Enpirion(R) Power Datasheet EN6337QI 3A PowerSoC Voltage Mode Synchronous PWM Buck with Integrated Inductor Description Features The EN6337QI is a Power System on a Chip (PowerSoC) DC-DC converter. It integrates MOSFET switches, small-signal circuits, compensation, and the inductor in an advanced 4mm x 7mm x 1.85mm 38pin QFN package. * * * * * * * * * * The EN6337QI is specifically designed to meet the precise voltage and fast transient requirements of present and future high-performance, low-power processor, DSP, FPGA, memory boards and system level applications in distributed power architecture. The device's advanced circuit techniques, ultra high switching frequency, and proprietary integrated inductor technology deliver high-quality, ultra compact, non-isolated DC-DC conversion. The Altera Enpirion power solution significantly helps in system design and productivity by offering greatly simplified board design, layout and manufacturing requirements. In addition, a reduction in the number of vendors required for the complete power solution helps to enable an overall system cost savings. All Enpirion products are RoHS compliant and leadfree manufacturing environment compatible. EN6337QI 90 RA VFB 47F 1206 PGND LLM/ SS AGND SYNC 80 CA 1206 PGND Efficiency vs. Output Current 100 RB CSS EFFICIENCY (%) 22F * Point of Load Regulation for Low-Power, ASICs Multi-Core and Communication Processors, DSPs, FPGAs and Distributed Power Architectures * Blade Servers, RAID Storage and LAN/SAN Adapter Cards, Wireless Base Stations, Industrial Automation, Test and Measurement, Embedded Computing, and Printers * High Efficiency 12V Intermediate Bus Architectures * Beat Frequency/Noise Sensitive Applications VOUT ENABLE AVIN Applications VOUT VIN PVIN Integrated Inductor, MOSFETs, Controller Up to 3A Continuous Operating Current High Efficiency (Up to 95%) Frequency Synchronization to External Clock Input Voltage Range (2.5V to 6.6V) Programmable Light Load Mode Optimized Total Solution Size (75mm2) Output Enable Pin and Power OK Programmable Soft-Start Thermal Shutdown, Over-Current, Short Circuit, and Under-Voltage Protection * RoHS Compliant, MSL Level 3, 260C Reflow Actual Solution Size 70 60 75mm2 PWM 50 40 30 20 VOUT = 2.5V LLM 10 VOUT = 2.5V PWM 0 0.01 Figure 1. Simplified Applications Circuit LLM CONDITIONS VIN = 3.3V 0.1 1 OUTPUT CURRENT (A) 10 Figure 2. Highest Efficiency in Smallest Solution Size www.altera.com/enpirion 05800 June 26, 2015 Rev E EN6337QI Ordering Information Part Number EN6337QI EVB-EN6337QI Package Markings EN6337QI EN6337QI T A (C) -40 to +85 Package Description 38-pin (4mm x 7mm x 1.85mm) QFN T&R QFN Evaluation Board Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html RLLM POK ENABLE LLM / SYNC 29 28 27 26 KEEP OUT VFB SS AGND 32 30 AVIN 33 31 NC(SW) NC(SW) NC(SW) 36 34 NC(SW) 37 35 NC(SW) 12 13 14 15 16 17 18 19 NC(SW) PGND PGND PGND PGND PGND PGND PVIN 6 11 VOUT VOUT 5 9 VOUT KEEP OUT 10 4 VOUT 3 NC 39 PGND VOUT NC 8 2 VOUT NC(SW) 7 1 VOUT NC(SW) 38 Pin Assignments (Top View) 25 NC 24 NC 23 NC 22 NC 21 PVIN 20 PVIN Figure 3: Pin Out Diagram (Top View) NOTE A: NC pins are not to be electrically connected to each other or to any external signal, ground, or voltage. However, they must be soldered to the PCB. Failure to follow this guideline may result in part malfunction or damage. NOTE B: Shaded area highlights exposed metal below the package that is not to be mechanically or electrically connected to the PCB. Refer to Figure 11 for details. NOTE C: White `dot' on top left is pin 1 indicator on top of the device package. Pin Description PIN NAME 1-2, 12, 34-38 NC(SW) 3-4, 2225 NC 5-11 VOUT 13-18 PGND 19-21 PVIN 26 LLM/ SYNC 27 ENABLE FUNCTION NO CONNECT - These pins are internally connected to the common switching node of the internal MOSFETs. They are not to be electrically connected to any external signal, ground, or voltage. Failure to follow this guideline may result in damage to the device. NO CONNECT - These pins may be internally connected. Do not connect to each other or to any other electrical signal. Failure to follow this guideline may result in device damage. Regulated converter output. Connect these pins to the load and place output capacitor between these pins and PGND pins 13-15. Input/Output power ground. Connect these pins to the ground electrode of the input and output filter capacitors. See VOUT and PVIN pin descriptions for more details. Input power supply. Connect to input power supply. Decouple with input capacitor to PGND pins 16-18. Dual function pin providing LLM Enable and External Clock Synchronization (see Application Section). At static Logic HIGH, device will allow automatic engagement of light load mode. At static logic LOW, the device is forced into PWM only. A clocked input to this pin will synchronize the internal switching frequency to the external signal. If this pin is left floating, it will pull to a static logic high, enabling LLM. Input Enable. Applying logic high enables the output and initiates a soft-start. Applying logic low disables the output. www.altera.com/enpirion, Page 2 05800 June 26, 2015 Rev E EN6337QI PIN NAME 28 POK 29 RLLM 