FEATURES FUNCTIONAL BLOCK DIAGRAM Schottky diode detector with linearization Broadband 50 input impedance Accurate response from 0.5 GHz to 43.5 GHz with minimal slope variation Input range of -30 dBm to +15 dBm, referred to 50 Excellent temperature stability 2.1 V/VPEAK (output voltage per input peak voltage) slope at 10 GHz Fast envelope bandwidth: 40 MHz Fast output rise time: 4 ns Low power consumption: 1.6 mA at 5.0 V 2 mm x 2 mm, 6-lead LFCSP package ADL6010 RFCM 4 RFIN 5 LINEARIZER RFCM 6 3 VPOS 2 VOUT 1 COMM 11617-001 Data Sheet Fast Responding, 45 dB Range, 0.5 GHz to 43.5 GHz Envelope Detector ADL6010 Figure 1. APPLICATIONS Microwave point to point links Microwave instrumentation Radar-based measurement systems GENERAL DESCRIPTION The ADL6010 is a versatile, broadband envelope detector covering the microwave spectrum. It provides state-of-theart accuracy with very low power consumption (8 mW) in a simple, easy to use 6-lead format. The output is a baseband voltage proportional to the instantaneous amplitude of the radio frequency (RF) input signal. It exhibits minimal slope variation of the RF input to envelope output transfer function from 0.5 GHz to 43.5 GHz. The detector cell uses a proprietary eight Schottky diode array followed by a novel linearizer circuit that creates a linear voltmeter with an overall scaling factor (or transfer gain) of nominally x2.2 relative to the voltage amplitude of the input. Although the ADL6010 is not inherently a power responding device, it remains convenient to specify the input in this way. Thus, the permissible input power, relative to a 50 source input impedance, ranges from -30 dBm to +15 dBm. The corresponding input voltage amplitudes of 11.2 mV to 1.8 V generate quasi-dc outputs from about 25 mV to 4 V above common (COMM). Rev. D A subtle aspect of the balanced detector topology is that no even-order distortion, caused by nonlinear source loading, occurs at the input. This is an important benefit in applications where a low ratio coupler is used to extract a signal sample and is a significant improvement over traditional diode detectors. The power equivalent of a fluctuating RF input amplitude can be extracted by the addition of an rms-to-dc converter IC. Alternatively, the baseband output can be applied to a suitably fast analog-to-digital converter (ADC) and the rms value (and other signal metrics, such as peak to average ratio) calculated in the digital domain. The output response accuracy is insensitive to variation in the supply voltage, which can range from 4.75 V to 5.25 V. The ultralow power dissipation contributes to its long-term stability. The ADL6010ACPZN is specified for operation from -40C to +85C, and the ADL6010SCPZN is specified for operation from -55C to +125C. Both are available in a 6-lead, 2 mm x 2 mm LFCSP package. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2014-2019 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADL6010 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Measurement Setups ...................................................................... 15 Applications ....................................................................................... 1 Theory of Operation ...................................................................... 16 Functional Block Diagram .............................................................. 1 Basic Connections ...................................................................... 17 General Description ......................................................................... 1 PCB Layout Recommendations ............................................... 17 Revision History ............................................................................... 2 System Calibration and Error Calculation.............................. 17 Specifications..................................................................................... 3 Effect of a Capacitave Load on Rise Time and Fall Time ..... 19 Absolute Maximum Ratings............................................................ 7 Evaluation Board ............................................................................ 20 ESD Caution .................................................................................. 7 Evaluation Board Assembly Drawings .................................... 21 Pin Configuration and Function Descriptions ............................. 8 Outline Dimensions ....................................................................... 22 Typical Performance Characteristics ............................................. 9 Ordering Guide .......................................................................... 22 REVISION HISTORY 9/2019--Rev. C to Rev. D Changes to Ordering Guide .......................................................... 