid stop bit was not received. In Mode 0, SM2 should be 0.
SCON.4 REN Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
SCON.3 TB8 The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.
SCON.2 RB8 In Modes 2 and 3, is the 9th data bit that was received. In Mode 1, it SM2=0, RB8 is the stop bit that
was received. In Mode 0, RB8 is not used.
SCON.1 TI Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning
of the stop bit in the other modes, in any serial transmission. Must be cleared by software.
SCON.0 RI Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through
the stop bit time in the other modes, in any serial reception (except see SM2). Must be cleared by
software.
RI
SU01157
TIRB8TB8RENSM2SM1SM0/FE
01234567
SCON Reset Value: 00h
Bit Addressable
Address: 98h
Figure 28. Serial Port Control Register (SCON)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 32
Baud Rates
The baud rate in Mode 0 is fixed: Mode 0 Baud Rate = CPU clock/6.
The baud rate in Mode 2 depends on the value of bit SMOD1 in
Special Function Register PCON. If SMOD1 = 0 (which is the value
on reset), the baud rate is 1/32 of the CPU clock frequency. If
SMOD1 = 1, the baud rate is 1/16 of the CPU clock frequency.
Mode 2 Baud Rate +1)SMOD1
32 CPU clock frequency
Using Timer 1 to Generate Baud Rates
When T imer 1 is used as the baud rate generator, the baud rates in
Modes 1 and 3 are determined by the T imer 1 overflow rate and the
value of SMOD1. The T imer 1 interrupt should be disabled in this
application. The Timer itself can be configured for either “timer” or
“counter” operation, and in any of its 3 running modes. In the most
typical applications, it is configured for “timer” operation, in the
auto-reload mode (high nibble of TMOD = 0010b). In that case the
baud rate is given by the formula:
Mode 1, 3 Baud Rate +
CPU clock frequencyń
192(or96ifSMOD1+1)
256 *(TH1)
Tables 6 and 7 list various commonly used baud rates and how they
can be obtained using T imer 1 as the baud rate generator.
Table 9. Baud Rates, Timer Values, and CPU Clock Frequencies for SMOD1 = 0
Timer Co nt
Baud Rate
Timer
Co
u
nt
2400 4800 9600 19.2k 38.4k 57.6k
–1 0.4608 0.9216 * 1.8432 * 3.6864 * 7.3728 * 11.0592
–2 0.9216 1.8432 * 3.6864 * 7.3728 * 14.7456
–3 1.3824 2.7648 5.5296 * 11.0592 – –
–4 * 1.8432 * 3.6864 * 7.3728 * 14.7456 – –
–5 2.3040 4.6080 9.2160 * 18.4320 – –
–6 2.7648 5.5296 * 11.0592 –––
–7 3.2256 6.4512 12.9024 – – –
–8 * 3.6864 * 7.3728 * 14.7456 –––
–9 4.1472 8.2944 16.5888 – – –
–10 4.6080 9.2160 * 18.4320 –––
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 33
Table 10. Baud Rates, Timer Values, and CPU Clock Frequencies for SMOD1 = 1
Timer Co nt
Baud Rate
Timer
Co
u
nt
2400 4800 9600 19.2k 38.4k 57.6k 115.2k
–1 0.2304 0.4608 0.9216 * 1.8432 * 3.6864 5.5296 * 11.0592
–2 0.4608 0.9216 * 1.8432 * 3.6864 * 7.3728 * 11.0592 –
–3 0.6912 1.3824 2.7648 5.5296 * 11.0592 16.5888 –
–4 0.9216 * 1.8432 * 3.6864 * 7.3728 * 14.7456 – –
–5 1.1520 2.3040 4.6080 9.2160 * 18.4320 – –
–6 1.3824 2.7648 5.5296 * 11.0592 –––
–7 1.6128 3.2256 6.4512 12.9024 – – –
–8 * 1.8432 * 3.6864 * 7.3728 * 14.7456 –––
–9 2.0736 4.1472 8.2944 16.5888 – – –
–10 2.3040 4.6080 9.2160 * 18.4320 –––
–11 2.5344 5.0688 10.1376 – – – –
–12 2.7648 5.5296 * 11.0592 ––––
–13 2.9952 5.9904 11.9808 – – – –
–14 3.2256 6.4512 12.9024 – – – –
–15 3.4560 6.9120 13.8240 – – – –
–16 * 3.6864 * 7.3728 * 14.7456 ––––
–17 3.9168 7.8336 15.6672 – – – –
–18 4.1472 8.2944 16.5888 – – – –
–19 4.3776 8.7552 17.5104 – – – –
–20 4.6080 9.2160 * 18.4320 ––––
–21 4.8384 9.6768 19.3536 – – – –
NOTES TO TABLES 9 AND 10:
1. Tables 6 and 7 apply to UART modes 1 and 3 (variable rate modes), and show CPU clock rates in MHz for standard baud rates from 2400 to
115.2k baud.
2. Table 6 shows timer settings and CPU clock rates with the SMOD1 bit in the PCON register = 0 (the default after reset), while Table 7
reflects the SMOD1 bit = 1.
3. The tables show all potential CPU clock frequencies up to 20 MHz that may be used for baud rates from 9600 baud to 115.2k baud. Other
CPU clock frequencies that would give only lower baud rates are not shown.
4. Table entries marked with an asterisk (*) indicate standard crystal and ceramic resonator frequencies that may be obtained from many
sources without special ordering.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 34
More About UART Mode 0
Serial data enters and exits through RxD. TxD outputs the shift
clock. 8 bits are transmitted/received: 8 data bits (LSB first). The
baud rate is fixed at 1/6 the CPU clock frequency. Figure 29 shows
a simplified functional diagram of the serial port in Mode 0, and
associated timing.
T ransmission is initiated by any instruction that uses SBUF as a
destination register. The “write to SBUF” signal at S6P2 also loads a
1 into the 9th position of the transmit shift register and tells the TX
Control block to commence a transmission. The internal timing is
such that one full machine cycle will elapse between “write to SBUF”
and activation of SEND.
SEND enables the output of the shift register to the alternate output
function line of P1.1 and also enable SHIFT CLOCK to the alternate
output function line of P1.0. SHIFT CLOCK is low during S3, S4, and
S5 of every machine cycle, and high during S6, S1, and S2. At
S6P2 of every machine cycle in which SEND is active, the contents
of the transmit shift are shifted to the right one position.