30 SS 31 VFB 32 AGND 33 AVIN 39 PGND FUNCTION Power OK is an open drain transistor used for power system state indication. POK is logic high when VOUT is within -10% of VOUT nominal. Programmable LLM engage resistor to AGND allows for adjustment of load current at which Light-Load Mode engages. Can be left open for PWM only operation. Soft-Start node. The soft-start capacitor is connected between this pin and AGND. The value of this capacitor determines the startup time. External Feedback Input. The feedback loop is closed through this pin. A voltage divider at VOUT is used to set the output voltage. The midpoint of the divider is connected to VFB. A phase lead capacitor from this pin to VOUT is also required to stabilize the loop. Analog Ground. This is the controller ground return. Connect to a quiet ground. Input power supply for the controller. Connect to input voltage at a quiet point. Device thermal pad to be connected to the system GND plane. See Layout Recommendations section. Absolute Maximum Ratings CAUTION: Absolute Maximum ratings are stress ratings only. Functional operation beyond the recommended operating conditions is not implied. Stress beyond the absolute maximum ratings may impair device life. Exposure to absolute maximum rated conditions for extended periods may affect device reliability. PARAMETER SYMBOL MIN MAX UNITS Voltages on : PVIN, AVIN, VOUT -0.3 7.0 V Voltages on: ENABLE, POK, LLM/SYNC -0.3 V IN +0.3 V Voltages on: VFB, SS, RLLM -0.3 2.5 V -65 150 C 150 C Reflow Temp, 10 Sec, MSL3 JEDEC J-STD-020A 260 C ESD Rating (based on Human Body Model) 2000 V ESD Rating (based on CDM) 500 V Storage Temperature Range T STG Maximum Operating Junction Temperature T J-ABS Max Recommended Operating Conditions PARAMETER SYMBOL MIN MAX UNITS V IN 2.5 6.6 V Output Voltage Range (Note 1) V OUT 0.75 V IN - V DO V Output Current I OUT 3 A Input Voltage Range Operating Ambient Temperature TA -40 +85 C Operating Junction Temperature TJ -40 +125 C Thermal Characteristics PARAMETER SYMBOL TYP UNITS Thermal Shutdown T SD 160 C Thermal Shutdown Hysteresis T SDH 35 C Thermal Resistance: Junction to Ambient (0 LFM) (Note 2) JA 30 C/W Thermal Resistance: Junction to Case (0 LFM) JC 3 C/W Note 1: V DO (dropout voltage) is defined as (I LOAD x Droput Resistance). Please refer to Electrical Characteristics Table. Note 2: Based on 2oz. external copper layers and proper thermal design in line with EIJ/JEDEC JESD51-7 standard for high thermal conductivity boards. www.altera.com/enpirion, Page 3 05800 June 26, 2015 Rev E EN6337QI Electrical Characteristics NOTE: V IN =6.6V, Minimum and Maximum values are over operating ambient temperature range unless otherwise noted. Typical values are at T A = 25C. PARAMETER SYMBOL Operating Input Voltage TEST CONDITIONS V IN Under Voltage Lockout - V IN Rising V UVLOR Voltage above which UVLO is not asserted Under Voltage Lockout - V IN Falling V UVLOF Voltage below which UVLO is asserted Shut-Down Supply Current IS Operating Quiescent Current MIN TYP 2.5 MAX UNITS 6.6 V 2.3 V 2.075 V ENABLE=0V 100 A IQ LLM/SYNC = High 650 A V FB Feedback node voltage at: VIN = 5V, ILOAD = 0, TA = 25C (Note 6) 0.7425 0.75 0.7575 V V VFB 0A I LOAD 3A Starting Date Code: X501 or higher 0.739 0.75 0.761 V Feedback Pin Voltage (Line, Load, Temperature) V FB Feedback node voltage at: 2.5V VIN 6.6V 0A ILOAD 3A 0.735 0.75 0.765 V Feedback pin Input Leakage Current (Note 3) I FB VFB pin input leakage current -5 5 nA V OUT Rise Time (Note 3) t RISE Measured from when V IN > V UVLOR & ENABLE pin voltage crosses its logic high threshold to when V OUT reaches its final value. C SS = 15 nF 0.9 1.5 ms Soft Start Capacitor Range C SS_RANGE 68 nF Output Drop Out Voltage Resistance (Note 3) V DO R DO V INMIN - V OUT at Full load Input to Output Resistance 315 105 mV m Continuous Output Current I OUT PWM mode LLM mode (Note 4) 3 3 A Over Current Trip Level I OCP V IN = 5V, V OUT = 1.2V Disable Threshold V DISABLE ENABLE pin logic low. 0.0 0.6 V ENABLE Threshold V ENABLE ENABLE pin logic high 2.5V V IN 6.6V 1.8 V IN V ENABLE Lockout Time T ENLOCKOUT ENABLE pin Input Current (Note 3) I ENABLE Switching Frequency (Free Running) External SYNC Clock Frequency Lock Range Feedback Pin Voltage VFB Pin Voltage (Load and Temperature) 1.2 10 210 70 0 0.002 5 A 4.2 ms ENABLE pin has ~180k pull down 40 A F SW Free Running frequency of oscillator 1.9 MHz F PLL_LOCK Range of SYNC clock frequency 1.5 2.3 MHz www.altera.com/enpirion, Page 4 05800 June 26, 2015 Rev E EN6337QI PARAMETER SYMBOL TEST CONDITIONS SYNC Input Threshold - Low (LLM/SYNC PIN) V SYNC_LO SYNC Clock Logic Level SYNC Input Threshold - High (LLM/SYNC PIN) (Note 5) V SYNC_HI SYNC Clock Logic Level POK Lower Threshold POK LT Output voltage as a fraction of expected output voltage POK Output low Voltage V POKL With 4mA current sink into POK 0.4 V POK Output Hi Voltage V POKH 2.5V V IN 6.6V V IN V POK pin V OH leakage current (Note 3) I POKL POK high 1 A LLM Logic Low (LLM/SYNC PIN) V LLM_LO LLM Static Logic Level LLM Logic High (LLM/SYNC PIN) V LLM_HI LLM Static Logic Level LLM/SYNC Pin is <2.5V TYP 1.8 MAX UNITS 0.8 V 2.5 V 90 Minimum VIN-VOUT to