22 2/2019--Rev. B to Rev. C Changes to General Description Section ...................................... 1 Changes to Ordering Guide .......................................................... 22 Updated Outline Dimensions ....................................................... 22 6/2017--Rev. A to Rev. B Changes to Typical Performance Characteristics Section ...........9 Updated Outline Dimensions ....................................................... 22 Changes to Ordering Guide .......................................................... 22 9/2014--Rev. 0 to Rev. A Deleted Figure 3 and Figure 6; Renumbered Sequentially ..........9 Deleted Figure 39 and Changes to Theory of Operation Section... 16 7/2014--Revision 0: Initial Version Rev. D | Page 2 of 22 Data Sheet ADL6010 SPECIFICATIONS VPOS = 5.0 V, TA = 25C, 50 source input impedance, single-ended input drive, unless otherwise stated. Table 1. Parameter RF INPUT INTERFACE Operating Frequency Nominal Input Impedance FREQUENCY = 500 MHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 1 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 5 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage Test Conditions/Comments RFIN pin Min Typ 1 0.5 Max Unit 43.5 Single-ended input drive, see the Theory of Operation section Input RFIN to output VOUT 50 GHz Continuous wave (CW) input Three point calibration at -26 dBm, -14 dBm, and +5 dBm Three point calibration at -26 dBm, -14 dBm, and +5 dBm Deviation from output at 25C -40C < TA < +85C, input power (PIN) = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at -14 dBm and +5 dBm Calibration at -14 dBm and +5 dBm 44 16 -28 dB dBm dBm +0.2/-0.1 +0.3/-0.2 +0.7/-0,6 +0.9/-1.2 2.2 0.3 dB dB dB dB V/ VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 2.2 0.19 V V CW input Three point calibration at -25 dBm, -10 dBm, and +8 dBm Three point calibration at -25 dBm, -10 dBm, and +8 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -55C < TA < +125C, PIN = -10 dBm -40C < TA < +85C, PIN = -10 dBm Calibration at -10 dBm and +8 dBm Calibration at -10 dBm and +8 dBm 45 15 -30 dB dBm dBm +0.1/-0.1 +0.2/-0.2 +0.3/-0.3 +0.4/-0.6 2.2 0.5 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 2.25 0.22 V V CW input Three point calibration at -25 dBm, -10 dBm, and +8 dBm Three point calibration at -25 dBm, -10 dBm, and +8 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at -10 dBm and +8 dBm Calibration at -10 dBm and +8 dBm 46 16 -30 dB dBm dBm +0.2/-0.1 +0.3/-0.2 +0.2/-0.2 +0.3/-0.4 2.1 0.5 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm 2.2 0.22 V V Rev. D | Page 3 of 22 ADL6010 Parameter FREQUENCY = 10 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 15 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 20 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage Data Sheet Test Conditions/Comments Input RFIN to output VOUT Min Typ 1 Max Unit CW input Three point calibration at -28 dBm, -10 dBm, and +10 dBm Three point calibration at -28 dBm, -10 dBm, and +10 dBm Deviation from output at 25C -40C < TA < +85C, PIN = 10 dBm -55C < TA < +125C, PIN = 10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at -10 dBm and +10 dBm Calibration at -10 dBm and +10 dBm 46 16 -30 dB dBm dBm +0.2/-0.1 +0.4/-0.2 +0.2/-0.2 +0.4/-0.4 2.1 0.6 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 2.1 0.22 V V CW input Three point calibration at -28 dBm, -10 dBm, and +10 dBm Three point calibration at -28 dBm, -10 dBm, and +10 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm 47 16 -30 dB dBm dBm +0.2/-0.2 +0.3/-0.3 +0.2/-0.3 +0.3/-0.6 dB dB dB dB Calibration at -10 dBm and +10 dBm Calibration at -10 dBm and +10 dBm 2.1 0.6 V/VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 2.1 0.22 V V CW input Three point calibration at -28 dBm, -10 dBm, and +8 dBm Three point calibration at -28 dBm, -10 dBm, and +8 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at -10 dBm and +8 dBm Calibration at -10 dBm and +8 dBm 46 15 -30 dB dBm dBm +0.2/-0.2 +0.3/-0.4 +0.2/-0.3 +0.3/-0.6 2.2 0.55 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm 2.3 0.246 V V Rev. D | Page 4 of 22 Data Sheet Parameter FREQUENCY = 25 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 30 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 35 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage ADL6010 Test Conditions/Comments Input RFIN to output VOUT CW input Three point calibration at -28 dBm, -10 dBm, and +8 dBm Three point calibration at -28 dBm, -10 dBm, and +8 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at -14 dBm and +10 dBm Calibration at -14 dBm and +10 dBm Min Typ 1 Max Unit 46 15 -30 dB dBm dBm +0.2/-0.2 +0.3/-0.4 +0.2/-0.4 +0.3/-0.7 2.3 0.55 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 2.36 0.242 V V