As data bits shift out to the right, zeros come in from the left. When
the MSB of the data byte is at the output position of the shift register,
then the 1 that was initially loaded into the 9th position, is just to the
left of the MSB, and all positions to the left of that contain zeros. This
condition flags the TX Control block to do one last shift and then
deactivate SEND and set T1. Both of these actions occur at S1P1 of
the 10th machine cycle after “write to SBUF.” Reception is initiated by
the condition REN = 1 and R1 = 0. At S6P2 of the next machine
cycle, the RX Control unit writes the bits 11111110 t o the receive shift
register, and in the next clock phase activates RECEIVE.
RECEIVE enable SHIFT CLOCK to the alternate output function line
of P1.0. SHIFT CLOCK makes transitions at S3P1 and S6P1 of every
machine cycle. At S6P2 of every machine cycle in which RECEIVE is
active, the contents of the receive shift register are shifted to the left
one position. The value that comes in from the right is the value that
was sampled at the P1.1 pin at S5P2 of the same machine cycle.
As data bits come in from the right, 1s shift out to the left. When the 0
that was initially loaded into the rightmost position arrives at the
leftmost position in the shift register, it flags the RX Control block to do
one last shift and load SBUF. At S1P1 of the 10th machine cycle after
the write to SCON that cleared RI, RECEIVE is cleared as RI is set.
More About UART Mode 1
Ten bits are transmitted (through TxD), or received (through RxD): a
start bit (0), 8 data bits (LSB first), and a stop bit (1). On receive, the
stop bit goes into RB8 in SCON. In the 87LPC764 the baud rate is
determined by the T imer 1 overflow rate. Figure 30 shows a
simplified functional diagram of the serial port in Mode 1, and
associated timings for transmit receive.
T ransmission is initiated by any instruction that uses SBUF as a
destination register. The “write to SBUF” signal also loads a 1 into
the 9th bit position of the transmit shift register and flags the TX
Control unit that a transmission is requested. T ransmission actually
commences at S1P1 of the machine cycle following the next rollover
in the divide-by-16 counter. (Thus, the bit times are synchronized to
the divide-by-16 counter, not to the “write to SBUF” signal.)
The transmission begins with activation of SEND which puts the
start bit at TxD. One bit time later, DATA is activated, which enables
the output bit of the transmit shift register to TxD. The first shift pulse
occurs one bit time after that.
As data bits shift out to the right, zeros are clocked in from the left.
When the MSB of the data byte is at the output position of the shift
register, then the 1 that was initially loaded into the 9th position is
just to the left of the MSB, and all positions to the left of that contain
zeros. This condition flags the TX Control unit to do one last shift
and then deactivate SEND and set TI. This occurs at the 10th
divide-by-16 rollover after “write to SBUF.”
Reception is initiated by a detected 1-to-0 transition at RxD. For this
purpose RxD is sampled at a rate of 16 times whatever baud rate
has been established. When a transition is detected, the
divide-by-16 counter is immediately reset, and 1FFH is written into
the input shift register. Resetting the divide-by-16 counter aligns its
rollovers with the boundaries of the incoming bit times.
The 16 states of the counter divide each bit time into 16ths. At the
7th, 8th, and 9th counter states of each bit time, the bit detector
samples the value of RxD. The value accepted is the value that was
seen in at least 2 of the 3 samples. This is done for noise rejection.
If the value accepted during the first bit time is not 0, the receive
circuits are reset and the unit goes back to looking for another 1-to-0
transition. This is to provide rejection of false start bits. If the start bit
proves valid, it is shifted into the input shift register, and reception of
the rest of the frame will proceed.
As data bits come in from the right, 1s shift out to the left. When the
start bit arrives at the leftmost position in the shift register (which in
mode 1 is a 9-bit register), it flags the RX Control block to do one
last shift, load SBUF and RB8, and set RI. The signal to load SBUF
and RB8, and to set RI, will be generated if, and only if, the following
conditions are met at the time the final shift pulse is generated.: 1.
R1 = 0, and 2. Either SM2 = 0, or the received stop bit = 1.
If either of these two conditions is not met, the received frame is
irretrievably lost. If both conditions are met, the stop bit goes into
RB8, the 8 data bits go into SBUF, and RI is activated. At this time,
whether the above conditions are met or not, the unit goes back to
looking for a 1-to-0 transition in RxD.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 35
80C51 INTERNAL BUS
SU01178
80C51 INTERNAL BUS
WRITE
TO
SBUF
SBUF
ZERO DETECTOR
RxD
P1.1 ALT
OUTPUT
FUNCTION
TX CONTROL
S
TX CLOCK
START
Q
CL
D
SERIAL PORT
INTERRUPT SHIFT
CLOCK
SHIFT
SEND
S6
RXD
P1.1 ALT
INPUT
FUNCTION
LOAD
SBUF
TI
INPUT SHIFT REGISTER
START
RI RECEIVE
SHIFT
TX CLOCK RX CONTROL
REN
RI
SBUF
READ
SBUF
TRANSMIT
TxD
P1.0 ALT
OUTPUT
FUNCTION
SEND
RXD (DATA OUT) D0 D1 D5D2 D6D3 D4 D7
TXD (SHIFT CLOCK)
SHIFT
S1 ... S6 S1 ... S6 S1 ... S6 S1 ... S6S1 ... S6S1 ... S6 S1 ... S6 S1 ... S6 S1 ... S6 S1 ... S6S1 ... S6S1 ... S6 S1 ... S6
WRITE TO SBUF
TI
RECEIVE
RECEIVE
D0 D1 D5D2 D6D3 D4 D7
TxD (SHIFT CLOCK)
SHIFT
WRITE TO SCON (CLEAR RI)
RI
RxD (DATA IN)
11 11111 0
Figure 29. Serial Port Mode 0
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 36
SU01179
80C51 INTERNAL BUS
WRITE
TO SBUF
SBUF
ZERO DETECTOR
TxD
P1.0 ALT
OUTPUT
FUNCTION
TX CONTROL
S
TX CLOCK
START
Q
CL
D
SERIAL PORT
INTERRUPT
SHIFT
SEND
LOAD
SBUF
TI
INPUT SHIFT REGISTER
START
RI LOAD SBUF
SHIFT
RX
CLOCK
1FFH
RX CONTROL
SBUF
READ
SBUF
TRANSMIT
RxD
P1.1 ALT
INPUT
FUNCTION
80C51 INTERNAL BUS
DATA
TB8
÷16
÷16
÷2
TIMER 1
OVERFLOW
SMOD1 = 0 SMOD1
= 1
1-TO-0
TRANSITION
DETECTOR
BIT
DETECTOR
START
BIT STOP BIT
TX CLOCK
WRITE TO SBUF
SEND
DATA
SHIFT
TxD
TI
D0 D1 D5D2 D6D3 D4 D7
RECEIVE
RX CLOCK
SHIFT
RI
BIT DETECTOR SAMPLE TIMES
START
BIT STOP BIT
RxD D0 D1 D5D2 D6D3 D4 D7
÷ 16 RESET
Figure 30. Serial Port Mode 1
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 37
More About UART Modes 2 and 3
Eleven bits are transmitted (through TxD), or received (through
RxD): a start bit (0), 8 data bits (LSB first), a programmable 9th data
bit, and a stop bit (1). On transmit, the 9th data bit (TB8) can be
assigned the value of 0 or 1. On receive, the 9the data bit goes into
RB8 in SCON. The baud rate is programmable to either 1/16 or 1/32
of the CPU clock frequency in Mode 2. Mode 3 may have a variable
baud rate generated from T imer 1.