ensure proper LLM operation LLM Engage Headroom LLM/SYNC Pin Current MIN % 800 mV 0.3 1.5 V V <100 nA Note 3: Parameter not production tested but is guaranteed by design. Note 4: LLM operation is only guaranteed above the minimum specified output current. Note 5: For proper operation of the synchronization circuit, the high-level amplitude of the SYNC signal should not be above 2.5V. Note 6: The VFB pin is a sensitive node. Do not touch VFB while the device is in regulation. www.altera.com/enpirion, Page 5 05800 June 26, 2015 Rev E EN6337QI Typical Performance Curves PWM Efficiency vs. IOUT (VIN = 5.0V) 100 90 90 80 80 EFFICIENCY (%) EFFICIENCY (%) PWM Efficiency vs. IOUT (VIN = 3.3V) 100 70 60 50 VOUT = 2.5V 40 VOUT = 1.8V 30 VOUT = 1.5V 20 CONDITIONS VIN = 3.3V 10 70 60 VOUT = 3.3V 50 VOUT = 2.5V 40 VOUT = 1.8V 30 VOUT = 1.2V 20 VOUT = 1.0V 10 VOUT = 1.5V 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 0 3 LLM Efficiency vs. IOUT (VIN = 3.3V) 100 90 90 80 80 70 60 50 VOUT = 2.5V 40 VOUT = 1.8V 30 VOUT = 1.5V 20 CONDITIONS VIN = 3.3V 10 0 0.01 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 70 60 VOUT = 3.3V 50 VOUT = 2.5V 40 VOUT = 1.8V 30 VOUT = 1.2V 20 VOUT = 1.0V 10 0.1 1 OUTPUT CURRENT (A) 0.5 LLM Efficiency vs. IOUT (VIN = 5.0V) 100 EFFICIENCY (%) EFFICIENCY (%) VOUT = 1.0V 0 0 VOUT = 1.5V 10 VOUT = 1.2V CONDITIONS VIN = 5V 0 0.01 VOUT = 1.0V 1 0.1 OUTPUT CURRENT (A) 10 Output Voltage vs. Output Current Output Voltage vs. Output Current 1.220 1.015 VIN = 5.0V 1.010 VIN = 3.3V OUTPUT VOLTAGE (V) 1.020 OUTPUT VOLTAGE (V) VOUT = 1.2V CONDITIONS VIN = 5V 1.005 1.000 0.995 0.990 CONDITIONS VOUT = 1.0V 0.985 1.215 VIN = 5.0V 1.210 VIN = 3.3V 1.205 1.200 1.195 1.190 CONDITIONS VOUT = 1.2V 1.185 0.980 1.180 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 www.altera.com/enpirion, Page 6 05800 June 26, 2015 Rev E EN6337QI Typical Performance Curves (Continued) Output Voltage vs. Output Current Output Voltage vs. Output Current 1.820 1.515 VIN = 5.0V 1.510 VIN = 3.3V OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 1.520 1.505 1.500 1.495 1.490 CONDITIONS VOUT = 1.5V 1.485 1.815 VIN = 5.0V 1.810 VIN = 3.3V 1.805 1.800 1.795 1.790 1.480 1.780 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 0 Output Voltage vs. Output Current 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 3.320 2.515 VIN = 5.0V 2.510 VIN = 3.3V 3.315 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) 0.5 Output Voltage vs. Output Current 2.520 2.505 2.500 2.495 2.490 CONDITIONS VOUT = 2.5V 2.485 VIN = 5.0V 3.310 3.305 3.300 3.295 3.290 CONDITIONS VOUT = 3.3V 3.285 3.280 2.480 0 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 0 3 1.820 1.815 1.815 OUTPUT VOLTAGE (V) 1.820 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 0A 1.785 0.5 1 1.5 2 OUTPUT CURRENT (A) 2.5 3 Output Voltage vs. Input Voltage Output Voltage vs. Input Voltage OUTPUT VOLTAGE (V) CONDITIONS VOUT = 1.8V 1.785 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 1A 1.785 1.780 1.780 2.4 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 6.6 2.4 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 6.6 www.altera.com/enpirion, Page 7 05800 June 26, 2015 Rev E EN6337QI Typical Performance Curves (Continued) Output Voltage vs. Input Voltage 1.820 1.815 1.815 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) Output Voltage vs. Input Voltage 1.820 1.810 1.805 1.800 1.795 1.790 CONDITIONS Load = 2A A 1.785 1.810 1.805 1.800 1.795 1.790 1.780 1.780 2.4 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 2.4 6.6 100.0 4.5 90.0 4 80.0 LEVEL (dBV/m) 5 3.5 3 2.5 2 1.5 CONDITIONS Conditions VIN VIN == 5.0V 5.0V VOUT VOUT = 3.3V = 3.3V 1 0.5 3 3.6 4.2 4.8 5.4 INPUT VOLTAGE (V) 6 6.6 EMI Performance (Horizontal Scan) No Thermal Derating GUARANTEED OUTPUT CURRENT (A) CONDITIONS Load = 3A A 1.785 CONDITIONS VIN = 5.0V VOUT_NOM = 1.5V LOAD = 0.5 70.0 60.0 50.0 CISPR 22 Class B 3m 40.0 30.0 20.0 10.0 0 -40 -15 10 35 60 AMBIENT TEMPERATURE( C) 85 30 300 FREQUENCY (MHz) EMI Performance (Vertical Scan) 100.0 CONDITIONS VIN = 5.0V VOUT_NOM = 1.5V LOAD = 0.5 90.0 LEVEL (dBV/m) 80.0 70.0 60.0 50.0 CISPR 22 Class B 3m 40.0 30.0 20.0 10.0 30 300 FREQUENCY (MHz) www.altera.com/enpirion, Page 8 05800 June 26, 2015 Rev E EN6337QI Typical Performance Characteristics Output Ripple at 20MHz Bandwidth Output Ripple at 500MHz Bandwidth VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 3.3V VOUT = 1V IOUT = 3A CIN = 22F (1206) COUT = 47 F (1206) + 10F (0805) CONDITIONS VIN = 3.3V VOUT = 1V IOUT = 3A CIN = 22F (1206) COUT = 47 F (1206) + 10F (0805) Output Ripple at 20MHz Bandwidth Output Ripple at 500MHz Bandwidth VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 5V VOUT = 1V IOUT = 3A CIN = 22F (1206) COUT = 47 F (1206) + 10F (0805) CONDITIONS VIN = 5V VOUT = 1V IOUT = 3A CIN = 22F (1206) COUT = 47 F (1206) + 10F (0805) LLM Output Ripple at 100mA LLM Output Ripple at 100mA VOUT (AC Coupled) VOUT (AC Coupled) CONDITIONS VIN = 5V VOUT = 1V IOUT = 100mA CIN = 22F (1206) COUT = 2 x 47 F (1206) CONDITIONS VIN = 3.3V VOUT = 1V IOUT = 100mA CIN = 22F (1206) COUT = 2 x 47 F (1206) www.altera.com/enpirion, Page 9 05800 June 26, 2015 Rev E