CW input Three point calibration at -26 dBm, 0 dBm, and +10 dBm Three point calibration at -26 dBm, 0 dBm, and +10 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at 0 dBm and +10 dBm Calibration at 0 dBm and +10 dBm 45 16 -29 dB dBm dBm +0.3/-0.2 +0.4/-0.4 +0.5/-0.5 +0.6/-0.8 2.3 0.6 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 2.2 0.21 V V CW input Three point calibration at -25 dBm, 0 dBm, and +10 dBm Three point calibration at -25 dBm, 0 dBm, and +10 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at 0 dBm and 10 dBm Calibration at 0 dBm and 10 dBm 44 15 -29 dB dBm dBm +0.4/-0.4 +0.5/-0.6 +0.5/-0.5 +0.6/-1.6 2.4 0.6 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm 2.3 0.198 V V Rev. D | Page 5 of 22 ADL6010 Parameter FREQUENCY = 40 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage FREQUENCY = 43.5 GHz Detection Range 1 dB Error Maximum Input Level, 1 dB Minimum Input Level, 1 dB Deviation vs. Temperature Slope Intercept Output Voltage OUTPUT INTERFACE DC Output Resistance Output Offset Maximum Output Voltage Available Output Current Rise Time Fall Time Envelope Bandwidth POWER SUPPLIES Supply Voltage Quiescent Current 1 Data Sheet Test Conditions/Comments Input RFIN to output VOUT Min Typ 1 Max Unit CW input Three point calibration at -20 dBm, 0 dBm, and +10 dBm Three point calibration at -20 dBm, 0 dBm, and +10 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at 0 dBm and 10 dBm Calibration at 0 dBm and 10 dBm 42 17 -25 dB dBm dBm +0.2/-0.2 +0.3/-0.3 +0.5/-0.5 +0.6/-0.9 1.7 0.4 dB dB dB dB V/VPEAK V PIN = +10 dBm PIN = -10 dBm Input RFIN to output VOUT 1.64 0.135 V V CW input Three point calibration at -20 dBm, 0 dBm, and +10 dBm Three point calibration at -20 dBm, 0 dBm, and +10 dBm Deviation from output at 25C -40C < TA < +85C, PIN = +10 dBm -55C < TA < +125C, PIN = +10 dBm -40C < TA < +85C, PIN = -10 dBm -55C < TA < +125C, PIN = -10 dBm Calibration at 0 dBm and 10 dBm Calibration at 0 dBm and 10 dBm 41 17 -24 dB dBm dBm +0.6/-0.4 +0.7/-0.7 +0.7/-0.5 +0.8/-1.1 1.6 0.35 dB dB dB dB V/VPEAK V 1.46 0.118 V V <5 4 4.3 5/0.3 mV V mA 4 50 40 ns ns MHz PIN = +10 dBm PIN = -10 dBm Pin VOUT PIN = off TA = 25C, VPOS = 5.0 V, PIN = 19 dBm Sourcing/sinking PIN = off to 0 dBm, 10% to 90%, CLOAD = 10 pF ,RSERIES = 100 PIN = off to 0 dBm, 10% to 90%, CLOAD = 10 pF, RSERIES = 100 3 dB bandwidth Pin VPOS 4.75 TA = 25C, no signal at RFIN, VPOS = 5.0 V -40C < TA < +85C -55C < TA < +125C Slashes in the typical (typ) column indicate a range. For example, -0.2/+0.1 means -0.2 to +0.1. Rev. D | Page 6 of 22 5.0 1.6 2.0 2.2 5.25 V mA mA mA Data Sheet ADL6010 ABSOLUTE MAXIMUM RATINGS Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. Table 2. Parameter Supply Voltage, VPOS Input RF Power1 Equivalent Voltage, Sine Wave Input Internal Power Dissipation JC2 JA2 JT2 JB2 Maximum Junction Temperature Operating Temperature Range ADL6010ACPZN-R7 ADL6010SCPZN-R7 Storage Temperature Range Lead Temperature (Soldering 60 sec) 1 2 Rating 5.5 V 20 dBm 3.16 V 20 mW 16.4C/W 82.9C/W 0.6C/W 49.3C/W 150C ESD CAUTION -40C < TA < +85C -55C < TA < +125C -65C to +150C 300C Driven from a 50 source. No airflow when the exposed pad soldered to a 4-layer JEDEC board. Rev. D | Page 7 of 22 ADL6010 Data Sheet PIN CONFIGURATION AND FUNCTION DESCRIPTIONS ADL6010 RFCM 4 3 VPOS RFIN 5 2 VOUT RFCM 6 1 COMM NOTES 1. EXPOSED PAD. THE EXPOSED PAD (EPAD) ON THE UNDERSIDE OF THE DEVICE IS ALSO INTERNALLY CONNECTED TO GROUND AND REQUIRES GOOD THERMAL AND ELECTRICAL CONNECTION TO THE GROUND OF THE PRINTED CIRCUIT BOARD (PCB). CONNECT ALL GROUND PINS TO A LOW IMPEDANCE GROUND PLANE TOGETHER WITH THE EPAD. 11617-002 TOP VIEW (Not to Scale) Figure 2. Pin Configuration Table 3. Pin Function Descriptions Pin No. 1 Mnemonic COMM 2 3 VOUT VPOS 4, 6 RFCM 5 RFIN EPAD Description Device Ground. Connect COMM to the system ground using a low impedance ground plane together with the exposed pad (EPAD). Output Voltage. The output from the VOUT pin is proportional to the envelope value at the RFIN pin. Supply Voltage. The operational range is from 4.75 V to 5.25 V. Decouple the power supply using the suggested capacitor values of 100 pF and 0.1 F and locate these capacitors as close as possible to the VPOS pin. Device Grounds. Connect the RFCM pins to the system ground using a low impedance ground plane together with the exposed pad (EPAD). Signal Input. The RFIN pin is ac-coupled and has an RF input impedance of approximately 50 . Exposed Pad. The exposed pad (EPAD) on the underside of the device is also internally connected to ground and requires good thermal and electrical connection to the ground of the printed circuit board (PCB). Connect all ground pins to a low impedance ground plane together with the EPAD. Rev. D | Page 8 of 22 Data Sheet ADL6010 TYPICAL PERFORMANCE CHARACTERISTICS VPOS = 5.0 V, CLOAD = open, TA = 25C, unless otherwise specified. Error referred to slope and intercept at indicated calibration points. Single-ended input drive, input RF signal is a continuous sine wave, unless otherwise noted. 