Figures 31 and 32 show a functional diagram of the serial port in
Modes 2 and 3. The receive portion is exactly the same as in Mode 1.
The transmit portion differs from Mode 1 only in the 9th bit of the
transmit shift register.
T ransmission is initiated by any instruction that uses SBUF as a
destination register. The “write to SBUF” signal also loads TB8 into
the 9th bit position of the transmit shift register and flags the TX
Control unit that a transmission is requested. T ransmission
commences at S1P1 of the machine cycle following the next rollover
in the divide-by-16 counter. (Thus, the bit times are synchronized to
the divide-by-16 counter, not to the “write to SBUF” signal.)
The transmission begins with activation of SEND, which puts the
start bit at TxD. One bit time later, DATA is activated, which enables
the output bit of the transmit shift register to TxD. The first shift pulse
occurs one bit time after that. The first shift clocks a 1 (the stop bit)
into the 9th bit position of the shift register. Thereafter, only zeros
are clocked in. Thus, as data bits shift out to the right, zeros are
clocked in from the left. When TB8 is at the output position of the
shift register, then the stop bit is just to the left of TB8, and all
positions to the left of that contain zeros. This condition flags the TX
Control unit to do one last shift and then deactivate SEND and set
TI. This occurs at the 1 1th divide-by-16 rollover after “write to SBUF.”
Reception is initiated by a detected 1-to-0 transition at RxD. For this
purpose RxD is sampled at a rate of 16 times whatever baud rate
has been established. When a transition is detected, the
divide-by-16 counter is immediately reset, and 1FFH is written to the
input shift register.
At the 7th, 8th, and 9th counter states of each bit time, the bit
detector samples the value of R–D. The value accepted is the value
that was seen in at least 2 of the 3 samples. If the value accepted
during the first bit time is not 0, the receive circuits are reset and the
unit goes back to looking for another 1-to-0 transition. If the start bit
proves valid, it is shifted into the input shift register, and reception of
the rest of the frame will proceed.
As data bits come in from the right, 1s shift out to the left. When the
start bit arrives at the leftmost position in the shift register (which in
Modes 2 and 3 is a 9-bit register), it flags the RX Control block to do
one last shift, load SBUF and RB8, and set RI.
The signal to load SBUF and RB8, and to set RI, will be generated
if, and only if, the following conditions are met at the time the final
shift pulse is generated. 1. RI = 0, and 2. Either SM2 = 0, or the
received 9th data bit = 1.
If either of these conditions is not met, the received frame is
irretrievably lost, and RI is not set. If both conditions are met, the
received 9th data bit goes into RB8, and the first 8 data bits go into
SBUF. One bit time later, whether the above conditions were met
or not, the unit goes back to looking for a 1-to-0 transition at the
RxD input.
Multiprocessor Communications
UART modes 2 and 3 have a special provision for multiprocessor
communications. In these modes, 9 data bits are received or
transmitted. When data is received, the 9th bit is stored in RB8. The
UART can be programmed such that when the stop bit is received,
the serial port interrupt will be activated only if RB8 = 1. This feature
is enabled by setting bit SM2 in SCON. One way to use this feature
in multiprocessor systems is as follows:
When the master processor wants to transmit a block of data to one
of several slaves, it first sends out an address byte which identifies
the target slave. An address byte differs from a data byte in that the
9th bit is 1 in an address byte and 0 in a data byte. With SM2 = 1, no
slave will be interrupted by a data byte. An address byte, however,
will interrupt all slaves, so that each slave can examine the received
byte and see if it is being addressed. The addressed slave will clear
its SM2 bit and prepare to receive the data bytes that follow. The
slaves that weren’t being addressed leave their SM2 bits set and go
on about their business, ignoring the subsequent data bytes.
SM2 has no effect in Mode 0, and in Mode 1 can be used to check
the validity of the stop bit, although this is better done with the
Framing Error flag. In a Mode 1 reception, if SM2 = 1, the receive
interrupt will not be activated unless a valid stop bit is received.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 38
START
BIT
SU01180
80C51 INTERNAL BUS
WRITE TO SBUF
SBUF
ZERO DETECTOR
TxD
P1.0 ALT OUTPUT
FUNCTION
TX CONTROL
S
TX CLOCK
START
Q
CL
D
SERIAL PORT INTERRUPT
SHIFT
SEND
LOAD
SBUF
TI
INPUT SHIFT REGISTER
START
RI LOAD SBUF
SHIFT
RX
CLOCK
1FFH
RX CONTROL
SBUF
READ
SBUF
RxD
P1.1 ALT
INPUT
FUNCTION
80C51 INTERNAL BUS
DATA
TB8
÷16
÷16
÷2
PHASE 2 CLOCK
(1/2 fOSC)
1-TO-0
TRANSITION
DETECTOR
BIT DETECTOR
STOP BIT GEN.
SMOD1 = 0 SMOD1
= 1
TRANSMIT
START
BIT STOP BIT
TX CLOCK
WRITE TO SBUF
SEND
DATA
SHIFT
TxD
TI
D0 D1 D5D2 D6D3 D4 D7
RECEIVE
RX CLOCK
SHIFT
RI
BIT DETECTOR SAMPLE TIMES
STOP BIT
RxD D0 D1 D5D2 D6D3 D4 D7
÷ 16 RESET
TB8
STOP BIT GEN.
RB8
Figure 31. Serial Port Mode 2
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 39
BIT
DETECTOR
SU01181
TRANSMIT
START
BIT STOP BIT
TX CLOCK
WRITE TO SBUF
SEND
DATA
SHIFT
TxD
TI
D0 D1 D5D2 D6D3 D4 D7
RECEIVE
RX CLOCK
SHIFT
RI
BIT DETECTOR SAMPLE TIMES
START
BIT STOP BIT
RxD D0 D1 D5D2 D6D3 D4 D7
÷ 16 RESET
TB8
STOP BIT GEN.