EN6337QI Typical Performance Characteristics (Continued) Enable Power Up/Down Enable Power Up/Down ENABLE ENABLE VOUT POK LOAD VOUT POK CONDITIONS VIN = 5.5V, VOUT = 3.3V NO LOAD, Css = 15nF CIN = 22F (1206) COUT = 47 F (1206) LLM Load Transient from 0.01 to 3A VOUT (AC Coupled) LOAD LLM Load Transient from 0.01 to 3A VOUT (AC Coupled) CONDITIONS LLM = ENABLED VIN = 5V VOUT = 1V CIN = 2 x 22F (1206) COUT = 2 x 47F (1206) LOAD PWM Load Transient from 0 to 3A CONDITIONS LLM = ENABLED VIN = 5V VOUT = 3V CIN = 2 x 22F (1206) COUT = 2 x 47F (1206) PWM Load Transient from 0 to 3A VOUT (AC Coupled) LOAD CONDITIONS VIN = 5.5V, VOUT = 3.3V LOAD=1.1, Css = 15nF CIN = 22F (1206) COUT = 47 F (1206) LOAD VOUT (AC Coupled) CONDITIONS LLM = DISABLED VIN = 5V VOUT = 1V CIN = 2 x 22F (1206) COUT = 2 x 47F (1206) LOAD CONDITIONS LLM = DISABLED VIN = 5V VOUT = 3V CIN = 2 x 22F (1206) COUT = 2 x 47F (1206) www.altera.com/enpirion, Page 10 05800 June 26, 2015 Rev E EN6337QI Functional Block Diagram RLLM PVIN UVLO Thermal Limit P-Drive Current Limit NC(SW) Mode Logic VOUT N-Drive (-) PWM Comp (+) LLM/SYNC PGND Compensation Network PLL/Sawtooth Generator (-) Error Amp (+) ENABLE SS VFB Power Good Logic POK AVIN Soft Start Voltage Reference Regulated Voltage AGND Figure 4: Functional Block Diagram www.altera.com/enpirion, Page 11 05800 June 26, 2015 Rev E EN6337QI Functional Description Synchronous Buck Converter The EN6337QI is a synchronous, programmable power supply with integrated power MOSFET switches and integrated inductor. The nominal input voltage range is 2.5V to 6.6V. The output voltage is programmed using an external resistor divider network. The control loop is voltage-mode with a type III compensation network. Much of the compensation circuitry is internal to the device. However, a phase lead capacitor is required along with the output voltage feedback resistor divider to complete the type III compensation network. The device uses a low-noise PWM topology and also integrates a unique light-load mode (LLM) to improve efficiency at light output load currents. LLM can be disabled with a logic pin. Up to 3A of continuous output current can be drawn from this converter. The 2 MHz switching frequency allows the use of small size input / output capacitors, and enables wide loop bandwidth within a small foot print. Protection Features: The power supply has the following protection features: * Over-current protection (to protect the IC from excessive load current) * Thermal shutdown with hysteresis. * Under-voltage lockout circuit to keep the converter output off while the input voltage is less than 2.3V. Additional Features: * The switching frequency can be phaselocked to an external clock to eliminate or move beat frequency tones out of band. * Soft-start circuit allowing controlled startup when the converter is initially powered up. The soft start time is programmable with an appropriate choice of soft start capacitor. * Power good circuit indicating the output voltage is greater than 90% of programmed value as long as feedback loop is closed. * To maintain high efficiency at low output current, the device incorporates automatic light load mode operation. Enable Operation The ENABLE pin provides a means to enable normal operation or to shut down the device. When the ENABLE pin is asserted (high) the device will undergo a normal soft start. A logic low on this pin will power the device down in a controlled manner. From the moment ENABLE goes low, there is a fixed lock out time before the output will respond to the ENABLE pin reasserted (high). This lock out is activated for even very short logic low pulses on the ENABLE pin. The ENABLE signal must be pulled high at a slew rate faster than 1V/5s in order to meet startup time specifications; otherwise, the device may experience a delay of ~4.2ms (lock-out time) before startup occurs. See the Electrical Characteristics Table for technical specifications for this pin. LLM/SYNC Pin This is a dual function pin providing LLM Enable and External Clock Synchronization. At static Logic HIGH, device will allow automatic engagement of light load mode. At static logic LOW, the device is forced into PWM only. A clocked input to this pin will synchronize the internal switching frequency - LLM mode is not available if this input is clocked. If this pin is left floating, it will pull to a static logic high, enabling LLM. Frequency Synchronization The switching frequency of the DC/DC converter can be phase-locked to an external clock source to move unwanted beat frequencies out of band. To avail this feature, the clock source should be connected to the LLM/SYNC pin. An activity detector recognizes the presence of an external clock signal and automatically phase-locks the internal oscillator to this external clock. Phase-lock will occur as long as the clock frequency is in the range specified in the Electrical Characteristics Table. For proper operation of the synchronization circuit, the high-level amplitude of the SYNC www.altera.com/enpirion, Page 12 05800 June 26, 2015 Rev E EN6337QI signal should not be above 2.5V. Please note LLM is not available when synchronizing to an