5 2.6 SUPPLY CURRENT (mA) 3 2 VPOS = 4.75V VPOS = 5.00V VPOS = 5.25V 2.4 +125C 2.2 +85C 2.0 +25C 1.8 -40C 1.6 1 -55C 11617-004 1.4 0 -40 -35 -30 -25 -20 -15 -10 0 -5 5 10 1.2 -40 -35 -30 -25 -20 -15 -10 20 15 11617-005 OUTPUT VOLTAGE (V) 4 -5 5 0 10 15 20 PIN (dBm) PIN (dBm) Figure 3. Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Supply Voltages Figure 6. Supply Current vs. RF Input Power (PIN) for Various Temperatures 0 1 0 -1 NORMALIZED GAIN (dB) -10 -15 -2 -3 -4 -5 5 10 15 20 25 30 35 11617-008 -20 0.5 11617-007 -6 -7 -8 0.1 40 1 FREQUENCY (GHz) 10 4 4 10 CALIBRATION AT -26dBm, -14dBm, AND +5dBm CALIBRATION AT -26dBm, -14dBm, AND +5dBm 3 1 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 0.1 0 OUTPUT VOLTAGE (V) 1 2 0.01 1 1 0 0.1 -1 -55C -40C +25C +85C +125C -2 -3 OUTPUT VOLTAGE (V) 3 2 0.01 -3 -25 -20 -15 -10 -5 0 5 10 15 0.001 20 PIN (dBm) Figure 5. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 0.5 GHz -4 -30 11617-009 ERROR (dB) 100 Figure 7. Envelope Bandwidth of VOUT vs. Frequency at PIN = -10 dBm and Modulation Depth = 10% (See Figure 36 in the Measurement Setups Section) Figure 4. Input Return Loss (S11) vs. Input Frequency with Input Connector and PCB Trace Embedded -4 -30 10 FREQUENCY (MHz) -25 -20 -15 -10 0 -5 PIN (dBm) 5 10 15 0.001 20 11617-012 S11 (dB) -5 Figure 8. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 0.5 GHz Rev. D | Page 9 of 22 ADL6010 Data Sheet 10 4 4 10 CALIBRATION AT -25dBm, -10dBm, AND +8dBm CALIBRATION AT -25dBm, -10dBm, AND +8dBm 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 1 2 OUTPUT VOLTAGE (V) 1 0 0.1 -1 -55C -40C +25C +85C +125C -2 0.01 -3 -20 -15 -10 -5 0 5 10 15 0.001 20 -4 -30 0 -5 PIN (dBm) 5 10 15 0.001 20 10 2 0.1 0 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 1 OUTPUT VOLTAGE (V) 1 1 1 0 0.1 -1 -55C -40C +25C +85C +125C -2 0.01 OUTPUT VOLTAGE (V) 3 2 0.01 -3 -20 -15 -10 -5 0 5 10 15 0.001 20 -4 -30 11617-011 -25 PIN (dBm) -20 -15 -10 -5 0 PIN (dBm) 5 10 15 0.001 20 Figure 13. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 5 GHz Figure 10. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 5 GHz 10 4 -25 11617-014 -3 10 4 CALIBRATION AT -28dBm, -10dBm, AND +10dBm CALIBRATION AT -28dBm, -10dBm, AND +10dBm 3 3 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 1 1 2 OUTPUT VOLTAGE (V) 2 0.01 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 -3 OUTPUT VOLTAGE (V) ERROR (dB) -10 CALIBRATION AT -25dBm, -10dBm, AND +8dBm 3 0.01 -3 -25 -20 -15 -10 -5 0 5 10 15 0.001 20 PIN (dBm) Figure 11. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 10 GHz 11617-015 ERROR (dB) -15 4 10 CALIBRATION AT -25dBm, -10dBm, AND +8dBm -4 -30 -20 Figure 12. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 1 GHz Figure 9. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 1 GHz 4 -25 11617-013 -25 PIN (dBm) -4 -30 0.01 -3 11617-010 -4 -30 1 -4 -30 -25 -20 -15 -10 -5 PIN (dBm) 0 5 10 15 0.001 20 11617-018 ERROR (dB) 2 OUTPUT VOLTAGE (V) 3 3 Figure 14. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 10 GHz Rev. D | Page 10 of 22 Data Sheet ADL6010 10 4 10 4 CALIBRATION AT -28dBm, -10dBm, AND +10dBm CALIBRATION AT -28dBm, -10dBm, AND +10dBm 3 3 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 0.1 0 OUTPUT VOLTAGE (V) 0.1 0 -1 -55C -40C +25C +85C +125C -2 0.01 -3 -20 -15 -10 -5 0 5 10 15 0.001 20 -4 -30 Figure 15. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 15 GHz -5 0 5 10 15 0.001 20 10 CALIBRATION AT -28dBm, -10dBm, AND +8dBm 3 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 0.1 0 OUTPUT VOLTAGE (V) 1 1 2 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 0.01 OUTPUT VOLTAGE (V) 1 2 0.01 -3 -20 -15 -10 -5 0 5 10 15 0.001 20 -4 -30 11617-017 -25 PIN (dBm) Figure 16. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 20 GHz -20 -15 -10 -5 0 5 10 15 0.001 20 PIN (dBm) Figure 19. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 20 GHz 10 4 -25 11617-020 -3 10 4 CALIBRATION AT -28dBm, -10dBm, AND +8dBm CALIBRATION AT -28dBm, -10dBm, AND +8dBm 3 3 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 1 1 2 OUTPUT VOLTAGE (V) 2 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 0.01 -3 OUTPUT VOLTAGE (V) ERROR (dB) -10 4 3 0.01 -3 -25 -20 -15 -10 -5 0 5 10 15 0.001 20 PIN (dBm) Figure 17. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 25 GHz 11617-021 ERROR (dB) -15 Figure 18. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 15 GHz CALIBRATION AT -28dBm, -10dBm, AND +8dBm -4 -30 -20 PIN (dBm) 10 4 -25 11617-019 -25 PIN (dBm) -4 -30 0.01 -3 11617-016 -4 -30 1 -4 -30 -25 -20 -15 -10 -5 PIN (dBm) 0 5 10 15 0.001 20 11617-024 ERROR (dB) 1 1 2 OUTPUT VOLTAGE (V) 1 2 Figure 20. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 25 GHz Rev. D | Page 11 of 22 ADL6010 Data Sheet 10 4 4 10 CALIBRATION AT -26dBm, 0dBm, AND +10dBm CALIBRATION AT -26dBm, 0dBm, AND +10dBm 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 1 2 OUTPUT VOLTAGE (V) 1 0 0.1 -1 -55C -40C +25C +85C +125C -2 0.01 -3 -20 -15 -10 -5 0 5 10 15 0.001 20 -4 -30 -20 10 5 0.001 20 15 10 2 -1 -55C -40C +25C +85C +125C -2 1 1 0 0.1 -1 -55C -40C +25C +85C +125C -2 0.01 -3 -3 -20 -15 -10 -5 0 5 10 15 0.001 20 -4 -30 11617-023 -25 PIN (dBm) -20 -15 -10 -5 0 PIN (dBm) 5 10 15 0.001 20 Figure 25. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 35 GHz Figure 22. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 35 GHz 10 4 10 4 -25 0.01 11617-026 0.1 0 ERROR (dB) 1 OUTPUT VOLTAGE (V) 1 OUTPUT VOLTAGE (V) 3 2 CALIBRATION AT -20dBm, 0dBm, AND +10dBm CALIBRATION AT -20dBm, 0dBm, AND +10dBm 3 3 -1 -55C -40C +25C +85C +125C -2 ERROR (dB) 0.1 0 OUTPUT VOLTAGE (V) 1 1 2 1 2 1 0.1 0 -1 -55C -40C +25C +85C +125C -2 0.01 OUTPUT VOLTAGE (V) ERROR (dB) 0 -5 PIN (dBm) CALIBRATION AT -25dBm, 0dBm, AND +10dBm 3 0.01 -3 -3 -25 -20 -15 -10 -5 0 5 10 15 0.001 20 PIN (dBm) 11617-027 ERROR (dB) -10 4 10 CALIBRATION AT -25dBm, 0dBm, AND +10dBm -4 -30 -15 Figure 24. Distribution of Conformance Error with Respect to Output Voltage (VOUT) at 25C vs. RF Input Power (PIN) for Various Temperatures at 30 GHz Figure 21. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 30 GHz 4 -25 11617-025 -25 PIN (dBm) -4 -30 0.01 -3 11617-022 -4 -30 1 -4 -30 -25 -20 -15 -10 -5 0 5 10 15 0.001 20 PIN (dBm) Figure 26. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 43.5 GHz Figure 23. Conformance Error and Output Voltage (VOUT) vs. RF Input Power (PIN) for Various Temperatures at 40 GHz Rev. D | Page 12 of 22 11617-030 ERROR (dB) 2 OUTPUT VOLTAGE (V) 3 3 Data Sheet ADL6010 5000 3500 REPRESENTS MORE THAN 11,000 PARTS REPRESENTS MORE THAN 11,000 PARTS 3000 4000 2500 COUNT COUNT 3000 2000 2000 1500 1000 1000 0 2 4 6 8 10 12 11617-031 11617-028 500 0 14 1.52 1.60 OFFSET (mV) 1.68 1.76 1.84 1.92 QUIESCENT CURRENT (mA) Figure 27. Distribution of VOUT Offset with No Applied PIN at 25C Figure 29. Distribution of Quiescent Current at 25C 5000 5000 REPRESENTS MORE THAN 11,000 PARTS REPRESENTS MORE THAN 11,000 PARTS 4000 3000 3000 2000 1000 1000 11617-029 2000 0 1.62 1.68 1.74 1.80 1.86 1.92 0 0.22 1.98 11617-032 COUNT COUNT 4000 0.23 0.24 0.25 0.26 0.27 0.28 OUTPUT VOLTAGE (V) OUTPUT VOLTAGE (V) Figure 28. Output Voltage (VOUT) Distribution, PIN = 9 dBm at 12 GHz, 25C Figure 30. Output Voltage (VOUT) Distribution, PIN = -9 dBm at 12 GHz, 25C Rev. D | Page 13 of 22 ADL6010 Data Sheet 3.0 3.0 1GHz BURST REFERENCE 1GHz BURST REFERENCE 2.5 2.0 OUTPUT VOLTAGE (V) +10dBm 1.5 1.0 2.0 +10dBm 1.5 1.0 0dBm 0dBm 0.5 11617-034 0.5 -10dBm -20dBm 0 0 0.01 0.02 0.03 0.04 0.05 0.06 TIME (s) 0.07 0.08 0.09 -10dBm -20dBm 0 0.80 0.10 VPOS PULSE 5 -5 -10 1.5 -15 1.0 0dBm -20 -10dBm 0 -25 -20dBm -0.5 0 0.5 1.0 1.5 2.0 2.5 TIME (s) 3.0 3.5 -30 4.0 11617-033 OUTPUT VOLTAGE (V) +10dBm SUPPLY VOLTAGE (V) 0 2.5 0.5 0.90 0.95 1.00 1.05 1.10 1.15 1.20 1.25 1.30 Figure 33. RF Burst Input Response, Falling Edge (see Figure 34 in the Measurement Setups Section) 10 3.5 2.0 0.85 TIME (s) Figure 31. RF Burst Input Response, Rising Edge (see Figure 34 in the Measurement Setups Section) 3.0 11617-035 OUTPUT VOLTAGE (V) 2.5 Figure 32. VPOS Turn-On Pulse Response (see Figure 35 in the Measurement Setups Section) Rev. D | Page 14 of 22 Data Sheet ADL6010 MEASUREMENT SETUPS RF OUT ADL6010 EVALUATION BOARD RFIN TEKTRONIX DIGITAL PHOSPHOR OSCILLOSCOPE TDS5104 PULSE IN VPOS AGILENT 33522A FUNCTION/ARBITRARY WAVEFORM GENERATOR RF SOURCE (CARRIER) VOUT HP E3631A POWER SUPPLY 11617-036 Figure 34. Hardware Configuration for Output Response to RF Burst Input Measurements ADL6010 PULSE IN VOUT VPOS TEKTRONIX DIGITAL PHOSPHOR OSCILLOSCOPE TDS5104 1M TRIGGER AD8017 ON UG-128 EVALUATION BOARD AGILENT 33522A FUNCTION/ARBITRARY WAVEFORM GENERATOR ADL5545 (RF GAIN BLOCK) DIRECTIONAL COUPLER RFIN +2 11617-038 CH1 CH2 DC CONTROL FET PROBE TEKTRONIX DIGITAL PHOSPHOR (2pF,1M) OSCILLOSCOPE TDS5104 EVALUATION BOARD VOUT Figure 36. Hardware Configuration for Envelope Output Response Measurement EVALUATION BOARD RFIN ADL5390 (RF VECTOR MULTIPLIER) ADL6010 CH2 RF OUT SPECTRUM ANALYZER REF -10dB 1M TRIGGER CH1 ROHDE & SCHWARZ SIGNAL GENERATOR SMR 40 RF SOURCE (MODULATION) Figure 35. Hardware Configuration for Output Response to Power Supply Gating Measurements Rev. D | Page 15 of 22 11617-037 ROHDE & SCHWARZ SIGNAL GENERATOR SMR 40 ADL6010 Data Sheet THEORY OF OPERATION The ADL6010 uses eight Schottky diodes in