RB8
80C51 INTERNAL BUS
WRITE TO SBUF
SBUF
ZERO DETECTOR
TxD
P1.0 ALT
OUTPUT
FUNCTION
TX CONTROL
S
TX CLOCK
START
Q
CL
D
SERIAL PORT INTERRUPT
SHIFT
SEND
LOAD
SBUF
TI
INPUT SHIFT REGISTER
START
RI LOAD SBUF
SHIFT
RX
CLOCK
1FFH
RX CONTROL
SBUF
READ
SBUF
RxD
P1.1 ALT
INPUT
FUNCTION
80C51 INTERNAL BUS
DATA
TB8
÷16
÷16
÷2
TIMER 1
OVERFLOW
SMOD1 = 0 SMOD1
= 1
1-TO-0
TRANSITION
DETECTOR
Figure 32. Serial Port Mode 3
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 40
Automatic Address Recognition
Automatic Address Recognition is a feature which allows the UART
to recognize certain addresses in the serial bit stream by using
hardware to make the comparisons. This feature saves a great deal
of software overhead by eliminating the need for the software to
examine every serial address which passes by the serial port. This
feature is enabled by setting the SM2 bit in SCON. In the 9 bit UART
modes, mode 2 and mode 3, the Receive Interrupt flag (RI) will be
automatically set when the received byte contains either the “Given”
address or the “Broadcast” address. The 9 bit mode requires that
the 9th information bit is a 1 to indicate that the received information
is an address and not data.
Using the Automatic Address Recognition feature allows a master to
selectively communicate with one or more slaves by invoking the
Given slave address or addresses. All of the slaves may be
contacted by using the Broadcast address. Two special Function
Registers are used to define the slave’s address, SADDR, and the
address mask, SADEN. SADEN is used to define which bits in the
SADDR are to be used and which bits are “don’t care”. The SADEN
mask can be logically ANDed with the SADDR to create the “Given”
address which the master will use for addressing each of the slaves.
Use of the Given address allows multiple slaves to be recognized
while excluding others. The following examples will help to show the
versatility of this scheme:
Slave 0 SADDR = 1100 0000
SADEN = 1111 1101
Given = 1100 00X0
Slave 1 SADDR = 1100 0000
SADEN = 1111 1110
Given = 1100 000X
In the above example SADDR is the same and the SADEN data is
used to differentiate between the two slaves. Slave 0 requires a 0 in
bit 0 and it ignores bit 1. Slave 1 requires a 0 in bit 1 and bit 0 is
ignored. A unique address for Slave 0 would be 1100 0010 since
slave 1 requires a 0 in bit 1. A unique address for slave 1 would be
1100 0001 since a 1 in bit 0 will exclude slave 0. Both slaves can be
selected at the same time by an address which has bit 0 = 0 (for
slave 0) and bit 1 = 0 (for slave 1). Thus, both could be addressed
with 1100 0000.
In a more complex system the following could be used to select
slaves 1 and 2 while excluding slave 0:
Slave 0 SADDR = 1100 0000
SADEN = 1111 1001
Given = 1100 0XX0
Slave 1 SADDR = 1110 0000
SADEN = 1111 1010
Given = 1110 0X0X
Slave 2 SADDR = 1110 0000
SADEN = 1111 1100
Given = 1110 00XX
In the above example the differentiation among the 3 slaves is in the
lower 3 address bits. Slave 0 requires that bit 0 = 0 and it can be
uniquely addressed by 1110 0110. Slave 1 requires that bit 1 = 0 and
it can be uniquely addressed by 1110 and 0101. Slave 2 requires
that bit 2 = 0 and its unique address is 1110 0011. To select Slaves 0
and 1 and exclude Slave 2 use address 1110 0100, since it is
necessary to make bit 2 = 1 to exclude slave 2. The Broadcast
Address for each slave is created by taking the logical OR of SADDR
and SADEN. Zeros in this result are treated as don’t-cares. In most
cases, interpreting the don’t-cares as ones, the broadcast address
will be FF hexadecimal. Upon reset SADDR and SADEN are loaded
with 0s. This produces a given address of all “don’t cares” as well as
a Broadcast address of all “don’t cares”. This effectively disables the
Automatic Addressing mode and allows the microcontroller to use
standard UART drivers which do not make use of this feature.
Watchdog Timer
When enabled via the WDTE configuration bit, the watchdog timer is
operated from an independent, fully on-chip oscillator in order to
provide the greatest possible dependability. When the watchdog
feature is enabled, the timer must be fed regularly by software in
order to prevent it from resetting the CPU, and it cannot be turned of f.
When disabled as a watchdog timer (via the WDTE bit in the UCFG1
configuration register), it may be used as an interval timer and may
generate an interrupt. The watchdog timer is shown in Figure 33.
The watchdog timeout time is selectable from one of eight values,
nominal times range from 16 milliseconds to 2.1 seconds. The
frequency tolerance of the independent watchdog RC oscillator is
±37%. The timeout selections and other control bits are shown in
Figure 34. When the watchdog function is enabled, the WDCON
register may be written once during chip initialization in order to set
the watchdog timeout time. The recommended method of initializing
the WDCON register is to first feed the watchdog, then write to
WDCON to configure the WDS2–0 bits. Using this method, the
watchdog initialization may be done any time within 10 milliseconds
after startup without a watchdog overflow occurring before the
initialization can be completed.
Since the watchdog timer oscillator is fully on-chip and independent
of any external oscillator circuit used by the CPU, it intrinsically
serves as an oscillator fail detection function. If the watchdog feature
is enabled and the CPU oscillator fails for any reason, the watchdog
timer will time out and reset the CPU.
When the watchdog function is enabled, the timer is deactivated
temporarily when a chip reset occurs from another source, such as
a power on reset, brownout reset, or external reset.
W atchdog Feed Sequence
If the watchdog timer is running, it must be fed before it times out in
order to prevent a chip reset from occurring. The watchdog feed
sequence consists of first writing the value 1Eh, then the value E1h
to the WDRST register. An example of a watchdog feed sequence is
shown below.
WDFeed:
mov WDRST,#1eh ; First part of watchdog feed sequence.
mov WDRST,#0e1h ; Second part of watchdog feed sequence.
The two writes to WDRST do not have to occur in consecutive
instructions. An incorrect watchdog feed sequence does not cause
any immediate response from the watchdog timer, which will still
time out at the originally scheduled time if a correct feed sequence
does not occur prior to that time.