external frequency. Spread Spectrum Mode The external clock frequency may be swept between the limits specified in the Electrical Characteristics Table at repetition rates of up to 10 kHz in order to reduce EMI frequency components. Soft-Start Operation During Soft-start, the output voltage is ramped up gradually upon start-up. The output rise time is controlled by the choice of soft-start capacitor, which is placed between the SS pin (30) and the AGND pin (32). Rise Time: T R (C SS * 80k) 25% During start-up of the converter, the reference voltage to the error amplifier is linearly increased to its final level by an internal current source of approximately 10uA. Typical softstart rise time is ~1.2mS with SS capacitor value of 15nF. The rise time is measured from when V IN > V UVLOR and ENABLE pin voltage crosses its logic high threshold to when V OUT reaches its programmed value. Please note LLM function is disabled during the soft-start ramp-up time. POK Operation The POK signal is an open drain signal (requires a pull up resistor to V IN or similar voltage) from the converter indicating the output voltage is within the specified range. The POK signal will be logic high (V IN ) when the output voltage is above 90% of programmed V OUT . If the output voltage goes below this threshold, the POK signal will be logic low. Light Load Mode (LLM) Operation The EN6337QI uses a proprietary light load mode to provide high efficiency at low output currents. When the LLM/SYNC pin is high, the device is in automatic LLM "Detection" mode. When the LLM/SYNC pin is low, the device is forced into PWM mode. In automatic LLM "Detection" mode, when a light load condition is detected, the device will: (1) Step V OUT up by approximately 1.0% above the nominal operating output voltage setting, V NOM and as low as -0.5% below V NOM , and then (2) Shut down unnecessary circuitry, and then (3) Monitor V OUT . When V OUT falls below V NOM , the device will repeat (1), (2), and (3). The voltage step up, or pre-positioning, improves transient droop when a load transient causes a transition from LLM mode to PWM mode. If a load transient occurs, causing V OUT to fall below the threshold V MIN , the device will exit LLM operation and begin normal PWM operation. Figure 5 demonstrates V OUT behavior during transition into and out of LLM operation. LLM Ripple VMAX PWM Ripple VNOM VOUT VMIN Load Step IOUT Figure 5: V OUT behavior in LLM operation. Many multi-mode DCDC converters suffer from a condition that occurs when the load current increases only slowly so that there is no load transient driving V OUT below the V MIN threshold. In this condition, the device would never exit LLM operation. This could adversely affect efficiency and cause unwanted ripple. To prevent this from occurring, the EN6337QI periodically exits LLM mode into PWM mode and measures the load current. If the load current is above the LLM threshold current, the device will remain in PWM mode. If the load current is below the LLM threshold, the device will re-enter LLM operation. There may be a small overshoot or undershoot in V OUT when the device exits and re-enters LLM. The load current at which the device will enter LLM mode is a function of input and output voltage, and the RLLM pin resistor. For PWM www.altera.com/enpirion, Page 13 05800 June 26, 2015 Rev E EN6337QI only operation, the RLLM pin can be left open. LLM to PWM Current vs. RLLM LLM TO PWM CURRENT (A) 2.000 VIN = 5V, VOUT = 3.3V 1.800 VIN = 3.3V, VOUT = 2.5V 1.600 VIN = 5V, VOUT = 1V 1.400 VIN = 3.3V, VOUT = 1V 1.200 CONDITIONS TA = 25C Typical Values 1.000 0.800 cycle. If the over-current condition is removed, the over-current protection circuit will enable normal PWM operation. If the over-current condition persists, the soft start capacitor will gradually discharge causing the output voltage to fall. When the OCP fault is removed, the output voltage will ramp back up to the desired voltage. This circuit is designed to provide high noise immunity. 0.600 Thermal Overload Protection 0.400 Thermal shutdown circuit will disable device operation when the Junction temperature exceeds approximately 150C. After a thermal shutdown event, when the junction temperature drops by approximately 20C, the converter will re-start with a normal soft-start. 0.200 0.000 0 10 20 30 40 50 60 70 RLLM RESISTOR (k) 80 90 100 Figure 6. Typical LLM to PWM Current vs. RLLM To ensure normal LLM operation, LLM mode should be enabled and disabled with specific sequencing. For applications with explicit LLM pin control, enable LLM after V IN ramp up is complete. For applications with only ENABLE control, tie LLM to ENABLE; enable the device after V IN ramp up is complete, and disable the device before VIN ramp down begins. For designs with ENABLE and LLM tied to V IN , make sure the device soft-start time is longer than the V IN ramp-up time. LLM will start operating after the soft-start time is completed. NOTE: For proper LLM operation the EN6337QI requires a minimum difference between V IN and V OUT , and a minimum LLM load requirement as specified in the Electrical Characteristics Table. Over-Current Protection The current