a novel two path detector topology. One path responds during the positive half cycles of the input, and the second responds during the negative half cycles of the input, thus achieving full wave rectification. This arrangement presents a constant input impedance throughout the full RF cycle, thereby preventing the reflection of evenorder distortion components back toward the source, which is a well-known limitation of the widely used traditional single Schottky diode detectors. The envelope voltage gain of the ADL6010 is nominally x2.2 V/VPEAK from 1 GHz to 35 GHz. This factor becomes 3.2 V/V when the input signal is specified as the rms voltage of a CW carrier. For example, a steady -30 dBm input generates a dc output voltage of 22.5 mV, at which level the output buffer is able to track the envelope. In fact, the sensitivity at ambient temperatures typically extends below -30 dBm. However, over the specified temperature range, the measurement error tends to increase at the bottom of the specified range. Eight diodes are arranged on the chip in such a way as to minimize the effect of chip stresses and temperature variations. They are biased by small keep alive currents chosen in a trade-off between the inherently low sensitivity of a diode detector and the need to preserve envelope bandwidth. Thus, the corner frequency of the front-end low-pass filtering is a weak function of the input level. At low input levels, the -3 dB corner frequency is at approximately 0.5 GHz. The overall envelope bandwidth is limited mainly by the subsequent linearizing and output circuitry. For large inputs, the voltage headroom in the signal processing stages limits the measurement range. Using a 5 V supply, the maximum signal is approximately 3.6 V p-p, corresponding to a power of 15 dBm, referenced to 50 . Therefore, the ADL6010 achieves a 45 dB dynamic range of high accuracy measurement. Note that, above 43.5 GHz, accuracy is limited by the package, PCB, and instrumentation. The RF input interface provides a broadband (flat) 50 termination without the need for external components. Although the input return loss inevitably degrades at very high frequencies, the slope of the transfer function holds near 2.2 V/VPEAK up to 35 GHz, owing to the voltage responding behavior of the ADL6010. At small input levels, all Schottky diode detectors exhibit an extremely weak response which approximates a square law characteristic (having zero slope at the origin). For large inputs, the response approaches a linear transfer function. In the ADL6010, this nonlinearity and variations in the response are corrected using proprietary circuitry having an equally shaped but inverse amplitude function, resulting in an overall envelope response that is linear across the whole span of input levels. The composite signal is buffered and presented at the output pin (VOUT). The transfer function relating the instantaneous RF voltage amplitude to the quasi-dc output is a scalar constant of a little over x2. This scalar constant is mainly determined by ratios of resistors, which are independent of temperature and process variations. Errors associated with the minuscule voltages generated by the Schottky front-end under low level conditions, and other errors in the nonlinear signal processing circuitry, are minimized by laser trimming, permitting accurate measurement of RF input voltages down to the millivolts level. An aspect of the linear in volts response is that the minimum VOUT is limited by the ability of the output stage to reach down to absolute zero (the potential on the COMM pin) when using a single positive supply. DC voltages at the input are blocked by an on-chip capacitor. The two ground pins (RFCM) on either side of RFIN (Pin 5) form part of an RF coplanar waveguide (CPW) launch into the detector. The RFCM pins must be connected to the signal ground. Give careful attention to the design of the PCB in this area. Rev. D | Page 16 of 22 Data Sheet ADL6010 BASIC CONNECTIONS SYSTEM CALIBRATION AND ERROR CALCULATION The basic connections are shown in Figure 37. A dc supply of nominally 5 V is required. The bypass capacitors (C1 and C2) provide supply decoupling for the output buffer. Place these capacitors as close as possible to the VPOS pin. The exposed pad is internally connected to the IC ground and must be soldered down to a low impedance ground on the PCB. A filter capacitor (CLOAD) and series resistor (R1) may be inserted to form a low-pass filter for the output envelope. Small CLOAD values allow a quicker response to an RF burst waveform, and high CLOAD values provide signal averaging and noise reduction. The measured transfer function of the ADL6010 at 10 GHz is shown in Figure 39. This plots both the conformance error and the output voltage vs. the input level