After a chip reset, the user program has a limited time in which to
either feed the watchdog timer or change the timeout period. When
a low CPU clock frequency is used in the application, the number of
instructions that can be executed before the watchdog overflows
may be quite small.
W atchdog Reset
If a watchdog reset occurs, the internal reset is active for
approximately one microsecond. If the CPU clock was still running,
code execution will begin immediately after that. If the processor
was in Power Down mode, the watchdog reset will start the oscillator
and code execution will resume after the oscillator is stable.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 41
SU01182
WATCHDOG
INTERRUPT
S
Q
20-BIT COUNTER
STATE CLOCK
WDTE (UCFG1.7)
BOD (xxx.x)
POR (xxx.x)
WATCHDOG
RESET
CLEAR
8 MSBs
8 TO 1 MUX
WATCHDOG
FEED DETECT WDOVF
(WDCON.5)
WDS2–0
(WDCON.2–0)
WDTE + WDRUN
WDCLK * WDTE
500 kHz
R/C OSCILLATOR
ENABLE
CLOCK OUT
R
Figure 33. Block Diagram of the Watchdog Timer
BIT SYMBOL FUNCTION
WDCON.7, 6 — Reserved for future use. Should not be set to 1 by user programs.
WDCON.5 WDOVF Watchdog timer overflow flag. Set when a watchdog reset or timer overflow occurs. Cleared when
the watchdog is fed.
WDCON.4 WDRUN Watchdog run control. The watchdog timer is started when WDRUN = 1 and stopped when
WDRUN = 0. This bit is forced to 1 (watchdog running) if the WDTE configuration bit = 1.
WDCON.3 WDCLK Watchdog clock select. The watchdog timer is clocked by CPU clock/6 when WDCLK = 1 and by
the watchdog RC oscillator when WDCLK = 0. This bit is forced to 0 (using the watchdog RC
oscillator) if the WDTE configuration bit = 1.
WDCON.2–0 WDS2–0 Watchdog rate select.
WDS2–0 T imeout Clocks Minimum T ime Nominal Time Maximum T ime
0 0 0 8,192 10 ms 16 ms 23 ms
0 0 1 16,384 20 ms 32 ms 45 ms
0 1 0 32,768 41 ms 65 ms 90 ms
0 1 1 65,536 82 ms 131 ms 180 ms
1 0 0 131,072 165 ms 262 ms 360 ms
1 0 1 262,144 330 ms 524 ms 719 ms
1 1 0 524,288 660 ms 1.05 sec 1.44 sec
1 1 1 1,048,576 1.3 sec 2.1 sec 2.9 sec
WDS0
SU01183
WDS1WDS2WDCLKWDRUNWDOVF——
01234567
WDCON Reset Value: S 30h for a watchdog reset.
S 10h for other rest sources if the watchdog is enabled via the WDTE configuration bit.
S 00h for other reset sources if the watchdog is disabled via the WDTE configuration bit.
Not Bit Addressable
Address: A7h
Figure 34. W atchdog Timer Control Register (WDCON)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 42
Additional Features
The AUXR1 register contains several special purpose control bits that
relate to several chip features. AUXR1 is described in Figure 35.
Software Reset
The SRST bit in AUXR1 allows software the opportunity to reset the
processor completely, as if an external reset or watchdog reset had
occurred. If a value is written to AUXR1 that contains a 1 at bit
position 3, all SFRs will be initialized and execution will resume at
program address 0000. Care should be taken when writing to
AUXR1 to avoid accidental software resets.
Dual Data Pointers
The dual Data Pointer (DPTR) adds to the ways in which the
processor can specify the address used with certain instructions.
The DPS bit in the AUXR1 register selects one of the two Data
Pointers. The DPTR that is not currently selected is not accessible
to software unless the DPS bit is toggled.
Specific instructions affected by the Data Pointer selection are:
•INC DPTR Increments the Data Pointer by 1.
•JMP @A+DPTR Jump indirect relative to DPTR value.
•MOV DPTR, #data16 Load the Data Pointer with a 16-bit
constant.
•MOVC A, @A+DPTR Move code byte relative to DPTR to the
accumulator.
•MOVX A, @DPTR Move data byte the accumulator to data
memory relative to DPTR.
•MOVX @DPTR, A Move data byte from data memory
relative to DPTR to the accumulator.
Also, any instruction that reads or manipulates the DPH and DPL
registers (the upper and lower bytes of the current DPTR) will be
affected by the setting of DPS. The MOVX instructions have limited
application for the 87LPC764 since the part does not have an
external data bus. However, they may be used to access EPROM
configuration information (see EPROM Characteristics section).
Bit 2 of AUXR1 is permanently wired as a logic 0. This is so that the
DPS bit may be toggled (thereby switching Data Pointers) simply by
incrementing the AUXR1 register, without the possibility of
inadvertently altering other bits in the register.
BIT SYMBOL FUNCTION
AUXR1.7 KBF Keyboard Interrupt Flag. Set when any pin of port 0 that is enabled for the Keyboard Interrupt
function goes low. Must be cleared by software.
AUXR1.6 BOD Brown Out Disable. When set, turns off brownout detection and saves power. See Power
Monitoring Functions section for details.
AUXR1.5 BOI Brown Out Interrupt. When set, prevents brownout detection from causing a chip reset and allows
the brownout detect function to be used as an interrupt. See the Power Monitoring Functions
section for details.
AUXR1.4 LPEP Low Power EPROM control bit. Allows power savings in low voltage systems. Set by software. Can
only be cleared by power-on or brownout reset. See the Power Reduction Modes section for
details.
AUXR1.3 SRST Software Reset. When set by software, resets the 87LPC764 as if a hardware reset occurred.
AUXR1.2 — This bit contains a hard-wired 0. Allows toggling of the DPS bit by incrementing AUXR1, without
interfering with other bits in the register.
AUXR1.1 — Reserved for future use. Should not be set to 1 by user programs.
AUXR1.0 DPS Data Pointer Select. Chooses one of two Data Pointers for use by the program. See text for details.
DPS
SU01184
—0SRSTLPEPBOIBODKBF
01234567
AUXR1 Reset Value: 00h
Not Bit Addressable
Address: A2h
Figure 35. AUXR1 Register
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 43
EPROM Characteristics
Programming of the EPROM on the 87LPC764 is accomplished with
a serial programming method. Commands, addresses, and data are
transmitted to and from the device on two pins after programming
mode is entered. Serial programming allows easy implementation of
in-circuit programming of the 87LPC764 in an application board.