limit function is achieved by sensing the current flowing through the Power PFET. When the sensed current exceeds the over current trip point, both power FETs are turned off for the remainder of the switching Input Under-Voltage Lock-Out Internal circuits ensure that the converter will not start switching until the input voltage is above the specified minimum voltage. Hysteresis and input de-glitch circuits ensure high noise immunity and prevent false UVLO triggers. Compensation The EN6337QI uses a Type III voltage mode control compensation network. As noted earlier, a piece of the compensation network is the phase lead capacitor CA in Figure 7. This network is optimized for use with about 50100F of output capacitance and will provide wide loop bandwidth and excellent transient performance for most applications. Voltage mode operation provides high noise immunity at light load. In some applications, modifications to the compensation may be required. Refer to the Application Information section for more details. Application Information The EN6337QI output voltage is programmed using a simple resistor divider network. Since VFB is a sensitive node, do not touch the VFB node while the device is in operation as doing so may introduce parasitic capacitance into the control loop that causes the device to behave abnormally and damage may occur. Figure 7 shows the resistor divider configuration. www.altera.com/enpirion, Page 14 05800 June 26, 2015 Rev E EN6337QI series inductance, ESL: VOUT Z = ESR + ESL RA CA = 15 pF Placing output capacitors in parallel reduces the impedance and will hence result in lower PWM ripple voltage. In addition, higher output capacitance will improve overall regulation and ripple in light-load mode. 1 1 1 1 = + + ... + Z Total Z 1 Z 2 Zn VFB RB RA = 200 k RB = 0.75 * RA (VOUT - 0.75 V ) Figure 7: V OUT Resistor Divider & Compensation Capacitor Typical PWM Ripple Voltages An additional compensation capacitor C A is also required in parallel with the upper resistor. Input Capacitor Selection The EN6337QI requires about 20uF of input capacitance. Low-cost, low-ESR ceramic capacitors should be used as input capacitors for this converter. The dielectric must be X5R or X7R rated. Y5V or equivalent dielectric formulations must not be used as these lose too much capacitance with frequency, temperature and bias voltage. In some applications, lower value capacitors are needed in parallel with the larger, capacitors in order to provide high frequency decoupling. Recommended Input Capacitors Description 10 F, 10V, 10% X7R, 1206 (2 capacitors needed) 22 F, 10V, 20% X5R, 1206 (1 capacitor needed) MFG Output Capacitor Configuration Typical Output Ripple (mVp-p) (as measured on EN6337QI Evaluation Board)* 1 x 47 F 25 47 F + 10 F 14 Table 2 Typical PWM Ripple Voltages * Note: 20 MHz BW limit Recommended Output Capacitors Description MFG 47uF, 6.3V, 20% X5R, 1206 (1 or 2 capacitors needed) 10uF, 10V, 10% X5R, 1206 (Optional 1 capacitor in parallel with 47uF above) P/N Murata GRM31CR60J476ME19L Taiyo Yuden JMK316BJ476ML-T Murata GRM31CR71A106KA01L Taiyo Yuden LMK316BJ226ML-T Table 3 Recommended Output Capacitors P/N Murata GRM31CR71A106KA01L Taiyo Yuden LMK316B7106KL-T Murata GRM31CR61A226ME19L Taiyo Yuden LMK316BJ226ML-T Table 1 Recommended Input Capacitors Output Capacitor Selection The EN6337QI has been nominally optimized for use with approximately 50-100F of output capacitance. Low ESR ceramic capacitors are required with X5R or X7R rated dielectric formulation. Y5V or equivalent dielectric formulations must not be used as these lose too much capacitance with frequency, temperature and bias voltage. Output ripple voltage is determined by the aggregate output capacitor impedance. Output impedance, denoted as Z, is comprised of effective series resistance, ESR, and effective For best LLM performance, we recommend using just 2x47uF capacitors mentioned in the above table, and no 10uF capacitor. The V OUT sense point should be just after the last output filter capacitor right next to the device. Additional bulk output capacitance beyond the above recommendations can be used on the output node of the EN6337QI as long as the bulk capacitors are far enough from the V OUT sense point such that they do not interfere with the control loop operation. In some cases modifications to the compensation or output filter capacitance may be required to optimize device performance such as transient response, ripple, or hold-up time. The EN6337QI provides the capability to modify the control loop response to allow for customization for such applications. Note that in Type III Voltage Mode Control, the double pole of the output filter is around 1/ www.altera.com/enpirion, Page 15 05800 June 26, 2015 Rev E EN6337QI 2LO Cout , where C out is the equivalent capacitance of all the output capacitors including the minimum required output capacitors that Altera recommended and the extra bulk capacitors customers added based on their design requirement. While the compensation network was designed based on the capacitors that Altera recommended, increasing the output capacitance will shift the double pole to the