0. QMIN | SSUE REVISIONS DRAWN DATE GASKET CORRECTED THE PIN ASSIGNMENT OF CN3. NN FX, | (CORRECTED THE MISDESCRIPTION) S.SANO| JUN. 2408 Ea VIEWING DIRECTION | ADDED THE STRUCTURE AND AREA DEFINITION ANGLE OF LEAST INVERSION TTS e/g" [Z] CASE _OF CUSTOMER (0.26) 78.48(1TTS OUTLINE) 1 | CN1 PIN ASSIGNMENT A\ (2.16) /A\74.68(TTS INSULATION) NO] SYMBOL [NO [SYMBOL (3.1) 72. 8(BEZEL OPENING) ! ACTIVE AREA_| |_INSULATION AREA iPRL 21{DB10 (3.76) 71.48(1TS KEY AREA) @4 420-4 2{ 1B 22|DB9 C4 as) 50 OR(ACTIVE AREA) A\STRUCTURE AND AREA DEFINI TION(S=NTS) 3(DOTCLK |23/DB8 (30 5) 4[VSYNC [24|]GND 1 5 [HSYNC_|25/DB7 6 [ENABLE |26|DB6 Oo i A 7(DB23 |27|DB5 | $20(R,6,B)x240 DOTS ! ala) 4. HU 8(DB22 |28|DB4 | | | Li] 2) =| 9(DB21_ |29/DB3 I i! Y||r}| Zz ! t |< Z| <| = 10(DB20 |[30/DB2 | q >) ay Spe 11/DB19 [31/DB1 Mcp yall | ZO) Bl Bl 12|DB18__|32|DBO - HW ] | S| wy] 13/DB17__|33/SDI | SLE] N) BE) 9 14[DB16 [34/SCL ! ! a| 3) =| 2) =] = 15[GND | 35{CS ! t o| lal wl ol @ H 16[DB15__|36/RESET | ! | ol lst a] 17[DB14__|37[SDO | YD | POP J) 1] O) 18(DB13_[38/GND > SSS SS ! ce r 19|DB12. [39/vcc a 20|DB11_[40|VCC _ =~ NPONEN LY ] CN2 PIN ASSIGNMENT 5 salalahe NO] SYMBOL [NO [SYMBOL AREA N}O} | 3]2] GS] COMPONENT AREA CONTACT SIDE T[LED-A | 3[LED-K N 2 00} 00] ~] <=] r9} SI 3h) Al 1 2 [NC ~ CN3 | q z (N3 ZXCN3 PIN ASSIGNMENT = CN2 a 1. SMAX CN2 (EL00:6240 SERIES) (ELCO:B227 SERIES) NO JS TMBOL | NO} SYMBOL Ni COMPONENT ATCUT (ELCO:6298 SERIES) Tfyu 3/YD (12.76) (5) 2(XL 4/XR (29.25) (20.5) (70.5) (2) er _ ye Of a __ | o | Ch g Lo wo 2 lc > ain AY ft Zz Ryo fd T My - S| UE . 7 Oo. 39-03 breathy ) T ) tS a nH |e LED-K | I} NC 40 1 - yo YU |i hi | 40-0.35 4 1 HLL nN LED-A 4-wo.65 |_|I| XL XR Th 2 Wo oo O29 0.3 1 P1x3=3 nm CN N - 520.1 vo _ DETAIL CN1(S=5:1) 1.3./ 4 co} DETAIL CN3(S=5:1) 0.2 | O.5 if 0.5 OT MATERIALS =SdFINISHSS 220-1 TOLERANCE DATE THIRD ANGLE Piel DETAIL CN2(S=5:1) MEASURE | A B | 2008/06/26 PROJECTION OPTREX CORPORATION Slehofe L<16 [40.1] #0.3]%1 | APPROVED y+} TITLE CNS 16<L<63 | +).2 | #0.5| #\1.5 | Noboru Wada SCALE] UNIT | DIMENSIONAL OUTLINE NOTE 63<L 250] +0,3 | +0.8| +A | CHECKED 1:1] mm |DWG NO(CODE) TTS CIRCUIT DIAGRAM THE DIMENSIONS WITH THE MARK(@) ARE CONTROLED [250<ts500[#0'5 [27.2[+3\ | Yasuo Yamaguchi [DATE apR.2208| _ T-55349AE BASE AS A PARTICULAR CHARACTERISTIC. 500<L #0.8[ 42 | +4 \ [DRAWN DSGN DWG SIZE DWG REV ANGLE +1 \| 5 | +10\| Satoshi Sano S.Sano AS