Details of the programming algorithm may be found in a separate
document that is available on the Philips web site at:
http://www.semiconductors.philips.com/mcu/support/progspecs/
The 87LPC764 contains three signature bytes that can be read and
used by an EPROM programming system to identify the device. The
signature bytes designate the device as an 87LPC764 manufactured
by Philips. The signature bytes may be read by the user program at
addresses FC30h, FC31h and FC60h with the MOVC instruction,
using the DPTR register for addressing.
A special user data area is also available for access via the MOVC
instruction at addresses FCE0h through FCFFh. This “customer
code” space is programmed in the same manner as the main code
EPROM and may be used to store a serial number, manufacturing
date, or other application information.
32-Byte Customer Code Space
A small supplemental EPROM space is reserved for use by the
customer in order to identify code revisions, store checksums, add a
serial number to each device, or any other desired use. This area
exists in the code memory space from addresses FCE0h through
FCFFh. Code execution from this space is not supported, but it may
be read as data through the use of the MOVC instruction with the
appropriate addresses. The memory may be programmed at the
same time as the rest of the code memory and UCFG bytes are
programmed.
System Configuration Bytes
A number of user configurable features of the 87LPC764 must be
defined at power up and therefore cannot be set by the program after
start of execution. Those features are configured through the use of
two EPROM bytes that are programmed in the same manner as the
EPROM program space. The contents of the two configuration bytes,
UCFG1 and UCFG2, are shown in Figures 36 and 37. The values of
these bytes may be read by the program through the use of the
MOVX instruction at the addresses shown in the figure.
BIT SYMBOL FUNCTION
UCFG1.7 WDTE W atchdog timer enable. When programmed (0), disables the watchdog timer. The timer may
still be used to generate an interrupt.
UCFG1.6 RPD Reset pin disable. When 1 disables the reset function of pin P1.5, allowing it to be used as an
input only port pin.
UCFG1.5 PRHI Port reset high. When 1, ports reset to a high state. When 0, ports reset to a low state.
UCFG1.4 BOV Brownout voltage select. When 1, the brownout detect voltage is 2.5V. When 0, the brownout
detect voltage is 3.8V. This is described in the Power Monitoring Functions section.
UCFG1.3 CLKR Clock rate select. When 0, the CPU clock rate is divided by 2. This results in machine cycles
taking 12 CPU clocks to complete as in the standard 80C51. For full backward compatibility,
this division applies to peripheral timing as well.
UCFG1.2–0 FOSC2–FSOC0 CPU oscillator type select. See Oscillator section for additional information. Combinations
other than those shown below should not be used. They are reserved for future use.
FOSC2–FOSC0 Oscillator Configuration
1 1 1 External clock input on X1 (default setting for an unprogrammed part).
0 1 1 Internal RC oscillator, 6 MHz ±25%.
0 1 0 Low frequency crystal, 20 kHz to 100 kHz.
0 0 1 Medium frequency crystal or resonator, 100 kHz to 4 MHz.
0 0 0 High frequency crystal or resonator, 4 MHz to 20 MHz.
FOSC0
SU01185
FOSC1FOSC2CLKRBOVPRHIRPDWDTE
01234567
UCFG1 Unprogrammed Value: FFh
Address: FD00h
Figure 36. EPROM System Configuration Byte 1 (UCFG1)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 44
BIT SYMBOL FUNCTION
UCFG2.7, 6 SB2, SB1 EPROM security bits. See table entitled, “EPROM Security Bits” for details.
UCFG2.5–0 — Reserved for future use.
—
SU01186
—————SB1SB2
01234567
UCFG2 Unprogrammed Value: FFh
Address: FD01h
Figure 37. EPROM System Configuration Byte 2 (UCFG2)
Security Bits
When neither of the security bits are programmed, the code in the EPROM can be verified. When only security bit 1 is programmed, all further
programming of the EPROM is disabled. At that point, only security bit 2 may still be programmed. When both security bits are programmed,
EPROM verify is also disabled.
Table 11. EPROM Security Bits
SB2 SB1 Protection Description
1 1 Both security bits unprogrammed. No program security features enabled. EPROM is programmable and verifiable.
1 0 Only security bit 1 programmed. Further EPROM programming is disabled. Security bit 2 may still be programmed.
0 1 Only security bit 2 programmed. This combination is not supported.
0 0 Both security bits programmed. All EPROM verification and programming are disabled.
ABSOLUTE MAXIMUM RATINGS
PARAMETER RATING UNIT
Operating temperature under bias –55 to +125 °C
Storage temperature range –65 to +150 °C
Voltage on RST/VPP pin to VSS 0 to +11.0 V
Voltage on any other pin to VSS –0.5 to VDD+0.5V V
Maximum IOL per I/O pin 20 mA
Power dissipation (based on package heat transfer, not device power consumption) 1.5 W
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section
of this specification are not implied.
2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless otherwise noted.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 45
DC ELECTRICAL CHARACTERISTICS
VDD = 2.7 V to 6.0 V unless otherwise specified; Tamb = 0°C to +70°C or –40°C to +85°C, unless otherwise specified.
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
TEST
CONDITIONS
MIN TYP1MAX
UNIT
I
Power su
pp
ly current o
p
erating
5.0 V, 20 MHz11 15 25 mA
I
DD
Po
w
er
s
u
ppl
y
c
u
rrent
,
operating
3.0 V, 10 MHz11 4 7 mA
I
Power su
pp
ly current Idle mode
5.0 V, 20 MHz11 6 10 mA
I
ID
Po
w
er
s
u
ppl
y
c
u
rrent
,
Idle
mode
3.0 V, 10 MHz11 2 4 mA
I
Power su
pp
ly current Power Down mode
5.0 V11 1 10 µA
I
PD
Po
w
er
s
u
ppl
y
c
u
rrent
,
Po
w
er
Do
w
n
mode
3.0 V11 1 5 µA
VRAM RAM keep-alive voltage 1.5 V
V
In
p
ut low voltage (TTL in
p
ut)
4.0 V < VDD < 6.0 V –0.5 0.2 VDD–0.1 V
V
IL
Inp
u
t
lo
w v
oltage
(TTL
inp
u
t)
2.7 V < VDD < 4.0 V –0.5 0.7 V
VIL1 Negative going threshold (Schmitt input) –0.5 VDD 0.4 VDD 0.3 VDD V
VIH Input high voltage (TTL input) 0.2 VDD+0.9 VDD+0.5 V
VIH1 Positive going threshold (Schmitt input) 0.7 VDD 0.6 VDD VDD+0.5 V
HYS Hysteresis voltage 0.2 VDD V
VOL Output low voltage all ports5, 9IOL = 3.2 mA, VDD = 2.7 V 0.4 V
VOL1 Output low voltage all ports5, 9IOL = 20 mA, VDD = 2.7 V 1.0 V
VO
Out
p
ut high voltage all
p
orts3
IOH = –20 µA, VDD = 2.7 V VDD–0.7 V
V
OH
O
u
tp
u
t
high
v
oltage
,
all
ports3
IOH = –30 µA, VDD = 4.5 V VDD–0.7 V
VOH1 Output high voltage, all ports4IOH = –1.0 mA, VDD = 2.7 V VDD–0.7 V
CIO Input/Output pin capacitance10 15 pF
IIL Logical 0 input current, all ports8VIN = 0.4 V –50 µA
ILI Input leakage current, all ports7VIN = VIL or VIH ±2µA
I
Logical 1 to 0 transition current all
p
orts3, 6
VIN = 1.5 V at VDD = 3.0 V –30 –250 µA
I
TL
Logical
1
to
0
transition
c
u
rrent
,
all
ports3
,
6
VIN = 2.0 V at VDD = 5.5 V –150 –650 µA
RRST Internal reset pull-up resistor 40 225 kΩ
VBO2.5 Brownout trip voltage with BOV = 112 Tamb = 0°C to +70°C 2.45 2.5 2.65 V
VBO3.8 Brownout trip voltage with BOV = 0 3.45 3.8 3.90 V
VREF Reference voltage 1.11 1.26 1.41 V
tC (VREF)Temperature coefficient tbd ppm/°C
SS Supply sensitivity tbd %/V
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5 V.