at +25C, +85C, +125C, -40C, and -55C. Over the input level range from -30 dBm to +15 dBm, the output voltage varies from approximately 20 mV to 4.3 V. 4 3 0.1 0 -1 -55C -40C +25C +85C +125C ADL6010 3 LINEARIZER 5 RFIN 6 2 R1 100 -3 VOUT CLOAD (SEE TEXT) 1 -4 -30 11617-040 4 -2 RFCM COMM -20 -15 -10 -5 0 5 10 0.01 15 0.001 20 PIN (dBm) Figure 39. Conformance Error and Output Voltage vs. RF Input Power (PIN) for Various Temperatures (-55C, -40C, +25C, +85C, and +125C) at 10 GHz Using Two Point Calibration Figure 37. Basic Connections PCB LAYOUT RECOMMENDATIONS To achieve the highest measurement accuracy, perform calibration at the board level, as the IC scaling varies from device to device. Parasitic elements of the PCB such as coupling and radiation limit accuracy at very high frequencies. Ensure faithful power transmission from the connector to the internal circuit of the ADL6010. Microstrip and CPW are popular forms of transmission lines because of their ease of fabrication and low cost. In the ADL6010 evaluation board, a grounded CPW (GCPW) minimizes radiation effects and provides the maximum bandwidth by using two rows of grounding vias on both sides of the signal trace. Calibration begins by applying two or more known signal levels, VIN1 and VIN2, within the operating range of the IC, and noting the corresponding outputs, VOUT1 and VOUT2. From these measurements, the slope and intercept of the scaling is extracted. For a two point calibration, the calculations are as follows: Slope = (VOUT2 - VOUT1)/(VIN2 - VIN1) Figure 38 shows the PCB layout of the ADL6010 evaluation board in detail. Minimize air gaps between the vias to ensure reliable transmission. Because a certain minimum distance between two adjacent grounding vias in a single row is needed, adding a second row of grounding vias on both sides of the GCPW is recommended. In this way, a much smaller equivalent air gap between grounding vias is achieved, and better transmission is accomplished. GND -25 OUTPUT VOLTAGE (V) 1 11617-042 ERROR (dB) C2 0.1F 1 2 VPOS C1 100pF 10 CALIBRATION AT -20dBm AND +5dBm Intercept = VOUT1 - (Slope x VIN1) where: Each VIN is the equivalent peak input voltage to RFIN, at a 50 input impedance. Once the slope and intercept are calculated and stored, use the following simple equations to calculate the unknown input power: VIN_CALCULATED = (VOUT (MEASURED) - Intercept)/Slope VIAS PIN_CALCULATED (dBm) = 10log10(1000 x (VIN_CALCULATED/2)2/50) The conformance error is RFIN PAD Figure 38. ADL6010 Evaluation Board 11617-041 Error (dB) = PIN_CALCULATED (dBm) - PIN_IDEAL (dBm) Figure 39 includes a plot of this error at -55C, -40C, +25C, +85C, and +125C when using a two point calibration with inputs at +5 dBm and -20 dBm. The relative error at these two calibration points is equal to 0 dB by definition. Rev. D | Page 17 of 22 ADL6010 Data Sheet 10 4 CALIBRATION AT -28dBm, -10dBm, AND +10dBm 3 1 0.1 0 -1 -55C -40C +25C +85C +125C 10 4 CALIBRATION AT -28dBm, -10dBm, AND +10dBm -2 3 -3 -3 -25 -20 -15 -10 -5 PIN (dBm) 0 5 10 0.001 20 -10 -5 0 5 10 15 0.001 20 11617-044 -15 PIN (dBm) Figure 41. 10 GHz Conformance Error and Output Voltage vs. RF Input Power (PIN) for Second Device at +25C, -40C, -55C, +85C, and +125C 0.01 15 -20 Figure 40. Conformance Error and Output Voltage vs. RF Input Power (PIN) and Temperature (-55C, -40C, +25C, +85C, +125C) at 10 GHz Using Three Point Calibration For the device shown in Figure 40, the change in error with temperature is very small over the upper 25 dB of the measurement range, being 0.4 dB, and widens at lower power levels, reaching 0.9 dB over the -10 dBm to -20 dBm segment. High volume production samples may perform better. For comparison, the three point calibration of a second device is shown in Figure 41 using the same frequency and calibration points. This sample has greater dynamic range, and the temperature dependence of error at lower power levels is inverted relative to the first device. Figure 42 shows the conformance error at 10 GHz for four devices at +25C, -40C, and +85C using a three point calibration at input levels of -28 dBm, -10 dBm, and +10 dBm. The error plots at each temperature were calculated with respect to the slope and intercept values extracted from the 25C line in each case. This calculation is consistent with a typical production scenario where calibration at only one temperature is used. Figure 42 illustrates the various error scenarios possible at low input levels. The dynamic range of the three point calibrated devices extends to -30 dBm for 1.0 dB error at 25C. 10 4 CALIBRATION AT -28dBm, -10dBm, AND +10dBm 3 1 2 1 0.1 0 -1 -40C +25C +85C -2 OUTPUT VOLTAGE (V) -55C -40C +25C +85C +125C -2 -25 0.01 -3 -4 -30 -25 -20 -15 -10 -5 PIN (dBm) 0 5 10 15 0.001 20 11617-045 -1 -4 -30 ERROR (dB) 0.1 0 OUTPUT VOLTAGE (V) 1 11617-043 ERROR (dB) 0.01 1 2 -4 -30 OUTPUT VOLTAGE (V) 1 2 ERROR (dB) Multipoint calibration can be used to further improve accuracy and extend the dynamic range. The transfer function is now broken into segments, with each having its own slope and intercept. Thus, Figure 40 shows the error plot of the same test device with calibration input points of -28 dBm, -10 dBm, and +10 dBm. The three point, dual slope calibration results in tighter error bounds over the high end of the range and extends the lower measurement range to -30 dBm for 1 dB error. Figure 42. 