direction of lower frequency, which will lower the loop bandwidth and phase margin. In most cases, this will not cause the instability due to adequate phase margin already in the design. In order to maintain a higher bandwidth as well as adequate phase margin, a slight modification of the external compensation is necessary. This can be easily implemented by increasing the leading capacitor value, Ca. In addition the ESR of the output capacitors also helps since the ESR and output capacitance forms a zero which also helps to boost the phase. COUT Range (F) Ca (pF) Minimum ESR (m) 100 200 300 400 500 800 1000 15 22 27 33 39 47 56 0 0 0 0 0 >4 >4 Table 4 Bulk Capacitance Compensation Power-Up During power-up, ENABLE should not be asserted before PVIN, and PVIN should not be asserted before AVIN. Tying all three pins together meets these requirements. The EN6337QI supports startup into a prebiased output of up to 1.5V. The output of the EN6337QI can be pre-biased with a voltage up to 1.5V when it is first enabled. www.altera.com/enpirion, Page 16 05800 June 26, 2015 Rev E EN6337QI Thermal Considerations Thermal considerations are important power supply design facts that cannot be avoided in the real world. Whenever there are power losses in a system, the heat that is generated by the power dissipation needs to be accounted for. The Enpirion PowerSoC helps alleviate some of those concerns. The Enpirion EN6337QI DC-DC converter is packaged in a 4x7x3mm 38-pin QFN package. The QFN package is constructed with copper lead frames that have exposed thermal pads. The exposed thermal pad on the package should be soldered directly on to a copper ground pad on the printed circuit board (PCB) to act as a heat sink. The recommended maximum junction temperature for continuous operation is 125C. Continuous operation above 125C may reduce long-term reliability. The device has a thermal overload protection circuit designed to turn off the device at an approximate junction temperature value of 160C. The following example and calculations illustrate the thermal performance of the EN6337QI. = P OUT / P IN = 92.5% = 0.925 P IN = P OUT / P IN 9.9W / 0.925 10.7W The power dissipation (P D ) is the power loss in the system and can be calculated by subtracting the output power from the input power. P D = P IN - P OUT 10.7W - 9.9W 0.8W With the power dissipation known, the temperature rise in the device may be estimated based on the theta JA value ( JA ). The JA parameter estimates how much the temperature will rise in the device for every watt of power dissipation. The EN6337QI has a JA value of 30 C/W without airflow. Determine the change in temperature (T) based on P D and JA . T = P D x JA T 0.8W x 30C/W = 24.08C 24C V IN = 5V The junction temperature (T J ) of the device is approximately the ambient temperature (T A ) plus the change in temperature. We assume the initial ambient temperature to be 25C. V OUT = 3.3V T J = T A + T I OUT = 3A T J 25C + 24C 49C First calculate the output power. The maximum operating junction temperature (T JMAX ) of the device is 125C, so the device can operate at a higher ambient temperature. The maximum ambient temperature (T AMAX ) allowed can be calculated. Example: P OUT = 3.3V x 3A = 9.9W Next, determine the input power based on the efficiency () shown in Figure 8. T AMAX = T JMAX - P D x JA Efficiency vs. IOUT (VOUT = 3.3V) 125C - 24C 101C 100 90 EFFICIENCY (%) The maximum ambient temperature the device can reach is 101C given the input and output conditions. Note that the efficiency will be slightly lower at higher temperatures and this calculation is an estimate. LLM 80 70 60 50 PWM 40 CONDITIONS VIN = 5V 30 VOUT = 3.3V LLM 20 VOUT = 3.3V PWM 10 0 0.01 0.1 1 OUTPUT CURRENT (A) 10 Figure 8: Efficiency vs. Output Current For V IN = 5V, V OUT = 3.3V at 3A, 92.5% www.altera.com/enpirion, Page 17 05800 June 26, 2015 Rev E EN6337QI Engineering Schematic Figure 9: Engineering Schematic with Engineering Notes www.altera.com/enpirion, Page 18 05800 June 26, 2015 Rev E EN6337QI Layout Recommendation Figure 10 shows critical components and layer 1 traces of a recommended minimum footprint EN6337QI layout with ENABLE tied to V IN in PWM mode. Alternate ENABLE configurations, and other small signal pins need to be connected and routed according to specific customer application. Please see the Gerber files on the Altera website www.altera.com/enpirion for exact dimensions and other layers. Please refer to this Figure while reading the layout recommendations in this section. Recommendation 1: Input and output filter capacitors should be placed on the same side of the PCB, and as close to the EN6337QI package as possible. They should be connected to the device with very short and wide traces. Do not use thermal reliefs or spokes when connecting the capacitor pads to the respective nodes. The +V and GND traces between the capacitors and the EN6337QI should be as close to each other as possible so that the gap between the two nodes is minimized, even under the capacitors. Recommendation 2: Three PGND pins are dedicated to the input circuit, and three to the output circuit. The slit in Figure 10 separating