2. See other Figures for details.
Active mode: ICC(MAX) = tbd
Idle mode: ICC(MAX) = tbd
3. Ports in quasi-bidirectional mode with weak pull-up (applies to all port pins with pull-ups). Does not apply to open drain pins.
4. Ports in PUSH-PULL mode. Does not apply to open drain pins.
5. In all output modes except high impedance mode.
6. Port pins source a transition current when used in quasi-bidirectional mode and externally driven from 1 to 0. This current is highest when
VIN is approximately 2 V.
7. Measured with port in high impedance mode. Parameter is guaranteed but not tested at cold temperature.
8. Measured with port in quasi-bidirectional mode.
9. Under steady state (non-transient) conditions, IOL must be externally limited as follows:
Maximum IOL per port pin: 20 mA
Maximum total IOL for all outputs: 80 mA
Maximum total IOH for all outputs: 5 mA
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
10.Pin capacitance is characterized but not tested.
11. The IDD, IID, and IPD specifications are measured using an external clock with the following functions disabled: comparators, brownout
detect, and watchdog timer. For VDD = 3 V, LPEP = 1. Refer to the appropriate figures on the following pages for additional current drawn by
each of these functions and detailed graphs for other frequency and voltage combinations.
12.Devices initially operating at VDD = 2.7V or above and at fOSC = 10 MHz or less are guaranteed to continue to execute instructions correctly
at the brownout trip point. Initial power-on operation below VDD = 2.7 V is not guaranteed.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 46
COMPARATOR ELECTRICAL CHARACTERISTICS
VDD = 3.0 V to 6.0 V unless otherwise specified; Tamb = 0°C to +70°C or –40°C to +85°C, unless otherwise specified
SYMBOL
PARAMETER
TEST CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
TEST
CONDITIONS
MIN TYP MAX
UNIT
VIO Offset voltage comparator inputs1±10 mV
VCR Common mode range comparator inputs 0 VDD–0.3 V
CMRR Common mode rejection ratio1–50 dB
Response time 250 500 ns
Comparator enable to output valid 10 µs
IIL Input leakage current, comparator 0 < VIN < VDD ±10 µA
NOTE:
1. This parameter is guaranteed by characterization, but not tested in production.
AC ELECTRICAL CHARACTERISTICS
Tamb = 0°C to +70°C or –40°C to +85°C, VDD = 2.7 V to 6.0 V unless otherwise specified, VSS = 0 V1, 2, 3
SYMBOL
FIGURE
PARAMETER
LIMITS
UNIT
SYMBOL
FIGURE
PARAMETER
MIN MAX
UNIT
External Clock
fC39 Oscillator frequency (VDD = 4.5 V to 6.0 V) 0 20 MHz
fC39 Oscillator frequency (VDD = 2.7 V to 6.0 V) 0 10 MHz
tC39 Clock period and CPU timing cycle 1/fCns
tCHCX 39 Clock high-time420 ns
tCLCX 39 Clock low time420 ns
Shift Register
tXLXL 38 Serial port clock cycle time 6tCns
tQVXH 38 Output data setup to clock rising edge 5tC – 133 ns
tXHQX 38 Output data hold after clock rising edge 1tC – 80 ns
tXHDV 38 Input data setup to clock rising edge 5tC – 133 ns
tXHDX 38 Input data hold after clock rising edge 0 ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for all outputs = 80 pF.
3. Parts are guaranteed to operate down to 0 Hz.
4. Applies only to an external clock source, not when a crystal is connected to the X1 and X2 pins.
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 47
CLEAR RI
tXLXL
CLOCK
tXHQX
tQVXH
OUTPUT DATA
WRITE TO SBUF
INPUT DATA
tXHDV
tXHDX SET TI
SET RI
SU01187
71234560
VALID VALID VALID VALID VALID VALID VALID VALID
Figure 38. Shift Register Mode Timing
SU01188
VDD – 0.5
0.45V
0.2VDD + 0.9
0.2 VDD – 0.1
tCHCL tCLCH
tCHCX
tCLCX
tC
Figure 39. External Clock Timing
SU01202
100
10
1
10 100
Idd (uA)
Frequency (kHz)
6.0 V
5.0 V
4.0 V
3.3 V
2.7 V
Figure 40. Typical Idd versus frequency (low frequency
oscillator, 25°C)
SU01203
1000
100
10
100 10,000
Idd (uA)
Frequency (kHz)
1,000
6.0 V
5.0 V
2.7 V
6.0 V
5.0 V
4.0 V
3.3 V
2.7 V
Figure 41. T ypical Idd versus frequency (medium frequency
oscillator, 25°C)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 48
SU01204
10,000
1,000
100
1 100
Idd (uA)
Frequency (MHz)
10
6.0 V
5.0 V
4.0 V
3.3 V
2.7 V
Figure 42. T ypical Idd versus frequency (high frequency
oscillator, 25°C)
SU01205
100,000
100
1010 100,000
Idd (uA)
Frequency (kHz)
1,000
10,000
6.0 V 5.0 V
4.0 V
3.3 V
2.7 V
100 1,000 10,000
Figure 43. T ypical Active Idd versus frequency (external clock,
25°C, LPEP=0)
SU01206
10,000
100
110 10,000
Idd (uA)
Frequency (kHz)
4.0 V
3.3 V
2.7 V
100 1,000
1,000
10
Figure 44. T ypical Active Idd versus frequency (external clock,
25°C, LPEP=1)
SU01207
100
10
1
10 100
Idd (uA)
Frequency (kHz)
4.0 V
3.3 V
2.7 V
1,000
10,000
1,000 10,000
Figure 45. T ypical Idle Idd versus frequency (external clock,
25°C, LPEP=1)
SU01208
10,000
1,000
1010 100,000
Idd (uA)
Frequency (kHz)
100 1,000 10,000
100
6.0 V
5.0 V
4.0 V
3.3 V
2.7 V
Figure 46. T ypical Idle Idd versus frequency (external clock,
25°C, LPEP=0)
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 49
DIP20: plastic dual in-line package; 20 leads (300 mil) SOT146-1
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 50
SO20: plastic small outline package; 20 leads; body width 7.5 mm SOT163-1
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 51
NOTES
Philips Semiconductors Preliminary specification
87LPC764
Low power, low price, low pin count (20 pin)
microcontroller with 4 kB OTP
2000 Jun 01 52
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may af fect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury . Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
Copyright Philips Electronics North America Corporation 2000
All rights reserved. Printed in U.S.A.