10 GHz Conformance Error and Output Voltage vs. RF Input Power (PIN) at +25C, +85C, and -40C for Multiple Devices Rev. D | Page 18 of 22 Data Sheet ADL6010 1000 In applications where the response bandwidth is fairly low, place a large shunt capacitor, CLOAD, directly on the VOUT pin. Figure 43 shows how rise time and fall time depend on CLOAD when the ADL6010 is driven by a square wave modulated RF input at a carrier frequency of 1 GHz. 100 10 FALL TIME (s) 90% TO 10% 1 RISE TIME (s) 10% TO 90% 0.1 0.01 0.001 0.01 11617-046 The ADL6010 can measure both the instantaneous envelope power and the average power of an RF signal. When VOUT is unloaded, the output follows the envelope of the input tracking bandwidths up to 40 MHz. By adding a simple RC circuit to the basic connections circuit as shown in Figure 37, the output signal can be averaged using single pole filtering. RISING TIME/FALLING TIME (s) EFFECT OF A CAPACITIVE LOAD ON RISE TIME AND FALL TIME 0.1 1 10 CLOAD (nF) 100 1000 Figure 43. Rising Time/Falling Time vs. CLOAD for a 1 GHz Modulated Pulsed Waveform with PIN = 0 dBm Rev. D | Page 19 of 22 ADL6010 Data Sheet EVALUATION BOARD The ADL6010-EVALZ is a fully populated, 4-layer, Rogers 4003-based evaluation board. For normal operation, it only requires a 5 V supply connected to VPOS and GND. The RF input signal is accepted at a high performance 2.92 mm connector (RFIN). The output voltage is available on the SMA connector (VOUT) or on the test loop (V_OUT). Configuration options for the evaluation board are listed in Table 4. VPOS C4 100pF R2 100 C2 DNI V_OUT ADL6010 RFIN 4 RFCM VPOS 3 5 RFIN VOUT 2 6 RFCM R1 100 COMM 1 PAD GND VOUT C1 DNI 11617-047 C3 0.1F Figure 44. ADL6010 Evaluation Board Schematic Table 4. Evaluation Board Configuration Options Component R1, R2 C1, C2 C3, C4 RFIN Function/Comments Output interfaces. Use a 100 series resistor when driving highly capacitive loads. R2 can be replaced with a 0 resistor. Output load capacitors. Capacitive load at the output that provides the option of tailoring the RF burst response time. The pads of the capacitors are left open by default. Bypass capacitors. The capacitors provide supply ac decoupling by forming a return path for the ac signal and reducing the noise reaching the input circuitry. The typical value is 0.1 F. RF input. Southwest Microwave 2.92 mm connector is used for input interface. To prevent the potential damage of the connectors, 2.92 mm (K type) cables are recommended. Rev. D | Page 20 of 22 Default Value R1 = 100 (0402 size), R2 = 100 (0402 size) C1, C2 = open C3 = 0.1 F (0402 size), C4 = 100 pF (0402 size) Data Sheet ADL6010 11617-049 11617-048 EVALUATION BOARD ASSEMBLY DRAWINGS Figure 45. ADL6010 Evaluation Board Layout, Top Side Figure 46. ADL6010 Evaluation Board Layout, Bottom Side Rev. D | Page 21 of 22 ADL6010 Data Sheet OUTLINE DIMENSIONS DETAIL A (JEDEC 95) 1.70 1.60 1.50 2.10 2.00 SQ 1.90 0.65 BSC 6 4 0.425 0.350 0.275 1 3 BOTTOM VIEW TOP VIEW PKG-004062 0.60 0.55 0.50 SEATING PLANE SIDE VIEW 0.05 MAX COPLANARITY 0.08 0.35 0.30 0.25 1.10 1.00 0.90 EXPOSED PAD 0.15 MIN P IN 1 IN D IC ATO R AR E A OP T IO N S (SEE DETAIL A) FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 02-04-2019-B PIN 1 INDICATOR AREA 0.20 REF Figure 47. 6-Lead Lead Frame Chip Scale Package [LFCSP] 2.00 mm x 2.00 mm Body and 0.55 mm Package Height (CP-6-7) Dimensions shown in millimeters ORDERING GUIDE Model 1 ADL6010ACPZN ADL6010ACPZN-R2 ADL6010ACPZN-R7 ADL6010SCPZN ADL6010SCPZN-R2 ADL6010SCPZN-R7 ADL6010-EVALZ 1 Temperature Range -40C to +85C -40C to +85C -40C to +85C -55C to +125C -55C to +125C -55C to +125C Package Description 6-Lead Lead Frame Chip Scale Package [LFCSP] 6-Lead Lead Frame Chip Scale Package [LFCSP] 6-Lead Lead Frame Chip Scale Package [LFCSP] 6-Lead Lead Frame Chip Scale Package [LFCSP] 6-Lead Lead Frame Chip Scale Package [LFCSP] 6-Lead Lead Frame Chip Scale Package [LFCSP] Evaluation Board Z = RoHS Compliant Part. (c)2014-2019 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D11617-0-9/19(D) Rev. D | Page 22 of 22 Package Option CP-6-7 CP-6-7 CP-6-7 CP-6-7 CP-6-7 CP-6-7 Ordering Quantity 1 250 3000 1 250 3000 1 Marking Code C1 C1 C1 Q23 Q23 Q23