the input and output GND circuits helps minimize noise coupling between the converter input and output switching loops. Recommendation 3: The system ground plane should be the first layer immediately below the surface layer. This ground plane should be continuous and un-interrupted below the converter and the input/output capacitors. Please see the Gerber files on the Altera website www.altera.com/enpirion. Recommendation 4: The large thermal pad underneath the component must be connected to the system ground plane through as many vias as possible. Figure 10: Top PCB Layer Critical Components and Copper for Minimum Footprint The drill diameter of the vias should be 0.33mm, and the vias must have at least 1 oz. copper plating on the inside wall, making the finished hole size around 0.20-0.26mm. Do not use thermal reliefs or spokes to connect the vias to the ground plane. This connection provides the path for heat dissipation from the converter. Please see Figures: 7, 8, and 9. Recommendation 5: Multiple small vias (the same size as the thermal vias discussed in recommendation 4 should be used to connect ground terminal of the input capacitor and output capacitors to the system ground plane. It is preferred to put these vias under the capacitors along the edge of the GND copper closest to the +V copper. Please see Figure 10. These vias connect the input/output filter capacitors to the GND plane, and help reduce parasitic inductances in the input and output current loops. If the vias cannot be placed under C IN and C OUT , then put them just outside the capacitors along the GND slit separating the two components. Do not use thermal reliefs or spokes to connect these vias to the ground plane. Recommendation 6: AVIN is the power supply for the internal small-signal control circuits. It should be connected to the input voltage at a quiet point. In Figure 10 this connection is made at the input capacitor close to the V IN connection. www.altera.com/enpirion, Page 19 05800 June 26, 2015 Rev E EN6337QI Recommendation 7: The layer 1 metal under the device must not be more than shown in Figure 10. See the section regarding exposed metal on bottom of package. As with any switch-mode DC/DC converter, try not to run sensitive signal or control lines underneath the converter package on other layers. Recommendation 8: The V OUT sense point should be just after the last output filter capacitor. Keep the sense trace as short as possible in order to avoid noise coupling into the control loop. Recommendation 9: Keep R A , C A , and R B close to the VFB pin (see Figures 6 and 7). The VFB pin is a high-impedance, sensitive node. Keep the trace to this pin as short as possible. Whenever possible, connect R B directly to the AGND pin instead of going through the GND plane. www.altera.com/enpirion, Page 20 05800 June 26, 2015 Rev E EN6337QI Design Considerations for Lead-Frame Based Modules Exposed Metal on Bottom of Package Lead-frames offer many advantages in thermal performance, in reduced electrical lead resistance, and in overall foot print. However, they do require some special considerations. In the assembly process lead frame construction requires that, for mechanical support, some of the lead-frame cantilevers be exposed at the point where wire-bond or internal passives are attached. This results in several small pads being exposed on the bottom of the package, as shown in Figure 11. Only the thermal pad and the perimeter pads are to be mechanically or electrically connected to the PC board. The PCB top layer under the EN6337QI should be clear of any metal (copper pours, traces, or vias) except for the thermal pad. The "shaded-out" area in Figure 11 represents the area that should be clear of any metal on the top layer of the PCB. Any layer 1 metal under the shaded-out area runs the risk of undesirable shorted connections even if it is covered by soldermask. The solder stencil aperture should be smaller than the PCB ground pad. This will prevent excess solder from causing bridging between adjacent pins or other exposed metal under the package. Figure 11: Lead-Frame exposed metal (Bottom View) Shaded area highlights exposed metal that is not to be mechanically or electrically connected to the PCB. www.altera.com/enpirion, Page 21 05800 June 26, 2015 Rev E EN6337QI Recommended PCB Footprint Figure 12: EN6337QI PCB Footprint (Top View) The solder stencil aperture for the thermal pad is shown in blue and is based on Enpirion power product manufacturing specifications. www.altera.com/enpirion, Page 22 05800 June 26, 2015 Rev E EN6337QI Package and Mechanical Figure 13: EN6337QI Package Dimensions (Bottom View) Packing and Marking Information: www.altera.com/support/reliability/packing/rel-packing-and-marking.html Contact Information Altera Corporation 101 Innovation Drive San Jose, CA 95134 Phone: 408-544-7000 www.altera.com (c) 2014 Altera Corporation--Confidential. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, HARDCOPY, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. www.altera.com/enpirion, Page 23 05800 June 26, 2015 Rev E Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Altera: EVB-EN6337QI