Date of release: 06-00
Document order number: 9397 750 07176
Data sheet
status
Objective
specification
Preliminary
specification
Product
specification
Product
status
Development
Qualification
Production
Definition [1]
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make changes at any time without notice in order to
improve design and supply the best possible product.
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
Data sheet status
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Go to Philips Semiconductors' home page
Select & Go...
Start
part
Catalog & Datasheets
Catalog by Function
Discrete semiconductors
Audio
Clocks and Watches
Data communications
Microcontrollers
Peripherals
Standard analog
Video
Wired communications
Wireless communications
Catalog by System
Automotive
Consumer Multimedia
Systems
Communications
PC/PC-peripherals
Cross reference
Models
Packages
Application notes
Selection guides
Other technical documentation
End of Life information
Datahandbook system
Relevant Links
About catalog tree
About search
About this site
Subscribe to eNews
Catalog & Datasheets
Search 87LPC764
87LPC764
Information as of 2000-08-23
87LPC764; Low power, low price, low pin count (20 pin) microcontroller with 4 kB OTP
The 87LPC764 is a 20-pin single-chip microcontroller designed for low pin count applications demanding high-integration, low cost
solutions over a wide range of performance requirements. A member of the Philips low pin count family, the 87LPC764 offers
programmable oscillator configurations for high and low speed crystals or RC operation, wide operating voltage range, programmable port
output configurations, selectable Schmitt trigger inputs, LED drive outputs, and a built-in watchdog timer. The 87LPC764 is based on an
accelerated 80C51 processor architecture that executes instructions at twice the rate of standard 80C51 devices.
lAn accelerated 80C51 CPU provides instruction cycle times of 300-600 ns for all instructions except multiply and divide when
executing at 20 MHz. Execution at up to 20 MHz when VDD = 4.5 V to 6.0 V, 10 MHz when VDD = 2.7 V to 6.0 V.
l2.7 V to 6.0 V operating range for digital functions.
l4 K bytes EPROM code memory.
l128 byte RAM data memory.
l32-byte customer code EPROM allows serialization of devices, storage of setup parameters, etc.
lTwo 16-bit counter/timers. Each timer may be configured to toggle a port output upon timer overflow.
lTwo analog comparators.
lFull duplex UART.
lI²C communication port.
lEight keypad interrupt inputs, plus two additional external interrupt inputs.
lFour interrupt priority levels.
lWatchdog timer with separate on-chip oscillator, requiring no external components. The watchdog timeout time is selectable from 8
values.
lActive low reset. On-chip power-on reset allows operation with no external reset components.
lLow voltage reset. One of two preset low voltage levels may be selected to allow a graceful system shutdown when power fails. May
optionally be configured as an interrupt.
• Description
• Features
• Datasheet
• Products, packages, availability and ordering
• Find similar products
•
To be kept informed on 87LPC764,
subscribe to eNews.
Subscribe
to eNews
Description
Features
lOscillator Fail Detect. The watchdog timer has a separate fully on-chip oscillator, allowing it to perform an oscillator fail detect
function.
lConfigurable on-
chip oscillator with frequency range and RC oscillator options (selected by user programmed EPROM bits). The RC
oscillator option allows operation with no external oscillator components.
lProgrammable port output configuration options: quasi-bidirectional, open drain, push-pull, input-only.
lSelectable Schmitt trigger port inputs.
lLED drive capability (20 mA) on all port pins.
lControlled slew rate port outputs to reduce EMI. Outputs have approximately 10 ns minimum ramp times.
l15 I/O pins minimum. Up to 18 I/O pins using on-chip oscillator and reset options.
lOnly power and ground connections are required to operate the 87LPC764 when fully on-chip oscillator and reset options are
selected.
lSerial EPROM programming allows simple in-circuit production coding. Two EPROM security bits prevent reading of sensitive
application programs.
lIdle and Power Down reduced power modes. Improved wakeup from Power Down mode (a low interrupt input starts execution).
Typical Power Down current is 1 µA.
l20-pin DIP and SO packages.
Please read information about some discontinued variants of this product.
Datasheet
Type nr. Title Publication
release date Datasheet status Page
count
File
size
(kB) Datasheet
87LPC764 Low power, low price, low pin count
(20 pin) microcontroller with 4 kB OTP 01-Jun-00 Preliminary
Specification 55 274 Download
Products, packages, availability and ordering
Partnumber North American
Partnumber Order code
(12nc) marking/packing package device status buy online
P87LPC764BD P87LPC764BD 9352 633 58512 Standard Marking * Tube Dry
Pack SOT163 Full production
P87LPC764BN P87LPC764BN 9352 633 59112 Standard Marking * Tube SOT146 Full production
P87LPC764FD 9352 668 44512 Standard Marking * Tube Dry
Pack SOT163 Full production -
P87LPC764FN 9352 668 45112 Standard Marking * Tube SOT146 Full production -
Find similar products:
87LPC764 links to the similar products page containing an overview of products that are similar in function or related to the part
number(s) as listed on this page. The similar products page includes products from the same catalog tree(s) , relevant selection guides and
products from the same functional category.
Copyright © 2000
Royal Philips Electronics
All rights reserved.
Terms and conditions.
